* [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range
@ 2019-03-25 13:55 Axel Lin
2019-03-25 13:58 ` Bartosz Golaszewski
` (2 more replies)
0 siblings, 3 replies; 9+ messages in thread
From: Axel Lin @ 2019-03-25 13:55 UTC (permalink / raw)
To: Mark Brown; +Cc: Bartosz Golaszewski, Liam Girdwood, linux-kernel, Axel Lin
The pickable linear range is suitable for The MAX77651 SBB1.
According to MAX77651 TV_SBB1 Code Table:
Use BIT[1:0] as range selectors.
Use BIT[5:2] as selectors for each linear range.
The MAX77651 SBB1 supports up to selector 57, selector 58 ~ 63 are RSVD,
thus set n_voltage to 58.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
---
Hi Bartosz,
I don't have this h/w, please help to review and test this patch.
Thanks,
Axel
drivers/regulator/max77650-regulator.c | 134 +++++++++----------------
1 file changed, 45 insertions(+), 89 deletions(-)
diff --git a/drivers/regulator/max77650-regulator.c b/drivers/regulator/max77650-regulator.c
index 5c4f86c98510..24b4a0a3c3bb 100644
--- a/drivers/regulator/max77650-regulator.c
+++ b/drivers/regulator/max77650-regulator.c
@@ -20,6 +20,8 @@
#define MAX77650_REGULATOR_V_LDO_MASK GENMASK(6, 0)
#define MAX77650_REGULATOR_V_SBB_MASK GENMASK(5, 0)
+#define MAX77651_REGULATOR_V_SBB1_MASK GENMASK(5, 2)
+#define MAX77651_REGULATOR_V_SBB1_RANGE_MASK GENMASK(1, 0)
#define MAX77650_REGULATOR_AD_MASK BIT(3)
#define MAX77650_REGULATOR_AD_DISABLED 0x00
@@ -27,6 +29,8 @@
#define MAX77650_REGULATOR_CURR_LIM_MASK GENMASK(7, 6)
+static struct max77650_regulator_desc max77651_SBB1_desc;
+
enum {
MAX77650_REGULATOR_ID_LDO = 0,
MAX77650_REGULATOR_ID_SBB0,
@@ -41,43 +45,20 @@ struct max77650_regulator_desc {
unsigned int regB;
};
-static const unsigned int max77651_sbb1_regulator_volt_table[] = {
- 2400000, 3200000, 4000000, 4800000,
- 2450000, 3250000, 4050000, 4850000,
- 2500000, 3300000, 4100000, 4900000,
- 2550000, 3350000, 4150000, 4950000,
- 2600000, 3400000, 4200000, 5000000,
- 2650000, 3450000, 4250000, 5050000,
- 2700000, 3500000, 4300000, 5100000,
- 2750000, 3550000, 4350000, 5150000,
- 2800000, 3600000, 4400000, 5200000,
- 2850000, 3650000, 4450000, 5250000,
- 2900000, 3700000, 4500000, 0,
- 2950000, 3750000, 4550000, 0,
- 3000000, 3800000, 4600000, 0,
- 3050000, 3850000, 4650000, 0,
- 3100000, 3900000, 4700000, 0,
- 3150000, 3950000, 4750000, 0,
+static const unsigned int max77651_sbb1_volt_range_sel[] = {
+ 0x0, 0x1, 0x2, 0x3
};
-#define MAX77651_REGULATOR_SBB1_SEL_DEC(_val) \
- (((_val & 0x3c) >> 2) | ((_val & 0x03) << 4))
-#define MAX77651_REGULATOR_SBB1_SEL_ENC(_val) \
- (((_val & 0x30) >> 4) | ((_val & 0x0f) << 2))
-
-#define MAX77650_REGULATOR_SBB1_SEL_DECR(_val) \
- do { \
- _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \
- _val--; \
- _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \
- } while (0)
-
-#define MAX77650_REGULATOR_SBB1_SEL_INCR(_val) \
- do { \
- _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \
- _val++; \
- _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \
- } while (0)
+static const struct regulator_linear_range max77651_sbb1_volt_ranges[] = {
+ /* range index 0 */
+ REGULATOR_LINEAR_RANGE(2400000, 0x00, 0x0f, 50000),
+ /* range index 1 */
+ REGULATOR_LINEAR_RANGE(3200000, 0x00, 0x0f, 50000),
+ /* range index 2 */
+ REGULATOR_LINEAR_RANGE(4000000, 0x00, 0x0f, 50000),
+ /* range index 3 */
+ REGULATOR_LINEAR_RANGE(4800000, 0x00, 0x09, 50000),
+};
static const unsigned int max77650_current_limit_table[] = {
1000000, 866000, 707000, 500000,
@@ -130,6 +111,7 @@ static int max77650_regulator_disable(struct regulator_dev *rdev)
static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
unsigned int sel)
{
+ struct max77650_regulator_desc *rdesc = rdev_get_drvdata(rdev);
int rv = 0, curr, diff;
bool ascending;
@@ -137,15 +119,24 @@ static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
* If the regulator is disabled, we can program the desired
* voltage right away.
*/
- if (!max77650_regulator_is_enabled(rdev))
- return regulator_set_voltage_sel_regmap(rdev, sel);
+ if (!max77650_regulator_is_enabled(rdev)) {
+ if (rdesc == &max77651_SBB1_desc)
+ return regulator_set_voltage_sel_pickable_regmap(rdev,
+ sel);
+ else
+ return regulator_set_voltage_sel_regmap(rdev, sel);
+ }
/*
* Otherwise we need to manually ramp the output voltage up/down
* one step at a time.
*/
- curr = regulator_get_voltage_sel_regmap(rdev);
+ if (rdesc == &max77651_SBB1_desc)
+ curr = regulator_get_voltage_sel_pickable_regmap(rdev);
+ else
+ curr = regulator_get_voltage_sel_regmap(rdev);
+
if (curr < 0)
return curr;
@@ -162,57 +153,18 @@ static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
* the selector equals 0.
*/
for (ascending ? curr++ : curr--;; ascending ? curr++ : curr--) {
- rv = regulator_set_voltage_sel_regmap(rdev, curr);
- if (rv)
- return rv;
-
- if (curr == sel)
- break;
- }
-
- return 0;
-}
-
-/*
- * Special case: non-linear voltage table for max77651 SBB1 - software
- * must ensure the voltage is ramped in 50mV increments.
- */
-static int max77651_regulator_sbb1_set_voltage_sel(struct regulator_dev *rdev,
- unsigned int sel)
-{
- int rv = 0, curr, vcurr, vdest, vdiff;
-
- /*
- * If the regulator is disabled, we can program the desired
- * voltage right away.
- */
- if (!max77650_regulator_is_enabled(rdev))
- return regulator_set_voltage_sel_regmap(rdev, sel);
-
- curr = regulator_get_voltage_sel_regmap(rdev);
- if (curr < 0)
- return curr;
-
- if (curr == sel)
- return 0; /* Already there. */
-
- vcurr = max77651_sbb1_regulator_volt_table[curr];
- vdest = max77651_sbb1_regulator_volt_table[sel];
- vdiff = vcurr - vdest;
-
- for (;;) {
- if (vdiff > 0)
- MAX77650_REGULATOR_SBB1_SEL_DECR(curr);
+ if (rdesc == &max77651_SBB1_desc)
+ rv = regulator_set_voltage_sel_pickable_regmap(rdev,
+ curr);
else
- MAX77650_REGULATOR_SBB1_SEL_INCR(curr);
+ rv = regulator_set_voltage_sel_regmap(rdev, curr);
- rv = regulator_set_voltage_sel_regmap(rdev, curr);
if (rv)
return rv;
if (curr == sel)
break;
- };
+ }
return 0;
}
@@ -241,14 +193,14 @@ static const struct regulator_ops max77650_regulator_SBB_ops = {
.set_active_discharge = regulator_set_active_discharge_regmap,
};
-/* Special case for max77651 SBB1 - non-linear voltage mapping. */
+/* Special case for max77651 SBB1 - pickable linear-range voltage mapping. */
static const struct regulator_ops max77651_SBB1_regulator_ops = {
.is_enabled = max77650_regulator_is_enabled,
.enable = max77650_regulator_enable,
.disable = max77650_regulator_disable,
- .list_voltage = regulator_list_voltage_table,
- .get_voltage_sel = regulator_get_voltage_sel_regmap,
- .set_voltage_sel = max77651_regulator_sbb1_set_voltage_sel,
+ .list_voltage = regulator_list_voltage_pickable_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
+ .set_voltage_sel = max77650_regulator_set_voltage_sel,
.get_current_limit = regulator_get_current_limit_regmap,
.set_current_limit = regulator_set_current_limit_regmap,
.set_active_discharge = regulator_set_active_discharge_regmap,
@@ -345,9 +297,13 @@ static struct max77650_regulator_desc max77651_SBB1_desc = {
.supply_name = "in-sbb1",
.id = MAX77650_REGULATOR_ID_SBB1,
.ops = &max77651_SBB1_regulator_ops,
- .volt_table = max77651_sbb1_regulator_volt_table,
- .n_voltages = ARRAY_SIZE(max77651_sbb1_regulator_volt_table),
- .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK,
+ .linear_range_selectors = max77651_sbb1_volt_range_sel,
+ .linear_ranges = max77651_sbb1_volt_ranges,
+ .n_linear_ranges = ARRAY_SIZE(max77651_sbb1_volt_ranges),
+ .n_voltages = 58,
+ .vsel_range_mask = MAX77651_REGULATOR_V_SBB1_RANGE_MASK,
+ .vsel_range_reg = MAX77650_REG_CNFG_SBB1_A,
+ .vsel_mask = MAX77651_REGULATOR_V_SBB1_MASK,
.vsel_reg = MAX77650_REG_CNFG_SBB1_A,
.active_discharge_off = MAX77650_REGULATOR_AD_DISABLED,
.active_discharge_on = MAX77650_REGULATOR_AD_ENABLED,
--
2.17.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range
2019-03-25 13:55 [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range Axel Lin
@ 2019-03-25 13:58 ` Bartosz Golaszewski
2019-03-27 10:01 ` Bartosz Golaszewski
2019-05-08 9:08 ` Applied "regulator: max77650: Convert MAX77651 SBB1 to pickable linear range" to the regulator tree Mark Brown
2 siblings, 0 replies; 9+ messages in thread
From: Bartosz Golaszewski @ 2019-03-25 13:58 UTC (permalink / raw)
To: Axel Lin; +Cc: Mark Brown, Liam Girdwood, LKML
pon., 25 mar 2019 o 14:56 Axel Lin <axel.lin@ingics.com> napisał(a):
>
> The pickable linear range is suitable for The MAX77651 SBB1.
> According to MAX77651 TV_SBB1 Code Table:
> Use BIT[1:0] as range selectors.
> Use BIT[5:2] as selectors for each linear range.
>
> The MAX77651 SBB1 supports up to selector 57, selector 58 ~ 63 are RSVD,
> thus set n_voltage to 58.
>
> Signed-off-by: Axel Lin <axel.lin@ingics.com>
> ---
> Hi Bartosz,
> I don't have this h/w, please help to review and test this patch.
> Thanks,
> Axel
>
> drivers/regulator/max77650-regulator.c | 134 +++++++++----------------
> 1 file changed, 45 insertions(+), 89 deletions(-)
>
> diff --git a/drivers/regulator/max77650-regulator.c b/drivers/regulator/max77650-regulator.c
> index 5c4f86c98510..24b4a0a3c3bb 100644
> --- a/drivers/regulator/max77650-regulator.c
> +++ b/drivers/regulator/max77650-regulator.c
> @@ -20,6 +20,8 @@
>
> #define MAX77650_REGULATOR_V_LDO_MASK GENMASK(6, 0)
> #define MAX77650_REGULATOR_V_SBB_MASK GENMASK(5, 0)
> +#define MAX77651_REGULATOR_V_SBB1_MASK GENMASK(5, 2)
> +#define MAX77651_REGULATOR_V_SBB1_RANGE_MASK GENMASK(1, 0)
>
> #define MAX77650_REGULATOR_AD_MASK BIT(3)
> #define MAX77650_REGULATOR_AD_DISABLED 0x00
> @@ -27,6 +29,8 @@
>
> #define MAX77650_REGULATOR_CURR_LIM_MASK GENMASK(7, 6)
>
> +static struct max77650_regulator_desc max77651_SBB1_desc;
> +
> enum {
> MAX77650_REGULATOR_ID_LDO = 0,
> MAX77650_REGULATOR_ID_SBB0,
> @@ -41,43 +45,20 @@ struct max77650_regulator_desc {
> unsigned int regB;
> };
>
> -static const unsigned int max77651_sbb1_regulator_volt_table[] = {
> - 2400000, 3200000, 4000000, 4800000,
> - 2450000, 3250000, 4050000, 4850000,
> - 2500000, 3300000, 4100000, 4900000,
> - 2550000, 3350000, 4150000, 4950000,
> - 2600000, 3400000, 4200000, 5000000,
> - 2650000, 3450000, 4250000, 5050000,
> - 2700000, 3500000, 4300000, 5100000,
> - 2750000, 3550000, 4350000, 5150000,
> - 2800000, 3600000, 4400000, 5200000,
> - 2850000, 3650000, 4450000, 5250000,
> - 2900000, 3700000, 4500000, 0,
> - 2950000, 3750000, 4550000, 0,
> - 3000000, 3800000, 4600000, 0,
> - 3050000, 3850000, 4650000, 0,
> - 3100000, 3900000, 4700000, 0,
> - 3150000, 3950000, 4750000, 0,
> +static const unsigned int max77651_sbb1_volt_range_sel[] = {
> + 0x0, 0x1, 0x2, 0x3
> };
>
> -#define MAX77651_REGULATOR_SBB1_SEL_DEC(_val) \
> - (((_val & 0x3c) >> 2) | ((_val & 0x03) << 4))
> -#define MAX77651_REGULATOR_SBB1_SEL_ENC(_val) \
> - (((_val & 0x30) >> 4) | ((_val & 0x0f) << 2))
> -
> -#define MAX77650_REGULATOR_SBB1_SEL_DECR(_val) \
> - do { \
> - _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \
> - _val--; \
> - _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \
> - } while (0)
> -
> -#define MAX77650_REGULATOR_SBB1_SEL_INCR(_val) \
> - do { \
> - _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \
> - _val++; \
> - _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \
> - } while (0)
> +static const struct regulator_linear_range max77651_sbb1_volt_ranges[] = {
> + /* range index 0 */
> + REGULATOR_LINEAR_RANGE(2400000, 0x00, 0x0f, 50000),
> + /* range index 1 */
> + REGULATOR_LINEAR_RANGE(3200000, 0x00, 0x0f, 50000),
> + /* range index 2 */
> + REGULATOR_LINEAR_RANGE(4000000, 0x00, 0x0f, 50000),
> + /* range index 3 */
> + REGULATOR_LINEAR_RANGE(4800000, 0x00, 0x09, 50000),
> +};
>
> static const unsigned int max77650_current_limit_table[] = {
> 1000000, 866000, 707000, 500000,
> @@ -130,6 +111,7 @@ static int max77650_regulator_disable(struct regulator_dev *rdev)
> static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
> unsigned int sel)
> {
> + struct max77650_regulator_desc *rdesc = rdev_get_drvdata(rdev);
> int rv = 0, curr, diff;
> bool ascending;
>
> @@ -137,15 +119,24 @@ static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
> * If the regulator is disabled, we can program the desired
> * voltage right away.
> */
> - if (!max77650_regulator_is_enabled(rdev))
> - return regulator_set_voltage_sel_regmap(rdev, sel);
> + if (!max77650_regulator_is_enabled(rdev)) {
> + if (rdesc == &max77651_SBB1_desc)
> + return regulator_set_voltage_sel_pickable_regmap(rdev,
> + sel);
> + else
> + return regulator_set_voltage_sel_regmap(rdev, sel);
> + }
>
> /*
> * Otherwise we need to manually ramp the output voltage up/down
> * one step at a time.
> */
>
> - curr = regulator_get_voltage_sel_regmap(rdev);
> + if (rdesc == &max77651_SBB1_desc)
> + curr = regulator_get_voltage_sel_pickable_regmap(rdev);
> + else
> + curr = regulator_get_voltage_sel_regmap(rdev);
> +
> if (curr < 0)
> return curr;
>
> @@ -162,57 +153,18 @@ static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
> * the selector equals 0.
> */
> for (ascending ? curr++ : curr--;; ascending ? curr++ : curr--) {
> - rv = regulator_set_voltage_sel_regmap(rdev, curr);
> - if (rv)
> - return rv;
> -
> - if (curr == sel)
> - break;
> - }
> -
> - return 0;
> -}
> -
> -/*
> - * Special case: non-linear voltage table for max77651 SBB1 - software
> - * must ensure the voltage is ramped in 50mV increments.
> - */
> -static int max77651_regulator_sbb1_set_voltage_sel(struct regulator_dev *rdev,
> - unsigned int sel)
> -{
> - int rv = 0, curr, vcurr, vdest, vdiff;
> -
> - /*
> - * If the regulator is disabled, we can program the desired
> - * voltage right away.
> - */
> - if (!max77650_regulator_is_enabled(rdev))
> - return regulator_set_voltage_sel_regmap(rdev, sel);
> -
> - curr = regulator_get_voltage_sel_regmap(rdev);
> - if (curr < 0)
> - return curr;
> -
> - if (curr == sel)
> - return 0; /* Already there. */
> -
> - vcurr = max77651_sbb1_regulator_volt_table[curr];
> - vdest = max77651_sbb1_regulator_volt_table[sel];
> - vdiff = vcurr - vdest;
> -
> - for (;;) {
> - if (vdiff > 0)
> - MAX77650_REGULATOR_SBB1_SEL_DECR(curr);
> + if (rdesc == &max77651_SBB1_desc)
> + rv = regulator_set_voltage_sel_pickable_regmap(rdev,
> + curr);
> else
> - MAX77650_REGULATOR_SBB1_SEL_INCR(curr);
> + rv = regulator_set_voltage_sel_regmap(rdev, curr);
>
> - rv = regulator_set_voltage_sel_regmap(rdev, curr);
> if (rv)
> return rv;
>
> if (curr == sel)
> break;
> - };
> + }
>
> return 0;
> }
> @@ -241,14 +193,14 @@ static const struct regulator_ops max77650_regulator_SBB_ops = {
> .set_active_discharge = regulator_set_active_discharge_regmap,
> };
>
> -/* Special case for max77651 SBB1 - non-linear voltage mapping. */
> +/* Special case for max77651 SBB1 - pickable linear-range voltage mapping. */
> static const struct regulator_ops max77651_SBB1_regulator_ops = {
> .is_enabled = max77650_regulator_is_enabled,
> .enable = max77650_regulator_enable,
> .disable = max77650_regulator_disable,
> - .list_voltage = regulator_list_voltage_table,
> - .get_voltage_sel = regulator_get_voltage_sel_regmap,
> - .set_voltage_sel = max77651_regulator_sbb1_set_voltage_sel,
> + .list_voltage = regulator_list_voltage_pickable_linear_range,
> + .get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
> + .set_voltage_sel = max77650_regulator_set_voltage_sel,
> .get_current_limit = regulator_get_current_limit_regmap,
> .set_current_limit = regulator_set_current_limit_regmap,
> .set_active_discharge = regulator_set_active_discharge_regmap,
> @@ -345,9 +297,13 @@ static struct max77650_regulator_desc max77651_SBB1_desc = {
> .supply_name = "in-sbb1",
> .id = MAX77650_REGULATOR_ID_SBB1,
> .ops = &max77651_SBB1_regulator_ops,
> - .volt_table = max77651_sbb1_regulator_volt_table,
> - .n_voltages = ARRAY_SIZE(max77651_sbb1_regulator_volt_table),
> - .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK,
> + .linear_range_selectors = max77651_sbb1_volt_range_sel,
> + .linear_ranges = max77651_sbb1_volt_ranges,
> + .n_linear_ranges = ARRAY_SIZE(max77651_sbb1_volt_ranges),
> + .n_voltages = 58,
> + .vsel_range_mask = MAX77651_REGULATOR_V_SBB1_RANGE_MASK,
> + .vsel_range_reg = MAX77650_REG_CNFG_SBB1_A,
> + .vsel_mask = MAX77651_REGULATOR_V_SBB1_MASK,
> .vsel_reg = MAX77650_REG_CNFG_SBB1_A,
> .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED,
> .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED,
> --
> 2.17.1
>
Oh nice! I didn't know about this feature. I'll test it tomorrow.
Bart
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range
2019-03-25 13:55 [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range Axel Lin
2019-03-25 13:58 ` Bartosz Golaszewski
@ 2019-03-27 10:01 ` Bartosz Golaszewski
2019-03-27 10:17 ` Axel Lin
2019-05-08 9:08 ` Applied "regulator: max77650: Convert MAX77651 SBB1 to pickable linear range" to the regulator tree Mark Brown
2 siblings, 1 reply; 9+ messages in thread
From: Bartosz Golaszewski @ 2019-03-27 10:01 UTC (permalink / raw)
To: Axel Lin
Cc: Mark Brown, Bartosz Golaszewski, Liam Girdwood,
Linux Kernel Mailing List
pon., 25 mar 2019 o 14:56 Axel Lin <axel.lin@ingics.com> napisał(a):
>
> The pickable linear range is suitable for The MAX77651 SBB1.
> According to MAX77651 TV_SBB1 Code Table:
> Use BIT[1:0] as range selectors.
> Use BIT[5:2] as selectors for each linear range.
>
> The MAX77651 SBB1 supports up to selector 57, selector 58 ~ 63 are RSVD,
> thus set n_voltage to 58.
>
> Signed-off-by: Axel Lin <axel.lin@ingics.com>
> ---
> Hi Bartosz,
> I don't have this h/w, please help to review and test this patch.
> Thanks,
> Axel
>
> drivers/regulator/max77650-regulator.c | 134 +++++++++----------------
> 1 file changed, 45 insertions(+), 89 deletions(-)
>
> diff --git a/drivers/regulator/max77650-regulator.c b/drivers/regulator/max77650-regulator.c
> index 5c4f86c98510..24b4a0a3c3bb 100644
> --- a/drivers/regulator/max77650-regulator.c
> +++ b/drivers/regulator/max77650-regulator.c
> @@ -20,6 +20,8 @@
>
> #define MAX77650_REGULATOR_V_LDO_MASK GENMASK(6, 0)
> #define MAX77650_REGULATOR_V_SBB_MASK GENMASK(5, 0)
> +#define MAX77651_REGULATOR_V_SBB1_MASK GENMASK(5, 2)
> +#define MAX77651_REGULATOR_V_SBB1_RANGE_MASK GENMASK(1, 0)
>
> #define MAX77650_REGULATOR_AD_MASK BIT(3)
> #define MAX77650_REGULATOR_AD_DISABLED 0x00
> @@ -27,6 +29,8 @@
>
> #define MAX77650_REGULATOR_CURR_LIM_MASK GENMASK(7, 6)
>
> +static struct max77650_regulator_desc max77651_SBB1_desc;
> +
> enum {
> MAX77650_REGULATOR_ID_LDO = 0,
> MAX77650_REGULATOR_ID_SBB0,
> @@ -41,43 +45,20 @@ struct max77650_regulator_desc {
> unsigned int regB;
> };
>
> -static const unsigned int max77651_sbb1_regulator_volt_table[] = {
> - 2400000, 3200000, 4000000, 4800000,
> - 2450000, 3250000, 4050000, 4850000,
> - 2500000, 3300000, 4100000, 4900000,
> - 2550000, 3350000, 4150000, 4950000,
> - 2600000, 3400000, 4200000, 5000000,
> - 2650000, 3450000, 4250000, 5050000,
> - 2700000, 3500000, 4300000, 5100000,
> - 2750000, 3550000, 4350000, 5150000,
> - 2800000, 3600000, 4400000, 5200000,
> - 2850000, 3650000, 4450000, 5250000,
> - 2900000, 3700000, 4500000, 0,
> - 2950000, 3750000, 4550000, 0,
> - 3000000, 3800000, 4600000, 0,
> - 3050000, 3850000, 4650000, 0,
> - 3100000, 3900000, 4700000, 0,
> - 3150000, 3950000, 4750000, 0,
> +static const unsigned int max77651_sbb1_volt_range_sel[] = {
> + 0x0, 0x1, 0x2, 0x3
> };
>
> -#define MAX77651_REGULATOR_SBB1_SEL_DEC(_val) \
> - (((_val & 0x3c) >> 2) | ((_val & 0x03) << 4))
> -#define MAX77651_REGULATOR_SBB1_SEL_ENC(_val) \
> - (((_val & 0x30) >> 4) | ((_val & 0x0f) << 2))
> -
> -#define MAX77650_REGULATOR_SBB1_SEL_DECR(_val) \
> - do { \
> - _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \
> - _val--; \
> - _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \
> - } while (0)
> -
> -#define MAX77650_REGULATOR_SBB1_SEL_INCR(_val) \
> - do { \
> - _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \
> - _val++; \
> - _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \
> - } while (0)
> +static const struct regulator_linear_range max77651_sbb1_volt_ranges[] = {
> + /* range index 0 */
> + REGULATOR_LINEAR_RANGE(2400000, 0x00, 0x0f, 50000),
> + /* range index 1 */
> + REGULATOR_LINEAR_RANGE(3200000, 0x00, 0x0f, 50000),
> + /* range index 2 */
> + REGULATOR_LINEAR_RANGE(4000000, 0x00, 0x0f, 50000),
> + /* range index 3 */
> + REGULATOR_LINEAR_RANGE(4800000, 0x00, 0x09, 50000),
> +};
>
> static const unsigned int max77650_current_limit_table[] = {
> 1000000, 866000, 707000, 500000,
> @@ -130,6 +111,7 @@ static int max77650_regulator_disable(struct regulator_dev *rdev)
> static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
> unsigned int sel)
> {
> + struct max77650_regulator_desc *rdesc = rdev_get_drvdata(rdev);
> int rv = 0, curr, diff;
> bool ascending;
>
> @@ -137,15 +119,24 @@ static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
> * If the regulator is disabled, we can program the desired
> * voltage right away.
> */
> - if (!max77650_regulator_is_enabled(rdev))
> - return regulator_set_voltage_sel_regmap(rdev, sel);
> + if (!max77650_regulator_is_enabled(rdev)) {
> + if (rdesc == &max77651_SBB1_desc)
> + return regulator_set_voltage_sel_pickable_regmap(rdev,
> + sel);
> + else
> + return regulator_set_voltage_sel_regmap(rdev, sel);
> + }
>
> /*
> * Otherwise we need to manually ramp the output voltage up/down
> * one step at a time.
> */
>
> - curr = regulator_get_voltage_sel_regmap(rdev);
> + if (rdesc == &max77651_SBB1_desc)
> + curr = regulator_get_voltage_sel_pickable_regmap(rdev);
> + else
> + curr = regulator_get_voltage_sel_regmap(rdev);
> +
> if (curr < 0)
> return curr;
>
> @@ -162,57 +153,18 @@ static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
> * the selector equals 0.
> */
> for (ascending ? curr++ : curr--;; ascending ? curr++ : curr--) {
> - rv = regulator_set_voltage_sel_regmap(rdev, curr);
> - if (rv)
> - return rv;
> -
> - if (curr == sel)
> - break;
> - }
> -
> - return 0;
> -}
> -
> -/*
> - * Special case: non-linear voltage table for max77651 SBB1 - software
> - * must ensure the voltage is ramped in 50mV increments.
> - */
> -static int max77651_regulator_sbb1_set_voltage_sel(struct regulator_dev *rdev,
> - unsigned int sel)
> -{
> - int rv = 0, curr, vcurr, vdest, vdiff;
> -
> - /*
> - * If the regulator is disabled, we can program the desired
> - * voltage right away.
> - */
> - if (!max77650_regulator_is_enabled(rdev))
> - return regulator_set_voltage_sel_regmap(rdev, sel);
> -
> - curr = regulator_get_voltage_sel_regmap(rdev);
> - if (curr < 0)
> - return curr;
> -
> - if (curr == sel)
> - return 0; /* Already there. */
> -
> - vcurr = max77651_sbb1_regulator_volt_table[curr];
> - vdest = max77651_sbb1_regulator_volt_table[sel];
> - vdiff = vcurr - vdest;
> -
> - for (;;) {
> - if (vdiff > 0)
> - MAX77650_REGULATOR_SBB1_SEL_DECR(curr);
> + if (rdesc == &max77651_SBB1_desc)
> + rv = regulator_set_voltage_sel_pickable_regmap(rdev,
> + curr);
> else
> - MAX77650_REGULATOR_SBB1_SEL_INCR(curr);
> + rv = regulator_set_voltage_sel_regmap(rdev, curr);
>
> - rv = regulator_set_voltage_sel_regmap(rdev, curr);
> if (rv)
> return rv;
>
> if (curr == sel)
> break;
> - };
> + }
>
> return 0;
> }
> @@ -241,14 +193,14 @@ static const struct regulator_ops max77650_regulator_SBB_ops = {
> .set_active_discharge = regulator_set_active_discharge_regmap,
> };
>
> -/* Special case for max77651 SBB1 - non-linear voltage mapping. */
> +/* Special case for max77651 SBB1 - pickable linear-range voltage mapping. */
> static const struct regulator_ops max77651_SBB1_regulator_ops = {
> .is_enabled = max77650_regulator_is_enabled,
> .enable = max77650_regulator_enable,
> .disable = max77650_regulator_disable,
> - .list_voltage = regulator_list_voltage_table,
> - .get_voltage_sel = regulator_get_voltage_sel_regmap,
> - .set_voltage_sel = max77651_regulator_sbb1_set_voltage_sel,
> + .list_voltage = regulator_list_voltage_pickable_linear_range,
> + .get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
> + .set_voltage_sel = max77650_regulator_set_voltage_sel,
> .get_current_limit = regulator_get_current_limit_regmap,
> .set_current_limit = regulator_set_current_limit_regmap,
> .set_active_discharge = regulator_set_active_discharge_regmap,
> @@ -345,9 +297,13 @@ static struct max77650_regulator_desc max77651_SBB1_desc = {
> .supply_name = "in-sbb1",
> .id = MAX77650_REGULATOR_ID_SBB1,
> .ops = &max77651_SBB1_regulator_ops,
> - .volt_table = max77651_sbb1_regulator_volt_table,
> - .n_voltages = ARRAY_SIZE(max77651_sbb1_regulator_volt_table),
> - .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK,
> + .linear_range_selectors = max77651_sbb1_volt_range_sel,
> + .linear_ranges = max77651_sbb1_volt_ranges,
> + .n_linear_ranges = ARRAY_SIZE(max77651_sbb1_volt_ranges),
> + .n_voltages = 58,
> + .vsel_range_mask = MAX77651_REGULATOR_V_SBB1_RANGE_MASK,
> + .vsel_range_reg = MAX77650_REG_CNFG_SBB1_A,
> + .vsel_mask = MAX77651_REGULATOR_V_SBB1_MASK,
> .vsel_reg = MAX77650_REG_CNFG_SBB1_A,
> .active_discharge_off = MAX77650_REGULATOR_AD_DISABLED,
> .active_discharge_on = MAX77650_REGULATOR_AD_ENABLED,
> --
> 2.17.1
>
Hi,
what tree is this patch based on, because it doesn't apply on top of v5.1-rc2.
Bart
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range
2019-03-27 10:01 ` Bartosz Golaszewski
@ 2019-03-27 10:17 ` Axel Lin
2019-03-27 13:07 ` Bartosz Golaszewski
0 siblings, 1 reply; 9+ messages in thread
From: Axel Lin @ 2019-03-27 10:17 UTC (permalink / raw)
To: Bartosz Golaszewski
Cc: Mark Brown, Bartosz Golaszewski, Liam Girdwood,
Linux Kernel Mailing List
> Hi,
>
> what tree is this patch based on, because it doesn't apply on top of v5.1-rc2.
Hi Bart,
You can use linux-next or regulator tree.
However, due to build dependency you need to manually apply max77650
mfd drvier manually because it's not exist in these tree.
Alternatively, you can check the difference of your tree with
linux-next regarding max77650-regulator.c changes.
Then pickup related patches first so you can cleanly apply this patch.
Regards,
Axel
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range
2019-03-27 10:17 ` Axel Lin
@ 2019-03-27 13:07 ` Bartosz Golaszewski
2019-03-27 13:56 ` Axel Lin
0 siblings, 1 reply; 9+ messages in thread
From: Bartosz Golaszewski @ 2019-03-27 13:07 UTC (permalink / raw)
To: Axel Lin
Cc: Mark Brown, Bartosz Golaszewski, Liam Girdwood,
Linux Kernel Mailing List
śr., 27 mar 2019 o 11:17 Axel Lin <axel.lin@ingics.com> napisał(a):
>
> > Hi,
> >
> > what tree is this patch based on, because it doesn't apply on top of v5.1-rc2.
> Hi Bart,
> You can use linux-next or regulator tree.
> However, due to build dependency you need to manually apply max77650
> mfd drvier manually because it's not exist in these tree.
>
> Alternatively, you can check the difference of your tree with
> linux-next regarding max77650-regulator.c changes.
> Then pickup related patches first so you can cleanly apply this patch.
>
> Regards,
> Axel
Can you push a branch you used somewhere public? It'll be faster that way.
Bart
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range
2019-03-27 13:07 ` Bartosz Golaszewski
@ 2019-03-27 13:56 ` Axel Lin
2019-03-27 14:00 ` Bartosz Golaszewski
0 siblings, 1 reply; 9+ messages in thread
From: Axel Lin @ 2019-03-27 13:56 UTC (permalink / raw)
To: Bartosz Golaszewski
Cc: Mark Brown, Bartosz Golaszewski, Liam Girdwood,
Linux Kernel Mailing List
Bartosz Golaszewski <brgl@bgdev.pl> 於 2019年3月27日 週三 下午9:08寫道：
>
> śr., 27 mar 2019 o 11:17 Axel Lin <axel.lin@ingics.com> napisał(a):
> >
> > > Hi,
> > >
> > > what tree is this patch based on, because it doesn't apply on top of v5.1-rc2.
> > Hi Bart,
> > You can use linux-next or regulator tree.
> > However, due to build dependency you need to manually apply max77650
> > mfd drvier manually because it's not exist in these tree.
> >
> > Alternatively, you can check the difference of your tree with
> > linux-next regarding max77650-regulator.c changes.
> > Then pickup related patches first so you can cleanly apply this patch.
> >
> > Regards,
> > Axel
>
> Can you push a branch you used somewhere public? It'll be faster that way.
I don't have public git tree for linux-kernel.
I think you should try linux-next tree, this patch can be applied to linux-next.
Other missing files should be all your patches:
https://patchwork.kernel.org/cover/10809945/
Regards,
Axel
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range
2019-03-27 13:56 ` Axel Lin
@ 2019-03-27 14:00 ` Bartosz Golaszewski
2019-03-28 11:51 ` Axel Lin
0 siblings, 1 reply; 9+ messages in thread
From: Bartosz Golaszewski @ 2019-03-27 14:00 UTC (permalink / raw)
To: Axel Lin
Cc: Mark Brown, Bartosz Golaszewski, Liam Girdwood,
Linux Kernel Mailing List
śr., 27 mar 2019 o 14:56 Axel Lin <axel.lin@ingics.com> napisał(a):
>
> Bartosz Golaszewski <brgl@bgdev.pl> 於 2019年3月27日 週三 下午9:08寫道：
> >
> > śr., 27 mar 2019 o 11:17 Axel Lin <axel.lin@ingics.com> napisał(a):
> > >
> > > > Hi,
> > > >
> > > > what tree is this patch based on, because it doesn't apply on top of v5.1-rc2.
> > > Hi Bart,
> > > You can use linux-next or regulator tree.
> > > However, due to build dependency you need to manually apply max77650
> > > mfd drvier manually because it's not exist in these tree.
> > >
> > > Alternatively, you can check the difference of your tree with
> > > linux-next regarding max77650-regulator.c changes.
> > > Then pickup related patches first so you can cleanly apply this patch.
> > >
> > > Regards,
> > > Axel
> >
> > Can you push a branch you used somewhere public? It'll be faster that way.
> I don't have public git tree for linux-kernel.
> I think you should try linux-next tree, this patch can be applied to linux-next.
> Other missing files should be all your patches:
> https://patchwork.kernel.org/cover/10809945/
>
> Regards,
> Axel
What do you mean you don't have a public git tree? Can't you create a
gitlab account and just push the tree there? Alternatively, given the
amount of patches you send, I doubt the kernel.org maintainers would
refuse if you asked for an account.
Frankly, this week is quite busy for me, so if you want me to play
with pulling random patches, then the test will have to wait until
next week.
Best regards,
Bartosz Golaszewski
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range
2019-03-27 14:00 ` Bartosz Golaszewski
@ 2019-03-28 11:51 ` Axel Lin
0 siblings, 0 replies; 9+ messages in thread
From: Axel Lin @ 2019-03-28 11:51 UTC (permalink / raw)
To: Bartosz Golaszewski
Cc: Mark Brown, Bartosz Golaszewski, Liam Girdwood,
Linux Kernel Mailing List
> What do you mean you don't have a public git tree? Can't you create a
> gitlab account and just push the tree there? Alternatively, given the
> amount of patches you send, I doubt the kernel.org maintainers would
> refuse if you asked for an account.
Because using linux-next tree is good enough for me.
>
> Frankly, this week is quite busy for me, so if you want me to play
> with pulling random patches, then the test will have to wait until
> next week.
No hurry.
You can test it when you have time to do that.
Regards,
Axel
^ permalink raw reply [flat|nested] 9+ messages in thread
* Applied "regulator: max77650: Convert MAX77651 SBB1 to pickable linear range" to the regulator tree
2019-03-25 13:55 [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range Axel Lin
2019-03-25 13:58 ` Bartosz Golaszewski
2019-03-27 10:01 ` Bartosz Golaszewski
@ 2019-05-08 9:08 ` Mark Brown
2 siblings, 0 replies; 9+ messages in thread
From: Mark Brown @ 2019-05-08 9:08 UTC (permalink / raw)
To: Axel Lin; +Cc: Bartosz Golaszewski, Liam Girdwood, linux-kernel, Mark Brown
The patch
regulator: max77650: Convert MAX77651 SBB1 to pickable linear range
has been applied to the regulator tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-5.3
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
From 3df4235ac41c2b8c3c5cd9c7798bc4a3105c0bc4 Mon Sep 17 00:00:00 2001
From: Axel Lin <axel.lin@ingics.com>
Date: Mon, 25 Mar 2019 21:55:57 +0800
Subject: [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear
range
The pickable linear range is suitable for The MAX77651 SBB1.
According to MAX77651 TV_SBB1 Code Table:
Use BIT[1:0] as range selectors.
Use BIT[5:2] as selectors for each linear range.
The MAX77651 SBB1 supports up to selector 57, selector 58 ~ 63 are RSVD,
thus set n_voltage to 58.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
drivers/regulator/max77650-regulator.c | 134 +++++++++----------------
1 file changed, 45 insertions(+), 89 deletions(-)
diff --git a/drivers/regulator/max77650-regulator.c b/drivers/regulator/max77650-regulator.c
index 5c4f86c98510..ecf8cf7aad20 100644
--- a/drivers/regulator/max77650-regulator.c
+++ b/drivers/regulator/max77650-regulator.c
@@ -20,6 +20,8 @@
#define MAX77650_REGULATOR_V_LDO_MASK GENMASK(6, 0)
#define MAX77650_REGULATOR_V_SBB_MASK GENMASK(5, 0)
+#define MAX77651_REGULATOR_V_SBB1_MASK GENMASK(5, 2)
+#define MAX77651_REGULATOR_V_SBB1_RANGE_MASK GENMASK(1, 0)
#define MAX77650_REGULATOR_AD_MASK BIT(3)
#define MAX77650_REGULATOR_AD_DISABLED 0x00
@@ -27,6 +29,8 @@
#define MAX77650_REGULATOR_CURR_LIM_MASK GENMASK(7, 6)
+static struct max77650_regulator_desc max77651_SBB1_desc;
+
enum {
MAX77650_REGULATOR_ID_LDO = 0,
MAX77650_REGULATOR_ID_SBB0,
@@ -41,43 +45,20 @@ struct max77650_regulator_desc {
unsigned int regB;
};
-static const unsigned int max77651_sbb1_regulator_volt_table[] = {
- 2400000, 3200000, 4000000, 4800000,
- 2450000, 3250000, 4050000, 4850000,
- 2500000, 3300000, 4100000, 4900000,
- 2550000, 3350000, 4150000, 4950000,
- 2600000, 3400000, 4200000, 5000000,
- 2650000, 3450000, 4250000, 5050000,
- 2700000, 3500000, 4300000, 5100000,
- 2750000, 3550000, 4350000, 5150000,
- 2800000, 3600000, 4400000, 5200000,
- 2850000, 3650000, 4450000, 5250000,
- 2900000, 3700000, 4500000, 0,
- 2950000, 3750000, 4550000, 0,
- 3000000, 3800000, 4600000, 0,
- 3050000, 3850000, 4650000, 0,
- 3100000, 3900000, 4700000, 0,
- 3150000, 3950000, 4750000, 0,
+static const unsigned int max77651_sbb1_volt_range_sel[] = {
+ 0x0, 0x1, 0x2, 0x3
};
-#define MAX77651_REGULATOR_SBB1_SEL_DEC(_val) \
- (((_val & 0x3c) >> 2) | ((_val & 0x03) << 4))
-#define MAX77651_REGULATOR_SBB1_SEL_ENC(_val) \
- (((_val & 0x30) >> 4) | ((_val & 0x0f) << 2))
-
-#define MAX77650_REGULATOR_SBB1_SEL_DECR(_val) \
- do { \
- _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \
- _val--; \
- _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \
- } while (0)
-
-#define MAX77650_REGULATOR_SBB1_SEL_INCR(_val) \
- do { \
- _val = MAX77651_REGULATOR_SBB1_SEL_DEC(_val); \
- _val++; \
- _val = MAX77651_REGULATOR_SBB1_SEL_ENC(_val); \
- } while (0)
+static const struct regulator_linear_range max77651_sbb1_volt_ranges[] = {
+ /* range index 0 */
+ REGULATOR_LINEAR_RANGE(2400000, 0x00, 0x0f, 50000),
+ /* range index 1 */
+ REGULATOR_LINEAR_RANGE(3200000, 0x00, 0x0f, 50000),
+ /* range index 2 */
+ REGULATOR_LINEAR_RANGE(4000000, 0x00, 0x0f, 50000),
+ /* range index 3 */
+ REGULATOR_LINEAR_RANGE(4800000, 0x00, 0x09, 50000),
+};
static const unsigned int max77650_current_limit_table[] = {
1000000, 866000, 707000, 500000,
@@ -130,6 +111,7 @@ static int max77650_regulator_disable(struct regulator_dev *rdev)
static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
unsigned int sel)
{
+ struct max77650_regulator_desc *rdesc = rdev_get_drvdata(rdev);
int rv = 0, curr, diff;
bool ascending;
@@ -137,15 +119,24 @@ static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
* If the regulator is disabled, we can program the desired
* voltage right away.
*/
- if (!max77650_regulator_is_enabled(rdev))
- return regulator_set_voltage_sel_regmap(rdev, sel);
+ if (!max77650_regulator_is_enabled(rdev)) {
+ if (rdesc == &max77651_SBB1_desc)
+ return regulator_set_voltage_sel_pickable_regmap(rdev,
+ sel);
+ else
+ return regulator_set_voltage_sel_regmap(rdev, sel);
+ }
/*
* Otherwise we need to manually ramp the output voltage up/down
* one step at a time.
*/
- curr = regulator_get_voltage_sel_regmap(rdev);
+ if (rdesc == &max77651_SBB1_desc)
+ curr = regulator_get_voltage_sel_pickable_regmap(rdev);
+ else
+ curr = regulator_get_voltage_sel_regmap(rdev);
+
if (curr < 0)
return curr;
@@ -162,57 +153,18 @@ static int max77650_regulator_set_voltage_sel(struct regulator_dev *rdev,
* the selector equals 0.
*/
for (ascending ? curr++ : curr--;; ascending ? curr++ : curr--) {
- rv = regulator_set_voltage_sel_regmap(rdev, curr);
- if (rv)
- return rv;
-
- if (curr == sel)
- break;
- }
-
- return 0;
-}
-
-/*
- * Special case: non-linear voltage table for max77651 SBB1 - software
- * must ensure the voltage is ramped in 50mV increments.
- */
-static int max77651_regulator_sbb1_set_voltage_sel(struct regulator_dev *rdev,
- unsigned int sel)
-{
- int rv = 0, curr, vcurr, vdest, vdiff;
-
- /*
- * If the regulator is disabled, we can program the desired
- * voltage right away.
- */
- if (!max77650_regulator_is_enabled(rdev))
- return regulator_set_voltage_sel_regmap(rdev, sel);
-
- curr = regulator_get_voltage_sel_regmap(rdev);
- if (curr < 0)
- return curr;
-
- if (curr == sel)
- return 0; /* Already there. */
-
- vcurr = max77651_sbb1_regulator_volt_table[curr];
- vdest = max77651_sbb1_regulator_volt_table[sel];
- vdiff = vcurr - vdest;
-
- for (;;) {
- if (vdiff > 0)
- MAX77650_REGULATOR_SBB1_SEL_DECR(curr);
+ if (rdesc == &max77651_SBB1_desc)
+ rv = regulator_set_voltage_sel_pickable_regmap(rdev,
+ curr);
else
- MAX77650_REGULATOR_SBB1_SEL_INCR(curr);
+ rv = regulator_set_voltage_sel_regmap(rdev, curr);
- rv = regulator_set_voltage_sel_regmap(rdev, curr);
if (rv)
return rv;
if (curr == sel)
break;
- };
+ }
return 0;
}
@@ -241,14 +193,14 @@ static const struct regulator_ops max77650_regulator_SBB_ops = {
.set_active_discharge = regulator_set_active_discharge_regmap,
};
-/* Special case for max77651 SBB1 - non-linear voltage mapping. */
+/* Special case for max77651 SBB1 - pickable linear-range voltage mapping. */
static const struct regulator_ops max77651_SBB1_regulator_ops = {
.is_enabled = max77650_regulator_is_enabled,
.enable = max77650_regulator_enable,
.disable = max77650_regulator_disable,
- .list_voltage = regulator_list_voltage_table,
- .get_voltage_sel = regulator_get_voltage_sel_regmap,
- .set_voltage_sel = max77651_regulator_sbb1_set_voltage_sel,
+ .list_voltage = regulator_list_voltage_pickable_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
+ .set_voltage_sel = max77650_regulator_set_voltage_sel,
.get_current_limit = regulator_get_current_limit_regmap,
.set_current_limit = regulator_set_current_limit_regmap,
.set_active_discharge = regulator_set_active_discharge_regmap,
@@ -345,9 +297,13 @@ static struct max77650_regulator_desc max77651_SBB1_desc = {
.supply_name = "in-sbb1",
.id = MAX77650_REGULATOR_ID_SBB1,
.ops = &max77651_SBB1_regulator_ops,
- .volt_table = max77651_sbb1_regulator_volt_table,
- .n_voltages = ARRAY_SIZE(max77651_sbb1_regulator_volt_table),
- .vsel_mask = MAX77650_REGULATOR_V_SBB_MASK,
+ .linear_range_selectors = max77651_sbb1_volt_range_sel,
+ .linear_ranges = max77651_sbb1_volt_ranges,
+ .n_linear_ranges = ARRAY_SIZE(max77651_sbb1_volt_ranges),
+ .n_voltages = 58,
+ .vsel_range_mask = MAX77651_REGULATOR_V_SBB1_RANGE_MASK,
+ .vsel_range_reg = MAX77650_REG_CNFG_SBB1_A,
+ .vsel_mask = MAX77651_REGULATOR_V_SBB1_MASK,
.vsel_reg = MAX77650_REG_CNFG_SBB1_A,
.active_discharge_off = MAX77650_REGULATOR_AD_DISABLED,
.active_discharge_on = MAX77650_REGULATOR_AD_ENABLED,
--
2.20.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
end of thread, other threads:[~2019-05-08 9:09 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-03-25 13:55 [PATCH] regulator: max77650: Convert MAX77651 SBB1 to pickable linear range Axel Lin
2019-03-25 13:58 ` Bartosz Golaszewski
2019-03-27 10:01 ` Bartosz Golaszewski
2019-03-27 10:17 ` Axel Lin
2019-03-27 13:07 ` Bartosz Golaszewski
2019-03-27 13:56 ` Axel Lin
2019-03-27 14:00 ` Bartosz Golaszewski
2019-03-28 11:51 ` Axel Lin
2019-05-08 9:08 ` Applied "regulator: max77650: Convert MAX77651 SBB1 to pickable linear range" to the regulator tree Mark Brown
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).