[PATCH v2 00/11] enable usb support on rk356x

[PATCH v2 00/11] enable usb support on rk356x

[Peter Geis]

Good Morning,

This is my patch series that I have maintained out of tree until the
combophy driver landed.

Patch 1 fixes the grf dt binding from the combophy merge.
Patches 2 and 3 add the dt bindings for the grf changes necessary for
this series.
Patch 4 adds support to the grf driver to set the rk3566 otg clock
source.
Patch 5 is a downstream patch ported forward to shut down the usb3 clock
when the controller is operating in usb2 mode.
Patches 6, 7, and 8 clean up the dwc3-of-simple driver, allow the use of
of-match-data, and add the compatible for the rk3568.
Patch 9 adds the dwc3 nodes to the rk356x device tree includes.
Patch 10 enables the dwc3 nodes on the Quartz64 Model A.
Patch 11 enables the dwc3 nodes on the rk3568-evb.

Please review and apply.

Very Respectfully,
Peter Geis

Changelog:
v2:
- Add a dt-bindings fix for grf.yaml
- Unify the reset names.
- Constrain the force usb2 clock dwc3 patch to only supported variants of
the ip.
- Change dwc3-of-simple to support of-match-data.
- Drop the PCLK-PIPE clk.
- Rename the usb nodes to be more friendly.
- Add the rk3568-evb enable patch.

Bin Yang (1):
  usb: dwc3: core: do not use 3.0 clock when operating in 2.0 mode

Michael Riesch (1):
  arm64: dts: rockchip: add usb3 support to rk3568-evb1-v10

Peter Geis (9):
  dt-bindings: soc: grf: fix rk3568 usb definitions
  dt-bindings: soc: grf: add rk3566-pipe-grf compatible
  dt-bindings: usb: dwc3: add description for rk3568
  soc: rockchip: set dwc3 clock for rk3566
  usb: dwc3: reorder dwc-of-simple compatibles
  usb: dwc3: convert dwc3-of-simple to use match-data
  usb: dwc3: add rk3568 dwc3 support
  arm64: dts: rockchip: add rk356x dwc3 usb3 nodes
  arm64: dts: rockchip: enable dwc3 on quartz64-a

 .../devicetree/bindings/soc/rockchip/grf.yaml |  5 +-
 .../bindings/usb/rockchip,dwc3.yaml           |  2 +
 .../boot/dts/rockchip/rk3566-quartz64-a.dts   | 37 +++++++++++++++
 arch/arm64/boot/dts/rockchip/rk3566.dtsi      | 12 +++++
 .../boot/dts/rockchip/rk3568-evb1-v10.dts     | 46 +++++++++++++++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi      |  9 ++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi      | 45 +++++++++++++++++-
 drivers/soc/rockchip/grf.c                    | 17 +++++++
 drivers/usb/dwc3/core.c                       |  5 ++
 drivers/usb/dwc3/core.h                       |  1 +
 drivers/usb/dwc3/dwc3-of-simple.c             | 43 +++++++++++++----
 11 files changed, 210 insertions(+), 12 deletions(-)

-- 
2.25.1

[PATCH v2 01/11] dt-bindings: soc: grf: fix rk3568 usb definitions

[Peter Geis]

The rockchip,rk3568-pipe-grf and rockchip,rk3568-pipe-phy-grf
compatibles were incorrectly assigned to the syscon, simple-mfd
enumeration, vice only the syscon enumeration.
This leads a dtbs_check failure.

Move these to the syscon enumeration.

Fixes: b3df807e1fb0 ("dt-bindings: soc: grf: add naneng combo phy register compatible")

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
index 072318fcd57b..5079e9d24af6 100644
--- a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
+++ b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
@@ -15,6 +15,8 @@ properties:
       - items:
           - enum:
               - rockchip,rk3288-sgrf
+              - rockchip,rk3568-pipe-grf
+              - rockchip,rk3568-pipe-phy-grf
               - rockchip,rk3568-usb2phy-grf
               - rockchip,rv1108-usbgrf
           - const: syscon
@@ -39,8 +41,6 @@ properties:
               - rockchip,rk3399-grf
               - rockchip,rk3399-pmugrf
               - rockchip,rk3568-grf
-              - rockchip,rk3568-pipe-grf
-              - rockchip,rk3568-pipe-phy-grf
               - rockchip,rk3568-pmugrf
               - rockchip,rv1108-grf
               - rockchip,rv1108-pmugrf
-- 
2.25.1

[PATCH v2 02/11] dt-bindings: soc: grf: add rk3566-pipe-grf compatible

[Peter Geis]

The rk3566 requires special handling for the dwc3-otg clock in order for
the port to function correctly.
Add a binding for the rk3566-pipe-grf so we can handle setup with the
grf driver.

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
index 5079e9d24af6..75a2b8bb25fb 100644
--- a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
+++ b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
@@ -15,6 +15,7 @@ properties:
       - items:
           - enum:
               - rockchip,rk3288-sgrf
+              - rockchip,rk3566-pipe-grf
               - rockchip,rk3568-pipe-grf
               - rockchip,rk3568-pipe-phy-grf
               - rockchip,rk3568-usb2phy-grf
-- 
2.25.1

[PATCH v2 03/11] dt-bindings: usb: dwc3: add description for rk3568

[Peter Geis]

The rk3568 dwc3 controllers are backwards compatible with the rk3399.
Add the device tree description for it.

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml
index 04077f2d7faf..b3798d94d2fd 100644
--- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml
+++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml
@@ -30,6 +30,7 @@ select:
         enum:
           - rockchip,rk3328-dwc3
           - rockchip,rk3399-dwc3
+          - rockchip,rk3568-dwc3
   required:
     - compatible
 
@@ -39,6 +40,7 @@ properties:
       - enum:
           - rockchip,rk3328-dwc3
           - rockchip,rk3399-dwc3
+          - rockchip,rk3568-dwc3
       - const: snps,dwc3
 
   reg:
-- 
2.25.1

[PATCH v2 04/11] soc: rockchip: set dwc3 clock for rk3566

[Peter Geis]

The rk3566 dwc3 otg port clock is unavailable at boot, as it defaults to
the combophy as the clock source. As combophy0 doesn't exist on rk3566,
we need to set the clock source to the usb2 phy instead.

Add handling to the grf driver to handle this on boot.

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 drivers/soc/rockchip/grf.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/drivers/soc/rockchip/grf.c b/drivers/soc/rockchip/grf.c
index 494cf2b5bf7b..384461b70684 100644
--- a/drivers/soc/rockchip/grf.c
+++ b/drivers/soc/rockchip/grf.c
@@ -108,6 +108,20 @@ static const struct rockchip_grf_info rk3399_grf __initconst = {
 	.num_values = ARRAY_SIZE(rk3399_defaults),
 };
 
+#define RK3566_GRF_USB3OTG0_CON1	0x0104
+
+static const struct rockchip_grf_value rk3566_defaults[] __initconst = {
+	{ "usb3otg port switch", RK3566_GRF_USB3OTG0_CON1, HIWORD_UPDATE(0, 1, 12) },
+	{ "usb3otg clock switch", RK3566_GRF_USB3OTG0_CON1, HIWORD_UPDATE(1, 1, 7) },
+	{ "usb3otg disable usb3", RK3566_GRF_USB3OTG0_CON1, HIWORD_UPDATE(1, 1, 0) },
+};
+
+static const struct rockchip_grf_info rk3566_pipegrf __initconst = {
+	.values = rk3566_defaults,
+	.num_values = ARRAY_SIZE(rk3566_defaults),
+};
+
+
 static const struct of_device_id rockchip_grf_dt_match[] __initconst = {
 	{
 		.compatible = "rockchip,rk3036-grf",
@@ -130,6 +144,9 @@ static const struct of_device_id rockchip_grf_dt_match[] __initconst = {
 	}, {
 		.compatible = "rockchip,rk3399-grf",
 		.data = (void *)&rk3399_grf,
+	}, {
+		.compatible = "rockchip,rk3566-pipe-grf",
+		.data = (void *)&rk3566_pipegrf,
 	},
 	{ /* sentinel */ },
 };
-- 
2.25.1

[PATCH v2 05/11] usb: dwc3: core: do not use 3.0 clock when operating in 2.0 mode

[Peter Geis]

From: Bin Yang <yangbin@rock-chips.com>

In the 3.0 device core, if the core is programmed to operate in
2.0 only, then setting the GUCTL1.DEV_FORCE_20_CLK_FOR_30_CLK makes
the internal 2.0(utmi/ulpi) clock to be routed as the 3.0 (pipe)
clock. Enabling this feature allows the pipe3 clock to be not-running
when forcibly operating in 2.0 device mode.

Signed-off-by: Bin Yang <yangbin@rock-chips.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 drivers/usb/dwc3/core.c | 5 +++++
 drivers/usb/dwc3/core.h | 1 +
 2 files changed, 6 insertions(+)

diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 18adddfba3da..416d83a055fe 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -1167,6 +1167,11 @@ static int dwc3_core_init(struct dwc3 *dwc)
 		if (dwc->parkmode_disable_ss_quirk)
 			reg |= DWC3_GUCTL1_PARKMODE_DISABLE_SS;
 
+		if (DWC3_VER_IS_WITHIN(DWC3, 290A, ANY) &&
+		    (dwc->maximum_speed == USB_SPEED_HIGH ||
+		     dwc->maximum_speed == USB_SPEED_FULL))
+			reg |= DWC3_GUCTL1_DEV_FORCE_20_CLK_FOR_30_CLK;
+
 		dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
 	}
 
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index eb9c1efced05..ea3ca04406bb 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -259,6 +259,7 @@
 /* Global User Control 1 Register */
 #define DWC3_GUCTL1_DEV_DECOUPLE_L1L2_EVT	BIT(31)
 #define DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS	BIT(28)
+#define DWC3_GUCTL1_DEV_FORCE_20_CLK_FOR_30_CLK	BIT(26)
 #define DWC3_GUCTL1_DEV_L1_EXIT_BY_HW		BIT(24)
 #define DWC3_GUCTL1_PARKMODE_DISABLE_SS		BIT(17)
 
-- 
2.25.1

[PATCH v2 06/11] usb: dwc3: reorder dwc-of-simple compatibles

[Peter Geis]

The dwc3-of-simple driver is getting rather disorganized with the new
inclusions.
Reorder the dwc3-of-simple compatibles to be alphabetical.

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 drivers/usb/dwc3/dwc3-of-simple.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-of-simple.c
index 71fd620c5161..9dc6295df6b1 100644
--- a/drivers/usb/dwc3/dwc3-of-simple.c
+++ b/drivers/usb/dwc3/dwc3-of-simple.c
@@ -171,12 +171,12 @@ static const struct dev_pm_ops dwc3_of_simple_dev_pm_ops = {
 };
 
 static const struct of_device_id of_dwc3_simple_match[] = {
-	{ .compatible = "rockchip,rk3399-dwc3" },
-	{ .compatible = "cavium,octeon-7130-usb-uctl" },
-	{ .compatible = "sprd,sc9860-dwc3" },
 	{ .compatible = "allwinner,sun50i-h6-dwc3" },
+	{ .compatible = "cavium,octeon-7130-usb-uctl" },
 	{ .compatible = "hisilicon,hi3670-dwc3" },
 	{ .compatible = "intel,keembay-dwc3" },
+	{ .compatible = "rockchip,rk3399-dwc3" },
+	{ .compatible = "sprd,sc9860-dwc3" },
 	{ /* Sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, of_dwc3_simple_match);
-- 
2.25.1

[PATCH v2 07/11] usb: dwc3: convert dwc3-of-simple to use match-data

[Peter Geis]

The upcoming support for rk3568 will reuse data from rk3399.
Instead of adding a bunch of of_device_is_compatible as we add support
for new devices, lets get ahead of the problem and use of_match_data
instead.

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 drivers/usb/dwc3/dwc3-of-simple.c | 39 ++++++++++++++++++++++++-------
 1 file changed, 30 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-of-simple.c
index 9dc6295df6b1..57ba9427ad74 100644
--- a/drivers/usb/dwc3/dwc3-of-simple.c
+++ b/drivers/usb/dwc3/dwc3-of-simple.c
@@ -30,12 +30,16 @@ struct dwc3_of_simple {
 	bool			need_reset;
 };
 
+struct dwc3_of_simple_data {
+	bool			need_reset;
+};
+
 static int dwc3_of_simple_probe(struct platform_device *pdev)
 {
 	struct dwc3_of_simple	*simple;
 	struct device		*dev = &pdev->dev;
 	struct device_node	*np = dev->of_node;
-
+	const struct dwc3_of_simple_data *data = of_device_get_match_data(dev);
 	int			ret;
 
 	simple = devm_kzalloc(dev, sizeof(*simple), GFP_KERNEL);
@@ -49,8 +53,8 @@ static int dwc3_of_simple_probe(struct platform_device *pdev)
 	 * Some controllers need to toggle the usb3-otg reset before trying to
 	 * initialize the PHY, otherwise the PHY times out.
 	 */
-	if (of_device_is_compatible(np, "rockchip,rk3399-dwc3"))
-		simple->need_reset = true;
+	if (data->need_reset)
+		simple->need_reset = data->need_reset;
 
 	simple->resets = of_reset_control_array_get(np, false, true,
 						    true);
@@ -170,13 +174,30 @@ static const struct dev_pm_ops dwc3_of_simple_dev_pm_ops = {
 			dwc3_of_simple_runtime_resume, NULL)
 };
 
+static const struct dwc3_of_simple_data dwc3_of_simple_data_rk3399 = {
+	.need_reset = true,
+};
+
 static const struct of_device_id of_dwc3_simple_match[] = {
-	{ .compatible = "allwinner,sun50i-h6-dwc3" },
-	{ .compatible = "cavium,octeon-7130-usb-uctl" },
-	{ .compatible = "hisilicon,hi3670-dwc3" },
-	{ .compatible = "intel,keembay-dwc3" },
-	{ .compatible = "rockchip,rk3399-dwc3" },
-	{ .compatible = "sprd,sc9860-dwc3" },
+	{
+		.compatible = "allwinner,sun50i-h6-dwc3",
+	},
+	{
+		.compatible = "cavium,octeon-7130-usb-uctl",
+	},
+	{
+		.compatible = "hisilicon,hi3670-dwc3",
+	},
+	{
+		.compatible = "intel,keembay-dwc3",
+	},
+	{
+		.compatible = "rockchip,rk3399-dwc3",
+		.data = &dwc3_of_simple_data_rk3399,
+	},
+	{
+		.compatible = "sprd,sc9860-dwc3",
+	},
 	{ /* Sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, of_dwc3_simple_match);
-- 
2.25.1

[PATCH v2 08/11] usb: dwc3: add rk3568 dwc3 support

[Peter Geis]

The rk3568 dwc3 controller is backwards compatible with the rk3399 dwc3
controller.
Add support for it to the dwc3-of-simple driver.

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 drivers/usb/dwc3/dwc3-of-simple.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-of-simple.c
index 57ba9427ad74..d9d1c5bfac3f 100644
--- a/drivers/usb/dwc3/dwc3-of-simple.c
+++ b/drivers/usb/dwc3/dwc3-of-simple.c
@@ -195,6 +195,10 @@ static const struct of_device_id of_dwc3_simple_match[] = {
 		.compatible = "rockchip,rk3399-dwc3",
 		.data = &dwc3_of_simple_data_rk3399,
 	},
+	{
+		.compatible = "rockchip,rk3568-dwc3",
+		.data = &dwc3_of_simple_data_rk3399,
+	},
 	{
 		.compatible = "sprd,sc9860-dwc3",
 	},
-- 
2.25.1

[PATCH v2 09/11] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

[Peter Geis]

Add the dwc3 device nodes to the rk356x device trees.
The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable
dwc3 host controller.
The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable
dwc3 host controller.

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3566.dtsi | 12 +++++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 +++++
 arch/arm64/boot/dts/rockchip/rk356x.dtsi | 45 +++++++++++++++++++++++-
 3 files changed, 65 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3566.dtsi b/arch/arm64/boot/dts/rockchip/rk3566.dtsi
index 3839eef5e4f7..a57eb68faba2 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3566.dtsi
@@ -6,6 +6,10 @@ / {
 	compatible = "rockchip,rk3566";
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3566-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;
@@ -18,3 +22,11 @@ power-domain@RK3568_PD_PIPE {
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>;
+	phy-names = "usb2-phy";
+	extcon = <&usb2phy0>;
+	maximum-speed = "high-speed";
+	snps,dis_u2_susphy_quirk;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3568.dtsi b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
index 5b0f528d6818..8ba9334f9753 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
@@ -99,6 +99,10 @@ opp-1992000000 {
 	};
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;
@@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+	phy-names = "usb2-phy", "usb3-phy";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
index 7cdef800cb3c..b22e5a514ad7 100644
--- a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
@@ -230,6 +230,50 @@ scmi_shmem: sram@0 {
 		};
 	};
 
+	usb_host0_xhci: usb@fcc00000 {
+		compatible = "rockchip,rk3568-dwc3", "snps,dwc3";
+		reg = <0x0 0xfcc00000 0x0 0x400000>;
+		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
+			 <&cru ACLK_USB3OTG0>;
+		clock-names = "ref_clk", "suspend_clk",
+			      "bus_clk";
+		dr_mode = "host";
+		phy_type = "utmi_wide";
+		power-domains = <&power RK3568_PD_PIPE>;
+		resets = <&cru SRST_USB3OTG0>;
+		reset-names = "usb3-otg";
+		snps,dis_enblslpm_quirk;
+		snps,dis-u2-freeclk-exists-quirk;
+		snps,dis-del-phy-power-chg-quirk;
+		snps,dis-tx-ipgap-linecheck-quirk;
+		snps,xhci-trb-ent-quirk;
+		status = "disabled";
+	};
+
+	usb_host1_xhci: usb@fd000000 {
+		compatible = "rockchip,rk3568-dwc3", "snps,dwc3";
+		reg = <0x0 0xfd000000 0x0 0x400000>;
+		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
+			 <&cru ACLK_USB3OTG1>;
+		clock-names = "ref_clk", "suspend_clk",
+			      "bus_clk";
+		dr_mode = "host";
+		phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
+		phy-names = "usb2-phy", "usb3-phy";
+		phy_type = "utmi_wide";
+		power-domains = <&power RK3568_PD_PIPE>;
+		resets = <&cru SRST_USB3OTG1>;
+		reset-names = "usb3-otg";
+		snps,dis_enblslpm_quirk;
+		snps,dis-u2-freeclk-exists-quirk;
+		snps,dis_u2_susphy_quirk;
+		snps,dis-del-phy-power-chg-quirk;
+		snps,dis-tx-ipgap-linecheck-quirk;
+		status = "disabled";
+	};
+
 	gic: interrupt-controller@fd400000 {
 		compatible = "arm,gic-v3";
 		reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
@@ -297,7 +341,6 @@ pmu_io_domains: io-domains {
 	};
 
 	pipegrf: syscon@fdc50000 {
-		compatible = "rockchip,rk3568-pipe-grf", "syscon";
 		reg = <0x0 0xfdc50000 0x0 0x1000>;
 	};
 
-- 
2.25.1

[PATCH v2 10/11] arm64: dts: rockchip: enable dwc3 on quartz64-a

[Peter Geis]

The quartz64 model a has support for both the dwc3 otg port and the dwc3
host port. Add the otg power supply and dwc3 nodes to the device tree to
enable support for these.

Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 .../boot/dts/rockchip/rk3566-quartz64-a.dts   | 37 +++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
index dd7f4b9b686b..141a433429b5 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
@@ -151,6 +151,16 @@ vcc5v0_usb20_host: vcc5v0_usb20_host {
 		vin-supply = <&vcc5v0_usb>;
 	};
 
+	vcc5v0_usb20_otg: vcc5v0_usb20_otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+		regulator-name = "vcc5v0_usb20_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dcdc_boost>;
+	};
+
 	vcc3v3_sd: vcc3v3_sd {
 		compatible = "regulator-fixed";
 		enable-active-low;
@@ -187,6 +197,10 @@ vcc_wl: vcc_wl {
 	};
 };
 
+&combphy1 {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&vdd_cpu>;
 };
@@ -672,6 +686,29 @@ &usb_host1_ohci {
 	status = "okay";
 };
 
+&usb_host0_xhci {
+	status = "okay";
+};
+
+/* usb3 controller is muxed with sata1 */
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb20_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb20_otg>;
+	status = "okay";
+};
+
 &usb2phy1 {
 	status = "okay";
 };
-- 
2.25.1

[PATCH v2 11/11] arm64: dts: rockchip: add usb3 support to rk3568-evb1-v10

[Peter Geis]

From: Michael Riesch <michael.riesch@wolfvision.net>

The Rockchip RK3568 EVB1 features one USB 3.0 device-only
(USB 2.0 OTG) port and one USB 3.0 host-only port.
Activate the USB 3.0 controller nodes and phy nodes in the
device tree.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
 .../boot/dts/rockchip/rk3568-evb1-v10.dts     | 46 +++++++++++++++++++
 1 file changed, 46 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
index a794a0ea5c70..622be8be9813 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
@@ -103,6 +103,18 @@ vcc5v0_usb_host: vcc5v0-usb-host {
 		vin-supply = <&vcc5v0_usb>;
 	};
 
+	vcc5v0_usb_otg: vcc5v0-usb-otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
 	vcc3v3_lcd0_n: vcc3v3-lcd0-n {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3_lcd0_n";
@@ -136,6 +148,14 @@ regulator-state-mem {
 	};
 };
 
+&combphy0 {
+	status = "okay";
+};
+
+&combphy1 {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&vdd_cpu>;
 };
@@ -507,6 +527,9 @@ usb {
 		vcc5v0_usb_host_en: vcc5v0_usb_host_en {
 			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
+		vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
 	};
 };
 
@@ -568,6 +591,11 @@ &usb_host0_ohci {
 	status = "okay";
 };
 
+&usb_host0_xhci {
+	extcon = <&usb2phy0>;
+	status = "okay";
+};
+
 &usb_host1_ehci {
 	status = "okay";
 };
@@ -576,6 +604,24 @@ &usb_host1_ohci {
 	status = "okay";
 };
 
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	vbus-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
 &usb2phy1 {
 	status = "okay";
 };
-- 
2.25.1

Re: [PATCH v2 08/11] usb: dwc3: add rk3568 dwc3 support

[Johan Jonker]

Hi Peter,

See comments by rob+dt:

https://lore.kernel.org/linux-rockchip/CAL_JsqJwNdUfoYM8SZmOgMG9iAyZkJ4-kzjjiDDm_mdmghTEOA@mail.gmail.com/

> Presumably you are getting lucky here (with link order). The kernel
> has no logic to decide which driver to bind to if there are 2 matching
> drivers.

Due to the fall back string you make a mess with two drivers.
Don't use dwc3-of-simple.c
(only for rk3399 and legacy support. Not for new SoCs),
because core.c has now reset support.
You are creating a race which driver get probed first.
Handle your quirks in core.

Johan

On 2/26/22 19:41, Peter Geis wrote:
> The rk3568 dwc3 controller is backwards compatible with the rk3399 dwc3
> controller.
> Add support for it to the dwc3-of-simple driver.
> 
> Signed-off-by: Peter Geis <pgwipeout@gmail.com>
> ---
>  drivers/usb/dwc3/dwc3-of-simple.c | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-of-simple.c
> index 57ba9427ad74..d9d1c5bfac3f 100644
> --- a/drivers/usb/dwc3/dwc3-of-simple.c
> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
> @@ -195,6 +195,10 @@ static const struct of_device_id of_dwc3_simple_match[] = {
>  		.compatible = "rockchip,rk3399-dwc3",
>  		.data = &dwc3_of_simple_data_rk3399,
>  	},
> +	{
> +		.compatible = "rockchip,rk3568-dwc3",
> +		.data = &dwc3_of_simple_data_rk3399,
> +	},
>  	{
>  		.compatible = "sprd,sc9860-dwc3",
>  	},

Re: [PATCH v2 09/11] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

[Johan Jonker]

On 2/26/22 19:41, Peter Geis wrote:
> Add the dwc3 device nodes to the rk356x device trees.
> The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable
> dwc3 host controller.
> The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable
> dwc3 host controller.
> 
> Signed-off-by: Peter Geis <pgwipeout@gmail.com>
> ---
>  arch/arm64/boot/dts/rockchip/rk3566.dtsi | 12 +++++++
>  arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 +++++
>  arch/arm64/boot/dts/rockchip/rk356x.dtsi | 45 +++++++++++++++++++++++-
>  3 files changed, 65 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3566.dtsi b/arch/arm64/boot/dts/rockchip/rk3566.dtsi
> index 3839eef5e4f7..a57eb68faba2 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3566.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3566.dtsi
> @@ -6,6 +6,10 @@ / {
>  	compatible = "rockchip,rk3566";
>  };
>  
> +&pipegrf {
> +	compatible = "rockchip,rk3566-pipe-grf", "syscon";
> +};
> +
>  &power {
>  	power-domain@RK3568_PD_PIPE {
>  		reg = <RK3568_PD_PIPE>;
> @@ -18,3 +22,11 @@ power-domain@RK3568_PD_PIPE {
>  		#power-domain-cells = <0>;
>  	};
>  };
> +
> +&usb_host0_xhci {
> +	phys = <&usb2phy0_otg>;
> +	phy-names = "usb2-phy";
> +	extcon = <&usb2phy0>;
> +	maximum-speed = "high-speed";
> +	snps,dis_u2_susphy_quirk;
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3568.dtsi b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
> index 5b0f528d6818..8ba9334f9753 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3568.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
> @@ -99,6 +99,10 @@ opp-1992000000 {
>  	};
>  };
>  
> +&pipegrf {
> +	compatible = "rockchip,rk3568-pipe-grf", "syscon";
> +};
> +
>  &power {
>  	power-domain@RK3568_PD_PIPE {
>  		reg = <RK3568_PD_PIPE>;
> @@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
>  		#power-domain-cells = <0>;
>  	};
>  };
> +
> +&usb_host0_xhci {
> +	phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
> +	phy-names = "usb2-phy", "usb3-phy";
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> index 7cdef800cb3c..b22e5a514ad7 100644
> --- a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> @@ -230,6 +230,50 @@ scmi_shmem: sram@0 {
>  		};
>  	};
>  
> +	usb_host0_xhci: usb@fcc00000 {
> +		compatible = "rockchip,rk3568-dwc3", "snps,dwc3";
> +		reg = <0x0 0xfcc00000 0x0 0x400000>;
> +		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
> +			 <&cru ACLK_USB3OTG0>;
> +		clock-names = "ref_clk", "suspend_clk",
> +			      "bus_clk";
> +		dr_mode = "host";
> +		phy_type = "utmi_wide";

> +		power-domains = <&power RK3568_PD_PIPE>;

When both usb_host0_xhci and usb_host1_xhci are connected to a usb2phy
and the combphy's disabled there's no PCLK_PIPE enabled.
Fix logic for RK3568_PD_PIPE by adding the USB3 clocks.


> +		resets = <&cru SRST_USB3OTG0>;

> +		reset-names = "usb3-otg";

remove

snps,dwc3.yaml only mentions the "resets" because
devm_reset_control_array_get_optional_shared is used.
reset-names is only a rk3399 legacy that I included due to the YAML
conversion.
With unevaluatedProperties now working "resets" also could be removed
from rockchip,dwc3.yaml I think.

https://github.com/torvalds/linux/commit/2f8e928408885dad5d8d6afefacb82100b6b62c7
Added properties for rk3399 are:
  power-domains
  resets
  reset-names

> +		snps,dis_enblslpm_quirk;
> +		snps,dis-u2-freeclk-exists-quirk;
> +		snps,dis-del-phy-power-chg-quirk;
> +		snps,dis-tx-ipgap-linecheck-quirk;

sort

> +		snps,xhci-trb-ent-quirk;

???

check snps,dwc3.yaml

> +		status = "disabled";
> +	};
> +
> +	usb_host1_xhci: usb@fd000000 {
> +		compatible = "rockchip,rk3568-dwc3", "snps,dwc3";
> +		reg = <0x0 0xfd000000 0x0 0x400000>;
> +		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
> +			 <&cru ACLK_USB3OTG1>;
> +		clock-names = "ref_clk", "suspend_clk",
> +			      "bus_clk";
> +		dr_mode = "host";
> +		phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
> +		phy-names = "usb2-phy", "usb3-phy";
> +		phy_type = "utmi_wide";

> +		power-domains = <&power RK3568_PD_PIPE>;

dito

> +		resets = <&cru SRST_USB3OTG1>;

> +		reset-names = "usb3-otg";

remove

> +		snps,dis_enblslpm_quirk;
> +		snps,dis-u2-freeclk-exists-quirk;
> +		snps,dis_u2_susphy_quirk;
> +		snps,dis-del-phy-power-chg-quirk;
> +		snps,dis-tx-ipgap-linecheck-quirk;

sort

> +		status = "disabled";
> +	};
> +
>  	gic: interrupt-controller@fd400000 {
>  		compatible = "arm,gic-v3";
>  		reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
> @@ -297,7 +341,6 @@ pmu_io_domains: io-domains {
>  	};
>  
>  	pipegrf: syscon@fdc50000 {
> -		compatible = "rockchip,rk3568-pipe-grf", "syscon";
>  		reg = <0x0 0xfdc50000 0x0 0x1000>;
>  	};
>  

Re: [PATCH v2 08/11] usb: dwc3: add rk3568 dwc3 support

[Peter Geis]

On Sat, Feb 26, 2022 at 4:43 PM Johan Jonker <jbx6244@gmail.com> wrote:
>
> Hi Peter,
>
> See comments by rob+dt:
>
> https://lore.kernel.org/linux-rockchip/CAL_JsqJwNdUfoYM8SZmOgMG9iAyZkJ4-kzjjiDDm_mdmghTEOA@mail.gmail.com/
>
> > Presumably you are getting lucky here (with link order). The kernel
> > has no logic to decide which driver to bind to if there are 2 matching
> > drivers.
>
> Due to the fall back string you make a mess with two drivers.
> Don't use dwc3-of-simple.c
> (only for rk3399 and legacy support. Not for new SoCs),
> because core.c has now reset support.
> You are creating a race which driver get probed first.
> Handle your quirks in core.

I finally understood what you were trying to get at here.
After some testing, it seems the core driver handles everything we need now.
This makes me want to revisit the rk3399 support.

Thanks!

>
> Johan
>
> On 2/26/22 19:41, Peter Geis wrote:
> > The rk3568 dwc3 controller is backwards compatible with the rk3399 dwc3
> > controller.
> > Add support for it to the dwc3-of-simple driver.
> >
> > Signed-off-by: Peter Geis <pgwipeout@gmail.com>
> > ---
> >  drivers/usb/dwc3/dwc3-of-simple.c | 4 ++++
> >  1 file changed, 4 insertions(+)
> >
> > diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-of-simple.c
> > index 57ba9427ad74..d9d1c5bfac3f 100644
> > --- a/drivers/usb/dwc3/dwc3-of-simple.c
> > +++ b/drivers/usb/dwc3/dwc3-of-simple.c
> > @@ -195,6 +195,10 @@ static const struct of_device_id of_dwc3_simple_match[] = {
> >               .compatible = "rockchip,rk3399-dwc3",
> >               .data = &dwc3_of_simple_data_rk3399,
> >       },
> > +     {
> > +             .compatible = "rockchip,rk3568-dwc3",
> > +             .data = &dwc3_of_simple_data_rk3399,
> > +     },
> >       {
> >               .compatible = "sprd,sc9860-dwc3",
> >       },

Re: [PATCH v2 09/11] arm64: dts: rockchip: add rk356x dwc3 usb3 nodes

[Peter Geis]

On Sat, Feb 26, 2022 at 6:01 PM Johan Jonker <jbx6244@gmail.com> wrote:
>
>
>
> On 2/26/22 19:41, Peter Geis wrote:
> > Add the dwc3 device nodes to the rk356x device trees.
> > The rk3566 has one usb2 capable dwc3 otg controller and one usb3 capable
> > dwc3 host controller.
> > The rk3568 has one usb3 capable dwc3 otg controller and one usb3 capable
> > dwc3 host controller.
> >
> > Signed-off-by: Peter Geis <pgwipeout@gmail.com>
> > ---
> >  arch/arm64/boot/dts/rockchip/rk3566.dtsi | 12 +++++++
> >  arch/arm64/boot/dts/rockchip/rk3568.dtsi |  9 +++++
> >  arch/arm64/boot/dts/rockchip/rk356x.dtsi | 45 +++++++++++++++++++++++-
> >  3 files changed, 65 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3566.dtsi b/arch/arm64/boot/dts/rockchip/rk3566.dtsi
> > index 3839eef5e4f7..a57eb68faba2 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3566.dtsi
> > +++ b/arch/arm64/boot/dts/rockchip/rk3566.dtsi
> > @@ -6,6 +6,10 @@ / {
> >       compatible = "rockchip,rk3566";
> >  };
> >
> > +&pipegrf {
> > +     compatible = "rockchip,rk3566-pipe-grf", "syscon";
> > +};
> > +
> >  &power {
> >       power-domain@RK3568_PD_PIPE {
> >               reg = <RK3568_PD_PIPE>;
> > @@ -18,3 +22,11 @@ power-domain@RK3568_PD_PIPE {
> >               #power-domain-cells = <0>;
> >       };
> >  };
> > +
> > +&usb_host0_xhci {
> > +     phys = <&usb2phy0_otg>;
> > +     phy-names = "usb2-phy";
> > +     extcon = <&usb2phy0>;
> > +     maximum-speed = "high-speed";
> > +     snps,dis_u2_susphy_quirk;
> > +};
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3568.dtsi b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
> > index 5b0f528d6818..8ba9334f9753 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3568.dtsi
> > +++ b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
> > @@ -99,6 +99,10 @@ opp-1992000000 {
> >       };
> >  };
> >
> > +&pipegrf {
> > +     compatible = "rockchip,rk3568-pipe-grf", "syscon";
> > +};
> > +
> >  &power {
> >       power-domain@RK3568_PD_PIPE {
> >               reg = <RK3568_PD_PIPE>;
> > @@ -114,3 +118,8 @@ power-domain@RK3568_PD_PIPE {
> >               #power-domain-cells = <0>;
> >       };
> >  };
> > +
> > +&usb_host0_xhci {
> > +     phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
> > +     phy-names = "usb2-phy", "usb3-phy";
> > +};
> > diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > index 7cdef800cb3c..b22e5a514ad7 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > +++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
> > @@ -230,6 +230,50 @@ scmi_shmem: sram@0 {
> >               };
> >       };
> >
> > +     usb_host0_xhci: usb@fcc00000 {
> > +             compatible = "rockchip,rk3568-dwc3", "snps,dwc3";
> > +             reg = <0x0 0xfcc00000 0x0 0x400000>;
> > +             interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
> > +             clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
> > +                      <&cru ACLK_USB3OTG0>;
> > +             clock-names = "ref_clk", "suspend_clk",
> > +                           "bus_clk";
> > +             dr_mode = "host";
> > +             phy_type = "utmi_wide";
>
> > +             power-domains = <&power RK3568_PD_PIPE>;
>
> When both usb_host0_xhci and usb_host1_xhci are connected to a usb2phy
> and the combphy's disabled there's no PCLK_PIPE enabled.
> Fix logic for RK3568_PD_PIPE by adding the USB3 clocks.
>
>
> > +             resets = <&cru SRST_USB3OTG0>;
>
> > +             reset-names = "usb3-otg";
>
> remove
>
> snps,dwc3.yaml only mentions the "resets" because
> devm_reset_control_array_get_optional_shared is used.
> reset-names is only a rk3399 legacy that I included due to the YAML
> conversion.
> With unevaluatedProperties now working "resets" also could be removed
> from rockchip,dwc3.yaml I think.

I've tested removing the reset entirely, and it seems the issues that
affected the rk3399 do not affect us here.

>
> https://github.com/torvalds/linux/commit/2f8e928408885dad5d8d6afefacb82100b6b62c7
> Added properties for rk3399 are:
>   power-domains
>   resets
>   reset-names
>
> > +             snps,dis_enblslpm_quirk;
> > +             snps,dis-u2-freeclk-exists-quirk;
> > +             snps,dis-del-phy-power-chg-quirk;
> > +             snps,dis-tx-ipgap-linecheck-quirk;
>
> sort
>
> > +             snps,xhci-trb-ent-quirk;
>
> ???
>
> check snps,dwc3.yaml

I've tried dropping all of these and testing all the configurations I
can think of.
The only one we seem to absolutely need is snps,dis_u2_susphy_quirk,
without which sometimes devices fail to enumerate after being removed.
The only weird behavior I found was on the Pinenote, where there is
only the OTG port and when a state change happens from host to device
mode the controller locks up the AXI bus for a few seconds until it
times out and gets reset by core.
OTG support is still a work in progress here though and is not supported yet.

TLDR: I'll be dropping all the quirks that have no apparent effect in
the v3, they can be added in if needed following broader testing.

Thanks for all the insight here!

>
> > +             status = "disabled";
> > +     };
> > +
> > +     usb_host1_xhci: usb@fd000000 {
> > +             compatible = "rockchip,rk3568-dwc3", "snps,dwc3";
> > +             reg = <0x0 0xfd000000 0x0 0x400000>;
> > +             interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> > +             clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
> > +                      <&cru ACLK_USB3OTG1>;
> > +             clock-names = "ref_clk", "suspend_clk",
> > +                           "bus_clk";
> > +             dr_mode = "host";
> > +             phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
> > +             phy-names = "usb2-phy", "usb3-phy";
> > +             phy_type = "utmi_wide";
>
> > +             power-domains = <&power RK3568_PD_PIPE>;
>
> dito
>
> > +             resets = <&cru SRST_USB3OTG1>;
>
> > +             reset-names = "usb3-otg";
>
> remove
>
> > +             snps,dis_enblslpm_quirk;
> > +             snps,dis-u2-freeclk-exists-quirk;
> > +             snps,dis_u2_susphy_quirk;
> > +             snps,dis-del-phy-power-chg-quirk;
> > +             snps,dis-tx-ipgap-linecheck-quirk;
>
> sort
>
> > +             status = "disabled";
> > +     };
> > +
> >       gic: interrupt-controller@fd400000 {
> >               compatible = "arm,gic-v3";
> >               reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
> > @@ -297,7 +341,6 @@ pmu_io_domains: io-domains {
> >       };
> >
> >       pipegrf: syscon@fdc50000 {
> > -             compatible = "rockchip,rk3568-pipe-grf", "syscon";
> >               reg = <0x0 0xfdc50000 0x0 0x1000>;
> >       };
> >

Re: [PATCH v2 03/11] dt-bindings: usb: dwc3: add description for rk3568

[Rob Herring]

On Sat, 26 Feb 2022 13:41:39 -0500, Peter Geis wrote:
> The rk3568 dwc3 controllers are backwards compatible with the rk3399.
> Add the device tree description for it.
> 
> Signed-off-by: Peter Geis <pgwipeout@gmail.com>
> ---
>  Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>