From: Dan Murphy <dmurphy@ti.com>
To: Heiner Kallweit <hkallweit1@gmail.com>, <andrew@lunn.ch>,
<f.fainelli@gmail.com>
Cc: <linux@armlinux.org.uk>, <davem@davemloft.net>,
<netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH net-next v2] net: phy: dp83867: Add speed optimization feature
Date: Thu, 6 Feb 2020 16:36:23 -0600 [thread overview]
Message-ID: <8fa98423-9c3c-62c9-1e5a-29b2eef555e3@ti.com> (raw)
In-Reply-To: <59ce70e0-4404-cade-208d-d089ed238f30@gmail.com>
Heiner
On 2/6/20 4:28 PM, Heiner Kallweit wrote:
> On 06.02.2020 23:13, Dan Murphy wrote:
>> Heiner
>>
>> On 2/5/20 3:16 PM, Heiner Kallweit wrote:
>>> On 04.02.2020 19:13, Dan Murphy wrote:
>>>> Set the speed optimization bit on the DP83867 PHY.
>>>> This feature can also be strapped on the 64 pin PHY devices
>>>> but the 48 pin devices do not have the strap pin available to enable
>>>> this feature in the hardware. PHY team suggests to have this bit set.
>>>>
>>>> With this bit set the PHY will auto negotiate and report the link
>>>> parameters in the PHYSTS register. This register provides a single
>>>> location within the register set for quick access to commonly accessed
>>>> information.
>>>>
>>>> In this case when auto negotiation is on the PHY core reads the bits
>>>> that have been configured or if auto negotiation is off the PHY core
>>>> reads the BMCR register and sets the phydev parameters accordingly.
>>>>
>>>> This Giga bit PHY can throttle the speed to 100Mbps or 10Mbps to accomodate a
>>>> 4-wire cable. If this should occur the PHYSTS register contains the
>>>> current negotiated speed and duplex mode.
>>>>
>>>> In overriding the genphy_read_status the dp83867_read_status will do a
>>>> genphy_read_status to setup the LP and pause bits. And then the PHYSTS
>>>> register is read and the phydev speed and duplex mode settings are
>>>> updated.
>>>>
>>>> Signed-off-by: Dan Murphy <dmurphy@ti.com>
>>>> ---
>>>> v2 - Updated read status to call genphy_read_status first, added link_change
>>>> callback to notify of speed change and use phy_set_bits - https://lore.kernel.org/patchwork/patch/1188348/
>>>>
>>> As stated in the first review, it would be appreciated if you implement
>>> also the downshift tunable. This could be a separate patch in this series.
>>> Most of the implementation would be boilerplate code.
>>
>> I looked at this today and there are no registers that allow tuning the downshift attempts. There is only a RO register that tells you how many attempts it took to achieve a link. So at the very least we could put in the get_tunable but there will be no set.
>>
> The get operation for the downshift tunable should return after how many failed
> attempts the PHY starts a downshift. This doesn't match with your description of
> this register, so yes: Implementing the tunable for this PHY doesn't make sense.
True. This register is only going to return 1,2,4 and 8. And it is
defaulted to 4 attempts.
>
> However this register may be useful in the link_change_notify() callback to
> figure out whether a downshift happened, to trigger the info message you had in
> your first version.
Thats a good idea but.. The register is defaulted to always report 4
attempts were made. It never reports 0 attempts so we would never know
the truth behind the reporting. Kinda like matching the speeds.
Dan
next prev parent reply other threads:[~2020-02-06 22:41 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-02-04 18:13 [PATCH net-next v2] net: phy: dp83867: Add speed optimization feature Dan Murphy
2020-02-04 20:08 ` Heiner Kallweit
2020-02-04 20:30 ` Dan Murphy
2020-02-05 21:16 ` Heiner Kallweit
2020-02-05 21:51 ` Dan Murphy
2020-02-05 22:00 ` Florian Fainelli
2020-02-05 22:01 ` Dan Murphy
2020-02-14 18:32 ` Grygorii Strashko
2020-02-14 18:31 ` Dan Murphy
2020-02-18 14:07 ` Dan Murphy
2020-02-18 16:25 ` Russell King - ARM Linux admin
2020-02-18 16:36 ` Dan Murphy
2020-02-18 16:49 ` Russell King - ARM Linux admin
2020-02-18 17:12 ` Dan Murphy
2020-02-18 17:33 ` Russell King - ARM Linux admin
2020-02-18 17:38 ` Dan Murphy
2020-02-19 0:06 ` Russell King - ARM Linux admin
2020-02-06 22:13 ` Dan Murphy
2020-02-06 22:28 ` Heiner Kallweit
2020-02-06 22:36 ` Dan Murphy [this message]
2020-02-06 23:04 ` Heiner Kallweit
2020-02-06 23:23 ` Dan Murphy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=8fa98423-9c3c-62c9-1e5a-29b2eef555e3@ti.com \
--to=dmurphy@ti.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).