Re: 2.6.10-rc2-mm1 (8139too interrupt)

[Ralf Gerbig <rge@quengel.org>]

Hi Andrew,

* Andrew Morton writes:

> Ralf Gerbig <rge@quengel.org> wrote:
>> 
>> ...
>> [ide_intr+0/496] (ide_intr+0x0/0x1f0)
>> [<c0269c80>] (ide_intr+0x0/0x1f0)
>> [ide_intr+0/496] (ide_intr+0x0/0x1f0)
>> [<c0269c80>] (ide_intr+0x0/0x1f0)
>> [pg0+541642080/1068946432] (rtl8139_interrupt+0x0/0x1d0 [8139too])
>> [<e091dd60>] (rtl8139_interrupt+0x0/0x1d0 [8139too])
>> Disabling IRQ #19
>> 
>> NETDEV WATCHDOG: eth1: transmit timed out
>> eth1: Transmit timeout, status 0c 0005 c07f media 18.
>> eth1: Tx queue start entry 63  dirty entry 59.
>> eth1:  Tx descriptor 0 is 0008a03c.
>> eth1:  Tx descriptor 1 is 0008a06a.
>> eth1:  Tx descriptor 2 is 0008a03c.
>> eth1:  Tx descriptor 3 is 0008a03c. (queue head)
>> eth1: link up, 10Mbps, full-duplex, lpa 0x4061
>> 
>> and the interface is dead. Rmmod/insmod does not help.

> Does this happen immediately, or does it take a bit of load first?

dunno exactly, the log shows the trace right at boot and again after
about 6h.
Logged in the next morning and found no new messages on lkml, looked
at the log, did the ifdown -- rmmod -- modprobe -- ifup, still no joy,
rebooted -- the pppd connection came up but went down while changing
to runlevel 5.

> We should be looking for changes in 8139too, changes in IDE or changes in
> interrupt setup.  Usually it is the latter.  It would be helpful if you
> could gather the boot-time dmesg output from rc1-mm5 and rc2-mm1 and do a
> `diff -u', see what changed.

--- /var/log/boot.msg	2004-11-17 11:37:57.000000000 +0100
+++ /var/log/boot.omsg	2004-11-17 11:36:08.000000000 +0100
@@ -1,10 +1,10 @@
-Inspecting /boot/System.map-2.6.10-rc1-mm5
-Loaded 27073 symbols from /boot/System.map-2.6.10-rc1-mm5.
+Inspecting /boot/System.map-2.6.10-rc2-mm1
+Loaded 26846 symbols from /boot/System.map-2.6.10-rc2-mm1.
 Symbols match kernel version 2.6.10.
 No module symbols loaded - kernel modules not enabled.
 
 klogd 1.4.1, log source = ksyslog started.
-<4>Linux version 2.6.10-rc1-mm5 (rge@gerlin1) (gcc version 3.3.3 (SuSE Linux)) #1 Thu Nov 11 20:18:40 CET 2004
+<4>Linux version 2.6.10-rc2-mm1 (rge@gerlin1) (gcc version 3.3.3 (SuSE Linux)) #1 Tue Nov 16 21:48:13 CET 2004
 <6>BIOS-provided physical RAM map:
 <4> BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
 <4> BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
@@ -34,23 +34,24 @@
 <6>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
 <4>IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
 <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
+<4>ACPI: BIOS IRQ0 pin2 override ignored.
 <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
-<7>ACPI: IRQ0 used by override.
-<7>ACPI: IRQ2 used by override.
 <7>ACPI: IRQ9 used by override.
 <4>Enabling APIC mode:  Flat.  Using 1 I/O APICs
 <6>Using ACPI (MADT) for SMP configuration information
 <4>Built 1 zonelists
+<7>mapped APIC to ffffd000 (fee00000)
+<7>mapped IOAPIC to ffffc000 (fec00000)
 <6>Initializing CPU#0
-<4>Kernel command line: root=/dev/hda2 console=ttyS1,38400 console=tty0 3
-<4>CPU 0 irqstacks, hard=c045c000 soft=c045b000
+<4>Kernel command line: root=/dev/hda2 3
+<4>CPU 0 irqstacks, hard=c0453000 soft=c0452000
 <4>PID hash table entries: 2048 (order: 11, 32768 bytes)
-<4>Detected 2088.590 MHz processor.
+<4>Detected 2088.645 MHz processor.
 <6>Using pmtmr for high-res timesource
 <4>Console: colour VGA+ 80x25
 <4>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
 <4>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
-<6>Memory: 515032k/524224k available (2178k kernel code, 8632k reserved, 1063k data, 168k init, 0k highmem)
+<6>Memory: 515072k/524224k available (2143k kernel code, 8592k reserved, 1055k data, 176k init, 0k highmem)
 <4>Checking if this processor honours the WP bit even in supervisor mode... Ok.
 <7>Calibrating delay loop... 4136.96 BogoMIPS (lpj=2068480)
 <4>Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
@@ -68,14 +69,10 @@
 <4> tbxface-0117 [02] acpi_load_tables      : ACPI Tables successfully acquired
 <4>Parsing all Control Methods:...................................................................................................................................................................................................................................................................................
 <4>Table [DSDT](id F004) - 806 Objects with 77 Devices 275 Methods 36 Regions
-<4>ACPI Namespace successfully loaded at root c0488120
+<4>ACPI Namespace successfully loaded at root c047f120
 <4>evxfevnt-0093 [03] acpi_enable           : Transition to ACPI mode successful
 <4>ENABLING IO-APIC IRQs
-<6>..TIMER: vector=0x31 pin1=2 pin2=-1
-<3>..MP-BIOS bug: 8254 timer not connected to IO-APIC
-<6>...trying to set up timer (IRQ0) through the 8259A ...  failed.
-<6>...trying to set up timer as Virtual Wire IRQ... failed.
-<6>...trying to set up timer as ExtINT IRQ... works.
+<6>..TIMER: vector=0x31 pin1=0 pin2=-1
 <6>NET: Registered protocol family 16
 <6>PCI: PCI BIOS revision 2.10 entry at 0xfb4c0, last bus=2
 <6>PCI: Using configuration type 1
@@ -160,7 +157,6 @@
 <4>vesafb: probe of vesafb0 failed with error -6
 <6>isapnp: Scanning for PnP cards...
 <6>isapnp: No Plug & Play device found
-<6>[drm] Initialized drm 1.0.0 20040925
 <6>ACPI: PS/2 Keyboard Controller [PS2K] at I/O 0x60, 0x64, irq 1
 <6>ACPI: PS/2 Mouse Controller [PS2M] at irq 12
 <6>serio: i8042 AUX port at 0x60,0x64 irq 12
@@ -223,8 +219,8 @@
 <6>hdg: 40020624 sectors (20490 MB) w/2048KiB Cache, CHS=39703/16/63, UDMA(100)
 <7>hdg: cache flushes not supported
 <6> hdg: hdg1 hdg2 hdg3 hdg4
-<7>libata version 1.02 loaded.
-<7>sata_sil version 0.54
+<7>libata version 1.10 loaded.
+<7>sata_sil version 0.8
 <4>ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
 <6>ACPI: PCI interrupt 0000:01:0c.0[A] -> GSI 16 (level, high) -> IRQ 16
 <6>ata1: SATA max UDMA/100 cmd 0xE0802080 ctl 0xE080208A bmdma 0xE0802000 irq 16
@@ -255,7 +251,7 @@
 <4>HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1 
 <6>EXT3-fs: mounted filesystem with ordered data mode.
 <4>VFS: Mounted root (ext3 filesystem) readonly.
-<6>Freeing unused kernel memory: 168k freed
+<6>Freeing unused kernel memory: 176k freed
 <6>kjournald starting.  Commit interval 5 seconds
 <6>EXT3 FS on hda2, internal journal
 <5>SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
@@ -281,7 +277,7 @@
 Kernel logging (ksyslog) stopped.
 Kernel log daemon terminating.
 
-Boot logging started on /dev/tty1(/dev/console) at Wed Nov 17 11:37:12 2004
+Boot logging started on /dev/tty1(/dev/console) at Wed Nov 17 11:32:45 2004

---------------------------------------

--- log-rc1-mm5	2004-11-17 22:55:19.088281605 +0100
+++ log-rc2-mm1	2004-11-17 22:55:31.521176195 +0100
@@ -1,34 +1,32 @@
 syslogd 1.4.1: restart.
-pppd[3551]: Plugin rp-pppoe.so loaded.
-pppd[3551]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
-pppd[3551]: pppd 2.4.2 started by root, uid 0
-pppd[3551]: PPP session is 1892
-pppd[3551]: Using interface ppp0
-pppd[3551]: Connect: ppp0 <--> eth1
-pppd[3551]: Couldn't increase MTU to 1500
-pppd[3551]: Couldn't increase MRU to 1500
-pppd[3551]: Couldn't increase MRU to 1500
-pppd[3551]: Couldn't increase MTU to 1500
-pppd[3551]: Couldn't increase MRU to 1500
-pppd[3551]: Couldn't increase MRU to 1500
-pppd[3551]: PAP authentication succeeded
-pppd[3551]: peer from calling number <me> authorized
-pppd[3551]: local  IP address <mine>
-pppd[3551]: remote IP address <the other>
-pppd[3551]: Script /etc/ppp/ip-up finished (pid 3705), status = 0x0
-/sbin/hotplug[4730]: /etc/hotplug/ieee1394.agent: line 22: VENDOR_ID: Bad invocation: $VENDOR_ID is not set
+pppd[3535]: Plugin rp-pppoe.so loaded.
+pppd[3535]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
+pppd[3535]: pppd 2.4.2 started by root, uid 0
+pppd[3535]: PPP session is 6975
+pppd[3535]: Using interface ppp0
+pppd[3535]: Connect: ppp0 <--> eth1
+pppd[3535]: Couldn't increase MTU to 1500
+pppd[3535]: Couldn't increase MRU to 1500
+pppd[3535]: Couldn't increase MRU to 1500
+pppd[3535]: Couldn't increase MTU to 1500
+pppd[3535]: Couldn't increase MRU to 1500
+pppd[3535]: Couldn't increase MRU to 1500
+pppd[3535]: PAP authentication succeeded
+pppd[3535]: peer from calling number <me> authorized
+pppd[3535]: local  IP address <mine>
+pppd[3535]: remote IP address <the other>
+pppd[3535]: Script /etc/ppp/ip-up finished (pid 3708), status = 0x0
+/etc/hotplug/usb.agent[4083]: need a device for this command
+/etc/hotplug/usb.agent[4224]: need a device for this command
+/etc/hotplug/usb.agent[4277]: need a device for this command
+/etc/hotplug/usb.agent[4473]: need a device for this command
+/etc/hotplug/usb.agent[4462]: need a device for this command
+/sbin/hotplug[4643]: /etc/hotplug/ieee1394.agent: line 22: VENDOR_ID: Bad invocation: $VENDOR_ID is not set
+/sbin/hotplug[4770]: /etc/hotplug/ieee1394.agent: line 22: VENDOR_ID: Bad invocation: $VENDOR_ID is not set
+/sbin/hotplug[4789]: /etc/hotplug/ieee1394.agent: line 22: VENDOR_ID: Bad invocation: $VENDOR_ID is not set
 kernel: klogd 1.4.1, log source = /proc/kmsg started.
-kernel: Inspecting /boot/System.map-2.6.10-rc1-mm5
-kernel: Loaded 27073 symbols from /boot/System.map-2.6.10-rc1-mm5.
+kernel: Inspecting /boot/System.map-2.6.10-rc2-mm1
+kernel: Loaded 26846 symbols from /boot/System.map-2.6.10-rc2-mm1.
 kernel: Symbols match kernel version 2.6.10.
 kernel: No module symbols loaded - kernel modules not enabled. 
 kernel: ip_tables: (C) 2000-2002 Netfilter core team
@@ -59,105 +57,102 @@
 kernel: eth0: no link during initialization.
 kernel: 8139too Fast Ethernet driver 0.9.27
 kernel: ACPI: PCI interrupt 0000:01:0b.0[A] -> GSI 19 (level, high) -> IRQ 19
-kernel: eth1: RealTek RTL8139 at 0xe08ee000, 00:04:61:4a:11:a5, IRQ 19
+kernel: eth1: RealTek RTL8139 at 0xe08ea000, 00:04:61:4a:11:a5, IRQ 19
 kernel: eth1:  Identified 8139 chip type 'RTL-8101'
 kernel: eth1: link up, 10Mbps, full-duplex, lpa 0x4061
 kernel: PPP generic driver version 2.4.2
 kernel: NET: Registered protocol family 24
+kernel: ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
+kernel: ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 21 (level, high) -> IRQ 21
+kernel: ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
+kernel: PCI: Setting latency timer of device 0000:00:02.2 to 64
+kernel: ehci_hcd 0000:00:02.2: irq 21, pci mem 0xdd004000
 kernel: Linux agpgart interface v0.100 (c) Dave Jones
+kernel: ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
+kernel: PCI: cache line size of 64 is not supported by device 0000:00:02.2
+kernel: ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
+kernel: ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
+kernel: hub 1-0:1.0: USB hub found
+kernel: hub 1-0:1.0: 6 ports detected
 kernel: agpgart: Detected NVIDIA nForce2 chipset
 kernel: agpgart: Maximum main memory to use for agp memory: 439M
 kernel: agpgart: AGP aperture is 128M @ 0xc0000000
-kernel: ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
-kernel: ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
-kernel: ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 21 (level, high) -> IRQ 21
+kernel: ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
+kernel: ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 20 (level, high) -> IRQ 20
 kernel: ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller
 kernel: PCI: Setting latency timer of device 0000:00:02.0 to 64
-kernel: ohci_hcd 0000:00:02.0: irq 21, pci mem 0xdd002000
-kernel: ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
-kernel: hub 1-0:1.0: USB hub found
-kernel: hub 1-0:1.0: 3 ports detected
-kernel: ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
-kernel: ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 20 (level, high) -> IRQ 20
-kernel: ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2)
-kernel: PCI: Setting latency timer of device 0000:00:02.1 to 64
-kernel: ohci_hcd 0000:00:02.1: irq 20, pci mem 0xdd003000
-kernel: ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
-kernel: usb 1-3: new low speed USB device using ohci_hcd and address 2
+kernel: ohci_hcd 0000:00:02.0: irq 20, pci mem 0xdd002000
+kernel: ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
 kernel: hub 2-0:1.0: USB hub found
 kernel: hub 2-0:1.0: 3 ports detected
-kernel: i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
-kernel: i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5040
-kernel: ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
-kernel: ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 22 (level, high) -> IRQ 22
-kernel: ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
-kernel: PCI: Setting latency timer of device 0000:00:02.2 to 64
-kernel: ehci_hcd 0000:00:02.2: irq 22, pci mem 0xdd004000
-kernel: ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
-kernel: PCI: cache line size of 64 is not supported by device 0000:00:02.2
-kernel: ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
+kernel: ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22
+kernel: ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 22 (level, high) -> IRQ 22
+kernel: ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2)
+kernel: PCI: Setting latency timer of device 0000:00:02.1 to 64
+kernel: ohci_hcd 0000:00:02.1: irq 22, pci mem 0xdd003000
+kernel: ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
 kernel: hub 3-0:1.0: USB hub found
-kernel: hub 3-0:1.0: 6 ports detected
+kernel: hub 3-0:1.0: 3 ports detected
+kernel: usb 2-3: new low speed USB device using ohci_hcd and address 2
 kernel: ieee1394: Initialized config rom entry `ip1394'
-kernel: usb 1-3: USB disconnect, address 2
+kernel: i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
+kernel: i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5040
 kernel: ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
 kernel: ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
 kernel: ACPI: PCI interrupt 0000:01:0d.0[A] -> GSI 17 (level, high) -> IRQ 17
 kernel: ohci1394: fw-host0: Unexpected PCI resource length of 1000!
-kernel: usb 1-3: new low speed USB device using ohci_hcd and address 3
 kernel: ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17]  MMIO=[dc007000-dc0077ff]  Max Packet=[2048]
 kernel: ieee1394: Host added: ID:BUS[0-00:1023]  GUID[000461000003e56a]
-/sbin/hotplug[4955]: /etc/hotplug/ieee1394.agent: line 22: VENDOR_ID: Bad invocation: $VENDOR_ID is not set
-/sbin/hotplug[4936]: /etc/hotplug/ieee1394.agent: line 22: VENDOR_ID: Bad invocation: $VENDOR_ID is not set
-in.identd[5083]: started
+in.identd[5088]: started
 kernel: NET: Registered protocol family 10
-kernel: Disabled Privacy Extensions on device c03bf8c0(lo)
+kernel: Disabled Privacy Extensions on device c03b55a0(lo)
 kernel: IPv6 over IPv4 tunneling driver
+kernel: Disabled Privacy Extensions on device dc330000(sit0)
 ip-up: fetchmail: no mailservers have been specified.
-kernel: snd_intel8x0: Unknown parameter `#enable'
-/sbin/hotplug[5611]: /sbin/hotplug: line 74: [: too many arguments
-kernel: ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
-kernel: ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 21 (level, high) -> IRQ 21
-kernel: PCI: Setting latency timer of device 0000:00:06.0 to 64
-named[5664]: starting BIND 9.2.3 -t /var/lib/named -u named
-named[5664]: using 1 CPU
-sshd[5672]: Server listening on :: port 22.
-/sbin/hotplug[5611]: /sbin/hotplug: line 74: [: too many arguments
 kernel: input: USB HID v1.10 Keyboard [Twinhan Tech Remote Control] on usb-0000:00:02.0-3
 kernel: input: USB HID v1.10 Mouse [Twinhan Tech Remote Control] on usb-0000:00:02.0-3
 kernel: usbcore: registered new driver usbhid
 kernel: drivers/usb/input/hid-core.c: v2.0:USB HID core driver
+kernel: snd_intel8x0: Unknown parameter `#enable'
+kernel: ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
+kernel: ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 21 (level, high) -> IRQ 21
+kernel: PCI: Setting latency timer of device 0000:00:06.0 to 64
+sshd[5696]: Server listening on :: port 22.
+/sbin/hotplug[5674]: /sbin/hotplug: line 74: [: too many arguments
+named[5794]: starting BIND 9.2.3 -t /var/lib/named -u named
+named[5794]: using 1 CPU
+/sbin/hotplug[5674]: /sbin/hotplug: line 74: [: too many arguments
+named[5794]: loading configuration from '/etc/named.conf'
 ip-up: postqueue: fatal: Cannot flush mail queue - mail system is down
 ifup: No configuration found for sit0
 su: (to news) root on /dev/pts/2
 su: pam_unix2: session started for user news, service su 
@@ -173,7 +168,6 @@
 dhcpd: Wrote 0 deleted host decls to leases file.
 dhcpd: Wrote 0 new dynamic host decls to leases file.
 dhcpd: Wrote 0 leases to leases file.
-kernel: parport_pc: Ignoring new-style parameters in presence of obsolete ones
 kernel: parport: PnPBIOS parport detected.
 kernel: parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
 dhcpd: Listening on Socket/eth0/192.168.100.0/24
@@ -182,79 +176,162 @@
 kernel: lp0: using parport0 (interrupt-driven).
 kernel: usbcore: registered new driver usbserial
 kernel: drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
[ ... ]
+kernel: [drm] Initialized drm 1.0.0 20040925
 kernel: [drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies Inc RV280 [Radeon 9200]
 kernel: ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 19 (level, high) -> IRQ 19
-kernel: [drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
-kernel: [drm:drm_unlock] *ERROR* Process 10713 using kernel context 0
+kernel: agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
+kernel: agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
+kernel: agpgart: Putting AGP V3 device at 0000:02:00.0 into 4x mode
+kernel: [drm] Loading R200 Microcode
 kernel: drivers/usb/input/hid-input.c: event field not found
+kernel: irq 19: nobody cared!
+kernel:  [__report_bad_irq+42/144] __report_bad_irq+0x2a/0x90
+kernel:  [<c01388ea>] __report_bad_irq+0x2a/0x90
+kernel:  [handle_IRQ_event+57/112] handle_IRQ_event+0x39/0x70
+kernel:  [<c01381a9>] handle_IRQ_event+0x39/0x70
+kernel:  [note_interrupt+149/192] note_interrupt+0x95/0xc0
+kernel:  [<c0138a05>] note_interrupt+0x95/0xc0
+kernel:  [__do_IRQ+357/384] __do_IRQ+0x165/0x180
+kernel:  [<c0138345>] __do_IRQ+0x165/0x180
+kernel:  [do_IRQ+71/112] do_IRQ+0x47/0x70
+kernel:  [<c0105907>] do_IRQ+0x47/0x70
+kernel:  =======================
+kernel:  [common_interrupt+26/32] common_interrupt+0x1a/0x20
+kernel:  [<c0103c52>] common_interrupt+0x1a/0x20
+kernel:  [default_idle+0/48] default_idle+0x0/0x30
+kernel:  [<c0101030>] default_idle+0x0/0x30
+kernel:  [default_idle+35/48] default_idle+0x23/0x30
+kernel:  [<c0101053>] default_idle+0x23/0x30
+kernel:  [cpu_idle+54/112] cpu_idle+0x36/0x70
+kernel:  [<c01010d6>] cpu_idle+0x36/0x70
+kernel:  [start_kernel+346/384] start_kernel+0x15a/0x180
+kernel:  [<c042180a>] start_kernel+0x15a/0x180
+kernel:  [unknown_bootoption+0/480] unknown_bootoption+0x0/0x1e0
+kernel:  [<c0421380>] unknown_bootoption+0x0/0x1e0
+kernel: handlers:
+kernel: [ide_intr+0/496] (ide_intr+0x0/0x1f0)
+kernel: [<c0269c80>] (ide_intr+0x0/0x1f0)
+kernel: [ide_intr+0/496] (ide_intr+0x0/0x1f0)
+kernel: [<c0269c80>] (ide_intr+0x0/0x1f0)
+kernel: [pg0+541625696/1068946432] (rtl8139_interrupt+0x0/0x1d0 [8139too])
+kernel: [<e0919d60>] (rtl8139_interrupt+0x0/0x1d0 [8139too])
+kernel: Disabling IRQ #19
+kernel: NETDEV WATCHDOG: eth1: transmit timed out
+kernel: eth1: Transmit timeout, status 0c 0005 c07f media 18.
+kernel: eth1: Tx queue start entry 70  dirty entry 66.
+kernel: eth1:  Tx descriptor 0 is 0008a06a.
+kernel: eth1:  Tx descriptor 1 is 0008a03c.
+kernel: eth1:  Tx descriptor 2 is 0008a03c. (queue head)
+kernel: eth1:  Tx descriptor 3 is 0008a03c.
+kernel: eth1: link up, 10Mbps, full-duplex, lpa 0x4061
+kernel: NETDEV WATCHDOG: eth1: transmit timed out
+kernel: eth1: Transmit timeout, status 0d 0004 c07f media 18.
+kernel: eth1: Tx queue start entry 4  dirty entry 0.
+kernel: eth1:  Tx descriptor 0 is 0008a062. (queue head)
+kernel: eth1:  Tx descriptor 1 is 0008a062.
+kernel: eth1:  Tx descriptor 2 is 0008a03c.
+kernel: eth1:  Tx descriptor 3 is 0008a03c.
+kernel: eth1: link up, 10Mbps, full-duplex, lpa 0x4061
+pppd[3535]: No response to 5 echo-requests
+pppd[3535]: Serial link appears to be disconnected.
+pppd[3535]: Couldn't increase MTU to 1500
+pppd[3535]: Couldn't increase MRU to 1500
+pppd[3535]: Script /etc/ppp/ip-down finished (pid 11312), status = 0x0
+pppd[3535]: Connection terminated.
+pppd[3535]: Connect time 2.1 minutes.
+pppd[3535]: Sent 3160 bytes, received 8797 bytes.
+kernel: NETDEV WATCHDOG: eth1: transmit timed out
+kernel: eth1: Transmit timeout, status 0c 0005 c07f media 18.
+kernel: eth1: Tx queue start entry 4  dirty entry 0.
+kernel: eth1:  Tx descriptor 0 is 0008a03c. (queue head)
+kernel: eth1:  Tx descriptor 1 is 0008a03c.
+kernel: eth1:  Tx descriptor 2 is 0008a03c.
+kernel: eth1:  Tx descriptor 3 is 0008a03c.
+kernel: eth1: link up, 10Mbps, full-duplex, lpa 0x4061
+pppd[3535]: Timeout waiting for PADO packets
+pppd[3535]: Unable to complete PPPoE Discovery
+kernel: NETDEV WATCHDOG: eth1: transmit timed out
+kernel: eth1: Transmit timeout, status 0c 0005 c07f media 18.
+kernel: eth1: Tx queue start entry 4  dirty entry 0.
+kernel: eth1:  Tx descriptor 0 is 0008a03c. (queue head)
+kernel: eth1:  Tx descriptor 1 is 0008a03c.
+kernel: eth1:  Tx descriptor 2 is 0008a03c.
+kernel: eth1:  Tx descriptor 3 is 0008a03c.
+kernel: eth1: link up, 10Mbps, full-duplex, lpa 0x4061
+pppd[3535]: Timeout waiting for PADO packets
+pppd[3535]: Unable to complete PPPoE Discovery
+pppd[3535]: Timeout waiting for PADO packets
+pppd[3535]: Unable to complete PPPoE Discovery


Ralf
-- 
 P:     Linus Torvalds			patch-2.2.4
-S:     Buried alive in diapers
+S:     Buried alive in reporters