[PATCH] w1: omap-hdq: Simplify driver with PM runtime autosuspend

[PATCH] w1: omap-hdq: Simplify driver with PM runtime autosuspend

[Tony Lindgren]

We've had generic code handling module sysconfig and OCP reset registers
for omap variants for many years now and all the drivers really needs to
do is just call runtime PM functions.

Looks like the omap-hdq driver got only partially updated over the years
to use runtime PM, and still has lots of custom PM code left.

We can replace all the custom code for sysconfig, OCP reset, and PM with
just a few lines of runtime PM autosuspend code.

Note that the earlier driver specific usage count limit of four seems
completely artificial and should not be an issue in normal use.

Cc: Adam Ford <aford173@gmail.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---


Can you guys please review and and test on gta04 and torpedo?


 drivers/w1/masters/omap_hdq.c | 286 +++++++++++-----------------------
 1 file changed, 90 insertions(+), 196 deletions(-)

diff --git a/drivers/w1/masters/omap_hdq.c b/drivers/w1/masters/omap_hdq.c
--- a/drivers/w1/masters/omap_hdq.c
+++ b/drivers/w1/masters/omap_hdq.c
@@ -38,12 +38,6 @@
 #define OMAP_HDQ_INT_STATUS_TXCOMPLETE		BIT(2)
 #define OMAP_HDQ_INT_STATUS_RXCOMPLETE		BIT(1)
 #define OMAP_HDQ_INT_STATUS_TIMEOUT		BIT(0)
-#define OMAP_HDQ_SYSCONFIG			0x14
-#define OMAP_HDQ_SYSCONFIG_SOFTRESET		BIT(1)
-#define OMAP_HDQ_SYSCONFIG_AUTOIDLE		BIT(0)
-#define OMAP_HDQ_SYSCONFIG_NOIDLE		0x0
-#define OMAP_HDQ_SYSSTATUS			0x18
-#define OMAP_HDQ_SYSSTATUS_RESETDONE		BIT(0)
 
 #define OMAP_HDQ_FLAG_CLEAR			0
 #define OMAP_HDQ_FLAG_SET			1
@@ -62,17 +56,9 @@ struct hdq_data {
 	void __iomem		*hdq_base;
 	/* lock status update */
 	struct  mutex		hdq_mutex;
-	int			hdq_usecount;
 	u8			hdq_irqstatus;
 	/* device lock */
 	spinlock_t		hdq_spinlock;
-	/*
-	 * Used to control the call to omap_hdq_get and omap_hdq_put.
-	 * HDQ Protocol: Write the CMD|REG_address first, followed by
-	 * the data wrire or read.
-	 */
-	int			init_trans;
-	int                     rrw;
 	/* mode: 0-HDQ 1-W1 */
 	int                     mode;
 
@@ -237,41 +223,6 @@ static void omap_w1_search_bus(void *_hdq, struct w1_master *master_dev,
 	slave_found(master_dev, id);
 }
 
-static int _omap_hdq_reset(struct hdq_data *hdq_data)
-{
-	int ret;
-	u8 tmp_status;
-
-	hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
-		    OMAP_HDQ_SYSCONFIG_SOFTRESET);
-	/*
-	 * Select HDQ/1W mode & enable clocks.
-	 * It is observed that INT flags can't be cleared via a read and GO/INIT
-	 * won't return to zero if interrupt is disabled. So we always enable
-	 * interrupt.
-	 */
-	hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
-		OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
-		OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK);
-
-	/* wait for reset to complete */
-	ret = hdq_wait_for_flag(hdq_data, OMAP_HDQ_SYSSTATUS,
-		OMAP_HDQ_SYSSTATUS_RESETDONE, OMAP_HDQ_FLAG_SET, &tmp_status);
-	if (ret)
-		dev_dbg(hdq_data->dev, "timeout waiting HDQ reset, %x",
-				tmp_status);
-	else {
-		hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
-			OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
-			OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK |
-			hdq_data->mode);
-		hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
-			OMAP_HDQ_SYSCONFIG_AUTOIDLE);
-	}
-
-	return ret;
-}
-
 /* Issue break pulse to the device */
 static int omap_hdq_break(struct hdq_data *hdq_data)
 {
@@ -357,7 +308,7 @@ static int hdq_read_byte(struct hdq_data *hdq_data, u8 *val)
 		goto rtn;
 	}
 
-	if (!hdq_data->hdq_usecount) {
+	if (pm_runtime_suspended(hdq_data->dev)) {
 		ret = -EINVAL;
 		goto out;
 	}
@@ -394,80 +345,6 @@ static int hdq_read_byte(struct hdq_data *hdq_data, u8 *val)
 
 }
 
-/* Enable clocks and set the controller to HDQ/1W mode */
-static int omap_hdq_get(struct hdq_data *hdq_data)
-{
-	int ret = 0;
-
-	ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
-	if (ret < 0) {
-		ret = -EINTR;
-		goto rtn;
-	}
-
-	if (OMAP_HDQ_MAX_USER == hdq_data->hdq_usecount) {
-		dev_dbg(hdq_data->dev, "attempt to exceed the max use count");
-		ret = -EINVAL;
-		goto out;
-	} else {
-		hdq_data->hdq_usecount++;
-		try_module_get(THIS_MODULE);
-		if (1 == hdq_data->hdq_usecount) {
-
-			pm_runtime_get_sync(hdq_data->dev);
-
-			/* make sure HDQ/1W is out of reset */
-			if (!(hdq_reg_in(hdq_data, OMAP_HDQ_SYSSTATUS) &
-				OMAP_HDQ_SYSSTATUS_RESETDONE)) {
-				ret = _omap_hdq_reset(hdq_data);
-				if (ret)
-					/* back up the count */
-					hdq_data->hdq_usecount--;
-			} else {
-				/* select HDQ/1W mode & enable clocks */
-				hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
-					OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
-					OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK |
-					hdq_data->mode);
-				hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
-					OMAP_HDQ_SYSCONFIG_NOIDLE);
-				hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS);
-			}
-		}
-	}
-
-out:
-	mutex_unlock(&hdq_data->hdq_mutex);
-rtn:
-	return ret;
-}
-
-/* Disable clocks to the module */
-static int omap_hdq_put(struct hdq_data *hdq_data)
-{
-	int ret = 0;
-
-	ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
-	if (ret < 0)
-		return -EINTR;
-
-	hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
-		    OMAP_HDQ_SYSCONFIG_AUTOIDLE);
-	if (0 == hdq_data->hdq_usecount) {
-		dev_dbg(hdq_data->dev, "attempt to decrement use count"
-			" when it is zero");
-		ret = -EINVAL;
-	} else {
-		hdq_data->hdq_usecount--;
-		module_put(THIS_MODULE);
-		if (0 == hdq_data->hdq_usecount)
-			pm_runtime_put_sync(hdq_data->dev);
-	}
-	mutex_unlock(&hdq_data->hdq_mutex);
-
-	return ret;
-}
-
 /*
  * W1 triplet callback function - used for searching ROM addresses.
  * Registered only when controller is in 1-wire mode.
@@ -482,7 +359,12 @@ static u8 omap_w1_triplet(void *_hdq, u8 bdir)
 		  OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK;
 	u8 mask = ctrl | OMAP_HDQ_CTRL_STATUS_DIR;
 
-	omap_hdq_get(_hdq);
+	err = pm_runtime_get_sync(hdq_data->dev);
+	if (err < 0) {
+		pm_runtime_put_noidle(hdq_data->dev);
+
+		return err;
+	}
 
 	err = mutex_lock_interruptible(&hdq_data->hdq_mutex);
 	if (err < 0) {
@@ -549,16 +431,30 @@ static u8 omap_w1_triplet(void *_hdq, u8 bdir)
 out:
 	mutex_unlock(&hdq_data->hdq_mutex);
 rtn:
-	omap_hdq_put(_hdq);
+	pm_runtime_mark_last_busy(hdq_data->dev);
+	pm_runtime_put_autosuspend(hdq_data->dev);
+
 	return ret;
 }
 
 /* reset callback */
 static u8 omap_w1_reset_bus(void *_hdq)
 {
-	omap_hdq_get(_hdq);
-	omap_hdq_break(_hdq);
-	omap_hdq_put(_hdq);
+	struct hdq_data *hdq_data = _hdq;
+	int err;
+
+	err = pm_runtime_get_sync(hdq_data->dev);
+	if (err < 0) {
+		pm_runtime_put_noidle(hdq_data->dev);
+
+		return err;
+	}
+
+	omap_hdq_break(hdq_data);
+
+	pm_runtime_mark_last_busy(hdq_data->dev);
+	pm_runtime_put_autosuspend(hdq_data->dev);
+
 	return 0;
 }
 
@@ -569,37 +465,25 @@ static u8 omap_w1_read_byte(void *_hdq)
 	u8 val = 0;
 	int ret;
 
-	/* First write to initialize the transfer */
-	if (hdq_data->init_trans == 0)
-		omap_hdq_get(hdq_data);
+	ret = pm_runtime_get_sync(hdq_data->dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(hdq_data->dev);
+
+		return ret;
+	}
 
 	ret = hdq_read_byte(hdq_data, &val);
 	if (ret) {
-		ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
-		if (ret < 0) {
-			dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
-			return -EINTR;
-		}
-		hdq_data->init_trans = 0;
-		mutex_unlock(&hdq_data->hdq_mutex);
-		omap_hdq_put(hdq_data);
-		return -1;
+		ret = -1;
+		goto out_err;
 	}
 
 	hdq_disable_interrupt(hdq_data, OMAP_HDQ_CTRL_STATUS,
 			      ~OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK);
 
-	/* Write followed by a read, release the module */
-	if (hdq_data->init_trans) {
-		ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
-		if (ret < 0) {
-			dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
-			return -EINTR;
-		}
-		hdq_data->init_trans = 0;
-		mutex_unlock(&hdq_data->hdq_mutex);
-		omap_hdq_put(hdq_data);
-	}
+out_err:
+	pm_runtime_mark_last_busy(hdq_data->dev);
+	pm_runtime_put_autosuspend(hdq_data->dev);
 
 	return val;
 }
@@ -611,9 +495,12 @@ static void omap_w1_write_byte(void *_hdq, u8 byte)
 	int ret;
 	u8 status;
 
-	/* First write to initialize the transfer */
-	if (hdq_data->init_trans == 0)
-		omap_hdq_get(hdq_data);
+	ret = pm_runtime_get_sync(hdq_data->dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(hdq_data->dev);
+
+		return;
+	}
 
 	/*
 	 * We need to reset the slave before
@@ -623,31 +510,15 @@ static void omap_w1_write_byte(void *_hdq, u8 byte)
 	if (byte == W1_SKIP_ROM)
 		omap_hdq_break(hdq_data);
 
-	ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
-	if (ret < 0) {
-		dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
-		return;
-	}
-	hdq_data->init_trans++;
-	mutex_unlock(&hdq_data->hdq_mutex);
-
 	ret = hdq_write_byte(hdq_data, byte, &status);
 	if (ret < 0) {
 		dev_dbg(hdq_data->dev, "TX failure:Ctrl status %x\n", status);
-		return;
+		goto out_err;
 	}
 
-	/* Second write, data transferred. Release the module */
-	if (hdq_data->init_trans > 1) {
-		omap_hdq_put(hdq_data);
-		ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
-		if (ret < 0) {
-			dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
-			return;
-		}
-		hdq_data->init_trans = 0;
-		mutex_unlock(&hdq_data->hdq_mutex);
-	}
+out_err:
+	pm_runtime_mark_last_busy(hdq_data->dev);
+	pm_runtime_put_autosuspend(hdq_data->dev);
 }
 
 static struct w1_bus_master omap_w1_master = {
@@ -656,6 +527,35 @@ static struct w1_bus_master omap_w1_master = {
 	.reset_bus	= omap_w1_reset_bus,
 };
 
+static int __maybe_unused omap_hdq_runtime_suspend(struct device *dev)
+{
+	struct hdq_data *hdq_data = dev_get_drvdata(dev);
+
+	hdq_reg_out(hdq_data, 0, hdq_data->mode);
+	hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS);
+
+	return 0;
+}
+
+static int __maybe_unused omap_hdq_runtime_resume(struct device *dev)
+{
+	struct hdq_data *hdq_data = dev_get_drvdata(dev);
+
+	/* select HDQ/1W mode & enable clocks */
+	hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
+		    OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
+		    OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK |
+		    hdq_data->mode);
+	hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS);
+
+	return 0;
+}
+
+static const struct dev_pm_ops omap_hdq_pm_ops = {
+	SET_RUNTIME_PM_OPS(omap_hdq_runtime_suspend,
+			   omap_hdq_runtime_resume, NULL)
+};
+
 static int omap_hdq_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -677,23 +577,18 @@ static int omap_hdq_probe(struct platform_device *pdev)
 	if (IS_ERR(hdq_data->hdq_base))
 		return PTR_ERR(hdq_data->hdq_base);
 
-	hdq_data->hdq_usecount = 0;
-	hdq_data->rrw = 0;
 	mutex_init(&hdq_data->hdq_mutex);
 
 	pm_runtime_enable(&pdev->dev);
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev, 300);
 	ret = pm_runtime_get_sync(&pdev->dev);
 	if (ret < 0) {
+		pm_runtime_put_noidle(&pdev->dev);
 		dev_dbg(&pdev->dev, "pm_runtime_get_sync failed\n");
 		goto err_w1;
 	}
 
-	ret = _omap_hdq_reset(hdq_data);
-	if (ret) {
-		dev_dbg(&pdev->dev, "reset failed\n");
-		goto err_irq;
-	}
-
 	rev = hdq_reg_in(hdq_data, OMAP_HDQ_REVISION);
 	dev_info(&pdev->dev, "OMAP HDQ Hardware Rev %c.%c. Driver in %s mode\n",
 		(rev >> 4) + '0', (rev & 0x0f) + '0', "Interrupt");
@@ -715,7 +610,8 @@ static int omap_hdq_probe(struct platform_device *pdev)
 
 	omap_hdq_break(hdq_data);
 
-	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_mark_last_busy(&pdev->dev);
+	pm_runtime_put_autosuspend(&pdev->dev);
 
 	ret = of_property_read_string(pdev->dev.of_node, "ti,mode", &mode);
 	if (ret < 0 || !strcmp(mode, "hdq")) {
@@ -739,6 +635,7 @@ static int omap_hdq_probe(struct platform_device *pdev)
 err_irq:
 	pm_runtime_put_sync(&pdev->dev);
 err_w1:
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 
 	return ret;
@@ -746,23 +643,19 @@ static int omap_hdq_probe(struct platform_device *pdev)
 
 static int omap_hdq_remove(struct platform_device *pdev)
 {
-	struct hdq_data *hdq_data = platform_get_drvdata(pdev);
-
-	mutex_lock(&hdq_data->hdq_mutex);
+	int active;
 
-	if (hdq_data->hdq_usecount) {
-		dev_dbg(&pdev->dev, "removed when use count is not zero\n");
-		mutex_unlock(&hdq_data->hdq_mutex);
-		return -EBUSY;
-	}
+	active = pm_runtime_get_sync(&pdev->dev);
+	if (active < 0)
+		pm_runtime_put_noidle(&pdev->dev);
 
-	mutex_unlock(&hdq_data->hdq_mutex);
+	w1_remove_master_device(&omap_w1_master);
 
-	/* remove module dependency */
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
+	if (active >= 0)
+		pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 
-	w1_remove_master_device(&omap_w1_master);
-
 	return 0;
 }
 
@@ -779,6 +672,7 @@ static struct platform_driver omap_hdq_driver = {
 	.driver = {
 		.name =	"omap_hdq",
 		.of_match_table = omap_hdq_dt_ids,
+		.pm = &omap_hdq_pm_ops,
 	},
 };
 module_platform_driver(omap_hdq_driver);
-- 
2.24.1

Re: [PATCH] w1: omap-hdq: Simplify driver with PM runtime autosuspend

[Andreas Kemnade]

On Sun, 15 Dec 2019 09:38:17 -0800
Tony Lindgren <tony@atomide.com> wrote:

> We've had generic code handling module sysconfig and OCP reset registers
> for omap variants for many years now and all the drivers really needs to
> do is just call runtime PM functions.
> 
> Looks like the omap-hdq driver got only partially updated over the years
> to use runtime PM, and still has lots of custom PM code left.
> 
> We can replace all the custom code for sysconfig, OCP reset, and PM with
> just a few lines of runtime PM autosuspend code.
> 
> Note that the earlier driver specific usage count limit of four seems
> completely artificial and should not be an issue in normal use.
> 
> Cc: Adam Ford <aford173@gmail.com>
> Cc: Andrew F. Davis <afd@ti.com>
> Cc: Andreas Kemnade <andreas@kemnade.info>
> Cc: H. Nikolaus Schaller <hns@goldelico.com>
> Cc: Vignesh R <vigneshr@ti.com>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
> 
> 
> Can you guys please review and and test on gta04 and torpedo?
> 
I tried this after booting with init=/bin/bash and mounting kernel
filesystems (no off mode enabled):
root@(none):/# echo on >/sys/bus/platform/devices/480b2000.1w/power/control
root@(none):/# modprobe omap_hdq
[   49.590820] Driver for 1-wire Dallas network protocol.
[   49.598327] omap_hdq 480b2000.1w: OMAP HDQ Hardware Rev 0.5. Driver in Interrupt mode
root@(none):/# [   49.624572] w1_master_driver w1_bus_master1: Attaching one wire slave 01.000000000000 crc 3d
[   49.660980] power_supply bq27000-battery: power_supply_get_battery_info currently only supports devicetree

root@(none):/# time cat /sys/class/power_supply/bq27000-battery/voltage_now 
0

real    0m2.561s
user    0m0.008s
sys     0m0.002s
root@(none):/# time cat /sys/class/power_supply/bq27000-battery/voltage_now 
0

real    0m12.601s
user    0m0.010s
sys     0m0.002s
root@(none):/# time cat /sys/class/power_supply/bq27000-battery/voltage_now 
0

real    0m12.601s
user    0m0.010s
sys     0m0.002s
root@(none):/# 

No data could be read but some detection work seem to be done.
Of course, I also tried without that forced power on.

I hope I can find more time to analyze.
Looks like a nice cleanup but needs some work.

Regards,
Andreas

Re: [PATCH] w1: omap-hdq: Simplify driver with PM runtime autosuspend

[Andreas Kemnade]

On Sun, 15 Dec 2019 09:38:17 -0800
Tony Lindgren <tony@atomide.com> wrote:

> We've had generic code handling module sysconfig and OCP reset registers
> for omap variants for many years now and all the drivers really needs to
> do is just call runtime PM functions.
> 
> Looks like the omap-hdq driver got only partially updated over the years
> to use runtime PM, and still has lots of custom PM code left.
> 
> We can replace all the custom code for sysconfig, OCP reset, and PM with
> just a few lines of runtime PM autosuspend code.
> 
> Note that the earlier driver specific usage count limit of four seems
> completely artificial and should not be an issue in normal use.
> 
> Cc: Adam Ford <aford173@gmail.com>
> Cc: Andrew F. Davis <afd@ti.com>
> Cc: Andreas Kemnade <andreas@kemnade.info>
> Cc: H. Nikolaus Schaller <hns@goldelico.com>
> Cc: Vignesh R <vigneshr@ti.com>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
> 
> 
> Can you guys please review and and test on gta04 and torpedo?
> 
[...]
>  
> -static int _omap_hdq_reset(struct hdq_data *hdq_data)
> -{
> -	int ret;
> -	u8 tmp_status;
> -
> -	hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
> -		    OMAP_HDQ_SYSCONFIG_SOFTRESET);
> -	/*
> -	 * Select HDQ/1W mode & enable clocks.
> -	 * It is observed that INT flags can't be cleared via a read and GO/INIT
> -	 * won't return to zero if interrupt is disabled. So we always enable
> -	 * interrupt.
> -	 */

If I remember correctly this thing is critical to get the hwmod out of
reset but I need to examine that again:

> -	hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
> -		OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
> -		OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK);
> -
> -	/* wait for reset to complete */
> -	ret = hdq_wait_for_flag(hdq_data, OMAP_HDQ_SYSSTATUS,
> -		OMAP_HDQ_SYSSTATUS_RESETDONE, OMAP_HDQ_FLAG_SET, &tmp_status);
> -	if (ret)
> -		dev_dbg(hdq_data->dev, "timeout waiting HDQ reset, %x",
> -				tmp_status);
> -	else {
> -		hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
> -			OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
> -			OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK |
> -			hdq_data->mode);
> -		hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
> -			OMAP_HDQ_SYSCONFIG_AUTOIDLE);
> -	}
> -
> -	return ret;
> -}

I will probably do more testing the next days.

Regards,
Andreas

Re: [PATCH] w1: omap-hdq: Simplify driver with PM runtime autosuspend

[Tony Lindgren]

Hi,

* Andreas Kemnade <andreas@kemnade.info> [191215 22:04]:
> On Sun, 15 Dec 2019 09:38:17 -0800
> If I remember correctly this thing is critical to get the hwmod out of
> reset but I need to examine that again:

Thanks for testing, yes that's what I thought might cause it
too, but nope :)

We currently disable interrupts for some reason after
the first read. That won't play with runtime PM autosuspend
at all as we never enable them again until the device has
idled. Can you try the following additional patch on top?

Regards,

Tony

8< -----------------
diff --git a/drivers/w1/masters/omap_hdq.c b/drivers/w1/masters/omap_hdq.c
--- a/drivers/w1/masters/omap_hdq.c
+++ b/drivers/w1/masters/omap_hdq.c
@@ -86,15 +86,6 @@ static inline u8 hdq_reg_merge(struct hdq_data *hdq_data, u32 offset,
 	return new_val;
 }
 
-static void hdq_disable_interrupt(struct hdq_data *hdq_data, u32 offset,
-				  u32 mask)
-{
-	u32 ie;
-
-	ie = readl(hdq_data->hdq_base + offset);
-	writel(ie & mask, hdq_data->hdq_base + offset);
-}
-
 /*
  * Wait for one or more bits in flag change.
  * HDQ_FLAG_SET: wait until any bit in the flag is set.
@@ -474,15 +465,9 @@ static u8 omap_w1_read_byte(void *_hdq)
 	}
 
 	ret = hdq_read_byte(hdq_data, &val);
-	if (ret) {
+	if (ret)
 		ret = -1;
-		goto out_err;
-	}
 
-	hdq_disable_interrupt(hdq_data, OMAP_HDQ_CTRL_STATUS,
-			      ~OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK);
-
-out_err:
 	pm_runtime_mark_last_busy(hdq_data->dev);
 	pm_runtime_put_autosuspend(hdq_data->dev);
 

Re: [PATCH] w1: omap-hdq: Simplify driver with PM runtime autosuspend

[Tony Lindgren]

* Tony Lindgren <tony@atomide.com> [191216 03:10]:
> Hi,
> 
> * Andreas Kemnade <andreas@kemnade.info> [191215 22:04]:
> > On Sun, 15 Dec 2019 09:38:17 -0800
> > If I remember correctly this thing is critical to get the hwmod out of
> > reset but I need to examine that again:
> 
> Thanks for testing, yes that's what I thought might cause it
> too, but nope :)
> 
> We currently disable interrupts for some reason after
> the first read. That won't play with runtime PM autosuspend
> at all as we never enable them again until the device has
> idled. Can you try the following additional patch on top?

And we should probably do the following too to make sure
the mode is initialized before we call runtime PM.

Regards,

Tony

8< -------------------
diff --git a/drivers/w1/masters/omap_hdq.c b/drivers/w1/masters/omap_hdq.c
--- a/drivers/w1/masters/omap_hdq.c
+++ b/drivers/w1/masters/omap_hdq.c
@@ -565,6 +565,15 @@ static int omap_hdq_probe(struct platform_device *pdev)
 
 	mutex_init(&hdq_data->hdq_mutex);
 
+	ret = of_property_read_string(pdev->dev.of_node, "ti,mode", &mode);
+	if (ret < 0 || !strcmp(mode, "hdq")) {
+		hdq_data->mode = 0;
+		omap_w1_master.search = omap_w1_search_bus;
+	} else {
+		hdq_data->mode = 1;
+		omap_w1_master.triplet = omap_w1_triplet;
+	}
+
 	pm_runtime_enable(&pdev->dev);
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_set_autosuspend_delay(&pdev->dev, 300);
@@ -599,15 +608,6 @@ static int omap_hdq_probe(struct platform_device *pdev)
 	pm_runtime_mark_last_busy(&pdev->dev);
 	pm_runtime_put_autosuspend(&pdev->dev);
 
-	ret = of_property_read_string(pdev->dev.of_node, "ti,mode", &mode);
-	if (ret < 0 || !strcmp(mode, "hdq")) {
-		hdq_data->mode = 0;
-		omap_w1_master.search = omap_w1_search_bus;
-	} else {
-		hdq_data->mode = 1;
-		omap_w1_master.triplet = omap_w1_triplet;
-	}
-
 	omap_w1_master.data = hdq_data;
 
 	ret = w1_add_master_device(&omap_w1_master);

Re: [PATCH] w1: omap-hdq: Simplify driver with PM runtime autosuspend

[Andreas Kemnade]

[-- Attachment #1: Type: text/plain, Size: 1049 bytes --]

On Sun, 15 Dec 2019 19:16:37 -0800
Tony Lindgren <tony@atomide.com> wrote:

> * Tony Lindgren <tony@atomide.com> [191216 03:10]:
> > Hi,
> > 
> > * Andreas Kemnade <andreas@kemnade.info> [191215 22:04]:  
> > > On Sun, 15 Dec 2019 09:38:17 -0800
> > > If I remember correctly this thing is critical to get the hwmod out of
> > > reset but I need to examine that again:  
> > 
> > Thanks for testing, yes that's what I thought might cause it
> > too, but nope :)
> > 
> > We currently disable interrupts for some reason after
> > the first read. That won't play with runtime PM autosuspend
> > at all as we never enable them again until the device has
> > idled. Can you try the following additional patch on top?  
> 
> And we should probably do the following too to make sure
> the mode is initialized before we call runtime PM.
> 
CM_FCLKEN1/IDLEST1_CORE seem to behave, reading also works 

With these two additional patches this deserves a
Tested-By: Andreas Kemnade <andreas@kemnade.info> # gta04

Regards,
Andreas

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH] w1: omap-hdq: Simplify driver with PM runtime autosuspend

[Adam Ford]

On Mon, Dec 16, 2019 at 7:48 AM Andreas Kemnade <andreas@kemnade.info> wrote:
>
> On Sun, 15 Dec 2019 19:16:37 -0800
> Tony Lindgren <tony@atomide.com> wrote:
>
> > * Tony Lindgren <tony@atomide.com> [191216 03:10]:
> > > Hi,
> > >
> > > * Andreas Kemnade <andreas@kemnade.info> [191215 22:04]:
> > > > On Sun, 15 Dec 2019 09:38:17 -0800
> > > > If I remember correctly this thing is critical to get the hwmod out of
> > > > reset but I need to examine that again:
> > >
> > > Thanks for testing, yes that's what I thought might cause it
> > > too, but nope :)
> > >
> > > We currently disable interrupts for some reason after
> > > the first read. That won't play with runtime PM autosuspend
> > > at all as we never enable them again until the device has
> > > idled. Can you try the following additional patch on top?
> >
> > And we should probably do the following too to make sure
> > the mode is initialized before we call runtime PM.
> >
> CM_FCLKEN1/IDLEST1_CORE seem to behave, reading also works
>
> With these two additional patches this deserves a
> Tested-By: Andreas Kemnade <andreas@kemnade.info> # gta04

Tony,

Any way you can do a V2 patch with the other stuff added?  Pulling the
patches from gmail doesn't work.  I think G-mail does something weird
because they don't apply cleanly, so I have to download the patches
from patchwork.  I should be able to test it today.

thanks

adam
>
> Regards,
> Andreas

Re: [PATCH] w1: omap-hdq: Simplify driver with PM runtime autosuspend

[Tony Lindgren]

* Adam Ford <aford173@gmail.com> [191216 13:58]:
> On Mon, Dec 16, 2019 at 7:48 AM Andreas Kemnade <andreas@kemnade.info> wrote:
> >
> > On Sun, 15 Dec 2019 19:16:37 -0800
> > Tony Lindgren <tony@atomide.com> wrote:
> >
> > > * Tony Lindgren <tony@atomide.com> [191216 03:10]:
> > > > Hi,
> > > >
> > > > * Andreas Kemnade <andreas@kemnade.info> [191215 22:04]:
> > > > > On Sun, 15 Dec 2019 09:38:17 -0800
> > > > > If I remember correctly this thing is critical to get the hwmod out of
> > > > > reset but I need to examine that again:
> > > >
> > > > Thanks for testing, yes that's what I thought might cause it
> > > > too, but nope :)
> > > >
> > > > We currently disable interrupts for some reason after
> > > > the first read. That won't play with runtime PM autosuspend
> > > > at all as we never enable them again until the device has
> > > > idled. Can you try the following additional patch on top?
> > >
> > > And we should probably do the following too to make sure
> > > the mode is initialized before we call runtime PM.
> > >
> > CM_FCLKEN1/IDLEST1_CORE seem to behave, reading also works
> >
> > With these two additional patches this deserves a
> > Tested-By: Andreas Kemnade <andreas@kemnade.info> # gta04
> 
> Tony,
> 
> Any way you can do a V2 patch with the other stuff added?  Pulling the
> patches from gmail doesn't work.  I think G-mail does something weird
> because they don't apply cleanly, so I have to download the patches
> from patchwork.  I should be able to test it today.

OK sent out v2 with the two change folded in. The ti,mode = "1w"
still needs to be tested if anybody has a sensor to test with.
I verified the battery ds2502 gets properly detected on droid4 battery,
in "1w" mode, but so far no luck actually reading the nvmem with the
newish w1_ds250x driver.

Regards,

Tony

Re: [PATCH] w1: omap-hdq: Simplify driver with PM runtime autosuspend

[Adam Ford]

On Sun, Dec 15, 2019 at 11:38 AM Tony Lindgren <tony@atomide.com> wrote:
>
> We've had generic code handling module sysconfig and OCP reset registers
> for omap variants for many years now and all the drivers really needs to
> do is just call runtime PM functions.
>
> Looks like the omap-hdq driver got only partially updated over the years
> to use runtime PM, and still has lots of custom PM code left.
>
> We can replace all the custom code for sysconfig, OCP reset, and PM with
> just a few lines of runtime PM autosuspend code.
>
> Note that the earlier driver specific usage count limit of four seems
> completely artificial and should not be an issue in normal use.
>
> Cc: Adam Ford <aford173@gmail.com>
> Cc: Andrew F. Davis <afd@ti.com>
> Cc: Andreas Kemnade <andreas@kemnade.info>
> Cc: H. Nikolaus Schaller <hns@goldelico.com>
> Cc: Vignesh R <vigneshr@ti.com>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
>
>
> Can you guys please review and and test on gta04 and torpedo?

I will try to test this series early this week.

adam
>
>
>  drivers/w1/masters/omap_hdq.c | 286 +++++++++++-----------------------
>  1 file changed, 90 insertions(+), 196 deletions(-)
>
> diff --git a/drivers/w1/masters/omap_hdq.c b/drivers/w1/masters/omap_hdq.c
> --- a/drivers/w1/masters/omap_hdq.c
> +++ b/drivers/w1/masters/omap_hdq.c
> @@ -38,12 +38,6 @@
>  #define OMAP_HDQ_INT_STATUS_TXCOMPLETE         BIT(2)
>  #define OMAP_HDQ_INT_STATUS_RXCOMPLETE         BIT(1)
>  #define OMAP_HDQ_INT_STATUS_TIMEOUT            BIT(0)
> -#define OMAP_HDQ_SYSCONFIG                     0x14
> -#define OMAP_HDQ_SYSCONFIG_SOFTRESET           BIT(1)
> -#define OMAP_HDQ_SYSCONFIG_AUTOIDLE            BIT(0)
> -#define OMAP_HDQ_SYSCONFIG_NOIDLE              0x0
> -#define OMAP_HDQ_SYSSTATUS                     0x18
> -#define OMAP_HDQ_SYSSTATUS_RESETDONE           BIT(0)
>
>  #define OMAP_HDQ_FLAG_CLEAR                    0
>  #define OMAP_HDQ_FLAG_SET                      1
> @@ -62,17 +56,9 @@ struct hdq_data {
>         void __iomem            *hdq_base;
>         /* lock status update */
>         struct  mutex           hdq_mutex;
> -       int                     hdq_usecount;
>         u8                      hdq_irqstatus;
>         /* device lock */
>         spinlock_t              hdq_spinlock;
> -       /*
> -        * Used to control the call to omap_hdq_get and omap_hdq_put.
> -        * HDQ Protocol: Write the CMD|REG_address first, followed by
> -        * the data wrire or read.
> -        */
> -       int                     init_trans;
> -       int                     rrw;
>         /* mode: 0-HDQ 1-W1 */
>         int                     mode;
>
> @@ -237,41 +223,6 @@ static void omap_w1_search_bus(void *_hdq, struct w1_master *master_dev,
>         slave_found(master_dev, id);
>  }
>
> -static int _omap_hdq_reset(struct hdq_data *hdq_data)
> -{
> -       int ret;
> -       u8 tmp_status;
> -
> -       hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
> -                   OMAP_HDQ_SYSCONFIG_SOFTRESET);
> -       /*
> -        * Select HDQ/1W mode & enable clocks.
> -        * It is observed that INT flags can't be cleared via a read and GO/INIT
> -        * won't return to zero if interrupt is disabled. So we always enable
> -        * interrupt.
> -        */
> -       hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
> -               OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
> -               OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK);
> -
> -       /* wait for reset to complete */
> -       ret = hdq_wait_for_flag(hdq_data, OMAP_HDQ_SYSSTATUS,
> -               OMAP_HDQ_SYSSTATUS_RESETDONE, OMAP_HDQ_FLAG_SET, &tmp_status);
> -       if (ret)
> -               dev_dbg(hdq_data->dev, "timeout waiting HDQ reset, %x",
> -                               tmp_status);
> -       else {
> -               hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
> -                       OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
> -                       OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK |
> -                       hdq_data->mode);
> -               hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
> -                       OMAP_HDQ_SYSCONFIG_AUTOIDLE);
> -       }
> -
> -       return ret;
> -}
> -
>  /* Issue break pulse to the device */
>  static int omap_hdq_break(struct hdq_data *hdq_data)
>  {
> @@ -357,7 +308,7 @@ static int hdq_read_byte(struct hdq_data *hdq_data, u8 *val)
>                 goto rtn;
>         }
>
> -       if (!hdq_data->hdq_usecount) {
> +       if (pm_runtime_suspended(hdq_data->dev)) {
>                 ret = -EINVAL;
>                 goto out;
>         }
> @@ -394,80 +345,6 @@ static int hdq_read_byte(struct hdq_data *hdq_data, u8 *val)
>
>  }
>
> -/* Enable clocks and set the controller to HDQ/1W mode */
> -static int omap_hdq_get(struct hdq_data *hdq_data)
> -{
> -       int ret = 0;
> -
> -       ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
> -       if (ret < 0) {
> -               ret = -EINTR;
> -               goto rtn;
> -       }
> -
> -       if (OMAP_HDQ_MAX_USER == hdq_data->hdq_usecount) {
> -               dev_dbg(hdq_data->dev, "attempt to exceed the max use count");
> -               ret = -EINVAL;
> -               goto out;
> -       } else {
> -               hdq_data->hdq_usecount++;
> -               try_module_get(THIS_MODULE);
> -               if (1 == hdq_data->hdq_usecount) {
> -
> -                       pm_runtime_get_sync(hdq_data->dev);
> -
> -                       /* make sure HDQ/1W is out of reset */
> -                       if (!(hdq_reg_in(hdq_data, OMAP_HDQ_SYSSTATUS) &
> -                               OMAP_HDQ_SYSSTATUS_RESETDONE)) {
> -                               ret = _omap_hdq_reset(hdq_data);
> -                               if (ret)
> -                                       /* back up the count */
> -                                       hdq_data->hdq_usecount--;
> -                       } else {
> -                               /* select HDQ/1W mode & enable clocks */
> -                               hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
> -                                       OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
> -                                       OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK |
> -                                       hdq_data->mode);
> -                               hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
> -                                       OMAP_HDQ_SYSCONFIG_NOIDLE);
> -                               hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS);
> -                       }
> -               }
> -       }
> -
> -out:
> -       mutex_unlock(&hdq_data->hdq_mutex);
> -rtn:
> -       return ret;
> -}
> -
> -/* Disable clocks to the module */
> -static int omap_hdq_put(struct hdq_data *hdq_data)
> -{
> -       int ret = 0;
> -
> -       ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
> -       if (ret < 0)
> -               return -EINTR;
> -
> -       hdq_reg_out(hdq_data, OMAP_HDQ_SYSCONFIG,
> -                   OMAP_HDQ_SYSCONFIG_AUTOIDLE);
> -       if (0 == hdq_data->hdq_usecount) {
> -               dev_dbg(hdq_data->dev, "attempt to decrement use count"
> -                       " when it is zero");
> -               ret = -EINVAL;
> -       } else {
> -               hdq_data->hdq_usecount--;
> -               module_put(THIS_MODULE);
> -               if (0 == hdq_data->hdq_usecount)
> -                       pm_runtime_put_sync(hdq_data->dev);
> -       }
> -       mutex_unlock(&hdq_data->hdq_mutex);
> -
> -       return ret;
> -}
> -
>  /*
>   * W1 triplet callback function - used for searching ROM addresses.
>   * Registered only when controller is in 1-wire mode.
> @@ -482,7 +359,12 @@ static u8 omap_w1_triplet(void *_hdq, u8 bdir)
>                   OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK;
>         u8 mask = ctrl | OMAP_HDQ_CTRL_STATUS_DIR;
>
> -       omap_hdq_get(_hdq);
> +       err = pm_runtime_get_sync(hdq_data->dev);
> +       if (err < 0) {
> +               pm_runtime_put_noidle(hdq_data->dev);
> +
> +               return err;
> +       }
>
>         err = mutex_lock_interruptible(&hdq_data->hdq_mutex);
>         if (err < 0) {
> @@ -549,16 +431,30 @@ static u8 omap_w1_triplet(void *_hdq, u8 bdir)
>  out:
>         mutex_unlock(&hdq_data->hdq_mutex);
>  rtn:
> -       omap_hdq_put(_hdq);
> +       pm_runtime_mark_last_busy(hdq_data->dev);
> +       pm_runtime_put_autosuspend(hdq_data->dev);
> +
>         return ret;
>  }
>
>  /* reset callback */
>  static u8 omap_w1_reset_bus(void *_hdq)
>  {
> -       omap_hdq_get(_hdq);
> -       omap_hdq_break(_hdq);
> -       omap_hdq_put(_hdq);
> +       struct hdq_data *hdq_data = _hdq;
> +       int err;
> +
> +       err = pm_runtime_get_sync(hdq_data->dev);
> +       if (err < 0) {
> +               pm_runtime_put_noidle(hdq_data->dev);
> +
> +               return err;
> +       }
> +
> +       omap_hdq_break(hdq_data);
> +
> +       pm_runtime_mark_last_busy(hdq_data->dev);
> +       pm_runtime_put_autosuspend(hdq_data->dev);
> +
>         return 0;
>  }
>
> @@ -569,37 +465,25 @@ static u8 omap_w1_read_byte(void *_hdq)
>         u8 val = 0;
>         int ret;
>
> -       /* First write to initialize the transfer */
> -       if (hdq_data->init_trans == 0)
> -               omap_hdq_get(hdq_data);
> +       ret = pm_runtime_get_sync(hdq_data->dev);
> +       if (ret < 0) {
> +               pm_runtime_put_noidle(hdq_data->dev);
> +
> +               return ret;
> +       }
>
>         ret = hdq_read_byte(hdq_data, &val);
>         if (ret) {
> -               ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
> -               if (ret < 0) {
> -                       dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
> -                       return -EINTR;
> -               }
> -               hdq_data->init_trans = 0;
> -               mutex_unlock(&hdq_data->hdq_mutex);
> -               omap_hdq_put(hdq_data);
> -               return -1;
> +               ret = -1;
> +               goto out_err;
>         }
>
>         hdq_disable_interrupt(hdq_data, OMAP_HDQ_CTRL_STATUS,
>                               ~OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK);
>
> -       /* Write followed by a read, release the module */
> -       if (hdq_data->init_trans) {
> -               ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
> -               if (ret < 0) {
> -                       dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
> -                       return -EINTR;
> -               }
> -               hdq_data->init_trans = 0;
> -               mutex_unlock(&hdq_data->hdq_mutex);
> -               omap_hdq_put(hdq_data);
> -       }
> +out_err:
> +       pm_runtime_mark_last_busy(hdq_data->dev);
> +       pm_runtime_put_autosuspend(hdq_data->dev);
>
>         return val;
>  }
> @@ -611,9 +495,12 @@ static void omap_w1_write_byte(void *_hdq, u8 byte)
>         int ret;
>         u8 status;
>
> -       /* First write to initialize the transfer */
> -       if (hdq_data->init_trans == 0)
> -               omap_hdq_get(hdq_data);
> +       ret = pm_runtime_get_sync(hdq_data->dev);
> +       if (ret < 0) {
> +               pm_runtime_put_noidle(hdq_data->dev);
> +
> +               return;
> +       }
>
>         /*
>          * We need to reset the slave before
> @@ -623,31 +510,15 @@ static void omap_w1_write_byte(void *_hdq, u8 byte)
>         if (byte == W1_SKIP_ROM)
>                 omap_hdq_break(hdq_data);
>
> -       ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
> -       if (ret < 0) {
> -               dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
> -               return;
> -       }
> -       hdq_data->init_trans++;
> -       mutex_unlock(&hdq_data->hdq_mutex);
> -
>         ret = hdq_write_byte(hdq_data, byte, &status);
>         if (ret < 0) {
>                 dev_dbg(hdq_data->dev, "TX failure:Ctrl status %x\n", status);
> -               return;
> +               goto out_err;
>         }
>
> -       /* Second write, data transferred. Release the module */
> -       if (hdq_data->init_trans > 1) {
> -               omap_hdq_put(hdq_data);
> -               ret = mutex_lock_interruptible(&hdq_data->hdq_mutex);
> -               if (ret < 0) {
> -                       dev_dbg(hdq_data->dev, "Could not acquire mutex\n");
> -                       return;
> -               }
> -               hdq_data->init_trans = 0;
> -               mutex_unlock(&hdq_data->hdq_mutex);
> -       }
> +out_err:
> +       pm_runtime_mark_last_busy(hdq_data->dev);
> +       pm_runtime_put_autosuspend(hdq_data->dev);
>  }
>
>  static struct w1_bus_master omap_w1_master = {
> @@ -656,6 +527,35 @@ static struct w1_bus_master omap_w1_master = {
>         .reset_bus      = omap_w1_reset_bus,
>  };
>
> +static int __maybe_unused omap_hdq_runtime_suspend(struct device *dev)
> +{
> +       struct hdq_data *hdq_data = dev_get_drvdata(dev);
> +
> +       hdq_reg_out(hdq_data, 0, hdq_data->mode);
> +       hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS);
> +
> +       return 0;
> +}
> +
> +static int __maybe_unused omap_hdq_runtime_resume(struct device *dev)
> +{
> +       struct hdq_data *hdq_data = dev_get_drvdata(dev);
> +
> +       /* select HDQ/1W mode & enable clocks */
> +       hdq_reg_out(hdq_data, OMAP_HDQ_CTRL_STATUS,
> +                   OMAP_HDQ_CTRL_STATUS_CLOCKENABLE |
> +                   OMAP_HDQ_CTRL_STATUS_INTERRUPTMASK |
> +                   hdq_data->mode);
> +       hdq_reg_in(hdq_data, OMAP_HDQ_INT_STATUS);
> +
> +       return 0;
> +}
> +
> +static const struct dev_pm_ops omap_hdq_pm_ops = {
> +       SET_RUNTIME_PM_OPS(omap_hdq_runtime_suspend,
> +                          omap_hdq_runtime_resume, NULL)
> +};
> +
>  static int omap_hdq_probe(struct platform_device *pdev)
>  {
>         struct device *dev = &pdev->dev;
> @@ -677,23 +577,18 @@ static int omap_hdq_probe(struct platform_device *pdev)
>         if (IS_ERR(hdq_data->hdq_base))
>                 return PTR_ERR(hdq_data->hdq_base);
>
> -       hdq_data->hdq_usecount = 0;
> -       hdq_data->rrw = 0;
>         mutex_init(&hdq_data->hdq_mutex);
>
>         pm_runtime_enable(&pdev->dev);
> +       pm_runtime_use_autosuspend(&pdev->dev);
> +       pm_runtime_set_autosuspend_delay(&pdev->dev, 300);
>         ret = pm_runtime_get_sync(&pdev->dev);
>         if (ret < 0) {
> +               pm_runtime_put_noidle(&pdev->dev);
>                 dev_dbg(&pdev->dev, "pm_runtime_get_sync failed\n");
>                 goto err_w1;
>         }
>
> -       ret = _omap_hdq_reset(hdq_data);
> -       if (ret) {
> -               dev_dbg(&pdev->dev, "reset failed\n");
> -               goto err_irq;
> -       }
> -
>         rev = hdq_reg_in(hdq_data, OMAP_HDQ_REVISION);
>         dev_info(&pdev->dev, "OMAP HDQ Hardware Rev %c.%c. Driver in %s mode\n",
>                 (rev >> 4) + '0', (rev & 0x0f) + '0', "Interrupt");
> @@ -715,7 +610,8 @@ static int omap_hdq_probe(struct platform_device *pdev)
>
>         omap_hdq_break(hdq_data);
>
> -       pm_runtime_put_sync(&pdev->dev);
> +       pm_runtime_mark_last_busy(&pdev->dev);
> +       pm_runtime_put_autosuspend(&pdev->dev);
>
>         ret = of_property_read_string(pdev->dev.of_node, "ti,mode", &mode);
>         if (ret < 0 || !strcmp(mode, "hdq")) {
> @@ -739,6 +635,7 @@ static int omap_hdq_probe(struct platform_device *pdev)
>  err_irq:
>         pm_runtime_put_sync(&pdev->dev);
>  err_w1:
> +       pm_runtime_dont_use_autosuspend(&pdev->dev);
>         pm_runtime_disable(&pdev->dev);
>
>         return ret;
> @@ -746,23 +643,19 @@ static int omap_hdq_probe(struct platform_device *pdev)
>
>  static int omap_hdq_remove(struct platform_device *pdev)
>  {
> -       struct hdq_data *hdq_data = platform_get_drvdata(pdev);
> -
> -       mutex_lock(&hdq_data->hdq_mutex);
> +       int active;
>
> -       if (hdq_data->hdq_usecount) {
> -               dev_dbg(&pdev->dev, "removed when use count is not zero\n");
> -               mutex_unlock(&hdq_data->hdq_mutex);
> -               return -EBUSY;
> -       }
> +       active = pm_runtime_get_sync(&pdev->dev);
> +       if (active < 0)
> +               pm_runtime_put_noidle(&pdev->dev);
>
> -       mutex_unlock(&hdq_data->hdq_mutex);
> +       w1_remove_master_device(&omap_w1_master);
>
> -       /* remove module dependency */
> +       pm_runtime_dont_use_autosuspend(&pdev->dev);
> +       if (active >= 0)
> +               pm_runtime_put_sync(&pdev->dev);
>         pm_runtime_disable(&pdev->dev);
>
> -       w1_remove_master_device(&omap_w1_master);
> -
>         return 0;
>  }
>
> @@ -779,6 +672,7 @@ static struct platform_driver omap_hdq_driver = {
>         .driver = {
>                 .name = "omap_hdq",
>                 .of_match_table = omap_hdq_dt_ids,
> +               .pm = &omap_hdq_pm_ops,
>         },
>  };
>  module_platform_driver(omap_hdq_driver);
> --
> 2.24.1