* [PATCH v2 2/3] power: supply: Add driver for Microchip UCS1002
2019-04-29 5:47 [PATCH v2 0/3] Driver for UCS1002 Andrey Smirnov
2019-04-29 5:47 ` [PATCH v2 1/3] power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant Andrey Smirnov
@ 2019-04-29 5:47 ` Andrey Smirnov
2019-04-29 10:27 ` Lucas Stach
2019-04-29 5:47 ` [PATCH v2 3/3] dt-bindings: power: supply: Add bindings " Andrey Smirnov
2 siblings, 1 reply; 6+ messages in thread
From: Andrey Smirnov @ 2019-04-29 5:47 UTC (permalink / raw)
To: linux-pm
Cc: Andrey Smirnov, Enric Balletbo Serra, Chris Healy, Lucas Stach,
Fabio Estevam, Guenter Roeck, Sebastian Reichel, linux-kernel
Add driver for Microchip UCS1002 Programmable USB Port Power
Controller with Charger Emulation. The driver exposed a power supply
device to control/monitor various parameter of the device as well as a
regulator to allow controlling VBUS line.
Signed-off-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
---
drivers/power/supply/Kconfig | 9 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/ucs1002_power.c | 646 +++++++++++++++++++++++++++
3 files changed, 656 insertions(+)
create mode 100644 drivers/power/supply/ucs1002_power.c
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index e901b9879e7e..c614c8a196f3 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -660,4 +660,13 @@ config FUEL_GAUGE_SC27XX
Say Y here to enable support for fuel gauge with SC27XX
PMIC chips.
+config CHARGER_UCS1002
+ tristate "Microchip UCS1002 USB Port Power Controller"
+ depends on I2C
+ depends on OF
+ select REGMAP_I2C
+ help
+ Say Y to enable support for Microchip UCS1002 Programmable
+ USB Port Power Controller with Charger Emulation.
+
endif # POWER_SUPPLY
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index b731c2a9b695..c56803a9e4fe 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -87,3 +87,4 @@ obj-$(CONFIG_AXP288_CHARGER) += axp288_charger.o
obj-$(CONFIG_CHARGER_CROS_USBPD) += cros_usbpd-charger.o
obj-$(CONFIG_CHARGER_SC2731) += sc2731_charger.o
obj-$(CONFIG_FUEL_GAUGE_SC27XX) += sc27xx_fuel_gauge.o
+obj-$(CONFIG_CHARGER_UCS1002) += ucs1002_power.o
diff --git a/drivers/power/supply/ucs1002_power.c b/drivers/power/supply/ucs1002_power.c
new file mode 100644
index 000000000000..a1f9d1ea750a
--- /dev/null
+++ b/drivers/power/supply/ucs1002_power.c
@@ -0,0 +1,646 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Driver for UCS1002 Programmable USB Port Power Controller
+ *
+ * Copyright (C) 2019 Zodiac Inflight Innovations
+ */
+#include <linux/bits.h>
+#include <linux/freezer.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/kthread.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+/* UCS1002 Registers */
+#define UCS1002_REG_CURRENT_MEASUREMENT 0x00
+
+/*
+ * The Total Accumulated Charge registers store the total accumulated
+ * charge delivered from the VS source to a portable device. The total
+ * value is calculated using four registers, from 01h to 04h. The bit
+ * weighting of the registers is given in mA/hrs.
+ */
+#define UCS1002_REG_TOTAL_ACC_CHARGE 0x01
+
+/* Other Status Register */
+#define UCS1002_REG_OTHER_STATUS 0x0f
+# define F_ADET_PIN BIT(4)
+# define F_CHG_ACT BIT(3)
+
+/* Interrupt Status */
+#define UCS1002_REG_INTERRUPT_STATUS 0x10
+# define F_DISCHARGE_ERR BIT(6)
+# define F_RESET BIT(5)
+# define F_MIN_KEEP_OUT BIT(4)
+# define F_TSD BIT(3)
+# define F_OVER_VOLT BIT(2)
+# define F_BACK_VOLT BIT(1)
+# define F_OVER_ILIM BIT(0)
+
+/* Pin Status Register */
+#define UCS1002_REG_PIN_STATUS 0x14
+# define UCS1002_PWR_STATE_MASK 0x03
+# define F_PWR_EN_PIN BIT(6)
+# define F_M2_PIN BIT(5)
+# define F_M1_PIN BIT(4)
+# define F_EM_EN_PIN BIT(3)
+# define F_SEL_PIN BIT(2)
+# define F_ACTIVE_MODE_MASK GENMASK(5, 3)
+# define F_ACTIVE_MODE_PASSTHROUGH F_M2_PIN
+# define F_ACTIVE_MODE_DEDICATED F_EM_EN_PIN
+# define F_ACTIVE_MODE_BC12_DCP (F_M2_PIN | F_EM_EN_PIN)
+# define F_ACTIVE_MODE_BC12_SDP F_M1_PIN
+# define F_ACTIVE_MODE_BC12_CDP (F_M1_PIN | F_M2_PIN | F_EM_EN_PIN)
+
+/* General Configuration Register */
+#define UCS1002_REG_GENERAL_CFG 0x15
+# define F_RATION_EN BIT(3)
+
+/* Emulation Configuration Register */
+#define UCS1002_REG_EMU_CFG 0x16
+
+/* Switch Configuration Register */
+#define UCS1002_REG_SWITCH_CFG 0x17
+# define F_PIN_IGNORE BIT(7)
+# define F_EM_EN_SET BIT(5)
+# define F_M2_SET BIT(4)
+# define F_M1_SET BIT(3)
+# define F_S0_SET BIT(2)
+# define F_PWR_EN_SET BIT(1)
+# define F_LATCH_SET BIT(0)
+# define V_SET_ACTIVE_MODE_MASK GENMASK(5, 3)
+# define V_SET_ACTIVE_MODE_PASSTHROUGH F_M2_SET
+# define V_SET_ACTIVE_MODE_DEDICATED F_EM_EN_SET
+# define V_SET_ACTIVE_MODE_BC12_DCP (F_M2_SET | F_EM_EN_SET)
+# define V_SET_ACTIVE_MODE_BC12_SDP F_M1_SET
+# define V_SET_ACTIVE_MODE_BC12_CDP (F_M1_SET | F_M2_SET | F_EM_EN_SET)
+
+/* Current Limit Register */
+#define UCS1002_REG_ILIMIT 0x19
+# define UCS1002_ILIM_SW_MASK GENMASK(3, 0)
+
+/* Product ID */
+#define UCS1002_REG_PRODUCT_ID 0xfd
+# define UCS1002_PRODUCT_ID 0x4e
+
+/* Manufacture name */
+#define UCS1002_MANUFACTURER "SMSC"
+
+struct ucs1002_info {
+ struct power_supply *charger;
+ struct i2c_client *client;
+ struct regmap *regmap;
+ struct regulator_desc *regulator_descriptor;
+ bool present;
+};
+
+static enum power_supply_property ucs1002_props[] = {
+ POWER_SUPPLY_PROP_ONLINE,
+ POWER_SUPPLY_PROP_CHARGE_NOW,
+ POWER_SUPPLY_PROP_CURRENT_NOW,
+ POWER_SUPPLY_PROP_CURRENT_MAX,
+ POWER_SUPPLY_PROP_PRESENT, /* the presence of PED */
+ POWER_SUPPLY_PROP_MANUFACTURER,
+ POWER_SUPPLY_PROP_USB_TYPE,
+ POWER_SUPPLY_PROP_HEALTH,
+};
+
+static int ucs1002_get_online(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ unsigned int reg;
+ int ret;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®);
+ if (ret)
+ return ret;
+
+ val->intval = !!(reg & F_CHG_ACT);
+
+ return 0;
+}
+
+static int ucs1002_get_charge(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ /*
+ * To fit within 32 bits some values are rounded (uA/h)
+ *
+ * For Total Accumulated Charge Middle Low Byte register, addr
+ * 03h, byte 2
+ *
+ * B0: 0.01084 mA/h rounded to 11 uA/h
+ * B1: 0.02169 mA/h rounded to 22 uA/h
+ * B2: 0.04340 mA/h rounded to 43 uA/h
+ * B3: 0.08676 mA/h rounded to 87 uA/h
+ * B4: 0.17350 mA/h rounded to 173 uÁ/h
+ *
+ * For Total Accumulated Charge Low Byte register, addr 04h,
+ * byte 3
+ *
+ * B6: 0.00271 mA/h rounded to 3 uA/h
+ * B7: 0.005422 mA/h rounded to 5 uA/h
+ */
+ static const int bit_weights_uAh[BITS_PER_TYPE(u32)] = {
+ /*
+ * Bit corresponding to low byte (offset 0x04)
+ * B0 B1 B2 B3 B4 B5 B6 B7
+ */
+ 0, 0, 0, 0, 0, 0, 3, 5,
+ /*
+ * Bit corresponding to middle low byte (offset 0x03)
+ * B0 B1 B2 B3 B4 B5 B6 B7
+ */
+ 11, 22, 43, 87, 173, 347, 694, 1388,
+ /*
+ * Bit corresponding to middle high byte (offset 0x02)
+ * B0 B1 B2 B3 B4 B5 B6 B7
+ */
+ 2776, 5552, 11105, 22210, 44420, 88840, 177700, 355400,
+ /*
+ * Bit corresponding to high byte (offset 0x01)
+ * B0 B1 B2 B3 B4 B5 B6 B7
+ */
+ 710700, 1421000, 2843000, 5685000, 11371000, 22742000,
+ 45484000, 90968000,
+ };
+ unsigned long total_acc_charger;
+ unsigned int reg;
+ int i, ret;
+
+ ret = regmap_bulk_read(info->regmap, UCS1002_REG_TOTAL_ACC_CHARGE,
+ ®, sizeof(u32));
+ if (ret)
+ return ret;
+
+ total_acc_charger = be32_to_cpu(reg); /* BE as per offsets above */
+ val->intval = 0;
+
+ for_each_set_bit(i, &total_acc_charger, ARRAY_SIZE(bit_weights_uAh))
+ val->intval += bit_weights_uAh[i];
+
+ return 0;
+}
+
+static int ucs1002_get_current(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ /*
+ * The Current Measurement register stores the measured
+ * current value delivered to the portable device. The range
+ * is from 9.76 mA to 2.5 A.
+ */
+ static const int bit_weights_uA[BITS_PER_TYPE(u8)] = {
+ 9760, 19500, 39000, 78100, 156200, 312300, 624600, 1249300,
+ };
+ unsigned long current_measurement;
+ unsigned int reg;
+ int i, ret;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_CURRENT_MEASUREMENT, ®);
+ if (ret)
+ return ret;
+
+ current_measurement = reg;
+ val->intval = 0;
+
+ for_each_set_bit(i, ¤t_measurement, ARRAY_SIZE(bit_weights_uA))
+ val->intval += bit_weights_uA[i];
+
+ return 0;
+}
+
+/*
+ * The Current Limit register stores the maximum current used by the
+ * port switch. The range is from 500mA to 2.5 A.
+ */
+static const u32 ucs1002_current_limit_uA[] = {
+ 500000, 900000, 1000000, 1200000, 1500000, 1800000, 2000000, 2500000,
+};
+
+static int ucs1002_get_max_current(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ unsigned int reg;
+ int ret;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
+ if (ret)
+ return ret;
+
+ val->intval = ucs1002_current_limit_uA[reg & UCS1002_ILIM_SW_MASK];
+
+ return 0;
+}
+
+static int ucs1002_set_max_current(struct ucs1002_info *info, u32 val)
+{
+ unsigned int reg;
+ int ret, idx;
+
+ for (idx = 0; idx < ARRAY_SIZE(ucs1002_current_limit_uA); idx++) {
+ if (val == ucs1002_current_limit_uA[idx])
+ break;
+ }
+
+ if (idx == ARRAY_SIZE(ucs1002_current_limit_uA))
+ return -EINVAL;
+
+ ret = regmap_write(info->regmap, UCS1002_REG_ILIMIT, idx);
+ if (ret)
+ return ret;
+ /*
+ * Any current limit setting exceeding the one set via ILIM
+ * pin will be rejected, so we read out freshly changed limit
+ * to make sure that it took effect.
+ */
+ ret = regmap_read(info->regmap, UCS1002_REG_ILIMIT, ®);
+ if (ret)
+ return ret;
+
+ if (reg != idx)
+ return -EINVAL;
+
+ return 0;
+}
+
+static enum power_supply_usb_type ucs1002_usb_types[] = {
+ POWER_SUPPLY_USB_TYPE_PD,
+ POWER_SUPPLY_USB_TYPE_SDP,
+ POWER_SUPPLY_USB_TYPE_DCP,
+ POWER_SUPPLY_USB_TYPE_CDP,
+ POWER_SUPPLY_USB_TYPE_UNKNOWN,
+};
+
+static int ucs1002_set_usb_type(struct ucs1002_info *info, int val)
+{
+ unsigned int mode;
+
+ if (val >= ARRAY_SIZE(ucs1002_usb_types))
+ return -EINVAL;
+
+ switch (ucs1002_usb_types[val]) {
+ case POWER_SUPPLY_USB_TYPE_PD:
+ mode = V_SET_ACTIVE_MODE_DEDICATED;
+ break;
+ case POWER_SUPPLY_USB_TYPE_SDP:
+ mode = V_SET_ACTIVE_MODE_BC12_SDP;
+ break;
+ case POWER_SUPPLY_USB_TYPE_DCP:
+ mode = V_SET_ACTIVE_MODE_BC12_DCP;
+ break;
+ case POWER_SUPPLY_USB_TYPE_CDP:
+ mode = V_SET_ACTIVE_MODE_BC12_CDP;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
+ V_SET_ACTIVE_MODE_MASK, mode);
+}
+
+static int ucs1002_get_usb_type(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ enum power_supply_usb_type type;
+ unsigned int reg;
+ int ret;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®);
+ if (ret)
+ return ret;
+
+ switch (reg & F_ACTIVE_MODE_MASK) {
+ default:
+ type = POWER_SUPPLY_USB_TYPE_UNKNOWN;
+ break;
+ case F_ACTIVE_MODE_DEDICATED:
+ type = POWER_SUPPLY_USB_TYPE_PD;
+ break;
+ case F_ACTIVE_MODE_BC12_SDP:
+ type = POWER_SUPPLY_USB_TYPE_SDP;
+ break;
+ case F_ACTIVE_MODE_BC12_DCP:
+ type = POWER_SUPPLY_USB_TYPE_DCP;
+ break;
+ case F_ACTIVE_MODE_BC12_CDP:
+ type = POWER_SUPPLY_USB_TYPE_CDP;
+ break;
+ };
+
+ val->intval = type;
+
+ return 0;
+}
+
+static int ucs1002_get_health(struct ucs1002_info *info,
+ union power_supply_propval *val)
+{
+ unsigned int reg;
+ int ret, health;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_INTERRUPT_STATUS, ®);
+ if (ret)
+ return ret;
+
+ if (reg & F_TSD)
+ health = POWER_SUPPLY_HEALTH_OVERHEAT;
+ else if (reg & (F_OVER_VOLT | F_BACK_VOLT))
+ health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+ else if (reg & F_OVER_ILIM)
+ health = POWER_SUPPLY_HEALTH_OVERCURRENT;
+ else if (reg & (F_DISCHARGE_ERR | F_MIN_KEEP_OUT))
+ health = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+ else
+ health = POWER_SUPPLY_HEALTH_GOOD;
+
+ val->intval = health;
+
+ return 0;
+}
+
+static int ucs1002_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct ucs1002_info *info = power_supply_get_drvdata(psy);
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_ONLINE:
+ return ucs1002_get_online(info, val);
+ case POWER_SUPPLY_PROP_CHARGE_NOW:
+ return ucs1002_get_charge(info, val);
+ case POWER_SUPPLY_PROP_CURRENT_NOW:
+ return ucs1002_get_current(info, val);
+ case POWER_SUPPLY_PROP_CURRENT_MAX:
+ return ucs1002_get_max_current(info, val);
+ case POWER_SUPPLY_PROP_USB_TYPE:
+ return ucs1002_get_usb_type(info, val);
+ case POWER_SUPPLY_PROP_HEALTH:
+ return ucs1002_get_health(info, val);
+ case POWER_SUPPLY_PROP_PRESENT:
+ val->intval = info->present;
+ return 0;
+ case POWER_SUPPLY_PROP_MANUFACTURER:
+ val->strval = UCS1002_MANUFACTURER;
+ return 0;
+ default:
+ return -EINVAL;
+ }
+}
+
+static int ucs1002_set_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ const union power_supply_propval *val)
+{
+ struct ucs1002_info *info = power_supply_get_drvdata(psy);
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_CURRENT_MAX:
+ return ucs1002_set_max_current(info, val->intval);
+ case POWER_SUPPLY_PROP_USB_TYPE:
+ return ucs1002_set_usb_type(info, val->intval);
+ default:
+ return -EINVAL;
+ }
+}
+
+static int ucs1002_property_is_writeable(struct power_supply *psy,
+ enum power_supply_property psp)
+{
+ switch (psp) {
+ case POWER_SUPPLY_PROP_CURRENT_MAX:
+ case POWER_SUPPLY_PROP_USB_TYPE:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static const struct power_supply_desc ucs1002_charger_desc = {
+ .name = "ucs1002",
+ .type = POWER_SUPPLY_TYPE_USB,
+ .usb_types = ucs1002_usb_types,
+ .num_usb_types = ARRAY_SIZE(ucs1002_usb_types),
+ .get_property = ucs1002_get_property,
+ .set_property = ucs1002_set_property,
+ .property_is_writeable = ucs1002_property_is_writeable,
+ .properties = ucs1002_props,
+ .num_properties = ARRAY_SIZE(ucs1002_props),
+};
+
+static irqreturn_t ucs1002_charger_irq(int irq, void *data)
+{
+ int ret, regval;
+ bool present;
+ struct ucs1002_info *info = data;
+
+ present = info->present;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_OTHER_STATUS, ®val);
+ if (ret)
+ return IRQ_HANDLED;
+
+ /* update attached status */
+ info->present = regval & F_ADET_PIN;
+
+ /* notify the change */
+ if (present != info->present)
+ power_supply_changed(info->charger);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t ucs1002_alert_irq(int irq, void *data)
+{
+ struct ucs1002_info *info = data;
+
+ power_supply_changed(info->charger);
+
+ return IRQ_HANDLED;
+}
+
+static const struct regulator_ops ucs1002_regulator_ops = {
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+};
+
+static const struct regulator_desc ucs1002_regulator_descriptor = {
+ .name = "ucs1002-vbus",
+ .ops = &ucs1002_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .enable_reg = UCS1002_REG_SWITCH_CFG,
+ .enable_mask = F_PWR_EN_SET,
+ .enable_val = F_PWR_EN_SET,
+ .fixed_uV = 5000000,
+ .n_voltages = 1,
+};
+
+static int ucs1002_probe(struct i2c_client *client,
+ const struct i2c_device_id *dev_id)
+{
+ struct device *dev = &client->dev;
+ struct power_supply_config charger_config = {};
+ const struct regmap_config regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ };
+ struct regulator_config regulator_config = {};
+ int irq_a_det, irq_alert, ret;
+ struct regulator_dev *rdev;
+ struct ucs1002_info *info;
+ unsigned int regval;
+
+ info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ info->regmap = devm_regmap_init_i2c(client, ®map_config);
+ ret = PTR_ERR_OR_ZERO(info->charger);
+ if (ret) {
+ dev_err(dev, "Regmap initialization failed: %d\n", ret);
+ return ret;
+ }
+
+ info->client = client;
+
+ irq_a_det = of_irq_get_byname(dev->of_node, "a_det");
+ irq_alert = of_irq_get_byname(dev->of_node, "alert");
+
+ charger_config.of_node = dev->of_node;
+ charger_config.drv_data = info;
+
+ ret = regmap_read(info->regmap, UCS1002_REG_PRODUCT_ID, ®val);
+ if (ret) {
+ dev_err(dev, "Failed to read product ID: %d\n", ret);
+ return ret;
+ }
+
+ if (regval != UCS1002_PRODUCT_ID) {
+ dev_err(dev,
+ "Product ID does not match (0x%02x != 0x%02x)\n",
+ regval, UCS1002_PRODUCT_ID);
+ return -ENODEV;
+ }
+
+ /* Enable charge rationing by default */
+ ret = regmap_update_bits(info->regmap, UCS1002_REG_GENERAL_CFG,
+ F_RATION_EN, F_RATION_EN);
+ if (ret) {
+ dev_err(dev, "Failed to read general config: %d\n", ret);
+ return ret;
+ }
+
+ /*
+ * Ignore the M1, M2, PWR_EN, and EM_EN pin states. Set active
+ * mode selection to BC1.2 CDP.
+ */
+ ret = regmap_update_bits(info->regmap, UCS1002_REG_SWITCH_CFG,
+ V_SET_ACTIVE_MODE_MASK,
+ V_SET_ACTIVE_MODE_BC12_CDP);
+ if (ret) {
+ dev_err(dev, "Failed to configure default mode: %d\n", ret);
+ return ret;
+ }
+ /*
+ * Be safe and set initial current limit to 500mA
+ */
+ ret = ucs1002_set_max_current(info, 500000);
+ if (ret) {
+ dev_err(dev, "Failed to set max current default: %d\n", ret);
+ return ret;
+ }
+
+ info->charger = devm_power_supply_register(dev, &ucs1002_charger_desc,
+ &charger_config);
+ ret = PTR_ERR_OR_ZERO(info->charger);
+ if (ret) {
+ dev_err(dev, "Failed to register power supply: %d\n", ret);
+ return ret;
+ }
+
+ ret = regmap_read(info->regmap, UCS1002_REG_PIN_STATUS, ®val);
+ if (ret) {
+ dev_err(dev, "Failed to read pin status: %d\n", ret);
+ return ret;
+ }
+
+ info->regulator_descriptor =
+ devm_kmemdup(dev, &ucs1002_regulator_descriptor,
+ sizeof(ucs1002_regulator_descriptor),
+ GFP_KERNEL);
+ if (!info->regulator_descriptor)
+ return -ENOMEM;
+
+ info->regulator_descriptor->enable_is_inverted = !(regval & F_SEL_PIN);
+
+ regulator_config.dev = dev;
+ regulator_config.of_node = dev->of_node;
+ regulator_config.regmap = info->regmap;
+
+ rdev = devm_regulator_register(dev, info->regulator_descriptor,
+ ®ulator_config);
+ ret = PTR_ERR_OR_ZERO(info->charger);
+ if (ret) {
+ dev_err(dev, "Failed to register VBUS regulator: %d\n", ret);
+ return ret;
+ }
+
+ if (irq_a_det > 0) {
+ ret = devm_request_threaded_irq(dev, irq_a_det, NULL,
+ ucs1002_charger_irq,
+ IRQF_ONESHOT,
+ "ucs1002-a_det", info);
+ if (ret) {
+ dev_err(dev, "Failed to request A_DET threaded irq: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
+ if (irq_alert > 0) {
+ ret = devm_request_threaded_irq(dev, irq_alert, NULL,
+ ucs1002_alert_irq,
+ IRQF_ONESHOT,
+ "ucs1002-alert", info);
+ if (ret) {
+ dev_err(dev, "Failed to request ALERT threaded irq: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static const struct of_device_id ucs1002_of_match[] = {
+ { .compatible = "microchip,ucs1002", },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ucs1002_of_match);
+
+static struct i2c_driver ucs1002_driver = {
+ .driver = {
+ .name = "ucs1002",
+ .of_match_table = ucs1002_of_match,
+ },
+ .probe = ucs1002_probe,
+};
+module_i2c_driver(ucs1002_driver);
+
+MODULE_DESCRIPTION("Microchip UCS1002 Programmable USB Port Power Controller");
+MODULE_AUTHOR("Enric Balletbo Serra <enric.balletbo@collabora.com>");
+MODULE_AUTHOR("Andrey Smirnov <andrew.smirnov@gmail.com>");
+MODULE_LICENSE("GPL");
--
2.20.1
^ permalink raw reply related [flat|nested] 6+ messages in thread