* [PATCH v3 1/5] MFD: Add rk808 device tree bindings documentation
@ 2014-08-23 10:29 Chris Zhong
2014-08-25 4:18 ` Doug Anderson
0 siblings, 1 reply; 4+ messages in thread
From: Chris Zhong @ 2014-08-23 10:29 UTC (permalink / raw)
To: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, sameo,
lee.jones, lgirdwood, broonie, a.zummo, mturquette
Cc: devicetree, linux-kernel, rtc-linux, grant.likely, hl, huangtao,
cf, zhangqing, xxx, dianders, heiko, olof, sonnyrao, dtor,
javier.martinez, kever.yang, Chris Zhong
rk808.txt: Add device tree bindings for rockchip's rk808 pmic.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
---
Changes in v4:
Adviced by doug
- add "clock-output-names" propertiey
- add a header file "rockchip,rk808.h"
Changes in v3:
- fix compile err
Changes in v2:
Adviced by javier.martinez
- separated from rtc-rk808.c
Documentation/devicetree/bindings/mfd/rk808.txt | 133 +++++++++++++++++++++++
1 file changed, 133 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rk808.txt
diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
new file mode 100644
index 0000000..a9368fc
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rk808.txt
@@ -0,0 +1,133 @@
+RK808 Power Management Integrated Circuit
+
+Required properties:
+- compatible: "rockchip,rk808"
+- reg: I2C slave address
+- interrupt-parent: The parent interrupt controller.
+- interrupts: the interrupt outputs of the controller.
+- pinctrl-names: Should contain only one value - "default".
+- pinctrl-0: Should specify pin control groups used for this controller.
+- regulators: This is the list of child nodes that specify the regulator
+ initialization data for defined regulators. Not all regulators for the given
+ device need to be present. The definition for each of these nodes is defined
+ using the standard binding for regulators found at
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+- #clock-cells: the value should be 1
+
+Optional properties:
+- clock-output-names : From common clock binding to override the
+ default output clock name
+- rockchip,system-power-controller: Telling whether or not this pmic is controlling
+ the system power.
+
+Example:
+rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ interrupt-parent = <&gpio0>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>;
+ reg = <0x1b>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k0", "xin32k1";
+ rockchip,system-power-controller;
+
+ regulators {
+ rk808_dcdc1_reg: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdd_arm";
+ };
+
+ rk808_dcdc2_reg: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd_gpu";
+ };
+
+ rk808_dcdc3_reg: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vdd_ddr";
+ };
+
+ rk808_dcdc4_reg: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio";
+ };
+
+ rk808_ldo1_reg: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_ldo2_reg: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_ldo3_reg: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "LDO_REG3";
+ };
+
+ rk808_ldo4_reg: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ rk808_ldo5_reg: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_ldo6_reg: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ rk808_ldo7_reg: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ rk808_ldo8_reg: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_switch1_reg: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ rk808_switch2_reg: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
--
1.7.9.5
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH v3 1/5] MFD: Add rk808 device tree bindings documentation
2014-08-23 10:29 [PATCH v3 1/5] MFD: Add rk808 device tree bindings documentation Chris Zhong
@ 2014-08-25 4:18 ` Doug Anderson
0 siblings, 0 replies; 4+ messages in thread
From: Doug Anderson @ 2014-08-25 4:18 UTC (permalink / raw)
To: Chris Zhong
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Samuel Ortiz, Lee Jones, Liam Girdwood, broonie,
Alessandro Zummo, Mike Turquette, devicetree, linux-kernel,
rtc-linux, Grant Likely, Lin Huang, Tao Huang, Eddie Cai,
zhangqing, xxx, Heiko Stübner, Olof Johansson, Sonny Rao,
Dmitry Torokhov, Javier Martinez Canillas, Kever Yang
Chris,
On Sat, Aug 23, 2014 at 3:29 AM, Chris Zhong <zyw@rock-chips.com> wrote:
> rk808.txt: Add device tree bindings for rockchip's rk808 pmic.
>
> Signed-off-by: Chris Zhong <zyw@rock-chips.com>
>
> ---
>
> Changes in v4:
> Adviced by doug
> - add "clock-output-names" propertiey
> - add a header file "rockchip,rk808.h"
>
> Changes in v3:
> - fix compile err
>
> Changes in v2:
> Adviced by javier.martinez
> - separated from rtc-rk808.c
>
> Documentation/devicetree/bindings/mfd/rk808.txt | 133 +++++++++++++++++++++++
> 1 file changed, 133 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/rk808.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
> new file mode 100644
> index 0000000..a9368fc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/rk808.txt
> @@ -0,0 +1,133 @@
> +RK808 Power Management Integrated Circuit
> +
> +Required properties:
> +- compatible: "rockchip,rk808"
> +- reg: I2C slave address
> +- interrupt-parent: The parent interrupt controller.
> +- interrupts: the interrupt outputs of the controller.
> +- pinctrl-names: Should contain only one value - "default".
> +- pinctrl-0: Should specify pin control groups used for this controller.
> +- regulators: This is the list of child nodes that specify the regulator
> + initialization data for defined regulators. Not all regulators for the given
> + device need to be present. The definition for each of these nodes is defined
> + using the standard binding for regulators found at
> + Documentation/devicetree/bindings/regulator/regulator.txt.
> +- #clock-cells: the value should be 1
Mark Brown said:
You need to identify all the valid names for regulators on the device so
people know which string to use for which regulator.
...and you haven't incorporated that feedback yet. The Example below
is not enough. You should have a string like:
The following are the names of the regulators that the rk808 pmic block
supports. Note: The 'n' below represents the number as per the datasheet:
- DCDC_REGn
- valid values for n are 1 to 3.
- LDO_REGn
- valid values for n are 1 to 8.
- SWITCH_REGn
- valid values for n are 1 to 2.
> +
> +Optional properties:
> +- clock-output-names : From common clock binding to override the
> + default output clock name
> +- rockchip,system-power-controller: Telling whether or not this pmic is controlling
> + the system power.
> +
> +Example:
> +rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int>;
> + reg = <0x1b>;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k0", "xin32k1";
> + rockchip,system-power-controller;
> +
> + regulators {
> + rk808_dcdc1_reg: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vdd_arm";
> + };
> +
> + rk808_dcdc2_reg: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd_gpu";
> + };
> +
> + rk808_dcdc3_reg: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vdd_ddr";
> + };
> +
> + rk808_dcdc4_reg: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio";
> + };
> +
> + rk808_ldo1_reg: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo2_reg: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo3_reg: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "LDO_REG3";
> + };
> +
> + rk808_ldo4_reg: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + rk808_ldo5_reg: LDO_REG5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo6_reg: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + };
> +
> + rk808_ldo7_reg: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + rk808_ldo8_reg: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_switch1_reg: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + rk808_switch2_reg: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + };
> + };
> + };
> --
> 1.7.9.5
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH v3 1/5] MFD: Add rk808 device tree bindings documentation
2014-08-21 13:27 Chris Zhong
@ 2014-08-22 17:23 ` Doug Anderson
0 siblings, 0 replies; 4+ messages in thread
From: Doug Anderson @ 2014-08-22 17:23 UTC (permalink / raw)
To: Chris Zhong
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Samuel Ortiz, Lee Jones, Liam Girdwood, broonie,
Alessandro Zummo, Mike Turquette, devicetree, linux-kernel,
rtc-linux, Grant Likely, Lin Huang, Tao Huang, Eddie Cai,
zhangqing, xxx, Heiko Stübner, Olof Johansson, Sonny Rao,
Dmitry Torokhov, Javier Martinez Canillas, Kever Yang
Chris,
On Thu, Aug 21, 2014 at 6:27 AM, Chris Zhong <zyw@rock-chips.com> wrote:
> rk808.txt: Add device tree bindings for rockchip's rk808 pmic.
>
> Signed-off-by: Chris Zhong <zyw@rock-chips.com>
>
> ---
>
> Changes in v3:
> - fix compile err
Please make sure to address comments that were made against your v2
version, too.
>
> Changes in v2:
> Adviced by javier.martinez
> - separated from rtc-rk808.c
>
> Documentation/devicetree/bindings/mfd/rk808.txt | 128 +++++++++++++++++++++++
> 1 file changed, 128 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/rk808.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
> new file mode 100644
> index 0000000..876291d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/rk808.txt
> @@ -0,0 +1,128 @@
> +RK808 Power Management Integrated Circuit
> +
> +Required properties:
> +- compatible: "rockchip,rk808"
> +- reg: I2C slave address
> +- interrupt-parent: The parent interrupt controller.
> +- interrupts: the interrupt outputs of the controller.
> +- pinctrl-names: Should contain only one value - "default".
> +- pinctrl-0: Should specify pin control groups used for this controller.
> +- regulators: This is the list of child nodes that specify the regulator
> + initialization data for defined regulators. Not all regulators for the given
> + device need to be present. The definition for each of these nodes is defined
> + using the standard binding for regulators found at
> + Documentation/devicetree/bindings/regulator/regulator.txt.
I think you need a "#clock-cells = <1>;" in here. You should also
create a "include/dt-bindings/clock/rockchip,rk808.h" file that lists
numbers for your two clocks.
> +Optional properties:
> +- rockchip,system-power-controller: Telling whether or not this pmic is controlling
> + the system power.
You should add "clock-output-names" as haoyu,hym8563.txt has.
> +
> +Example:
> +rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int>;
> + reg = <0x1b>;
> + rockchip,system-power-controller;
> +
> + regulators {
> + rk808_dcdc1_reg: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vdd_arm";
> + };
> +
> + rk808_dcdc2_reg: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd_gpu";
> + };
> +
> + rk808_dcdc3_reg: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vdd_ddr";
> + };
> +
> + rk808_dcdc4_reg: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio";
> + };
> +
> + rk808_ldo1_reg: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo2_reg: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo3_reg: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "LDO_REG3";
> + };
> +
> + rk808_ldo4_reg: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + rk808_ldo5_reg: LDO_REG5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo6_reg: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + };
> +
> + rk808_ldo7_reg: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + rk808_ldo8_reg: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_switch1_reg: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + rk808_switch2_reg: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + };
> + };
> + };
> --
> 1.7.9.5
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v3 1/5] MFD: Add rk808 device tree bindings documentation
@ 2014-08-21 13:27 Chris Zhong
2014-08-22 17:23 ` Doug Anderson
0 siblings, 1 reply; 4+ messages in thread
From: Chris Zhong @ 2014-08-21 13:27 UTC (permalink / raw)
To: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, sameo,
lee.jones, lgirdwood, broonie, a.zummo, mturquette
Cc: devicetree, linux-kernel, rtc-linux, grant.likely, hl, huangtao,
cf, zhangqing, xxx, dianders, heiko, olof, sonnyrao, dtor,
javier.martinez, kever.yang, Chris Zhong
rk808.txt: Add device tree bindings for rockchip's rk808 pmic.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
---
Changes in v3:
- fix compile err
Changes in v2:
Adviced by javier.martinez
- separated from rtc-rk808.c
Documentation/devicetree/bindings/mfd/rk808.txt | 128 +++++++++++++++++++++++
1 file changed, 128 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rk808.txt
diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
new file mode 100644
index 0000000..876291d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rk808.txt
@@ -0,0 +1,128 @@
+RK808 Power Management Integrated Circuit
+
+Required properties:
+- compatible: "rockchip,rk808"
+- reg: I2C slave address
+- interrupt-parent: The parent interrupt controller.
+- interrupts: the interrupt outputs of the controller.
+- pinctrl-names: Should contain only one value - "default".
+- pinctrl-0: Should specify pin control groups used for this controller.
+- regulators: This is the list of child nodes that specify the regulator
+ initialization data for defined regulators. Not all regulators for the given
+ device need to be present. The definition for each of these nodes is defined
+ using the standard binding for regulators found at
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+- rockchip,system-power-controller: Telling whether or not this pmic is controlling
+ the system power.
+
+Example:
+rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ interrupt-parent = <&gpio0>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>;
+ reg = <0x1b>;
+ rockchip,system-power-controller;
+
+ regulators {
+ rk808_dcdc1_reg: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdd_arm";
+ };
+
+ rk808_dcdc2_reg: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd_gpu";
+ };
+
+ rk808_dcdc3_reg: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vdd_ddr";
+ };
+
+ rk808_dcdc4_reg: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio";
+ };
+
+ rk808_ldo1_reg: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_ldo2_reg: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_ldo3_reg: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "LDO_REG3";
+ };
+
+ rk808_ldo4_reg: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ rk808_ldo5_reg: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_ldo6_reg: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ rk808_ldo7_reg: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ rk808_ldo8_reg: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_switch1_reg: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ rk808_switch2_reg: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
--
1.7.9.5
^ permalink raw reply related [flat|nested] 4+ messages in thread
end of thread, other threads:[~2014-08-25 4:19 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-08-23 10:29 [PATCH v3 1/5] MFD: Add rk808 device tree bindings documentation Chris Zhong
2014-08-25 4:18 ` Doug Anderson
-- strict thread matches above, loose matches on Subject: below --
2014-08-21 13:27 Chris Zhong
2014-08-22 17:23 ` Doug Anderson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).