* [PATCH] arm64: allwinner: h6: Add OrangePi One Plus initial support
@ 2018-07-28 18:26 Jagan Teki
2018-07-30 9:00 ` Maxime Ripard
0 siblings, 1 reply; 8+ messages in thread
From: Jagan Teki @ 2018-07-28 18:26 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Icenowy Zheng
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-sunxi, Jagan Teki
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-h6-orangepi-one-plus.dts | 150 ++++++++++++++++++
2 files changed, 151 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 9ffa7a038791..c38f326e7fec 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -15,4 +15,5 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
new file mode 100644
index 000000000000..0612c19cd994
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2018 Amarula Solutions
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "OrangePi One Plus";
+ compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_cldo1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp805: pmic@36 {
+ compatible = "x-powers,axp805", "x-powers,axp806";
+ reg = <0x36>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ x-powers,self-working-mode;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ac200";
+ };
+
+ reg_aldo3: aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc25-dram";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-bias-pll";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-efuse-pcie-hdmi-io";
+ };
+
+ reg_bldo3: bldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dcxoio";
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ reg_cldo1: cldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-1";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <960000>;
+ regulator-max-microvolt = <960000>;
+ regulator-name = "vdd-sys";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
--
2.17.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: allwinner: h6: Add OrangePi One Plus initial support
2018-07-28 18:26 [PATCH] arm64: allwinner: h6: Add OrangePi One Plus initial support Jagan Teki
@ 2018-07-30 9:00 ` Maxime Ripard
2018-07-30 9:17 ` Chen-Yu Tsai
0 siblings, 1 reply; 8+ messages in thread
From: Maxime Ripard @ 2018-07-30 9:00 UTC (permalink / raw)
To: Jagan Teki
Cc: Chen-Yu Tsai, Icenowy Zheng, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 5421 bytes --]
Hi,
On Sat, Jul 28, 2018 at 11:56:15PM +0530, Jagan Teki wrote:
> OrangePi One Plus is Allwinner H6 based open-source SBC,
> which support:
> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> - GPU Mali-T720
> - 1GB LPDDR3 RAM
> - AXP805 PMIC
> - 1Gbps GMAC via RTL8211
> - USB 2.0 Host, OTG
> - HDMI port
> - 5V/2A DC power supply
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../allwinner/sun50i-h6-orangepi-one-plus.dts | 150 ++++++++++++++++++
> 2 files changed, 151 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 9ffa7a038791..c38f326e7fec 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -15,4 +15,5 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
> new file mode 100644
> index 000000000000..0612c19cd994
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
> @@ -0,0 +1,150 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2018 Amarula Solutions
> + * Author: Jagan Teki <jagan@amarulasolutions.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h6.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "OrangePi One Plus";
> + compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;
> + vmmc-supply = <®_cldo1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&r_i2c {
> + status = "okay";
> +
> + axp805: pmic@36 {
> + compatible = "x-powers,axp805", "x-powers,axp806";
> + reg = <0x36>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + x-powers,self-working-mode;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-ac200";
> + };
> +
> + reg_aldo3: aldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc25-dram";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-bias-pll";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-efuse-pcie-hdmi-io";
> + };
> +
> + reg_bldo3: bldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-dcxoio";
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + reg_cldo1: cldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3";
> + };
> +
> + reg_cldo2: cldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-1";
> + };
> +
> + reg_cldo3: cldo3 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-2";
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <960000>;
> + regulator-max-microvolt = <960000>;
> + regulator-name = "vdd-sys";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vcc-dram";
> + };
> +
> + sw {
> + /* unused */
> + };
Can't we have a DTSI for this PMIC too?
It looks good otherwise, thanks!
Maxime
--
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: allwinner: h6: Add OrangePi One Plus initial support
2018-07-30 9:00 ` Maxime Ripard
@ 2018-07-30 9:17 ` Chen-Yu Tsai
2018-07-31 13:41 ` Jagan Teki
0 siblings, 1 reply; 8+ messages in thread
From: Chen-Yu Tsai @ 2018-07-30 9:17 UTC (permalink / raw)
To: Maxime Ripard
Cc: Jagan Teki, Icenowy Zheng, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
On Mon, Jul 30, 2018 at 5:00 PM, Maxime Ripard
<maxime.ripard@bootlin.com> wrote:
> Hi,
>
> On Sat, Jul 28, 2018 at 11:56:15PM +0530, Jagan Teki wrote:
>> OrangePi One Plus is Allwinner H6 based open-source SBC,
>> which support:
>> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
>> - GPU Mali-T720
>> - 1GB LPDDR3 RAM
>> - AXP805 PMIC
>> - 1Gbps GMAC via RTL8211
>> - USB 2.0 Host, OTG
>> - HDMI port
>> - 5V/2A DC power supply
>>
>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>> ---
>> arch/arm64/boot/dts/allwinner/Makefile | 1 +
>> .../allwinner/sun50i-h6-orangepi-one-plus.dts | 150 ++++++++++++++++++
>> 2 files changed, 151 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>>
>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
>> index 9ffa7a038791..c38f326e7fec 100644
>> --- a/arch/arm64/boot/dts/allwinner/Makefile
>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
>> @@ -15,4 +15,5 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>> new file mode 100644
>> index 000000000000..0612c19cd994
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>> @@ -0,0 +1,150 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
>> +/*
>> + * Copyright (C) 2018 Amarula Solutions
>> + * Author: Jagan Teki <jagan@amarulasolutions.com>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "sun50i-h6.dtsi"
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +
>> +/ {
>> + model = "OrangePi One Plus";
>> + compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
>> +
>> + aliases {
>> + serial0 = &uart0;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial0:115200n8";
>> + };
>> +};
>> +
>> +&mmc0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc0_pins>;
>> + vmmc-supply = <®_cldo1>;
>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
>> + bus-width = <4>;
>> + status = "okay";
>> +};
>> +
>> +&r_i2c {
>> + status = "okay";
>> +
>> + axp805: pmic@36 {
>> + compatible = "x-powers,axp805", "x-powers,axp806";
>> + reg = <0x36>;
>> + interrupt-parent = <&r_intc>;
>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> + interrupt-controller;
>> + #interrupt-cells = <1>;
>> + x-powers,self-working-mode;
>> +
>> + regulators {
>> + reg_aldo1: aldo1 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc-pl";
>> + };
>> +
>> + reg_aldo2: aldo2 {
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc-ac200";
>> + };
>> +
>> + reg_aldo3: aldo3 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc25-dram";
>> + };
>> +
>> + reg_bldo1: bldo1 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc-bias-pll";
>> + };
>> +
>> + reg_bldo2: bldo2 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc-efuse-pcie-hdmi-io";
>> + };
>> +
>> + reg_bldo3: bldo3 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-name = "vcc-dcxoio";
>> + };
>> +
>> + bldo4 {
>> + /* unused */
>> + };
>> +
>> + reg_cldo1: cldo1 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc-3v3";
>> + };
>> +
>> + reg_cldo2: cldo2 {
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc-wifi-1";
>> + };
>> +
>> + reg_cldo3: cldo3 {
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-name = "vcc-wifi-2";
>> + };
>> +
>> + reg_dcdca: dcdca {
>> + regulator-always-on;
>> + regulator-min-microvolt = <810000>;
>> + regulator-max-microvolt = <1080000>;
>> + regulator-name = "vdd-cpu";
>> + };
>> +
>> + reg_dcdcc: dcdcc {
>> + regulator-min-microvolt = <810000>;
>> + regulator-max-microvolt = <1080000>;
>> + regulator-name = "vdd-gpu";
>> + };
>> +
>> + reg_dcdcd: dcdcd {
>> + regulator-always-on;
>> + regulator-min-microvolt = <960000>;
>> + regulator-max-microvolt = <960000>;
>> + regulator-name = "vdd-sys";
>> + };
>> +
>> + reg_dcdce: dcdce {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + regulator-name = "vcc-dram";
>> + };
>> +
>> + sw {
>> + /* unused */
>> + };
>
> Can't we have a DTSI for this PMIC too?
Back when we started adding the regulators, Mark wasn't too happy with
all the placeholders we put in the dtsi. I think we got away with it
because we had other things in there as well. That's not true for this
particular PMIC.
ChenYu
> It looks good otherwise, thanks!
> Maxime
>
> --
> Maxime Ripard, Bootlin (formerly Free Electrons)
> Embedded Linux and Kernel engineering
> https://bootlin.com
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: allwinner: h6: Add OrangePi One Plus initial support
2018-07-30 9:17 ` Chen-Yu Tsai
@ 2018-07-31 13:41 ` Jagan Teki
2018-07-31 13:42 ` Chen-Yu Tsai
0 siblings, 1 reply; 8+ messages in thread
From: Jagan Teki @ 2018-07-31 13:41 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Maxime Ripard, Icenowy Zheng, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
On Mon, Jul 30, 2018 at 2:47 PM, Chen-Yu Tsai <wens@csie.org> wrote:
> On Mon, Jul 30, 2018 at 5:00 PM, Maxime Ripard
> <maxime.ripard@bootlin.com> wrote:
>> Hi,
>>
>> On Sat, Jul 28, 2018 at 11:56:15PM +0530, Jagan Teki wrote:
>>> OrangePi One Plus is Allwinner H6 based open-source SBC,
>>> which support:
>>> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
>>> - GPU Mali-T720
>>> - 1GB LPDDR3 RAM
>>> - AXP805 PMIC
>>> - 1Gbps GMAC via RTL8211
>>> - USB 2.0 Host, OTG
>>> - HDMI port
>>> - 5V/2A DC power supply
>>>
>>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>>> ---
>>> arch/arm64/boot/dts/allwinner/Makefile | 1 +
>>> .../allwinner/sun50i-h6-orangepi-one-plus.dts | 150 ++++++++++++++++++
>>> 2 files changed, 151 insertions(+)
>>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>>>
>>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
>>> index 9ffa7a038791..c38f326e7fec 100644
>>> --- a/arch/arm64/boot/dts/allwinner/Makefile
>>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
>>> @@ -15,4 +15,5 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
>>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>>> new file mode 100644
>>> index 000000000000..0612c19cd994
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>>> @@ -0,0 +1,150 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
>>> +/*
>>> + * Copyright (C) 2018 Amarula Solutions
>>> + * Author: Jagan Teki <jagan@amarulasolutions.com>
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "sun50i-h6.dtsi"
>>> +
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +
>>> +/ {
>>> + model = "OrangePi One Plus";
>>> + compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
>>> +
>>> + aliases {
>>> + serial0 = &uart0;
>>> + };
>>> +
>>> + chosen {
>>> + stdout-path = "serial0:115200n8";
>>> + };
>>> +};
>>> +
>>> +&mmc0 {
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&mmc0_pins>;
>>> + vmmc-supply = <®_cldo1>;
>>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
>>> + bus-width = <4>;
>>> + status = "okay";
>>> +};
>>> +
>>> +&r_i2c {
>>> + status = "okay";
>>> +
>>> + axp805: pmic@36 {
>>> + compatible = "x-powers,axp805", "x-powers,axp806";
>>> + reg = <0x36>;
>>> + interrupt-parent = <&r_intc>;
>>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>>> + interrupt-controller;
>>> + #interrupt-cells = <1>;
>>> + x-powers,self-working-mode;
>>> +
>>> + regulators {
>>> + reg_aldo1: aldo1 {
>>> + regulator-always-on;
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-name = "vcc-pl";
>>> + };
>>> +
>>> + reg_aldo2: aldo2 {
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-name = "vcc-ac200";
>>> + };
>>> +
>>> + reg_aldo3: aldo3 {
>>> + regulator-always-on;
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-name = "vcc25-dram";
>>> + };
>>> +
>>> + reg_bldo1: bldo1 {
>>> + regulator-always-on;
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1800000>;
>>> + regulator-name = "vcc-bias-pll";
>>> + };
>>> +
>>> + reg_bldo2: bldo2 {
>>> + regulator-always-on;
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1800000>;
>>> + regulator-name = "vcc-efuse-pcie-hdmi-io";
>>> + };
>>> +
>>> + reg_bldo3: bldo3 {
>>> + regulator-always-on;
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1800000>;
>>> + regulator-name = "vcc-dcxoio";
>>> + };
>>> +
>>> + bldo4 {
>>> + /* unused */
>>> + };
>>> +
>>> + reg_cldo1: cldo1 {
>>> + regulator-always-on;
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-name = "vcc-3v3";
>>> + };
>>> +
>>> + reg_cldo2: cldo2 {
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-name = "vcc-wifi-1";
>>> + };
>>> +
>>> + reg_cldo3: cldo3 {
>>> + regulator-min-microvolt = <3300000>;
>>> + regulator-max-microvolt = <3300000>;
>>> + regulator-name = "vcc-wifi-2";
>>> + };
>>> +
>>> + reg_dcdca: dcdca {
>>> + regulator-always-on;
>>> + regulator-min-microvolt = <810000>;
>>> + regulator-max-microvolt = <1080000>;
>>> + regulator-name = "vdd-cpu";
>>> + };
>>> +
>>> + reg_dcdcc: dcdcc {
>>> + regulator-min-microvolt = <810000>;
>>> + regulator-max-microvolt = <1080000>;
>>> + regulator-name = "vdd-gpu";
>>> + };
>>> +
>>> + reg_dcdcd: dcdcd {
>>> + regulator-always-on;
>>> + regulator-min-microvolt = <960000>;
>>> + regulator-max-microvolt = <960000>;
>>> + regulator-name = "vdd-sys";
>>> + };
>>> +
>>> + reg_dcdce: dcdce {
>>> + regulator-always-on;
>>> + regulator-min-microvolt = <1200000>;
>>> + regulator-max-microvolt = <1200000>;
>>> + regulator-name = "vcc-dram";
>>> + };
>>> +
>>> + sw {
>>> + /* unused */
>>> + };
>>
>> Can't we have a DTSI for this PMIC too?
>
> Back when we started adding the regulators, Mark wasn't too happy with
> all the placeholders we put in the dtsi. I think we got away with it
> because we had other things in there as well. That's not true for this
> particular PMIC.
So we need separate dtsi for this PMIC as well?
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: allwinner: h6: Add OrangePi One Plus initial support
2018-07-31 13:41 ` Jagan Teki
@ 2018-07-31 13:42 ` Chen-Yu Tsai
2018-09-03 5:35 ` Chen-Yu Tsai
0 siblings, 1 reply; 8+ messages in thread
From: Chen-Yu Tsai @ 2018-07-31 13:42 UTC (permalink / raw)
To: Jagan Teki
Cc: Maxime Ripard, Icenowy Zheng, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
On Tue, Jul 31, 2018 at 9:41 PM, Jagan Teki <jagan@amarulasolutions.com> wrote:
> On Mon, Jul 30, 2018 at 2:47 PM, Chen-Yu Tsai <wens@csie.org> wrote:
>> On Mon, Jul 30, 2018 at 5:00 PM, Maxime Ripard
>> <maxime.ripard@bootlin.com> wrote:
>>> Hi,
>>>
>>> On Sat, Jul 28, 2018 at 11:56:15PM +0530, Jagan Teki wrote:
>>>> OrangePi One Plus is Allwinner H6 based open-source SBC,
>>>> which support:
>>>> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
>>>> - GPU Mali-T720
>>>> - 1GB LPDDR3 RAM
>>>> - AXP805 PMIC
>>>> - 1Gbps GMAC via RTL8211
>>>> - USB 2.0 Host, OTG
>>>> - HDMI port
>>>> - 5V/2A DC power supply
>>>>
>>>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>>>> ---
>>>> arch/arm64/boot/dts/allwinner/Makefile | 1 +
>>>> .../allwinner/sun50i-h6-orangepi-one-plus.dts | 150 ++++++++++++++++++
>>>> 2 files changed, 151 insertions(+)
>>>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>>>>
>>>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
>>>> index 9ffa7a038791..c38f326e7fec 100644
>>>> --- a/arch/arm64/boot/dts/allwinner/Makefile
>>>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
>>>> @@ -15,4 +15,5 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
>>>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
>>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>>>> new file mode 100644
>>>> index 000000000000..0612c19cd994
>>>> --- /dev/null
>>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>>>> @@ -0,0 +1,150 @@
>>>> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
>>>> +/*
>>>> + * Copyright (C) 2018 Amarula Solutions
>>>> + * Author: Jagan Teki <jagan@amarulasolutions.com>
>>>> + */
>>>> +
>>>> +/dts-v1/;
>>>> +
>>>> +#include "sun50i-h6.dtsi"
>>>> +
>>>> +#include <dt-bindings/gpio/gpio.h>
>>>> +
>>>> +/ {
>>>> + model = "OrangePi One Plus";
>>>> + compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
>>>> +
>>>> + aliases {
>>>> + serial0 = &uart0;
>>>> + };
>>>> +
>>>> + chosen {
>>>> + stdout-path = "serial0:115200n8";
>>>> + };
>>>> +};
>>>> +
>>>> +&mmc0 {
>>>> + pinctrl-names = "default";
>>>> + pinctrl-0 = <&mmc0_pins>;
>>>> + vmmc-supply = <®_cldo1>;
>>>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
>>>> + bus-width = <4>;
>>>> + status = "okay";
>>>> +};
>>>> +
>>>> +&r_i2c {
>>>> + status = "okay";
>>>> +
>>>> + axp805: pmic@36 {
>>>> + compatible = "x-powers,axp805", "x-powers,axp806";
>>>> + reg = <0x36>;
>>>> + interrupt-parent = <&r_intc>;
>>>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>>>> + interrupt-controller;
>>>> + #interrupt-cells = <1>;
>>>> + x-powers,self-working-mode;
>>>> +
>>>> + regulators {
>>>> + reg_aldo1: aldo1 {
>>>> + regulator-always-on;
>>>> + regulator-min-microvolt = <3300000>;
>>>> + regulator-max-microvolt = <3300000>;
>>>> + regulator-name = "vcc-pl";
>>>> + };
>>>> +
>>>> + reg_aldo2: aldo2 {
>>>> + regulator-min-microvolt = <3300000>;
>>>> + regulator-max-microvolt = <3300000>;
>>>> + regulator-name = "vcc-ac200";
>>>> + };
>>>> +
>>>> + reg_aldo3: aldo3 {
>>>> + regulator-always-on;
>>>> + regulator-min-microvolt = <3300000>;
>>>> + regulator-max-microvolt = <3300000>;
>>>> + regulator-name = "vcc25-dram";
>>>> + };
>>>> +
>>>> + reg_bldo1: bldo1 {
>>>> + regulator-always-on;
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <1800000>;
>>>> + regulator-name = "vcc-bias-pll";
>>>> + };
>>>> +
>>>> + reg_bldo2: bldo2 {
>>>> + regulator-always-on;
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <1800000>;
>>>> + regulator-name = "vcc-efuse-pcie-hdmi-io";
>>>> + };
>>>> +
>>>> + reg_bldo3: bldo3 {
>>>> + regulator-always-on;
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <1800000>;
>>>> + regulator-name = "vcc-dcxoio";
>>>> + };
>>>> +
>>>> + bldo4 {
>>>> + /* unused */
>>>> + };
>>>> +
>>>> + reg_cldo1: cldo1 {
>>>> + regulator-always-on;
>>>> + regulator-min-microvolt = <3300000>;
>>>> + regulator-max-microvolt = <3300000>;
>>>> + regulator-name = "vcc-3v3";
>>>> + };
>>>> +
>>>> + reg_cldo2: cldo2 {
>>>> + regulator-min-microvolt = <3300000>;
>>>> + regulator-max-microvolt = <3300000>;
>>>> + regulator-name = "vcc-wifi-1";
>>>> + };
>>>> +
>>>> + reg_cldo3: cldo3 {
>>>> + regulator-min-microvolt = <3300000>;
>>>> + regulator-max-microvolt = <3300000>;
>>>> + regulator-name = "vcc-wifi-2";
>>>> + };
>>>> +
>>>> + reg_dcdca: dcdca {
>>>> + regulator-always-on;
>>>> + regulator-min-microvolt = <810000>;
>>>> + regulator-max-microvolt = <1080000>;
>>>> + regulator-name = "vdd-cpu";
>>>> + };
>>>> +
>>>> + reg_dcdcc: dcdcc {
>>>> + regulator-min-microvolt = <810000>;
>>>> + regulator-max-microvolt = <1080000>;
>>>> + regulator-name = "vdd-gpu";
>>>> + };
>>>> +
>>>> + reg_dcdcd: dcdcd {
>>>> + regulator-always-on;
>>>> + regulator-min-microvolt = <960000>;
>>>> + regulator-max-microvolt = <960000>;
>>>> + regulator-name = "vdd-sys";
>>>> + };
>>>> +
>>>> + reg_dcdce: dcdce {
>>>> + regulator-always-on;
>>>> + regulator-min-microvolt = <1200000>;
>>>> + regulator-max-microvolt = <1200000>;
>>>> + regulator-name = "vcc-dram";
>>>> + };
>>>> +
>>>> + sw {
>>>> + /* unused */
>>>> + };
>>>
>>> Can't we have a DTSI for this PMIC too?
>>
>> Back when we started adding the regulators, Mark wasn't too happy with
>> all the placeholders we put in the dtsi. I think we got away with it
>> because we had other things in there as well. That's not true for this
>> particular PMIC.
>
> So we need separate dtsi for this PMIC as well?
I don't think we do. We don't gain much.
ChenYu
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] arm64: allwinner: h6: Add OrangePi One Plus initial support
2018-07-31 13:42 ` Chen-Yu Tsai
@ 2018-09-03 5:35 ` Chen-Yu Tsai
2018-09-04 14:30 ` [linux-sunxi] " Jagan Teki
0 siblings, 1 reply; 8+ messages in thread
From: Chen-Yu Tsai @ 2018-09-03 5:35 UTC (permalink / raw)
To: Jagan Teki
Cc: Maxime Ripard, Icenowy Zheng, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
On Tue, Jul 31, 2018 at 9:42 PM Chen-Yu Tsai <wens@csie.org> wrote:
>
> On Tue, Jul 31, 2018 at 9:41 PM, Jagan Teki <jagan@amarulasolutions.com> wrote:
> > On Mon, Jul 30, 2018 at 2:47 PM, Chen-Yu Tsai <wens@csie.org> wrote:
> >> On Mon, Jul 30, 2018 at 5:00 PM, Maxime Ripard
> >> <maxime.ripard@bootlin.com> wrote:
> >>> Hi,
> >>>
> >>> On Sat, Jul 28, 2018 at 11:56:15PM +0530, Jagan Teki wrote:
> >>>> OrangePi One Plus is Allwinner H6 based open-source SBC,
> >>>> which support:
> >>>> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> >>>> - GPU Mali-T720
> >>>> - 1GB LPDDR3 RAM
> >>>> - AXP805 PMIC
> >>>> - 1Gbps GMAC via RTL8211
> >>>> - USB 2.0 Host, OTG
> >>>> - HDMI port
> >>>> - 5V/2A DC power supply
> >>>>
> >>>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> >>>> ---
> >>>> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> >>>> .../allwinner/sun50i-h6-orangepi-one-plus.dts | 150 ++++++++++++++++++
> >>>> 2 files changed, 151 insertions(+)
> >>>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
> >>>>
> >>>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> >>>> index 9ffa7a038791..c38f326e7fec 100644
> >>>> --- a/arch/arm64/boot/dts/allwinner/Makefile
> >>>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> >>>> @@ -15,4 +15,5 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
> >>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
> >>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
> >>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
> >>>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> >>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> >>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
> >>>> new file mode 100644
> >>>> index 000000000000..0612c19cd994
> >>>> --- /dev/null
> >>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
> >>>> @@ -0,0 +1,150 @@
> >>>> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> >>>> +/*
> >>>> + * Copyright (C) 2018 Amarula Solutions
> >>>> + * Author: Jagan Teki <jagan@amarulasolutions.com>
> >>>> + */
> >>>> +
> >>>> +/dts-v1/;
> >>>> +
> >>>> +#include "sun50i-h6.dtsi"
> >>>> +
> >>>> +#include <dt-bindings/gpio/gpio.h>
> >>>> +
> >>>> +/ {
> >>>> + model = "OrangePi One Plus";
> >>>> + compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
> >>>> +
> >>>> + aliases {
> >>>> + serial0 = &uart0;
> >>>> + };
> >>>> +
> >>>> + chosen {
> >>>> + stdout-path = "serial0:115200n8";
> >>>> + };
> >>>> +};
> >>>> +
> >>>> +&mmc0 {
> >>>> + pinctrl-names = "default";
> >>>> + pinctrl-0 = <&mmc0_pins>;
> >>>> + vmmc-supply = <®_cldo1>;
> >>>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> >>>> + bus-width = <4>;
> >>>> + status = "okay";
> >>>> +};
> >>>> +
> >>>> +&r_i2c {
> >>>> + status = "okay";
> >>>> +
> >>>> + axp805: pmic@36 {
> >>>> + compatible = "x-powers,axp805", "x-powers,axp806";
> >>>> + reg = <0x36>;
> >>>> + interrupt-parent = <&r_intc>;
> >>>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> >>>> + interrupt-controller;
> >>>> + #interrupt-cells = <1>;
> >>>> + x-powers,self-working-mode;
> >>>> +
> >>>> + regulators {
> >>>> + reg_aldo1: aldo1 {
> >>>> + regulator-always-on;
> >>>> + regulator-min-microvolt = <3300000>;
> >>>> + regulator-max-microvolt = <3300000>;
> >>>> + regulator-name = "vcc-pl";
> >>>> + };
> >>>> +
> >>>> + reg_aldo2: aldo2 {
> >>>> + regulator-min-microvolt = <3300000>;
> >>>> + regulator-max-microvolt = <3300000>;
> >>>> + regulator-name = "vcc-ac200";
> >>>> + };
> >>>> +
> >>>> + reg_aldo3: aldo3 {
> >>>> + regulator-always-on;
> >>>> + regulator-min-microvolt = <3300000>;
> >>>> + regulator-max-microvolt = <3300000>;
> >>>> + regulator-name = "vcc25-dram";
> >>>> + };
> >>>> +
> >>>> + reg_bldo1: bldo1 {
> >>>> + regulator-always-on;
> >>>> + regulator-min-microvolt = <1800000>;
> >>>> + regulator-max-microvolt = <1800000>;
> >>>> + regulator-name = "vcc-bias-pll";
> >>>> + };
> >>>> +
> >>>> + reg_bldo2: bldo2 {
> >>>> + regulator-always-on;
> >>>> + regulator-min-microvolt = <1800000>;
> >>>> + regulator-max-microvolt = <1800000>;
> >>>> + regulator-name = "vcc-efuse-pcie-hdmi-io";
> >>>> + };
> >>>> +
> >>>> + reg_bldo3: bldo3 {
> >>>> + regulator-always-on;
> >>>> + regulator-min-microvolt = <1800000>;
> >>>> + regulator-max-microvolt = <1800000>;
> >>>> + regulator-name = "vcc-dcxoio";
> >>>> + };
> >>>> +
> >>>> + bldo4 {
> >>>> + /* unused */
> >>>> + };
> >>>> +
> >>>> + reg_cldo1: cldo1 {
> >>>> + regulator-always-on;
> >>>> + regulator-min-microvolt = <3300000>;
> >>>> + regulator-max-microvolt = <3300000>;
> >>>> + regulator-name = "vcc-3v3";
> >>>> + };
> >>>> +
> >>>> + reg_cldo2: cldo2 {
> >>>> + regulator-min-microvolt = <3300000>;
> >>>> + regulator-max-microvolt = <3300000>;
> >>>> + regulator-name = "vcc-wifi-1";
> >>>> + };
> >>>> +
> >>>> + reg_cldo3: cldo3 {
> >>>> + regulator-min-microvolt = <3300000>;
> >>>> + regulator-max-microvolt = <3300000>;
> >>>> + regulator-name = "vcc-wifi-2";
> >>>> + };
> >>>> +
> >>>> + reg_dcdca: dcdca {
> >>>> + regulator-always-on;
> >>>> + regulator-min-microvolt = <810000>;
> >>>> + regulator-max-microvolt = <1080000>;
> >>>> + regulator-name = "vdd-cpu";
> >>>> + };
> >>>> +
> >>>> + reg_dcdcc: dcdcc {
> >>>> + regulator-min-microvolt = <810000>;
> >>>> + regulator-max-microvolt = <1080000>;
> >>>> + regulator-name = "vdd-gpu";
> >>>> + };
> >>>> +
> >>>> + reg_dcdcd: dcdcd {
> >>>> + regulator-always-on;
> >>>> + regulator-min-microvolt = <960000>;
> >>>> + regulator-max-microvolt = <960000>;
> >>>> + regulator-name = "vdd-sys";
> >>>> + };
> >>>> +
> >>>> + reg_dcdce: dcdce {
> >>>> + regulator-always-on;
> >>>> + regulator-min-microvolt = <1200000>;
> >>>> + regulator-max-microvolt = <1200000>;
> >>>> + regulator-name = "vcc-dram";
> >>>> + };
> >>>> +
> >>>> + sw {
> >>>> + /* unused */
> >>>> + };
> >>>
> >>> Can't we have a DTSI for this PMIC too?
> >>
> >> Back when we started adding the regulators, Mark wasn't too happy with
> >> all the placeholders we put in the dtsi. I think we got away with it
> >> because we had other things in there as well. That's not true for this
> >> particular PMIC.
> >
> > So we need separate dtsi for this PMIC as well?
>
> I don't think we do. We don't gain much.
Merged with Maxime's ack, and the subject prefix fixed.
Also squashed in the Ethernet patch for this board.
ChenYu
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [linux-sunxi] Re: [PATCH] arm64: allwinner: h6: Add OrangePi One Plus initial support
2018-09-03 5:35 ` Chen-Yu Tsai
@ 2018-09-04 14:30 ` Jagan Teki
2018-09-04 15:10 ` Chen-Yu Tsai
0 siblings, 1 reply; 8+ messages in thread
From: Jagan Teki @ 2018-09-04 14:30 UTC (permalink / raw)
To: wens, Jagan Teki
Cc: Maxime Ripard, Icenowy Zheng, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
On Monday 03 September 2018 11:05 AM, Chen-Yu Tsai wrote:
> On Tue, Jul 31, 2018 at 9:42 PM Chen-Yu Tsai <wens@csie.org> wrote:
>>
>> On Tue, Jul 31, 2018 at 9:41 PM, Jagan Teki <jagan@amarulasolutions.com> wrote:
>>> On Mon, Jul 30, 2018 at 2:47 PM, Chen-Yu Tsai <wens@csie.org> wrote:
>>>> On Mon, Jul 30, 2018 at 5:00 PM, Maxime Ripard
>>>> <maxime.ripard@bootlin.com> wrote:
>>>>> Hi,
>>>>>
>>>>> On Sat, Jul 28, 2018 at 11:56:15PM +0530, Jagan Teki wrote:
>>>>>> OrangePi One Plus is Allwinner H6 based open-source SBC,
>>>>>> which support:
>>>>>> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
>>>>>> - GPU Mali-T720
>>>>>> - 1GB LPDDR3 RAM
>>>>>> - AXP805 PMIC
>>>>>> - 1Gbps GMAC via RTL8211
>>>>>> - USB 2.0 Host, OTG
>>>>>> - HDMI port
>>>>>> - 5V/2A DC power supply
>>>>>>
>>>>>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>>>>>> ---
>>>>>> arch/arm64/boot/dts/allwinner/Makefile | 1 +
>>>>>> .../allwinner/sun50i-h6-orangepi-one-plus.dts | 150 ++++++++++++++++++
>>>>>> 2 files changed, 151 insertions(+)
>>>>>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>>>>>>
>>>>>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
>>>>>> index 9ffa7a038791..c38f326e7fec 100644
>>>>>> --- a/arch/arm64/boot/dts/allwinner/Makefile
>>>>>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
>>>>>> @@ -15,4 +15,5 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
>>>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
>>>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
>>>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
>>>>>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
>>>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
>>>>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>>>>>> new file mode 100644
>>>>>> index 000000000000..0612c19cd994
>>>>>> --- /dev/null
>>>>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
>>>>>> @@ -0,0 +1,150 @@
>>>>>> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
>>>>>> +/*
>>>>>> + * Copyright (C) 2018 Amarula Solutions
>>>>>> + * Author: Jagan Teki <jagan@amarulasolutions.com>
>>>>>> + */
>>>>>> +
>>>>>> +/dts-v1/;
>>>>>> +
>>>>>> +#include "sun50i-h6.dtsi"
>>>>>> +
>>>>>> +#include <dt-bindings/gpio/gpio.h>
>>>>>> +
>>>>>> +/ {
>>>>>> + model = "OrangePi One Plus";
>>>>>> + compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
>>>>>> +
>>>>>> + aliases {
>>>>>> + serial0 = &uart0;
>>>>>> + };
>>>>>> +
>>>>>> + chosen {
>>>>>> + stdout-path = "serial0:115200n8";
>>>>>> + };
>>>>>> +};
>>>>>> +
>>>>>> +&mmc0 {
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&mmc0_pins>;
>>>>>> + vmmc-supply = <®_cldo1>;
>>>>>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
>>>>>> + bus-width = <4>;
>>>>>> + status = "okay";
>>>>>> +};
>>>>>> +
>>>>>> +&r_i2c {
>>>>>> + status = "okay";
>>>>>> +
>>>>>> + axp805: pmic@36 {
>>>>>> + compatible = "x-powers,axp805", "x-powers,axp806";
>>>>>> + reg = <0x36>;
>>>>>> + interrupt-parent = <&r_intc>;
>>>>>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>>>>>> + interrupt-controller;
>>>>>> + #interrupt-cells = <1>;
>>>>>> + x-powers,self-working-mode;
>>>>>> +
>>>>>> + regulators {
>>>>>> + reg_aldo1: aldo1 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <3300000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc-pl";
>>>>>> + };
>>>>>> +
>>>>>> + reg_aldo2: aldo2 {
>>>>>> + regulator-min-microvolt = <3300000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc-ac200";
>>>>>> + };
>>>>>> +
>>>>>> + reg_aldo3: aldo3 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <3300000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc25-dram";
>>>>>> + };
>>>>>> +
>>>>>> + reg_bldo1: bldo1 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <1800000>;
>>>>>> + regulator-max-microvolt = <1800000>;
>>>>>> + regulator-name = "vcc-bias-pll";
>>>>>> + };
>>>>>> +
>>>>>> + reg_bldo2: bldo2 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <1800000>;
>>>>>> + regulator-max-microvolt = <1800000>;
>>>>>> + regulator-name = "vcc-efuse-pcie-hdmi-io";
>>>>>> + };
>>>>>> +
>>>>>> + reg_bldo3: bldo3 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <1800000>;
>>>>>> + regulator-max-microvolt = <1800000>;
>>>>>> + regulator-name = "vcc-dcxoio";
>>>>>> + };
>>>>>> +
>>>>>> + bldo4 {
>>>>>> + /* unused */
>>>>>> + };
>>>>>> +
>>>>>> + reg_cldo1: cldo1 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <3300000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc-3v3";
>>>>>> + };
>>>>>> +
>>>>>> + reg_cldo2: cldo2 {
>>>>>> + regulator-min-microvolt = <3300000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc-wifi-1";
>>>>>> + };
>>>>>> +
>>>>>> + reg_cldo3: cldo3 {
>>>>>> + regulator-min-microvolt = <3300000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc-wifi-2";
>>>>>> + };
>>>>>> +
>>>>>> + reg_dcdca: dcdca {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <810000>;
>>>>>> + regulator-max-microvolt = <1080000>;
>>>>>> + regulator-name = "vdd-cpu";
>>>>>> + };
>>>>>> +
>>>>>> + reg_dcdcc: dcdcc {
>>>>>> + regulator-min-microvolt = <810000>;
>>>>>> + regulator-max-microvolt = <1080000>;
>>>>>> + regulator-name = "vdd-gpu";
>>>>>> + };
>>>>>> +
>>>>>> + reg_dcdcd: dcdcd {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <960000>;
>>>>>> + regulator-max-microvolt = <960000>;
>>>>>> + regulator-name = "vdd-sys";
>>>>>> + };
>>>>>> +
>>>>>> + reg_dcdce: dcdce {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <1200000>;
>>>>>> + regulator-max-microvolt = <1200000>;
>>>>>> + regulator-name = "vcc-dram";
>>>>>> + };
>>>>>> +
>>>>>> + sw {
>>>>>> + /* unused */
>>>>>> + };
>>>>>
>>>>> Can't we have a DTSI for this PMIC too?
>>>>
>>>> Back when we started adding the regulators, Mark wasn't too happy with
>>>> all the placeholders we put in the dtsi. I think we got away with it
>>>> because we had other things in there as well. That's not true for this
>>>> particular PMIC.
>>>
>>> So we need separate dtsi for this PMIC as well?
>>
>> I don't think we do. We don't gain much.
>
> Merged with Maxime's ack, and the subject prefix fixed.
> Also squashed in the Ethernet patch for this board.
H6 EMAC node changes still in ML.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [linux-sunxi] Re: [PATCH] arm64: allwinner: h6: Add OrangePi One Plus initial support
2018-09-04 14:30 ` [linux-sunxi] " Jagan Teki
@ 2018-09-04 15:10 ` Chen-Yu Tsai
0 siblings, 0 replies; 8+ messages in thread
From: Chen-Yu Tsai @ 2018-09-04 15:10 UTC (permalink / raw)
To: Jagan Teki
Cc: Jagan Teki, Maxime Ripard, Icenowy Zheng, devicetree,
linux-arm-kernel, linux-kernel, linux-sunxi
On Tue, Sep 4, 2018 at 10:31 PM Jagan Teki <jagan@openedev.com> wrote:
>
> On Monday 03 September 2018 11:05 AM, Chen-Yu Tsai wrote:
> > On Tue, Jul 31, 2018 at 9:42 PM Chen-Yu Tsai <wens@csie.org> wrote:
> >>
> >> On Tue, Jul 31, 2018 at 9:41 PM, Jagan Teki <jagan@amarulasolutions.com> wrote:
> >>> On Mon, Jul 30, 2018 at 2:47 PM, Chen-Yu Tsai <wens@csie.org> wrote:
> >>>> On Mon, Jul 30, 2018 at 5:00 PM, Maxime Ripard
> >>>> <maxime.ripard@bootlin.com> wrote:
> >>>>> Hi,
> >>>>>
> >>>>> On Sat, Jul 28, 2018 at 11:56:15PM +0530, Jagan Teki wrote:
> >>>>>> OrangePi One Plus is Allwinner H6 based open-source SBC,
> >>>>>> which support:
> >>>>>> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> >>>>>> - GPU Mali-T720
> >>>>>> - 1GB LPDDR3 RAM
> >>>>>> - AXP805 PMIC
> >>>>>> - 1Gbps GMAC via RTL8211
> >>>>>> - USB 2.0 Host, OTG
> >>>>>> - HDMI port
> >>>>>> - 5V/2A DC power supply
> >>>>>>
> >>>>>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> >>>>>> ---
> >>>>>> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> >>>>>> .../allwinner/sun50i-h6-orangepi-one-plus.dts | 150 ++++++++++++++++++
> >>>>>> 2 files changed, 151 insertions(+)
> >>>>>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
> >>>>>>
> >>>>>> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> >>>>>> index 9ffa7a038791..c38f326e7fec 100644
> >>>>>> --- a/arch/arm64/boot/dts/allwinner/Makefile
> >>>>>> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> >>>>>> @@ -15,4 +15,5 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
> >>>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
> >>>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
> >>>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
> >>>>>> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> >>>>>> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> >>>>>> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
> >>>>>> new file mode 100644
> >>>>>> index 000000000000..0612c19cd994
> >>>>>> --- /dev/null
> >>>>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts
> >>>>>> @@ -0,0 +1,150 @@
> >>>>>> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> >>>>>> +/*
> >>>>>> + * Copyright (C) 2018 Amarula Solutions
> >>>>>> + * Author: Jagan Teki <jagan@amarulasolutions.com>
> >>>>>> + */
> >>>>>> +
> >>>>>> +/dts-v1/;
> >>>>>> +
> >>>>>> +#include "sun50i-h6.dtsi"
> >>>>>> +
> >>>>>> +#include <dt-bindings/gpio/gpio.h>
> >>>>>> +
> >>>>>> +/ {
> >>>>>> + model = "OrangePi One Plus";
> >>>>>> + compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
> >>>>>> +
> >>>>>> + aliases {
> >>>>>> + serial0 = &uart0;
> >>>>>> + };
> >>>>>> +
> >>>>>> + chosen {
> >>>>>> + stdout-path = "serial0:115200n8";
> >>>>>> + };
> >>>>>> +};
> >>>>>> +
> >>>>>> +&mmc0 {
> >>>>>> + pinctrl-names = "default";
> >>>>>> + pinctrl-0 = <&mmc0_pins>;
> >>>>>> + vmmc-supply = <®_cldo1>;
> >>>>>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> >>>>>> + bus-width = <4>;
> >>>>>> + status = "okay";
> >>>>>> +};
> >>>>>> +
> >>>>>> +&r_i2c {
> >>>>>> + status = "okay";
> >>>>>> +
> >>>>>> + axp805: pmic@36 {
> >>>>>> + compatible = "x-powers,axp805", "x-powers,axp806";
> >>>>>> + reg = <0x36>;
> >>>>>> + interrupt-parent = <&r_intc>;
> >>>>>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> >>>>>> + interrupt-controller;
> >>>>>> + #interrupt-cells = <1>;
> >>>>>> + x-powers,self-working-mode;
> >>>>>> +
> >>>>>> + regulators {
> >>>>>> + reg_aldo1: aldo1 {
> >>>>>> + regulator-always-on;
> >>>>>> + regulator-min-microvolt = <3300000>;
> >>>>>> + regulator-max-microvolt = <3300000>;
> >>>>>> + regulator-name = "vcc-pl";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_aldo2: aldo2 {
> >>>>>> + regulator-min-microvolt = <3300000>;
> >>>>>> + regulator-max-microvolt = <3300000>;
> >>>>>> + regulator-name = "vcc-ac200";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_aldo3: aldo3 {
> >>>>>> + regulator-always-on;
> >>>>>> + regulator-min-microvolt = <3300000>;
> >>>>>> + regulator-max-microvolt = <3300000>;
> >>>>>> + regulator-name = "vcc25-dram";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_bldo1: bldo1 {
> >>>>>> + regulator-always-on;
> >>>>>> + regulator-min-microvolt = <1800000>;
> >>>>>> + regulator-max-microvolt = <1800000>;
> >>>>>> + regulator-name = "vcc-bias-pll";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_bldo2: bldo2 {
> >>>>>> + regulator-always-on;
> >>>>>> + regulator-min-microvolt = <1800000>;
> >>>>>> + regulator-max-microvolt = <1800000>;
> >>>>>> + regulator-name = "vcc-efuse-pcie-hdmi-io";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_bldo3: bldo3 {
> >>>>>> + regulator-always-on;
> >>>>>> + regulator-min-microvolt = <1800000>;
> >>>>>> + regulator-max-microvolt = <1800000>;
> >>>>>> + regulator-name = "vcc-dcxoio";
> >>>>>> + };
> >>>>>> +
> >>>>>> + bldo4 {
> >>>>>> + /* unused */
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_cldo1: cldo1 {
> >>>>>> + regulator-always-on;
> >>>>>> + regulator-min-microvolt = <3300000>;
> >>>>>> + regulator-max-microvolt = <3300000>;
> >>>>>> + regulator-name = "vcc-3v3";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_cldo2: cldo2 {
> >>>>>> + regulator-min-microvolt = <3300000>;
> >>>>>> + regulator-max-microvolt = <3300000>;
> >>>>>> + regulator-name = "vcc-wifi-1";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_cldo3: cldo3 {
> >>>>>> + regulator-min-microvolt = <3300000>;
> >>>>>> + regulator-max-microvolt = <3300000>;
> >>>>>> + regulator-name = "vcc-wifi-2";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_dcdca: dcdca {
> >>>>>> + regulator-always-on;
> >>>>>> + regulator-min-microvolt = <810000>;
> >>>>>> + regulator-max-microvolt = <1080000>;
> >>>>>> + regulator-name = "vdd-cpu";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_dcdcc: dcdcc {
> >>>>>> + regulator-min-microvolt = <810000>;
> >>>>>> + regulator-max-microvolt = <1080000>;
> >>>>>> + regulator-name = "vdd-gpu";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_dcdcd: dcdcd {
> >>>>>> + regulator-always-on;
> >>>>>> + regulator-min-microvolt = <960000>;
> >>>>>> + regulator-max-microvolt = <960000>;
> >>>>>> + regulator-name = "vdd-sys";
> >>>>>> + };
> >>>>>> +
> >>>>>> + reg_dcdce: dcdce {
> >>>>>> + regulator-always-on;
> >>>>>> + regulator-min-microvolt = <1200000>;
> >>>>>> + regulator-max-microvolt = <1200000>;
> >>>>>> + regulator-name = "vcc-dram";
> >>>>>> + };
> >>>>>> +
> >>>>>> + sw {
> >>>>>> + /* unused */
> >>>>>> + };
> >>>>>
> >>>>> Can't we have a DTSI for this PMIC too?
> >>>>
> >>>> Back when we started adding the regulators, Mark wasn't too happy with
> >>>> all the placeholders we put in the dtsi. I think we got away with it
> >>>> because we had other things in there as well. That's not true for this
> >>>> particular PMIC.
> >>>
> >>> So we need separate dtsi for this PMIC as well?
> >>
> >> I don't think we do. We don't gain much.
> >
> > Merged with Maxime's ack, and the subject prefix fixed.
> > Also squashed in the Ethernet patch for this board.
>
> H6 EMAC node changes still in ML.
Oops. Dropped that part. Sorry about that.
ChenYu
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2018-09-04 15:27 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-07-28 18:26 [PATCH] arm64: allwinner: h6: Add OrangePi One Plus initial support Jagan Teki
2018-07-30 9:00 ` Maxime Ripard
2018-07-30 9:17 ` Chen-Yu Tsai
2018-07-31 13:41 ` Jagan Teki
2018-07-31 13:42 ` Chen-Yu Tsai
2018-09-03 5:35 ` Chen-Yu Tsai
2018-09-04 14:30 ` [linux-sunxi] " Jagan Teki
2018-09-04 15:10 ` Chen-Yu Tsai
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).