From: Chen-Yu Tsai <wens@csie.org>
To: Jens Kuske <jenskuske@gmail.com>
Cc: "Maxime Ripard" <maxime.ripard@free-electrons.com>,
"Chen-Yu Tsai" <wens@csie.org>,
"Michael Turquette" <mturquette@baylibre.com>,
"Linus Walleij" <linus.walleij@linaro.org>,
"Rob Herring" <robh+dt@kernel.org>,
"Philipp Zabel" <p.zabel@pengutronix.de>,
"Emilio López" <emilio@elopez.com.ar>,
"Vishnu Patekar" <vishnupatekar0510@gmail.com>,
"Hans de Goede" <hdegoede@redhat.com>,
devicetree <devicetree@vger.kernel.org>,
linux-arm-kernel <linux-arm-kernel@lists.infradead.org>,
linux-kernel <linux-kernel@vger.kernel.org>,
linux-sunxi <linux-sunxi@googlegroups.com>
Subject: Re: [PATCH v4 3/6] pinctrl: sunxi: Add H3 PIO controller support
Date: Fri, 30 Oct 2015 16:08:25 +0800 [thread overview]
Message-ID: <CAGb2v66wsCgoxedFY1mvVmQkLoRCRz_yeLaa0F8wG10JYHvXRg@mail.gmail.com> (raw)
In-Reply-To: <1445964626-6484-4-git-send-email-jenskuske@gmail.com>
Hi,
On Wed, Oct 28, 2015 at 12:50 AM, Jens Kuske <jenskuske@gmail.com> wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> ---
> .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
> drivers/pinctrl/sunxi/Kconfig | 4 +
> drivers/pinctrl/sunxi/Makefile | 1 +
> drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c | 516 +++++++++++++++++++++
> 4 files changed, 522 insertions(+)
> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> index b321b26..e6ba602 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> @@ -18,6 +18,7 @@ Required properties:
> "allwinner,sun8i-a23-r-pinctrl"
> "allwinner,sun8i-a33-pinctrl"
> "allwinner,sun8i-a83t-pinctrl"
> + "allwinner,sun8i-h3-pinctrl"
>
> - reg: Should contain the register physical address and length for the
> pin controller.
> diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
> index e68fd95..89ab7f5 100644
> --- a/drivers/pinctrl/sunxi/Kconfig
> +++ b/drivers/pinctrl/sunxi/Kconfig
> @@ -51,6 +51,10 @@ config PINCTRL_SUN8I_A23_R
> depends on RESET_CONTROLLER
> select PINCTRL_SUNXI_COMMON
>
> +config PINCTRL_SUN8I_H3
> + def_bool MACH_SUN8I
> + select PINCTRL_SUNXI_COMMON
> +
> config PINCTRL_SUN9I_A80
> def_bool MACH_SUN9I
> select PINCTRL_SUNXI_COMMON
> diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
> index e080290..6bd818e 100644
> --- a/drivers/pinctrl/sunxi/Makefile
> +++ b/drivers/pinctrl/sunxi/Makefile
> @@ -13,4 +13,5 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23) += pinctrl-sun8i-a23.o
> obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o
> obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o
> obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
> +obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
> obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> new file mode 100644
> index 0000000..98d465d
> --- /dev/null
> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> @@ -0,0 +1,516 @@
> +/*
> + * Allwinner H3 SoCs pinctrl driver.
> + *
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * Based on pinctrl-sun8i-a23.c, which is:
> + * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
> + * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/pinctrl/pinctrl.h>
> +
> +#include "pinctrl-sunxi.h"
> +
> +static const struct sunxi_desc_pin sun8i_h3_pins[] = {
<snip>
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXCK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXCTL/RCDV */
RXDV?
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXERR */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD2L */
Trailing "L" there.
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD1 */
<snip>
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 0)), /* PG_EINT0 */
Datasheet say EINT is function 0x6. Same for all the other pins in group G.
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 1)), /* PG_EINT1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 2)), /* PG_EINT2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 3)), /* PG_EINT3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 4)), /* PG_EINT4 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 5)), /* PG_EINT5 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* TX */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 6)), /* PG_EINT6 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* RX */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 7)), /* PG_EINT7 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 8)), /* PG_EINT8 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 9)), /* PG_EINT9 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* SYNC */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 10)), /* PG_EINT10 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* CLK */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 11)), /* PG_EINT11 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* DOUT */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 12)), /* PG_EINT12 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* DIN */
> + SUNXI_FUNCTION_IRQ_BANK(0x4, 1, 13)), /* PG_EINT13 */
> +};
> +
> +static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
> + .pins = sun8i_h3_pins,
> + .npins = ARRAY_SIZE(sun8i_h3_pins),
> + .irq_banks = 2,
> +};
> +
> +static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
> +{
> + return sunxi_pinctrl_init(pdev,
> + &sun8i_h3_pinctrl_data);
> +}
> +
> +static const struct of_device_id sun8i_h3_pinctrl_match[] = {
> + { .compatible = "allwinner,sun8i-h3-pinctrl", },
> + {}
> +};
> +
> +static struct platform_driver sun8i_h3_pinctrl_driver = {
> + .probe = sun8i_h3_pinctrl_probe,
> + .driver = {
> + .name = "sun8i-h3-pinctrl",
> + .of_match_table = sun8i_h3_pinctrl_match,
> + },
> +};
> +builtin_platform_driver(sun8i_h3_pinctrl_driver);
> --
> 2.6.2
>
The rest looks good. Thanks!
Regards
ChenYu
next prev parent reply other threads:[~2015-10-30 8:09 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-10-27 16:50 [PATCH v4 0/6] ARM: sunxi: Introduce Allwinner H3 support Jens Kuske
2015-10-27 16:50 ` [PATCH v4 1/6] clk: sunxi: Let divs clocks read the base factor clock name from devicetree Jens Kuske
2015-10-30 7:46 ` Chen-Yu Tsai
2015-11-01 13:11 ` Jens Kuske
2015-10-27 16:50 ` [PATCH v4 2/6] clk: sunxi: Add H3 clocks support Jens Kuske
2015-10-27 23:12 ` [linux-sunxi] " Julian Calaby
2015-11-04 16:23 ` Maxime Ripard
2015-11-04 22:17 ` Julian Calaby
2015-10-30 8:28 ` Arnd Bergmann
2015-11-01 13:40 ` Jens Kuske
2015-11-04 16:24 ` Maxime Ripard
2015-10-27 16:50 ` [PATCH v4 3/6] pinctrl: sunxi: Add H3 PIO controller support Jens Kuske
2015-10-30 8:08 ` Chen-Yu Tsai [this message]
2015-11-01 13:17 ` Jens Kuske
2015-11-01 15:25 ` [linux-sunxi] " Chen-Yu Tsai
2015-10-27 16:50 ` [PATCH v4 4/6] reset: sunxi: Add Allwinner H3 bus resets Jens Kuske
2015-10-28 11:42 ` Philipp Zabel
2015-10-30 8:27 ` Arnd Bergmann
2015-11-01 13:21 ` Jens Kuske
2015-11-04 16:30 ` Maxime Ripard
2015-11-05 6:47 ` Jean-Francois Moine
2015-11-23 7:41 ` [linux-sunxi] " Chen-Yu Tsai
2015-11-23 11:29 ` Maxime Ripard
2015-10-27 16:50 ` [PATCH v4 5/6] ARM: dts: sunxi: Add Allwinner H3 DTSI Jens Kuske
2015-10-30 7:33 ` Chen-Yu Tsai
2015-11-01 9:46 ` Maxime Ripard
2015-11-01 13:33 ` Jens Kuske
2015-11-23 8:57 ` Maxime Ripard
2015-11-23 10:50 ` [linux-sunxi] " Hans de Goede
2015-11-23 16:25 ` Jens Kuske
2015-11-23 16:48 ` Chen-Yu Tsai
2015-10-30 10:34 ` Jean-Francois Moine
2015-11-01 9:48 ` Maxime Ripard
2015-11-01 9:52 ` Maxime Ripard
2015-10-27 16:50 ` [PATCH v4 6/6] ARM: dts: sun8i: Add Orange Pi Plus support Jens Kuske
2015-10-27 18:04 ` [PATCH v4 0/6] ARM: sunxi: Introduce Allwinner H3 support Jean-Francois Moine
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAGb2v66wsCgoxedFY1mvVmQkLoRCRz_yeLaa0F8wG10JYHvXRg@mail.gmail.com \
--to=wens@csie.org \
--cc=devicetree@vger.kernel.org \
--cc=emilio@elopez.com.ar \
--cc=hdegoede@redhat.com \
--cc=jenskuske@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=maxime.ripard@free-electrons.com \
--cc=mturquette@baylibre.com \
--cc=p.zabel@pengutronix.de \
--cc=robh+dt@kernel.org \
--cc=vishnupatekar0510@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).