* [PATCH v5 1/6] nvmem: add driver for JZ4780 efuse
2020-02-22 10:25 [PATCH v5 0/6] MIPS: CI20: Add efuse driver for Ingenic JZ4780 and attach to DM9000 for stable MAC addresses H. Nikolaus Schaller
@ 2020-02-22 10:25 ` H. Nikolaus Schaller
2020-02-22 15:38 ` Paul Cercueil
2020-02-22 10:25 ` [PATCH v5 2/6] Bindings: nvmem: add bindings " H. Nikolaus Schaller
` (4 subsequent siblings)
5 siblings, 1 reply; 17+ messages in thread
From: H. Nikolaus Schaller @ 2020-02-22 10:25 UTC (permalink / raw)
To: PrasannaKumar Muralidharan, Andreas Kemnade, Paul Cercueil,
Mathieu Malaterre, Srinivas Kandagatla, Rob Herring,
Mark Rutland, Ralf Baechle, Paul Burton, Mauro Carvalho Chehab,
David S. Miller, Greg Kroah-Hartman, Jonathan Cameron,
H. Nikolaus Schaller, Krzysztof Kozlowski, Kees Cook, Andi Kleen,
Geert Uytterhoeven
Cc: linux-kernel, devicetree, linux-mips, letux-kernel, kernel
From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory and nvmem cells.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
drivers/nvmem/Kconfig | 10 ++
drivers/nvmem/Makefile | 2 +
drivers/nvmem/jz4780-efuse.c | 229 +++++++++++++++++++++++++++++++++++
3 files changed, 241 insertions(+)
create mode 100644 drivers/nvmem/jz4780-efuse.c
diff --git a/drivers/nvmem/Kconfig b/drivers/nvmem/Kconfig
index 35efab1ba8d9..8143e6e1dd82 100644
--- a/drivers/nvmem/Kconfig
+++ b/drivers/nvmem/Kconfig
@@ -55,6 +55,16 @@ config NVMEM_IMX_OCOTP_SCU
This is a driver for the SCU On-Chip OTP Controller (OCOTP)
available on i.MX8 SoCs.
+config JZ4780_EFUSE
+ tristate "JZ4780 EFUSE Memory Support"
+ depends on MACH_INGENIC || COMPILE_TEST
+ depends on HAS_IOMEM
+ help
+ Say Y here to include support for JZ4780 efuse memory found on
+ all JZ4780 SoC based devices.
+ To compile this driver as a module, choose M here: the module
+ will be called nvmem_jz4780_efuse.
+
config NVMEM_LPC18XX_EEPROM
tristate "NXP LPC18XX EEPROM Memory Support"
depends on ARCH_LPC18XX || COMPILE_TEST
diff --git a/drivers/nvmem/Makefile b/drivers/nvmem/Makefile
index 6b466cd1427b..65a268d17807 100644
--- a/drivers/nvmem/Makefile
+++ b/drivers/nvmem/Makefile
@@ -18,6 +18,8 @@ obj-$(CONFIG_NVMEM_IMX_OCOTP) += nvmem-imx-ocotp.o
nvmem-imx-ocotp-y := imx-ocotp.o
obj-$(CONFIG_NVMEM_IMX_OCOTP_SCU) += nvmem-imx-ocotp-scu.o
nvmem-imx-ocotp-scu-y := imx-ocotp-scu.o
+obj-$(CONFIG_JZ4780_EFUSE) += nvmem_jz4780_efuse.o
+nvmem_jz4780_efuse-y := jz4780-efuse.o
obj-$(CONFIG_NVMEM_LPC18XX_EEPROM) += nvmem_lpc18xx_eeprom.o
nvmem_lpc18xx_eeprom-y := lpc18xx_eeprom.o
obj-$(CONFIG_NVMEM_LPC18XX_OTP) += nvmem_lpc18xx_otp.o
diff --git a/drivers/nvmem/jz4780-efuse.c b/drivers/nvmem/jz4780-efuse.c
new file mode 100644
index 000000000000..08b63de0e9cc
--- /dev/null
+++ b/drivers/nvmem/jz4780-efuse.c
@@ -0,0 +1,229 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * JZ4780 EFUSE Memory Support driver
+ *
+ * Copyright (c) 2017 PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
+ * Copyright (c) 2020 H. Nikolaus Schaller <hns@goldelico.com>
+ */
+
+/*
+ * Currently supports JZ4780 efuse which has 8K programmable bit.
+ * Efuse is separated into seven segments as below:
+ *
+ * -----------------------------------------------------------------------
+ * | 64 bit | 128 bit | 128 bit | 3520 bit | 8 bit | 2296 bit | 2048 bit |
+ * -----------------------------------------------------------------------
+ *
+ * The rom itself is accessed using a 9 bit address line and an 8 word wide bus
+ * which reads/writes based on strobes. The strobe is configured in the config
+ * register and is based on number of cycles of the bus clock.
+ *
+ * Driver supports read only as the writes are done in the Factory.
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/nvmem-provider.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/timer.h>
+
+#define JZ_EFUCTRL (0x0) /* Control Register */
+#define JZ_EFUCFG (0x4) /* Configure Register*/
+#define JZ_EFUSTATE (0x8) /* Status Register */
+#define JZ_EFUDATA(n) (0xC + (n) * 4)
+
+#define EFUCTRL_ADDR_MASK 0x3FF
+#define EFUCTRL_ADDR_SHIFT 21
+#define EFUCTRL_LEN_MASK 0x1F
+#define EFUCTRL_LEN_SHIFT 16
+#define EFUCTRL_PG_EN BIT(15)
+#define EFUCTRL_WR_EN BIT(1)
+#define EFUCTRL_RD_EN BIT(0)
+
+#define EFUCFG_INT_EN BIT(31)
+#define EFUCFG_RD_ADJ_MASK 0xF
+#define EFUCFG_RD_ADJ_SHIFT 20
+#define EFUCFG_RD_STR_MASK 0xF
+#define EFUCFG_RD_STR_SHIFT 16
+#define EFUCFG_WR_ADJ_MASK 0xF
+#define EFUCFG_WR_ADJ_SHIFT 12
+#define EFUCFG_WR_STR_MASK 0xFFF
+#define EFUCFG_WR_STR_SHIFT 0
+
+#define EFUSTATE_WR_DONE BIT(1)
+#define EFUSTATE_RD_DONE BIT(0)
+
+struct jz4780_efuse {
+ struct device *dev;
+ struct regmap *map;
+ struct clk *clk;
+ unsigned int rd_adj;
+ unsigned int rd_strobe;
+};
+
+/* We read 32 byte chunks to avoid complexity in the driver. */
+static int jz4780_efuse_read_32bytes(struct jz4780_efuse *efuse, char *buf,
+ unsigned int addr)
+{
+ unsigned int tmp;
+ u32 ctrl;
+ int ret;
+ const int size = 32;
+
+ ctrl = (addr << EFUCTRL_ADDR_SHIFT)
+ | ((size - 1) << EFUCTRL_LEN_SHIFT)
+ | EFUCTRL_RD_EN;
+
+ regmap_update_bits(efuse->map, JZ_EFUCTRL,
+ (EFUCTRL_ADDR_MASK << EFUCTRL_ADDR_SHIFT) |
+ (EFUCTRL_LEN_MASK << EFUCTRL_LEN_SHIFT) |
+ EFUCTRL_PG_EN | EFUCTRL_WR_EN | EFUCTRL_RD_EN, ctrl);
+
+ ret = regmap_read_poll_timeout(efuse->map, JZ_EFUSTATE,
+ tmp, tmp & EFUSTATE_RD_DONE,
+ 1 * MSEC_PER_SEC, 50 * MSEC_PER_SEC);
+ if (ret < 0) {
+ dev_err(efuse->dev, "Time out while reading efuse data");
+ return ret;
+ }
+
+ return regmap_bulk_read(efuse->map, JZ_EFUDATA(0),
+ buf, size / sizeof(u32));
+}
+
+/* main entry point */
+static int jz4780_efuse_read(void *context, unsigned int offset,
+ void *val, size_t bytes)
+{
+ struct jz4780_efuse *efuse = context;
+ int ret;
+ const int size = 32;
+
+ while (bytes > 0) {
+ unsigned int start = offset & ~(size - 1);
+ unsigned int chunk = min(bytes, (start + size) - offset);
+
+ if (start == offset && chunk == size) {
+ ret = jz4780_efuse_read_32bytes(efuse, val, start);
+ if (ret < 0)
+ return ret;
+
+ } else {
+ char buf[32];
+
+ ret = jz4780_efuse_read_32bytes(efuse, buf, start);
+ if (ret < 0)
+ return ret;
+
+ memcpy(val, &buf[offset - start], chunk);
+ }
+
+ val += chunk;
+ offset += chunk;
+ bytes -= chunk;
+ }
+
+ return 0;
+}
+
+static struct nvmem_config jz4780_efuse_nvmem_config __initdata = {
+ .name = "jz4780-efuse",
+ .size = 1024,
+ .word_size = 1,
+ .stride = 1,
+ .owner = THIS_MODULE,
+ .reg_read = jz4780_efuse_read,
+};
+
+static const struct regmap_config jz4780_efuse_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = JZ_EFUDATA(7),
+};
+
+static int jz4780_efuse_probe(struct platform_device *pdev)
+{
+ struct nvmem_device *nvmem;
+ struct jz4780_efuse *efuse;
+ struct nvmem_config cfg;
+ unsigned long clk_rate;
+ struct device *dev = &pdev->dev;
+ void __iomem *regs;
+
+ efuse = devm_kzalloc(dev, sizeof(*efuse), GFP_KERNEL);
+ if (!efuse)
+ return -ENOMEM;
+
+ regs = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(regs))
+ return PTR_ERR(regs);
+
+ efuse->map = devm_regmap_init_mmio(dev, regs,
+ &jz4780_efuse_regmap_config);
+ if (IS_ERR(efuse->map))
+ return PTR_ERR(efuse->map);
+
+ efuse->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(efuse->clk))
+ return PTR_ERR(efuse->clk);
+
+ clk_rate = clk_get_rate(efuse->clk);
+
+ efuse->dev = dev;
+ /*
+ * rd_adj and rd_strobe are 4 bit values
+ * bus clk period * (rd_adj + 1) > 6.5ns
+ * bus clk period * (rd_adj + 5 + rd_strobe) > 35ns
+ */
+ efuse->rd_adj = (((6500 * (clk_rate / 1000000)) / 1000000) + 1) - 1;
+ efuse->rd_strobe = ((((35000 * (clk_rate / 1000000)) / 1000000) + 1)
+ - 5 - efuse->rd_adj);
+
+ if (efuse->rd_adj > 0x1F || efuse->rd_strobe > 0x1F) {
+ dev_err(&pdev->dev, "Cannot set clock configuration\n");
+ return -EINVAL;
+ }
+
+ regmap_update_bits(efuse->map, JZ_EFUCFG,
+ (EFUCFG_RD_ADJ_MASK << EFUCFG_RD_ADJ_SHIFT) |
+ (EFUCFG_RD_STR_MASK << EFUCFG_RD_STR_SHIFT),
+ (efuse->rd_adj << EFUCFG_RD_ADJ_SHIFT) |
+ (efuse->rd_strobe << EFUCFG_RD_STR_SHIFT));
+
+ cfg = jz4780_efuse_nvmem_config;
+ cfg.dev = &pdev->dev;
+ cfg.priv = efuse;
+
+ nvmem = devm_nvmem_register(dev, &cfg);
+ if (IS_ERR(nvmem))
+ return PTR_ERR(nvmem);
+
+ platform_set_drvdata(pdev, nvmem);
+
+ return 0;
+}
+
+static const struct of_device_id jz4780_efuse_match[] = {
+ { .compatible = "ingenic,jz4780-efuse" },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, jz4780_efuse_match);
+
+static struct platform_driver jz4780_efuse_driver = {
+ .probe = jz4780_efuse_probe,
+ .driver = {
+ .name = "jz4780-efuse",
+ .of_match_table = jz4780_efuse_match,
+ },
+};
+module_platform_driver(jz4780_efuse_driver);
+
+MODULE_AUTHOR("PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>");
+MODULE_AUTHOR("H. Nikolaus Schaller <hns@goldelico.com>");
+MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
+MODULE_DESCRIPTION("Ingenic JZ4780 efuse driver");
+MODULE_LICENSE("GPL v2");
--
2.23.0
^ permalink raw reply related [flat|nested] 17+ messages in thread* Re: [PATCH v5 1/6] nvmem: add driver for JZ4780 efuse
2020-02-22 10:25 ` [PATCH v5 1/6] nvmem: add driver for JZ4780 efuse H. Nikolaus Schaller
@ 2020-02-22 15:38 ` Paul Cercueil
2020-02-22 17:16 ` H. Nikolaus Schaller
0 siblings, 1 reply; 17+ messages in thread
From: Paul Cercueil @ 2020-02-22 15:38 UTC (permalink / raw)
To: H. Nikolaus Schaller
Cc: PrasannaKumar Muralidharan, Andreas Kemnade, Mathieu Malaterre,
Srinivas Kandagatla, Rob Herring, Mark Rutland, Ralf Baechle,
Paul Burton, Mauro Carvalho Chehab, David S. Miller,
Greg Kroah-Hartman, Jonathan Cameron, Krzysztof Kozlowski,
Kees Cook, Andi Kleen, Geert Uytterhoeven, linux-kernel,
devicetree, linux-mips, letux-kernel, kernel
Hi Nikolaus,
Le sam., févr. 22, 2020 at 11:25, H. Nikolaus Schaller
<hns@goldelico.com> a écrit :
> From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>
> This patch brings support for the JZ4780 efuse. Currently it only
> exposes
> a read only access to the entire 8K bits efuse memory and nvmem cells.
>
> Tested-by: Mathieu Malaterre <malat@debian.org>
> Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> Signed-off-by: Mathieu Malaterre <malat@debian.org>
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> ---
> drivers/nvmem/Kconfig | 10 ++
> drivers/nvmem/Makefile | 2 +
> drivers/nvmem/jz4780-efuse.c | 229
> +++++++++++++++++++++++++++++++++++
> 3 files changed, 241 insertions(+)
> create mode 100644 drivers/nvmem/jz4780-efuse.c
>
> diff --git a/drivers/nvmem/Kconfig b/drivers/nvmem/Kconfig
> index 35efab1ba8d9..8143e6e1dd82 100644
> --- a/drivers/nvmem/Kconfig
> +++ b/drivers/nvmem/Kconfig
> @@ -55,6 +55,16 @@ config NVMEM_IMX_OCOTP_SCU
> This is a driver for the SCU On-Chip OTP Controller (OCOTP)
> available on i.MX8 SoCs.
>
> +config JZ4780_EFUSE
> + tristate "JZ4780 EFUSE Memory Support"
> + depends on MACH_INGENIC || COMPILE_TEST
> + depends on HAS_IOMEM
You're using regmap, so you need to select REGMAP_MMIO here.
> + help
> + Say Y here to include support for JZ4780 efuse memory found on
> + all JZ4780 SoC based devices.
> + To compile this driver as a module, choose M here: the module
> + will be called nvmem_jz4780_efuse.
> +
> config NVMEM_LPC18XX_EEPROM
> tristate "NXP LPC18XX EEPROM Memory Support"
> depends on ARCH_LPC18XX || COMPILE_TEST
> diff --git a/drivers/nvmem/Makefile b/drivers/nvmem/Makefile
> index 6b466cd1427b..65a268d17807 100644
> --- a/drivers/nvmem/Makefile
> +++ b/drivers/nvmem/Makefile
> @@ -18,6 +18,8 @@ obj-$(CONFIG_NVMEM_IMX_OCOTP) += nvmem-imx-ocotp.o
> nvmem-imx-ocotp-y := imx-ocotp.o
> obj-$(CONFIG_NVMEM_IMX_OCOTP_SCU) += nvmem-imx-ocotp-scu.o
> nvmem-imx-ocotp-scu-y := imx-ocotp-scu.o
> +obj-$(CONFIG_JZ4780_EFUSE) += nvmem_jz4780_efuse.o
> +nvmem_jz4780_efuse-y := jz4780-efuse.o
> obj-$(CONFIG_NVMEM_LPC18XX_EEPROM) += nvmem_lpc18xx_eeprom.o
> nvmem_lpc18xx_eeprom-y := lpc18xx_eeprom.o
> obj-$(CONFIG_NVMEM_LPC18XX_OTP) += nvmem_lpc18xx_otp.o
> diff --git a/drivers/nvmem/jz4780-efuse.c
> b/drivers/nvmem/jz4780-efuse.c
> new file mode 100644
> index 000000000000..08b63de0e9cc
> --- /dev/null
> +++ b/drivers/nvmem/jz4780-efuse.c
> @@ -0,0 +1,229 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * JZ4780 EFUSE Memory Support driver
> + *
> + * Copyright (c) 2017 PrasannaKumar Muralidharan
> <prasannatsmkumar@gmail.com>
> + * Copyright (c) 2020 H. Nikolaus Schaller <hns@goldelico.com>
> + */
> +
> +/*
> + * Currently supports JZ4780 efuse which has 8K programmable bit.
> + * Efuse is separated into seven segments as below:
> + *
> + *
> -----------------------------------------------------------------------
> + * | 64 bit | 128 bit | 128 bit | 3520 bit | 8 bit | 2296 bit | 2048
> bit |
> + *
> -----------------------------------------------------------------------
> + *
> + * The rom itself is accessed using a 9 bit address line and an 8
> word wide bus
> + * which reads/writes based on strobes. The strobe is configured in
> the config
> + * register and is based on number of cycles of the bus clock.
> + *
> + * Driver supports read only as the writes are done in the Factory.
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/clk.h>
> +#include <linux/module.h>
> +#include <linux/nvmem-provider.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/timer.h>
> +
> +#define JZ_EFUCTRL (0x0) /* Control Register */
> +#define JZ_EFUCFG (0x4) /* Configure Register*/
> +#define JZ_EFUSTATE (0x8) /* Status Register */
> +#define JZ_EFUDATA(n) (0xC + (n) * 4)
> +
> +#define EFUCTRL_ADDR_MASK 0x3FF
> +#define EFUCTRL_ADDR_SHIFT 21
> +#define EFUCTRL_LEN_MASK 0x1F
> +#define EFUCTRL_LEN_SHIFT 16
> +#define EFUCTRL_PG_EN BIT(15)
> +#define EFUCTRL_WR_EN BIT(1)
> +#define EFUCTRL_RD_EN BIT(0)
> +
> +#define EFUCFG_INT_EN BIT(31)
> +#define EFUCFG_RD_ADJ_MASK 0xF
> +#define EFUCFG_RD_ADJ_SHIFT 20
> +#define EFUCFG_RD_STR_MASK 0xF
> +#define EFUCFG_RD_STR_SHIFT 16
> +#define EFUCFG_WR_ADJ_MASK 0xF
> +#define EFUCFG_WR_ADJ_SHIFT 12
> +#define EFUCFG_WR_STR_MASK 0xFFF
> +#define EFUCFG_WR_STR_SHIFT 0
> +
> +#define EFUSTATE_WR_DONE BIT(1)
> +#define EFUSTATE_RD_DONE BIT(0)
> +
> +struct jz4780_efuse {
> + struct device *dev;
> + struct regmap *map;
> + struct clk *clk;
> + unsigned int rd_adj;
> + unsigned int rd_strobe;
> +};
> +
> +/* We read 32 byte chunks to avoid complexity in the driver. */
I don't see how reading 32 byte chunks avoids complexity in the driver;
the 'size' variable here could very well be an argument.
> +static int jz4780_efuse_read_32bytes(struct jz4780_efuse *efuse,
> char *buf,
> + unsigned int addr)
> +{
> + unsigned int tmp;
> + u32 ctrl;
> + int ret;
> + const int size = 32;
> +
> + ctrl = (addr << EFUCTRL_ADDR_SHIFT)
> + | ((size - 1) << EFUCTRL_LEN_SHIFT)
> + | EFUCTRL_RD_EN;
> +
> + regmap_update_bits(efuse->map, JZ_EFUCTRL,
> + (EFUCTRL_ADDR_MASK << EFUCTRL_ADDR_SHIFT) |
> + (EFUCTRL_LEN_MASK << EFUCTRL_LEN_SHIFT) |
> + EFUCTRL_PG_EN | EFUCTRL_WR_EN | EFUCTRL_RD_EN, ctrl);
> +
> + ret = regmap_read_poll_timeout(efuse->map, JZ_EFUSTATE,
> + tmp, tmp & EFUSTATE_RD_DONE,
> + 1 * MSEC_PER_SEC, 50 * MSEC_PER_SEC);
> + if (ret < 0) {
> + dev_err(efuse->dev, "Time out while reading efuse data");
> + return ret;
> + }
> +
> + return regmap_bulk_read(efuse->map, JZ_EFUDATA(0),
> + buf, size / sizeof(u32));
> +}
> +
> +/* main entry point */
> +static int jz4780_efuse_read(void *context, unsigned int offset,
> + void *val, size_t bytes)
> +{
> + struct jz4780_efuse *efuse = context;
> + int ret;
> + const int size = 32;
> +
> + while (bytes > 0) {
> + unsigned int start = offset & ~(size - 1);
> + unsigned int chunk = min(bytes, (start + size) - offset);
Why do you need to check for the address alignment?
> +
> + if (start == offset && chunk == size) {
> + ret = jz4780_efuse_read_32bytes(efuse, val, start);
> + if (ret < 0)
> + return ret;
> +
> + } else {
> + char buf[32];
> +
> + ret = jz4780_efuse_read_32bytes(efuse, buf, start);
> + if (ret < 0)
> + return ret;
> +
> + memcpy(val, &buf[offset - start], chunk);
Why do you need this cumbersome process of reading 32 bytes if you need
less than that? This looks over-complex to me.
> + }
> +
> + val += chunk;
> + offset += chunk;
> + bytes -= chunk;
> + }
> +
> + return 0;
> +}
> +
> +static struct nvmem_config jz4780_efuse_nvmem_config __initdata = {
> + .name = "jz4780-efuse",
> + .size = 1024,
The efuse is 8 KiB.
> + .word_size = 1,
> + .stride = 1,
> + .owner = THIS_MODULE,
> + .reg_read = jz4780_efuse_read,
> +};
> +
> +static const struct regmap_config jz4780_efuse_regmap_config = {
> + .reg_bits = 32,
> + .val_bits = 32,
> + .reg_stride = 4,
> + .max_register = JZ_EFUDATA(7),
> +};
> +
> +static int jz4780_efuse_probe(struct platform_device *pdev)
> +{
> + struct nvmem_device *nvmem;
> + struct jz4780_efuse *efuse;
> + struct nvmem_config cfg;
> + unsigned long clk_rate;
> + struct device *dev = &pdev->dev;
> + void __iomem *regs;
> +
> + efuse = devm_kzalloc(dev, sizeof(*efuse), GFP_KERNEL);
> + if (!efuse)
> + return -ENOMEM;
> +
> + regs = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(regs))
> + return PTR_ERR(regs);
> +
> + efuse->map = devm_regmap_init_mmio(dev, regs,
> + &jz4780_efuse_regmap_config);
> + if (IS_ERR(efuse->map))
> + return PTR_ERR(efuse->map);
> +
> + efuse->clk = devm_clk_get(&pdev->dev, NULL);
> + if (IS_ERR(efuse->clk))
> + return PTR_ERR(efuse->clk);
> +
> + clk_rate = clk_get_rate(efuse->clk);
You didn't enable the clock before, so clk_get_rate can return a bogus
value.
> +
> + efuse->dev = dev;
> + /*
> + * rd_adj and rd_strobe are 4 bit values
> + * bus clk period * (rd_adj + 1) > 6.5ns
> + * bus clk period * (rd_adj + 5 + rd_strobe) > 35ns
> + */
> + efuse->rd_adj = (((6500 * (clk_rate / 1000000)) / 1000000) + 1) - 1;
I can't get my head around this calculus. Try this:
/* 1 / 6.5ns == 153846154 Hz */
efuse->rd_adj = clk_rate / 153846154;
The efuse read should be *at least* 6.5ns, so no need to bother with
the -1/+1.
> + efuse->rd_strobe = ((((35000 * (clk_rate / 1000000)) / 1000000) + 1)
> + - 5 - efuse->rd_adj);
/* 1 / 35ns == 28571429 Hz */
efuse->rd_strobe = max(0, clk_rate / 28571429 + 1 - 5 - efuse->rd_adj);
> +
> + if (efuse->rd_adj > 0x1F || efuse->rd_strobe > 0x1F) {
> + dev_err(&pdev->dev, "Cannot set clock configuration\n");
> + return -EINVAL;
> + }
> +
> + regmap_update_bits(efuse->map, JZ_EFUCFG,
> + (EFUCFG_RD_ADJ_MASK << EFUCFG_RD_ADJ_SHIFT) |
> + (EFUCFG_RD_STR_MASK << EFUCFG_RD_STR_SHIFT),
> + (efuse->rd_adj << EFUCFG_RD_ADJ_SHIFT) |
> + (efuse->rd_strobe << EFUCFG_RD_STR_SHIFT));
> +
> + cfg = jz4780_efuse_nvmem_config;
> + cfg.dev = &pdev->dev;
> + cfg.priv = efuse;
> +
> + nvmem = devm_nvmem_register(dev, &cfg);
> + if (IS_ERR(nvmem))
> + return PTR_ERR(nvmem);
> +
> + platform_set_drvdata(pdev, nvmem);
This isn't used anywhere.
> +
> + return 0;
> +}
> +
> +static const struct of_device_id jz4780_efuse_match[] = {
> + { .compatible = "ingenic,jz4780-efuse" },
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, jz4780_efuse_match);
> +
> +static struct platform_driver jz4780_efuse_driver = {
> + .probe = jz4780_efuse_probe,
> + .driver = {
> + .name = "jz4780-efuse",
> + .of_match_table = jz4780_efuse_match,
> + },
> +};
> +module_platform_driver(jz4780_efuse_driver);
> +
> +MODULE_AUTHOR("PrasannaKumar Muralidharan
> <prasannatsmkumar@gmail.com>");
> +MODULE_AUTHOR("H. Nikolaus Schaller <hns@goldelico.com>");
> +MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
> +MODULE_DESCRIPTION("Ingenic JZ4780 efuse driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.23.0
>
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH v5 1/6] nvmem: add driver for JZ4780 efuse
2020-02-22 15:38 ` Paul Cercueil
@ 2020-02-22 17:16 ` H. Nikolaus Schaller
2020-02-22 18:13 ` Paul Cercueil
0 siblings, 1 reply; 17+ messages in thread
From: H. Nikolaus Schaller @ 2020-02-22 17:16 UTC (permalink / raw)
To: Paul Cercueil
Cc: PrasannaKumar Muralidharan, Andreas Kemnade, Mathieu Malaterre,
Srinivas Kandagatla, Rob Herring, Mark Rutland, Ralf Baechle,
Paul Burton, Mauro Carvalho Chehab, David S. Miller,
Greg Kroah-Hartman, Jonathan Cameron, Krzysztof Kozlowski,
Kees Cook, Andi Kleen, Geert Uytterhoeven, linux-kernel,
devicetree, linux-mips, letux-kernel, kernel
Hi Paul,
> Am 22.02.2020 um 16:38 schrieb Paul Cercueil <paul@crapouillou.net>:
>
> Hi Nikolaus,
>
>
> Le sam., févr. 22, 2020 at 11:25, H. Nikolaus Schaller <hns@goldelico.com> a écrit :
>> From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>> This patch brings support for the JZ4780 efuse. Currently it only exposes
>> a read only access to the entire 8K bits efuse memory and nvmem cells.
>> Tested-by: Mathieu Malaterre <malat@debian.org>
>> Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>> Signed-off-by: Mathieu Malaterre <malat@debian.org>
>> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
>> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
>> ---
>> drivers/nvmem/Kconfig | 10 ++
>> drivers/nvmem/Makefile | 2 +
>> drivers/nvmem/jz4780-efuse.c | 229 +++++++++++++++++++++++++++++++++++
>> 3 files changed, 241 insertions(+)
>> create mode 100644 drivers/nvmem/jz4780-efuse.c
>> diff --git a/drivers/nvmem/Kconfig b/drivers/nvmem/Kconfig
>> index 35efab1ba8d9..8143e6e1dd82 100644
>> --- a/drivers/nvmem/Kconfig
>> +++ b/drivers/nvmem/Kconfig
>> @@ -55,6 +55,16 @@ config NVMEM_IMX_OCOTP_SCU
>> This is a driver for the SCU On-Chip OTP Controller (OCOTP)
>> available on i.MX8 SoCs.
>> +config JZ4780_EFUSE
>> + tristate "JZ4780 EFUSE Memory Support"
>> + depends on MACH_INGENIC || COMPILE_TEST
>> + depends on HAS_IOMEM
>
> You're using regmap, so you need to select REGMAP_MMIO here.
Ok.
>
>> + help
>> + Say Y here to include support for JZ4780 efuse memory found on
>> + all JZ4780 SoC based devices.
>> + To compile this driver as a module, choose M here: the module
>> + will be called nvmem_jz4780_efuse.
>> +
>> config NVMEM_LPC18XX_EEPROM
>> tristate "NXP LPC18XX EEPROM Memory Support"
>> depends on ARCH_LPC18XX || COMPILE_TEST
>> diff --git a/drivers/nvmem/Makefile b/drivers/nvmem/Makefile
>> index 6b466cd1427b..65a268d17807 100644
>> --- a/drivers/nvmem/Makefile
>> +++ b/drivers/nvmem/Makefile
>> @@ -18,6 +18,8 @@ obj-$(CONFIG_NVMEM_IMX_OCOTP) += nvmem-imx-ocotp.o
>> nvmem-imx-ocotp-y := imx-ocotp.o
>> obj-$(CONFIG_NVMEM_IMX_OCOTP_SCU) += nvmem-imx-ocotp-scu.o
>> nvmem-imx-ocotp-scu-y := imx-ocotp-scu.o
>> +obj-$(CONFIG_JZ4780_EFUSE) += nvmem_jz4780_efuse.o
>> +nvmem_jz4780_efuse-y := jz4780-efuse.o
>> obj-$(CONFIG_NVMEM_LPC18XX_EEPROM) += nvmem_lpc18xx_eeprom.o
>> nvmem_lpc18xx_eeprom-y := lpc18xx_eeprom.o
>> obj-$(CONFIG_NVMEM_LPC18XX_OTP) += nvmem_lpc18xx_otp.o
>> diff --git a/drivers/nvmem/jz4780-efuse.c b/drivers/nvmem/jz4780-efuse.c
>> new file mode 100644
>> index 000000000000..08b63de0e9cc
>> --- /dev/null
>> +++ b/drivers/nvmem/jz4780-efuse.c
>> @@ -0,0 +1,229 @@
>> +// SPDX-License-Identifier: GPL-2.0-or-later
>> +/*
>> + * JZ4780 EFUSE Memory Support driver
>> + *
>> + * Copyright (c) 2017 PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>> + * Copyright (c) 2020 H. Nikolaus Schaller <hns@goldelico.com>
>> + */
>> +
>> +/*
>> + * Currently supports JZ4780 efuse which has 8K programmable bit.
>> + * Efuse is separated into seven segments as below:
>> + *
>> + * -----------------------------------------------------------------------
>> + * | 64 bit | 128 bit | 128 bit | 3520 bit | 8 bit | 2296 bit | 2048 bit |
>> + * -----------------------------------------------------------------------
>> + *
>> + * The rom itself is accessed using a 9 bit address line and an 8 word wide bus
>> + * which reads/writes based on strobes. The strobe is configured in the config
>> + * register and is based on number of cycles of the bus clock.
>> + *
>> + * Driver supports read only as the writes are done in the Factory.
>> + */
>> +
>> +#include <linux/bitops.h>
>> +#include <linux/clk.h>
>> +#include <linux/module.h>
>> +#include <linux/nvmem-provider.h>
>> +#include <linux/of.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +#include <linux/timer.h>
>> +
>> +#define JZ_EFUCTRL (0x0) /* Control Register */
>> +#define JZ_EFUCFG (0x4) /* Configure Register*/
>> +#define JZ_EFUSTATE (0x8) /* Status Register */
>> +#define JZ_EFUDATA(n) (0xC + (n) * 4)
>> +
>> +#define EFUCTRL_ADDR_MASK 0x3FF
>> +#define EFUCTRL_ADDR_SHIFT 21
>> +#define EFUCTRL_LEN_MASK 0x1F
>> +#define EFUCTRL_LEN_SHIFT 16
>> +#define EFUCTRL_PG_EN BIT(15)
>> +#define EFUCTRL_WR_EN BIT(1)
>> +#define EFUCTRL_RD_EN BIT(0)
>> +
>> +#define EFUCFG_INT_EN BIT(31)
>> +#define EFUCFG_RD_ADJ_MASK 0xF
>> +#define EFUCFG_RD_ADJ_SHIFT 20
>> +#define EFUCFG_RD_STR_MASK 0xF
>> +#define EFUCFG_RD_STR_SHIFT 16
>> +#define EFUCFG_WR_ADJ_MASK 0xF
>> +#define EFUCFG_WR_ADJ_SHIFT 12
>> +#define EFUCFG_WR_STR_MASK 0xFFF
>> +#define EFUCFG_WR_STR_SHIFT 0
>> +
>> +#define EFUSTATE_WR_DONE BIT(1)
>> +#define EFUSTATE_RD_DONE BIT(0)
>> +
>> +struct jz4780_efuse {
>> + struct device *dev;
>> + struct regmap *map;
>> + struct clk *clk;
>> + unsigned int rd_adj;
>> + unsigned int rd_strobe;
>> +};
>> +
>> +/* We read 32 byte chunks to avoid complexity in the driver. */
>
> I don't see how reading 32 byte chunks avoids complexity in the driver; the 'size' variable here could very well be an argument.
I mixed your, mine and the original code.
One issue with a size argument is that regmap reads in 32bit words.
But reading the ethernet MAC address requires to fetch 6 bytes.
AFAIK regmap can only read in multiples of the word size.
It must also be possible to read starting at any byte address.
>
>> +static int jz4780_efuse_read_32bytes(struct jz4780_efuse *efuse, char *buf,
>> + unsigned int addr)
>> +{
>> + unsigned int tmp;
>> + u32 ctrl;
>> + int ret;
>> + const int size = 32;
>> +
>> + ctrl = (addr << EFUCTRL_ADDR_SHIFT)
>> + | ((size - 1) << EFUCTRL_LEN_SHIFT)
>> + | EFUCTRL_RD_EN;
>> +
>> + regmap_update_bits(efuse->map, JZ_EFUCTRL,
>> + (EFUCTRL_ADDR_MASK << EFUCTRL_ADDR_SHIFT) |
>> + (EFUCTRL_LEN_MASK << EFUCTRL_LEN_SHIFT) |
>> + EFUCTRL_PG_EN | EFUCTRL_WR_EN | EFUCTRL_RD_EN, ctrl);
>> +
>> + ret = regmap_read_poll_timeout(efuse->map, JZ_EFUSTATE,
>> + tmp, tmp & EFUSTATE_RD_DONE,
>> + 1 * MSEC_PER_SEC, 50 * MSEC_PER_SEC);
>> + if (ret < 0) {
>> + dev_err(efuse->dev, "Time out while reading efuse data");
>> + return ret;
>> + }
>> +
>> + return regmap_bulk_read(efuse->map, JZ_EFUDATA(0),
>> + buf, size / sizeof(u32));
>> +}
>> +
>> +/* main entry point */
>> +static int jz4780_efuse_read(void *context, unsigned int offset,
>> + void *val, size_t bytes)
>> +{
>> + struct jz4780_efuse *efuse = context;
>> + int ret;
>> + const int size = 32;
>> +
>> + while (bytes > 0) {
>> + unsigned int start = offset & ~(size - 1);
>> + unsigned int chunk = min(bytes, (start + size) - offset);
>
> Why do you need to check for the address alignment?
This is to decide if jz4780_efuse_read_32bytes() can directly read to the
destination buffer or if we need a temporary buffer. This avoids to always
use a temporary buffer.
>
>> +
>> + if (start == offset && chunk == size) {
>> + ret = jz4780_efuse_read_32bytes(efuse, val, start);
>> + if (ret < 0)
>> + return ret;
>> +
>> + } else {
>> + char buf[32];
>> +
>> + ret = jz4780_efuse_read_32bytes(efuse, buf, start);
>> + if (ret < 0)
>> + return ret;
>> +
>> + memcpy(val, &buf[offset - start], chunk);
>
> Why do you need this cumbersome process of reading 32 bytes if you need less than that? This looks over-complex to me.
MAC address must allow to read 6 Bytes. I am not sure if regmap can do that.
According to the Programming Manual there are 8 registers with 32 bits each
so it is probably wise to read all these 32 bytes in one big read into the
regmap. So that it is never attempted to read smaller or not 32bit aligned
registers. This also makes sure that bank address switching is not done for
every byte.
>
>> + }
>> +
>> + val += chunk;
>> + offset += chunk;
>> + bytes -= chunk;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static struct nvmem_config jz4780_efuse_nvmem_config __initdata = {
>> + .name = "jz4780-efuse",
>> + .size = 1024,
>
> The efuse is 8 KiB.
I read the Programming Manual as 8 kBit = 1024 Byte. See for example
Note 1. and 2. in section "26.2.4 EFUSE Data Register (EFUDATAn)"
>
>> + .word_size = 1,
>> + .stride = 1,
>> + .owner = THIS_MODULE,
>> + .reg_read = jz4780_efuse_read,
>> +};
>> +
>> +static const struct regmap_config jz4780_efuse_regmap_config = {
>> + .reg_bits = 32,
>> + .val_bits = 32,
>> + .reg_stride = 4,
>> + .max_register = JZ_EFUDATA(7),
>> +};
>> +
>> +static int jz4780_efuse_probe(struct platform_device *pdev)
>> +{
>> + struct nvmem_device *nvmem;
>> + struct jz4780_efuse *efuse;
>> + struct nvmem_config cfg;
>> + unsigned long clk_rate;
>> + struct device *dev = &pdev->dev;
>> + void __iomem *regs;
>> +
>> + efuse = devm_kzalloc(dev, sizeof(*efuse), GFP_KERNEL);
>> + if (!efuse)
>> + return -ENOMEM;
>> +
>> + regs = devm_platform_ioremap_resource(pdev, 0);
>> + if (IS_ERR(regs))
>> + return PTR_ERR(regs);
>> +
>> + efuse->map = devm_regmap_init_mmio(dev, regs,
>> + &jz4780_efuse_regmap_config);
>> + if (IS_ERR(efuse->map))
>> + return PTR_ERR(efuse->map);
>> +
>> + efuse->clk = devm_clk_get(&pdev->dev, NULL);
>> + if (IS_ERR(efuse->clk))
>> + return PTR_ERR(efuse->clk);
>> +
>> + clk_rate = clk_get_rate(efuse->clk);
>
> You didn't enable the clock before, so clk_get_rate can return a bogus value.
Well, I copied that from your proposal for jz4780_efuse_probe().
So I don't know if that is correct or not...
How should it be solved? clk_enable() before and clk_disable() after?
Or is it enabled somewhere else so that we break something if
we explicitly disable?
>
>> +
>> + efuse->dev = dev;
>> + /*
>> + * rd_adj and rd_strobe are 4 bit values
>> + * bus clk period * (rd_adj + 1) > 6.5ns
>> + * bus clk period * (rd_adj + 5 + rd_strobe) > 35ns
>> + */
>> + efuse->rd_adj = (((6500 * (clk_rate / 1000000)) / 1000000) + 1) - 1;
>
> I can't get my head around this calculus. Try this:
I would read it as: multiply clk_rate (in MHz units) by 6.5 and divide by another 1000.
So if clock rate is e.g. 500 Mhz we calculate 6.5 * 500 / 1000 => 3(.25).
500 Mhz is equivalent to 2 ns so 2 ns * 3.25 = 6.5 ns.
But that said: there seems to be something wrong with rounding. To fulfill the
> 6.5 ns condition the 3.25 should be rounded up to 4.
But since the condition is defined for rd_adj + 1 it is ok to set rd_adj to 3 in this case.
>
> /* 1 / 6.5ns == 153846154 Hz */
> efuse->rd_adj = clk_rate / 153846154;
>
> The efuse read should be *at least* 6.5ns, so no need to bother with the -1/+1.
Well, the (X + 1) - 1 looks very redundant.
So what about:
#define RD_ADJ_FACTOR (unsigned long)(10 * NSEC_PER_SEC / 65) /* 1 / 6.5ns == 153846154 Hz */
efuse->rd_adj = clk_rate / RD_ADJ_FACTOR;
>
>> + efuse->rd_strobe = ((((35000 * (clk_rate / 1000000)) / 1000000) + 1)
>> + - 5 - efuse->rd_adj);
>
> /* 1 / 35ns == 28571429 Hz */
> efuse->rd_strobe = max(0, clk_rate / 28571429 + 1 - 5 - efuse->rd_adj);
I think the original author just wanted to make the magic values a little
more transparent. 35000 / 1000000 is easier to recognise as 35 ns in the
programming manual than 28571429.
>
>> +
>> + if (efuse->rd_adj > 0x1F || efuse->rd_strobe > 0x1F) {
>> + dev_err(&pdev->dev, "Cannot set clock configuration\n");
>> + return -EINVAL;
>> + }
>> +
>> + regmap_update_bits(efuse->map, JZ_EFUCFG,
>> + (EFUCFG_RD_ADJ_MASK << EFUCFG_RD_ADJ_SHIFT) |
>> + (EFUCFG_RD_STR_MASK << EFUCFG_RD_STR_SHIFT),
>> + (efuse->rd_adj << EFUCFG_RD_ADJ_SHIFT) |
>> + (efuse->rd_strobe << EFUCFG_RD_STR_SHIFT));
>> +
>> + cfg = jz4780_efuse_nvmem_config;
>> + cfg.dev = &pdev->dev;
>> + cfg.priv = efuse;
>> +
>> + nvmem = devm_nvmem_register(dev, &cfg);
>> + if (IS_ERR(nvmem))
>> + return PTR_ERR(nvmem);
>> +
>> + platform_set_drvdata(pdev, nvmem);
>
> This isn't used anywhere.
Also copied from your proposal...
But it is indeed not used anywhere.
A big question is why we need to store rd_adj and rd_strobe in the
struct jz4780_efuse? They are local variables inside jz4780_efuse_probe().
So the only values used are efuse->map
>
>> +
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id jz4780_efuse_match[] = {
>> + { .compatible = "ingenic,jz4780-efuse" },
>> + { /* sentinel */ },
>> +};
>> +MODULE_DEVICE_TABLE(of, jz4780_efuse_match);
>> +
>> +static struct platform_driver jz4780_efuse_driver = {
>> + .probe = jz4780_efuse_probe,
>> + .driver = {
>> + .name = "jz4780-efuse",
>> + .of_match_table = jz4780_efuse_match,
>> + },
>> +};
>> +module_platform_driver(jz4780_efuse_driver);
>> +
>> +MODULE_AUTHOR("PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>");
>> +MODULE_AUTHOR("H. Nikolaus Schaller <hns@goldelico.com>");
>> +MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
>> +MODULE_DESCRIPTION("Ingenic JZ4780 efuse driver");
>> +MODULE_LICENSE("GPL v2");
>> --
>> 2.23.0
BR and thanks,
Nikolaus
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH v5 1/6] nvmem: add driver for JZ4780 efuse
2020-02-22 17:16 ` H. Nikolaus Schaller
@ 2020-02-22 18:13 ` Paul Cercueil
0 siblings, 0 replies; 17+ messages in thread
From: Paul Cercueil @ 2020-02-22 18:13 UTC (permalink / raw)
To: H. Nikolaus Schaller
Cc: PrasannaKumar Muralidharan, Andreas Kemnade, Mathieu Malaterre,
Srinivas Kandagatla, Rob Herring, Mark Rutland, Ralf Baechle,
Paul Burton, Mauro Carvalho Chehab, David S. Miller,
Greg Kroah-Hartman, Jonathan Cameron, Krzysztof Kozlowski,
Kees Cook, Andi Kleen, Geert Uytterhoeven, linux-kernel,
devicetree, linux-mips, letux-kernel, kernel
Hi Nikolaus,
Le sam., févr. 22, 2020 at 18:16, H. Nikolaus Schaller
<hns@goldelico.com> a écrit :
> Hi Paul,
>
>> Am 22.02.2020 um 16:38 schrieb Paul Cercueil <paul@crapouillou.net>:
>>
>> Hi Nikolaus,
>>
>>
>> Le sam., févr. 22, 2020 at 11:25, H. Nikolaus Schaller
>> <hns@goldelico.com> a écrit :
>>> From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>>> This patch brings support for the JZ4780 efuse. Currently it only
>>> exposes
>>> a read only access to the entire 8K bits efuse memory and nvmem
>>> cells.
>>> Tested-by: Mathieu Malaterre <malat@debian.org>
>>> Signed-off-by: PrasannaKumar Muralidharan
>>> <prasannatsmkumar@gmail.com>
>>> Signed-off-by: Mathieu Malaterre <malat@debian.org>
>>> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
>>> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
>>> ---
>>> drivers/nvmem/Kconfig | 10 ++
>>> drivers/nvmem/Makefile | 2 +
>>> drivers/nvmem/jz4780-efuse.c | 229
>>> +++++++++++++++++++++++++++++++++++
>>> 3 files changed, 241 insertions(+)
>>> create mode 100644 drivers/nvmem/jz4780-efuse.c
>>> diff --git a/drivers/nvmem/Kconfig b/drivers/nvmem/Kconfig
>>> index 35efab1ba8d9..8143e6e1dd82 100644
>>> --- a/drivers/nvmem/Kconfig
>>> +++ b/drivers/nvmem/Kconfig
>>> @@ -55,6 +55,16 @@ config NVMEM_IMX_OCOTP_SCU
>>> This is a driver for the SCU On-Chip OTP Controller (OCOTP)
>>> available on i.MX8 SoCs.
>>> +config JZ4780_EFUSE
>>> + tristate "JZ4780 EFUSE Memory Support"
>>> + depends on MACH_INGENIC || COMPILE_TEST
>>> + depends on HAS_IOMEM
>>
>> You're using regmap, so you need to select REGMAP_MMIO here.
>
> Ok.
I think you need to depend on OF too, since the driver only probes on
devicetree.
>>
>>> + help
>>> + Say Y here to include support for JZ4780 efuse memory found on
>>> + all JZ4780 SoC based devices.
>>> + To compile this driver as a module, choose M here: the module
>>> + will be called nvmem_jz4780_efuse.
>>> +
>>> config NVMEM_LPC18XX_EEPROM
>>> tristate "NXP LPC18XX EEPROM Memory Support"
>>> depends on ARCH_LPC18XX || COMPILE_TEST
>>> diff --git a/drivers/nvmem/Makefile b/drivers/nvmem/Makefile
>>> index 6b466cd1427b..65a268d17807 100644
>>> --- a/drivers/nvmem/Makefile
>>> +++ b/drivers/nvmem/Makefile
>>> @@ -18,6 +18,8 @@ obj-$(CONFIG_NVMEM_IMX_OCOTP) +=
>>> nvmem-imx-ocotp.o
>>> nvmem-imx-ocotp-y := imx-ocotp.o
>>> obj-$(CONFIG_NVMEM_IMX_OCOTP_SCU) += nvmem-imx-ocotp-scu.o
>>> nvmem-imx-ocotp-scu-y := imx-ocotp-scu.o
>>> +obj-$(CONFIG_JZ4780_EFUSE) += nvmem_jz4780_efuse.o
>>> +nvmem_jz4780_efuse-y := jz4780-efuse.o
>>> obj-$(CONFIG_NVMEM_LPC18XX_EEPROM) += nvmem_lpc18xx_eeprom.o
>>> nvmem_lpc18xx_eeprom-y := lpc18xx_eeprom.o
>>> obj-$(CONFIG_NVMEM_LPC18XX_OTP) += nvmem_lpc18xx_otp.o
>>> diff --git a/drivers/nvmem/jz4780-efuse.c
>>> b/drivers/nvmem/jz4780-efuse.c
>>> new file mode 100644
>>> index 000000000000..08b63de0e9cc
>>> --- /dev/null
>>> +++ b/drivers/nvmem/jz4780-efuse.c
>>> @@ -0,0 +1,229 @@
>>> +// SPDX-License-Identifier: GPL-2.0-or-later
>>> +/*
>>> + * JZ4780 EFUSE Memory Support driver
>>> + *
>>> + * Copyright (c) 2017 PrasannaKumar Muralidharan
>>> <prasannatsmkumar@gmail.com>
>>> + * Copyright (c) 2020 H. Nikolaus Schaller <hns@goldelico.com>
>>> + */
>>> +
>>> +/*
>>> + * Currently supports JZ4780 efuse which has 8K programmable bit.
>>> + * Efuse is separated into seven segments as below:
>>> + *
>>> + *
>>> -----------------------------------------------------------------------
>>> + * | 64 bit | 128 bit | 128 bit | 3520 bit | 8 bit | 2296 bit |
>>> 2048 bit |
>>> + *
>>> -----------------------------------------------------------------------
>>> + *
>>> + * The rom itself is accessed using a 9 bit address line and an 8
>>> word wide bus
>>> + * which reads/writes based on strobes. The strobe is configured
>>> in the config
>>> + * register and is based on number of cycles of the bus clock.
>>> + *
>>> + * Driver supports read only as the writes are done in the
>>> Factory.
>>> + */
>>> +
>>> +#include <linux/bitops.h>
>>> +#include <linux/clk.h>
>>> +#include <linux/module.h>
>>> +#include <linux/nvmem-provider.h>
>>> +#include <linux/of.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/regmap.h>
>>> +#include <linux/timer.h>
>>> +
>>> +#define JZ_EFUCTRL (0x0) /* Control Register */
>>> +#define JZ_EFUCFG (0x4) /* Configure Register*/
>>> +#define JZ_EFUSTATE (0x8) /* Status Register */
>>> +#define JZ_EFUDATA(n) (0xC + (n) * 4)
>>> +
>>> +#define EFUCTRL_ADDR_MASK 0x3FF
>>> +#define EFUCTRL_ADDR_SHIFT 21
>>> +#define EFUCTRL_LEN_MASK 0x1F
>>> +#define EFUCTRL_LEN_SHIFT 16
>>> +#define EFUCTRL_PG_EN BIT(15)
>>> +#define EFUCTRL_WR_EN BIT(1)
>>> +#define EFUCTRL_RD_EN BIT(0)
>>> +
>>> +#define EFUCFG_INT_EN BIT(31)
>>> +#define EFUCFG_RD_ADJ_MASK 0xF
>>> +#define EFUCFG_RD_ADJ_SHIFT 20
>>> +#define EFUCFG_RD_STR_MASK 0xF
>>> +#define EFUCFG_RD_STR_SHIFT 16
>>> +#define EFUCFG_WR_ADJ_MASK 0xF
>>> +#define EFUCFG_WR_ADJ_SHIFT 12
>>> +#define EFUCFG_WR_STR_MASK 0xFFF
>>> +#define EFUCFG_WR_STR_SHIFT 0
>>> +
>>> +#define EFUSTATE_WR_DONE BIT(1)
>>> +#define EFUSTATE_RD_DONE BIT(0)
>>> +
>>> +struct jz4780_efuse {
>>> + struct device *dev;
>>> + struct regmap *map;
>>> + struct clk *clk;
>>> + unsigned int rd_adj;
>>> + unsigned int rd_strobe;
>>> +};
>>> +
>>> +/* We read 32 byte chunks to avoid complexity in the driver. */
>>
>> I don't see how reading 32 byte chunks avoids complexity in the
>> driver; the 'size' variable here could very well be an argument.
>
> I mixed your, mine and the original code.
>
> One issue with a size argument is that regmap reads in 32bit words.
>
> But reading the ethernet MAC address requires to fetch 6 bytes.
> AFAIK regmap can only read in multiples of the word size.
>
> It must also be possible to read starting at any byte address.
Right, I didn't think about byte access.
>>
>>> +static int jz4780_efuse_read_32bytes(struct jz4780_efuse *efuse,
>>> char *buf,
>>> + unsigned int addr)
>>> +{
>>> + unsigned int tmp;
>>> + u32 ctrl;
>>> + int ret;
>>> + const int size = 32;
>>> +
>>> + ctrl = (addr << EFUCTRL_ADDR_SHIFT)
>>> + | ((size - 1) << EFUCTRL_LEN_SHIFT)
>>> + | EFUCTRL_RD_EN;
>>> +
>>> + regmap_update_bits(efuse->map, JZ_EFUCTRL,
>>> + (EFUCTRL_ADDR_MASK << EFUCTRL_ADDR_SHIFT) |
>>> + (EFUCTRL_LEN_MASK << EFUCTRL_LEN_SHIFT) |
>>> + EFUCTRL_PG_EN | EFUCTRL_WR_EN | EFUCTRL_RD_EN, ctrl);
>>> +
>>> + ret = regmap_read_poll_timeout(efuse->map, JZ_EFUSTATE,
>>> + tmp, tmp & EFUSTATE_RD_DONE,
>>> + 1 * MSEC_PER_SEC, 50 * MSEC_PER_SEC);
>>> + if (ret < 0) {
>>> + dev_err(efuse->dev, "Time out while reading efuse data");
>>> + return ret;
>>> + }
>>> +
>>> + return regmap_bulk_read(efuse->map, JZ_EFUDATA(0),
>>> + buf, size / sizeof(u32));
>>> +}
>>> +
>>> +/* main entry point */
>>> +static int jz4780_efuse_read(void *context, unsigned int offset,
>>> + void *val, size_t bytes)
>>> +{
>>> + struct jz4780_efuse *efuse = context;
>>> + int ret;
>>> + const int size = 32;
>>> +
>>> + while (bytes > 0) {
>>> + unsigned int start = offset & ~(size - 1);
>>> + unsigned int chunk = min(bytes, (start + size) - offset);
>>
>> Why do you need to check for the address alignment?
>
> This is to decide if jz4780_efuse_read_32bytes() can directly read to
> the
> destination buffer or if we need a temporary buffer. This avoids to
> always
> use a temporary buffer.
Just always use a temporary buffer. It's not like this will be called
very often anyway. That makes the code simpler.
>>
>>> +
>>> + if (start == offset && chunk == size) {
>>> + ret = jz4780_efuse_read_32bytes(efuse, val, start);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + } else {
>>> + char buf[32];
>>> +
>>> + ret = jz4780_efuse_read_32bytes(efuse, buf, start);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + memcpy(val, &buf[offset - start], chunk);
>>
>> Why do you need this cumbersome process of reading 32 bytes if you
>> need less than that? This looks over-complex to me.
>
> MAC address must allow to read 6 Bytes. I am not sure if regmap can
> do that.
>
> According to the Programming Manual there are 8 registers with 32
> bits each
> so it is probably wise to read all these 32 bytes in one big read
> into the
> regmap. So that it is never attempted to read smaller or not 32bit
> aligned
> registers. This also makes sure that bank address switching is not
> done for
> every byte.
Honestly, it doesn't have to be fast. You could very well read byte per
byte. Then you wouldn't have to care about non-aligned addresses or
sizes, and the driver would be much simpler.
>>
>>> + }
>>> +
>>> + val += chunk;
>>> + offset += chunk;
>>> + bytes -= chunk;
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static struct nvmem_config jz4780_efuse_nvmem_config __initdata =
>>> {
>>> + .name = "jz4780-efuse",
>>> + .size = 1024,
>>
>> The efuse is 8 KiB.
>
> I read the Programming Manual as 8 kBit = 1024 Byte. See for example
> Note 1. and 2. in section "26.2.4 EFUSE Data Register (EFUDATAn)"
Right. 8 Kib, not KiB.
>>
>>> + .word_size = 1,
>>> + .stride = 1,
>>> + .owner = THIS_MODULE,
>>> + .reg_read = jz4780_efuse_read,
>>> +};
>>> +
>>> +static const struct regmap_config jz4780_efuse_regmap_config = {
>>> + .reg_bits = 32,
>>> + .val_bits = 32,
>>> + .reg_stride = 4,
>>> + .max_register = JZ_EFUDATA(7),
>>> +};
>>> +
>>> +static int jz4780_efuse_probe(struct platform_device *pdev)
>>> +{
>>> + struct nvmem_device *nvmem;
>>> + struct jz4780_efuse *efuse;
>>> + struct nvmem_config cfg;
>>> + unsigned long clk_rate;
>>> + struct device *dev = &pdev->dev;
>>> + void __iomem *regs;
>>> +
>>> + efuse = devm_kzalloc(dev, sizeof(*efuse), GFP_KERNEL);
>>> + if (!efuse)
>>> + return -ENOMEM;
>>> +
>>> + regs = devm_platform_ioremap_resource(pdev, 0);
>>> + if (IS_ERR(regs))
>>> + return PTR_ERR(regs);
>>> +
>>> + efuse->map = devm_regmap_init_mmio(dev, regs,
>>> + &jz4780_efuse_regmap_config);
>>> + if (IS_ERR(efuse->map))
>>> + return PTR_ERR(efuse->map);
>>> +
>>> + efuse->clk = devm_clk_get(&pdev->dev, NULL);
>>> + if (IS_ERR(efuse->clk))
>>> + return PTR_ERR(efuse->clk);
>>> +
>>> + clk_rate = clk_get_rate(efuse->clk);
>>
>> You didn't enable the clock before, so clk_get_rate can return a
>> bogus value.
>
> Well, I copied that from your proposal for jz4780_efuse_probe().
> So I don't know if that is correct or not...
> How should it be solved? clk_enable() before and clk_disable() after?
> Or is it enabled somewhere else so that we break something if
> we explicitly disable?
clk_prepare_enable() here, and clk_disable_unprepare() in the remove
callback or in a function passed to devm_add_action_or_reset().
>>
>>> +
>>> + efuse->dev = dev;
>>> + /*
>>> + * rd_adj and rd_strobe are 4 bit values
>>> + * bus clk period * (rd_adj + 1) > 6.5ns
>>> + * bus clk period * (rd_adj + 5 + rd_strobe) > 35ns
>>> + */
>>> + efuse->rd_adj = (((6500 * (clk_rate / 1000000)) / 1000000) + 1)
>>> - 1;
>>
>> I can't get my head around this calculus. Try this:
>
> I would read it as: multiply clk_rate (in MHz units) by 6.5 and
> divide by another 1000.
>
> So if clock rate is e.g. 500 Mhz we calculate 6.5 * 500 / 1000 =>
> 3(.25).
> 500 Mhz is equivalent to 2 ns so 2 ns * 3.25 = 6.5 ns.
Yes, I'm not saying that the calculus is wrong. But it multiplies
picoseconds with MHz, then divides by 1000000, so it's not easy to
understand.
> But that said: there seems to be something wrong with rounding. To
> fulfill the
>> 6.5 ns condition the 3.25 should be rounded up to 4.
>
> But since the condition is defined for rd_adj + 1 it is ok to set
> rd_adj to 3 in this case.
>
>>
>> /* 1 / 6.5ns == 153846154 Hz */
>> efuse->rd_adj = clk_rate / 153846154;
>>
>> The efuse read should be *at least* 6.5ns, so no need to bother
>> with the -1/+1.
>
> Well, the (X + 1) - 1 looks very redundant.
>
> So what about:
>
> #define RD_ADJ_FACTOR (unsigned long)(10 * NSEC_PER_SEC / 65) /* 1 /
> 6.5ns == 153846154 Hz */
>
> efuse->rd_adj = clk_rate / RD_ADJ_FACTOR;
Well, you still need the comment after the #define, so why use a
#define in the first place?
>>
>>> + efuse->rd_strobe = ((((35000 * (clk_rate / 1000000)) / 1000000)
>>> + 1)
>>> + - 5 - efuse->rd_adj);
>>
>> /* 1 / 35ns == 28571429 Hz */
>> efuse->rd_strobe = max(0, clk_rate / 28571429 + 1 - 5 -
>> efuse->rd_adj);
>
> I think the original author just wanted to make the magic values a
> little
> more transparent. 35000 / 1000000 is easier to recognise as 35 ns in
> the
> programming manual than 28571429.
35000 / 1000000 is 35ms, not 35ns.
28571429 Hz is easy to recognize as 35ns when there's a comment right
above saying where that value comes from.
>
>>
>>> +
>>> + if (efuse->rd_adj > 0x1F || efuse->rd_strobe > 0x1F) {
>>> + dev_err(&pdev->dev, "Cannot set clock configuration\n");
>>> + return -EINVAL;
>>> + }
>>> +
>>> + regmap_update_bits(efuse->map, JZ_EFUCFG,
>>> + (EFUCFG_RD_ADJ_MASK << EFUCFG_RD_ADJ_SHIFT) |
>>> + (EFUCFG_RD_STR_MASK << EFUCFG_RD_STR_SHIFT),
>>> + (efuse->rd_adj << EFUCFG_RD_ADJ_SHIFT) |
>>> + (efuse->rd_strobe << EFUCFG_RD_STR_SHIFT));
>>> +
>>> + cfg = jz4780_efuse_nvmem_config;
>>> + cfg.dev = &pdev->dev;
>>> + cfg.priv = efuse;
>>> +
>>> + nvmem = devm_nvmem_register(dev, &cfg);
>>> + if (IS_ERR(nvmem))
>>> + return PTR_ERR(nvmem);
>>> +
>>> + platform_set_drvdata(pdev, nvmem);
>>
>> This isn't used anywhere.
>
> Also copied from your proposal...
> But it is indeed not used anywhere.
My code wasn't upstream-ready, and wasn't even tested on real hardware.
I'm reviewing the driver for mainline inclusion now.
> A big question is why we need to store rd_adj and rd_strobe in the
> struct jz4780_efuse? They are local variables inside
> jz4780_efuse_probe().
Maybe move the calculation of rd_adj / rd_strobe to a new function
that's called from the probe, and have these local variables within
this function.
> So the only values used are efuse->map
>
>>
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static const struct of_device_id jz4780_efuse_match[] = {
>>> + { .compatible = "ingenic,jz4780-efuse" },
>>> + { /* sentinel */ },
>>> +};
>>> +MODULE_DEVICE_TABLE(of, jz4780_efuse_match);
>>> +
>>> +static struct platform_driver jz4780_efuse_driver = {
>>> + .probe = jz4780_efuse_probe,
>>> + .driver = {
>>> + .name = "jz4780-efuse",
>>> + .of_match_table = jz4780_efuse_match,
>>> + },
>>> +};
>>> +module_platform_driver(jz4780_efuse_driver);
>>> +
>>> +MODULE_AUTHOR("PrasannaKumar Muralidharan
>>> <prasannatsmkumar@gmail.com>");
>>> +MODULE_AUTHOR("H. Nikolaus Schaller <hns@goldelico.com>");
>>> +MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
>>> +MODULE_DESCRIPTION("Ingenic JZ4780 efuse driver");
>>> +MODULE_LICENSE("GPL v2");
>>> --
>>> 2.23.0
>
>
> BR and thanks,
> Nikolaus
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH v5 2/6] Bindings: nvmem: add bindings for JZ4780 efuse
2020-02-22 10:25 [PATCH v5 0/6] MIPS: CI20: Add efuse driver for Ingenic JZ4780 and attach to DM9000 for stable MAC addresses H. Nikolaus Schaller
2020-02-22 10:25 ` [PATCH v5 1/6] nvmem: add driver for JZ4780 efuse H. Nikolaus Schaller
@ 2020-02-22 10:25 ` H. Nikolaus Schaller
2020-02-22 10:54 ` Andreas Kemnade
2020-02-22 15:57 ` Andreas Kemnade
2020-02-22 10:25 ` [PATCH v5 3/6] Documentation: ABI: nvmem: add documentation for JZ4780 efuse ABI H. Nikolaus Schaller
` (3 subsequent siblings)
5 siblings, 2 replies; 17+ messages in thread
From: H. Nikolaus Schaller @ 2020-02-22 10:25 UTC (permalink / raw)
To: PrasannaKumar Muralidharan, Andreas Kemnade, Paul Cercueil,
Mathieu Malaterre, Srinivas Kandagatla, Rob Herring,
Mark Rutland, Ralf Baechle, Paul Burton, Mauro Carvalho Chehab,
David S. Miller, Greg Kroah-Hartman, Jonathan Cameron,
H. Nikolaus Schaller, Krzysztof Kozlowski, Kees Cook, Andi Kleen,
Geert Uytterhoeven
Cc: linux-kernel, devicetree, linux-mips, letux-kernel, kernel
From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
[converted to yaml]
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
---
.../bindings/nvmem/ingenic,jz4780-efuse.yaml | 50 +++++++++++++++++++
1 file changed, 50 insertions(+)
create mode 100644 Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
diff --git a/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
new file mode 100644
index 000000000000..09a8ef937750
--- /dev/null
+++ b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/nvmem/ingenic,jz4780-efuse.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic JZ EFUSE driver bindings
+
+maintainers:
+ - PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
+
+allOf:
+ - $ref: "nvmem.yaml#"
+
+properties:
+ compatible:
+ enum:
+ - ingenic,jz4780-efuse
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ # Handle for the ahb for the efuse.
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: ahb2
+
+required:
+ - compatible
+ - reg
+ - clock-names
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/jz4780-cgu.h>
+
+ efuse@134100d0 {
+ compatible = "ingenic,jz4780-efuse";
+ reg = <0x134100d0 0x2c>;
+
+ clocks = <&cgu JZ4780_CLK_AHB2>;
+ clock-names = "ahb2";
+ };
+
+...
--
2.23.0
^ permalink raw reply related [flat|nested] 17+ messages in thread* Re: [PATCH v5 2/6] Bindings: nvmem: add bindings for JZ4780 efuse
2020-02-22 10:25 ` [PATCH v5 2/6] Bindings: nvmem: add bindings " H. Nikolaus Schaller
@ 2020-02-22 10:54 ` Andreas Kemnade
2020-02-22 16:28 ` H. Nikolaus Schaller
2020-02-22 15:57 ` Andreas Kemnade
1 sibling, 1 reply; 17+ messages in thread
From: Andreas Kemnade @ 2020-02-22 10:54 UTC (permalink / raw)
To: H. Nikolaus Schaller
Cc: PrasannaKumar Muralidharan, Paul Cercueil, Mathieu Malaterre,
Srinivas Kandagatla, Rob Herring, Mark Rutland, Ralf Baechle,
Paul Burton, Mauro Carvalho Chehab, David S. Miller,
Greg Kroah-Hartman, Jonathan Cameron, Krzysztof Kozlowski,
Kees Cook, Andi Kleen, Geert Uytterhoeven, linux-kernel,
devicetree, linux-mips, letux-kernel, kernel
[-- Attachment #1: Type: text/plain, Size: 1986 bytes --]
On Sat, 22 Feb 2020 11:25:37 +0100
"H. Nikolaus Schaller" <hns@goldelico.com> wrote:
> From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>
> This patch brings support for the JZ4780 efuse. Currently it only exposes
> a read only access to the entire 8K bits efuse memory.
>
> Tested-by: Mathieu Malaterre <malat@debian.org>
> Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> Signed-off-by: Mathieu Malaterre <malat@debian.org>
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> [converted to yaml]
> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> ---
> .../bindings/nvmem/ingenic,jz4780-efuse.yaml | 50 +++++++++++++++++++
> 1 file changed, 50 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>
> diff --git a/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
> new file mode 100644
> index 000000000000..09a8ef937750
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
> @@ -0,0 +1,50 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/nvmem/ingenic,jz4780-efuse.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Ingenic JZ EFUSE driver bindings
> +
> +maintainers:
> + - PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> +
> +allOf:
> + - $ref: "nvmem.yaml#"
> +
> +properties:
> + compatible:
> + enum:
> + - ingenic,jz4780-efuse
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + # Handle for the ahb for the efuse.
> + maxItems: 1
> +
> + clock-names:
> + items:
> + - const: ahb2
> +
> +required:
> + - compatible
> + - reg
> + - clock-names
- clocks ?
In my first try there was "clock" without s which
caused the trouble.
Regards,
Andreas
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v5 2/6] Bindings: nvmem: add bindings for JZ4780 efuse
2020-02-22 10:54 ` Andreas Kemnade
@ 2020-02-22 16:28 ` H. Nikolaus Schaller
0 siblings, 0 replies; 17+ messages in thread
From: H. Nikolaus Schaller @ 2020-02-22 16:28 UTC (permalink / raw)
To: Andreas Kemnade
Cc: PrasannaKumar Muralidharan, Paul Cercueil, Mathieu Malaterre,
Srinivas Kandagatla, Rob Herring, Mark Rutland, Ralf Baechle,
Paul Burton, Mauro Carvalho Chehab, David S. Miller,
Greg Kroah-Hartman, Jonathan Cameron, Krzysztof Kozlowski,
Kees Cook, Andi Kleen, Geert Uytterhoeven, linux-kernel,
devicetree, linux-mips, letux-kernel, kernel
> Am 22.02.2020 um 11:54 schrieb Andreas Kemnade <andreas@kemnade.info>:
>
> On Sat, 22 Feb 2020 11:25:37 +0100
> "H. Nikolaus Schaller" <hns@goldelico.com> wrote:
>
>> From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>>
>> This patch brings support for the JZ4780 efuse. Currently it only exposes
>> a read only access to the entire 8K bits efuse memory.
>>
>> Tested-by: Mathieu Malaterre <malat@debian.org>
>> Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>> Signed-off-by: Mathieu Malaterre <malat@debian.org>
>> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
>> [converted to yaml]
>> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
>> ---
>> .../bindings/nvmem/ingenic,jz4780-efuse.yaml | 50 +++++++++++++++++++
>> 1 file changed, 50 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>> new file mode 100644
>> index 000000000000..09a8ef937750
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>> @@ -0,0 +1,50 @@
>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/nvmem/ingenic,jz4780-efuse.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Ingenic JZ EFUSE driver bindings
>> +
>> +maintainers:
>> + - PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>> +
>> +allOf:
>> + - $ref: "nvmem.yaml#"
>> +
>> +properties:
>> + compatible:
>> + enum:
>> + - ingenic,jz4780-efuse
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + clocks:
>> + # Handle for the ahb for the efuse.
>> + maxItems: 1
>> +
>> + clock-names:
>> + items:
>> + - const: ahb2
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - clock-names
> - clocks ?
>
> In my first try there was "clock" without s which
> caused the trouble.
Ah, ok. Seems I have mis-interpreted this.
BR and thanks,
Nikolaus
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v5 2/6] Bindings: nvmem: add bindings for JZ4780 efuse
2020-02-22 10:25 ` [PATCH v5 2/6] Bindings: nvmem: add bindings " H. Nikolaus Schaller
2020-02-22 10:54 ` Andreas Kemnade
@ 2020-02-22 15:57 ` Andreas Kemnade
2020-02-22 16:34 ` H. Nikolaus Schaller
1 sibling, 1 reply; 17+ messages in thread
From: Andreas Kemnade @ 2020-02-22 15:57 UTC (permalink / raw)
To: H. Nikolaus Schaller
Cc: PrasannaKumar Muralidharan, Paul Cercueil, Mathieu Malaterre,
Srinivas Kandagatla, Rob Herring, Mark Rutland, Ralf Baechle,
Paul Burton, Mauro Carvalho Chehab, David S. Miller,
Greg Kroah-Hartman, Jonathan Cameron, Krzysztof Kozlowski,
Kees Cook, Andi Kleen, Geert Uytterhoeven, linux-kernel,
devicetree, linux-mips, letux-kernel, kernel
[-- Attachment #1: Type: text/plain, Size: 2500 bytes --]
On Sat, 22 Feb 2020 11:25:37 +0100
"H. Nikolaus Schaller" <hns@goldelico.com> wrote:
> From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>
> This patch brings support for the JZ4780 efuse. Currently it only exposes
> a read only access to the entire 8K bits efuse memory.
>
> Tested-by: Mathieu Malaterre <malat@debian.org>
> Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> Signed-off-by: Mathieu Malaterre <malat@debian.org>
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> [converted to yaml]
> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> ---
> .../bindings/nvmem/ingenic,jz4780-efuse.yaml | 50 +++++++++++++++++++
> 1 file changed, 50 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>
> diff --git a/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
> new file mode 100644
> index 000000000000..09a8ef937750
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
> @@ -0,0 +1,50 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/nvmem/ingenic,jz4780-efuse.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Ingenic JZ EFUSE driver bindings
> +
> +maintainers:
> + - PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> +
> +allOf:
> + - $ref: "nvmem.yaml#"
> +
> +properties:
> + compatible:
> + enum:
> + - ingenic,jz4780-efuse
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + # Handle for the ahb for the efuse.
> + maxItems: 1
> +
> + clock-names:
> + items:
> + - const: ahb2
as Rob said: probably not needed, since it is a single
clock, and the driver uses devm_clk_get(dev, NULL), so it should be prepared
for that without any extra work.
> +
> +required:
> + - compatible
> + - reg
> + - clock-names
so it is not required here (but "- clocks" (not "- clock") as said in earlier
mail).
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/jz4780-cgu.h>
> +
> + efuse@134100d0 {
> + compatible = "ingenic,jz4780-efuse";
> + reg = <0x134100d0 0x2c>;
> +
> + clocks = <&cgu JZ4780_CLK_AHB2>;
> + clock-names = "ahb2";
and not required here.
Regards,
Andreas
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH v5 2/6] Bindings: nvmem: add bindings for JZ4780 efuse
2020-02-22 15:57 ` Andreas Kemnade
@ 2020-02-22 16:34 ` H. Nikolaus Schaller
2020-02-22 16:46 ` Andreas Kemnade
2020-02-24 7:33 ` Andreas Kemnade
0 siblings, 2 replies; 17+ messages in thread
From: H. Nikolaus Schaller @ 2020-02-22 16:34 UTC (permalink / raw)
To: Andreas Kemnade
Cc: PrasannaKumar Muralidharan, Paul Cercueil, Mathieu Malaterre,
Srinivas Kandagatla, Rob Herring, Mark Rutland, Ralf Baechle,
Paul Burton, Mauro Carvalho Chehab, David S. Miller,
Greg Kroah-Hartman, Jonathan Cameron, Krzysztof Kozlowski,
Kees Cook, Andi Kleen, Geert Uytterhoeven, linux-kernel,
devicetree, linux-mips, letux-kernel, kernel
> Am 22.02.2020 um 16:57 schrieb Andreas Kemnade <andreas@kemnade.info>:
>
> On Sat, 22 Feb 2020 11:25:37 +0100
> "H. Nikolaus Schaller" <hns@goldelico.com> wrote:
>
>> From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>>
>> This patch brings support for the JZ4780 efuse. Currently it only exposes
>> a read only access to the entire 8K bits efuse memory.
>>
>> Tested-by: Mathieu Malaterre <malat@debian.org>
>> Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>> Signed-off-by: Mathieu Malaterre <malat@debian.org>
>> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
>> [converted to yaml]
>> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
>> ---
>> .../bindings/nvmem/ingenic,jz4780-efuse.yaml | 50 +++++++++++++++++++
>> 1 file changed, 50 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>> new file mode 100644
>> index 000000000000..09a8ef937750
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>> @@ -0,0 +1,50 @@
>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/nvmem/ingenic,jz4780-efuse.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Ingenic JZ EFUSE driver bindings
>> +
>> +maintainers:
>> + - PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>> +
>> +allOf:
>> + - $ref: "nvmem.yaml#"
>> +
>> +properties:
>> + compatible:
>> + enum:
>> + - ingenic,jz4780-efuse
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + clocks:
>> + # Handle for the ahb for the efuse.
>> + maxItems: 1
>> +
>> + clock-names:
>> + items:
>> + - const: ahb2
> as Rob said: probably not needed, since it is a single
> clock, and the driver uses devm_clk_get(dev, NULL), so it should be prepared
> for that without any extra work.
The question is if a specific driver implementation should determine
what the DT requires or the other way round. I don't know...
I did interpret Rob's comment differently: there was
> - "clock-names" Must be "bus_clk"
and he did say:
'clk' is redundant. How about 'ahb'?
So I thought he refers to the _clk suffix?
>
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - clock-names
> so it is not required here (but "- clocks" (not "- clock") as said in earlier
> mail).
Well, this is another example where I do not yet see any improvement by yaml.
It is the same amount of guessing what should be written where. Is this to
be added or not? When is it and why, when not and why?
BR and thanks,
Nikolaus
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v5 2/6] Bindings: nvmem: add bindings for JZ4780 efuse
2020-02-22 16:34 ` H. Nikolaus Schaller
@ 2020-02-22 16:46 ` Andreas Kemnade
2020-02-22 17:17 ` H. Nikolaus Schaller
2020-02-24 7:33 ` Andreas Kemnade
1 sibling, 1 reply; 17+ messages in thread
From: Andreas Kemnade @ 2020-02-22 16:46 UTC (permalink / raw)
To: H. Nikolaus Schaller
Cc: PrasannaKumar Muralidharan, Paul Cercueil, Mathieu Malaterre,
Srinivas Kandagatla, Rob Herring, Mark Rutland, Ralf Baechle,
Paul Burton, Mauro Carvalho Chehab, David S. Miller,
Greg Kroah-Hartman, Jonathan Cameron, Krzysztof Kozlowski,
Kees Cook, Andi Kleen, Geert Uytterhoeven, linux-kernel,
devicetree, linux-mips, letux-kernel, kernel
[-- Attachment #1: Type: text/plain, Size: 2916 bytes --]
On Sat, 22 Feb 2020 17:34:06 +0100
"H. Nikolaus Schaller" <hns@goldelico.com> wrote:
> > Am 22.02.2020 um 16:57 schrieb Andreas Kemnade <andreas@kemnade.info>:
> >
> > On Sat, 22 Feb 2020 11:25:37 +0100
> > "H. Nikolaus Schaller" <hns@goldelico.com> wrote:
> >
> >> From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> >>
> >> This patch brings support for the JZ4780 efuse. Currently it only exposes
> >> a read only access to the entire 8K bits efuse memory.
> >>
> >> Tested-by: Mathieu Malaterre <malat@debian.org>
> >> Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> >> Signed-off-by: Mathieu Malaterre <malat@debian.org>
> >> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> >> [converted to yaml]
> >> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> >> ---
> >> .../bindings/nvmem/ingenic,jz4780-efuse.yaml | 50 +++++++++++++++++++
> >> 1 file changed, 50 insertions(+)
> >> create mode 100644 Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
> >>
> >> diff --git a/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
> >> new file mode 100644
> >> index 000000000000..09a8ef937750
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
> >> @@ -0,0 +1,50 @@
> >> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> >> +%YAML 1.2
> >> +---
> >> +$id: http://devicetree.org/schemas/nvmem/ingenic,jz4780-efuse.yaml#
> >> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >> +
> >> +title: Ingenic JZ EFUSE driver bindings
> >> +
> >> +maintainers:
> >> + - PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> >> +
> >> +allOf:
> >> + - $ref: "nvmem.yaml#"
> >> +
> >> +properties:
> >> + compatible:
> >> + enum:
> >> + - ingenic,jz4780-efuse
> >> +
> >> + reg:
> >> + maxItems: 1
> >> +
> >> + clocks:
> >> + # Handle for the ahb for the efuse.
> >> + maxItems: 1
> >> +
> >> + clock-names:
> >> + items:
> >> + - const: ahb2
> > as Rob said: probably not needed, since it is a single
> > clock, and the driver uses devm_clk_get(dev, NULL), so it should be prepared
> > for that without any extra work.
>
> The question is if a specific driver implementation should determine
> what the DT requires or the other way round. I don't know...
>
> I did interpret Rob's comment differently: there was
>
> > - "clock-names" Must be "bus_clk"
>
> and he did say:
>
> 'clk' is redundant. How about 'ahb'?
>
> So I thought he refers to the _clk suffix?
>
and he said to my first try:
---
> + clock-names:
> + items:
> + - const: bus_clk
My prior comment still applies.
Also, for a single clock, you don't really need a name.
---
Regards,
Andreas
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v5 2/6] Bindings: nvmem: add bindings for JZ4780 efuse
2020-02-22 16:46 ` Andreas Kemnade
@ 2020-02-22 17:17 ` H. Nikolaus Schaller
0 siblings, 0 replies; 17+ messages in thread
From: H. Nikolaus Schaller @ 2020-02-22 17:17 UTC (permalink / raw)
To: Andreas Kemnade
Cc: PrasannaKumar Muralidharan, Paul Cercueil, Mathieu Malaterre,
Srinivas Kandagatla, Rob Herring, Mark Rutland, Ralf Baechle,
Paul Burton, Mauro Carvalho Chehab, David S. Miller,
Greg Kroah-Hartman, Jonathan Cameron, Krzysztof Kozlowski,
Kees Cook, Andi Kleen, Geert Uytterhoeven, linux-kernel,
devicetree, linux-mips, letux-kernel, kernel
> Am 22.02.2020 um 17:46 schrieb Andreas Kemnade <andreas@kemnade.info>:
>
> On Sat, 22 Feb 2020 17:34:06 +0100
> "H. Nikolaus Schaller" <hns@goldelico.com> wrote:
>
>>> Am 22.02.2020 um 16:57 schrieb Andreas Kemnade <andreas@kemnade.info>:
>>>
>>> On Sat, 22 Feb 2020 11:25:37 +0100
>>> "H. Nikolaus Schaller" <hns@goldelico.com> wrote:
>>>
>>>> From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>>>>
>>>> This patch brings support for the JZ4780 efuse. Currently it only exposes
>>>> a read only access to the entire 8K bits efuse memory.
>>>>
>>>> Tested-by: Mathieu Malaterre <malat@debian.org>
>>>> Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>>>> Signed-off-by: Mathieu Malaterre <malat@debian.org>
>>>> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
>>>> [converted to yaml]
>>>> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
>>>> ---
>>>> .../bindings/nvmem/ingenic,jz4780-efuse.yaml | 50 +++++++++++++++++++
>>>> 1 file changed, 50 insertions(+)
>>>> create mode 100644 Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>>>> new file mode 100644
>>>> index 000000000000..09a8ef937750
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
>>>> @@ -0,0 +1,50 @@
>>>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>>>> +%YAML 1.2
>>>> +---
>>>> +$id: http://devicetree.org/schemas/nvmem/ingenic,jz4780-efuse.yaml#
>>>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>>>> +
>>>> +title: Ingenic JZ EFUSE driver bindings
>>>> +
>>>> +maintainers:
>>>> + - PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
>>>> +
>>>> +allOf:
>>>> + - $ref: "nvmem.yaml#"
>>>> +
>>>> +properties:
>>>> + compatible:
>>>> + enum:
>>>> + - ingenic,jz4780-efuse
>>>> +
>>>> + reg:
>>>> + maxItems: 1
>>>> +
>>>> + clocks:
>>>> + # Handle for the ahb for the efuse.
>>>> + maxItems: 1
>>>> +
>>>> + clock-names:
>>>> + items:
>>>> + - const: ahb2
>>> as Rob said: probably not needed, since it is a single
>>> clock, and the driver uses devm_clk_get(dev, NULL), so it should be prepared
>>> for that without any extra work.
>>
>> The question is if a specific driver implementation should determine
>> what the DT requires or the other way round. I don't know...
>>
>> I did interpret Rob's comment differently: there was
>>
>>> - "clock-names" Must be "bus_clk"
>>
>> and he did say:
>>
>> 'clk' is redundant. How about 'ahb'?
>>
>> So I thought he refers to the _clk suffix?
>>
>
> and he said to my first try:
> ---
>> + clock-names:
>> + items:
>> + - const: bus_clk
>
> My prior comment still applies.
>
> Also, for a single clock, you don't really need a name.
Ah, ok. I may have missed that.
BR and thanks,
Nikolaus
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v5 2/6] Bindings: nvmem: add bindings for JZ4780 efuse
2020-02-22 16:34 ` H. Nikolaus Schaller
2020-02-22 16:46 ` Andreas Kemnade
@ 2020-02-24 7:33 ` Andreas Kemnade
1 sibling, 0 replies; 17+ messages in thread
From: Andreas Kemnade @ 2020-02-24 7:33 UTC (permalink / raw)
To: H. Nikolaus Schaller
Cc: PrasannaKumar Muralidharan, Paul Cercueil, Mathieu Malaterre,
Srinivas Kandagatla, Rob Herring, Mark Rutland, Ralf Baechle,
Paul Burton, Mauro Carvalho Chehab, David S. Miller,
Greg Kroah-Hartman, Jonathan Cameron, Krzysztof Kozlowski,
Kees Cook, Andi Kleen, Geert Uytterhoeven, linux-kernel,
devicetree, linux-mips, letux-kernel, kernel
[-- Attachment #1: Type: text/plain, Size: 3473 bytes --]
On Sat, 22 Feb 2020 17:34:06 +0100
"H. Nikolaus Schaller" <hns@goldelico.com> wrote:
> > Am 22.02.2020 um 16:57 schrieb Andreas Kemnade <andreas@kemnade.info>:
> >
> > On Sat, 22 Feb 2020 11:25:37 +0100
> > "H. Nikolaus Schaller" <hns@goldelico.com> wrote:
> >
> >> From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> >>
> >> This patch brings support for the JZ4780 efuse. Currently it only exposes
> >> a read only access to the entire 8K bits efuse memory.
> >>
> >> Tested-by: Mathieu Malaterre <malat@debian.org>
> >> Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> >> Signed-off-by: Mathieu Malaterre <malat@debian.org>
> >> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> >> [converted to yaml]
> >> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> >> ---
> >> .../bindings/nvmem/ingenic,jz4780-efuse.yaml | 50 +++++++++++++++++++
> >> 1 file changed, 50 insertions(+)
> >> create mode 100644 Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
> >>
> >> diff --git a/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
> >> new file mode 100644
> >> index 000000000000..09a8ef937750
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/nvmem/ingenic,jz4780-efuse.yaml
> >> @@ -0,0 +1,50 @@
> >> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> >> +%YAML 1.2
> >> +---
> >> +$id: http://devicetree.org/schemas/nvmem/ingenic,jz4780-efuse.yaml#
> >> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >> +
> >> +title: Ingenic JZ EFUSE driver bindings
> >> +
> >> +maintainers:
> >> + - PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
> >> +
> >> +allOf:
> >> + - $ref: "nvmem.yaml#"
> >> +
> >> +properties:
> >> + compatible:
> >> + enum:
> >> + - ingenic,jz4780-efuse
> >> +
> >> + reg:
> >> + maxItems: 1
> >> +
> >> + clocks:
> >> + # Handle for the ahb for the efuse.
> >> + maxItems: 1
> >> +
> >> + clock-names:
> >> + items:
> >> + - const: ahb2
> > as Rob said: probably not needed, since it is a single
> > clock, and the driver uses devm_clk_get(dev, NULL), so it should be prepared
> > for that without any extra work.
>
> The question is if a specific driver implementation should determine
> what the DT requires or the other way round. I don't know...
>
> I did interpret Rob's comment differently: there was
>
> > - "clock-names" Must be "bus_clk"
>
> and he did say:
>
> 'clk' is redundant. How about 'ahb'?
>
> So I thought he refers to the _clk suffix?
>
> >
> >> +
> >> +required:
> >> + - compatible
> >> + - reg
> >> + - clock-names
> > so it is not required here (but "- clocks" (not "- clock") as said in earlier
> > mail).
>
> Well, this is another example where I do not yet see any improvement by yaml.
> It is the same amount of guessing what should be written where. Is this to
> be added or not? When is it and why, when not and why?
>
well, this is the list of required properties which have to be an any
devicetree using that device, the conversion of the comments for the properties
in the .txt-file.
So, if you do not declare a property before, you cannot specify that it is
required. So if we drop the definition of clock-names we cannot declare it
as required.
Regards,
Andreas
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH v5 3/6] Documentation: ABI: nvmem: add documentation for JZ4780 efuse ABI
2020-02-22 10:25 [PATCH v5 0/6] MIPS: CI20: Add efuse driver for Ingenic JZ4780 and attach to DM9000 for stable MAC addresses H. Nikolaus Schaller
2020-02-22 10:25 ` [PATCH v5 1/6] nvmem: add driver for JZ4780 efuse H. Nikolaus Schaller
2020-02-22 10:25 ` [PATCH v5 2/6] Bindings: nvmem: add bindings " H. Nikolaus Schaller
@ 2020-02-22 10:25 ` H. Nikolaus Schaller
2020-02-22 10:25 ` [PATCH v5 4/6] nvmem: MAINTAINERS: add maintainer for JZ4780 efuse driver H. Nikolaus Schaller
` (2 subsequent siblings)
5 siblings, 0 replies; 17+ messages in thread
From: H. Nikolaus Schaller @ 2020-02-22 10:25 UTC (permalink / raw)
To: PrasannaKumar Muralidharan, Andreas Kemnade, Paul Cercueil,
Mathieu Malaterre, Srinivas Kandagatla, Rob Herring,
Mark Rutland, Ralf Baechle, Paul Burton, Mauro Carvalho Chehab,
David S. Miller, Greg Kroah-Hartman, Jonathan Cameron,
H. Nikolaus Schaller, Krzysztof Kozlowski, Kees Cook, Andi Kleen,
Geert Uytterhoeven
Cc: linux-kernel, devicetree, linux-mips, letux-kernel, kernel
From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
---
.../ABI/testing/sysfs-driver-jz4780-efuse | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
create mode 100644 Documentation/ABI/testing/sysfs-driver-jz4780-efuse
diff --git a/Documentation/ABI/testing/sysfs-driver-jz4780-efuse b/Documentation/ABI/testing/sysfs-driver-jz4780-efuse
new file mode 100644
index 000000000000..bb6f5d6ceea0
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-jz4780-efuse
@@ -0,0 +1,16 @@
+What: /sys/devices/*/<our-device>/nvmem
+Date: December 2017
+Contact: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
+Description: read-only access to the efuse on the Ingenic JZ4780 SoC
+ The SoC has a one time programmable 8K efuse that is
+ split into segments. The driver supports read only.
+ The segments are
+ 0x000 64 bit Random Number
+ 0x008 128 bit Ingenic Chip ID
+ 0x018 128 bit Customer ID
+ 0x028 3520 bit Reserved
+ 0x1E0 8 bit Protect Segment
+ 0x1E1 2296 bit HDMI Key
+ 0x300 2048 bit Security boot key
+Users: any user space application which wants to read the Chip
+ and Customer ID
--
2.23.0
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v5 4/6] nvmem: MAINTAINERS: add maintainer for JZ4780 efuse driver
2020-02-22 10:25 [PATCH v5 0/6] MIPS: CI20: Add efuse driver for Ingenic JZ4780 and attach to DM9000 for stable MAC addresses H. Nikolaus Schaller
` (2 preceding siblings ...)
2020-02-22 10:25 ` [PATCH v5 3/6] Documentation: ABI: nvmem: add documentation for JZ4780 efuse ABI H. Nikolaus Schaller
@ 2020-02-22 10:25 ` H. Nikolaus Schaller
2020-02-22 10:25 ` [PATCH v5 5/6] MIPS: DTS: JZ4780: define node for JZ4780 efuse H. Nikolaus Schaller
2020-02-22 10:25 ` [PATCH v5 6/6] MIPS: DTS: CI20: make DM9000 Ethernet controller use NVMEM to find the default MAC address H. Nikolaus Schaller
5 siblings, 0 replies; 17+ messages in thread
From: H. Nikolaus Schaller @ 2020-02-22 10:25 UTC (permalink / raw)
To: PrasannaKumar Muralidharan, Andreas Kemnade, Paul Cercueil,
Mathieu Malaterre, Srinivas Kandagatla, Rob Herring,
Mark Rutland, Ralf Baechle, Paul Burton, Mauro Carvalho Chehab,
David S. Miller, Greg Kroah-Hartman, Jonathan Cameron,
H. Nikolaus Schaller, Krzysztof Kozlowski, Kees Cook, Andi Kleen,
Geert Uytterhoeven
Cc: linux-kernel, devicetree, linux-mips, letux-kernel, kernel
From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
---
MAINTAINERS | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index a0d86490c2c6..5bab216d8fe9 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8270,6 +8270,11 @@ M: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
S: Maintained
F: drivers/dma/dma-jz4780.c
+INGENIC JZ4780 EFUSE Driver
+M: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
+S: Maintained
+F: drivers/nvmem/jz4780-efuse.c
+
INGENIC JZ4780 NAND DRIVER
M: Harvey Hunt <harveyhuntnexus@gmail.com>
L: linux-mtd@lists.infradead.org
--
2.23.0
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v5 5/6] MIPS: DTS: JZ4780: define node for JZ4780 efuse
2020-02-22 10:25 [PATCH v5 0/6] MIPS: CI20: Add efuse driver for Ingenic JZ4780 and attach to DM9000 for stable MAC addresses H. Nikolaus Schaller
` (3 preceding siblings ...)
2020-02-22 10:25 ` [PATCH v5 4/6] nvmem: MAINTAINERS: add maintainer for JZ4780 efuse driver H. Nikolaus Schaller
@ 2020-02-22 10:25 ` H. Nikolaus Schaller
2020-02-22 10:25 ` [PATCH v5 6/6] MIPS: DTS: CI20: make DM9000 Ethernet controller use NVMEM to find the default MAC address H. Nikolaus Schaller
5 siblings, 0 replies; 17+ messages in thread
From: H. Nikolaus Schaller @ 2020-02-22 10:25 UTC (permalink / raw)
To: PrasannaKumar Muralidharan, Andreas Kemnade, Paul Cercueil,
Mathieu Malaterre, Srinivas Kandagatla, Rob Herring,
Mark Rutland, Ralf Baechle, Paul Burton, Mauro Carvalho Chehab,
David S. Miller, Greg Kroah-Hartman, Jonathan Cameron,
H. Nikolaus Schaller, Krzysztof Kozlowski, Kees Cook, Andi Kleen,
Geert Uytterhoeven
Cc: linux-kernel, devicetree, linux-mips, letux-kernel, kernel
From: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory and the
ethernet mac address for the davicom dm9000 chip on the CI20 board.
It also changes the nemc reg range to avoid overlap.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
arch/mips/boot/dts/ingenic/jz4780.dtsi | 17 ++++++++++++++++-
1 file changed, 16 insertions(+), 1 deletion(-)
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
index f928329b034b..1e266be28096 100644
--- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
@@ -358,7 +358,7 @@
nemc: nemc@13410000 {
compatible = "ingenic,jz4780-nemc";
- reg = <0x13410000 0x10000>;
+ reg = <0x13410000 0x4c>;
#address-cells = <2>;
#size-cells = <1>;
ranges = <1 0 0x1b000000 0x1000000
@@ -373,6 +373,21 @@
status = "disabled";
};
+ efuse: efuse@134100d0 {
+ compatible = "ingenic,jz4780-efuse";
+ reg = <0x134100d0 0x2c>;
+
+ clocks = <&cgu JZ4780_CLK_AHB2>;
+ clock-names = "ahb2";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eth0_addr: eth-mac-addr@0x22 {
+ reg = <0x22 0x6>;
+ };
+ };
+
dma: dma@13420000 {
compatible = "ingenic,jz4780-dma";
reg = <0x13420000 0x400
--
2.23.0
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v5 6/6] MIPS: DTS: CI20: make DM9000 Ethernet controller use NVMEM to find the default MAC address
2020-02-22 10:25 [PATCH v5 0/6] MIPS: CI20: Add efuse driver for Ingenic JZ4780 and attach to DM9000 for stable MAC addresses H. Nikolaus Schaller
` (4 preceding siblings ...)
2020-02-22 10:25 ` [PATCH v5 5/6] MIPS: DTS: JZ4780: define node for JZ4780 efuse H. Nikolaus Schaller
@ 2020-02-22 10:25 ` H. Nikolaus Schaller
5 siblings, 0 replies; 17+ messages in thread
From: H. Nikolaus Schaller @ 2020-02-22 10:25 UTC (permalink / raw)
To: PrasannaKumar Muralidharan, Andreas Kemnade, Paul Cercueil,
Mathieu Malaterre, Srinivas Kandagatla, Rob Herring,
Mark Rutland, Ralf Baechle, Paul Burton, Mauro Carvalho Chehab,
David S. Miller, Greg Kroah-Hartman, Jonathan Cameron,
H. Nikolaus Schaller, Krzysztof Kozlowski, Kees Cook, Andi Kleen,
Geert Uytterhoeven
Cc: linux-kernel, devicetree, linux-mips, letux-kernel, kernel
There is a unique MAC address programmed into the eFuses
of the JZ4780 chip in the CI20 factory. By using this
for initializing the DM9000 Ethernet controller, every
CI20 board has an individual - but stable - MAC address
and DHCP can assign stable IP addresses.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
arch/mips/boot/dts/ingenic/ci20.dts | 3 +++
1 file changed, 3 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
index 37b93166bf22..6dc1f9eeff00 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -355,6 +355,9 @@
interrupt-parent = <&gpe>;
interrupts = <19 4>;
+
+ nvmem-cells = <ð0_addr>;
+ nvmem-cell-names = "mac-address";
};
};
--
2.23.0
^ permalink raw reply related [flat|nested] 17+ messages in thread