* 2.2.22: oops in ll_rw_block
@ 2002-09-24 19:37 Philippe Troin
0 siblings, 0 replies; only message in thread
From: Philippe Troin @ 2002-09-24 19:37 UTC (permalink / raw)
To: linux-kernel
[1.] One line summary of the problem:
Accessing files can trigger this oops.
[2.] Full description of the problem/report:
The oops occured while I was running tripwire.
[3.] Keywords (i.e., modules, networking, kernel):
block-layer ll_rw_block oops
[4.] Kernel version (from /proc/version):
Linux version 2.2.22 (root@ceramic) (gcc version 2.95.4 20011002
(Debian prerelease)) #1 SMP Mon Sep 16 19:40:12 PDT 2002
[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
ksymoops 2.3.4 on i686 2.2.22. Options used
-V (default)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.2.22/ (default)
-m /boot/System.map-2.2.22 (default)
Warning: You did not tell me where to find symbol information. I will
assume that the log matches the kernel and modules that are running
right now and I'll use the default options above for symbol resolution.
If the current kernel and/or modules do not match the log, you can get
more accurate output by telling me the kernel version and where to find
map, modules, ksyms etc. ksymoops -h explains the options.
Unable to handle kernel paging request at virtual address 000ed0ac
current->tss.cr3 = 031ff000, %cr3 = 031ff000
*pde = 00000000
Oops: 0000
CPU: 0
EIP: 0010:[<c018464e>]
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010202
eax: 000ed0a4 ebx: 00000000 ecx: 00000807 edx: cae8be00
esi: c1c63e24 edi: 00000004 ebp: 00000008 esp: c1c63dcc
ds: 0018 es: 0018 ss: 0018
Process tripwire (pid: 4524, process nr: 108, stackpage=c1c63000)
Stack: 00000000 00000100 c8384620 c8384620 00076855 00000400 c8384620 00000807
00076855 c012e640 00000000 00000004 c1c63e24 cfbcd880 00000374 cfbcd880
00000000 c1c63ea4 00000807 00000004 cae8be00 00000000 cae8be00 c8795d20
Call Trace: [<c012e640>] [<c012e81c>] [<c0122f0e>] [<c0122e4b>] [<c012330c>] [<c01bd025>] [<c01236b3>]
[<c0123600>] [<c0112217>] [<c0111b8a>] [<c012be3e>] [<c010c7ad>] [<c010a7d0>]
Code: 28 8b 14 9e 8b 42 08 c1 e8 09 50 8d 42 10 50 8d 42 0e 50 31
>>EIP; c018464e <ll_rw_block+ce/228> <=====
Trace; c012e640 <brw_page+26c/368>
Trace; c012e81c <generic_readpage+8c/9c>
Trace; c0122f0e <try_to_read_ahead+f2/10c>
Trace; c0122e4b <try_to_read_ahead+2f/10c>
Trace; c012330c <do_generic_file_read+294/588>
Trace; c01bd025 <do_aic7xxx_isr+79/98>
Trace; c01236b3 <generic_file_read+63/7c>
Trace; c0123600 <file_read_actor+0/50>
Trace; c0112217 <do_level_ioapic_IRQ+9b/b0>
Trace; c0111b8a <smp_apic_timer_interrupt+16/20>
Trace; c012be3e <sys_read+c6/f8>
Trace; c010c7ad <apic_timer_interrupt+1d/28>
Trace; c010a7d0 <system_call+34/38>
Code; c018464e <ll_rw_block+ce/228>
00000000 <_EIP>:
Code; c018464e <ll_rw_block+ce/228> <=====
0: 28 8b 14 9e 8b 42 sub %cl,0x428b9e14(%ebx) <=====
Code; c0184654 <ll_rw_block+d4/228>
6: 08 c1 or %al,%cl
Code; c0184656 <ll_rw_block+d6/228>
8: e8 09 50 8d 42 call 428d5016 <_EIP+0x428d5016> 02a59664 Before first symbol
Code; c018465b <ll_rw_block+db/228>
d: 10 50 8d adc %dl,0xffffff8d(%eax)
Code; c018465e <ll_rw_block+de/228>
10: 42 inc %edx
Code; c018465f <ll_rw_block+df/228>
11: 0e push %cs
Code; c0184660 <ll_rw_block+e0/228>
12: 50 push %eax
Code; c0184661 <ll_rw_block+e1/228>
13: 31 00 xor %eax,(%eax)
1 warning issued. Results may not be reliable.
[6.] A small shell script or example program which triggers the
problem (if possible)
Not reproduced.
[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)
Debian GNU/Linux 2.2 (potato)
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux tantale 2.2.22 #1 SMP Mon Sep 16 19:40:12 PDT 2002 i686 unknown
Gnu C 2.95.2
Gnu make 3.79.1
binutils 2.9.5.0.37
util-linux
util-linux Note: /usr/bin/fdformat is obsolete and is no longer available.
util-linux Please use /usr/bin/superformat instead (make sure you have the
util-linux fdutils package installed first). Also, there had been some
util-linux major changes from version 4.x. Please refer to the documentation.
util-linux
mount 2.10q
modutils 2.3.11
e2fsprogs 1.18
Linux C Library 2.1.3
ldd: version 1.9.11
Procps 2.0.6
Net-tools 1.54
Console-tools 0.2.3
Sh-utils 2.0
Modules Loaded nfsd nfs lockd sunrpc vfat msdos fat isofs usbcore sr_mod cdrom lp parport_pc parport raid0 loop floppy cls_fw sch_sfq sch_tbf sch_prio ip_masq_ftp ne2k-pci 8390 3c509 3c59x af_packet
[7.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 1
model name : Pentium Pro
stepping : 2
cpu MHz : 149.694
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
sep_bug : yes
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
bogomips : 299.00
processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 1
model name : Pentium Pro
stepping : 2
cpu MHz : 149.694
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
sep_bug : yes
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
bogomips : 298.18
[7.3.] Module information (from /proc/modules):
nfsd 182688 8
nfs 69452 2
lockd 46352 1 [nfsd nfs]
sunrpc 64828 1 [nfsd nfs lockd]
vfat 9644 0 (unused)
msdos 5676 0 (unused)
fat 30816 0 [vfat msdos]
isofs 17280 0 (unused)
usbcore 47496 1
sr_mod 16744 0 (unused)
cdrom 27292 0 [sr_mod]
lp 5324 0
parport_pc 7588 1
parport 7832 1 [lp parport_pc]
raid0 2180 1
loop 7936 0 (unused)
floppy 47408 0
cls_fw 2032 1
sch_sfq 3256 2
sch_tbf 2360 1
sch_prio 2280 1
ip_masq_ftp 3816 0 (unused)
ne2k-pci 4404 1
8390 6684 0 [ne2k-pci]
3c509 6248 1
3c59x 21992 1
af_packet 6424 3
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
02f8-02ff : serial(set)
0300-030f : 3c509
0378-037a : parport0
03c0-03df : vga+
03f8-03ff : serial(set)
0778-077a : parport0
8000-801f : eth2
8100-817f : eth0
8200-82fe : aic7xxx
8300-8307 : serial(set)
8400-8407 : serial(set)
8500-8507 : serial(set)
8600-8607 : serial(set)
[7.5.] PCI information ('lspci -vvv' as root)
00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32 set
00:07.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:07.1 IDE interface: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II] (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Region 4: I/O ports at f000
00:0a.0 VGA compatible controller: S3 Inc. 86c988 [ViRGE/VX] (rev 02) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 15
Region 0: Memory at e0000000 (32-bit, non-prefetchable)
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RT8029(AS)
Subsystem: Realtek Semiconductor Co., Ltd. RT8029(AS)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 8000
00:0c.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
Subsystem: 3Com Corporation: Unknown device 9055
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 10 min, 10 max, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 8100
Region 1: Memory at e4000000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 SCSI storage controller: Adaptec 7892A (rev 02)
Subsystem: Adaptec: Unknown device e2a0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 40 min, 25 max, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 17
BIST result: 00
Region 0: I/O ports at 8200
Region 1: Memory at e4001000 (64-bit, non-prefetchable)
Capabilities: [dc] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 Serial controller: Siig Inc CyberSerial (4-port) 16650 (prog-if 02 [16550])
Subsystem: Siig Inc: Unknown device 2051
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 8300
Region 1: I/O ports at 8400
Region 2: I/O ports at 8500
Region 3: I/O ports at 8600
Capabilities: [a0] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[7.6.] SCSI information (from /proc/scsi/scsi)
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: SEAGATE Model: ST336752LW Rev: 0002
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: SEAGATE Model: ST318451LW Rev: 0002
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: SEAGATE Model: ST39103LW Rev: 0002
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: IBM Model: DRVS18V Rev: 0140
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 05 Lun: 00
Vendor: PIONEER Model: CD-ROM DR-U24X Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
N/A
[X.] Other notes, patches, fixes, workarounds:
Vanilla 2.2.22 plus kmsgdump patches.
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2002-09-24 19:32 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-09-24 19:37 2.2.22: oops in ll_rw_block Philippe Troin
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).