* [PATCH v3 5/5] Clk: RK808: Add clkout driver for RK808
@ 2014-08-23 11:07 Chris Zhong
2014-08-25 4:04 ` Doug Anderson
0 siblings, 1 reply; 3+ messages in thread
From: Chris Zhong @ 2014-08-23 11:07 UTC (permalink / raw)
To: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, sameo,
lee.jones, lgirdwood, broonie, a.zummo, mturquette
Cc: devicetree, linux-kernel, rtc-linux, grant.likely, hl, huangtao,
cf, zhangqing, xxx, dianders, heiko, olof, sonnyrao, dtor,
javier.martinez, kever.yang, Chris Zhong
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
---
Changes in v4:
Advices by Doug
- add a "#clock-cells" propertiy
- update the example
Changes in v3: None
Changes in v2: None
drivers/clk/Kconfig | 9 ++
drivers/clk/Makefile | 1 +
drivers/clk/clk-rk808.c | 162 ++++++++++++++++++++++++++++
include/dt-bindings/clock/rockchip,rk808.h | 11 ++
4 files changed, 183 insertions(+)
create mode 100644 drivers/clk/clk-rk808.c
create mode 100644 include/dt-bindings/clock/rockchip,rk808.h
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index cfd3af7..84e0590 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -38,6 +38,15 @@ config COMMON_CLK_MAX77686
---help---
This driver supports Maxim 77686 crystal oscillator clock.
+config COMMON_CLK_RK808
+ tristate "Clock driver for RK808"
+ depends on MFD_RK808
+ ---help---
+ This driver supports RK808 crystal oscillator clock. These
+ multi-function devices have two fixed-rate oscillators,
+ clocked at 32KHz each. Clkout1 is always on, Clkout2 can off
+ by control register.
+
config COMMON_CLK_SI5351
tristate "Clock driver for SiLabs 5351A/B/C"
depends on I2C
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index f537a0b..99f53d5 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_ARCH_NOMADIK) += clk-nomadik.o
obj-$(CONFIG_ARCH_NSPIRE) += clk-nspire.o
obj-$(CONFIG_COMMON_CLK_PALMAS) += clk-palmas.o
obj-$(CONFIG_CLK_PPC_CORENET) += clk-ppc-corenet.o
+obj-$(CONFIG_COMMON_CLK_RK808) += clk-rk808.o
obj-$(CONFIG_COMMON_CLK_S2MPS11) += clk-s2mps11.o
obj-$(CONFIG_COMMON_CLK_SI5351) += clk-si5351.o
obj-$(CONFIG_COMMON_CLK_SI570) += clk-si570.o
diff --git a/drivers/clk/clk-rk808.c b/drivers/clk/clk-rk808.c
new file mode 100644
index 0000000..50a25fc
--- /dev/null
+++ b/drivers/clk/clk-rk808.c
@@ -0,0 +1,162 @@
+/*
+ * Clkout driver for Rockchip RK808
+ *
+ * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * Author: Chris Zhong <zyw@rock-chips.com>
+ * Author: Zhang Qing <zhangqing@rock-chips.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/rk808.h>
+#include <linux/i2c.h>
+
+struct rk808_clkout {
+ struct rk808 *rk808;
+ struct clk_onecell_data clk_data;
+ struct clk_hw clkout1_hw;
+ struct clk_hw clkout2_hw;
+};
+
+static unsigned long rk808_clkout_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return 32768;
+}
+
+static int rk808_clkout1_is_prepared(struct clk_hw *hw)
+{
+ return 1;
+}
+
+static int rk808_clkout2_control(struct clk_hw *hw, bool enable)
+{
+ struct rk808_clkout *rk808_clkout = container_of(hw,
+ struct rk808_clkout,
+ clkout2_hw);
+ struct rk808 *rk808 = rk808_clkout->rk808;
+
+ return regmap_update_bits(rk808->regmap, RK808_CLK32OUT_REG,
+ CLK32KOUT2_EN, enable ? CLK32KOUT2_EN : 0);
+}
+
+static int rk808_clkout2_prepare(struct clk_hw *hw)
+{
+ return rk808_clkout2_control(hw, 1);
+}
+
+static void rk808_clkout2_unprepare(struct clk_hw *hw)
+{
+ rk808_clkout2_control(hw, 0);
+}
+
+static int rk808_clkout2_is_prepared(struct clk_hw *hw)
+{
+ struct rk808_clkout *rk808_clkout = container_of(hw,
+ struct rk808_clkout,
+ clkout2_hw);
+ struct rk808 *rk808 = rk808_clkout->rk808;
+ uint32_t val;
+
+ int ret = regmap_read(rk808->regmap, RK808_CLK32OUT_REG, &val);
+
+ if (ret < 0)
+ return ret;
+
+ return (val & CLK32KOUT2_EN) ? 1 : 0;
+}
+
+static const struct clk_ops rk808_clkout1_ops = {
+ .is_prepared = rk808_clkout1_is_prepared,
+ .recalc_rate = rk808_clkout_recalc_rate,
+};
+
+static const struct clk_ops rk808_clkout2_ops = {
+ .prepare = rk808_clkout2_prepare,
+ .unprepare = rk808_clkout2_unprepare,
+ .is_prepared = rk808_clkout2_is_prepared,
+ .recalc_rate = rk808_clkout_recalc_rate,
+};
+
+static int rk808_clkout_probe(struct platform_device *pdev)
+{
+ struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
+ struct i2c_client *client = rk808->i2c;
+ struct device_node *node = client->dev.of_node;
+ struct clk_init_data init;
+ struct clk **clk_table;
+ struct rk808_clkout *rk808_clkout;
+
+ rk808_clkout = devm_kzalloc(&client->dev,
+ sizeof(*rk808_clkout), GFP_KERNEL);
+ if (!rk808_clkout)
+ return -ENOMEM;
+
+ rk808_clkout->rk808 = rk808;
+
+ clk_table = devm_kzalloc(&client->dev,
+ 2*sizeof(struct clk *), GFP_KERNEL);
+ if (!clk_table)
+ return -ENOMEM;
+
+ init.flags = CLK_IS_ROOT;
+ init.parent_names = NULL;
+ init.num_parents = 0;
+ init.name = "rk808-clkout1";
+ init.ops = &rk808_clkout1_ops;
+ rk808_clkout->clkout1_hw.init = &init;
+
+ /* optional override of the clockname */
+ of_property_read_string_index(node, "clock-output-names",
+ 0, &init.name);
+
+ clk_table[0] = devm_clk_register(&client->dev,
+ &rk808_clkout->clkout1_hw);
+
+ init.name = "rk808-clkout2";
+ init.ops = &rk808_clkout2_ops;
+ rk808_clkout->clkout2_hw.init = &init;
+
+ /* optional override of the clockname */
+ of_property_read_string_index(node, "clock-output-names",
+ 1, &init.name);
+
+ clk_table[1] = devm_clk_register(&client->dev,
+ &rk808_clkout->clkout2_hw);
+
+ rk808_clkout->clk_data.clks = clk_table;
+ rk808_clkout->clk_data.clk_num = 2;
+ of_clk_add_provider(node, of_clk_src_onecell_get, clk_table);
+
+ return 0;
+}
+
+static struct platform_driver rk808_clkout_driver = {
+ .probe = rk808_clkout_probe,
+ .driver = {
+ .name = "rk808-clkout",
+ .owner = THIS_MODULE,
+ },
+};
+
+module_platform_driver(rk808_clkout_driver);
+
+MODULE_DESCRIPTION("Clkout driver for the rk808 series PMICs");
+MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
+MODULE_AUTHOR("Zhang Qing <zhanqging@rock-chips.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:rk808-clkout");
diff --git a/include/dt-bindings/clock/rockchip,rk808.h b/include/dt-bindings/clock/rockchip,rk808.h
new file mode 100644
index 0000000..1a87343
--- /dev/null
+++ b/include/dt-bindings/clock/rockchip,rk808.h
@@ -0,0 +1,11 @@
+/*
+ * This header provides constants clk index RK808 pmic clkout
+ */
+#ifndef _CLK_ROCKCHIP_RK808
+#define _CLK_ROCKCHIP_RK808
+
+/* CLOCKOUT index */
+#define RK808_CLKOUT0 0
+#define RK808_CLKOUT1 1
+
+#endif
--
1.7.9.5
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v3 5/5] Clk: RK808: Add clkout driver for RK808
2014-08-23 11:07 [PATCH v3 5/5] Clk: RK808: Add clkout driver for RK808 Chris Zhong
@ 2014-08-25 4:04 ` Doug Anderson
0 siblings, 0 replies; 3+ messages in thread
From: Doug Anderson @ 2014-08-25 4:04 UTC (permalink / raw)
To: Chris Zhong
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Samuel Ortiz, Lee Jones, Liam Girdwood, broonie,
Alessandro Zummo, Mike Turquette, devicetree, linux-kernel,
rtc-linux, Grant Likely, Lin Huang, Tao Huang, Eddie Cai,
zhangqing, xxx, Heiko Stübner, Olof Johansson, Sonny Rao,
Dmitry Torokhov, Javier Martinez Canillas, Kever Yang
Chris,
On Sat, Aug 23, 2014 at 4:07 AM, Chris Zhong <zyw@rock-chips.com> wrote:
> Signed-off-by: Chris Zhong <zyw@rock-chips.com>
>
> ---
>
> Changes in v4:
Wait, is this v4 or v3? The subject line still says v3, which is confusing.
> Advices by Doug
> - add a "#clock-cells" propertiy
> - update the example
>
> Changes in v3: None
> Changes in v2: None
>
> drivers/clk/Kconfig | 9 ++
> drivers/clk/Makefile | 1 +
> drivers/clk/clk-rk808.c | 162 ++++++++++++++++++++++++++++
> include/dt-bindings/clock/rockchip,rk808.h | 11 ++
> 4 files changed, 183 insertions(+)
> create mode 100644 drivers/clk/clk-rk808.c
> create mode 100644 include/dt-bindings/clock/rockchip,rk808.h
>
> diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
> index cfd3af7..84e0590 100644
> --- a/drivers/clk/Kconfig
> +++ b/drivers/clk/Kconfig
> @@ -38,6 +38,15 @@ config COMMON_CLK_MAX77686
> ---help---
> This driver supports Maxim 77686 crystal oscillator clock.
>
> +config COMMON_CLK_RK808
> + tristate "Clock driver for RK808"
> + depends on MFD_RK808
> + ---help---
> + This driver supports RK808 crystal oscillator clock. These
> + multi-function devices have two fixed-rate oscillators,
> + clocked at 32KHz each. Clkout1 is always on, Clkout2 can off
> + by control register.
> +
> config COMMON_CLK_SI5351
> tristate "Clock driver for SiLabs 5351A/B/C"
> depends on I2C
> diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
> index f537a0b..99f53d5 100644
> --- a/drivers/clk/Makefile
> +++ b/drivers/clk/Makefile
> @@ -28,6 +28,7 @@ obj-$(CONFIG_ARCH_NOMADIK) += clk-nomadik.o
> obj-$(CONFIG_ARCH_NSPIRE) += clk-nspire.o
> obj-$(CONFIG_COMMON_CLK_PALMAS) += clk-palmas.o
> obj-$(CONFIG_CLK_PPC_CORENET) += clk-ppc-corenet.o
> +obj-$(CONFIG_COMMON_CLK_RK808) += clk-rk808.o
> obj-$(CONFIG_COMMON_CLK_S2MPS11) += clk-s2mps11.o
> obj-$(CONFIG_COMMON_CLK_SI5351) += clk-si5351.o
> obj-$(CONFIG_COMMON_CLK_SI570) += clk-si570.o
> diff --git a/drivers/clk/clk-rk808.c b/drivers/clk/clk-rk808.c
> new file mode 100644
> index 0000000..50a25fc
> --- /dev/null
> +++ b/drivers/clk/clk-rk808.c
> @@ -0,0 +1,162 @@
> +/*
> + * Clkout driver for Rockchip RK808
> + *
> + * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
> + *
> + * Author: Chris Zhong <zyw@rock-chips.com>
> + * Author: Zhang Qing <zhangqing@rock-chips.com>
You have author below. Why is it here, too?
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> + *
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/module.h>
> +#include <linux/slab.h>
> +#include <linux/platform_device.h>
> +#include <linux/mfd/rk808.h>
> +#include <linux/i2c.h>
> +
> +struct rk808_clkout {
> + struct rk808 *rk808;
> + struct clk_onecell_data clk_data;
> + struct clk_hw clkout1_hw;
> + struct clk_hw clkout2_hw;
> +};
> +
> +static unsigned long rk808_clkout_recalc_rate(struct clk_hw *hw,
> + unsigned long parent_rate)
> +{
> + return 32768;
> +}
> +
> +static int rk808_clkout1_is_prepared(struct clk_hw *hw)
> +{
> + return 1;
> +}
> +
> +static int rk808_clkout2_control(struct clk_hw *hw, bool enable)
> +{
> + struct rk808_clkout *rk808_clkout = container_of(hw,
> + struct rk808_clkout,
> + clkout2_hw);
> + struct rk808 *rk808 = rk808_clkout->rk808;
> +
> + return regmap_update_bits(rk808->regmap, RK808_CLK32OUT_REG,
> + CLK32KOUT2_EN, enable ? CLK32KOUT2_EN : 0);
> +}
> +
> +static int rk808_clkout2_prepare(struct clk_hw *hw)
> +{
> + return rk808_clkout2_control(hw, 1);
> +}
> +
> +static void rk808_clkout2_unprepare(struct clk_hw *hw)
> +{
> + rk808_clkout2_control(hw, 0);
> +}
> +
> +static int rk808_clkout2_is_prepared(struct clk_hw *hw)
> +{
> + struct rk808_clkout *rk808_clkout = container_of(hw,
> + struct rk808_clkout,
> + clkout2_hw);
> + struct rk808 *rk808 = rk808_clkout->rk808;
> + uint32_t val;
> +
> + int ret = regmap_read(rk808->regmap, RK808_CLK32OUT_REG, &val);
> +
> + if (ret < 0)
> + return ret;
> +
> + return (val & CLK32KOUT2_EN) ? 1 : 0;
> +}
> +
> +static const struct clk_ops rk808_clkout1_ops = {
> + .is_prepared = rk808_clkout1_is_prepared,
> + .recalc_rate = rk808_clkout_recalc_rate,
> +};
> +
> +static const struct clk_ops rk808_clkout2_ops = {
> + .prepare = rk808_clkout2_prepare,
> + .unprepare = rk808_clkout2_unprepare,
> + .is_prepared = rk808_clkout2_is_prepared,
> + .recalc_rate = rk808_clkout_recalc_rate,
> +};
> +
> +static int rk808_clkout_probe(struct platform_device *pdev)
> +{
> + struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
> + struct i2c_client *client = rk808->i2c;
> + struct device_node *node = client->dev.of_node;
> + struct clk_init_data init;
Seems safer to have "= {};" here. Looks like you're initting
everything, but still...
> + struct clk **clk_table;
> + struct rk808_clkout *rk808_clkout;
> +
> + rk808_clkout = devm_kzalloc(&client->dev,
> + sizeof(*rk808_clkout), GFP_KERNEL);
> + if (!rk808_clkout)
> + return -ENOMEM;
> +
> + rk808_clkout->rk808 = rk808;
> +
> + clk_table = devm_kzalloc(&client->dev,
> + 2*sizeof(struct clk *), GFP_KERNEL);
> + if (!clk_table)
> + return -ENOMEM;
> +
> + init.flags = CLK_IS_ROOT;
> + init.parent_names = NULL;
> + init.num_parents = 0;
> + init.name = "rk808-clkout1";
> + init.ops = &rk808_clkout1_ops;
> + rk808_clkout->clkout1_hw.init = &init;
> +
> + /* optional override of the clockname */
> + of_property_read_string_index(node, "clock-output-names",
> + 0, &init.name);
> +
> + clk_table[0] = devm_clk_register(&client->dev,
> + &rk808_clkout->clkout1_hw);
Check for error value here?
> +
> + init.name = "rk808-clkout2";
> + init.ops = &rk808_clkout2_ops;
> + rk808_clkout->clkout2_hw.init = &init;
> +
> + /* optional override of the clockname */
> + of_property_read_string_index(node, "clock-output-names",
> + 1, &init.name);
> +
> + clk_table[1] = devm_clk_register(&client->dev,
> + &rk808_clkout->clkout2_hw);
Check for error here?
> +
> + rk808_clkout->clk_data.clks = clk_table;
> + rk808_clkout->clk_data.clk_num = 2;
> + of_clk_add_provider(node, of_clk_src_onecell_get, clk_table);
Return the result of of_clk_add_provider() since it returns an error.
> +
> + return 0;
> +}
> +
> +static struct platform_driver rk808_clkout_driver = {
> + .probe = rk808_clkout_probe,
> + .driver = {
> + .name = "rk808-clkout",
> + .owner = THIS_MODULE,
> + },
> +};
> +
> +module_platform_driver(rk808_clkout_driver);
I have this feeling that we're going to want this to be
subsys_initcall() because it's such a core component and that will
mean the MFD will need to be subsys_initcall() and that will mean that
the i2c needs to be subsys_initcall(). ...but then everyone will yell
that everything in the system is supposed to be module-level. ...so I
guess we'll just leave it as module_platform_driver() for now...
> +MODULE_DESCRIPTION("Clkout driver for the rk808 series PMICs");
> +MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
> +MODULE_AUTHOR("Zhang Qing <zhanqging@rock-chips.com>");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:rk808-clkout");
> diff --git a/include/dt-bindings/clock/rockchip,rk808.h b/include/dt-bindings/clock/rockchip,rk808.h
The "include/dt-bindings/clock/rockchip,rk808.h" file belongs in the
first patch. It's part of the dt-bindings...
> new file mode 100644
> index 0000000..1a87343
> --- /dev/null
> +++ b/include/dt-bindings/clock/rockchip,rk808.h
> @@ -0,0 +1,11 @@
> +/*
> + * This header provides constants clk index RK808 pmic clkout
> + */
> +#ifndef _CLK_ROCKCHIP_RK808
> +#define _CLK_ROCKCHIP_RK808
> +
> +/* CLOCKOUT index */
> +#define RK808_CLKOUT0 0
> +#define RK808_CLKOUT1 1
> +
> +#endif
> --
> 1.7.9.5
>
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH v3 5/5] Clk: RK808: Add clkout driver for RK808
@ 2014-08-21 13:37 Chris Zhong
0 siblings, 0 replies; 3+ messages in thread
From: Chris Zhong @ 2014-08-21 13:37 UTC (permalink / raw)
To: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, sameo,
lee.jones, lgirdwood, broonie, a.zummo, mturquette
Cc: devicetree, linux-kernel, rtc-linux, grant.likely, hl, huangtao,
cf, zhangqing, xxx, dianders, heiko, olof, sonnyrao, dtor,
javier.martinez, kever.yang, Chris Zhong
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
---
Changes in v3: None
Changes in v2: None
drivers/clk/Kconfig | 9 +++
drivers/clk/Makefile | 1 +
drivers/clk/clk-rk808.c | 147 +++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 157 insertions(+)
create mode 100644 drivers/clk/clk-rk808.c
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index cfd3af7..84e0590 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -38,6 +38,15 @@ config COMMON_CLK_MAX77686
---help---
This driver supports Maxim 77686 crystal oscillator clock.
+config COMMON_CLK_RK808
+ tristate "Clock driver for RK808"
+ depends on MFD_RK808
+ ---help---
+ This driver supports RK808 crystal oscillator clock. These
+ multi-function devices have two fixed-rate oscillators,
+ clocked at 32KHz each. Clkout1 is always on, Clkout2 can off
+ by control register.
+
config COMMON_CLK_SI5351
tristate "Clock driver for SiLabs 5351A/B/C"
depends on I2C
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index f537a0b..99f53d5 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_ARCH_NOMADIK) += clk-nomadik.o
obj-$(CONFIG_ARCH_NSPIRE) += clk-nspire.o
obj-$(CONFIG_COMMON_CLK_PALMAS) += clk-palmas.o
obj-$(CONFIG_CLK_PPC_CORENET) += clk-ppc-corenet.o
+obj-$(CONFIG_COMMON_CLK_RK808) += clk-rk808.o
obj-$(CONFIG_COMMON_CLK_S2MPS11) += clk-s2mps11.o
obj-$(CONFIG_COMMON_CLK_SI5351) += clk-si5351.o
obj-$(CONFIG_COMMON_CLK_SI570) += clk-si570.o
diff --git a/drivers/clk/clk-rk808.c b/drivers/clk/clk-rk808.c
new file mode 100644
index 0000000..14176bc
--- /dev/null
+++ b/drivers/clk/clk-rk808.c
@@ -0,0 +1,147 @@
+/*
+ * Clkout driver for Rockchip RK808
+ *
+ * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * Author: Chris Zhong <zyw@rock-chips.com>
+ * Author: Zhang Qing <zhangqing@rock-chips.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/rk808.h>
+#include <linux/i2c.h>
+
+struct rk808_clk {
+ struct rk808 *rk808;
+ struct clk_onecell_data clk_data;
+ struct clk_hw clkout1_hw;
+ struct clk_hw clkout2_hw;
+};
+
+static unsigned long rk808_clkout_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return 32768;
+}
+
+static int rk808_clkout1_is_prepared(struct clk_hw *hw)
+{
+ return 1;
+}
+
+static int rk808_clkout2_control(struct clk_hw *hw, bool enable)
+{
+ struct rk808_clk *rk808_clk = container_of(hw, struct rk808_clk,
+ clkout2_hw);
+ struct rk808 *rk808 = rk808_clk->rk808;
+
+ return regmap_update_bits(rk808->regmap, RK808_CLK32OUT_REG,
+ CLK32KOUT2_EN, enable ? CLK32KOUT2_EN : 0);
+}
+
+static int rk808_clkout2_prepare(struct clk_hw *hw)
+{
+ return rk808_clkout2_control(hw, 1);
+}
+
+static void rk808_clkout2_unprepare(struct clk_hw *hw)
+{
+ rk808_clkout2_control(hw, 0);
+}
+
+static int rk808_clkout2_is_prepared(struct clk_hw *hw)
+{
+ struct rk808_clk *rk808_clk = container_of(hw, struct rk808_clk,
+ clkout2_hw);
+ struct rk808 *rk808 = rk808_clk->rk808;
+ uint32_t val;
+
+ int ret = regmap_read(rk808->regmap, RK808_CLK32OUT_REG, &val);
+
+ if (ret < 0)
+ return ret;
+
+ return (val & CLK32KOUT2_EN) ? 1 : 0;
+}
+
+static const struct clk_ops rk808_clkout1_ops = {
+ .is_prepared = rk808_clkout1_is_prepared,
+ .recalc_rate = rk808_clkout_recalc_rate,
+};
+
+static const struct clk_ops rk808_clkout2_ops = {
+ .prepare = rk808_clkout2_prepare,
+ .unprepare = rk808_clkout2_unprepare,
+ .is_prepared = rk808_clkout2_is_prepared,
+ .recalc_rate = rk808_clkout_recalc_rate,
+};
+
+static int rk808_clk_probe(struct platform_device *pdev)
+{
+ struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
+ struct i2c_client *client = rk808->i2c;
+ struct device_node *node = client->dev.of_node;
+ struct clk_init_data init;
+ struct clk **clk_table;
+ struct rk808_clk *rk808_clk;
+
+ rk808_clk = devm_kzalloc(&pdev->dev, sizeof(*rk808_clk), GFP_KERNEL);
+ if (!rk808_clk)
+ return -ENOMEM;
+
+ rk808_clk->rk808 = rk808;
+
+ clk_table = devm_kzalloc(&client->dev,
+ 2*sizeof(struct clk *), GFP_KERNEL);
+ if (!clk_table)
+ return -ENOMEM;
+
+ init.flags = CLK_IS_ROOT;
+ init.parent_names = NULL;
+ init.num_parents = 0;
+ init.name = "rk808-clkout1";
+ init.ops = &rk808_clkout1_ops;
+ rk808_clk->clkout1_hw.init = &init;
+ clk_table[0] = devm_clk_register(&pdev->dev, &rk808_clk->clkout1_hw);
+
+ init.name = "rk808-clkout2";
+ init.ops = &rk808_clkout2_ops;
+ rk808_clk->clkout2_hw.init = &init;
+ clk_table[1] = devm_clk_register(&pdev->dev, &rk808_clk->clkout2_hw);
+
+ rk808_clk->clk_data.clks = clk_table;
+ rk808_clk->clk_data.clk_num = 2;
+ of_clk_add_provider(node, of_clk_src_onecell_get, clk_table);
+
+ return 0;
+}
+
+static struct platform_driver rk808_clk_driver = {
+ .probe = rk808_clk_probe,
+ .driver = {
+ .name = "rk808-clkout",
+ .owner = THIS_MODULE,
+ },
+};
+
+module_platform_driver(rk808_clk_driver);
+
+MODULE_DESCRIPTION("Clkout driver for the rk808 series PMICs");
+MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
+MODULE_AUTHOR("Zhang Qing <zhanqging@rock-chips.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:rk808-clk");
--
1.7.9.5
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2014-08-25 4:04 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-08-23 11:07 [PATCH v3 5/5] Clk: RK808: Add clkout driver for RK808 Chris Zhong
2014-08-25 4:04 ` Doug Anderson
-- strict thread matches above, loose matches on Subject: below --
2014-08-21 13:37 Chris Zhong
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).