Re: USB storage does not work with 3GB of RAM, but does with 2G of RAM

Re: USB storage does not work with 3GB of RAM, but does with 2G of RAM

[Andi Kleen]

"Jon Schindler" <jonschindler@hotmail.com> writes:
> 
> This mainly seems to be an issue with USB mass storage devices like
> USB memory sticks and USB hard drives (I've tried both, and neither is
> assigned a scsi device properly).  I am still able to use my USB mouse
> when I have 3GB installed.  I'm not sure if that makes it a USB 1.1
> issue or a USB storage issue, but hopefully someone will have some
> insight after looking at the logs.  Thanks in advance for any help.

It sounds like the Nvidia EHCI controller has trouble DMAing to high
addresses. Would be a bad bug if true.

Does it work when you disable EHCI and only enable OHCI? (this will
limit you to USB 1.1) 

-Andi

Re: USB storage does not work with 3GB of RAM, but does with 2G of RAM

[Jon Schindler]

Hi Andi,

Thanks for the quick reply.  I'm at work, so I won't be able to test USB 
until I get home in a few hours.  I have an ssh connection to the machine, 
but that's it for now.  Just in case you are wondering what address it's 
using for DMA, below it a copy of my lspci -v.

Thanks again for replying.

Jon

00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Flags: bus master, 66Mhz, fast devsel, latency 0
	Memory at f0000000 (32-bit, prefetchable) [size=128M]
	Capabilities: [44] HyperTransport: Slave or Primary Interface
	Capabilities: [c0] AGP version 3.0

00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Flags: bus master, 66Mhz, fast devsel, latency 0

00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management (rev 
a1)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Flags: 66Mhz, fast devsel, IRQ 11
	I/O ports at fc00 [size=32]
	I/O ports at 4c00 [size=64]
	I/O ports at 4c40 [size=64]
	Capabilities: [44] Power Management version 2

00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) 
(prog-if 10 [OHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 185
	Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2

00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) 
(prog-if 10 [OHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 193
	Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2

00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 Controller 
(rev a2) (prog-if 20 [EHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 177
	Memory at fe02d000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [44] Debug port
	Capabilities: [80] Power Management version 2

00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 193
	Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
	I/O ports at f000 [size=8]
	Capabilities: [44] Power Management version 2

00:06.0 Multimedia audio controller: nVidia Corporation nForce3 250Gb AC'97 
Audio Controller (rev a1)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 7585
	Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 209
	I/O ports at ec00 [size=256]
	I/O ports at e800 [size=128]
	Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2

00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller 
(v2.5) (rev a2) (prog-if 8a [Master SecP PriP])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Flags: bus master, 66Mhz, fast devsel, latency 0
	I/O ports at dc00 [size=16]
	Capabilities: [44] Power Management version 2

00:09.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller (v2.5) 
(rev a2) (prog-if 85 [Master SecO PriO])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 177
	I/O ports at 09e0 [size=8]
	I/O ports at 0be0 [size=4]
	I/O ports at 0960 [size=8]
	I/O ports at 0b60 [size=4]
	I/O ports at c800 [size=16]
	I/O ports at c400 [size=128]
	Capabilities: [44] Power Management version 2

00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller (v2.5) 
(rev a2) (prog-if 85 [Master SecO PriO])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Flags: bus master, 66Mhz, fast devsel, latency 0, IRQ 185
	I/O ports at 09f0 [size=8]
	I/O ports at 0bf0 [size=4]
	I/O ports at 0970 [size=8]
	I/O ports at 0b70 [size=4]
	I/O ports at b000 [size=16]
	I/O ports at ac00 [size=128]
	Capabilities: [44] Power Management version 2

00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge 
(rev a2) (prog-if 00 [Normal decode])
	Flags: bus master, 66Mhz, medium devsel, latency 16
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=10
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: fa000000-fcffffff
	Prefetchable memory behind bridge: e0000000-efffffff

00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge (rev 
a2) (prog-if 00 [Normal decode])
	Flags: bus master, 66Mhz, fast devsel, latency 0
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=128
	I/O behind bridge: 00008000-00008fff
	Memory behind bridge: fdf00000-fdffffff
	Prefetchable memory behind bridge: fde00000-fdefffff

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] 
HyperTransport Technology Configuration
	Flags: fast devsel
	Capabilities: [80] HyperTransport: Host or Secondary Interface

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] 
Address Map
	Flags: fast devsel

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM 
Controller
	Flags: fast devsel

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] 
Miscellaneous Control
	Flags: fast devsel

01:00.0 VGA compatible controller: nVidia Corporation NV40 [GeForce 6800 GT] 
(rev a1) (prog-if 00 [VGA])
	Flags: bus master, 66Mhz, medium devsel, latency 248, IRQ 201
	Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
	Memory at e0000000 (32-bit, prefetchable) [size=256M]
	Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [60] Power Management version 2
	Capabilities: [44] AGP version 3.0

02:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video 
Capture (rev 02)
	Subsystem: ATI Technologies Inc: Unknown device 0001
	Flags: bus master, medium devsel, latency 32, IRQ 217
	Memory at fdeff000 (32-bit, prefetchable) [size=4K]

02:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture 
(rev 02)
	Subsystem: ATI Technologies Inc TV-Wonder
	Flags: bus master, medium devsel, latency 32, IRQ 217
	Memory at fdefe000 (32-bit, prefetchable) [size=4K]

02:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host 
Controller (rev 46) (prog-if 10 [OHCI])
	Subsystem: Unknown device 0574:086c
	Flags: bus master, stepping, medium devsel, latency 32, IRQ 225
	Memory at fdfff000 (32-bit, non-prefetchable) [size=2K]
	I/O ports at 8c00 [size=128]
	Capabilities: [50] Power Management version 2

02:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 
Gigabit Ethernet (rev 10)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 025c
	Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 201
	I/O ports at 8800 [size=256]
	Memory at fdffe000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [dc] Power Management version 2



>From: Andi Kleen <ak@suse.de>
>To: "Jon Schindler" <jonschindler@hotmail.com>
>CC: linux-kernel@vger.kernel.org
>Subject: Re: USB storage does not work with 3GB of RAM, but does with 2G of 
>RAM
>Date: 08 Jul 2005 21:29:37 +0200
>
>"Jon Schindler" <jonschindler@hotmail.com> writes:
> >
> > This mainly seems to be an issue with USB mass storage devices like
> > USB memory sticks and USB hard drives (I've tried both, and neither is
> > assigned a scsi device properly).  I am still able to use my USB mouse
> > when I have 3GB installed.  I'm not sure if that makes it a USB 1.1
> > issue or a USB storage issue, but hopefully someone will have some
> > insight after looking at the logs.  Thanks in advance for any help.
>
>It sounds like the Nvidia EHCI controller has trouble DMAing to high
>addresses. Would be a bad bug if true.
>
>Does it work when you disable EHCI and only enable OHCI? (this will
>limit you to USB 1.1)
>
>-Andi

Re: USB storage does not work with 3GB of RAM, but does with 2G of RAM

[Jon Schindler]

I just thought that I would add, USB works fine if I boot with knoppix 3.9, 
or with Windows XP, even with 3GB's of RAM installed.  It's only if I try to 
use USB mass storage devices, Fedora Core 4 64 bit, and 3GB's of RAM at the 
same time that I get this issue with USB.  If I change the OS to XP, but 
keep the RAM at 3GB, it works fine.  If I remove some RAM and only run 2GB's 
of RAM, then FC4 with the 2.6.12.1 64 bit kernel works fine.
So, to sum things up:
       RAM amount                OS            64or32bit               USB 
storage works?
            3GB                    FC4 2.6.12.1        64                    
          no
            2GB                    FC4 2.6.12.1        64                    
          yes
            3GB                         XP SP2           32                  
            yes
            2GB                         XP SP2           32                  
            yes
            3GB                  Knoppix 3.9           32                    
          yes
            2GB                  Knoppix 3.9           32                    
          yes

Thanks again,

Jon


>From: Andi Kleen <ak@suse.de>
>To: "Jon Schindler" <jonschindler@hotmail.com>
>CC: linux-kernel@vger.kernel.org
>Subject: Re: USB storage does not work with 3GB of RAM, but does with 2G of 
>RAM
>Date: 08 Jul 2005 21:29:37 +0200
>
>"Jon Schindler" <jonschindler@hotmail.com> writes:
> >
> > This mainly seems to be an issue with USB mass storage devices like
> > USB memory sticks and USB hard drives (I've tried both, and neither is
> > assigned a scsi device properly).  I am still able to use my USB mouse
> > when I have 3GB installed.  I'm not sure if that makes it a USB 1.1
> > issue or a USB storage issue, but hopefully someone will have some
> > insight after looking at the logs.  Thanks in advance for any help.
>
>It sounds like the Nvidia EHCI controller has trouble DMAing to high
>addresses. Would be a bad bug if true.
>
>Does it work when you disable EHCI and only enable OHCI? (this will
>limit you to USB 1.1)
>
>-Andi

Re: USB storage does not work with 3GB of RAM, but does with 2G of RAM

[Jon Schindler]

Hi Andi,

As you suggested, removing ehci_hcd (using rmmod ehci_hcd) allows the USB 
storage device to work.  So, to answer your question, yes, the ohci_hcd 
driver does work with 3GB's of RAM.  Still, knoppix 3.9 IS able to work with 
both ehci and 3GB's of RAM, so it still sounds like it's a software problem, 
not an nvidia hardware issue.

Jon

>From: Andi Kleen <ak@suse.de>
>To: "Jon Schindler" <jonschindler@hotmail.com>
>CC: linux-kernel@vger.kernel.org
>Subject: Re: USB storage does not work with 3GB of RAM, but does with 2G of 
>RAM
>Date: 08 Jul 2005 21:29:37 +0200
>
>"Jon Schindler" <jonschindler@hotmail.com> writes:
> >
> > This mainly seems to be an issue with USB mass storage devices like
> > USB memory sticks and USB hard drives (I've tried both, and neither is
> > assigned a scsi device properly).  I am still able to use my USB mouse
> > when I have 3GB installed.  I'm not sure if that makes it a USB 1.1
> > issue or a USB storage issue, but hopefully someone will have some
> > insight after looking at the logs.  Thanks in advance for any help.
>
>It sounds like the Nvidia EHCI controller has trouble DMAing to high
>addresses. Would be a bad bug if true.
>
>Does it work when you disable EHCI and only enable OHCI? (this will
>limit you to USB 1.1)
>
>-Andi
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at  http://www.tux.org/lkml/

Re: USB storage does not work with 3GB of RAM, but does with 2G of RAM

[Andi Kleen]

On Fri, Jul 08, 2005 at 08:49:12PM -0400, Jon Schindler wrote:
> Hi Andi,
> 
> As you suggested, removing ehci_hcd (using rmmod ehci_hcd) allows the USB 
> storage device to work.  So, to answer your question, yes, the ohci_hcd 
> driver does work with 3GB's of RAM.  Still, knoppix 3.9 IS able to work 
> with both ehci and 3GB's of RAM, so it still sounds like it's a software 
> problem, not an nvidia hardware issue.

Knoppix is 32bit I guess. The 32bit kernel will do a lot of DMA
only in the first 800-900MB (lowmem) 

-Andi

Re: USB storage does not work with 3GB of RAM, but does with 2G of RAM

[Jon Schindler]

Do you know if there is a way to tell the ehci driver to do the DMA at a 
lower memory address?  i.e. tell the kernel to reserve a block of memory (as 
a boot option) and then tell the ehci driver to use that area of RAM 
instead?

Thanks again for your help,

Jon

>From: Andi Kleen <ak@suse.de>
>To: Jon Schindler <jonschindler@hotmail.com>
>CC: ak@suse.de, linux-kernel@vger.kernel.org
>Subject: Re: USB storage does not work with 3GB of RAM, but does with 2G of 
>RAM
>Date: Sat, 9 Jul 2005 02:56:38 +0200
>
>On Fri, Jul 08, 2005 at 08:49:12PM -0400, Jon Schindler wrote:
> > Hi Andi,
> >
> > As you suggested, removing ehci_hcd (using rmmod ehci_hcd) allows the 
>USB
> > storage device to work.  So, to answer your question, yes, the ohci_hcd
> > driver does work with 3GB's of RAM.  Still, knoppix 3.9 IS able to work
> > with both ehci and 3GB's of RAM, so it still sounds like it's a software
> > problem, not an nvidia hardware issue.
>
>Knoppix is 32bit I guess. The 32bit kernel will do a lot of DMA
>only in the first 800-900MB (lowmem)
>
>-Andi
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at  http://www.tux.org/lkml/

Re: USB storage does not work with 3GB of RAM, but does with 2G of RAM

[Oliver Weihe]

Tried different settings for "Soft-/Hardware Memory Hole" in BIOS?

Re: USB storage does not work with 3GB of RAM, but does with 2G of RAM

[Jon Schindler]

are you referring to the "OS/2" memory hole option?  No, I haven't tried it, 
but it's an interesting idea.  I'm pretty sure the only memory hole that my 
bios has is the option for OS/2, which I will try tonight.

Thanks,

Jon

>From: Oliver Weihe <o.weihe@deltacomputer.de>
>To: linux-kernel@vger.kernel.org
>Subject: Re: USB storage does not work with 3GB of RAM, but does with 2G of 
>RAM
>Date: Mon, 11 Jul 2005 17:03:24 +0200 (CEST)
>
>Tried different settings for "Soft-/Hardware Memory Hole" in BIOS?
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at  http://www.tux.org/lkml/

Re: USB storage does not work with 3GB of RAM, but does with 2G of RAM

[Jon Schindler]

I tried this last night and enabling the OS2 memory hole in the bios doesn't 
work.  That's the only memory hole option available.  If I were more savvy 
with the kernel memory layout, I might try passing it a set of memmap 
options, but I'm not very familiar with what address spaces I need to set up 
for the kernel or how much space they need, or if there are any rules 
concerning what goes where.  (i.e. the difference between reserved, ACPI, 
etc.)

Thanks anyway for the suggestion,

Jon

>From: Oliver Weihe <o.weihe@deltacomputer.de>
>To: linux-kernel@vger.kernel.org
>Subject: Re: USB storage does not work with 3GB of RAM, but does with 2G of 
>RAM
>Date: Mon, 11 Jul 2005 17:03:24 +0200 (CEST)
>
>Tried different settings for "Soft-/Hardware Memory Hole" in BIOS?
>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at  http://www.tux.org/lkml/

Re: Realtime Preemption, 2.6.12, Beginners Guide?

[Alistair John Strachan]

[-- Attachment #1: Type: text/plain, Size: 1994 bytes --]

On Friday 08 Jul 2005 12:46, Ingo Molnar wrote:
[snip]
>
> Ok. Could you try to debug this some more? In the -51-17 patch i've
> implemented a new stack-overflow debugging feature: 'stack footprint
> maximum searching'. It is automatically active if you have
> CONFIG_LATENCY_TRACE and CONFIG_DEBUG_STACKOVERFLOW enabled. It will
> track and (if it can be done safely) print out maximum stack usage sites
> immediately. Hopefully this results in better stackdumps. It should
> print similar traces:
>
> ----------------------------->
>
> | new stack-footprint maximum: smartd/1747, 1768 bytes.
>
> ------------|
>  [<c013c1b6>] check_raw_flags+0xb/0x55 (8)
>  [<c013ebeb>] sub_preempt_count+0x1a/0x1c (8)
>  [<c013cb28>] __mcount+0x6a/0x91 (28)
>  [<c013c3ff>] irqs_disabled+0x8/0x19 (16)
>  [<c013c7b5>] ____trace+0x9e/0x208 (4)
>  [<c01142d8>] mcount+0x14/0x18 (24)
>  [<c013c3ff>] irqs_disabled+0x8/0x19 (20)
>  [<c013c7b5>] ____trace+0x9e/0x208 (8)
>  [<c013f145>] trace_stop_sched_switched+0x40/0x17d (8)
>  [...]
>
> i've written a separate, hopefully more robust stack-dumper which is
> used for the above traces. Perhaps in your overflow case it results in
> something usable.

Unfortunately I see nothing like this when the machine crashes. Find attached 
my config, which has CONFIG_4KSTACKS and the options you specified. Are you 
sure this is sufficient to enable it?

Here is an extremely bad digital camera pic from the crash. My debugging 
prowess has evolved to the stage where by I'm using a maximum res vesafb 
console.

However, I'm not at work so it's my own digital camera that I'm using rather 
than work's, and it seems to react badly to the LCD. I hope you can read the 
numbers, if not I'll try to transliterate them for you.

http://devzero.co.uk/~alistair/oops5.jpeg

-- 
Cheers,
Alistair.

personal:   alistair()devzero!co!uk
university: s0348365()sms!ed!ac!uk
student:    CS/CSim Undergraduate
contact:    1F2 55 South Clerk Street,
            Edinburgh. EH8 9PP.

[-- Attachment #2: config.gz --]
[-- Type: application/x-gzip, Size: 8558 bytes --]

USB storage does not work with 3GB of RAM, but does with 2G of RAM

[Jon Schindler]

I submitted this bug to both the USB users and developers mailing list, and 
haven't heard anything after waiting several days, so I thought that I would 
try here.  While waiting for a response another user contacted me who is 
having the same problem, so I am not the only person who is running into 
problems with USB storage when using large amounts of RAM.  Below is the 
text of my original submission...

I have just upgraded my RAM, and now have 3GB of total memory.  For some 
reason USB does not work with this amount of RAM.  However, if I remove two 
DIMM's it works again (it works fine with either the 2x1GB DIMMs or 2x512MB 
DIMMS, but not all 4 DIMMS installed).  I'm assuming that it's an issue with 
having over 2GB's of RAM installed.  I will post both of my dmesgs below, 
the first one is when my system has 2GB's of RAM, and the 2nd when my system 
has 3GB's of RAM.  I've already tried adding --no-mem-option to my kernel 
options, to see if maybe grub wasn't feeding the kernel the wrong memory 
layout.  I am running a beta bios 1.9b5 on an MSI K8N neo2 platinum.  I also 
have a dual core athlon 4800+, and am running Fedora Core 4 64 bit edition.  
The USB does work in knoppix 3.9 with 3GB of RAM, but I would like to get 
this working in Fedora Core 4 with 3GB of RAM, not just 2GB.

This mainly seems to be an issue with USB mass storage devices like USB 
memory sticks and USB hard drives (I've tried both, and neither is assigned 
a scsi device properly).  I am still able to use my USB mouse when I have 
3GB installed.  I'm not sure if that makes it a USB 1.1 issue or a USB 
storage issue, but hopefully someone will have some insight after looking at 
the logs.  Thanks in advance for any help.

Jon

dmesg with 2GB of RAM:
Bootdata ok (command line is ro root=LABEL=/1 rhgb 3)
Linux version 2.6.12.1 (root@localhost) (gcc version 4.0.0 20050519 (Red Hat 
4.0.0-8)) #14 SMP Tue Jul 5 00:33:42 CDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS)
BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 Nvidia                                ) @ 
0x00000000000f8e80
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 
0x000000007fff3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 
0x000000007fff30c0
ACPI: SSDT (v001 PTLTD  POWERNOW 0x00000001  LTP 0x00000001) @ 
0x000000007fff7b80
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 
0x000000007fff7ac0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 
0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000007fff0000
Using node hash shift of 24
Bootmem setup node 0 0000000000000000-000000007fff0000
On node 0 totalpages: 524272
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 520176 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
Nvidia board detected. Ignoring ACPI timer override.
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 80000000:7ec00000)
Checking aperture...
CPU 0: aperture @ f0000000 size 128 MB
Built 1 zonelists
Kernel command line: ro root=LABEL=/1 rhgb 3
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 2411.013 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Memory: 2054132k/2097088k available (2382k kernel code, 0k reserved, 1584k 
data, 228k init)
Calibrating delay loop... 4767.74 BogoMIPS (lpj=2383872)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(2) -> Node 0 -> Core 0
Using local APIC timer interrupts.
Detected 12.557 MHz APIC timer.
Booting processor 1/1 rip 6000 rsp ffff810003351f58
Initializing CPU#1
Calibrating delay loop... 4816.89 BogoMIPS (lpj=2408448)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1(2) -> Node 0 -> Core 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ stepping 02
CPU 1: Syncing TSC to CPU 0.
Brought up 2 CPUs
CPU 1: synchronized TSC with CPU 0 (last diff -1 cycles, maxerr 505 cycles)
time.c: Using PIT/TSC based timekeeping.
testing NMI watchdog ... OK.
CPU0 attaching sched-domain:
domain 0: span 00000001
groups: 00000001
domain 1: span 00000003
groups: 00000001 00000002
domain 2: span 00000003
  groups: 00000003
CPU1 attaching sched-domain:
domain 0: span 00000002
groups: 00000002
domain 1: span 00000003
groups: 00000002 00000001
domain 2: span 00000003
  groups: 00000003
checking if image is initramfs... it is
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a 
report
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 128M @ 0xf0000000
PCI-DMA: Disabling IOMMU.
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4800-0x487f has been reserved
pnp: 00:00: ioport range 0x4880-0x48ff has been reserved
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1120524127.297:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
  ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:DMA
  ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y250P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: PLEXTOR DVDR PX-716A, ATAPI CD/DVD-ROM drive
hdd: TOSHIBA DVD-ROM SD-M1212, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63, 
UDMA(133)
hda: cache flushes supported
hda: hda1 hda2
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 32X DVD-ROM drive, 256kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 128Kbytes
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.40.2)
powernow-k8:    0 : fid 0x10 (2400 MHz), vid 0xa (1300 mV)
powernow-k8:    1 : fid 0xe (2200 MHz), vid 0xa (1300 mV)
powernow-k8:    2 : fid 0xc (2000 MHz), vid 0xc (1250 mV)
powernow-k8:    3 : fid 0xa (1800 MHz), vid 0xe (1200 mV)
powernow-k8:    4 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0x10, vid 0xa
ACPI wakeup devices:
HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 228k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
SCSI subsystem initialized
libata version 1.11 loaded.
sata_nv version 0.6
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [APSI] -> GSI 23 (level, high) 
-> IRQ 177
PCI: Setting latency timer of device 0000:00:09.0 to 64
ata1: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC800 irq 177
ata2: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC808 irq 177
ata1: no device found (phy stat 00000000)
scsi0 : sata_nv
input: PS2++ Logitech Wheel Mouse on isa0060/serio1
ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003 
88:203f
ata2: dev 0 ATA, max UDMA/100, 625142448 sectors: lba48
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata2: dev 0 configured for UDMA/100
scsi1 : sata_nv
Vendor: ATA       Model: WDC WD3200SD-01K  Rev: 08.0
Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APSJ] -> GSI 22 (level, high) 
-> IRQ 185
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ata3: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xB000 irq 185
ata4: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xB008 irq 185
ata3: dev 0 cfg 49:0e00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 
88:0000
ata3: no dma/lba
ata3: dev 0 not supported, ignoring
scsi2 : sata_nv
ata4: dev 0 cfg 49:2f00 82:74eb 83:7f63 84:4003 85:74e9 86:3c43 87:4003 
88:407f
ata4: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata4: dev 0 configured for UDMA/133
scsi3 : sata_nv
Vendor: ATA       Model: WDC WD740GD-00FL  Rev: 31.0
Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1
Attached scsi disk sdb at scsi3, channel 0, id 0, lun 0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux:  Disabled at runtime.
SELinux:  Unregistering netfilter hooks
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.32.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APCH] -> GSI 21 (level, high) 
-> IRQ 193
PCI: Setting latency timer of device 0000:00:05.0 to 64
0000:00:05.0: Invalid Mac address detected: 8d:f0:00:e7:39:00
Please complain to your hardware vendor. Switching to a random MAC.
eth0: forcedeth.c: subsystem: 01462:0250 bound to 0000:00:05.0
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [APC5] -> GSI 16 (level, low) -> 
IRQ 201
r8169: NAPI enabled
eth1: Identified chip type is 'RTL8169s/8110s'.
eth1: RTL8169 at 0xffffc20000006000, 00:11:09:8f:4f:a4, IRQ 201
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20 (level, high) 
-> IRQ 209
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49682 usecs
intel8x0: clocking to 46759
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [APC2] -> GSI 17 (level, low) -> 
IRQ 217
bttv0: Bt878 (rev 2) at 0000:02:0a.0, irq: 217, latency: 32, mmio: 
0xfdeff000
bttv0: detected: ATI TV Wonder [card=63], PCI subsystem ID is 1002:0001
bttv0: using: ATI TV-Wonder [card=63,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv0: using tuner=19
bttv0: i2c: checking for MSP34xx @ 0x80... found
msp34xx: init: chip=MSP3430G-A4 +nicam +simple +simpler +radio mode=simpler
msp34xxg: daemon started
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner 2-0060: chip found @ 0xc0 (bt878 #0 [sw])
tuner 2-0060: type set to 19 (Temic PAL* auto (4006 FN5))
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0a.1[A] -> Link [APC2] -> GSI 17 (level, low) -> 
IRQ 217
bt878(0): Bt878 (rev 2) at 02:0a.1, irq: 217, latency: 32, memory: 
0xfdefe000
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 23 (level, high) 
-> IRQ 177
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: nVidia Corporation nForce3 EHCI USB 2.0 Controller
ehci_hcd 0000:00:02.2: reset hcs_params 0x102488 dbg=1 cc=2 pcc=4 !ppc 
ports=8
ehci_hcd 0000:00:02.2: reset portroute 0 0 1 1 1 0 1 0
ehci_hcd 0000:00:02.2: reset hcc_params a082 caching frame 256/512/1024
ehci_hcd 0000:00:02.2: debug port 1
ehci_hcd 0000:00:02.2: capability 0001 at a0
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 177, io mem 0xfe02d000
ehci_hcd 0000:00:02.2: reset command 080002 (park)=0 ithresh=8 period=1024 
Reset HALT
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ehci_hcd 0000:00:02.2: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: nVidia Corporation nForce3 EHCI USB 2.0 Controller
usb usb1: Manufacturer: Linux 2.6.12.1 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0000
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, high) 
-> IRQ 185
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: nVidia Corporation CK8S USB Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 185, io mem 0xfe02f000
ohci_hcd 0000:00:02.0: resetting from state 'reset', control = 0x600
ohci_hcd 0000:00:02.0: OHCI controller state
ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.0: fminterval a7782edf
ohci_hcd 0000:00:02.0: hcca frame #0002
ohci_hcd 0000:00:02.0: roothub.a 01000204 POTPGT=1 NPS NDP=4
ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:02.0: supports USB remote wakeup
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: nVidia Corporation CK8S USB Controller
usb usb2: Manufacturer: Linux 2.6.12.1 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
ohci_hcd 0000:00:02.0: created debug files
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 21 (level, high) 
-> IRQ 193
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: nVidia Corporation CK8S USB Controller (#2)
hub 2-0:1.0: state 5 ports 4 chg 0000 evt 0000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 193, io mem 0xfe02e000
ohci_hcd 0000:00:02.1: resetting from state 'reset', control = 0x600
ohci_hcd 0000:00:02.1: OHCI controller state
ohci_hcd 0000:00:02.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.1: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:02.1: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.1: fminterval a7782edf
ohci_hcd 0000:00:02.1: hcca frame #0002
ohci_hcd 0000:00:02.1: roothub.a 01000204 POTPGT=1 NPS NDP=4
ohci_hcd 0000:00:02.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.1: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:02.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.1: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:02.1: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:02.1: supports USB remote wakeup
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: nVidia Corporation CK8S USB Controller (#2)
usb usb3: Manufacturer: Linux 2.6.12.1 ohci_hcd
usb usb3: SerialNumber: 0000:00:02.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: global over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: no over-current condition exists
ohci_hcd 0000:00:02.1: created debug files
hub 3-0:1.0: state 5 ports 4 chg 0000 evt 0000
ohci_hcd 0000:00:02.0: suspend root hub
ohci_hcd 0000:00:02.1: suspend root hub
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [APC4] -> GSI 19 (level, low) -> 
IRQ 225
PCI: Via IRQ fixup for 0000:02:0c.0, from 5 to 1
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[225]  MMIO=[fdfff000-fdfff7ff] 
  Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0010dc00007aa441]
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 0
Buffer I/O error on device hdc, logical block 0
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 4
Buffer I/O error on device hdc, logical block 1
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 8
Buffer I/O error on device hdc, logical block 2
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 12
Buffer I/O error on device hdc, logical block 3
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 16
Buffer I/O error on device hdc, logical block 4
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 20
Buffer I/O error on device hdc, logical block 5
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 24
Buffer I/O error on device hdc, logical block 6
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 28
Buffer I/O error on device hdc, logical block 7
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 32
Buffer I/O error on device hdc, logical block 8
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 36
Buffer I/O error on device hdc, logical block 9
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 40
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 44
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 48
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 52
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 56
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 60
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 0
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 4
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 795776
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 0
cdrom: open failed.
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 0
cdrom: open failed.
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.22 [Flags: R/O MODULE].
NTFS volume version 3.1.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options:  [pci] [cardbus] [pm]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80497340(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0010
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001803 POWER sig=j  CSC 
CONNECT
hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0  PE 
CONNECT
usb 1-4: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0  PE 
CONNECT
usb 1-4: default language 0x0409
usb 1-4: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: JUMPDRIVE PRO
usb 1-4: Manufacturer: LEXAR MEDIA
usb 1-4: SerialNumber: 3563BF08114025291104
usb 1-4: hotplug
usb 1-4: adding 1-4:1.0 (config #1, interface 0)
usb 1-4:1.0: hotplug
Initializing USB Mass Storage driver...
usb-storage 1-4:1.0: usb_probe_interface
usb-storage 1-4:1.0: usb_probe_interface - got id
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: LEXAR     Model: JUMPDRIVE PRO     Rev: 1000
Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sdc: 2030592 512-byte hdwr sectors (1040 MB)
sdc: Write Protect is off
sdc: Mode Sense: 43 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 2030592 512-byte hdwr sectors (1040 MB)
sdc: Write Protect is off
sdc: Mode Sense: 43 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
Attached scsi removable disk sdc at scsi4, channel 0, id 0, lun 0
usb-storage: device scan complete
hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0010
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001002 POWER sig=se0  CSC
hub 1-0:1.0: port 4, status 0100, change 0001, 12 Mb/s
usb 1-4: USB disconnect, address 2
usb 1-4: usb_disable_device nuking all URBs
usb 1-4: unregistering interface 1-4:1.0
usb 1-4:1.0: hotplug
usb 1-4: unregistering device
usb 1-4: hotplug
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100

dmesg with 3GB of RAM:
Bootdata ok (command line is ro root=LABEL=/1 rhgb 3)
Linux version 2.6.12.1 (root@localhost) (gcc version 4.0.0 20050519 (Red Hat 
4.0.0-8)) #14 SMP Tue Jul 5 00:33:42 CDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
BIOS-e820: 00000000bfff0000 - 00000000bfff3000 (ACPI NVS)
BIOS-e820: 00000000bfff3000 - 00000000c0000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 Nvidia                                ) @ 
0x00000000000f8e80
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 
0x00000000bfff3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 
0x00000000bfff30c0
ACPI: SSDT (v001 PTLTD  POWERNOW 0x00000001  LTP 0x00000001) @ 
0x00000000bfff7b80
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 
0x00000000bfff7ac0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 
0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 00000000bfff0000
Using node hash shift of 24
Bootmem setup node 0 0000000000000000-00000000bfff0000
On node 0 totalpages: 786416
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 782320 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
Nvidia board detected. Ignoring ACPI timer override.
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c0000000 (gap: c0000000:3ec00000)
Checking aperture...
CPU 0: aperture @ f0000000 size 128 MB
Built 1 zonelists
Kernel command line: ro root=LABEL=/1 rhgb 3
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 2411.002 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Memory: 3088372k/3145664k available (2382k kernel code, 0k reserved, 1584k 
data, 228k init)
Calibrating delay loop... 4767.74 BogoMIPS (lpj=2383872)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(2) -> Node 0 -> Core 0
Using local APIC timer interrupts.
Detected 12.557 MHz APIC timer.
Booting processor 1/1 rip 6000 rsp ffff810004171f58
Initializing CPU#1
Calibrating delay loop... 4816.89 BogoMIPS (lpj=2408448)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1(2) -> Node 0 -> Core 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ stepping 02
CPU 1: Syncing TSC to CPU 0.
Brought up 2 CPUs
CPU 1: synchronized TSC with CPU 0 (last diff -75 cycles, maxerr 541 cycles)
time.c: Using PIT/TSC based timekeeping.
testing NMI watchdog ... OK.
CPU0 attaching sched-domain:
domain 0: span 00000001
groups: 00000001
domain 1: span 00000003
groups: 00000001 00000002
domain 2: span 00000003
  groups: 00000003
CPU1 attaching sched-domain:
domain 0: span 00000002
groups: 00000002
domain 1: span 00000003
groups: 00000002 00000001
domain 2: span 00000003
  groups: 00000003
checking if image is initramfs... it is
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a 
report
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 128M @ 0xf0000000
PCI-DMA: Disabling IOMMU.
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4800-0x487f has been reserved
pnp: 00:00: ioport range 0x4880-0x48ff has been reserved
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1120523834.311:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
  ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:DMA
  ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y250P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: PLEXTOR DVDR PX-716A, ATAPI CD/DVD-ROM drive
hdd: TOSHIBA DVD-ROM SD-M1212, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 490234752 sectors (251000 MB) w/7936KiB Cache, CHS=30515/255/63, 
UDMA(133)
hda: cache flushes supported
hda: hda1 hda2
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 32X DVD-ROM drive, 256kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 16384 buckets, 256Kbytes
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.40.2)
powernow-k8:    0 : fid 0x10 (2400 MHz), vid 0xa (1300 mV)
powernow-k8:    1 : fid 0xe (2200 MHz), vid 0xa (1300 mV)
powernow-k8:    2 : fid 0xc (2000 MHz), vid 0xc (1250 mV)
powernow-k8:    3 : fid 0xa (1800 MHz), vid 0xe (1200 mV)
powernow-k8:    4 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0x10, vid 0xa
ACPI wakeup devices:
HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 228k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
SCSI subsystem initialized
libata version 1.11 loaded.
sata_nv version 0.6
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [APSI] -> GSI 23 (level, high) 
-> IRQ 177
PCI: Setting latency timer of device 0000:00:09.0 to 64
ata1: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC800 irq 177
ata2: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC808 irq 177
ata1: no device found (phy stat 00000000)
scsi0 : sata_nv
input: PS2++ Logitech Wheel Mouse on isa0060/serio1
ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3c01 87:4003 
88:203f
ata2: dev 0 ATA, max UDMA/100, 625142448 sectors: lba48
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata2: dev 0 configured for UDMA/100
scsi1 : sata_nv
Vendor: ATA       Model: WDC WD3200SD-01K  Rev: 08.0
Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APSJ] -> GSI 22 (level, high) 
-> IRQ 185
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ata3: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xB000 irq 185
ata4: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xB008 irq 185
ata3: dev 0 cfg 49:0e00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 
88:0000
ata3: no dma/lba
ata3: dev 0 not supported, ignoring
scsi2 : sata_nv
ata4: dev 0 cfg 49:2f00 82:74eb 83:7f63 84:4003 85:74e9 86:3c43 87:4003 
88:407f
ata4: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata4: dev 0 configured for UDMA/133
scsi3 : sata_nv
Vendor: ATA       Model: WDC WD740GD-00FL  Rev: 31.0
Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1
Attached scsi disk sdb at scsi3, channel 0, id 0, lun 0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux:  Disabled at runtime.
SELinux:  Unregistering netfilter hooks
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.32.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APCH] -> GSI 21 (level, high) 
-> IRQ 193
PCI: Setting latency timer of device 0000:00:05.0 to 64
0000:00:05.0: Invalid Mac address detected: 8d:f0:00:e7:39:00
Please complain to your hardware vendor. Switching to a random MAC.
eth0: forcedeth.c: subsystem: 01462:0250 bound to 0000:00:05.0
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [APC5] -> GSI 16 (level, low) -> 
IRQ 201
r8169: NAPI enabled
eth1: Identified chip type is 'RTL8169s/8110s'.
eth1: RTL8169 at 0xffffc20000006000, 00:11:09:8f:4f:a4, IRQ 201
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20 (level, high) 
-> IRQ 209
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49638 usecs
intel8x0: clocking to 46872
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [APC2] -> GSI 17 (level, low) -> 
IRQ 217
bttv0: Bt878 (rev 2) at 0000:02:0a.0, irq: 217, latency: 32, mmio: 
0xfdeff000
bttv0: detected: ATI TV Wonder [card=63], PCI subsystem ID is 1002:0001
bttv0: using: ATI TV-Wonder [card=63,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv0: using tuner=19
bttv0: i2c: checking for MSP34xx @ 0x80... found
msp34xx: init: chip=MSP3430G-A4 +nicam +simple +simpler +radio mode=simpler
msp34xxg: daemon started
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner 2-0060: chip found @ 0xc0 (bt878 #0 [sw])
tuner 2-0060: type set to 19 (Temic PAL* auto (4006 FN5))
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0a.1[A] -> Link [APC2] -> GSI 17 (level, low) -> 
IRQ 217
bt878(0): Bt878 (rev 2) at 02:0a.1, irq: 217, latency: 32, memory: 
0xfdefe000
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 23 (level, high) 
-> IRQ 177
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: nVidia Corporation nForce3 EHCI USB 2.0 Controller
ehci_hcd 0000:00:02.2: reset hcs_params 0x102488 dbg=1 cc=2 pcc=4 !ppc 
ports=8
ehci_hcd 0000:00:02.2: reset portroute 0 0 1 1 1 0 1 0
ehci_hcd 0000:00:02.2: reset hcc_params a082 caching frame 256/512/1024
ehci_hcd 0000:00:02.2: debug port 1
ehci_hcd 0000:00:02.2: capability 0001 at a0
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 177, io mem 0xfe02d000
ehci_hcd 0000:00:02.2: reset command 080002 (park)=0 ithresh=8 period=1024 
Reset HALT
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ehci_hcd 0000:00:02.2: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: nVidia Corporation nForce3 EHCI USB 2.0 Controller
usb usb1: Manufacturer: Linux 2.6.12.1 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0000
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, high) 
-> IRQ 185
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: nVidia Corporation CK8S USB Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 185, io mem 0xfe02f000
ohci_hcd 0000:00:02.0: resetting from state 'reset', control = 0x600
ohci_hcd 0000:00:02.0: OHCI controller state
ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.0: fminterval a7782edf
ohci_hcd 0000:00:02.0: hcca frame #0002
ohci_hcd 0000:00:02.0: roothub.a 01000204 POTPGT=1 NPS NDP=4
ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:02.0: supports USB remote wakeup
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: nVidia Corporation CK8S USB Controller
usb usb2: Manufacturer: Linux 2.6.12.1 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
ohci_hcd 0000:00:02.0: created debug files
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 21 (level, high) 
-> IRQ 193
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: nVidia Corporation CK8S USB Controller (#2)
hub 2-0:1.0: state 5 ports 4 chg 0000 evt 0000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 193, io mem 0xfe02e000
ohci_hcd 0000:00:02.1: resetting from state 'reset', control = 0x600
ohci_hcd 0000:00:02.1: OHCI controller state
ohci_hcd 0000:00:02.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.1: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:02.1: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.1: fminterval a7782edf
ohci_hcd 0000:00:02.1: hcca frame #0002
ohci_hcd 0000:00:02.1: roothub.a 01000204 POTPGT=1 NPS NDP=4
ohci_hcd 0000:00:02.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.1: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:02.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.1: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:02.1: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:02.1: supports USB remote wakeup
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: nVidia Corporation CK8S USB Controller (#2)
usb usb3: Manufacturer: Linux 2.6.12.1 ohci_hcd
usb usb3: SerialNumber: 0000:00:02.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: global over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: no over-current condition exists
ohci_hcd 0000:00:02.1: created debug files
hub 3-0:1.0: state 5 ports 4 chg 0000 evt 0000
ohci_hcd 0000:00:02.0: suspend root hub
ohci_hcd 0000:00:02.1: suspend root hub
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [APC4] -> GSI 19 (level, low) -> 
IRQ 225
PCI: Via IRQ fixup for 0000:02:0c.0, from 5 to 1
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[225]  MMIO=[fdfff000-fdfff7ff] 
  Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0010dc00007aa441]
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 0
Buffer I/O error on device hdc, logical block 0
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 4
Buffer I/O error on device hdc, logical block 1
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 8
Buffer I/O error on device hdc, logical block 2
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 12
Buffer I/O error on device hdc, logical block 3
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 16
Buffer I/O error on device hdc, logical block 4
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 20
Buffer I/O error on device hdc, logical block 5
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 24
Buffer I/O error on device hdc, logical block 6
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 28
Buffer I/O error on device hdc, logical block 7
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 32
Buffer I/O error on device hdc, logical block 8
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 36
Buffer I/O error on device hdc, logical block 9
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 40
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 44
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 48
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 52
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 56
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 60
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 0
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 4
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 795776
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 0
cdrom: open failed.
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 0
cdrom: open failed.
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.22 [Flags: R/O MODULE].
NTFS volume version 3.1.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options:  [pci] [cardbus] [pm]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80497340(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0010
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001803 POWER sig=j  CSC 
CONNECT
hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0  PE 
CONNECT
usb 1-4: new high speed USB device using ehci_hcd and address 2
usb 1-4: khubd timed out on ep0in len=0/64
usb 1-4: khubd timed out on ep0in len=0/64
usb 1-4: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0  PE 
CONNECT
usb 1-4: device descriptor read/64, error -110
usb 1-4: khubd timed out on ep0in len=0/64
usb 1-4: khubd timed out on ep0in len=0/64
usb 1-4: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0  PE 
CONNECT
usb 1-4: device descriptor read/64, error -110
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0  PE 
CONNECT
usb 1-4: new high speed USB device using ehci_hcd and address 3
usb 1-4: khubd timed out on ep0in len=0/64
usb 1-4: khubd timed out on ep0in len=0/64
usb 1-4: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0  PE 
CONNECT
usb 1-4: device descriptor read/64, error -110
usb 1-4: khubd timed out on ep0in len=0/64
usb 1-4: khubd timed out on ep0in len=0/64
usb 1-4: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0  PE 
CONNECT
usb 1-4: device descriptor read/64, error -110
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0  PE 
CONNECT
usb 1-4: new high speed USB device using ehci_hcd and address 4
usb 1-4: khubd timed out on ep0out len=0/0
usb 1-4: khubd timed out on ep0out len=0/0
usb 1-4: device not accepting address 4, error -110
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0  PE 
CONNECT
usb 1-4: new high speed USB device using ehci_hcd and address 5
usb 1-4: khubd timed out on ep0out len=0/0
usb 1-4: khubd timed out on ep0out len=0/0
usb 1-4: device not accepting address 5, error -110
hub 1-0:1.0: state 5 ports 8 chg 0000 evt 0010