From: Chen-Yu Tsai <wens@csie.org>
To: megous@megous.com
Cc: dev <dev@linux-sunxi.org>,
linux-arm-kernel <linux-arm-kernel@lists.infradead.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Russell King <linux@armlinux.org.uk>,
Maxime Ripard <maxime.ripard@free-electrons.com>,
Chen-Yu Tsai <wens@csie.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
open list <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 06/14] ARM: dts: sun8i: Add cpu0 label to sun8i-h3.dtsi
Date: Fri, 24 Jun 2016 11:48:23 +0800 [thread overview]
Message-ID: <CAGb2v66eskVAxdz8VtjBJBCO7VV9WL4bdFDVrPWrSmxk4RASCw@mail.gmail.com> (raw)
In-Reply-To: <20160623192104.18720-7-megous@megous.com>
On Fri, Jun 24, 2016 at 3:20 AM, <megous@megous.com> wrote:
> From: Ondrej Jirman <megous@megous.com>
>
> Add label to the first cpu so that it can be referenced
> from derived dts files.
>
> Signed-off-by: Ondrej Jirman <megous@megous.com>
> ---
> arch/arm/boot/dts/sun8i-h3.dtsi | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> index 9938972..82faefc 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -52,7 +52,7 @@
> #address-cells = <1>;
> #size-cells = <0>;
>
> - cpu@0 {
> + cpu0: cpu@0 {
> compatible = "arm,cortex-a7";
> device_type = "cpu";
> reg = <0>;
Can you also set the cpu clock here? It is part of the SoC
and does not belong in the board DTS files.
Otherwise this one looks good.
ChenYu
> --
> 2.9.0
>
next prev parent reply other threads:[~2016-06-24 3:48 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20160623192104.18720-1-megous@megous.com>
2016-06-23 19:20 ` [PATCH 01/14] ARM: dts: sun8i: Add SID node megous
2016-06-24 2:41 ` Chen-Yu Tsai
2016-06-24 19:58 ` Ondřej Jirman
2016-06-25 1:09 ` [linux-sunxi] " Chen-Yu Tsai
2016-06-23 19:20 ` [PATCH 02/14] ARM: clk: sunxi: Add driver for the H3 THS clock megous
2016-06-23 19:20 ` [PATCH 03/14] thermal: Add support for sun8i THS on Allwinner H3 megous
2016-06-24 3:09 ` Chen-Yu Tsai
2016-06-24 21:50 ` Ondřej Jirman
2016-06-25 0:35 ` Ondřej Jirman
2016-06-25 0:54 ` Chen-Yu Tsai
2016-06-25 0:56 ` Ondřej Jirman
2016-06-23 19:20 ` [PATCH 04/14] dt-bindings: document sun8i_ths megous
2016-06-24 2:46 ` Chen-Yu Tsai
2016-06-23 19:20 ` [PATCH 05/14] ARM: dts: sun8i: Add THS node to the sun8i-h3.dtsi megous
2016-06-23 19:20 ` [PATCH 06/14] ARM: dts: sun8i: Add cpu0 label to sun8i-h3.dtsi megous
2016-06-24 3:48 ` Chen-Yu Tsai [this message]
2016-06-24 22:51 ` Ondřej Jirman
2016-06-25 1:02 ` Chen-Yu Tsai
2016-06-25 7:02 ` Maxime Ripard
2016-06-25 14:50 ` Ondřej Jirman
2016-06-29 20:45 ` Maxime Ripard
2016-06-29 21:11 ` Ondřej Jirman
2016-06-30 11:04 ` [linux-sunxi] " Michal Suchanek
2016-06-30 20:41 ` Maxime Ripard
2016-07-17 14:39 ` Ondřej Jirman
2016-07-25 8:26 ` Maxime Ripard
[not found] ` <e57eb018-ef31-408e-84b2-b329510352d0@googlegroups.com>
2016-07-25 8:51 ` Maxime Ripard
2016-06-23 19:20 ` [PATCH 07/14] regulator: SY8106A regulator driver megous
2016-06-24 3:41 ` Chen-Yu Tsai
2016-06-25 0:11 ` Ondřej Jirman
2016-06-25 1:00 ` Chen-Yu Tsai
2016-06-23 19:20 ` [PATCH 08/14] ARM: dts: sun8i: Add r_twi I2C controller megous
2016-06-23 19:20 ` [PATCH 09/14] ARM: dts: sun8i: Enable r_twi on Orange Pi PC megous
2016-06-23 19:21 ` [PATCH 10/14] ARM: dts: sun8i: Add sy8106a regulator to " megous
2016-06-24 9:14 ` Chen-Yu Tsai
2016-06-23 19:21 ` [PATCH 11/14] ARM: sun8i: clk: Add clk-factor rate application method megous
2016-06-24 2:53 ` [linux-sunxi] " Julian Calaby
2016-06-23 19:21 ` [PATCH 12/14] ARM: dts: sun8i: Setup CPU operating points for Onrage PI PC megous
2016-06-23 19:21 ` [PATCH 13/14] ARM: dts: sun8i: Add gpio-regulator used on Orange Pi One megous
2016-06-24 2:51 ` [linux-sunxi] " Julian Calaby
2016-06-24 22:39 ` Ondřej Jirman
2016-06-24 2:55 ` Julian Calaby
2016-06-23 19:21 ` [PATCH 14/14] ARM: dts: sun8i: Enable DVFS " megous
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAGb2v66eskVAxdz8VtjBJBCO7VV9WL4bdFDVrPWrSmxk4RASCw@mail.gmail.com \
--to=wens@csie.org \
--cc=dev@linux-sunxi.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@free-electrons.com \
--cc=megous@megous.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).