Re: [PATCH v5 2/4] arm64: dts: qcom: sc7280: Add PCIe and PHY related nodes

[Prasad Malisetty <pmaliset@codeaurora.org>]

On 2021-08-12 11:37, Manivannan Sadhasivam wrote:
> On Tue, Aug 10, 2021 at 09:38:34AM +0530, Prasad Malisetty wrote:
>> Add PCIe controller and PHY nodes for sc7280 SOC.
>> 
>> Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
>> ---
>>  arch/arm64/boot/dts/qcom/sc7280.dtsi | 126 
>> +++++++++++++++++++++++++++++++++++
>>  1 file changed, 126 insertions(+)
>> 
>> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi 
>> b/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> index 53a21d0..4500d88 100644
>> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
>> @@ -16,6 +16,7 @@
>>  #include <dt-bindings/reset/qcom,sdm845-pdc.h>
>>  #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>>  #include <dt-bindings/thermal/thermal.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> 
>>  / {
>>  	interrupt-parent = <&intc>;
>> @@ -586,6 +587,119 @@
>>  			qcom,bcm-voters = <&apps_bcm_voter>;
>>  		};
>> 
>> +		pcie1: pci@1c08000 {
>> +			compatible = "qcom,pcie-sc7280", "qcom,pcie-sm8250", 
>> "snps,dw-pcie";
> 
> Why 2 fallbacks? Fallbacks are meant to be used when the "fallback" 
> compatible
> driver can fully support the hw. In this case, neither
> "qcom,pcie-sm8250" nor "snps,dw-pcie"
> can work properly, right?
> 
> I did the same mistake for SM8250 though... But please get rid of them.
> 
Hi Mani,

Thanks for your review and comments.

Sure I agree, will remove one of the fallbacks and update the changes in 
next version.

Thanks
-Prasad

>> +			reg = <0 0x01c08000 0 0x3000>,
>> +			      <0 0x40000000 0 0xf1d>,
>> +			      <0 0x40000f20 0 0xa8>,
>> +			      <0 0x40001000 0 0x1000>,
>> +			      <0 0x40100000 0 0x100000>;
>> +
>> +			reg-names = "parf", "dbi", "elbi", "atu", "config";
>> +			device_type = "pci";
>> +			linux,pci-domain = <1>;
>> +			bus-range = <0x00 0xff>;
>> +			num-lanes = <2>;
>> +			pipe-clk-source-switch;
> 
> Did you document this property in binding? You need to add "qcom" 
> prefix since
> this is a qcom specific one and not a generic PCI property.
> 
> Thanks,
> Mani
> 

I haven't document this property, missed it in v5. once this change is 
finalized
I will update it next version.

>> +
>> +			#address-cells = <3>;
>> +			#size-cells = <2>;
>> +
>> +			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
>> +				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
>> +
>> +			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "msi";
>> +			#interrupt-cells = <1>;
>> +			interrupt-map-mask = <0 0 0 0x7>;
>> +			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>,
>> +					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>,
>> +					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>,
>> +					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> +			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
>> +				 <&gcc GCC_PCIE_1_PIPE_CLK_SRC>,
>> +				 <&pcie1_lane 0>,
>> +				 <&rpmhcc RPMH_CXO_CLK>,
>> +				 <&gcc GCC_PCIE_1_AUX_CLK>,
>> +				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
>> +				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
>> +				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
>> +				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
>> +				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
>> +				 <&gcc GCC_DDRSS_PCIE_SF_CLK>;
>> +
>> +			clock-names = "pipe",
>> +				      "pipe_mux",
>> +				      "phy_pipe",
>> +				      "ref",
>> +				      "aux",
>> +				      "cfg",
>> +				      "bus_master",
>> +				      "bus_slave",
>> +				      "slave_q2a",
>> +				      "tbu",
>> +				      "ddrss_sf_tbu";
>> +
>> +			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
>> +			assigned-clock-rates = <19200000>;
>> +
>> +			resets = <&gcc GCC_PCIE_1_BCR>;
>> +			reset-names = "pci";
>> +
>> +			power-domains = <&gcc GCC_PCIE_1_GDSC>;
>> +
>> +			phys = <&pcie1_lane>;
>> +			phy-names = "pciephy";
>> +
>> +			perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&pcie1_default_state>;
>> +
>> +			iommus = <&apps_smmu 0x1c80 0x1>;
>> +
>> +			iommu-map = <0x0 &apps_smmu 0x1c80 0x1>,
>> +				    <0x100 &apps_smmu 0x1c81 0x1>;
>> +
>> +			status = "disabled";
>> +		};
>> +
>> +		pcie1_phy: phy@1c0e000 {
>> +			compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy";
>> +			reg = <0 0x01c0e000 0 0x1c0>;
>> +			#address-cells = <2>;
>> +			#size-cells = <2>;
>> +			ranges;
>> +			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
>> +				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
>> +				 <&gcc GCC_PCIE_CLKREF_EN>,
>> +				 <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
>> +			clock-names = "aux", "cfg_ahb", "ref", "refgen";
>> +
>> +			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
>> +			reset-names = "phy";
>> +
>> +			assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
>> +			assigned-clock-rates = <100000000>;
>> +
>> +			status = "disabled";
>> +
>> +			pcie1_lane: lanes@1c0e200 {
>> +				reg = <0 0x01c0e200 0 0x170>,
>> +				      <0 0x01c0e400 0 0x200>,
>> +				      <0 0x01c0ea00 0 0x1f0>,
>> +				      <0 0x01c0e600 0 0x170>,
>> +				      <0 0x01c0e800 0 0x200>,
>> +				      <0 0x01c0ee00 0 0xf4>;
>> +				clocks = <&rpmhcc RPMH_CXO_CLK>;
>> +				clock-names = "pipe0";
>> +
>> +				#phy-cells = <0>;
>> +				#clock-cells = <1>;
>> +				clock-output-names = "pcie_1_pipe_clk";
>> +			};
>> +		};
>> +
>>  		ipa: ipa@1e40000 {
>>  			compatible = "qcom,sc7280-ipa";
>> 
>> @@ -1598,6 +1712,18 @@
>>  					bias-bus-hold;
>>  				};
>>  			};
>> +
>> +			pcie1_default_state: pcie1-default-state {
>> +				clkreq {
>> +					pins = "gpio79";
>> +					function = "pcie1_clkreqn";
>> +				};
>> +
>> +				wake-n {
>> +					pins = "gpio3";
>> +					function = "gpio";
>> +				};
>> +			};
>>  		};
>> 
>>  		apps_smmu: iommu@15000000 {
>> --
>> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora 
>> Forum,
>> a Linux Foundation Collaborative Project
>>