From: "Václav Kubernát" <kubernat@cesnet.cz>
To: Jean Delvare <jdelvare@suse.com>,
Guenter Roeck <linux@roeck-us.net>,
Jonathan Corbet <corbet@lwn.net>,
linux-hwmon@vger.kernel.org, linux-doc@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v5 2/5] hwmon: (max31790) Fix and split pwm*_enable
Date: Wed, 12 May 2021 03:32:36 +0200 [thread overview]
Message-ID: <CABKa3noSQVtAp3Ath9=PNh2cDLgq8n8w2gudwWJerD5YQx5WMA@mail.gmail.com> (raw)
In-Reply-To: <20210512013052.903297-2-kubernat@cesnet.cz>
Hello,
I have updated the code and got rid of the "fullspeed" mode as
requested. Let me know what you think.
Thanks
Václav
st 12. 5. 2021 v 3:31 odesílatel Václav Kubernát <kubernat@cesnet.cz> napsal:
>
> In the old code, pwm*_enable does two things. Firstly, it sets whether
> the chip should run in PWM or RPM mode. Secondly, it tells the chip
> whether it should monitor fan RPM. However, these two settings aren't
> tied together, so they shouldn't be set with a single value. In the new
> code, fan*_enable now controls fan RPM monitoring (pwm*_enable no longer
> controls that).
>
> According to the sysfs hwmon documentation, pwm*_enable has three
> possible values, 0 for "no control / full-speed", 1 for manual mode, and
> 2+ for automatic. The old code works fine for 1 and 2, but 0 only
> differs from 1 in that it just turns off fan speed monitoring. The chip
> actually does have a way to turn off fan controls (and only monitor),
> and what that does is that it sets PWM to 0% duty cycle. In the new
> code, 0 in pwm*_enable turns off the "control" feature of the chip.
>
> These two changes are closely connected together, mainly because the
> detection of the pwm*_enable value depended on whether fan speed
> monitoring is enabled (which is now controlled as written in the first
> paragraph).
>
> Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
> ---
> Documentation/hwmon/max31790.rst | 10 ++--
> drivers/hwmon/max31790.c | 78 +++++++++++++++++++++-----------
> 2 files changed, 58 insertions(+), 30 deletions(-)
>
> diff --git a/Documentation/hwmon/max31790.rst b/Documentation/hwmon/max31790.rst
> index f301385d8cef..d2ac4e926905 100644
> --- a/Documentation/hwmon/max31790.rst
> +++ b/Documentation/hwmon/max31790.rst
> @@ -34,10 +34,14 @@ also be configured to serve as tachometer inputs.
> Sysfs entries
> -------------
>
> -================== === =======================================================
> +================== === =============================================================
> +fan[1-12]_enable RW enable fan speed monitoring
> fan[1-12]_input RO fan tachometer speed in RPM
> fan[1-12]_fault RO fan experienced fault
> fan[1-6]_target RW desired fan speed in RPM
> -pwm[1-6]_enable RW regulator mode, 0=disabled, 1=manual mode, 2=rpm mode
> +pwm[1-6]_enable RW regulator mode, 0=no control, sets 0% PWM,
> + 1=manual (pwm) mode,
> + 2=rpm mode
> + setting rpm mode sets fan*_enable to 1
> pwm[1-6] RW fan target duty cycle (0-255)
> -================== === =======================================================
> +================== === =============================================================
> diff --git a/drivers/hwmon/max31790.c b/drivers/hwmon/max31790.c
> index e3765ce4444a..5d4c551df010 100644
> --- a/drivers/hwmon/max31790.c
> +++ b/drivers/hwmon/max31790.c
> @@ -30,6 +30,7 @@
> #define MAX31790_FAN_CFG_RPM_MODE 0x80
> #define MAX31790_FAN_CFG_TACH_INPUT_EN 0x08
> #define MAX31790_FAN_CFG_TACH_INPUT 0x01
> +#define MAX31790_FAN_CFG_CTRL_MON 0x10
>
> /* Fan Dynamics register bits */
> #define MAX31790_FAN_DYN_SR_SHIFT 5
> @@ -191,6 +192,9 @@ static int max31790_read_fan(struct device *dev, u32 attr, int channel,
> else
> *val = !!(fault & (1 << channel));
> return 0;
> + case hwmon_fan_enable:
> + *val = !!(data->fan_config[channel] & MAX31790_FAN_CFG_TACH_INPUT_EN);
> + return 0;
> default:
> return -EOPNOTSUPP;
> }
> @@ -233,6 +237,15 @@ static int max31790_write_fan(struct device *dev, u32 attr, int channel,
> MAX31790_REG_TARGET_COUNT(channel),
> target_count);
> break;
> + case hwmon_fan_enable:
> + if (val == 0)
> + data->fan_config[channel] &= ~MAX31790_FAN_CFG_TACH_INPUT_EN;
> + else
> + data->fan_config[channel] |= MAX31790_FAN_CFG_TACH_INPUT_EN;
> + err = regmap_write(regmap,
> + MAX31790_REG_FAN_CONFIG(channel),
> + data->fan_config[channel]);
> + break;
> default:
> err = -EOPNOTSUPP;
> break;
> @@ -260,6 +273,11 @@ static umode_t max31790_fan_is_visible(const void *_data, u32 attr, int channel)
> !(fan_config & MAX31790_FAN_CFG_TACH_INPUT))
> return 0644;
> return 0;
> + case hwmon_fan_enable:
> + if (channel < NR_CHANNEL ||
> + (fan_config & MAX31790_FAN_CFG_TACH_INPUT))
> + return 0644;
> + return 0;
> default:
> return 0;
> }
> @@ -281,12 +299,12 @@ static int max31790_read_pwm(struct device *dev, u32 attr, int channel,
> *val = read >> 8;
> return 0;
> case hwmon_pwm_enable:
> - if (data->fan_config[channel] & MAX31790_FAN_CFG_RPM_MODE)
> + if (data->fan_config[channel] & MAX31790_FAN_CFG_CTRL_MON)
> + *val = 0;
> + else if (data->fan_config[channel] & MAX31790_FAN_CFG_RPM_MODE)
> *val = 2;
> - else if (data->fan_config[channel] & MAX31790_FAN_CFG_TACH_INPUT_EN)
> + else
> *val = 1;
> - else
> - *val = 0;
> return 0;
> default:
> return -EOPNOTSUPP;
> @@ -298,35 +316,41 @@ static int max31790_write_pwm(struct device *dev, u32 attr, int channel,
> {
> struct max31790_data *data = dev_get_drvdata(dev);
> struct regmap *regmap = data->regmap;
> - u8 fan_config;
> + u8 fan_config = data->fan_config[channel];
> int err = 0;
>
> mutex_lock(&data->update_lock);
>
> switch (attr) {
> case hwmon_pwm_input:
> - if (val < 0 || val > 255) {
> + if (fan_config & MAX31790_FAN_CFG_CTRL_MON || val < 0 || val > 255) {
> err = -EINVAL;
> break;
> }
> +
> err = write_reg_word(regmap, MAX31790_REG_PWMOUT(channel), val << 8);
> break;
> case hwmon_pwm_enable:
> fan_config = data->fan_config[channel];
> - if (val == 0) {
> - fan_config &= ~(MAX31790_FAN_CFG_TACH_INPUT_EN |
> - MAX31790_FAN_CFG_RPM_MODE);
> - } else if (val == 1) {
> - fan_config = (fan_config |
> - MAX31790_FAN_CFG_TACH_INPUT_EN) &
> - ~MAX31790_FAN_CFG_RPM_MODE;
> + if (val == 0)
> + fan_config |= MAX31790_FAN_CFG_CTRL_MON;
> + else if (val == 1) {
> + fan_config &= ~(MAX31790_FAN_CFG_RPM_MODE | MAX31790_FAN_CFG_CTRL_MON);
> } else if (val == 2) {
> - fan_config |= MAX31790_FAN_CFG_TACH_INPUT_EN |
> - MAX31790_FAN_CFG_RPM_MODE;
> + fan_config &= ~(MAX31790_FAN_CFG_CTRL_MON);
> + fan_config |= MAX31790_FAN_CFG_RPM_MODE;
> } else {
> err = -EINVAL;
> break;
> }
> +
> + /*
> + * RPM mode implies enabled TACH input, so enable it in RPM
> + * mode.
> + */
> + if (val == 2)
> + fan_config |= MAX31790_FAN_CFG_TACH_INPUT_EN;
> +
> data->fan_config[channel] = fan_config;
> err = regmap_write(regmap,
> MAX31790_REG_FAN_CONFIG(channel),
> @@ -400,18 +424,18 @@ static umode_t max31790_is_visible(const void *data,
>
> static const struct hwmon_channel_info *max31790_info[] = {
> HWMON_CHANNEL_INFO(fan,
> - HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_FAULT,
> - HWMON_F_INPUT | HWMON_F_FAULT),
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_TARGET | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_FAULT,
> + HWMON_F_ENABLE | HWMON_F_INPUT | HWMON_F_FAULT),
> HWMON_CHANNEL_INFO(pwm,
> HWMON_PWM_INPUT | HWMON_PWM_ENABLE,
> HWMON_PWM_INPUT | HWMON_PWM_ENABLE,
> --
> 2.31.1
>
next prev parent reply other threads:[~2021-05-12 1:33 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-12 1:30 [PATCH v5 1/5] hwmon: (max31790) Rework to use regmap Václav Kubernát
2021-05-12 1:30 ` [PATCH v5 2/5] hwmon: (max31790) Fix and split pwm*_enable Václav Kubernát
2021-05-12 1:32 ` Václav Kubernát [this message]
2021-05-18 14:59 ` Guenter Roeck
2021-05-19 23:11 ` Guenter Roeck
2021-05-12 1:30 ` [PATCH v5 3/5] hwmon: (max31790) Show 0 RPM/fault when input disabled Václav Kubernát
2021-05-12 1:30 ` [PATCH v5 4/5] hwmon: (max31790) Allow setting fan*_div Václav Kubernát
2021-05-12 1:30 ` [PATCH v5 5/5] hwmon: (max31790) Update documentation Václav Kubernát
2021-05-19 19:00 ` [PATCH v5 1/5] hwmon: (max31790) Rework to use regmap Guenter Roeck
2021-05-20 5:12 ` Guenter Roeck
2021-05-18 21:16 [PATCH v5 2/5] hwmon: (max31790) Fix and split pwm*_enable Guenter Roeck
2021-05-19 9:10 ` Jan Kundrát
2021-05-19 13:55 ` Guenter Roeck
2021-05-20 11:29 ` Jan Kundrát
2021-05-20 11:50 ` Guenter Roeck
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CABKa3noSQVtAp3Ath9=PNh2cDLgq8n8w2gudwWJerD5YQx5WMA@mail.gmail.com' \
--to=kubernat@cesnet.cz \
--cc=corbet@lwn.net \
--cc=jdelvare@suse.com \
--cc=linux-doc@vger.kernel.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@roeck-us.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).