* [PATCH v5 1/3] phy: add driver for Qualcomm IPQ40xx USB PHY
@ 2020-03-30 16:43 Robert Marko
2020-03-30 16:43 ` [PATCH v5 2/3] dt-bindings: phy-qcom-ipq4019-usb: add binding document Robert Marko
2020-03-30 16:43 ` [PATCH v5 3/3] ARM: dts: qcom: ipq4019: add USB devicetree nodes Robert Marko
0 siblings, 2 replies; 7+ messages in thread
From: Robert Marko @ 2020-03-30 16:43 UTC (permalink / raw)
To: agross, bjorn.andersson, kishon, linux-kernel, linux-arm-msm,
robh+dt, mark.rutland, devicetree
Cc: John Crispin, Robert Marko, Luka Perkov
From: John Crispin <john@phrozen.org>
Add a driver to setup the USB phy on Qualcom Dakota SoCs.
The driver sets up HS and SS phys.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
Changes from v2 to v3:
* Remove magic writes as they are not needed
* Correct commit message
drivers/phy/qualcomm/Kconfig | 7 +
drivers/phy/qualcomm/Makefile | 1 +
drivers/phy/qualcomm/phy-qcom-ipq4019-usb.c | 152 ++++++++++++++++++++
3 files changed, 160 insertions(+)
create mode 100644 drivers/phy/qualcomm/phy-qcom-ipq4019-usb.c
diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index e46824da29f6..964bd5d784d2 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -18,6 +18,13 @@ config PHY_QCOM_APQ8064_SATA
depends on OF
select GENERIC_PHY
+config PHY_QCOM_IPQ4019_USB
+ tristate "Qualcomm IPQ4019 USB PHY module"
+ depends on OF && ARCH_QCOM
+ select GENERIC_PHY
+ help
+ Support for the USB PHY on QCOM IPQ4019/Dakota chipsets.
+
config PHY_QCOM_IPQ806X_SATA
tristate "Qualcomm IPQ806x SATA SerDes/PHY driver"
depends on ARCH_QCOM
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index 283251d6a5d9..8afe6c4f5178 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0
obj-$(CONFIG_PHY_ATH79_USB) += phy-ath79-usb.o
obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
+obj-$(CONFIG_PHY_QCOM_IPQ4019_USB) += phy-qcom-ipq4019-usb.o
obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
obj-$(CONFIG_PHY_QCOM_PCIE2) += phy-qcom-pcie2.o
obj-$(CONFIG_PHY_QCOM_QMP) += phy-qcom-qmp.o
diff --git a/drivers/phy/qualcomm/phy-qcom-ipq4019-usb.c b/drivers/phy/qualcomm/phy-qcom-ipq4019-usb.c
new file mode 100644
index 000000000000..7efebae6b6fd
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-ipq4019-usb.c
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2018 John Crispin <john@phrozen.org>
+ *
+ * Based on code from
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+
+struct ipq4019_usb_phy {
+ struct device *dev;
+ struct phy *phy;
+ void __iomem *base;
+ struct reset_control *por_rst;
+ struct reset_control *srif_rst;
+};
+
+static int ipq4019_ss_phy_power_off(struct phy *_phy)
+{
+ struct ipq4019_usb_phy *phy = phy_get_drvdata(_phy);
+
+ reset_control_assert(phy->por_rst);
+ msleep(10);
+
+ return 0;
+}
+
+static int ipq4019_ss_phy_power_on(struct phy *_phy)
+{
+ struct ipq4019_usb_phy *phy = phy_get_drvdata(_phy);
+
+ ipq4019_ss_phy_power_off(_phy);
+
+ reset_control_deassert(phy->por_rst);
+
+ return 0;
+}
+
+static struct phy_ops ipq4019_usb_ss_phy_ops = {
+ .power_on = ipq4019_ss_phy_power_on,
+ .power_off = ipq4019_ss_phy_power_off,
+};
+
+static int ipq4019_hs_phy_power_off(struct phy *_phy)
+{
+ struct ipq4019_usb_phy *phy = phy_get_drvdata(_phy);
+
+ reset_control_assert(phy->por_rst);
+ msleep(10);
+
+ reset_control_assert(phy->srif_rst);
+ msleep(10);
+
+ return 0;
+}
+
+static int ipq4019_hs_phy_power_on(struct phy *_phy)
+{
+ struct ipq4019_usb_phy *phy = phy_get_drvdata(_phy);
+
+ ipq4019_hs_phy_power_off(_phy);
+
+ reset_control_deassert(phy->srif_rst);
+ msleep(10);
+
+ reset_control_deassert(phy->por_rst);
+
+ return 0;
+}
+
+static struct phy_ops ipq4019_usb_hs_phy_ops = {
+ .power_on = ipq4019_hs_phy_power_on,
+ .power_off = ipq4019_hs_phy_power_off,
+};
+
+static const struct of_device_id ipq4019_usb_phy_of_match[] = {
+ { .compatible = "qcom,usb-hs-ipq4019-phy", .data = &ipq4019_usb_hs_phy_ops},
+ { .compatible = "qcom,usb-ss-ipq4019-phy", .data = &ipq4019_usb_ss_phy_ops},
+ { },
+};
+MODULE_DEVICE_TABLE(of, ipq4019_usb_phy_of_match);
+
+static int ipq4019_usb_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct phy_provider *phy_provider;
+ struct ipq4019_usb_phy *phy;
+ const struct of_device_id *match;
+
+ match = of_match_device(ipq4019_usb_phy_of_match, &pdev->dev);
+ if (!match)
+ return -ENODEV;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->dev = &pdev->dev;
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ phy->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(phy->base)) {
+ dev_err(dev, "failed to remap register memory\n");
+ return PTR_ERR(phy->base);
+ }
+
+ phy->por_rst = devm_reset_control_get(phy->dev, "por_rst");
+ if (IS_ERR(phy->por_rst)) {
+ if (PTR_ERR(phy->por_rst) != -EPROBE_DEFER)
+ dev_err(dev, "POR reset is missing\n");
+ return PTR_ERR(phy->por_rst);
+ }
+
+ phy->srif_rst = devm_reset_control_get_optional(phy->dev, "srif_rst");
+ if (IS_ERR(phy->srif_rst))
+ return PTR_ERR(phy->srif_rst);
+
+ phy->phy = devm_phy_create(dev, NULL, match->data);
+ if (IS_ERR(phy->phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(phy->phy);
+ }
+ phy_set_drvdata(phy->phy, phy);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver ipq4019_usb_phy_driver = {
+ .probe = ipq4019_usb_phy_probe,
+ .driver = {
+ .of_match_table = ipq4019_usb_phy_of_match,
+ .name = "ipq4019-usb-phy",
+ }
+};
+module_platform_driver(ipq4019_usb_phy_driver);
+
+MODULE_DESCRIPTION("QCOM/IPQ4019 USB phy driver");
+MODULE_AUTHOR("John Crispin <john@phrozen.org>");
+MODULE_LICENSE("GPL v2");
--
2.26.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v5 2/3] dt-bindings: phy-qcom-ipq4019-usb: add binding document
2020-03-30 16:43 [PATCH v5 1/3] phy: add driver for Qualcomm IPQ40xx USB PHY Robert Marko
@ 2020-03-30 16:43 ` Robert Marko
2020-03-31 16:31 ` Rob Herring
2020-03-30 16:43 ` [PATCH v5 3/3] ARM: dts: qcom: ipq4019: add USB devicetree nodes Robert Marko
1 sibling, 1 reply; 7+ messages in thread
From: Robert Marko @ 2020-03-30 16:43 UTC (permalink / raw)
To: agross, bjorn.andersson, kishon, linux-kernel, linux-arm-msm,
robh+dt, mark.rutland, devicetree
Cc: Robert Marko, John Crispin, Luka Perkov
This patch adds the binding documentation for the HS/SS USB PHY found
inside Qualcom Dakota SoCs.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
Changes from v4 to v5:
* Replace tabs with whitespaces
* Add maintainer property
.../bindings/phy/qcom-usb-ipq4019-phy.yaml | 48 +++++++++++++++++++
1 file changed, 48 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml
diff --git a/Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml b/Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml
new file mode 100644
index 000000000000..4a6b5aa83925
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml
@@ -0,0 +1,48 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom-usb-ipq4019-phy.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcom IPQ40xx Dakota HS/SS USB PHY
+
+maintainers:
+ - Robert Marko <robert.marko@sartura.hr>
+
+properties:
+ compatible:
+ enum:
+ - qcom,usb-ss-ipq4019-phy
+ - qcom,usb-hs-ipq4019-phy
+
+ reg:
+ maxItems: 1
+
+ resets:
+ maxItems: 2
+
+ reset-names:
+ items:
+ - const: por_rst
+ - const: srif_rst
+
+ "#phy-cells":
+ const: 0
+
+required:
+ - compatible
+ - reg
+ - resets
+ - reset-names
+ - "#phy-cells"
+
+examples:
+ - |
+ hsphy@a8000 {
+ compatible = "qcom,usb-hs-ipq4019-phy";
+ phy-cells = <0>;
+ reg = <0xa8000 0x40>;
+ resets = <&gcc USB2_HSPHY_POR_ARES>,
+ <&gcc USB2_HSPHY_S_ARES>;
+ reset-names = "por_rst", "srif_rst";
+ };
--
2.26.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v5 3/3] ARM: dts: qcom: ipq4019: add USB devicetree nodes
2020-03-30 16:43 [PATCH v5 1/3] phy: add driver for Qualcomm IPQ40xx USB PHY Robert Marko
2020-03-30 16:43 ` [PATCH v5 2/3] dt-bindings: phy-qcom-ipq4019-usb: add binding document Robert Marko
@ 2020-03-30 16:43 ` Robert Marko
1 sibling, 0 replies; 7+ messages in thread
From: Robert Marko @ 2020-03-30 16:43 UTC (permalink / raw)
To: agross, bjorn.andersson, kishon, linux-kernel, linux-arm-msm,
robh+dt, mark.rutland, devicetree
Cc: John Crispin, Robert Marko, Luka Perkov
From: John Crispin <john@phrozen.org>
Since we now have driver for the USB PHY, lets add the necessary nodes to DTSI.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
---
arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi | 20 +++++
arch/arm/boot/dts/qcom-ipq4019.dtsi | 74 +++++++++++++++++++
2 files changed, 94 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
index 418f9a022336..2ee5f05d5a43 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
@@ -109,5 +109,25 @@ wifi@a000000 {
wifi@a800000 {
status = "ok";
};
+
+ usb3_ss_phy: ssphy@9a000 {
+ status = "ok";
+ };
+
+ usb3_hs_phy: hsphy@a6000 {
+ status = "ok";
+ };
+
+ usb3: usb3@8af8800 {
+ status = "ok";
+ };
+
+ usb2_hs_phy: hsphy@a8000 {
+ status = "ok";
+ };
+
+ usb2: usb2@60f8800 {
+ status = "ok";
+ };
};
};
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index bfa9ce4c6e69..ee45253361cb 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -576,5 +576,79 @@ wifi1: wifi@a800000 {
"legacy";
status = "disabled";
};
+
+ usb3_ss_phy: ssphy@9a000 {
+ compatible = "qcom,usb-ss-ipq4019-phy";
+ #phy-cells = <0>;
+ reg = <0x9a000 0x800>;
+ reg-names = "phy_base";
+ resets = <&gcc USB3_UNIPHY_PHY_ARES>;
+ reset-names = "por_rst";
+ status = "disabled";
+ };
+
+ usb3_hs_phy: hsphy@a6000 {
+ compatible = "qcom,usb-hs-ipq4019-phy";
+ #phy-cells = <0>;
+ reg = <0xa6000 0x40>;
+ reg-names = "phy_base";
+ resets = <&gcc USB3_HSPHY_POR_ARES>, <&gcc USB3_HSPHY_S_ARES>;
+ reset-names = "por_rst", "srif_rst";
+ status = "disabled";
+ };
+
+ usb3@8af8800 {
+ compatible = "qcom,dwc3";
+ reg = <0x8af8800 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&gcc GCC_USB3_MASTER_CLK>,
+ <&gcc GCC_USB3_SLEEP_CLK>,
+ <&gcc GCC_USB3_MOCK_UTMI_CLK>;
+ clock-names = "master", "sleep", "mock_utmi";
+ ranges;
+ status = "disabled";
+
+ dwc3@8a00000 {
+ compatible = "snps,dwc3";
+ reg = <0x8a00000 0xf8000>;
+ interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb3_hs_phy>, <&usb3_ss_phy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ dr_mode = "host";
+ };
+ };
+
+ usb2_hs_phy: hsphy@a8000 {
+ compatible = "qcom,usb-hs-ipq4019-phy";
+ #phy-cells = <0>;
+ reg = <0xa8000 0x40>;
+ reg-names = "phy_base";
+ resets = <&gcc USB2_HSPHY_POR_ARES>, <&gcc USB2_HSPHY_S_ARES>;
+ reset-names = "por_rst", "srif_rst";
+ status = "disabled";
+ };
+
+ usb2@60f8800 {
+ compatible = "qcom,dwc3";
+ reg = <0x60f8800 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&gcc GCC_USB2_MASTER_CLK>,
+ <&gcc GCC_USB2_SLEEP_CLK>,
+ <&gcc GCC_USB2_MOCK_UTMI_CLK>;
+ clock-names = "master", "sleep", "mock_utmi";
+ ranges;
+ status = "disabled";
+
+ dwc3@6000000 {
+ compatible = "snps,dwc3";
+ reg = <0x6000000 0xf8000>;
+ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2_hs_phy>;
+ phy-names = "usb2-phy";
+ dr_mode = "host";
+ };
+ };
};
};
--
2.26.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v5 2/3] dt-bindings: phy-qcom-ipq4019-usb: add binding document
2020-03-30 16:43 ` [PATCH v5 2/3] dt-bindings: phy-qcom-ipq4019-usb: add binding document Robert Marko
@ 2020-03-31 16:31 ` Rob Herring
2020-03-31 16:39 ` Robert Marko
0 siblings, 1 reply; 7+ messages in thread
From: Rob Herring @ 2020-03-31 16:31 UTC (permalink / raw)
To: Robert Marko
Cc: agross, bjorn.andersson, kishon, linux-kernel, linux-arm-msm,
robh+dt, mark.rutland, devicetree, Robert Marko, John Crispin,
Luka Perkov
On Mon, 30 Mar 2020 18:43:29 +0200, Robert Marko wrote:
> This patch adds the binding documentation for the HS/SS USB PHY found
> inside Qualcom Dakota SoCs.
>
> Signed-off-by: John Crispin <john@phrozen.org>
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Cc: Luka Perkov <luka.perkov@sartura.hr>
> ---
> Changes from v4 to v5:
> * Replace tabs with whitespaces
> * Add maintainer property
>
> .../bindings/phy/qcom-usb-ipq4019-phy.yaml | 48 +++++++++++++++++++
> 1 file changed, 48 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
Error: Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dts:21.25-26 syntax error
FATAL ERROR: Unable to parse input tree
scripts/Makefile.lib:311: recipe for target 'Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dt.yaml' failed
make[1]: *** [Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dt.yaml] Error 1
make[1]: *** Waiting for unfinished jobs....
Makefile:1262: recipe for target 'dt_binding_check' failed
make: *** [dt_binding_check] Error 2
See https://patchwork.ozlabs.org/patch/1264091
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v5 2/3] dt-bindings: phy-qcom-ipq4019-usb: add binding document
2020-03-31 16:31 ` Rob Herring
@ 2020-03-31 16:39 ` Robert Marko
2020-04-01 15:45 ` Rob Herring
0 siblings, 1 reply; 7+ messages in thread
From: Robert Marko @ 2020-03-31 16:39 UTC (permalink / raw)
To: Rob Herring
Cc: agross, Bjorn Andersson, kishon, linux-kernel, linux-arm-msm,
robh+dt, mark.rutland, devicetree, John Crispin, Luka Perkov
On Tue, Mar 31, 2020 at 6:31 PM Rob Herring <robh@kernel.org> wrote:
>
> On Mon, 30 Mar 2020 18:43:29 +0200, Robert Marko wrote:
> > This patch adds the binding documentation for the HS/SS USB PHY found
> > inside Qualcom Dakota SoCs.
> >
> > Signed-off-by: John Crispin <john@phrozen.org>
> > Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> > Cc: Luka Perkov <luka.perkov@sartura.hr>
> > ---
> > Changes from v4 to v5:
> > * Replace tabs with whitespaces
> > * Add maintainer property
> >
> > .../bindings/phy/qcom-usb-ipq4019-phy.yaml | 48 +++++++++++++++++++
> > 1 file changed, 48 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml
> >
>
> My bot found errors running 'make dt_binding_check' on your patch:
>
> Error: Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dts:21.25-26 syntax error
> FATAL ERROR: Unable to parse input tree
> scripts/Makefile.lib:311: recipe for target 'Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dt.yaml' failed
> make[1]: *** [Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dt.yaml] Error 1
> make[1]: *** Waiting for unfinished jobs....
> Makefile:1262: recipe for target 'dt_binding_check' failed
> make: *** [dt_binding_check] Error 2
>
> See https://patchwork.ozlabs.org/patch/1264091
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure dt-schema is up to date:
>
> pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
>
> Please check and re-submit.
Hi Rob,
I tested locally before submitting and it will pass.
It appears that the bot will fail in your tree as a patch to add DT
nodes is part of the series and not yet upstream.
Best regards
Robert
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v5 2/3] dt-bindings: phy-qcom-ipq4019-usb: add binding document
2020-03-31 16:39 ` Robert Marko
@ 2020-04-01 15:45 ` Rob Herring
2020-04-01 16:27 ` Robert Marko
0 siblings, 1 reply; 7+ messages in thread
From: Rob Herring @ 2020-04-01 15:45 UTC (permalink / raw)
To: Robert Marko
Cc: Andy Gross, Bjorn Andersson, Kishon Vijay Abraham I,
linux-kernel, linux-arm-msm, Mark Rutland, devicetree,
John Crispin, Luka Perkov
On Tue, Mar 31, 2020 at 10:39 AM Robert Marko <robert.marko@sartura.hr> wrote:
>
> On Tue, Mar 31, 2020 at 6:31 PM Rob Herring <robh@kernel.org> wrote:
> >
> > On Mon, 30 Mar 2020 18:43:29 +0200, Robert Marko wrote:
> > > This patch adds the binding documentation for the HS/SS USB PHY found
> > > inside Qualcom Dakota SoCs.
> > >
> > > Signed-off-by: John Crispin <john@phrozen.org>
> > > Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> > > Cc: Luka Perkov <luka.perkov@sartura.hr>
> > > ---
> > > Changes from v4 to v5:
> > > * Replace tabs with whitespaces
> > > * Add maintainer property
> > >
> > > .../bindings/phy/qcom-usb-ipq4019-phy.yaml | 48 +++++++++++++++++++
> > > 1 file changed, 48 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml
> > >
> >
> > My bot found errors running 'make dt_binding_check' on your patch:
> >
> > Error: Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dts:21.25-26 syntax error
> > FATAL ERROR: Unable to parse input tree
> > scripts/Makefile.lib:311: recipe for target 'Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dt.yaml' failed
> > make[1]: *** [Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dt.yaml] Error 1
> > make[1]: *** Waiting for unfinished jobs....
> > Makefile:1262: recipe for target 'dt_binding_check' failed
> > make: *** [dt_binding_check] Error 2
> >
> > See https://patchwork.ozlabs.org/patch/1264091
> >
> > If you already ran 'make dt_binding_check' and didn't see the above
> > error(s), then make sure dt-schema is up to date:
> >
> > pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
> >
> > Please check and re-submit.
> Hi Rob,
> I tested locally before submitting and it will pass.
Impossible. Your example has defines, but there are no include files listed.
Rob
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v5 2/3] dt-bindings: phy-qcom-ipq4019-usb: add binding document
2020-04-01 15:45 ` Rob Herring
@ 2020-04-01 16:27 ` Robert Marko
0 siblings, 0 replies; 7+ messages in thread
From: Robert Marko @ 2020-04-01 16:27 UTC (permalink / raw)
To: Rob Herring
Cc: Andy Gross, Bjorn Andersson, Kishon Vijay Abraham I,
linux-kernel, linux-arm-msm, Mark Rutland, devicetree,
John Crispin, Luka Perkov
On Wed, Apr 1, 2020 at 5:45 PM Rob Herring <robh@kernel.org> wrote:
>
> On Tue, Mar 31, 2020 at 10:39 AM Robert Marko <robert.marko@sartura.hr> wrote:
> >
> > On Tue, Mar 31, 2020 at 6:31 PM Rob Herring <robh@kernel.org> wrote:
> > >
> > > On Mon, 30 Mar 2020 18:43:29 +0200, Robert Marko wrote:
> > > > This patch adds the binding documentation for the HS/SS USB PHY found
> > > > inside Qualcom Dakota SoCs.
> > > >
> > > > Signed-off-by: John Crispin <john@phrozen.org>
> > > > Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> > > > Cc: Luka Perkov <luka.perkov@sartura.hr>
> > > > ---
> > > > Changes from v4 to v5:
> > > > * Replace tabs with whitespaces
> > > > * Add maintainer property
> > > >
> > > > .../bindings/phy/qcom-usb-ipq4019-phy.yaml | 48 +++++++++++++++++++
> > > > 1 file changed, 48 insertions(+)
> > > > create mode 100644 Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml
> > > >
> > >
> > > My bot found errors running 'make dt_binding_check' on your patch:
> > >
> > > Error: Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dts:21.25-26 syntax error
> > > FATAL ERROR: Unable to parse input tree
> > > scripts/Makefile.lib:311: recipe for target 'Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dt.yaml' failed
> > > make[1]: *** [Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.example.dt.yaml] Error 1
> > > make[1]: *** Waiting for unfinished jobs....
> > > Makefile:1262: recipe for target 'dt_binding_check' failed
> > > make: *** [dt_binding_check] Error 2
> > >
> > > See https://patchwork.ozlabs.org/patch/1264091
> > >
> > > If you already ran 'make dt_binding_check' and didn't see the above
> > > error(s), then make sure dt-schema is up to date:
> > >
> > > pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
> > >
> > > Please check and re-submit.
> > Hi Rob,
> > I tested locally before submitting and it will pass.
>
> Impossible. Your example has defines, but there are no include files listed.
I don't know how it passed, but I definitively tested with make
dtbs_check and then make dt_binding_check
It could possibly be old DT schema files, I updated today and now it pops up.
I will fix it and send a new version ASAP.
Thanks
>
> Rob
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2020-04-01 16:27 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-30 16:43 [PATCH v5 1/3] phy: add driver for Qualcomm IPQ40xx USB PHY Robert Marko
2020-03-30 16:43 ` [PATCH v5 2/3] dt-bindings: phy-qcom-ipq4019-usb: add binding document Robert Marko
2020-03-31 16:31 ` Rob Herring
2020-03-31 16:39 ` Robert Marko
2020-04-01 15:45 ` Rob Herring
2020-04-01 16:27 ` Robert Marko
2020-03-30 16:43 ` [PATCH v5 3/3] ARM: dts: qcom: ipq4019: add USB devicetree nodes Robert Marko
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).