[PATCH 0/4] Add required changes to ufshcd to support exynos ufs hci

[PATCH 0/4] Add required changes to ufshcd to support exynos ufs hci

[Alim Akhtar]

Hi All

These patches are part of a larger patch series [1] which attempts upstreaming
EXYNOS UFS driver support. There was not much activities after v5 of that
series. In between I saw there were other teams in Samsung tried upstreaming
the same, but that has not really gone anywhere.
I have taken this task again and here is another attempt to upstream exynos-ufs
driver support. I have divided the patches into two series, one which adds
required infra in the ufshcd core needed by exynos-ufs driver and other part
will have actual exynos-ufs driver. Splitting this has a advantage of less
reviewing over head.

I am floating these as a new patch set.

[1] https://www.spinics.net/lists/linux-scsi/msg90292.html

These patches are based on mainline v4.17-rc3.

Alim Akhtar (4):
  scsi: ufs: add quirk to fix mishandling utrlclr/utmrlclr
  scsi: ufs: add quirk not to allow reset of interrupt aggregation
  scsi: ufs: add quirk to enable host controller without hce
  scsi: ufs: make ufshcd_config_pwr_mode of non-static func

 drivers/scsi/ufs/ufshcd.c | 104 ++++++++++++++++++++++++++++++++++++++++++----
 drivers/scsi/ufs/ufshcd.h |  18 ++++++++
 2 files changed, 114 insertions(+), 8 deletions(-)

-- 
2.7.4

[PATCH 1/4] scsi: ufs: add quirk to fix mishandling utrlclr/utmrlclr

[Alim Akhtar]

In the right behavior, setting the bit to '0' indicates clear and
'1' indicates no change. If host controller handles this the other way,
UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR can be used.

Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 drivers/scsi/ufs/ufshcd.c | 21 +++++++++++++++++++--
 drivers/scsi/ufs/ufshcd.h |  5 +++++
 2 files changed, 24 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 00e7905..9898ce5 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -675,7 +675,24 @@ static inline void ufshcd_put_tm_slot(struct ufs_hba *hba, int slot)
  */
 static inline void ufshcd_utrl_clear(struct ufs_hba *hba, u32 pos)
 {
-	ufshcd_writel(hba, ~(1 << pos), REG_UTP_TRANSFER_REQ_LIST_CLEAR);
+	if (hba->quirks & UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR)
+		ufshcd_writel(hba, (1 << pos), REG_UTP_TRANSFER_REQ_LIST_CLEAR);
+	else
+		ufshcd_writel(hba, ~(1 << pos),
+				REG_UTP_TRANSFER_REQ_LIST_CLEAR);
+}
+
+/**
+ * ufshcd_utmrl_clear - Clear a bit in UTRMLCLR register
+ * @hba: per adapter instance
+ * @pos: position of the bit to be cleared
+ */
+static inline void ufshcd_utmrl_clear(struct ufs_hba *hba, u32 pos)
+{
+	if (hba->quirks & UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR)
+		ufshcd_writel(hba, (1 << pos), REG_UTP_TASK_REQ_LIST_CLEAR);
+	else
+		ufshcd_writel(hba, ~(1 << pos), REG_UTP_TASK_REQ_LIST_CLEAR);
 }
 
 /**
@@ -5398,7 +5415,7 @@ static int ufshcd_clear_tm_cmd(struct ufs_hba *hba, int tag)
 		goto out;
 
 	spin_lock_irqsave(hba->host->host_lock, flags);
-	ufshcd_writel(hba, ~(1 << tag), REG_UTP_TASK_REQ_LIST_CLEAR);
+	ufshcd_utmrl_clear(hba, tag);
 	spin_unlock_irqrestore(hba->host->host_lock, flags);
 
 	/* poll for max. 1 sec to clear door bell register by h/w */
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index 8110dcd..43035f8 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -595,6 +595,11 @@ struct ufs_hba {
 	 */
 	#define UFSHCD_QUIRK_PRDT_BYTE_GRAN			0x80
 
+	/*
+	 * Cleaer handling for transfer/task request list is just opposite.
+	 */
+	#define UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR		0x100
+
 	unsigned int quirks;	/* Deviations from standard UFSHCI spec. */
 
 	/* Device deviations from standard UFS device spec. */
-- 
2.7.4

[PATCH 2/4] scsi: ufs: add quirk not to allow reset of interrupt aggregation

[Alim Akhtar]

Some host controller supports interrupt aggregation, but doesn't
allow to reset counter and timer by s/w.

Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 drivers/scsi/ufs/ufshcd.c | 3 ++-
 drivers/scsi/ufs/ufshcd.h | 6 ++++++
 2 files changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 9898ce5..253257c 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -4695,7 +4695,8 @@ static void ufshcd_transfer_req_compl(struct ufs_hba *hba)
 	 * false interrupt if device completes another request after resetting
 	 * aggregation and before reading the DB.
 	 */
-	if (ufshcd_is_intr_aggr_allowed(hba))
+	if (ufshcd_is_intr_aggr_allowed(hba) &&
+	    !(hba->quirks & UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR))
 		ufshcd_reset_intr_aggr(hba);
 
 	tr_doorbell = ufshcd_readl(hba, REG_UTP_TRANSFER_REQ_DOOR_BELL);
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index 43035f8..5c91ff1 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -600,6 +600,12 @@ struct ufs_hba {
 	 */
 	#define UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR		0x100
 
+	/*
+	 * This quirk needs to be enabled if host controller doesn't allow
+	 * that the interrupt aggregation timer and counter are reset by s/w.
+	 */
+	#define UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR		0x200
+
 	unsigned int quirks;	/* Deviations from standard UFSHCI spec. */
 
 	/* Device deviations from standard UFS device spec. */
-- 
2.7.4

[PATCH 3/4] scsi: ufs: add quirk to enable host controller without hce

[Alim Akhtar]

Some host controller doesn't support host controller enable via HCE.

Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 drivers/scsi/ufs/ufshcd.c | 75 +++++++++++++++++++++++++++++++++++++++++++++--
 drivers/scsi/ufs/ufshcd.h |  5 ++++
 2 files changed, 78 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 253257c..5bfd385 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -3400,6 +3400,52 @@ static int ufshcd_dme_link_startup(struct ufs_hba *hba)
 			"dme-link-startup: error code %d\n", ret);
 	return ret;
 }
+/**
+ * ufshcd_dme_reset - UIC command for DME_RESET
+ * @hba: per adapter instance
+ *
+ * DME_RESET command is issued in order to reset UniPro stack.
+ * This function now deal with cold reset.
+ *
+ * Returns 0 on success, non-zero value on failure
+ */
+static int ufshcd_dme_reset(struct ufs_hba *hba)
+{
+	struct uic_command uic_cmd = {0};
+	int ret;
+
+	uic_cmd.command = UIC_CMD_DME_RESET;
+
+	ret = ufshcd_send_uic_cmd(hba, &uic_cmd);
+	if (ret)
+		dev_err(hba->dev,
+			"dme-reset: error code %d\n", ret);
+
+	return ret;
+}
+
+/**
+ * ufshcd_dme_enable - UIC command for DME_ENABLE
+ * @hba: per adapter instance
+ *
+ * DME_ENABLE command is issued in order to enable UniPro stack.
+ *
+ * Returns 0 on success, non-zero value on failure
+ */
+static int ufshcd_dme_enable(struct ufs_hba *hba)
+{
+	struct uic_command uic_cmd = {0};
+	int ret;
+
+	uic_cmd.command = UIC_CMD_DME_ENABLE;
+
+	ret = ufshcd_send_uic_cmd(hba, &uic_cmd);
+	if (ret)
+		dev_err(hba->dev,
+			"dme-reset: error code %d\n", ret);
+
+	return ret;
+}
 
 static inline void ufshcd_add_delay_before_dme_cmd(struct ufs_hba *hba)
 {
@@ -4058,7 +4104,7 @@ static inline void ufshcd_hba_stop(struct ufs_hba *hba, bool can_sleep)
 }
 
 /**
- * ufshcd_hba_enable - initialize the controller
+ * ufshcd_hba_execute_hce - initialize the controller
  * @hba: per adapter instance
  *
  * The controller resets itself and controller firmware initialization
@@ -4067,7 +4113,7 @@ static inline void ufshcd_hba_stop(struct ufs_hba *hba, bool can_sleep)
  *
  * Returns 0 on success, non-zero value on failure
  */
-static int ufshcd_hba_enable(struct ufs_hba *hba)
+static int ufshcd_hba_execute_hce(struct ufs_hba *hba)
 {
 	int retry;
 
@@ -4122,6 +4168,31 @@ static int ufshcd_hba_enable(struct ufs_hba *hba)
 	return 0;
 }
 
+static int ufshcd_hba_enable(struct ufs_hba *hba)
+{
+	int ret;
+
+	if (hba->quirks & UFSHCI_QUIRK_BROKEN_HCE) {
+		ufshcd_set_link_off(hba);
+		ufshcd_vops_hce_enable_notify(hba, PRE_CHANGE);
+
+		/* enable UIC related interrupts */
+		ufshcd_enable_intr(hba, UFSHCD_UIC_MASK);
+		ret = ufshcd_dme_reset(hba);
+		if (!ret) {
+			ret = ufshcd_dme_enable(hba);
+			if (!ret)
+				ufshcd_vops_hce_enable_notify(hba, POST_CHANGE);
+			if (ret)
+				dev_err(hba->dev,
+					"Host controller enable failed with non-hce\n");
+		}
+	} else {
+		ret = ufshcd_hba_execute_hce(hba);
+	}
+
+	return ret;
+}
 static int ufshcd_disable_tx_lcc(struct ufs_hba *hba, bool peer)
 {
 	int tx_lanes, i, err = 0;
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index 5c91ff1..013a07e 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -606,6 +606,11 @@ struct ufs_hba {
 	 */
 	#define UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR		0x200
 
+	/*
+	 * This quirks needs to be enabled if host controller cannot be
+	 * enabled via HCE register.
+	 */
+	#define UFSHCI_QUIRK_BROKEN_HCE				0x400
 	unsigned int quirks;	/* Deviations from standard UFSHCI spec. */
 
 	/* Device deviations from standard UFS device spec. */
-- 
2.7.4

[PATCH 4/4] scsi: ufs: make ufshcd_config_pwr_mode of non-static func

[Alim Akhtar]

This makes ufshcd_config_pwr_mode non-static so that other vendors
like exynos can use the same.

Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 drivers/scsi/ufs/ufshcd.c | 5 ++---
 drivers/scsi/ufs/ufshcd.h | 2 ++
 2 files changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 5bfd385..68aefcd 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -233,8 +233,6 @@ static void ufshcd_suspend_clkscaling(struct ufs_hba *hba);
 static void __ufshcd_suspend_clkscaling(struct ufs_hba *hba);
 static int ufshcd_scale_clks(struct ufs_hba *hba, bool scale_up);
 static irqreturn_t ufshcd_intr(int irq, void *__hba);
-static int ufshcd_config_pwr_mode(struct ufs_hba *hba,
-		struct ufs_pa_layer_attr *desired_pwr_mode);
 static int ufshcd_change_power_mode(struct ufs_hba *hba,
 			     struct ufs_pa_layer_attr *pwr_mode);
 static inline bool ufshcd_valid_tag(struct ufs_hba *hba, int tag)
@@ -3969,7 +3967,7 @@ static int ufshcd_change_power_mode(struct ufs_hba *hba,
  * @hba: per-adapter instance
  * @desired_pwr_mode: desired power configuration
  */
-static int ufshcd_config_pwr_mode(struct ufs_hba *hba,
+int ufshcd_config_pwr_mode(struct ufs_hba *hba,
 		struct ufs_pa_layer_attr *desired_pwr_mode)
 {
 	struct ufs_pa_layer_attr final_params = { 0 };
@@ -3987,6 +3985,7 @@ static int ufshcd_config_pwr_mode(struct ufs_hba *hba,
 
 	return ret;
 }
+EXPORT_SYMBOL_GPL(ufshcd_config_pwr_mode);
 
 /**
  * ufshcd_complete_dev_init() - checks device readiness
diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index 013a07e..b42a5a3 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -805,6 +805,8 @@ extern int ufshcd_dme_set_attr(struct ufs_hba *hba, u32 attr_sel,
 			       u8 attr_set, u32 mib_val, u8 peer);
 extern int ufshcd_dme_get_attr(struct ufs_hba *hba, u32 attr_sel,
 			       u32 *mib_val, u8 peer);
+extern int ufshcd_config_pwr_mode(struct ufs_hba *hba,
+			struct ufs_pa_layer_attr *desired_pwr_mode);
 
 /* UIC command interfaces for DME primitives */
 #define DME_LOCAL	0
-- 
2.7.4

Re: [PATCH 0/4] Add required changes to ufshcd to support exynos ufs hci

[Alim Akhtar]

Hi All,

Any thought on this patch set?


On Sun, May 6, 2018 at 3:44 PM, Alim Akhtar <alim.akhtar@samsung.com> wrote:
> Hi All
>
> These patches are part of a larger patch series [1] which attempts upstreaming
> EXYNOS UFS driver support. There was not much activities after v5 of that
> series. In between I saw there were other teams in Samsung tried upstreaming
> the same, but that has not really gone anywhere.
> I have taken this task again and here is another attempt to upstream exynos-ufs
> driver support. I have divided the patches into two series, one which adds
> required infra in the ufshcd core needed by exynos-ufs driver and other part
> will have actual exynos-ufs driver. Splitting this has a advantage of less
> reviewing over head.
>
> I am floating these as a new patch set.
>
> [1] https://www.spinics.net/lists/linux-scsi/msg90292.html
>
> These patches are based on mainline v4.17-rc3.
>
> Alim Akhtar (4):
>   scsi: ufs: add quirk to fix mishandling utrlclr/utmrlclr
>   scsi: ufs: add quirk not to allow reset of interrupt aggregation
>   scsi: ufs: add quirk to enable host controller without hce
>   scsi: ufs: make ufshcd_config_pwr_mode of non-static func
>
>  drivers/scsi/ufs/ufshcd.c | 104 ++++++++++++++++++++++++++++++++++++++++++----
>  drivers/scsi/ufs/ufshcd.h |  18 ++++++++
>  2 files changed, 114 insertions(+), 8 deletions(-)
>
> --
> 2.7.4
>



-- 
Regards,
Alim

RE: [PATCH 4/4] scsi: ufs: make ufshcd_config_pwr_mode of non-static func

[Avri Altman]

> -----Original Message-----
> From: linux-scsi-owner@vger.kernel.org <linux-scsi-owner@vger.kernel.org>
> On Behalf Of Alim Akhtar
> Sent: Sunday, May 06, 2018 1:14 PM
> To: linux-scsi@vger.kernel.org; linux-kernel@vger.kernel.org
> Cc: jejb@linux.vnet.ibm.com; martin.petersen@oracle.com;
> vivek.gautam@codeaurora.org; subhashj@codeaurora.org;
> vinholikatti@gmail.com; olof@lixom.net; alim.akhtar@samsung.com
> Subject: [PATCH 4/4] scsi: ufs: make ufshcd_config_pwr_mode of non-static
> func
> 
> This makes ufshcd_config_pwr_mode non-static so that other vendors like
> exynos can use the same.
> 
> Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Avri Altman <avri.altman@wdc.com>

Might be also useful exporting an API for all uic commands?

Thanks,
Avri 

Re: [PATCH 1/4] scsi: ufs: add quirk to fix mishandling utrlclr/utmrlclr

[Subhash Jadavani]

On 2018-05-06 03:14, Alim Akhtar wrote:
> In the right behavior, setting the bit to '0' indicates clear and
> '1' indicates no change. If host controller handles this the other way,
> UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR can be used.
> 
> Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> ---
>  drivers/scsi/ufs/ufshcd.c | 21 +++++++++++++++++++--
>  drivers/scsi/ufs/ufshcd.h |  5 +++++
>  2 files changed, 24 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index 00e7905..9898ce5 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -675,7 +675,24 @@ static inline void ufshcd_put_tm_slot(struct
> ufs_hba *hba, int slot)
>   */
>  static inline void ufshcd_utrl_clear(struct ufs_hba *hba, u32 pos)
>  {
> -	ufshcd_writel(hba, ~(1 << pos), REG_UTP_TRANSFER_REQ_LIST_CLEAR);
> +	if (hba->quirks & UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR)
> +		ufshcd_writel(hba, (1 << pos), REG_UTP_TRANSFER_REQ_LIST_CLEAR);
> +	else
> +		ufshcd_writel(hba, ~(1 << pos),
> +				REG_UTP_TRANSFER_REQ_LIST_CLEAR);
> +}
> +
> +/**
> + * ufshcd_utmrl_clear - Clear a bit in UTRMLCLR register
> + * @hba: per adapter instance
> + * @pos: position of the bit to be cleared
> + */
> +static inline void ufshcd_utmrl_clear(struct ufs_hba *hba, u32 pos)
> +{
> +	if (hba->quirks & UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR)
> +		ufshcd_writel(hba, (1 << pos), REG_UTP_TASK_REQ_LIST_CLEAR);
> +	else
> +		ufshcd_writel(hba, ~(1 << pos), REG_UTP_TASK_REQ_LIST_CLEAR);
>  }
> 
>  /**
> @@ -5398,7 +5415,7 @@ static int ufshcd_clear_tm_cmd(struct ufs_hba
> *hba, int tag)
>  		goto out;
> 
>  	spin_lock_irqsave(hba->host->host_lock, flags);
> -	ufshcd_writel(hba, ~(1 << tag), REG_UTP_TASK_REQ_LIST_CLEAR);
> +	ufshcd_utmrl_clear(hba, tag);
>  	spin_unlock_irqrestore(hba->host->host_lock, flags);
> 
>  	/* poll for max. 1 sec to clear door bell register by h/w */
> diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
> index 8110dcd..43035f8 100644
> --- a/drivers/scsi/ufs/ufshcd.h
> +++ b/drivers/scsi/ufs/ufshcd.h
> @@ -595,6 +595,11 @@ struct ufs_hba {
>  	 */
>  	#define UFSHCD_QUIRK_PRDT_BYTE_GRAN			0x80
> 
> +	/*
> +	 * Cleaer handling for transfer/task request list is just opposite.
> +	 */
> +	#define UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR		0x100
> +
>  	unsigned int quirks;	/* Deviations from standard UFSHCI spec. */
> 
>  	/* Device deviations from standard UFS device spec. */

Looks good to me.
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>

-- 
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH 2/4] scsi: ufs: add quirk not to allow reset of interrupt aggregation

[Subhash Jadavani]

On 2018-05-06 03:14, Alim Akhtar wrote:
> Some host controller supports interrupt aggregation, but doesn't
> allow to reset counter and timer by s/w.
> 
> Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> ---
>  drivers/scsi/ufs/ufshcd.c | 3 ++-
>  drivers/scsi/ufs/ufshcd.h | 6 ++++++
>  2 files changed, 8 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index 9898ce5..253257c 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -4695,7 +4695,8 @@ static void ufshcd_transfer_req_compl(struct 
> ufs_hba *hba)
>  	 * false interrupt if device completes another request after 
> resetting
>  	 * aggregation and before reading the DB.
>  	 */
> -	if (ufshcd_is_intr_aggr_allowed(hba))
> +	if (ufshcd_is_intr_aggr_allowed(hba) &&
> +	    !(hba->quirks & UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR))
>  		ufshcd_reset_intr_aggr(hba);
> 
>  	tr_doorbell = ufshcd_readl(hba, REG_UTP_TRANSFER_REQ_DOOR_BELL);
> diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
> index 43035f8..5c91ff1 100644
> --- a/drivers/scsi/ufs/ufshcd.h
> +++ b/drivers/scsi/ufs/ufshcd.h
> @@ -600,6 +600,12 @@ struct ufs_hba {
>  	 */
>  	#define UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR		0x100
> 
> +	/*
> +	 * This quirk needs to be enabled if host controller doesn't allow
> +	 * that the interrupt aggregation timer and counter are reset by s/w.
> +	 */
> +	#define UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR		0x200
> +
>  	unsigned int quirks;	/* Deviations from standard UFSHCI spec. */
> 
>  	/* Device deviations from standard UFS device spec. */

Looks good to me.
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>

-- 
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH 3/4] scsi: ufs: add quirk to enable host controller without hce

[Subhash Jadavani]

On 2018-05-06 03:14, Alim Akhtar wrote:
> Some host controller doesn't support host controller enable via HCE.
> 
> Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> ---
>  drivers/scsi/ufs/ufshcd.c | 75 
> +++++++++++++++++++++++++++++++++++++++++++++--
>  drivers/scsi/ufs/ufshcd.h |  5 ++++
>  2 files changed, 78 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index 253257c..5bfd385 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -3400,6 +3400,52 @@ static int ufshcd_dme_link_startup(struct 
> ufs_hba *hba)
>  			"dme-link-startup: error code %d\n", ret);
>  	return ret;
>  }
> +/**
> + * ufshcd_dme_reset - UIC command for DME_RESET
> + * @hba: per adapter instance
> + *
> + * DME_RESET command is issued in order to reset UniPro stack.
> + * This function now deal with cold reset.
> + *
> + * Returns 0 on success, non-zero value on failure
> + */
> +static int ufshcd_dme_reset(struct ufs_hba *hba)
> +{
> +	struct uic_command uic_cmd = {0};
> +	int ret;
> +
> +	uic_cmd.command = UIC_CMD_DME_RESET;
> +
> +	ret = ufshcd_send_uic_cmd(hba, &uic_cmd);
> +	if (ret)
> +		dev_err(hba->dev,
> +			"dme-reset: error code %d\n", ret);
> +
> +	return ret;
> +}
> +
> +/**
> + * ufshcd_dme_enable - UIC command for DME_ENABLE
> + * @hba: per adapter instance
> + *
> + * DME_ENABLE command is issued in order to enable UniPro stack.
> + *
> + * Returns 0 on success, non-zero value on failure
> + */
> +static int ufshcd_dme_enable(struct ufs_hba *hba)
> +{
> +	struct uic_command uic_cmd = {0};
> +	int ret;
> +
> +	uic_cmd.command = UIC_CMD_DME_ENABLE;
> +
> +	ret = ufshcd_send_uic_cmd(hba, &uic_cmd);
> +	if (ret)
> +		dev_err(hba->dev,
> +			"dme-reset: error code %d\n", ret);
> +
> +	return ret;
> +}
> 
>  static inline void ufshcd_add_delay_before_dme_cmd(struct ufs_hba 
> *hba)
>  {
> @@ -4058,7 +4104,7 @@ static inline void ufshcd_hba_stop(struct
> ufs_hba *hba, bool can_sleep)
>  }
> 
>  /**
> - * ufshcd_hba_enable - initialize the controller
> + * ufshcd_hba_execute_hce - initialize the controller
>   * @hba: per adapter instance
>   *
>   * The controller resets itself and controller firmware initialization
> @@ -4067,7 +4113,7 @@ static inline void ufshcd_hba_stop(struct
> ufs_hba *hba, bool can_sleep)
>   *
>   * Returns 0 on success, non-zero value on failure
>   */
> -static int ufshcd_hba_enable(struct ufs_hba *hba)
> +static int ufshcd_hba_execute_hce(struct ufs_hba *hba)
>  {
>  	int retry;
> 
> @@ -4122,6 +4168,31 @@ static int ufshcd_hba_enable(struct ufs_hba 
> *hba)
>  	return 0;
>  }
> 
> +static int ufshcd_hba_enable(struct ufs_hba *hba)
> +{
> +	int ret;
> +
> +	if (hba->quirks & UFSHCI_QUIRK_BROKEN_HCE) {
> +		ufshcd_set_link_off(hba);
> +		ufshcd_vops_hce_enable_notify(hba, PRE_CHANGE);
> +
> +		/* enable UIC related interrupts */
> +		ufshcd_enable_intr(hba, UFSHCD_UIC_MASK);
> +		ret = ufshcd_dme_reset(hba);
> +		if (!ret) {
> +			ret = ufshcd_dme_enable(hba);
> +			if (!ret)
> +				ufshcd_vops_hce_enable_notify(hba, POST_CHANGE);
> +			if (ret)
> +				dev_err(hba->dev,
> +					"Host controller enable failed with non-hce\n");
> +		}
> +	} else {
> +		ret = ufshcd_hba_execute_hce(hba);
> +	}
> +
> +	return ret;
> +}
>  static int ufshcd_disable_tx_lcc(struct ufs_hba *hba, bool peer)
>  {
>  	int tx_lanes, i, err = 0;
> diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
> index 5c91ff1..013a07e 100644
> --- a/drivers/scsi/ufs/ufshcd.h
> +++ b/drivers/scsi/ufs/ufshcd.h
> @@ -606,6 +606,11 @@ struct ufs_hba {
>  	 */
>  	#define UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR		0x200
> 
> +	/*
> +	 * This quirks needs to be enabled if host controller cannot be
> +	 * enabled via HCE register.
> +	 */
> +	#define UFSHCI_QUIRK_BROKEN_HCE				0x400
>  	unsigned int quirks;	/* Deviations from standard UFSHCI spec. */
> 
>  	/* Device deviations from standard UFS device spec. */

Looks good to me.
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>

-- 
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH 4/4] scsi: ufs: make ufshcd_config_pwr_mode of non-static func

[Subhash Jadavani]

On 2018-05-06 03:14, Alim Akhtar wrote:
> This makes ufshcd_config_pwr_mode non-static so that other vendors
> like exynos can use the same.
> 
> Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> ---
>  drivers/scsi/ufs/ufshcd.c | 5 ++---
>  drivers/scsi/ufs/ufshcd.h | 2 ++
>  2 files changed, 4 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index 5bfd385..68aefcd 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -233,8 +233,6 @@ static void ufshcd_suspend_clkscaling(struct 
> ufs_hba *hba);
>  static void __ufshcd_suspend_clkscaling(struct ufs_hba *hba);
>  static int ufshcd_scale_clks(struct ufs_hba *hba, bool scale_up);
>  static irqreturn_t ufshcd_intr(int irq, void *__hba);
> -static int ufshcd_config_pwr_mode(struct ufs_hba *hba,
> -		struct ufs_pa_layer_attr *desired_pwr_mode);
>  static int ufshcd_change_power_mode(struct ufs_hba *hba,
>  			     struct ufs_pa_layer_attr *pwr_mode);
>  static inline bool ufshcd_valid_tag(struct ufs_hba *hba, int tag)
> @@ -3969,7 +3967,7 @@ static int ufshcd_change_power_mode(struct 
> ufs_hba *hba,
>   * @hba: per-adapter instance
>   * @desired_pwr_mode: desired power configuration
>   */
> -static int ufshcd_config_pwr_mode(struct ufs_hba *hba,
> +int ufshcd_config_pwr_mode(struct ufs_hba *hba,
>  		struct ufs_pa_layer_attr *desired_pwr_mode)
>  {
>  	struct ufs_pa_layer_attr final_params = { 0 };
> @@ -3987,6 +3985,7 @@ static int ufshcd_config_pwr_mode(struct ufs_hba 
> *hba,
> 
>  	return ret;
>  }
> +EXPORT_SYMBOL_GPL(ufshcd_config_pwr_mode);
> 
>  /**
>   * ufshcd_complete_dev_init() - checks device readiness
> diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
> index 013a07e..b42a5a3 100644
> --- a/drivers/scsi/ufs/ufshcd.h
> +++ b/drivers/scsi/ufs/ufshcd.h
> @@ -805,6 +805,8 @@ extern int ufshcd_dme_set_attr(struct ufs_hba
> *hba, u32 attr_sel,
>  			       u8 attr_set, u32 mib_val, u8 peer);
>  extern int ufshcd_dme_get_attr(struct ufs_hba *hba, u32 attr_sel,
>  			       u32 *mib_val, u8 peer);
> +extern int ufshcd_config_pwr_mode(struct ufs_hba *hba,
> +			struct ufs_pa_layer_attr *desired_pwr_mode);
> 
>  /* UIC command interfaces for DME primitives */
>  #define DME_LOCAL	0

Looks good to me.
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>

-- 
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH 1/4] scsi: ufs: add quirk to fix mishandling utrlclr/utmrlclr

[Asutosh Das (asd)]

On 5/6/2018 3:44 PM, Alim Akhtar wrote:
> In the right behavior, setting the bit to '0' indicates clear and
> '1' indicates no change. If host controller handles this the other way,
> UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR can be used.
> 
> Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> ---
>   drivers/scsi/ufs/ufshcd.c | 21 +++++++++++++++++++--
>   drivers/scsi/ufs/ufshcd.h |  5 +++++
>   2 files changed, 24 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index 00e7905..9898ce5 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -675,7 +675,24 @@ static inline void ufshcd_put_tm_slot(struct ufs_hba *hba, int slot)
>    */
>   static inline void ufshcd_utrl_clear(struct ufs_hba *hba, u32 pos)
>   {
> -	ufshcd_writel(hba, ~(1 << pos), REG_UTP_TRANSFER_REQ_LIST_CLEAR);
> +	if (hba->quirks & UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR)
> +		ufshcd_writel(hba, (1 << pos), REG_UTP_TRANSFER_REQ_LIST_CLEAR);
> +	else
> +		ufshcd_writel(hba, ~(1 << pos),
> +				REG_UTP_TRANSFER_REQ_LIST_CLEAR);
> +}
> +
> +/**
> + * ufshcd_utmrl_clear - Clear a bit in UTRMLCLR register
> + * @hba: per adapter instance
> + * @pos: position of the bit to be cleared
> + */
> +static inline void ufshcd_utmrl_clear(struct ufs_hba *hba, u32 pos)
> +{
> +	if (hba->quirks & UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR)
> +		ufshcd_writel(hba, (1 << pos), REG_UTP_TASK_REQ_LIST_CLEAR);
> +	else
> +		ufshcd_writel(hba, ~(1 << pos), REG_UTP_TASK_REQ_LIST_CLEAR);
>   }
>   
>   /**
> @@ -5398,7 +5415,7 @@ static int ufshcd_clear_tm_cmd(struct ufs_hba *hba, int tag)
>   		goto out;
>   
>   	spin_lock_irqsave(hba->host->host_lock, flags);
> -	ufshcd_writel(hba, ~(1 << tag), REG_UTP_TASK_REQ_LIST_CLEAR);
> +	ufshcd_utmrl_clear(hba, tag);
>   	spin_unlock_irqrestore(hba->host->host_lock, flags);
>   
>   	/* poll for max. 1 sec to clear door bell register by h/w */
> diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
> index 8110dcd..43035f8 100644
> --- a/drivers/scsi/ufs/ufshcd.h
> +++ b/drivers/scsi/ufs/ufshcd.h
> @@ -595,6 +595,11 @@ struct ufs_hba {
>   	 */
>   	#define UFSHCD_QUIRK_PRDT_BYTE_GRAN			0x80
>   
> +	/*
> +	 * Cleaer handling for transfer/task request list is just opposite.
> +	 */
Spell check - should be 'Clear'
> +	#define UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR		0x100
> +
>   	unsigned int quirks;	/* Deviations from standard UFSHCI spec. */
>   
>   	/* Device deviations from standard UFS device spec. */
> 

Looks good to me, except the spell-check.

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a 
Linux Foundation Collaborative Project

Re: [PATCH 0/4] Add required changes to ufshcd to support exynos ufs hci

[Martin K. Petersen]

Alim,

> These patches are part of a larger patch series [1] which attempts
> upstreaming EXYNOS UFS driver support. There was not much activities
> after v5 of that series. In between I saw there were other teams in
> Samsung tried upstreaming the same, but that has not really gone
> anywhere.  I have taken this task again and here is another attempt to
> upstream exynos-ufs driver support. I have divided the patches into
> two series, one which adds required infra in the ufshcd core needed by
> exynos-ufs driver and other part will have actual exynos-ufs
> driver. Splitting this has a advantage of less reviewing over head.

Applied to 4.18/scsi-queue. Thank you!

-- 
Martin K. Petersen	Oracle Linux Engineering