* 2.5.39: hdparm: HDIO_SET_DMA failed: Operation not permitted
@ 2002-10-01 14:18 Olaf Dietsche
2002-10-01 14:45 ` Olaf Dietsche
0 siblings, 1 reply; 4+ messages in thread
From: Olaf Dietsche @ 2002-10-01 14:18 UTC (permalink / raw)
To: linux-kernel
Hi,
with 2.5.39 I get the following error (2.5.40/www.kernel.org is
unavailable at the moment):
# hdparm -d 1 /dev/hda/0
/dev/hda/0:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
It works with 2.4.14. I haven't tried any other.
$ ls -la /dev/hda/0
brw-rw---- 1 root disk 3, 0 21. Jul 1998 /dev/hda/0
$ /sbin/hdparm -V
hdparm v5.2
# lspci -v
00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
Subsystem: Elitegroup Computer Systems: Unknown device 0996
Flags: bus master, medium devsel, latency 8
Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: e4000000-e7ffffff
Capabilities: [80] Power Management version 2
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at d000 [size=256]
Memory at ea000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Subsystem: Elitegroup Computer Systems: Unknown device 0996
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at d400 [size=16]
Capabilities: [c0] Power Management version 2
01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 PF (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 5446
Flags: bus master, stepping, 66Mhz, medium devsel, latency 32, IRQ 10
Memory at e4000000 (32-bit, prefetchable) [size=64M]
I/O ports at c000 [size=256]
Memory at e9000000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Capabilities: [5c] Power Management version 2
Motherboard is an Elitegroup K7VTA3
.config is:
CONFIG_X86=y
CONFIG_ISA=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_EXPERIMENTAL=y
CONFIG_NET=y
CONFIG_SYSVIPC=y
CONFIG_SYSCTL=y
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
CONFIG_M686=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=5
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_PPRO_FENCE=y
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
CONFIG_NOHIGHMEM=y
CONFIG_MTRR=y
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_DEBUG=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_BUS=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
CONFIG_PM=y
CONFIG_PCI=y
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_NAMES=y
CONFIG_KCORE_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
CONFIG_BLK_DEV_FD=m
CONFIG_BLK_DEV_LOOP=m
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_BLK_DEV_ADMA=y
CONFIG_IDEDMA_AUTO=y
CONFIG_BLK_DEV_IDE_MODES=y
CONFIG_PACKET=m
CONFIG_NETFILTER=y
CONFIG_UNIX=m
CONFIG_INET=y
CONFIG_INET_ECN=y
CONFIG_SYN_COOKIES=y
CONFIG_IPV6_SCTP__=y
CONFIG_NETDEVICES=y
CONFIG_NET_ETHERNET=y
CONFIG_NET_PCI=y
CONFIG_8139TOO=m
CONFIG_PPP=m
CONFIG_PPP_ASYNC=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPPOE=m
CONFIG_INPUT=y
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_SERIAL=m
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_CORE=y
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=m
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m
CONFIG_I2C_PROC=m
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_PROC_FS=y
CONFIG_DEVPTS_FS=y
CONFIG_EXT2_FS=y
CONFIG_NFS_FS=m
CONFIG_NFSD=m
CONFIG_SUNRPC=m
CONFIG_LOCKD=m
CONFIG_EXPORTFS=m
CONFIG_MSDOS_PARTITION=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_UTF8=m
CONFIG_VGA_CONSOLE=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_SLAB=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_SPINLOCK=y
CONFIG_KALLSYMS=y
CONFIG_X86_EXTRA_IRQS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_SECURITY_CAPABILITIES=y
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_X86_BIOS_REBOOT=y
If you need more info, please tell me.
Regards, Olaf.
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.5.39: hdparm: HDIO_SET_DMA failed: Operation not permitted
2002-10-01 14:18 2.5.39: hdparm: HDIO_SET_DMA failed: Operation not permitted Olaf Dietsche
@ 2002-10-01 14:45 ` Olaf Dietsche
2002-10-01 14:49 ` Jens Axboe
0 siblings, 1 reply; 4+ messages in thread
From: Olaf Dietsche @ 2002-10-01 14:45 UTC (permalink / raw)
To: linux-kernel
Olaf Dietsche <olaf.dietsche--list.linux-kernel@exmail.de> writes:
> with 2.5.39 I get the following error (2.5.40/www.kernel.org is
> unavailable at the moment):
>
> # hdparm -d 1 /dev/hda/0
>
> /dev/hda/0:
> setting using_dma to 1 (on)
> HDIO_SET_DMA failed: Operation not permitted
> using_dma = 0 (off)
I forgot to add dmesg output:
Linux version 2.5.39 (olaf@goat) (gcc version 2.95.4 20011002 (Debian prerelease)) #2 Tue Oct 1 15:39:25 MEST 2002
Video mode to be used for restore is ffff
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131056
DMA zone: 4096 pages
Normal zone: 126960 pages
HighMem zone: 0 pages
ACPI: RSDP (v000 VIA694 ) @ 0x000f7400
ACPI: RSDT (v001 VIA694 AWRDACPI 16944.11825) @ 0x1fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 16944.11825) @ 0x1fff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: MADT not present
Building zonelist for node : 0
Kernel command line: BOOT_IMAGE=Lx-2.5.39-2 ro root=302
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1200.339 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2367.48 BogoMIPS
Memory: 516084k/524224k available (1061k kernel code, 7752k reserved, 427k data, 244k init, 0k highmem)
Security Scaffold v1.0.0 initialized
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Machine check exception polling timer started.
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU: AMD Duron(tm) processor stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1199.0923 MHz.
..... host bus clock speed is 199.0987 MHz.
cpu: 0, clocks: 199987, slice: 99993
CPU0<T0:199984,T1:99984,D:7,S:99993,C:199987>
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
mtrr: v2.0 (20020519)
PCI: PCI BIOS revision 2.10 entry at 0xfb010, last bus=1
PCI: Using configuration type 1
adding '' to cpu class interfaces
ACPI: Subsystem revision 20020918
tbxface-0099 [03] Acpi_load_tables : ACPI Tables successfully loaded
Parsing Methods:..............................................................................................
Table [DSDT] - 357 Objects with 33 Devices 94 Methods 21 Regions
ACPI Namespace successfully loaded at root c02e923c
evxfevnt-0074 [04] Acpi_enable : Transition to ACPI mode successful
Executing all Device _STA and_INI methods:.................................
33 Devices found containing: 33 _STA, 1 _INI methods
Completing Region/Field/Buffer/Package initialization:...............................................
Initialized 18/21 Regions 0/0 Fields 16/16 Buffers 13/13 Packages (357 nodes)
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
pci_bind-0191 [04] acpi_pci_bind : Device 00:00:11.02 not present in PCI namespace
pci_bind-0191 [04] acpi_pci_bind : Device 00:00:11.03 not present in PCI namespace
pci_bind-0191 [04] acpi_pci_bind : Device 00:00:11.04 not present in PCI namespace
pci_bind-0191 [04] acpi_pci_bind : Device 00:00:11.05 not present in PCI namespace
pci_bind-0191 [04] acpi_pci_bind : Device 00:00:11.06 not present in PCI namespace
pci_bind-0191 [04] acpi_pci_bind : Device 00:00:12.00 not present in PCI namespace
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15, disabled)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
spurious 8259A interrupt: IRQ7.
Starting kswapd
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec pool[0]: 1 bvecs: 256 entries (12 bytes)
biovec pool[1]: 4 bvecs: 256 entries (48 bytes)
biovec pool[2]: 16 bvecs: 256 entries (192 bytes)
biovec pool[3]: 64 bvecs: 256 entries (768 bytes)
biovec pool[4]: 128 bvecs: 256 entries (1536 bytes)
biovec pool[5]: 256 bvecs: 256 entries (3072 bytes)
aio_setup: sizeof(struct page) = 40
Capability LSM initialized
ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
block request queues:
128 requests per read queue
128 requests per write queue
8 requests per batch
enter congestion at 31
exit congestion at 33
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: SAMSUNG SV4003H, ATA DISK drive
hdb: _NEC CD-ROM CD-3002A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: host protected area => 1
hda: 78242190 sectors (40060 MB) w/468KiB Cache, CHS=4870/255/63
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 hda15 hda16 hda17 hda18 hda19 hda20 hda21 >
register interface 'mouse' with class 'input
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 244k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Adding 497972k swap on /dev/hda/10. Priority:-1 extents:1
parport0: PC-style at 0x378 (0x778) [PCSPP(,...)]
parport0: irq 7 detected
lp0: using parport0 (polling).
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xe0863000, 00:e0:7d:c5:b5:57, IRQ 5
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
MTRR: setting reg 2
input: PS/2 Logitech Mouse on isa0060/serio1
psmouse.c: Lost synchronization, throwing 1 bytes away.
psmouse.c: Lost synchronization, throwing 2 bytes away.
hdb: ATAPI 52X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
Regards, Olaf.
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.5.39: hdparm: HDIO_SET_DMA failed: Operation not permitted
2002-10-01 14:45 ` Olaf Dietsche
@ 2002-10-01 14:49 ` Jens Axboe
2002-10-01 15:53 ` Olaf Dietsche
0 siblings, 1 reply; 4+ messages in thread
From: Jens Axboe @ 2002-10-01 14:49 UTC (permalink / raw)
To: Olaf Dietsche; +Cc: linux-kernel
On Tue, Oct 01 2002, Olaf Dietsche wrote:
> Olaf Dietsche <olaf.dietsche--list.linux-kernel@exmail.de> writes:
>
> > with 2.5.39 I get the following error (2.5.40/www.kernel.org is
> > unavailable at the moment):
> >
> > # hdparm -d 1 /dev/hda/0
> >
> > /dev/hda/0:
> > setting using_dma to 1 (on)
> > HDIO_SET_DMA failed: Operation not permitted
> > using_dma = 0 (off)
>
> I forgot to add dmesg output:
[snip]
looks like you forgot to enable via support
--
Jens Axboe
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2002-10-01 15:49 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-10-01 14:18 2.5.39: hdparm: HDIO_SET_DMA failed: Operation not permitted Olaf Dietsche
2002-10-01 14:45 ` Olaf Dietsche
2002-10-01 14:49 ` Jens Axboe
2002-10-01 15:53 ` Olaf Dietsche
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).