Re: [PATCH v4 12/21] ARM: dts: imx6-apalis: Add touchscreens used on Toradex eval boards

[Oleksandr Suvorov <oleksandr.suvorov@toradex.com>]

On Mon, Aug 12, 2019 at 5:23 PM Philippe Schenker
<philippe.schenker@toradex.com> wrote:
>
> This commit adds the touchscreens from Toradex so one can enable it.
>
> Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>

Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

>
> ---
>
> Changes in v4:
> - Add Marcel Ziswiler's Ack
>
> Changes in v3:
> - Fix commit title to "...imx6-apalis:..."
>
> Changes in v2:
> - Deleted touchrevolution downstream stuff
> - Use generic node name
> - Put a better comment in there
>
>  arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts  | 31 +++++++++++++++++++
>  arch/arm/boot/dts/imx6q-apalis-eval.dts       | 13 ++++++++
>  arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts | 13 ++++++++
>  arch/arm/boot/dts/imx6q-apalis-ixora.dts      | 13 ++++++++
>  4 files changed, 70 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
> index 9a5d6c94cca4..763fb5e90bd3 100644
> --- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
> +++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
> @@ -168,6 +168,21 @@
>  &i2c3 {
>         status = "okay";
>
> +       /*
> +        * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
> +        * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
> +        */
> +       touchscreen@4a {
> +               compatible = "atmel,maxtouch";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pinctrl_pcap_1>;
> +               reg = <0x4a>;
> +               interrupt-parent = <&gpio1>;
> +               interrupts = <9 IRQ_TYPE_EDGE_FALLING>;         /* SODIMM 28 */
> +               reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;     /* SODIMM 30 */
> +               status = "disabled";
> +       };
> +
>         /* M41T0M6 real time clock on carrier board */
>         rtc_i2c: rtc@68 {
>                 compatible = "st,m41t0";
> @@ -175,6 +190,22 @@
>         };
>  };
>
> +&iomuxc {
> +       pinctrl_pcap_1: pcap-1 {
> +               fsl,pins = <
> +                       MX6QDL_PAD_GPIO_9__GPIO1_IO09   0x1b0b0 /* SODIMM 28 */
> +                       MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* SODIMM 30 */
> +               >;
> +       };
> +
> +       pinctrl_mxt_ts: mxt-ts {
> +               fsl,pins = <
> +                       MX6QDL_PAD_EIM_CS1__GPIO2_IO24  0x130b0 /* SODIMM 107 */
> +                       MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x130b0 /* SODIMM 106 */
> +               >;
> +       };
> +};
> +
>  &ipu1_di0_disp0 {
>         remote-endpoint = <&lcd_display_in>;
>  };
> diff --git a/arch/arm/boot/dts/imx6q-apalis-eval.dts b/arch/arm/boot/dts/imx6q-apalis-eval.dts
> index 0edd3043d9c1..4665e15b196d 100644
> --- a/arch/arm/boot/dts/imx6q-apalis-eval.dts
> +++ b/arch/arm/boot/dts/imx6q-apalis-eval.dts
> @@ -167,6 +167,19 @@
>  &i2c1 {
>         status = "okay";
>
> +       /*
> +        * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
> +        * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
> +        */
> +       touchscreen@4a {
> +               compatible = "atmel,maxtouch";
> +               reg = <0x4a>;
> +               interrupt-parent = <&gpio6>;
> +               interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
> +               reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
> +               status = "disabled";
> +       };
> +
>         pcie-switch@58 {
>                 compatible = "plx,pex8605";
>                 reg = <0x58>;
> diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
> index b94bb687be6b..a3fa04a97d81 100644
> --- a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
> +++ b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
> @@ -172,6 +172,19 @@
>  &i2c1 {
>         status = "okay";
>
> +       /*
> +        * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
> +        * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
> +        */
> +       touchscreen@4a {
> +               compatible = "atmel,maxtouch";
> +               reg = <0x4a>;
> +               interrupt-parent = <&gpio6>;
> +               interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
> +               reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
> +               status = "disabled";
> +       };
> +
>         /* M41T0M6 real time clock on carrier board */
>         rtc_i2c: rtc@68 {
>                 compatible = "st,m41t0";
> diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora.dts b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
> index 302fd6adc8a7..5ba49d0f4880 100644
> --- a/arch/arm/boot/dts/imx6q-apalis-ixora.dts
> +++ b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
> @@ -171,6 +171,19 @@
>  &i2c1 {
>         status = "okay";
>
> +       /*
> +        * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
> +        * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
> +        */
> +       touchscreen@4a {
> +               compatible = "atmel,maxtouch";
> +               reg = <0x4a>;
> +               interrupt-parent = <&gpio6>;
> +               interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
> +               reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
> +               status = "disabled";
> +       };
> +
>         eeprom@50 {
>                 compatible = "atmel,24c02";
>                 reg = <0x50>;
> --
> 2.22.0
>


-- 
Best regards
Oleksandr Suvorov

Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500
4800 (main line)