[PATCH V7 1/8] irqchip: add C-SKY SMP interrupt controller

[PATCH V7 1/8] irqchip: add C-SKY SMP interrupt controller

[Guo Ren]

 - Irq-csky-mpintc is C-SKY smp system interrupt controller and it
   could support 16 soft irqs, 16 private irqs, and 992 max common
   irqs.

Changelog:
 - Move IPI_IRQ into the driver
 - Remove irq_set_default_host() and use set_ipi_irq_mapping()
 - Change name with upstream feed-back
 - Change irq map, reserve soft_irq & private_irq space
 - Add License and Copyright
 - Support set_affinity for irq balance in SMP

Signed-off-by: Guo Ren <ren_guo@c-sky.com>
---
 drivers/irqchip/Kconfig           |   8 ++
 drivers/irqchip/Makefile          |   1 +
 drivers/irqchip/irq-csky-mpintc.c | 195 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 204 insertions(+)
 create mode 100644 drivers/irqchip/irq-csky-mpintc.c

diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
index 383e7b7..92e1c20 100644
--- a/drivers/irqchip/Kconfig
+++ b/drivers/irqchip/Kconfig
@@ -371,6 +371,14 @@ config QCOM_PDC
 	  Power Domain Controller driver to manage and configure wakeup
 	  IRQs for Qualcomm Technologies Inc (QTI) mobile chips.
 
+config CSKY_MPINTC
+	bool "C-SKY Multi Processor Interrupt Controller"
+	depends on CSKY
+	help
+	  Say yes here to enable C-SKY SMP interrupt controller driver used
+	  for C-SKY SMP system. In fact it's not mmio map and it use ld/st
+	  to visit the controller's register inside CPU.
+
 endmenu
 
 config SIFIVE_PLIC
diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
index fbd1ec8..6b739ea 100644
--- a/drivers/irqchip/Makefile
+++ b/drivers/irqchip/Makefile
@@ -87,4 +87,5 @@ obj-$(CONFIG_MESON_IRQ_GPIO)		+= irq-meson-gpio.o
 obj-$(CONFIG_GOLDFISH_PIC) 		+= irq-goldfish-pic.o
 obj-$(CONFIG_NDS32)			+= irq-ativic32.o
 obj-$(CONFIG_QCOM_PDC)			+= qcom-pdc.o
+obj-$(CONFIG_CSKY_MPINTC)		+= irq-csky-mpintc.o
 obj-$(CONFIG_SIFIVE_PLIC)		+= irq-sifive-plic.o
diff --git a/drivers/irqchip/irq-csky-mpintc.c b/drivers/irqchip/irq-csky-mpintc.c
new file mode 100644
index 0000000..2b424d27
--- /dev/null
+++ b/drivers/irqchip/irq-csky-mpintc.c
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 Hangzhou C-SKY Microsystems co.,ltd.
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/module.h>
+#include <linux/irqdomain.h>
+#include <linux/irqchip.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+#include <asm/traps.h>
+#include <asm/reg_ops.h>
+#include <asm/smp.h>
+
+static struct irq_domain *root_domain;
+static void __iomem *INTCG_base;
+static void __iomem *INTCL_base;
+
+#define IPI_IRQ		15
+#define INTC_IRQS	256
+#define COMM_IRQ_BASE	32
+
+#define INTCG_SIZE	0x8000
+#define INTCL_SIZE	0x1000
+#define INTC_SIZE	INTCL_SIZE*nr_cpu_ids + INTCG_SIZE
+
+#define INTCG_ICTLR	0x0
+#define INTCG_CICFGR	0x100
+#define INTCG_CIDSTR	0x1000
+
+#define INTCL_PICTLR	0x0
+#define INTCL_SIGR	0x60
+#define INTCL_HPPIR	0x68
+#define INTCL_RDYIR	0x6c
+#define INTCL_SENR	0xa0
+#define INTCL_CENR	0xa4
+#define INTCL_CACR	0xb4
+
+static DEFINE_PER_CPU(void __iomem *, intcl_reg);
+
+static void csky_mpintc_handler(struct pt_regs *regs)
+{
+	void __iomem *reg_base = this_cpu_read(intcl_reg);
+
+	do {
+		handle_domain_irq(root_domain,
+				  readl_relaxed(reg_base + INTCL_RDYIR),
+				  regs);
+	} while (readl_relaxed(reg_base + INTCL_HPPIR) & BIT(31));
+}
+
+static void csky_mpintc_enable(struct irq_data *d)
+{
+	void __iomem *reg_base = this_cpu_read(intcl_reg);
+
+	writel_relaxed(d->hwirq, reg_base + INTCL_SENR);
+}
+
+static void csky_mpintc_disable(struct irq_data *d)
+{
+	void __iomem *reg_base = this_cpu_read(intcl_reg);
+
+	writel_relaxed(d->hwirq, reg_base + INTCL_CENR);
+}
+
+static void csky_mpintc_eoi(struct irq_data *d)
+{
+	void __iomem *reg_base = this_cpu_read(intcl_reg);
+
+	writel_relaxed(d->hwirq, reg_base + INTCL_CACR);
+}
+
+#ifdef CONFIG_SMP
+static int csky_irq_set_affinity(struct irq_data *d,
+				 const struct cpumask *mask_val,
+				 bool force)
+{
+	unsigned int cpu;
+	unsigned int offset = 4 * (d->hwirq - COMM_IRQ_BASE);
+
+	if (!force)
+		cpu = cpumask_any_and(mask_val, cpu_online_mask);
+	else
+		cpu = cpumask_first(mask_val);
+
+	if (cpu >= nr_cpu_ids)
+		return -EINVAL;
+
+	/* Enable interrupt destination */
+	cpu |= BIT(31);
+
+	writel_relaxed(cpu, INTCG_base + INTCG_CIDSTR + offset);
+
+	irq_data_update_effective_affinity(d, cpumask_of(cpu));
+
+	return IRQ_SET_MASK_OK_DONE;
+}
+#endif
+
+static struct irq_chip csky_irq_chip = {
+	.name           = "C-SKY SMP Intc",
+	.irq_eoi	= csky_mpintc_eoi,
+	.irq_enable	= csky_mpintc_enable,
+	.irq_disable	= csky_mpintc_disable,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = csky_irq_set_affinity,
+#endif
+};
+
+static int csky_irqdomain_map(struct irq_domain *d, unsigned int irq,
+			      irq_hw_number_t hwirq)
+{
+	if(hwirq < COMM_IRQ_BASE) {
+		irq_set_percpu_devid(irq);
+		irq_set_chip_and_handler(irq, &csky_irq_chip, handle_percpu_irq);
+	} else {
+		irq_set_chip_and_handler(irq, &csky_irq_chip, handle_fasteoi_irq);
+	}
+
+	return 0;
+}
+
+static const struct irq_domain_ops csky_irqdomain_ops = {
+	.map	= csky_irqdomain_map,
+	.xlate	= irq_domain_xlate_onecell,
+};
+
+#ifdef CONFIG_SMP
+static void csky_mpintc_send_ipi(const unsigned long *mask)
+{
+	void __iomem *reg_base = this_cpu_read(intcl_reg);
+
+	/*
+	 * INTCL_SIGR[3:0] INTID
+	 * INTCL_SIGR[8:15] CPUMASK
+	 */
+	writel_relaxed((*mask) << 8 | IPI_IRQ, reg_base + INTCL_SIGR);
+}
+
+static int csky_mpintc_ipi_irq_mapping(void)
+{
+	return irq_create_mapping(root_domain, IPI_IRQ);
+}
+#endif
+
+/* C-SKY multi processor interrupt controller */
+static int __init
+csky_mpintc_init(struct device_node *node, struct device_node *parent)
+{
+	unsigned int cpu, nr_irq;
+	int ret;
+
+	if (parent)
+		return 0;
+
+	ret = of_property_read_u32(node, "csky,num-irqs", &nr_irq);
+	if (ret < 0)
+		nr_irq = INTC_IRQS;
+
+	if (INTCG_base == NULL) {
+		INTCG_base = ioremap(mfcr("cr<31, 14>"), INTC_SIZE);
+		if (INTCG_base == NULL)
+			return -EIO;
+
+		INTCL_base = INTCG_base + INTCG_SIZE;
+
+		writel_relaxed(BIT(0), INTCG_base + INTCG_ICTLR);
+	}
+
+	root_domain = irq_domain_add_linear(node, nr_irq, &csky_irqdomain_ops,
+					    NULL);
+	if (!root_domain)
+		return -ENXIO;
+
+	/* for every cpu */
+	for_each_present_cpu(cpu) {
+		per_cpu(intcl_reg, cpu) = INTCL_base + (INTCL_SIZE * cpu);
+		writel_relaxed(BIT(0), per_cpu(intcl_reg, cpu) + INTCL_PICTLR);
+	}
+
+	set_handle_irq(&csky_mpintc_handler);
+
+#ifdef CONFIG_SMP
+	set_send_ipi(&csky_mpintc_send_ipi);
+
+	set_ipi_irq_mapping(&csky_mpintc_ipi_irq_mapping);
+#endif
+
+	return 0;
+}
+IRQCHIP_DECLARE(csky_mpintc, "csky,mpintc", csky_mpintc_init);
-- 
2.7.4

[PATCH V7 2/8] dt-bindings: interrupt-controller: C-SKY SMP intc

[Guo Ren]

Dt-bindings doc about C-SKY Multi-processors interrupt controller.

Changelog:
 - Should be: '#interrupt-cells' not 'interrupt-cells'

Signed-off-by: Guo Ren <ren_guo@c-sky.com>
---
 .../bindings/interrupt-controller/csky,mpintc.txt  | 40 ++++++++++++++++++++++
 1 file changed, 40 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt

diff --git a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt
new file mode 100644
index 0000000..ab921f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt
@@ -0,0 +1,40 @@
+===========================================
+C-SKY Multi-processors Interrupt Controller
+===========================================
+
+C-SKY Multi-processors Interrupt Controller is designed for ck807/ck810/ck860
+SMP soc, and it also could be used in non-SMP system.
+
+Interrupt number definition:
+
+  0-15  : software irq, and we use 15 as our IPI_IRQ.
+ 16-31  : private  irq, and we use 16 as the co-processor timer.
+ 31-1024: common irq for soc ip.
+
+=============================
+intc node bindings definition
+=============================
+
+	Description: Describes SMP interrupt controller
+
+	PROPERTIES
+
+	- compatible
+		Usage: required
+		Value type: <string>
+		Definition: must be "csky,mpintc"
+	- #interrupt-cells
+		Usage: required
+		Value type: <u32>
+		Definition: must be <1>
+	- interrupt-controller:
+		Usage: required
+
+Examples:
+---------
+
+	intc: interrupt-controller {
+		compatible = "csky,mpintc";
+		#interrupt-cells = <1>;
+		interrupt-controller;
+	};
-- 
2.7.4

[PATCH V7 3/8] clocksource: add C-SKY SMP timer

[Guo Ren]

This timer is used by SMP system and use mfcr/mtcr instruction
to access the regs.

Changelog:
 - Remove #define CPUHP_AP_CSKY_TIMER_STARTING
 - Add CPUHP_AP_CSKY_TIMER_STARTING in cpuhotplug.h
 - Support csky mp timer alpha version.
 - Just use low-counter with 32bit width as clocksource.
 - Coding convention with upstream feed-back.

Signed-off-by: Guo Ren <ren_guo@c-sky.com>
---
 drivers/clocksource/Kconfig        |   8 ++
 drivers/clocksource/Makefile       |   1 +
 drivers/clocksource/csky_mptimer.c | 176 +++++++++++++++++++++++++++++++++++++
 include/linux/cpuhotplug.h         |   1 +
 4 files changed, 186 insertions(+)
 create mode 100644 drivers/clocksource/csky_mptimer.c

diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index a11f4ba..a28043f 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -620,4 +620,12 @@ config RISCV_TIMER
 	  is accessed via both the SBI and the rdcycle instruction.  This is
 	  required for all RISC-V systems.
 
+config CSKY_MPTIMER
+	bool "C-SKY Multi Processor Timer"
+	depends on CSKY
+	select TIMER_OF
+	help
+	  Say yes here to enable C-SKY SMP timer driver used for C-SKY SMP
+	  system.
+
 endmenu
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index db51b24..848c676 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -79,3 +79,4 @@ obj-$(CONFIG_CLKSRC_ST_LPC)		+= clksrc_st_lpc.o
 obj-$(CONFIG_X86_NUMACHIP)		+= numachip.o
 obj-$(CONFIG_ATCPIT100_TIMER)		+= timer-atcpit100.o
 obj-$(CONFIG_RISCV_TIMER)		+= riscv_timer.o
+obj-$(CONFIG_CSKY_MPTIMER)		+= csky_mptimer.o
diff --git a/drivers/clocksource/csky_mptimer.c b/drivers/clocksource/csky_mptimer.c
new file mode 100644
index 0000000..9dc3cfb
--- /dev/null
+++ b/drivers/clocksource/csky_mptimer.c
@@ -0,0 +1,176 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 Hangzhou C-SKY Microsystems co.,ltd.
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/sched_clock.h>
+#include <linux/cpu.h>
+#include <asm/reg_ops.h>
+
+#include "timer-of.h"
+
+#define PTIM_CCVR	"cr<3, 14>"
+#define PTIM_CTLR	"cr<0, 14>"
+#define PTIM_LVR	"cr<6, 14>"
+#define PTIM_TSR	"cr<1, 14>"
+
+static int csky_mptimer_set_next_event(unsigned long delta, struct clock_event_device *ce)
+{
+	mtcr(PTIM_LVR, delta);
+
+	return 0;
+}
+
+static int csky_mptimer_shutdown(struct clock_event_device *ce)
+{
+	mtcr(PTIM_CTLR, 0);
+
+	return 0;
+}
+
+static int csky_mptimer_oneshot(struct clock_event_device *ce)
+{
+	mtcr(PTIM_CTLR, 1);
+
+	return 0;
+}
+
+static int csky_mptimer_oneshot_stopped(struct clock_event_device *ce)
+{
+	mtcr(PTIM_CTLR, 0);
+
+	return 0;
+}
+
+static DEFINE_PER_CPU(struct timer_of, csky_to) = {
+	.flags					= TIMER_OF_CLOCK,
+	.clkevt = {
+		.rating				= 300,
+		.features			= CLOCK_EVT_FEAT_PERCPU |
+						  CLOCK_EVT_FEAT_ONESHOT,
+		.set_state_shutdown		= csky_mptimer_shutdown,
+		.set_state_oneshot		= csky_mptimer_oneshot,
+		.set_state_oneshot_stopped	= csky_mptimer_oneshot_stopped,
+		.set_next_event			= csky_mptimer_set_next_event,
+	},
+	.of_irq = {
+		.flags				= IRQF_TIMER,
+		.percpu				= 1,
+	},
+};
+
+static irqreturn_t timer_interrupt(int irq, void *dev)
+{
+	struct timer_of *to = this_cpu_ptr(&csky_to);
+
+	mtcr(PTIM_TSR, 0);
+
+	to->clkevt.event_handler(&to->clkevt);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * clock event for percpu
+ */
+static int csky_mptimer_starting_cpu(unsigned int cpu)
+{
+	struct timer_of *to = per_cpu_ptr(&csky_to, cpu);
+
+	to->clkevt.cpumask = cpumask_of(cpu);
+
+	clockevents_config_and_register(&to->clkevt, timer_of_rate(to), 2, ULONG_MAX);
+
+	enable_percpu_irq(timer_of_irq(to), 0);
+
+	return 0;
+}
+
+static int csky_mptimer_dying_cpu(unsigned int cpu)
+{
+	struct timer_of *to = per_cpu_ptr(&csky_to, cpu);
+
+	disable_percpu_irq(timer_of_irq(to));
+
+	return 0;
+}
+
+/*
+ * clock source
+ */
+static u64 sched_clock_read(void)
+{
+	return (u64) mfcr(PTIM_CCVR);
+}
+
+static u64 clksrc_read(struct clocksource *c)
+{
+	return (u64) mfcr(PTIM_CCVR);
+}
+
+struct clocksource csky_clocksource = {
+	.name	= "csky",
+	.rating	= 400,
+	.mask	= CLOCKSOURCE_MASK(32),
+	.flags	= CLOCK_SOURCE_IS_CONTINUOUS,
+	.read	= clksrc_read,
+};
+
+static int __init csky_mptimer_init(struct device_node *np)
+{
+	int ret, cpu;
+	struct timer_of *to;
+	int rate = 0;
+	int irq	 = 0;
+
+	/*
+	 * Csky_mptimer is designed for C-SKY SMP multi-processors and
+	 * every core has it's own private irq and regs for clkevt and
+	 * clksrc.
+	 *
+	 * The regs is accessed by cpu instruction: mfcr/mtcr instead of
+	 * mmio map style. So we needn't mmio-address in dts, but we still
+	 * need to give clk and irq number.
+	 *
+	 * We use private irq for the mptimer and irq number is the same
+	 * for every core. So we use request_percpu_irq() in timer_of_init.
+	 */
+
+	for_each_possible_cpu(cpu) {
+		to = per_cpu_ptr(&csky_to, cpu);
+
+		if (cpu == 0) {
+			to->flags	  |= TIMER_OF_IRQ;
+			to->of_irq.handler = timer_interrupt;
+
+			ret = timer_of_init(np, to);
+			if (ret)
+				return ret;
+
+			rate	= timer_of_rate(to);
+			irq	= to->of_irq.irq;
+		} else {
+			ret = timer_of_init(np, to);
+			if (ret)
+				return ret;
+
+			to->of_clk.rate	= rate;
+			to->of_irq.irq	= irq;
+		}
+	}
+
+	ret = cpuhp_setup_state(CPUHP_AP_CSKY_TIMER_STARTING,
+				"clockevents/csky/timer:starting",
+				csky_mptimer_starting_cpu,
+				csky_mptimer_dying_cpu);
+	if (ret) {
+		pr_err("%s: Failed to cpuhp_setup_state.\n", __func__);
+		return ret;
+	}
+
+	clocksource_register_hz(&csky_clocksource, rate);
+	sched_clock_register(sched_clock_read, 32, rate);
+
+	return 0;
+}
+TIMER_OF_DECLARE(csky_mptimer, "csky,mptimer", csky_mptimer_init);
diff --git a/include/linux/cpuhotplug.h b/include/linux/cpuhotplug.h
index caf40ad..e0cd2ba 100644
--- a/include/linux/cpuhotplug.h
+++ b/include/linux/cpuhotplug.h
@@ -126,6 +126,7 @@ enum cpuhp_state {
 	CPUHP_AP_MIPS_GIC_TIMER_STARTING,
 	CPUHP_AP_ARC_TIMER_STARTING,
 	CPUHP_AP_RISCV_TIMER_STARTING,
+	CPUHP_AP_CSKY_TIMER_STARTING,
 	CPUHP_AP_KVM_STARTING,
 	CPUHP_AP_KVM_ARM_VGIC_INIT_STARTING,
 	CPUHP_AP_KVM_ARM_VGIC_STARTING,
-- 
2.7.4

[PATCH V7 4/8] dt-bindings: timer: C-SKY Multi-processor timer

[Guo Ren]

Dt-bingdings doc for C-SKY SMP system setting.

Changelog:
 - Drop the interrupt-parent.

Signed-off-by: Guo Ren <ren_guo@c-sky.com>
---
 .../devicetree/bindings/timer/csky,mptimer.txt     | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/timer/csky,mptimer.txt

diff --git a/Documentation/devicetree/bindings/timer/csky,mptimer.txt b/Documentation/devicetree/bindings/timer/csky,mptimer.txt
new file mode 100644
index 0000000..15cfec0
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/csky,mptimer.txt
@@ -0,0 +1,42 @@
+============================
+C-SKY Multi-processors Timer
+============================
+
+C-SKY multi-processors timer is designed for C-SKY SMP system and the
+regs is accessed by cpu co-processor 4 registers with mtcr/mfcr.
+
+ - PTIM_CTLR "cr<0, 14>" Control reg to start reset timer.
+ - PTIM_TSR  "cr<1, 14>" Interrupt cleanup status reg.
+ - PTIM_CCVR "cr<3, 14>" Current counter value reg.
+ - PTIM_LVR  "cr<6, 14>" Window value reg to triger next event.
+
+==============================
+timer node bindings definition
+==============================
+
+	Description: Describes SMP timer
+
+	PROPERTIES
+
+	- compatible
+		Usage: required
+		Value type: <string>
+		Definition: must be "csky,mptimer"
+	- clocks
+		Usage: required
+		Value type: <node>
+		Definition: must be input clk node
+	- interrupts
+		Usage: required
+		Value type: <u32>
+		Definition: must be timer irq num defined by soc
+
+Examples:
+---------
+
+	timer: timer {
+		compatible = "csky,mptimer";
+		clocks = <&dummy_apb_clk>;
+		interrupts = <16>;
+		interrupt-parent = <&intc>;
+	};
-- 
2.7.4

[PATCH V7 5/8] dt-bindings: interrupt-controller: C-SKY APB intc

[Guo Ren]

 - Dt-bindings doc about C-SKY apb bus interrupt controller.

Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../interrupt-controller/csky,apb-intc.txt         | 62 ++++++++++++++++++++++
 1 file changed, 62 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/csky,apb-intc.txt

diff --git a/Documentation/devicetree/bindings/interrupt-controller/csky,apb-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/csky,apb-intc.txt
new file mode 100644
index 0000000..44286dc
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/csky,apb-intc.txt
@@ -0,0 +1,62 @@
+==============================
+C-SKY APB Interrupt Controller
+==============================
+
+C-SKY APB Interrupt Controller is a simple soc interrupt controller
+on the apb bus and we only use it as root irq controller.
+
+ - csky,apb-intc is used in a lot of csky fpgas and socs, it support 64 irq nums.
+ - csky,dual-apb-intc consists of 2 apb-intc and 128 irq nums supported.
+ - csky,gx6605s-intc is gx6605s soc internal irq interrupt controller, 64 irq nums.
+
+=============================
+intc node bindings definition
+=============================
+
+	Description: Describes APB interrupt controller
+
+	PROPERTIES
+
+	- compatible
+		Usage: required
+		Value type: <string>
+		Definition: must be "csky,apb-intc"
+				    "csky,dual-apb-intc"
+				    "csky,gx6605s-intc"
+	- #interrupt-cells
+		Usage: required
+		Value type: <u32>
+		Definition: must be <1>
+	- reg
+		Usage: required
+		Value type: <u32 u32>
+		Definition: <phyaddr size> in soc from cpu view
+	- interrupt-controller:
+		Usage: required
+	- csky,support-pulse-signal:
+		Usage: select
+		Description: to support pulse signal flag
+
+Examples:
+---------
+
+	intc: interrupt-controller@500000 {
+		compatible = "csky,apb-intc";
+		#interrupt-cells = <1>;
+		reg = <0x00500000 0x400>;
+		interrupt-controller;
+	};
+
+	intc: interrupt-controller@500000 {
+		compatible = "csky,dual-apb-intc";
+		#interrupt-cells = <1>;
+		reg = <0x00500000 0x400>;
+		interrupt-controller;
+	};
+
+	intc: interrupt-controller@500000 {
+		compatible = "csky,gx6605s-intc";
+		#interrupt-cells = <1>;
+		reg = <0x00500000 0x400>;
+		interrupt-controller;
+	};
-- 
2.7.4

[PATCH V7 6/8] irqchip: add C-SKY APB bus interrupt controller

[Guo Ren]

 - irq-csky-apb-intc is a simple SOC interrupt controller which is
   used in a lot of C-SKY CPU SOC products.

Changelog:
 - use "bool ret" instead of "int ret"
 - add support-pulse-signal in irq-csky-apb-intc.c
 - change name with upstream feed-back
 - add INTC_IFR to clear irq-pending
 - remove CSKY_VECIRQ_LEGENCY
 - change to generic irq chip framework
 - add License and Copyright
 - use irq_domain_add_linear instead of leagcy

Signed-off-by: Guo Ren <ren_guo@c-sky.com>
---
 drivers/irqchip/Kconfig             |   8 ++
 drivers/irqchip/Makefile            |   1 +
 drivers/irqchip/irq-csky-apb-intc.c | 260 ++++++++++++++++++++++++++++++++++++
 3 files changed, 269 insertions(+)
 create mode 100644 drivers/irqchip/irq-csky-apb-intc.c

diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
index 92e1c20..bf12549 100644
--- a/drivers/irqchip/Kconfig
+++ b/drivers/irqchip/Kconfig
@@ -379,6 +379,14 @@ config CSKY_MPINTC
 	  for C-SKY SMP system. In fact it's not mmio map and it use ld/st
 	  to visit the controller's register inside CPU.
 
+config CSKY_APB_INTC
+	bool "C-SKY APB Interrupt Controller"
+	depends on CSKY
+	help
+	  Say yes here to enable C-SKY APB interrupt controller driver used
+	  by C-SKY single core SOC system. It use mmio map apb-bus to visit
+	  the controller's register.
+
 endmenu
 
 config SIFIVE_PLIC
diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
index 6b739ea..72eaf53 100644
--- a/drivers/irqchip/Makefile
+++ b/drivers/irqchip/Makefile
@@ -88,4 +88,5 @@ obj-$(CONFIG_GOLDFISH_PIC) 		+= irq-goldfish-pic.o
 obj-$(CONFIG_NDS32)			+= irq-ativic32.o
 obj-$(CONFIG_QCOM_PDC)			+= qcom-pdc.o
 obj-$(CONFIG_CSKY_MPINTC)		+= irq-csky-mpintc.o
+obj-$(CONFIG_CSKY_APB_INTC)		+= irq-csky-apb-intc.o
 obj-$(CONFIG_SIFIVE_PLIC)		+= irq-sifive-plic.o
diff --git a/drivers/irqchip/irq-csky-apb-intc.c b/drivers/irqchip/irq-csky-apb-intc.c
new file mode 100644
index 0000000..cfe32a7
--- /dev/null
+++ b/drivers/irqchip/irq-csky-apb-intc.c
@@ -0,0 +1,260 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 Hangzhou C-SKY Microsystems co.,ltd.
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/module.h>
+#include <linux/irqdomain.h>
+#include <linux/irqchip.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <asm/irq.h>
+#include <asm/io.h>
+
+#define INTC_IRQS		64
+
+#define CK_INTC_ICR		0x00
+#define CK_INTC_PEN31_00	0x14
+#define CK_INTC_PEN63_32	0x2c
+#define CK_INTC_NEN31_00	0x10
+#define CK_INTC_NEN63_32	0x28
+#define CK_INTC_SOURCE		0x40
+#define CK_INTC_DUAL_BASE	0x100
+
+#define GX_INTC_PEN31_00	0x00
+#define GX_INTC_PEN63_32	0x04
+#define GX_INTC_NEN31_00	0x40
+#define GX_INTC_NEN63_32	0x44
+#define GX_INTC_NMASK31_00	0x50
+#define GX_INTC_NMASK63_32	0x54
+#define GX_INTC_SOURCE		0x60
+
+static void __iomem *reg_base;
+static struct irq_domain *root_domain;
+
+static int nr_irq = INTC_IRQS;
+
+/*
+ * When controller support pulse signal, the PEN_reg will hold on signal
+ * without software trigger.
+ *
+ * So, to support pulse signal we need to clear IFR_reg and the address of
+ * IFR_offset is NEN_offset - 8.
+ */
+static void irq_ck_mask_set_bit(struct irq_data *d)
+{
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+	struct irq_chip_type *ct = irq_data_get_chip_type(d);
+	unsigned long ifr = ct->regs.mask - 8;
+	u32 mask = d->mask;
+
+	irq_gc_lock(gc);
+	*ct->mask_cache |= mask;
+	irq_reg_writel(gc, *ct->mask_cache, ct->regs.mask);
+	irq_reg_writel(gc, irq_reg_readl(gc, ifr) & ~mask, ifr);
+	irq_gc_unlock(gc);
+}
+
+static void __init ck_set_gc(struct device_node *node, void __iomem *reg_base,
+			     u32 mask_reg, u32 irq_base)
+{
+	struct irq_chip_generic *gc;
+
+	gc = irq_get_domain_generic_chip(root_domain, irq_base);
+	gc->reg_base = reg_base;
+	gc->chip_types[0].regs.mask = mask_reg;
+	gc->chip_types[0].chip.irq_mask = irq_gc_mask_clr_bit;
+	gc->chip_types[0].chip.irq_unmask = irq_gc_mask_set_bit;
+
+	if (of_find_property(node, "csky,support-pulse-signal", NULL))
+		gc->chip_types[0].chip.irq_unmask = irq_ck_mask_set_bit;
+}
+
+static inline u32 build_channel_val(u32 idx, u32 magic)
+{
+	u32 res;
+
+	/*
+	 * Set the same index for each channel
+	 */
+	res = idx | (idx << 8) | (idx << 16) | (idx << 24);
+
+	/*
+	 * Set the channel magic number in descending order.
+	 * The magic is 0x00010203 for ck-intc
+	 * The magic is 0x03020100 for gx6605s-intc
+	 */
+	return res | magic;
+}
+
+static inline void setup_irq_channel(u32 magic, void __iomem *reg_addr)
+{
+	u32 i;
+
+	/* Setup 64 channel slots */
+	for (i = 0; i < INTC_IRQS; i += 4) {
+		writel_relaxed(build_channel_val(i, magic), reg_addr + i);
+	}
+}
+
+static int __init
+ck_intc_init_comm(struct device_node *node, struct device_node *parent)
+{
+	int ret;
+
+	if (parent) {
+		pr_err("C-SKY Intc not a root irq controller\n");
+		return -EINVAL;
+	}
+
+	reg_base = of_iomap(node, 0);
+	if (!reg_base) {
+		pr_err("C-SKY Intc unable to map: %p.\n", node);
+		return -EINVAL;
+	}
+
+	root_domain = irq_domain_add_linear(node, nr_irq, &irq_generic_chip_ops, NULL);
+	if (!root_domain) {
+		pr_err("C-SKY Intc irq_domain_add failed.\n");
+		return -ENOMEM;
+	}
+
+	ret = irq_alloc_domain_generic_chips(root_domain, 32, 1,
+					     "csky_intc", handle_level_irq,
+					     IRQ_NOREQUEST | IRQ_NOPROBE | IRQ_NOAUTOEN,
+					     0, 0);
+	if (ret) {
+		pr_err("C-SKY Intc irq_alloc_gc failed.\n");
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static inline bool handle_irq_perbit(struct pt_regs *regs, u32 hwirq, u32 irq_base)
+{
+	u32 irq;
+
+	if (hwirq == 0) return 0;
+
+	while (hwirq) {
+		irq = __ffs(hwirq);
+		hwirq &= ~BIT(irq);
+		handle_domain_irq(root_domain, irq_base + irq, regs);
+	}
+
+	return 1;
+}
+
+/* gx6605s 64 irqs interrupt controller */
+static void gx_irq_handler(struct pt_regs *regs)
+{
+	bool ret;
+
+	do {
+		ret  = handle_irq_perbit(regs ,readl_relaxed(reg_base + GX_INTC_PEN31_00), 0);
+		ret |= handle_irq_perbit(regs ,readl_relaxed(reg_base + GX_INTC_PEN63_32), 32);
+	} while(ret);
+}
+
+static int __init
+gx_intc_init(struct device_node *node, struct device_node *parent)
+{
+	int ret;
+
+	ret = ck_intc_init_comm(node, parent);
+	if (ret)
+		return ret;
+
+	/* Initial enable reg to disable all interrupts */
+	writel_relaxed(0x0, reg_base + GX_INTC_NEN31_00);
+	writel_relaxed(0x0, reg_base + GX_INTC_NEN63_32);
+
+	/* Initial mask reg with all unmasked, becasue we only use enalbe reg */
+	writel_relaxed(0x0, reg_base + GX_INTC_NMASK31_00);
+	writel_relaxed(0x0, reg_base + GX_INTC_NMASK63_32);
+
+	setup_irq_channel(0x03020100, reg_base + GX_INTC_SOURCE);
+
+	ck_set_gc(node, reg_base, GX_INTC_NEN31_00, 0);
+	ck_set_gc(node, reg_base, GX_INTC_NEN63_32, 32);
+
+	set_handle_irq(gx_irq_handler);
+
+	return 0;
+}
+IRQCHIP_DECLARE(csky_gx6605s_intc, "csky,gx6605s-intc", gx_intc_init);
+
+/* C-SKY simple 64 irqs interrupt controller, dual-together could support 128 irqs */
+static void ck_irq_handler(struct pt_regs *regs)
+{
+	bool ret;
+
+	do {
+		/* handle 0 - 31 irqs */
+		ret  = handle_irq_perbit(regs, readl_relaxed(reg_base + CK_INTC_PEN31_00), 0);
+		ret |= handle_irq_perbit(regs, readl_relaxed(reg_base + CK_INTC_PEN63_32), 32);
+
+		if (nr_irq == INTC_IRQS) continue;
+
+		/* handle 64 - 127 irqs */
+		ret |= handle_irq_perbit(regs,
+			   readl_relaxed(reg_base + CK_INTC_PEN31_00 + CK_INTC_DUAL_BASE), 64);
+		ret |= handle_irq_perbit(regs,
+			   readl_relaxed(reg_base + CK_INTC_PEN63_32 + CK_INTC_DUAL_BASE), 96);
+	} while(ret);
+}
+
+static int __init
+ck_intc_init(struct device_node *node, struct device_node *parent)
+{
+	int ret;
+
+	ret = ck_intc_init_comm(node, parent);
+	if (ret)
+		return ret;
+
+	/* Initial enable reg to disable all interrupts */
+	writel_relaxed(0, reg_base + CK_INTC_NEN31_00);
+	writel_relaxed(0, reg_base + CK_INTC_NEN63_32);
+
+	/* Enable irq intc */
+	writel_relaxed(BIT(31), reg_base + CK_INTC_ICR);
+
+	ck_set_gc(node, reg_base, CK_INTC_NEN31_00, 0);
+	ck_set_gc(node, reg_base, CK_INTC_NEN63_32, 32);
+
+	setup_irq_channel(0x00010203, reg_base + CK_INTC_SOURCE);
+
+	set_handle_irq(ck_irq_handler);
+
+	return 0;
+}
+IRQCHIP_DECLARE(ck_intc, "csky,apb-intc", ck_intc_init);
+
+static int __init
+ck_dual_intc_init(struct device_node *node, struct device_node *parent)
+{
+	int ret;
+
+	/* dual-apb-intc up to 128 irq sources*/
+	nr_irq = INTC_IRQS * 2;
+
+	ret = ck_intc_init(node, parent);
+	if (ret)
+		return ret;
+
+	/* Initial enable reg to disable all interrupts */
+	writel_relaxed(0, reg_base + CK_INTC_NEN31_00 + CK_INTC_DUAL_BASE);
+	writel_relaxed(0, reg_base + CK_INTC_NEN63_32 + CK_INTC_DUAL_BASE);
+
+	ck_set_gc(node, reg_base + CK_INTC_DUAL_BASE, CK_INTC_NEN31_00, 64);
+	ck_set_gc(node, reg_base + CK_INTC_DUAL_BASE, CK_INTC_NEN63_32, 96);
+
+	setup_irq_channel(0x00010203, reg_base + CK_INTC_SOURCE + CK_INTC_DUAL_BASE);
+
+	return 0;
+}
+IRQCHIP_DECLARE(ck_dual_intc, "csky,dual-apb-intc", ck_dual_intc_init);
-- 
2.7.4

[PATCH V7 7/8] dt-bindings: timer: gx6605s SOC timer

[Guo Ren]

 - Dt-bindings doc for gx6605s SOC's system timer.

Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/timer/csky,gx6605s-timer.txt          | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/timer/csky,gx6605s-timer.txt

diff --git a/Documentation/devicetree/bindings/timer/csky,gx6605s-timer.txt b/Documentation/devicetree/bindings/timer/csky,gx6605s-timer.txt
new file mode 100644
index 0000000..6b04344
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/csky,gx6605s-timer.txt
@@ -0,0 +1,42 @@
+=================
+gx6605s SOC Timer
+=================
+
+The timer is used in gx6605s soc as system timer and the driver
+contain clk event and clk source.
+
+==============================
+timer node bindings definition
+==============================
+
+	Description: Describes gx6605s SOC timer
+
+	PROPERTIES
+
+	- compatible
+		Usage: required
+		Value type: <string>
+		Definition: must be "csky,gx6605s-timer"
+	- reg
+		Usage: required
+		Value type: <u32 u32>
+		Definition: <phyaddr size> in soc from cpu view
+	- clocks
+		Usage: required
+		Value type: phandle + clock specifier cells
+		Definition: must be input clk node
+	- interrupt
+		Usage: required
+		Value type: <u32>
+		Definition: must be timer irq num defined by soc
+
+Examples:
+---------
+
+	timer0: timer@20a000 {
+		compatible = "csky,gx6605s-timer";
+		reg = <0x0020a000 0x400>;
+		clocks = <&dummy_apb_clk>;
+		interrupts = <10>;
+		interrupt-parent = <&intc>;
+	};
-- 
2.7.4

[PATCH V7 8/8] clocksource: add gx6605s SOC system timer

[Guo Ren]

Changelog:
 - Add License and Copyright
 - Use timer-of framework
 - Change name with upstream feedback
 - Use clksource_mmio framework

Signed-off-by: Guo Ren <ren_guo@c-sky.com>
---
 drivers/clocksource/Kconfig         |   8 ++
 drivers/clocksource/Makefile        |   1 +
 drivers/clocksource/timer-gx6605s.c | 150 ++++++++++++++++++++++++++++++++++++
 3 files changed, 159 insertions(+)
 create mode 100644 drivers/clocksource/timer-gx6605s.c

diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index a28043f..0f38acc 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -628,4 +628,12 @@ config CSKY_MPTIMER
 	  Say yes here to enable C-SKY SMP timer driver used for C-SKY SMP
 	  system.
 
+config GX6605S_TIMER
+	bool "Gx6605s SOC system timer driver"
+	depends on CSKY
+	select CLKSRC_MMIO
+	select TIMER_OF
+	help
+	  This option enables support for gx6605s SOC's timer.
+
 endmenu
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 848c676..7a1b0f4 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -80,3 +80,4 @@ obj-$(CONFIG_X86_NUMACHIP)		+= numachip.o
 obj-$(CONFIG_ATCPIT100_TIMER)		+= timer-atcpit100.o
 obj-$(CONFIG_RISCV_TIMER)		+= riscv_timer.o
 obj-$(CONFIG_CSKY_MPTIMER)		+= csky_mptimer.o
+obj-$(CONFIG_GX6605S_TIMER)		+= timer-gx6605s.o
diff --git a/drivers/clocksource/timer-gx6605s.c b/drivers/clocksource/timer-gx6605s.c
new file mode 100644
index 0000000..10194c9
--- /dev/null
+++ b/drivers/clocksource/timer-gx6605s.c
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 Hangzhou C-SKY Microsystems co.,ltd.
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/sched_clock.h>
+
+#include "timer-of.h"
+
+#define CLKSRC_OFFSET	0x40
+
+#define TIMER_STATUS	0x00
+#define TIMER_VALUE	0x04
+#define TIMER_CONTRL	0x10
+#define TIMER_CONFIG	0x20
+#define TIMER_DIV	0x24
+#define TIMER_INI	0x28
+
+#define GX6605S_STATUS_CLR	BIT(0)
+#define GX6605S_CONTRL_RST	BIT(0)
+#define GX6605S_CONTRL_START	BIT(1)
+#define GX6605S_CONFIG_EN	BIT(0)
+#define GX6605S_CONFIG_IRQ_EN	BIT(1)
+
+static irqreturn_t gx6605s_timer_interrupt(int irq, void *dev)
+{
+	struct clock_event_device *ce = (struct clock_event_device *) dev;
+	void __iomem *base = timer_of_base(to_timer_of(ce));
+
+	writel_relaxed(GX6605S_STATUS_CLR, base + TIMER_STATUS);
+
+	ce->event_handler(ce);
+
+	return IRQ_HANDLED;
+}
+
+static int gx6605s_timer_set_oneshot(struct clock_event_device *ce)
+{
+	void __iomem *base = timer_of_base(to_timer_of(ce));
+
+	/* reset and stop counter */
+	writel_relaxed(GX6605S_CONTRL_RST, base + TIMER_CONTRL);
+
+	/* enable with irq and start */
+	writel_relaxed(GX6605S_CONFIG_EN | GX6605S_CONFIG_IRQ_EN, base + TIMER_CONFIG);
+
+	return 0;
+}
+
+static int gx6605s_timer_set_next_event(unsigned long delta, struct clock_event_device *ce)
+{
+	void __iomem *base = timer_of_base(to_timer_of(ce));
+
+	/* use reset to pause timer */
+	writel_relaxed(GX6605S_CONTRL_RST, base + TIMER_CONTRL);
+
+	/* config next timeout value */
+	writel_relaxed(ULONG_MAX - delta, base + TIMER_INI);
+	writel_relaxed(GX6605S_CONTRL_START, base + TIMER_CONTRL);
+
+	return 0;
+}
+
+static int gx6605s_timer_shutdown(struct clock_event_device *ce)
+{
+	void __iomem *base = timer_of_base(to_timer_of(ce));
+
+	writel_relaxed(0, base + TIMER_CONTRL);
+	writel_relaxed(0, base + TIMER_CONFIG);
+
+	return 0;
+}
+
+static struct timer_of to = {
+	.flags = TIMER_OF_IRQ | TIMER_OF_BASE | TIMER_OF_CLOCK,
+	.clkevt = {
+		.rating			= 300,
+		.features		= CLOCK_EVT_FEAT_DYNIRQ |
+					  CLOCK_EVT_FEAT_ONESHOT,
+		.set_state_shutdown	= gx6605s_timer_shutdown,
+		.set_state_oneshot	= gx6605s_timer_set_oneshot,
+		.set_next_event		= gx6605s_timer_set_next_event,
+		.cpumask		= cpu_possible_mask,
+	},
+	.of_irq = {
+		.handler		= gx6605s_timer_interrupt,
+		.flags			= IRQF_TIMER | IRQF_IRQPOLL,
+	},
+};
+
+static u64 notrace gx6605s_sched_clock_read(void)
+{
+	void __iomem *base;
+
+	base = timer_of_base(&to) + CLKSRC_OFFSET;
+
+	return (u64) readl_relaxed(base + TIMER_VALUE);
+}
+
+static void gx6605s_clkevt_init(void __iomem *base)
+{
+	writel_relaxed(0, base + TIMER_DIV);
+	writel_relaxed(0, base + TIMER_CONFIG);
+
+	clockevents_config_and_register(&to.clkevt, timer_of_rate(&to), 2, ULONG_MAX);
+}
+
+static int gx6605s_clksrc_init(void __iomem *base)
+{
+	writel_relaxed(0, base + TIMER_DIV);
+	writel_relaxed(0, base + TIMER_INI);
+
+	writel_relaxed(GX6605S_CONTRL_RST, base + TIMER_CONTRL);
+
+	writel_relaxed(GX6605S_CONFIG_EN, base + TIMER_CONFIG);
+
+	writel_relaxed(GX6605S_CONTRL_START, base + TIMER_CONTRL);
+
+	sched_clock_register(gx6605s_sched_clock_read, 32, timer_of_rate(&to));
+
+	return clocksource_mmio_init(base + TIMER_VALUE, "gx6605s", timer_of_rate(&to),
+				     200, 32, clocksource_mmio_readl_up);
+}
+
+static int __init gx6605s_timer_init(struct device_node *np)
+{
+	int ret;
+
+	/*
+	 * The timer driver is for nationalchip gx6605s SOC and there are two same timer
+	 * in gx6605s. We use one for clkevt and another for clksrc.
+	 *
+	 * The timer is mmio map to access, so we need give mmio addres in dts.
+	 *
+	 * It provides a 32bit countup timer and interrupt will be caused by count-overflow.
+	 * So we need set-next-event by ULONG_MAX - delta in TIMER_INI reg.
+	 *
+	 * The counter at 0x0  offset is clock event.
+	 * The counter at 0x40 offset is clock source.
+	 * They are the same in hardware, just different used by driver.
+	 */
+	ret = timer_of_init(np, &to);
+	if (ret)
+		return ret;
+
+	gx6605s_clkevt_init(timer_of_base(&to));
+
+	return gx6605s_clksrc_init(timer_of_base(&to) + CLKSRC_OFFSET);
+}
+TIMER_OF_DECLARE(csky_gx6605s_timer, "csky,gx6605s-timer", gx6605s_timer_init);
-- 
2.7.4

Re: [PATCH V7 3/8] clocksource: add C-SKY SMP timer

[Daniel Lezcano]

On 30/09/2018 18:18, Guo Ren wrote:
> This timer is used by SMP system and use mfcr/mtcr instruction
> to access the regs.
> 
> Changelog:
>  - Remove #define CPUHP_AP_CSKY_TIMER_STARTING
>  - Add CPUHP_AP_CSKY_TIMER_STARTING in cpuhotplug.h
>  - Support csky mp timer alpha version.
>  - Just use low-counter with 32bit width as clocksource.
>  - Coding convention with upstream feed-back.
> 
> Signed-off-by: Guo Ren <ren_guo@c-sky.com>
> ---


Guo,

what is the flow of your patches ?

You sent me a V8 with two patches and those timers which I commented.

And now there is this V7 with the patches previously sent as V8 without
the comments take into account.

I'm a bit lost. Can you clarify ?

Thanks

  -- Daniel


-- 
 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

Re: [PATCH V7 3/8] clocksource: add C-SKY SMP timer

[Guo Ren]

On Sun, Sep 30, 2018 at 09:22:30PM +0200, Daniel Lezcano wrote:
> On 30/09/2018 18:18, Guo Ren wrote:
> > This timer is used by SMP system and use mfcr/mtcr instruction
> > to access the regs.
> > 
> > Changelog:
> >  - Remove #define CPUHP_AP_CSKY_TIMER_STARTING
> >  - Add CPUHP_AP_CSKY_TIMER_STARTING in cpuhotplug.h
> >  - Support csky mp timer alpha version.
> >  - Just use low-counter with 32bit width as clocksource.
> >  - Coding convention with upstream feed-back.
> > 
> > Signed-off-by: Guo Ren <ren_guo@c-sky.com>
> > ---
> 
> 
> Guo,
> 
> what is the flow of your patches ?
> 
> You sent me a V8 with two patches and those timers which I commented.
> 
> And now there is this V7 with the patches previously sent as V8 without
> the comments take into account.
> 
> I'm a bit lost. Can you clarify ?
Opps ... I should send the "V9 C-SKY(csky) Linux Drivers". It's a wrong
patchset from "V6 C-SKY(csky) Linux Kernel Port".

The patchset didn't include your comment in V8:
 - Add COMIPLE_TEST in Kconfig
 - no cast is needed for "struct clock_event_device *ce = dev"
 - remove: extra space after (u64).

I'm sorry about it, I'll send "V9 C-SKY(csky) Linux Drivers". My fault.

Best Regards
 Guo Ren