[RFC PATCH 00/15] PM / devferq: Add generic exynos bus frequency driver and new passive governor

[RFC PATCH 00/15] PM / devferq: Add generic exynos bus frequency driver and new passive governor

[Chanwoo Choi]

This patch-set includes the two features as following. The generic exynos bus
frequency driver is able to support almost Exynos SoCs for bus frequency
scaling. And the new passive governor is able to make the dependency on
between devices for frequency/voltage scaling. I had posted the patch-set[1]
with the similiar concept. This is is revised version for exynos bus frequency.
- Generic exynos bus frequency driver
- New passive governor of DEVFREQ framework

Detailed descirption for patch-set:
1. Add generic exynos bus frequency driver
: This patch-set adds the generic exynos bus frequency driver for AXI bus
of sub-blocks in exynos SoC. The Samsung Exynos SoC have the common
architecture for bus between DRAM and sub-blocks in SoC.

 There are the different buses according to Exynos SoC because Exynos SoC
has the differnt sub-blocks and bus speed. In spite of this difference
among Exynos SoCs, this driver is able to support almost Exynos SoC by adding
unique data of each bus in the devicetree file.

 In devicetree, each bus node has a bus clock, regulator, operation-point
and devfreq-event devices which measure the utilization of each bus block.

For example,
- The bus of DMC block in exynos3250.dtsi are listed below:

	bus_dmc: bus_dmc {
		compatible = "samsung,exynos-bus";
		clocks = <&cmu_dmc CLK_DIV_DMC>;
		clock-names = "bus";
		operating-points-v2 = <&bus_dmc_opp_table>;
		status = "disabled";
	};

	bus_dmc_opp_table: opp_table0 {
		compatible = "operating-points-v2";
		opp-shared;

		opp00 {
			opp-hz = /bits/ 64 <50000000>;
			opp-microvolt = <800000>;
		};
		opp01 {
			opp-hz = /bits/ 64 <100000000>;
			opp-microvolt = <800000>;
		};
		opp02 {
			opp-hz = /bits/ 64 <133000000>;
			opp-microvolt = <800000>;
		};
		opp03 {
			opp-hz = /bits/ 64 <200000000>;
			opp-microvolt = <800000>;
		};
		opp04 {
			opp-hz = /bits/ 64 <400000000>;
			opp-microvolt = <875000>;
		};
	};

- Usage case to handle the frequency and voltage of bus on runtime
  in exynos3250-rinato.dts are listed below:

	&bus_dmc {
		devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
		vdd-supply = <&buck1_reg>;	/* VDD_MIF */
		status = "okay";
	};

2. Add new passive governor of DEVFREQ framework (patch5-patch7)
: This patch-set add the new passive governor for DEVFREQ framework.
The existing governors (ondemand, performance and so on) are used for DVFS
(Dynamic Voltage and Frequency Scaling) drivers. The existing governors
are independently used for specific device driver which don't give the
influence to other device drviers and also don't receive the effect from
other device drivers.

 The passive governor depends on operation of parent driver with existing
governors(ondemand, performance and so on) extremely and is not able to
decide the new frequency by oneself. According to the decided new frequency
of parent driver with governor, the passive governor uses it to decide
the appropriate frequency for own device driver. The passive governor
must need the following information from device tree:

For exameple,
 There are one more bus device drivers in Exynos3250 which need to
change their source clock according to their utilization on runtime.
But, they share the same power line (e.g., regulator). So, LEFTBUS bus
driver is operated as parent with ondemand governor and then the rest
device driver with passive governor.

 The buses of Internal block in exynos3250.dtsi are listed below:
When LEFTBUS bus driver (parent) changes the bus frequency with
ondemand governor on runtime, the rest bus devices which sharing
the same power line (VDD_INT) will change the each bus frequency
according to the decision of LEFTBUS bus driver (parent).

- INT (Internal) block
	: VDD_INT |--- LEFTBUS  |--- PERIL
		  |    (parent) |--- MFC
		  |             |--- G3D
		  |
		  |--- RIGHTBUS |--- FSYS
				|--- LCD0
				|--- PERIR
				|--- ISP
				|--- CAM

- The buss of INT block in exynos3250.dtsi are listed below:
	bus_leftbus: bus_leftbus {
		compatible = "samsung,exynos-bus";
		clocks = <&cmu CLK_DIV_GDL>;
		clock-names = "bus";
		operating-points-v2 = <&bus_leftbus_opp_table>;
		status = "disabled";
	};

	bus_rightbus: bus_rightbus {
		compatible = "samsung,exynos-bus";
		clocks = <&cmu CLK_DIV_GDR>;
		clock-names = "bus";
		operating-points-v2 = <&bus_leftbus_opp_table>;
		status = "disabled";
	};

	(Omit the rest bus dt node)

- Usage case to handle the frequency and voltage of bus on runtime
  in exynos3250-rinato.dts are listed below:
	/* Parent bus device of VDD_INT */
	&bus_leftbus {
		devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
		vdd-supply = <&buck3_reg>;
		status = "okay";
	};

	/* Passive bus device depend on LEFTBUS bus. */
	&bus_rightbus {
		devfreq = <&bus_leftbus>; /* 'devfreq' property indicates
					     the phandle of parent device. */
		status = "okay";
	};

	(Omit the rest bus dt node)

Depends on:
- This patch-set is based on devfreq.git[2].

[1] https://lkml.org/lkml/2015/1/7/872
   : [PATCHv3 0/8] devfreq: Add generic exynos memory-bus frequency driver
[2] https://git.kernel.org/cgit/linux/kernel/git/mzx/devfreq.git/ (branch: for-rafael)

Chanwoo Choi (15):
  PM / devfreq: exynos: Add generic exynos bus frequency driver
  PM / devfreq: exynos: Add documentation for generic exynos bus frequency driver
  ARM: dts: Add DMC bus node for Exynos3250
  ARM: dts: Add DMC bus freqeuncy for exynos3250-rinato/monk
  PM / devfreq: Add new passive governor
  PM / devfreq: Add devfreq_get_devfreq_by_phandle()
  PM / devfreq: Show the related information according to governor type
  PM / devfreq: exynos: Add support of bus frequency of sub-blocks using passive governor
  PM / devfreq: exynos: Update documentation for bus devices using passive governor
  PM / devfreq: exynos: Remove unused exynos4/5 busfreq driver
  ARM: dts: Add bus nodes using VDD_INT for Exynos3250
  ARM: dts: Add support of bus frequency using VDD_INT for exynos3250-rinato
  ARM: dts: Add bus nodes using VDD_MIF for Exynos4x12
  ARM: dts: Add bus nodes using VDD_INT for Exynos4x12
  ARM: dts: Add support of bus frequency for exynos4412-trats

 .../devicetree/bindings/devfreq/exynos-bus.txt     |  312 ++++++
 arch/arm/boot/dts/exynos3250-monk.dts              |    6 +
 arch/arm/boot/dts/exynos3250-rinato.dts            |   42 +
 arch/arm/boot/dts/exynos3250.dtsi                  |  186 ++++
 arch/arm/boot/dts/exynos4412-trats2.dts            |   47 +
 arch/arm/boot/dts/exynos4x12.dtsi                  |  192 ++++
 drivers/devfreq/Kconfig                            |   37 +-
 drivers/devfreq/Makefile                           |    2 +
 drivers/devfreq/devfreq.c                          |  120 ++-
 drivers/devfreq/exynos/Makefile                    |    3 +-
 drivers/devfreq/exynos/exynos-bus.c                |  543 ++++++++++
 drivers/devfreq/exynos/exynos4_bus.c               | 1055 --------------------
 drivers/devfreq/exynos/exynos4_bus.h               |  110 --
 drivers/devfreq/exynos/exynos5_bus.c               |  431 --------
 drivers/devfreq/exynos/exynos_ppmu.c               |  119 ---
 drivers/devfreq/exynos/exynos_ppmu.h               |   86 --
 drivers/devfreq/governor.h                         |    7 +
 drivers/devfreq/governor_passive.c                 |  109 ++
 drivers/devfreq/governor_performance.c             |    1 +
 drivers/devfreq/governor_powersave.c               |    1 +
 drivers/devfreq/governor_simpleondemand.c          |    1 +
 drivers/devfreq/governor_userspace.c               |    1 +
 include/linux/devfreq.h                            |   28 +
 23 files changed, 1614 insertions(+), 1825 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/devfreq/exynos-bus.txt
 create mode 100644 drivers/devfreq/exynos/exynos-bus.c
 delete mode 100644 drivers/devfreq/exynos/exynos4_bus.c
 delete mode 100644 drivers/devfreq/exynos/exynos4_bus.h
 delete mode 100644 drivers/devfreq/exynos/exynos5_bus.c
 delete mode 100644 drivers/devfreq/exynos/exynos_ppmu.c
 delete mode 100644 drivers/devfreq/exynos/exynos_ppmu.h
 create mode 100644 drivers/devfreq/governor_passive.c

-- 
1.9.1

[RFC PATCH 01/15] PM / devfreq: exynos: Add generic exynos bus frequency driver

[Chanwoo Choi]

This patch adds the generic exynos bus frequency driver for AMBA AXI bus
of sub-blocks in exynos SoC with DEVFREQ framework. The Samsung Exynos SoC
have the common architecture for bus between DRAM and sub-blocks in SoC.
This driver can support the generic bus frequency driver for Exynos SoCs.

In devicetree, Each bus block has a bus clock, regulator, operation-point
and devfreq-event devices which measure the utilization of each bus block.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 drivers/devfreq/Kconfig             |  15 ++
 drivers/devfreq/Makefile            |   1 +
 drivers/devfreq/exynos/Makefile     |   1 +
 drivers/devfreq/exynos/exynos-bus.c | 443 ++++++++++++++++++++++++++++++++++++
 4 files changed, 460 insertions(+)
 create mode 100644 drivers/devfreq/exynos/exynos-bus.c

diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
index 64281bb2f650..55ec774f794c 100644
--- a/drivers/devfreq/Kconfig
+++ b/drivers/devfreq/Kconfig
@@ -66,6 +66,21 @@ config DEVFREQ_GOV_USERSPACE
 
 comment "DEVFREQ Drivers"
 
+config ARM_EXYNOS_BUS_DEVFREQ
+	bool "ARM EXYNOS Generic Memory Bus DEVFREQ Driver"
+	depends on ARCH_EXYNOS
+	select DEVFREQ_GOV_SIMPLE_ONDEMAND
+	select DEVFREQ_EVENT_EXYNOS_PPMU
+	select PM_DEVFREQ_EVENT
+	select PM_OPP
+	help
+	  This adds the common DEVFREQ driver for Exynos Memory bus. Exynos
+	  Memory bus has one more group of memory bus (e.g, MIF and INT block).
+	  Each memory bus group could contain many memoby bus block. It reads
+	  PPMU counters of memory controllers by using DEVFREQ-event device
+	  and adjusts the operating frequencies and voltages with OPP support.
+	  This does not yet operate with optimal voltages.
+
 config ARM_EXYNOS4_BUS_DEVFREQ
 	bool "ARM Exynos4210/4212/4412 Memory Bus DEVFREQ Driver"
 	depends on (CPU_EXYNOS4210 || SOC_EXYNOS4212 || SOC_EXYNOS4412) && !ARCH_MULTIPLATFORM
diff --git a/drivers/devfreq/Makefile b/drivers/devfreq/Makefile
index 5134f9ee983d..375ebbb4fcfb 100644
--- a/drivers/devfreq/Makefile
+++ b/drivers/devfreq/Makefile
@@ -6,6 +6,7 @@ obj-$(CONFIG_DEVFREQ_GOV_POWERSAVE)	+= governor_powersave.o
 obj-$(CONFIG_DEVFREQ_GOV_USERSPACE)	+= governor_userspace.o
 
 # DEVFREQ Drivers
+obj-$(CONFIG_ARCH_EXYNOS)		+= exynos/
 obj-$(CONFIG_ARM_EXYNOS4_BUS_DEVFREQ)	+= exynos/
 obj-$(CONFIG_ARM_EXYNOS5_BUS_DEVFREQ)	+= exynos/
 obj-$(CONFIG_ARM_TEGRA_DEVFREQ)		+= tegra-devfreq.o
diff --git a/drivers/devfreq/exynos/Makefile b/drivers/devfreq/exynos/Makefile
index 49bc9175f923..4ec06d322996 100644
--- a/drivers/devfreq/exynos/Makefile
+++ b/drivers/devfreq/exynos/Makefile
@@ -1,3 +1,4 @@
 # Exynos DEVFREQ Drivers
+obj-$(CONFIG_ARM_EXYNOS_BUS_DEVFREQ)	+= exynos-bus.o
 obj-$(CONFIG_ARM_EXYNOS4_BUS_DEVFREQ)	+= exynos_ppmu.o exynos4_bus.o
 obj-$(CONFIG_ARM_EXYNOS5_BUS_DEVFREQ)	+= exynos_ppmu.o exynos5_bus.o
diff --git a/drivers/devfreq/exynos/exynos-bus.c b/drivers/devfreq/exynos/exynos-bus.c
new file mode 100644
index 000000000000..577faa70b411
--- /dev/null
+++ b/drivers/devfreq/exynos/exynos-bus.c
@@ -0,0 +1,443 @@
+/*
+ * Generic Exynos Bus frequency driver with DEVFREQ Framework
+ *
+ * Copyright (c) 2015 Samsung Electronics Co., Ltd.
+ * Author : Chanwoo Choi <cw00.choi@samsung.com>
+ *
+ * This driver support Exynos Bus frequency feature by using
+ * DEVFREQ framework and is based on drivers/devfreq/exynos/exynos4_bus.c.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/devfreq.h>
+#include <linux/devfreq-event.h>
+#include <linux/device.h>
+#include <linux/export.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/pm_opp.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+
+#define DEFAULT_SATURATION_RATIO	40
+#define SAFEVOLT			50000
+
+struct exynos_bus {
+	struct device *dev;
+
+	struct devfreq *devfreq;
+	struct devfreq_event_dev **edev;
+	unsigned int edev_count;
+	struct mutex lock;
+
+	struct dev_pm_opp *curr_opp;
+
+	struct regulator *regulator;
+	struct clk *clk;
+	int ratio;
+};
+
+/*
+ * Control the devfreq-event device to get the current state of bus
+ */
+#define exynos_bus_ops_edev(ops)				\
+static int exynos_bus_##ops(struct exynos_bus *bus)		\
+{								\
+	int i, ret;						\
+								\
+	for (i = 0; i < bus->edev_count; i++) {			\
+		ret = devfreq_event_##ops(bus->edev[i]);	\
+		if (ret < 0)					\
+			return ret;				\
+	}							\
+								\
+	return 0;						\
+}
+exynos_bus_ops_edev(enable_edev);
+exynos_bus_ops_edev(disable_edev);
+exynos_bus_ops_edev(set_event);
+
+static int exynos_bus_get_event(struct exynos_bus *bus,
+				struct devfreq_event_data *edata)
+{
+	struct devfreq_event_data event_data;
+	unsigned long load_count = 0, total_count = 0;
+	int i, ret = 0;
+
+	for (i = 0; i < bus->edev_count; i++) {
+		ret = devfreq_event_get_event(bus->edev[i], &event_data);
+		if (ret < 0)
+			return ret;
+
+		if (i == 0 || event_data.load_count > load_count) {
+			load_count = event_data.load_count;
+			total_count = event_data.total_count;
+		}
+	}
+
+	edata->load_count = load_count;
+	edata->total_count = total_count;
+
+	return ret;
+}
+
+/*
+ * Must necessary function for devfreq governor
+ */
+static int exynos_bus_target(struct device *dev, unsigned long *freq, u32 flags)
+{
+	struct exynos_bus *bus = dev_get_drvdata(dev);
+	struct dev_pm_opp *new_opp;
+	unsigned long old_freq, new_freq, old_volt, new_volt;
+	int ret = 0;
+
+	/* Get new opp-bus instance according to new bus clock */
+	rcu_read_lock();
+	new_opp = devfreq_recommended_opp(dev, freq, flags);
+	if (IS_ERR_OR_NULL(new_opp)) {
+		dev_err(dev, "failed to get recommed opp instance\n");
+		rcu_read_unlock();
+		return PTR_ERR(new_opp);
+	}
+
+	new_freq = dev_pm_opp_get_freq(new_opp);
+	new_volt = dev_pm_opp_get_voltage(new_opp);
+	old_freq = dev_pm_opp_get_freq(bus->curr_opp);
+	old_volt = dev_pm_opp_get_voltage(bus->curr_opp);
+	rcu_read_unlock();
+
+	if (old_freq == new_freq)
+		return 0;
+
+	/* Change voltage and frequency according to new OPP level */
+	mutex_lock(&bus->lock);
+
+	if (old_freq < new_freq) {
+		ret = regulator_set_voltage(bus->regulator, new_volt,
+						new_volt + SAFEVOLT);
+		if (ret < 0) {
+			dev_err(bus->dev, "failed to set voltage\n");
+			regulator_set_voltage(bus->regulator, old_freq,
+						old_freq + SAFEVOLT);
+			goto out;
+		}
+	}
+
+	ret = clk_set_rate(bus->clk, new_freq);
+	if (ret < 0) {
+		dev_err(dev, "failed to change clock of bus\n");
+		clk_set_rate(bus->clk, old_freq);
+		goto out;
+	}
+
+	if (old_freq > new_freq) {
+		ret = regulator_set_voltage(bus->regulator, new_volt,
+						new_volt + SAFEVOLT);
+		if (ret < 0) {
+			dev_err(bus->dev, "failed to set voltage\n");
+			regulator_set_voltage(bus->regulator, old_freq,
+						old_freq + SAFEVOLT);
+			goto out;
+		}
+	}
+	bus->curr_opp = new_opp;
+
+	dev_dbg(dev, "Set the frequency of bus (%ldkHz -> %ldkHz)\n",
+			old_freq/1000, new_freq/1000);
+out:
+	mutex_unlock(&bus->lock);
+
+	return ret;
+}
+
+static int exynos_bus_get_dev_status(struct device *dev,
+				     struct devfreq_dev_status *stat)
+{
+	struct exynos_bus *bus = dev_get_drvdata(dev);
+	struct devfreq_event_data edata;
+	int ret;
+
+	rcu_read_lock();
+	stat->current_frequency = dev_pm_opp_get_freq(bus->curr_opp);
+	rcu_read_unlock();
+
+	ret = exynos_bus_get_event(bus, &edata);
+	if (ret < 0) {
+		stat->total_time = stat->busy_time = 0;
+		goto err;
+	}
+
+	stat->busy_time = (edata.load_count * 100) / bus->ratio;
+	stat->total_time = edata.total_count;
+
+	dev_dbg(dev, "Usage of devfreq-event : %ld/%ld\n", stat->busy_time,
+							stat->total_time);
+
+err:
+	ret = exynos_bus_set_event(bus);
+	if (ret < 0) {
+		dev_err(dev, "failed to set event to devfreq-event devices\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+static void exynos_bus_exit(struct device *dev)
+{
+	struct exynos_bus *bus = dev_get_drvdata(dev);
+	int ret;
+
+	ret = exynos_bus_disable_edev(bus);
+	if (ret < 0)
+		dev_warn(dev, "failed to disable the devfreq-event devices\n");
+
+	regulator_disable(bus->regulator);
+
+	dev_pm_opp_of_remove_table(dev);
+}
+
+static int exynos_bus_parse_of(struct device_node *np,
+			      struct exynos_bus *bus)
+{
+	struct device *dev = bus->dev;
+	unsigned long rate;
+	int i, ret, count, size;
+
+	/* Get the clock to provide each bus with source clock */
+	bus->clk = devm_clk_get(dev, "bus");
+	if (IS_ERR(bus->regulator)) {
+		dev_err(dev, "failed to get bus clock\n");
+		return PTR_ERR(bus->clk);
+	}
+
+	ret = clk_prepare_enable(bus->clk);
+	if (ret < 0) {
+		dev_err(dev, "failed to get enable clock\n");
+		return ret;
+	}
+
+	/* Get the freq/voltage OPP table to scale the bus frequency */
+	rcu_read_lock();
+	ret = dev_pm_opp_of_add_table(dev);
+	if (ret < 0) {
+		dev_err(dev, "failed to get OPP table\n");
+		rcu_read_unlock();
+		return ret;
+	}
+
+	rate = clk_get_rate(bus->clk);
+	bus->curr_opp = dev_pm_opp_find_freq_ceil(dev, &rate);
+	if (IS_ERR(bus->curr_opp)) {
+		dev_err(dev, "failed to find dev_pm_opp\n");
+		rcu_read_unlock();
+		ret = PTR_ERR(bus->curr_opp);
+		goto err_opp;
+	}
+	rcu_read_unlock();
+
+	/* Get the regulator to provide each bus with the power */
+	bus->regulator = devm_regulator_get(dev, "vdd");
+	if (IS_ERR(bus->regulator)) {
+		dev_err(dev, "failed to get VDD regulator\n");
+		ret = PTR_ERR(bus->regulator);
+		goto err_opp;
+	}
+
+	ret = regulator_enable(bus->regulator);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable VDD regulator\n");
+		goto err_opp;
+	}
+
+	/*
+	 * Get the devfreq-event devices to get the current utilization of
+	 * buses. This raw data will be used in devfreq ondemand governor.
+	 */
+	count = devfreq_event_get_edev_count(dev);
+	if (count < 0) {
+		dev_err(dev, "failed to get the count of devfreq-event dev\n");
+		ret = count;
+		goto err_regulator;
+	}
+	bus->edev_count = count;
+
+	size = sizeof(*bus->edev) * count;
+	bus->edev = devm_kzalloc(dev, size, GFP_KERNEL);
+	if (!bus->edev) {
+		ret = -ENOMEM;
+		goto err_regulator;
+	}
+
+	for (i = 0; i < count; i++) {
+		bus->edev[i] = devfreq_event_get_edev_by_phandle(dev, i);
+		if (IS_ERR(bus->edev[i])) {
+			ret = -EPROBE_DEFER;
+			goto err_regulator;
+		}
+	}
+
+	/*
+	 * Optionally, Get the saturation ratio according to Exynos SoC
+	 * When measuring the utilization of each AXI bus with devfreq-event
+	 * devices, the measured real cycle might be much lower than the
+	 * total cycle of bus during sampling rate. In result, the devfreq
+	 * simple-ondemand governor might not decide to change the current
+	 * frequency due to too utilization (= real cycle/total cycle).
+	 * So, this property is used to adjust the utilization when calculating
+	 * the busy_time in exynos_bus_get_dev_status().
+	 */
+	if (of_property_read_u32(np, "exynos,saturation-ratio", &bus->ratio))
+		bus->ratio = DEFAULT_SATURATION_RATIO;
+
+	return 0;
+
+err_regulator:
+	regulator_disable(bus->regulator);
+err_opp:
+	dev_pm_opp_of_remove_table(dev);
+
+	return ret;
+}
+
+static int exynos_bus_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct devfreq_dev_profile *profile;
+	struct devfreq_simple_ondemand_data *ondemand_data;
+	struct exynos_bus *bus;
+	int ret;
+
+	if (!np) {
+		dev_err(dev, "failed to find devicetree node\n");
+		return -EINVAL;
+	}
+
+	bus = devm_kzalloc(&pdev->dev, sizeof(*bus), GFP_KERNEL);
+	if (!bus)
+		return -ENOMEM;
+	mutex_init(&bus->lock);
+	bus->dev = &pdev->dev;
+	platform_set_drvdata(pdev, bus);
+
+	/* Parse the device-tree to get the resource information */
+	ret = exynos_bus_parse_of(np, bus);
+	if (ret < 0)
+		return ret;
+
+	/* Initalize the struct profile and governor data */
+	profile = devm_kzalloc(dev, sizeof(*profile), GFP_KERNEL);
+	if (!profile)
+		return -ENOMEM;
+	profile->polling_ms = 50;
+	profile->target = exynos_bus_target;
+	profile->get_dev_status = exynos_bus_get_dev_status;
+	profile->exit = exynos_bus_exit;
+
+	ondemand_data = devm_kzalloc(dev, sizeof(*ondemand_data), GFP_KERNEL);
+	if (!ondemand_data)
+		return -ENOMEM;
+	ondemand_data->upthreshold = 40;
+	ondemand_data->downdifferential = 5;
+
+	/* Add devfreq device to monitor and handle the exynos bus */
+	bus->devfreq = devm_devfreq_add_device(dev, profile, "simple_ondemand",
+						ondemand_data);
+	if (IS_ERR_OR_NULL(bus->devfreq)) {
+		dev_err(dev, "failed to add devfreq device\n");
+		return  PTR_ERR(bus->devfreq);
+	}
+
+	/* Register opp_notifier to catch the change of OPP  */
+	ret = devm_devfreq_register_opp_notifier(dev, bus->devfreq);
+	if (ret < 0) {
+		dev_err(dev, "failed to register opp notifier\n");
+		return ret;
+	}
+
+	/*
+	 * Enable devfreq-event to get raw data which is used to determine
+	 * current bus load.
+	 */
+	ret = exynos_bus_enable_edev(bus);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable devfreq-event devices\n");
+		return ret;
+	}
+
+	ret = exynos_bus_set_event(bus);
+	if (ret < 0) {
+		dev_err(dev, "failed to set event to devfreq-event devices\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int exynos_bus_resume(struct device *dev)
+{
+	struct exynos_bus *bus = dev_get_drvdata(dev);
+	int ret;
+
+	ret = regulator_enable(bus->regulator);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable VDD regulator\n");
+		return ret;
+	}
+
+	ret = exynos_bus_enable_edev(bus);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable the devfreq-event devices\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int exynos_bus_suspend(struct device *dev)
+{
+	struct exynos_bus *bus = dev_get_drvdata(dev);
+	int ret;
+
+	ret = exynos_bus_disable_edev(bus);
+	if (ret < 0) {
+		dev_err(dev, "failed to disable the devfreq-event devices\n");
+		return ret;
+	}
+
+	regulator_disable(bus->regulator);
+
+	return 0;
+}
+#endif
+
+static const struct dev_pm_ops exynos_bus_pm = {
+	SET_SYSTEM_SLEEP_PM_OPS(exynos_bus_suspend, exynos_bus_resume)
+};
+
+static const struct of_device_id exynos_bus_of_match[] = {
+	{ .compatible = "samsung,exynos-bus", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, exynos_bus_of_match);
+
+static struct platform_driver exynos_bus_platdrv = {
+	.probe		= exynos_bus_probe,
+	.driver = {
+		.name	= "exynos-bus",
+		.pm	= &exynos_bus_pm,
+		.of_match_table = of_match_ptr(exynos_bus_of_match),
+	},
+};
+module_platform_driver(exynos_bus_platdrv);
+
+MODULE_DESCRIPTION("Generic Exynos Bus frequency driver");
+MODULE_AUTHOR("Chanwoo Choi <cw00.choi@samsung.com>");
+MODULE_LICENSE("GPL v2");
-- 
1.9.1

[RFC PATCH 02/15] PM / devfreq: exynos: Add documentation for generic exynos bus frequency driver

[Chanwoo Choi]

This patch adds the documentation for generic exynos bus frequency
driver.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 .../devicetree/bindings/devfreq/exynos-bus.txt     | 92 ++++++++++++++++++++++
 1 file changed, 92 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/devfreq/exynos-bus.txt

diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
new file mode 100644
index 000000000000..5d90623bd173
--- /dev/null
+++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
@@ -0,0 +1,92 @@
+* Generic Exynos Bus frequency device
+
+The Samsung Exynos SoC have many buses for data transfer between DRAM
+and sub-blocks in SoC. Almost Exynos SoC have the common architecture
+for buses. Generally, the each bus of Exynos SoC includes the source clock
+and power line and then is able to change the clock according to the usage
+of each buses on runtime. When gathering the usage of each buses on runtime,
+thie driver uses the exynos-ppmu.c driver with DEVFREQ-EVENT framework.
+
+There are a little different composition among Exynos SoC because each Exynos
+SoC has the different sub-blocks. So, this difference should be specified
+in devicetree file instead of each device driver. In result, this driver
+is able to support the bus frequency for all Exynos SoCs.
+
+Required properties for bus device:
+- compatible: Should be "samsung,exynos-bus".
+- clock-names : the name of clock used by the bus, "bus".
+- clocks : phandles for clock specified in "clock-names" property.
+- #clock-cells: should be 1.
+- operating-points-v2: the OPP table including frequency/voltage information
+  to support DVFS (Dynamic Voltage/Frequency Scaling) feature.
+- vdd-supply: the regulator to provide the buses with the voltage.
+- devfreq-events: the devfreq-event device to monitor the curret utilization
+  of buses.
+
+Optional properties for bus device:
+- exynos,saturation-ratio: the percentage value which is used to calibrate
+                   the performance count againt total cycle count.
+
+Example1:
+	Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to
+	power line (regulator). The MIF (Memory Interface) AXI bus is used to
+	transfer data between DRAM and CPU and uses the VDD_MIF regualtor.
+
+	- power line(VDD_MIF) --> bus for DMC block (dmc clock)
+
+	- MIF bus's frequency/voltage table
+	-----------------------
+	|Lv| Freq   | Voltage |
+	-----------------------
+	|L1| 50000  |800000   |
+	|L2| 100000 |800000   |
+	|L3| 133000 |800000   |
+	|L4| 200000 |800000   |
+	|L5| 400000 |875000   |
+	-----------------------
+
+Example2 :
+	The bus of DMC block in exynos3250.dtsi are listed below:
+
+	bus_dmc: bus_dmc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_dmc CLK_DIV_DMC>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_dmc_opp_table>;
+		status = "disabled";
+	};
+
+	bus_dmc_opp_table: opp_table0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <50000000>;
+			opp-microvolt = <800000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <800000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <133000000>;
+			opp-microvolt = <800000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <800000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <875000>;
+		};
+	};
+
+	Usage case to handle the frequency and voltage of bus on runtime
+	in exynos3250-rinato.dts are listed below:
+
+	&bus_dmc {
+		devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
+		vdd-supply = <&buck1_reg>;	/* VDD_MIF */
+		status = "okay";
+	};
-- 
1.9.1

[RFC PATCH 03/15] ARM: dts: Add DMC bus node for Exynos3250

[Chanwoo Choi]

This patch adds the DMC (DRAM memory controller) bus node for Exynos3250 SoC.
The DMC is an AMBA AXI-compliant slave to interface external JEDEC standard
SDRAM devices. The bus includes the OPP tables and the source clock for DMC
block.

Following list specifies the detailed relation between the clock and DMC block:
- The source clock of DMC block : div_dmc

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 arch/arm/boot/dts/exynos3250.dtsi | 34 ++++++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/exynos3250.dtsi b/arch/arm/boot/dts/exynos3250.dtsi
index be0bb32c2d8c..45809f83c628 100644
--- a/arch/arm/boot/dts/exynos3250.dtsi
+++ b/arch/arm/boot/dts/exynos3250.dtsi
@@ -700,6 +700,40 @@
 			clock-names = "ppmu";
 			status = "disabled";
 		};
+
+		bus_dmc: bus_dmc {
+			compatible = "samsung,exynos-bus";
+			clocks = <&cmu_dmc CLK_DIV_DMC>;
+			clock-names = "bus";
+			operating-points-v2 = <&bus_dmc_opp_table>;
+			status = "disabled";
+		};
+
+		bus_dmc_opp_table: opp_table0 {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp00 {
+				opp-hz = /bits/ 64 <50000000>;
+				opp-microvolt = <800000>;
+			};
+			opp01 {
+				opp-hz = /bits/ 64 <100000000>;
+				opp-microvolt = <800000>;
+			};
+			opp02 {
+				opp-hz = /bits/ 64 <133000000>;
+				opp-microvolt = <800000>;
+			};
+			opp03 {
+				opp-hz = /bits/ 64 <200000000>;
+				opp-microvolt = <800000>;
+			};
+			opp04 {
+				opp-hz = /bits/ 64 <400000000>;
+				opp-microvolt = <875000>;
+			};
+		};
 	};
 };
 
-- 
1.9.1

[RFC PATCH 04/15] ARM: dts: Add DMC bus freqeuncy for exynos3250-rinato/monk

[Chanwoo Choi]

This patch adds the DMC (DRAM Memory Controller) bus frequency node
which includes the devfreq-events and regulator properties. The bus
frequency support the DVFS (Dynamic Voltage Frequency Scaling) feature
with ondemand governor.

The devfreq-events (ppmu_dmc0*) can monitor the utilization of DMC bus
on runtime and the buck1_reg (VDD_MIF power line) supplies the power to
the DMC block.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 arch/arm/boot/dts/exynos3250-monk.dts   | 6 ++++++
 arch/arm/boot/dts/exynos3250-rinato.dts | 6 ++++++
 2 files changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts
index 443a35085846..d982586a6533 100644
--- a/arch/arm/boot/dts/exynos3250-monk.dts
+++ b/arch/arm/boot/dts/exynos3250-monk.dts
@@ -498,6 +498,12 @@
 	};
 };
 
+&bus_dmc {
+	devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
+	vdd-supply = <&buck1_reg>;
+	status = "okay";
+};
+
 &xusbxti {
 	clock-frequency = <24000000>;
 };
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index 3e64d5dcdd60..61477943015b 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -675,6 +675,12 @@
 	};
 };
 
+&bus_dmc {
+	devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
+	vdd-supply = <&buck1_reg>;
+	status = "okay";
+};
+
 &xusbxti {
 	clock-frequency = <24000000>;
 };
-- 
1.9.1

[RFC PATCH 05/15] PM / devfreq: Add new passive governor

[Chanwoo Choi]

This patch adds the new passive governor for DEVFREQ framework. The following
governors are already present and used for DVFS (Dynamic Voltage and Frequency
Scaling) drivers. The following governors are independently used for one device
driver which don't give the influence to other device drviers and also don't
receive the effect from other device drivers.
- ondemand / performance / powersave / userspace

The passive governor depends on operation of parent driver with specific
governos extremely and is not able to decide the new frequency by oneself.
According to the decided new frequency of parent driver with governor,
the passive governor uses it to decide the appropriate frequency for own
device driver. The passive governor must need the following information
from device tree:
- the source clock and OPP tables
- the instance of parent device

For exameple,
there are one more devfreq device drivers which need to change their source
clock according to their utilization on runtime. But, they share the same
power line (e.g., regulator). So, specific device driver is operated as parent
with ondemand governor and then the rest device driver with passive governor
is influenced by parent device.

Suggested-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 drivers/devfreq/Kconfig            |   9 ++++
 drivers/devfreq/Makefile           |   1 +
 drivers/devfreq/devfreq.c          |  47 ++++++++++++++++
 drivers/devfreq/governor_passive.c | 108 +++++++++++++++++++++++++++++++++++++
 include/linux/devfreq.h            |  17 ++++++
 5 files changed, 182 insertions(+)
 create mode 100644 drivers/devfreq/governor_passive.c

diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
index 55ec774f794c..d03f635a93e1 100644
--- a/drivers/devfreq/Kconfig
+++ b/drivers/devfreq/Kconfig
@@ -64,6 +64,15 @@ config DEVFREQ_GOV_USERSPACE
 	  Otherwise, the governor does not change the frequnecy
 	  given at the initialization.
 
+config DEVFREQ_GOV_PASSIVE
+	tristate "Passive"
+	help
+	  Sets the frequency by other governors (simple_ondemand, performance,
+	  powersave, usersapce) of a parent devfreq device. This governor
+	  always has the dependency on the chosen frequency from paired
+	  governor. This governor does not change the frequency by oneself
+	  through sysfs entry.
+
 comment "DEVFREQ Drivers"
 
 config ARM_EXYNOS_BUS_DEVFREQ
diff --git a/drivers/devfreq/Makefile b/drivers/devfreq/Makefile
index 375ebbb4fcfb..f81c313b4b79 100644
--- a/drivers/devfreq/Makefile
+++ b/drivers/devfreq/Makefile
@@ -4,6 +4,7 @@ obj-$(CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND)	+= governor_simpleondemand.o
 obj-$(CONFIG_DEVFREQ_GOV_PERFORMANCE)	+= governor_performance.o
 obj-$(CONFIG_DEVFREQ_GOV_POWERSAVE)	+= governor_powersave.o
 obj-$(CONFIG_DEVFREQ_GOV_USERSPACE)	+= governor_userspace.o
+obj-$(CONFIG_DEVFREQ_GOV_PASSIVE)	+= governor_passive.o
 
 # DEVFREQ Drivers
 obj-$(CONFIG_ARCH_EXYNOS)		+= exynos/
diff --git a/drivers/devfreq/devfreq.c b/drivers/devfreq/devfreq.c
index 984c5e9e7bdd..15e58779e4c0 100644
--- a/drivers/devfreq/devfreq.c
+++ b/drivers/devfreq/devfreq.c
@@ -190,6 +190,31 @@ static struct devfreq_governor *find_devfreq_governor(const char *name)
 
 /* Load monitoring helper functions for governors use */
 
+static int update_devfreq_passive(struct devfreq *devfreq, unsigned long freq)
+{
+	struct devfreq *passive;
+	unsigned long rate;
+	int ret;
+
+	list_for_each_entry(passive, &devfreq->passive_dev_list, passive_node) {
+		if (!passive->governor)
+			continue;
+		rate = freq;
+
+		ret = passive->governor->get_target_freq(passive, &rate);
+		if (ret)
+			return ret;
+
+		ret = passive->profile->target(passive->dev.parent, &rate, 0);
+		if (ret)
+			return ret;
+
+		passive->previous_freq = rate;
+	}
+
+	return 0;
+}
+
 /**
  * update_devfreq() - Reevaluate the device and configure frequency.
  * @devfreq:	the devfreq instance.
@@ -233,10 +258,18 @@ int update_devfreq(struct devfreq *devfreq)
 		flags |= DEVFREQ_FLAG_LEAST_UPPER_BOUND; /* Use LUB */
 	}
 
+	if (!list_empty(&devfreq->passive_dev_list)
+		&& devfreq->previous_freq > freq)
+		update_devfreq_passive(devfreq, freq);
+
 	err = devfreq->profile->target(devfreq->dev.parent, &freq, flags);
 	if (err)
 		return err;
 
+	if (!list_empty(&devfreq->passive_dev_list)
+		&& devfreq->previous_freq < freq)
+		update_devfreq_passive(devfreq, freq);
+
 	if (devfreq->profile->freq_table)
 		if (devfreq_update_status(devfreq, freq))
 			dev_err(&devfreq->dev,
@@ -442,6 +475,10 @@ static void _remove_devfreq(struct devfreq *devfreq)
 		return;
 	}
 	list_del(&devfreq->node);
+	list_del(&devfreq->passive_node);
+	if (!list_empty(&devfreq->passive_dev_list))
+		list_del_init(&devfreq->passive_dev_list);
+
 	mutex_unlock(&devfreq_list_lock);
 
 	if (devfreq->governor)
@@ -559,6 +596,16 @@ struct devfreq *devfreq_add_device(struct device *dev,
 		goto err_init;
 	}
 
+	if (!strncmp(devfreq->governor_name, "passive", 7)) {
+		struct devfreq *parent_devfreq =
+			((struct devfreq_passive_data *)data)->parent;
+
+		list_add(&devfreq->passive_node,
+			&parent_devfreq->passive_dev_list);
+	} else {
+		INIT_LIST_HEAD(&devfreq->passive_dev_list);
+	}
+
 	return devfreq;
 
 err_init:
diff --git a/drivers/devfreq/governor_passive.c b/drivers/devfreq/governor_passive.c
new file mode 100644
index 000000000000..7443ae4b92f9
--- /dev/null
+++ b/drivers/devfreq/governor_passive.c
@@ -0,0 +1,108 @@
+/*
+ * linux/drivers/devfreq/governor_passive.c
+ *
+ * Copyright (C) 2015 Samsung Electronics
+ * Author: Chanwoo Choi <cw00.choi@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/devfreq.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/devfreq.h>
+#include "governor.h"
+
+static int devfreq_passive_get_target_freq(struct devfreq *passive,
+					unsigned long *freq)
+{
+	struct devfreq_passive_data *passive_data = passive->data;
+	struct devfreq *parent_devfreq = passive_data->parent;
+	unsigned long child_freq = ULONG_MAX;
+	int i, count;
+
+	/*
+	 * Each devfreq has the OPP table. After deciding the new frequency
+	 * from the governor of parent devfreq device, the passive governor
+	 * need to get the index of new frequency on OPP table of parent
+	 * device. And then the index is used for getting the suitable
+	 * new frequency for passive devfreq device.
+	 */
+
+	if (!passive->profile || !passive->profile->freq_table
+		|| passive->profile->max_state <= 0)
+		return -EINVAL;
+
+	/*
+	 * When new frequency is lower than previous frequency of parent
+	 * devfreq device, passive governor get the correct frequency from OPP
+	 * list of parent device. Because in this case, *freq is temporary
+	 * value which is decided by ondemand governor.
+	 */
+	if (parent_devfreq->previous_freq > *freq) {
+		struct dev_pm_opp *opp;
+		opp = devfreq_recommended_opp(parent_devfreq->dev.parent,
+						freq, 0);
+		if (IS_ERR_OR_NULL(opp))
+			return PTR_ERR(opp);
+	}
+
+	/*
+	 * Get the OPP table's index of decided freqeuncy by governor
+	 * of parent device.
+	 */
+	for (i = 0; i < parent_devfreq->profile->max_state; i++)
+		if (parent_devfreq->profile->freq_table[i] == *freq)
+			break;
+
+	if (i == parent_devfreq->profile->max_state)
+		return -EINVAL;
+	count = passive->profile->max_state;
+
+	/* Get the suitable frequency by using index of parent device. */
+	if (i < passive->profile->max_state)
+		child_freq = passive->profile->freq_table[i];
+	else
+		child_freq = passive->profile->freq_table[count - 1];
+
+	/* Return the suitable frequency for passive device. */
+	*freq = child_freq;
+
+	return 0;
+}
+
+static int devfreq_passive_event_handler(struct devfreq *devfreq,
+				unsigned int event, void *data)
+{
+	return 0;
+}
+
+static struct devfreq_governor devfreq_passive = {
+	.name = "passive",
+	.get_target_freq = devfreq_passive_get_target_freq,
+	.event_handler = devfreq_passive_event_handler,
+};
+
+static int __init devfreq_passive_init(void)
+{
+	return devfreq_add_governor(&devfreq_passive);
+}
+subsys_initcall(devfreq_passive_init);
+
+static void __exit devfreq_passive_exit(void)
+{
+	int ret;
+
+	ret = devfreq_remove_governor(&devfreq_passive);
+	if (ret)
+		pr_err("%s: failed remove governor %d\n", __func__, ret);
+
+	return;
+}
+module_exit(devfreq_passive_exit);
+
+MODULE_AUTHOR("Chanwoo Choi <cw00.choi@samsung.com>");
+MODULE_DESCRIPTION("DEVFREQ Passive governor");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/devfreq.h b/include/linux/devfreq.h
index 6fa02a20eb63..f7a6e6bd716e 100644
--- a/include/linux/devfreq.h
+++ b/include/linux/devfreq.h
@@ -177,6 +177,9 @@ struct devfreq {
 	unsigned int *trans_table;
 	unsigned long *time_in_state;
 	unsigned long last_stat_updated;
+
+	struct list_head passive_dev_list;
+	struct list_head passive_node;
 };
 
 #if defined(CONFIG_PM_DEVFREQ)
@@ -241,6 +244,20 @@ struct devfreq_simple_ondemand_data {
 };
 #endif
 
+#if IS_ENABLED(CONFIG_DEVFREQ_GOV_PASSIVE)
+/**
+ * struct devfreq_passive_data - void *data fed to struct devfreq
+ *	and devfreq_add_device
+ * @parent:		The parent devfreq device.
+ *
+ * If the fed devfreq_passive_data pointer is NULL to the governor,
+ * the governor return ERROR.
+ */
+struct devfreq_passive_data {
+	struct devfreq *parent;
+};
+#endif
+
 #else /* !CONFIG_PM_DEVFREQ */
 static inline struct devfreq *devfreq_add_device(struct device *dev,
 					  struct devfreq_dev_profile *profile,
-- 
1.9.1

[RFC PATCH 06/15] PM / devfreq: Add devfreq_get_devfreq_by_phandle()

[Chanwoo Choi]

This patch adds the new devfreq_get_devfreq_by_phandle() OF helper function
which can find the instance of devfreq device by using phandle ("devfreq").

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 drivers/devfreq/devfreq.c | 44 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/devfreq.h   |  9 +++++++++
 2 files changed, 53 insertions(+)

diff --git a/drivers/devfreq/devfreq.c b/drivers/devfreq/devfreq.c
index 15e58779e4c0..78ea4cdaa82c 100644
--- a/drivers/devfreq/devfreq.c
+++ b/drivers/devfreq/devfreq.c
@@ -25,6 +25,7 @@
 #include <linux/list.h>
 #include <linux/printk.h>
 #include <linux/hrtimer.h>
+#include <linux/of.h>
 #include "governor.h"
 
 static struct class *devfreq_class;
@@ -686,6 +687,49 @@ struct devfreq *devm_devfreq_add_device(struct device *dev,
 }
 EXPORT_SYMBOL(devm_devfreq_add_device);
 
+#ifdef CONFIG_OF
+/*
+ * devfreq_get_devfreq_by_phandle - Get the devfreq device from devicetree
+ * @dev - instance to the given device
+ * @index - index into list of devfreq
+ *
+ * return the instance of devfreq device
+ */
+struct devfreq *devfreq_get_devfreq_by_phandle(struct device *dev, int index)
+{
+	struct device_node *node;
+	struct devfreq *devfreq;
+
+	if (!dev)
+		return ERR_PTR(-EINVAL);
+
+	if (!dev->of_node)
+		return ERR_PTR(-EINVAL);
+
+	node = of_parse_phandle(dev->of_node, "devfreq", index);
+	if (!node)
+		return ERR_PTR(-ENODEV);
+
+	mutex_lock(&devfreq_list_lock);
+	list_for_each_entry(devfreq, &devfreq_list, node) {
+		if (devfreq->dev.parent
+			&& devfreq->dev.parent->of_node == node) {
+			mutex_unlock(&devfreq_list_lock);
+			return devfreq;
+		}
+	}
+	mutex_unlock(&devfreq_list_lock);
+
+	return ERR_PTR(-EPROBE_DEFER);
+}
+#else
+struct devfreq *devfreq_get_devfreq_by_phandle(struct device *dev, int index)
+{
+	return ERR_PTR(-ENODEV);
+}
+#endif /* CONFIG_OF */
+EXPORT_SYMBOL_GPL(devfreq_get_devfreq_by_phandle);
+
 /**
  * devm_devfreq_remove_device() - Resource-managed devfreq_remove_device()
  * @dev:	the device to add devfreq feature.
diff --git a/include/linux/devfreq.h b/include/linux/devfreq.h
index f7a6e6bd716e..d648041145ba 100644
--- a/include/linux/devfreq.h
+++ b/include/linux/devfreq.h
@@ -211,6 +211,9 @@ extern int devm_devfreq_register_opp_notifier(struct device *dev,
 extern void devm_devfreq_unregister_opp_notifier(struct device *dev,
 						struct devfreq *devfreq);
 
+extern struct devfreq *devfreq_get_devfreq_by_phandle(struct device *dev,
+						int index);
+
 /**
  * devfreq_update_stats() - update the last_status pointer in struct devfreq
  * @df:		the devfreq instance whose status needs updating
@@ -324,6 +327,12 @@ static inline void devm_devfreq_unregister_opp_notifier(struct device *dev,
 {
 }
 
+static inline struct devfreq *devfreq_get_devfreq_by_phandle(struct device *dev,
+							int index)
+{
+	return ERR_PTR(-ENODEV);
+}
+
 static inline int devfreq_update_stats(struct devfreq *df)
 {
 	return -EINVAL;
-- 
1.9.1

[RFC PATCH 07/15] PM / devfreq: Show the related information according to governor type

[Chanwoo Choi]

This patch modifies the following sysfs entry of DEVFREQ framework
because the devfreq device using passive governor don't need the same
information of the devfreq device using rest governor.
- polling_interval    : passive gov don't use the sampling rate.
- available_governors : passive gov don't be changed on runtime in this version.
- trans_stat          : passive governor don't support trans_stat in this version.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 drivers/devfreq/devfreq.c                 | 31 +++++++++++++++++++++++++------
 drivers/devfreq/governor.h                |  7 +++++++
 drivers/devfreq/governor_passive.c        |  1 +
 drivers/devfreq/governor_performance.c    |  1 +
 drivers/devfreq/governor_powersave.c      |  1 +
 drivers/devfreq/governor_simpleondemand.c |  1 +
 drivers/devfreq/governor_userspace.c      |  1 +
 include/linux/devfreq.h                   |  2 ++
 8 files changed, 39 insertions(+), 6 deletions(-)

diff --git a/drivers/devfreq/devfreq.c b/drivers/devfreq/devfreq.c
index 78ea4cdaa82c..18ad956fec93 100644
--- a/drivers/devfreq/devfreq.c
+++ b/drivers/devfreq/devfreq.c
@@ -597,7 +597,7 @@ struct devfreq *devfreq_add_device(struct device *dev,
 		goto err_init;
 	}
 
-	if (!strncmp(devfreq->governor_name, "passive", 7)) {
+	if (devfreq->governor->type == DEVFREQ_GOV_PASSIVE) {
 		struct devfreq *parent_devfreq =
 			((struct devfreq_passive_data *)data)->parent;
 
@@ -963,13 +963,23 @@ static ssize_t available_governors_show(struct device *d,
 					struct device_attribute *attr,
 					char *buf)
 {
-	struct devfreq_governor *tmp_governor;
+	struct devfreq *devfreq = to_devfreq(d);
 	ssize_t count = 0;
 
 	mutex_lock(&devfreq_list_lock);
-	list_for_each_entry(tmp_governor, &devfreq_governor_list, node)
+	if (devfreq->governor->type == DEVFREQ_GOV_PASSIVE) {
 		count += scnprintf(&buf[count], (PAGE_SIZE - count - 2),
-				   "%s ", tmp_governor->name);
+					   "%s ", devfreq->governor->name);
+	} else {
+		struct devfreq_governor *tmp_governor;
+
+		list_for_each_entry(tmp_governor, &devfreq_governor_list, node) {
+			if (tmp_governor->type == DEVFREQ_GOV_PASSIVE)
+				continue;
+			count += scnprintf(&buf[count], (PAGE_SIZE - count - 2),
+					   "%s ", tmp_governor->name);
+		}
+	}
 	mutex_unlock(&devfreq_list_lock);
 
 	/* Truncate the trailing space */
@@ -1006,6 +1016,11 @@ static DEVICE_ATTR_RO(target_freq);
 static ssize_t polling_interval_show(struct device *dev,
 				     struct device_attribute *attr, char *buf)
 {
+	struct devfreq *df = to_devfreq(dev);
+
+	if (df->governor->type == DEVFREQ_GOV_PASSIVE)
+		return sprintf(buf, "Not Supported.\n");
+
 	return sprintf(buf, "%d\n", to_devfreq(dev)->profile->polling_ms);
 }
 
@@ -1020,6 +1035,9 @@ static ssize_t polling_interval_store(struct device *dev,
 	if (!df->governor)
 		return -EINVAL;
 
+	if (df->governor->type == DEVFREQ_GOV_PASSIVE)
+		return -EINVAL;
+
 	ret = sscanf(buf, "%u", &value);
 	if (ret != 1)
 		return -EINVAL;
@@ -1137,11 +1155,12 @@ static ssize_t trans_stat_show(struct device *dev,
 	int i, j;
 	unsigned int max_state = devfreq->profile->max_state;
 
+	if (max_state == 0 || devfreq->governor->type == DEVFREQ_GOV_PASSIVE)
+		return sprintf(buf, "Not Supported.\n");
+
 	if (!devfreq->stop_polling &&
 			devfreq_update_status(devfreq, devfreq->previous_freq))
 		return 0;
-	if (max_state == 0)
-		return sprintf(buf, "Not Supported.\n");
 
 	len = sprintf(buf, "     From  :   To\n");
 	len += sprintf(buf + len, "           :");
diff --git a/drivers/devfreq/governor.h b/drivers/devfreq/governor.h
index fad7d6321978..43513a58f5bf 100644
--- a/drivers/devfreq/governor.h
+++ b/drivers/devfreq/governor.h
@@ -18,6 +18,13 @@
 
 #define to_devfreq(DEV)	container_of((DEV), struct devfreq, dev)
 
+/* Devfreq governor type */
+#define DEVFREQ_GOV_ONDEMAND			0x1
+#define DEVFREQ_GOV_PERFORMANCE			0x2
+#define DEVFREQ_GOV_POWERSAVE			0x3
+#define DEVFREQ_GOV_USERSPACE			0x4
+#define DEVFREQ_GOV_PASSIVE			0x4
+
 /* Devfreq events */
 #define DEVFREQ_GOV_START			0x1
 #define DEVFREQ_GOV_STOP			0x2
diff --git a/drivers/devfreq/governor_passive.c b/drivers/devfreq/governor_passive.c
index 7443ae4b92f9..adfdee9a9cd1 100644
--- a/drivers/devfreq/governor_passive.c
+++ b/drivers/devfreq/governor_passive.c
@@ -81,6 +81,7 @@ static int devfreq_passive_event_handler(struct devfreq *devfreq,
 
 static struct devfreq_governor devfreq_passive = {
 	.name = "passive",
+	.type = DEVFREQ_GOV_PASSIVE,
 	.get_target_freq = devfreq_passive_get_target_freq,
 	.event_handler = devfreq_passive_event_handler,
 };
diff --git a/drivers/devfreq/governor_performance.c b/drivers/devfreq/governor_performance.c
index c72f942f30a8..594d8ecb13fb 100644
--- a/drivers/devfreq/governor_performance.c
+++ b/drivers/devfreq/governor_performance.c
@@ -43,6 +43,7 @@ static int devfreq_performance_handler(struct devfreq *devfreq,
 
 static struct devfreq_governor devfreq_performance = {
 	.name = "performance",
+	.type = DEVFREQ_GOV_PERFORMANCE,
 	.get_target_freq = devfreq_performance_func,
 	.event_handler = devfreq_performance_handler,
 };
diff --git a/drivers/devfreq/governor_powersave.c b/drivers/devfreq/governor_powersave.c
index 0c6bed567e6d..e2817e1f2a31 100644
--- a/drivers/devfreq/governor_powersave.c
+++ b/drivers/devfreq/governor_powersave.c
@@ -40,6 +40,7 @@ static int devfreq_powersave_handler(struct devfreq *devfreq,
 
 static struct devfreq_governor devfreq_powersave = {
 	.name = "powersave",
+	.type = DEVFREQ_GOV_POWERSAVE,
 	.get_target_freq = devfreq_powersave_func,
 	.event_handler = devfreq_powersave_handler,
 };
diff --git a/drivers/devfreq/governor_simpleondemand.c b/drivers/devfreq/governor_simpleondemand.c
index ae72ba5e78df..b905a535d486 100644
--- a/drivers/devfreq/governor_simpleondemand.c
+++ b/drivers/devfreq/governor_simpleondemand.c
@@ -126,6 +126,7 @@ static int devfreq_simple_ondemand_handler(struct devfreq *devfreq,
 
 static struct devfreq_governor devfreq_simple_ondemand = {
 	.name = "simple_ondemand",
+	.type = DEVFREQ_GOV_ONDEMAND,
 	.get_target_freq = devfreq_simple_ondemand_func,
 	.event_handler = devfreq_simple_ondemand_handler,
 };
diff --git a/drivers/devfreq/governor_userspace.c b/drivers/devfreq/governor_userspace.c
index 35de6e83c1fe..c78ab78a5220 100644
--- a/drivers/devfreq/governor_userspace.c
+++ b/drivers/devfreq/governor_userspace.c
@@ -138,6 +138,7 @@ static int devfreq_userspace_handler(struct devfreq *devfreq,
 
 static struct devfreq_governor devfreq_userspace = {
 	.name = "userspace",
+	.type = DEVFREQ_GOV_USERSPACE,
 	.get_target_freq = devfreq_userspace_func,
 	.event_handler = devfreq_userspace_handler,
 };
diff --git a/include/linux/devfreq.h b/include/linux/devfreq.h
index d648041145ba..0c39022aaf2c 100644
--- a/include/linux/devfreq.h
+++ b/include/linux/devfreq.h
@@ -97,6 +97,7 @@ struct devfreq_dev_profile {
  * struct devfreq_governor - Devfreq policy governor
  * @node:		list node - contains registered devfreq governors
  * @name:		Governor's name
+ * @type:		Governor's type
  * @get_target_freq:	Returns desired operating frequency for the device.
  *			Basically, get_target_freq will run
  *			devfreq_dev_profile.get_dev_status() to get the
@@ -114,6 +115,7 @@ struct devfreq_governor {
 	struct list_head node;
 
 	const char name[DEVFREQ_NAME_LEN];
+	const int type;
 	int (*get_target_freq)(struct devfreq *this, unsigned long *freq);
 	int (*event_handler)(struct devfreq *devfreq,
 				unsigned int event, void *data);
-- 
1.9.1

[RFC PATCH 08/15] PM / devfreq: exynos: Add support of bus frequency of sub-blocks using passive governor

[Chanwoo Choi]

This patch adds the support of bus frequency feature for sub-blocks which share
the one power line. If each bus depends on the power line, each bus is not able
to change the voltage by oneself. To optimize the power-consumption on runtime,
some buses using the same power line should change the source clock and
regulator at the same time. So, this patch uses the passive governor to support
the bus frequency for all buses which sharing the one power line.

For example,

Exynos3250 include the two power line for AXI buses as following:
: VDD_MIF : MIF (Memory Interface) provide the DMC (Dynamic Memory Controller)
  with the power (regulator).
: VDD_INT : INT (Internal) provide the various sub-blocks with the power
  (regulator).

Each bus is included in as follwoing block. In the case of VDD_MIF, only DMC bus
use the power line. So, there is no any depencency between buese. But, in the
case of VDD_INT, various buses share the one power line of VDD_INT. We need to
make the depenency between buses. When using passive governor, there is no
problem to support the bus frequency as DVFS for all buses. One bus should be
operated as the parent bus device which gathering the current load of INT block
and then decides the new frequency with some governors except of passive
governor. After deciding the new frequency by the parent bus device, the rest
bus devices will change the each source clock according to new frequency of the
parent bus device.

- MIF (Memory Interface) block
: VDD_MIF |--- DMC

- INT (Internal) block
: VDD_INT |--- LEFTBUS  |--- PERIL
          |    (parent) |--- MFC
          |             |--- G3D
          |
          |--- RIGHTBUS |--- FSYS
                        |--- LCD0
                        |--- PERIR
                        |--- ISP
                        |--- CAM

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 drivers/devfreq/Kconfig             |   1 +
 drivers/devfreq/exynos/exynos-bus.c | 170 ++++++++++++++++++++++++++++--------
 2 files changed, 136 insertions(+), 35 deletions(-)

diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
index d03f635a93e1..88f7cc4539b8 100644
--- a/drivers/devfreq/Kconfig
+++ b/drivers/devfreq/Kconfig
@@ -79,6 +79,7 @@ config ARM_EXYNOS_BUS_DEVFREQ
 	bool "ARM EXYNOS Generic Memory Bus DEVFREQ Driver"
 	depends on ARCH_EXYNOS
 	select DEVFREQ_GOV_SIMPLE_ONDEMAND
+	select DEVFREQ_GOV_PASSIVE
 	select DEVFREQ_EVENT_EXYNOS_PPMU
 	select PM_DEVFREQ_EVENT
 	select PM_OPP
diff --git a/drivers/devfreq/exynos/exynos-bus.c b/drivers/devfreq/exynos/exynos-bus.c
index 577faa70b411..f318c3cc82ec 100644
--- a/drivers/devfreq/exynos/exynos-bus.c
+++ b/drivers/devfreq/exynos/exynos-bus.c
@@ -87,7 +87,7 @@ static int exynos_bus_get_event(struct exynos_bus *bus,
 }
 
 /*
- * Must necessary function for devfreq governor
+ * Must necessary function for devfreq simple-ondemand governor
  */
 static int exynos_bus_target(struct device *dev, unsigned long *freq, u32 flags)
 {
@@ -202,57 +202,74 @@ static void exynos_bus_exit(struct device *dev)
 	dev_pm_opp_of_remove_table(dev);
 }
 
-static int exynos_bus_parse_of(struct device_node *np,
-			      struct exynos_bus *bus)
+/*
+ * Must necessary function for devfreq passive governor
+ */
+static int exynos_bus_passive_target(struct device *dev, unsigned long *freq,
+					u32 flags)
 {
-	struct device *dev = bus->dev;
-	unsigned long rate;
-	int i, ret, count, size;
+	struct exynos_bus *bus = dev_get_drvdata(dev);
+	struct dev_pm_opp *new_opp;
+	unsigned long old_freq, new_freq;
+	int ret = 0;
 
-	/* Get the clock to provide each bus with source clock */
-	bus->clk = devm_clk_get(dev, "bus");
-	if (IS_ERR(bus->regulator)) {
-		dev_err(dev, "failed to get bus clock\n");
-		return PTR_ERR(bus->clk);
+	/* Get new opp-bus instance according to new bus clock */
+	rcu_read_lock();
+	new_opp = devfreq_recommended_opp(dev, freq, flags);
+	if (IS_ERR_OR_NULL(new_opp)) {
+		dev_err(dev, "failed to get recommed opp instance\n");
+		rcu_read_unlock();
+		return PTR_ERR(new_opp);
 	}
 
-	ret = clk_prepare_enable(bus->clk);
-	if (ret < 0) {
-		dev_err(dev, "failed to get enable clock\n");
-		return ret;
-	}
+	new_freq = dev_pm_opp_get_freq(new_opp);
+	old_freq = dev_pm_opp_get_freq(bus->curr_opp);
+	rcu_read_unlock();
 
-	/* Get the freq/voltage OPP table to scale the bus frequency */
-	rcu_read_lock();
-	ret = dev_pm_opp_of_add_table(dev);
+	if (old_freq == new_freq)
+		return 0;
+
+	/* Change the frequency according to new OPP level */
+	mutex_lock(&bus->lock);
+
+	ret = clk_set_rate(bus->clk, new_freq);
 	if (ret < 0) {
-		dev_err(dev, "failed to get OPP table\n");
-		rcu_read_unlock();
-		return ret;
+		dev_err(dev, "failed to set the clock of bus\n");
+		goto out;
 	}
 
-	rate = clk_get_rate(bus->clk);
-	bus->curr_opp = dev_pm_opp_find_freq_ceil(dev, &rate);
-	if (IS_ERR(bus->curr_opp)) {
-		dev_err(dev, "failed to find dev_pm_opp\n");
-		rcu_read_unlock();
-		ret = PTR_ERR(bus->curr_opp);
-		goto err_opp;
-	}
-	rcu_read_unlock();
+	bus->curr_opp = new_opp;
+
+	dev_info(dev, "Set the frequency of bus (%ldkHz -> %ldkHz)\n",
+			old_freq/1000, new_freq/1000);
+out:
+	mutex_unlock(&bus->lock);
+
+	return ret;
+}
+
+static void exynos_bus_passive_exit(struct device *dev)
+{
+	dev_pm_opp_of_remove_table(dev);
+}
+
+static int exynos_bus_parent_parse_of(struct device_node *np,
+					struct exynos_bus *bus)
+{
+	struct device *dev = bus->dev;
+	int i, ret, count, size;
 
 	/* Get the regulator to provide each bus with the power */
 	bus->regulator = devm_regulator_get(dev, "vdd");
 	if (IS_ERR(bus->regulator)) {
 		dev_err(dev, "failed to get VDD regulator\n");
-		ret = PTR_ERR(bus->regulator);
-		goto err_opp;
+		return PTR_ERR(bus->regulator);
 	}
 
 	ret = regulator_enable(bus->regulator);
 	if (ret < 0) {
 		dev_err(dev, "failed to enable VDD regulator\n");
-		goto err_opp;
+		return ret;
 	}
 
 	/*
@@ -299,6 +316,51 @@ static int exynos_bus_parse_of(struct device_node *np,
 
 err_regulator:
 	regulator_disable(bus->regulator);
+
+	return ret;
+}
+
+static int exynos_bus_parse_of(struct device_node *np,
+			      struct exynos_bus *bus)
+{
+	struct device *dev = bus->dev;
+	unsigned long rate;
+	int ret;
+
+	/* Get the clock to provide each bus with source clock */
+	bus->clk = devm_clk_get(dev, "bus");
+	if (IS_ERR(bus->regulator)) {
+		dev_err(dev, "failed to get bus clock\n");
+		return PTR_ERR(bus->clk);
+	}
+
+	ret = clk_prepare_enable(bus->clk);
+	if (ret < 0) {
+		dev_err(dev, "failed to get enable clock\n");
+		return ret;
+	}
+
+	/* Get the freq and voltage from OPP table to scale the bus freq */
+	rcu_read_lock();
+	ret = dev_pm_opp_of_add_table(dev);
+	if (ret < 0) {
+		dev_err(dev, "failed to get OPP table\n");
+		rcu_read_unlock();
+		return ret;
+	}
+
+	rate = clk_get_rate(bus->clk);
+	bus->curr_opp = dev_pm_opp_find_freq_ceil(dev, &rate);
+	if (IS_ERR(bus->curr_opp)) {
+		dev_err(dev, "failed to find dev_pm_opp\n");
+		rcu_read_unlock();
+		ret = PTR_ERR(bus->curr_opp);
+		goto err_opp;
+	}
+	rcu_read_unlock();
+
+	return 0;
+
 err_opp:
 	dev_pm_opp_of_remove_table(dev);
 
@@ -311,6 +373,8 @@ static int exynos_bus_probe(struct platform_device *pdev)
 	struct device_node *np = dev->of_node;
 	struct devfreq_dev_profile *profile;
 	struct devfreq_simple_ondemand_data *ondemand_data;
+	struct devfreq_passive_data *passive_data;
+	struct devfreq *parent_devfreq;
 	struct exynos_bus *bus;
 	int ret;
 
@@ -331,10 +395,19 @@ static int exynos_bus_probe(struct platform_device *pdev)
 	if (ret < 0)
 		return ret;
 
-	/* Initalize the struct profile and governor data */
 	profile = devm_kzalloc(dev, sizeof(*profile), GFP_KERNEL);
 	if (!profile)
 		return -ENOMEM;
+
+	if (of_parse_phandle(dev->of_node, "devfreq", 0))
+		goto passive;
+	else
+		ret = exynos_bus_parent_parse_of(np, bus);
+
+	if (ret < 0)
+		return ret;
+
+	/* Initalize the struct profile and governor data for parent device */
 	profile->polling_ms = 50;
 	profile->target = exynos_bus_target;
 	profile->get_dev_status = exynos_bus_get_dev_status;
@@ -378,6 +451,33 @@ static int exynos_bus_probe(struct platform_device *pdev)
 	}
 
 	return 0;
+
+passive:
+	/* Initalize the struct profile and governor data for passive device */
+	profile->target = exynos_bus_passive_target;
+	profile->exit = exynos_bus_passive_exit;
+
+	passive_data = devm_kzalloc(dev, sizeof(*passive_data), GFP_KERNEL);
+	if (!passive_data)
+		return -ENOMEM;
+
+	/* Get the instance of parent devfreq device */
+	parent_devfreq = devfreq_get_devfreq_by_phandle(dev, 0);
+	if (IS_ERR(parent_devfreq)) {
+		return -EPROBE_DEFER;
+	}
+	passive_data->parent = parent_devfreq;
+
+	/* Add devfreq device for exynos bus with passive governor */
+	bus->devfreq = devm_devfreq_add_device(dev, profile, "passive",
+						passive_data);
+	if (IS_ERR_OR_NULL(bus->devfreq)) {
+		dev_err(dev,
+			"failed to add devfreq dev with passive governor\n");
+		return -EPROBE_DEFER;
+	}
+
+	return 0;
 }
 
 #ifdef CONFIG_PM_SLEEP
-- 
1.9.1

[RFC PATCH 09/15] PM / devfreq: exynos: Update documentation for bus devices using passive governor

[Chanwoo Choi]

This patch updates the documentation for passive bus devices and adds the
detailed example of Exynos3250.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 .../devicetree/bindings/devfreq/exynos-bus.txt     | 226 ++++++++++++++++++++-
 1 file changed, 223 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
index 5d90623bd173..c4a6fe30075e 100644
--- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
+++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
@@ -12,18 +12,23 @@ SoC has the different sub-blocks. So, this difference should be specified
 in devicetree file instead of each device driver. In result, this driver
 is able to support the bus frequency for all Exynos SoCs.
 
-Required properties for bus device:
+Required properties for all bus devices:
 - compatible: Should be "samsung,exynos-bus".
 - clock-names : the name of clock used by the bus, "bus".
 - clocks : phandles for clock specified in "clock-names" property.
 - #clock-cells: should be 1.
 - operating-points-v2: the OPP table including frequency/voltage information
   to support DVFS (Dynamic Voltage/Frequency Scaling) feature.
+
+Required properties for only parent bus device:
 - vdd-supply: the regulator to provide the buses with the voltage.
 - devfreq-events: the devfreq-event device to monitor the curret utilization
   of buses.
 
-Optional properties for bus device:
+Required properties for only passive bus device:
+- devfreq: the parent bus device.
+
+Optional properties for only parent bus device:
 - exynos,saturation-ratio: the percentage value which is used to calibrate
                    the performance count againt total cycle count.
 
@@ -32,7 +37,19 @@ Example1:
 	power line (regulator). The MIF (Memory Interface) AXI bus is used to
 	transfer data between DRAM and CPU and uses the VDD_MIF regualtor.
 
-	- power line(VDD_MIF) --> bus for DMC block (dmc clock)
+	- MIF (Memory Interface) block
+	: VDD_MIF |--- DMC
+
+	- INT (Internal) block
+	: VDD_INT |--- LEFTBUS  |--- PERIL
+		  |    (parent) |--- MFC
+		  |             |--- G3D
+		  |
+		  |--- RIGHTBUS |--- FSYS
+				|--- LCD0
+				|--- PERIR
+				|--- ISP
+				|--- CAM
 
 	- MIF bus's frequency/voltage table
 	-----------------------
@@ -45,6 +62,20 @@ Example1:
 	|L5| 400000 |875000   |
 	-----------------------
 
+	- INT bus's frequency/voltage table
+	-----------------------------------------------------------------------
+	|Lv| Freq                                                   | Voltage |
+	-----------------------------------------------------------------------
+	|  |LEFTBUS|RIGHTBUS|LCD0   |FSYS   |MCUISP |ISP    |PERIL  |VDD_INT  |
+	|  |*parent|passive |passive|passive|passive|passive|passive|         |
+	-----------------------------------------------------------------------
+	|L1|50000  |50000   |50000  |50000  |50000  |50000  |50000  |900000   |
+	|L2|80000  |80000   |80000  |80000  |80000  |80000  |80000  |900000   |
+	|L3|100000 |100000  |100000 |100000 |100000 |100000 |100000 |1000000  |
+	|L4|133000 |133000  |133000 |133000 |200000 |200000 |       |1000000  |
+	|L5|200000 |200000  |200000 |200000 |400000 |300000 |       |1000000  |
+	-----------------------------------------------------------------------
+
 Example2 :
 	The bus of DMC block in exynos3250.dtsi are listed below:
 
@@ -82,6 +113,159 @@ Example2 :
 		};
 	};
 
+	bus_leftbus: bus_leftbus {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_GDL>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_rightbus: bus_rightbus {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_GDR>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_lcd0: bus_lcd0 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_ACLK_160>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_fsys: bus_fsys {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_ACLK_200>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_mcuisp: bus_mcuisp {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_ACLK_400_MCUISP>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_mcuisp_opp_table>;
+		status = "disabled";
+	};
+
+	bus_isp: bus_isp {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_ACLK_266>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_isp_opp_table>;
+		status = "disabled";
+	};
+
+	bus_peril: bus_perir {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu CLK_DIV_ACLK_100>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_peril_opp_table>;
+		status = "disabled";
+	};
+
+	bus_leftbus_opp_table: opp_table1 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <50000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <80000000>;
+			opp-microvolt = <900000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <133000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <1000000>;
+		};
+	};
+
+	bus_mcuisp_opp_table: opp_table2 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <50000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <80000000>;
+			opp-microvolt = <900000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <1000000>;
+		};
+	};
+
+	bus_isp_opp_table: opp_table3 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <50000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <80000000>;
+			opp-microvolt = <900000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <1000000>;
+		};
+	};
+
+	bus_peril_opp_table: opp_table4 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <50000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <80000000>;
+			opp-microvolt = <900000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <1000000>;
+		};
+	};
+
+
 	Usage case to handle the frequency and voltage of bus on runtime
 	in exynos3250-rinato.dts are listed below:
 
@@ -90,3 +274,39 @@ Example2 :
 		vdd-supply = <&buck1_reg>;	/* VDD_MIF */
 		status = "okay";
 	};
+
+	&bus_leftbus {
+		devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
+		vdd-supply = <&buck3_reg>;
+		status = "okay";
+	};
+
+	&bus_rightbus {
+		devfreq = <&bus_leftbus>;
+		status = "okay";
+	};
+
+	&bus_lcd0 {
+		devfreq = <&bus_leftbus>;
+		status = "okay";
+	};
+
+	&bus_fsys {
+		devfreq = <&bus_leftbus>;
+		status = "okay";
+	};
+
+	&bus_mcuisp {
+		devfreq = <&bus_leftbus>;
+		status = "okay";
+	};
+
+	&bus_isp {
+		devfreq = <&bus_leftbus>;
+		status = "okay";
+	};
+
+	&bus_peril {
+		devfreq = <&bus_leftbus>;
+		status = "okay";
+	};
-- 
1.9.1

[RFC PATCH 10/15] PM / devfreq: exynos: Remove unused exynos4/5 busfreq driver

[Chanwoo Choi]

This patch removes the unused exynos4/5 busfreq driver. Instead,
generic exynos-bus frequency driver support the all Exynos SoCs.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 drivers/devfreq/Kconfig              |   22 -
 drivers/devfreq/exynos/Makefile      |    2 -
 drivers/devfreq/exynos/exynos4_bus.c | 1055 ----------------------------------
 drivers/devfreq/exynos/exynos4_bus.h |  110 ----
 drivers/devfreq/exynos/exynos5_bus.c |  431 --------------
 drivers/devfreq/exynos/exynos_ppmu.c |  119 ----
 drivers/devfreq/exynos/exynos_ppmu.h |   86 ---
 7 files changed, 1825 deletions(-)
 delete mode 100644 drivers/devfreq/exynos/exynos4_bus.c
 delete mode 100644 drivers/devfreq/exynos/exynos4_bus.h
 delete mode 100644 drivers/devfreq/exynos/exynos5_bus.c
 delete mode 100644 drivers/devfreq/exynos/exynos_ppmu.c
 delete mode 100644 drivers/devfreq/exynos/exynos_ppmu.h

diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
index 88f7cc4539b8..e82b1d8cd200 100644
--- a/drivers/devfreq/Kconfig
+++ b/drivers/devfreq/Kconfig
@@ -91,28 +91,6 @@ config ARM_EXYNOS_BUS_DEVFREQ
 	  and adjusts the operating frequencies and voltages with OPP support.
 	  This does not yet operate with optimal voltages.
 
-config ARM_EXYNOS4_BUS_DEVFREQ
-	bool "ARM Exynos4210/4212/4412 Memory Bus DEVFREQ Driver"
-	depends on (CPU_EXYNOS4210 || SOC_EXYNOS4212 || SOC_EXYNOS4412) && !ARCH_MULTIPLATFORM
-	select DEVFREQ_GOV_SIMPLE_ONDEMAND
-	select PM_OPP
-	help
-	  This adds the DEVFREQ driver for Exynos4210 memory bus (vdd_int)
-	  and Exynos4212/4412 memory interface and bus (vdd_mif + vdd_int).
-	  It reads PPMU counters of memory controllers and adjusts
-	  the operating frequencies and voltages with OPP support.
-	  This does not yet operate with optimal voltages.
-
-config ARM_EXYNOS5_BUS_DEVFREQ
-	tristate "ARM Exynos5250 Bus DEVFREQ Driver"
-	depends on SOC_EXYNOS5250
-	select DEVFREQ_GOV_SIMPLE_ONDEMAND
-	select PM_OPP
-	help
-	  This adds the DEVFREQ driver for Exynos5250 bus interface (vdd_int).
-	  It reads PPMU counters of memory controllers and adjusts the
-	  operating frequencies and voltages with OPP support.
-
 config ARM_TEGRA_DEVFREQ
        tristate "Tegra DEVFREQ Driver"
        depends on ARCH_TEGRA_124_SOC
diff --git a/drivers/devfreq/exynos/Makefile b/drivers/devfreq/exynos/Makefile
index 4ec06d322996..bc695ad81c7d 100644
--- a/drivers/devfreq/exynos/Makefile
+++ b/drivers/devfreq/exynos/Makefile
@@ -1,4 +1,2 @@
 # Exynos DEVFREQ Drivers
 obj-$(CONFIG_ARM_EXYNOS_BUS_DEVFREQ)	+= exynos-bus.o
-obj-$(CONFIG_ARM_EXYNOS4_BUS_DEVFREQ)	+= exynos_ppmu.o exynos4_bus.o
-obj-$(CONFIG_ARM_EXYNOS5_BUS_DEVFREQ)	+= exynos_ppmu.o exynos5_bus.o
diff --git a/drivers/devfreq/exynos/exynos4_bus.c b/drivers/devfreq/exynos/exynos4_bus.c
deleted file mode 100644
index da9509205169..000000000000
--- a/drivers/devfreq/exynos/exynos4_bus.c
+++ /dev/null
@@ -1,1055 +0,0 @@
-/* drivers/devfreq/exynos4210_memorybus.c
- *
- * Copyright (c) 2011 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *	MyungJoo Ham <myungjoo.ham@samsung.com>
- *
- * EXYNOS4 - Memory/Bus clock frequency scaling support in DEVFREQ framework
- *	This version supports EXYNOS4210 only. This changes bus frequencies
- *	and vddint voltages. Exynos4412/4212 should be able to be supported
- *	with minor modifications.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/io.h>
-#include <linux/slab.h>
-#include <linux/mutex.h>
-#include <linux/suspend.h>
-#include <linux/pm_opp.h>
-#include <linux/devfreq.h>
-#include <linux/platform_device.h>
-#include <linux/regulator/consumer.h>
-#include <linux/module.h>
-
-#include <mach/map.h>
-
-#include "exynos_ppmu.h"
-#include "exynos4_bus.h"
-
-#define MAX_SAFEVOLT	1200000 /* 1.2V */
-
-enum exynos4_busf_type {
-	TYPE_BUSF_EXYNOS4210,
-	TYPE_BUSF_EXYNOS4x12,
-};
-
-/* Assume that the bus is saturated if the utilization is 40% */
-#define BUS_SATURATION_RATIO	40
-
-enum busclk_level_idx {
-	LV_0 = 0,
-	LV_1,
-	LV_2,
-	LV_3,
-	LV_4,
-	_LV_END
-};
-
-enum exynos_ppmu_idx {
-	PPMU_DMC0,
-	PPMU_DMC1,
-	PPMU_END,
-};
-
-#define EX4210_LV_MAX	LV_2
-#define EX4x12_LV_MAX	LV_4
-#define EX4210_LV_NUM	(LV_2 + 1)
-#define EX4x12_LV_NUM	(LV_4 + 1)
-
-/**
- * struct busfreq_opp_info - opp information for bus
- * @rate:	Frequency in hertz
- * @volt:	Voltage in microvolts corresponding to this OPP
- */
-struct busfreq_opp_info {
-	unsigned long rate;
-	unsigned long volt;
-};
-
-struct busfreq_data {
-	enum exynos4_busf_type type;
-	struct device *dev;
-	struct devfreq *devfreq;
-	bool disabled;
-	struct regulator *vdd_int;
-	struct regulator *vdd_mif; /* Exynos4412/4212 only */
-	struct busfreq_opp_info curr_oppinfo;
-	struct busfreq_ppmu_data ppmu_data;
-
-	struct notifier_block pm_notifier;
-	struct mutex lock;
-
-	/* Dividers calculated at boot/probe-time */
-	unsigned int dmc_divtable[_LV_END]; /* DMC0 */
-	unsigned int top_divtable[_LV_END];
-};
-
-/* 4210 controls clock of mif and voltage of int */
-static struct bus_opp_table exynos4210_busclk_table[] = {
-	{LV_0, 400000, 1150000},
-	{LV_1, 267000, 1050000},
-	{LV_2, 133000, 1025000},
-	{0, 0, 0},
-};
-
-/*
- * MIF is the main control knob clock for Exynos4x12 MIF/INT
- * clock and voltage of both mif/int are controlled.
- */
-static struct bus_opp_table exynos4x12_mifclk_table[] = {
-	{LV_0, 400000, 1100000},
-	{LV_1, 267000, 1000000},
-	{LV_2, 160000, 950000},
-	{LV_3, 133000, 950000},
-	{LV_4, 100000, 950000},
-	{0, 0, 0},
-};
-
-/*
- * INT is not the control knob of 4x12. LV_x is not meant to represent
- * the current performance. (MIF does)
- */
-static struct bus_opp_table exynos4x12_intclk_table[] = {
-	{LV_0, 200000, 1000000},
-	{LV_1, 160000, 950000},
-	{LV_2, 133000, 925000},
-	{LV_3, 100000, 900000},
-	{0, 0, 0},
-};
-
-/* TODO: asv volt definitions are "__initdata"? */
-/* Some chips have different operating voltages */
-static unsigned int exynos4210_asv_volt[][EX4210_LV_NUM] = {
-	{1150000, 1050000, 1050000},
-	{1125000, 1025000, 1025000},
-	{1100000, 1000000, 1000000},
-	{1075000, 975000, 975000},
-	{1050000, 950000, 950000},
-};
-
-static unsigned int exynos4x12_mif_step_50[][EX4x12_LV_NUM] = {
-	/* 400      267     160     133     100 */
-	{1050000, 950000, 900000, 900000, 900000}, /* ASV0 */
-	{1050000, 950000, 900000, 900000, 900000}, /* ASV1 */
-	{1050000, 950000, 900000, 900000, 900000}, /* ASV2 */
-	{1050000, 900000, 900000, 900000, 900000}, /* ASV3 */
-	{1050000, 900000, 900000, 900000, 850000}, /* ASV4 */
-	{1050000, 900000, 900000, 850000, 850000}, /* ASV5 */
-	{1050000, 900000, 850000, 850000, 850000}, /* ASV6 */
-	{1050000, 900000, 850000, 850000, 850000}, /* ASV7 */
-	{1050000, 900000, 850000, 850000, 850000}, /* ASV8 */
-};
-
-static unsigned int exynos4x12_int_volt[][EX4x12_LV_NUM] = {
-	/* 200    160      133     100 */
-	{1000000, 950000, 925000, 900000}, /* ASV0 */
-	{975000,  925000, 925000, 900000}, /* ASV1 */
-	{950000,  925000, 900000, 875000}, /* ASV2 */
-	{950000,  900000, 900000, 875000}, /* ASV3 */
-	{925000,  875000, 875000, 875000}, /* ASV4 */
-	{900000,  850000, 850000, 850000}, /* ASV5 */
-	{900000,  850000, 850000, 850000}, /* ASV6 */
-	{900000,  850000, 850000, 850000}, /* ASV7 */
-	{900000,  850000, 850000, 850000}, /* ASV8 */
-};
-
-/*** Clock Divider Data for Exynos4210 ***/
-static unsigned int exynos4210_clkdiv_dmc0[][8] = {
-	/*
-	 * Clock divider value for following
-	 * { DIVACP, DIVACP_PCLK, DIVDPHY, DIVDMC, DIVDMCD
-	 *		DIVDMCP, DIVCOPY2, DIVCORE_TIMERS }
-	 */
-
-	/* DMC L0: 400MHz */
-	{ 3, 1, 1, 1, 1, 1, 3, 1 },
-	/* DMC L1: 266.7MHz */
-	{ 4, 1, 1, 2, 1, 1, 3, 1 },
-	/* DMC L2: 133MHz */
-	{ 5, 1, 1, 5, 1, 1, 3, 1 },
-};
-static unsigned int exynos4210_clkdiv_top[][5] = {
-	/*
-	 * Clock divider value for following
-	 * { DIVACLK200, DIVACLK100, DIVACLK160, DIVACLK133, DIVONENAND }
-	 */
-	/* ACLK200 L0: 200MHz */
-	{ 3, 7, 4, 5, 1 },
-	/* ACLK200 L1: 160MHz */
-	{ 4, 7, 5, 6, 1 },
-	/* ACLK200 L2: 133MHz */
-	{ 5, 7, 7, 7, 1 },
-};
-static unsigned int exynos4210_clkdiv_lr_bus[][2] = {
-	/*
-	 * Clock divider value for following
-	 * { DIVGDL/R, DIVGPL/R }
-	 */
-	/* ACLK_GDL/R L1: 200MHz */
-	{ 3, 1 },
-	/* ACLK_GDL/R L2: 160MHz */
-	{ 4, 1 },
-	/* ACLK_GDL/R L3: 133MHz */
-	{ 5, 1 },
-};
-
-/*** Clock Divider Data for Exynos4212/4412 ***/
-static unsigned int exynos4x12_clkdiv_dmc0[][6] = {
-	/*
-	 * Clock divider value for following
-	 * { DIVACP, DIVACP_PCLK, DIVDPHY, DIVDMC, DIVDMCD
-	 *              DIVDMCP}
-	 */
-
-	/* DMC L0: 400MHz */
-	{3, 1, 1, 1, 1, 1},
-	/* DMC L1: 266.7MHz */
-	{4, 1, 1, 2, 1, 1},
-	/* DMC L2: 160MHz */
-	{5, 1, 1, 4, 1, 1},
-	/* DMC L3: 133MHz */
-	{5, 1, 1, 5, 1, 1},
-	/* DMC L4: 100MHz */
-	{7, 1, 1, 7, 1, 1},
-};
-static unsigned int exynos4x12_clkdiv_dmc1[][6] = {
-	/*
-	 * Clock divider value for following
-	 * { G2DACP, DIVC2C, DIVC2C_ACLK }
-	 */
-
-	/* DMC L0: 400MHz */
-	{3, 1, 1},
-	/* DMC L1: 266.7MHz */
-	{4, 2, 1},
-	/* DMC L2: 160MHz */
-	{5, 4, 1},
-	/* DMC L3: 133MHz */
-	{5, 5, 1},
-	/* DMC L4: 100MHz */
-	{7, 7, 1},
-};
-static unsigned int exynos4x12_clkdiv_top[][5] = {
-	/*
-	 * Clock divider value for following
-	 * { DIVACLK266_GPS, DIVACLK100, DIVACLK160,
-		DIVACLK133, DIVONENAND }
-	 */
-
-	/* ACLK_GDL/R L0: 200MHz */
-	{2, 7, 4, 5, 1},
-	/* ACLK_GDL/R L1: 200MHz */
-	{2, 7, 4, 5, 1},
-	/* ACLK_GDL/R L2: 160MHz */
-	{4, 7, 5, 7, 1},
-	/* ACLK_GDL/R L3: 133MHz */
-	{4, 7, 5, 7, 1},
-	/* ACLK_GDL/R L4: 100MHz */
-	{7, 7, 7, 7, 1},
-};
-static unsigned int exynos4x12_clkdiv_lr_bus[][2] = {
-	/*
-	 * Clock divider value for following
-	 * { DIVGDL/R, DIVGPL/R }
-	 */
-
-	/* ACLK_GDL/R L0: 200MHz */
-	{3, 1},
-	/* ACLK_GDL/R L1: 200MHz */
-	{3, 1},
-	/* ACLK_GDL/R L2: 160MHz */
-	{4, 1},
-	/* ACLK_GDL/R L3: 133MHz */
-	{5, 1},
-	/* ACLK_GDL/R L4: 100MHz */
-	{7, 1},
-};
-static unsigned int exynos4x12_clkdiv_sclkip[][3] = {
-	/*
-	 * Clock divider value for following
-	 * { DIVMFC, DIVJPEG, DIVFIMC0~3}
-	 */
-
-	/* SCLK_MFC: 200MHz */
-	{3, 3, 4},
-	/* SCLK_MFC: 200MHz */
-	{3, 3, 4},
-	/* SCLK_MFC: 160MHz */
-	{4, 4, 5},
-	/* SCLK_MFC: 133MHz */
-	{5, 5, 5},
-	/* SCLK_MFC: 100MHz */
-	{7, 7, 7},
-};
-
-
-static int exynos4210_set_busclk(struct busfreq_data *data,
-				 struct busfreq_opp_info *oppi)
-{
-	unsigned int index;
-	unsigned int tmp;
-
-	for (index = LV_0; index < EX4210_LV_NUM; index++)
-		if (oppi->rate == exynos4210_busclk_table[index].clk)
-			break;
-
-	if (index == EX4210_LV_NUM)
-		return -EINVAL;
-
-	/* Change Divider - DMC0 */
-	tmp = data->dmc_divtable[index];
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_DMC0);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_DMC0);
-	} while (tmp & 0x11111111);
-
-	/* Change Divider - TOP */
-	tmp = data->top_divtable[index];
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_TOP);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_TOP);
-	} while (tmp & 0x11111);
-
-	/* Change Divider - LEFTBUS */
-	tmp = __raw_readl(EXYNOS4_CLKDIV_LEFTBUS);
-
-	tmp &= ~(EXYNOS4_CLKDIV_BUS_GDLR_MASK | EXYNOS4_CLKDIV_BUS_GPLR_MASK);
-
-	tmp |= ((exynos4210_clkdiv_lr_bus[index][0] <<
-				EXYNOS4_CLKDIV_BUS_GDLR_SHIFT) |
-		(exynos4210_clkdiv_lr_bus[index][1] <<
-				EXYNOS4_CLKDIV_BUS_GPLR_SHIFT));
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_LEFTBUS);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_LEFTBUS);
-	} while (tmp & 0x11);
-
-	/* Change Divider - RIGHTBUS */
-	tmp = __raw_readl(EXYNOS4_CLKDIV_RIGHTBUS);
-
-	tmp &= ~(EXYNOS4_CLKDIV_BUS_GDLR_MASK | EXYNOS4_CLKDIV_BUS_GPLR_MASK);
-
-	tmp |= ((exynos4210_clkdiv_lr_bus[index][0] <<
-				EXYNOS4_CLKDIV_BUS_GDLR_SHIFT) |
-		(exynos4210_clkdiv_lr_bus[index][1] <<
-				EXYNOS4_CLKDIV_BUS_GPLR_SHIFT));
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_RIGHTBUS);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_RIGHTBUS);
-	} while (tmp & 0x11);
-
-	return 0;
-}
-
-static int exynos4x12_set_busclk(struct busfreq_data *data,
-				 struct busfreq_opp_info *oppi)
-{
-	unsigned int index;
-	unsigned int tmp;
-
-	for (index = LV_0; index < EX4x12_LV_NUM; index++)
-		if (oppi->rate == exynos4x12_mifclk_table[index].clk)
-			break;
-
-	if (index == EX4x12_LV_NUM)
-		return -EINVAL;
-
-	/* Change Divider - DMC0 */
-	tmp = data->dmc_divtable[index];
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_DMC0);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_DMC0);
-	} while (tmp & 0x11111111);
-
-	/* Change Divider - DMC1 */
-	tmp = __raw_readl(EXYNOS4_CLKDIV_DMC1);
-
-	tmp &= ~(EXYNOS4_CLKDIV_DMC1_G2D_ACP_MASK |
-		EXYNOS4_CLKDIV_DMC1_C2C_MASK |
-		EXYNOS4_CLKDIV_DMC1_C2CACLK_MASK);
-
-	tmp |= ((exynos4x12_clkdiv_dmc1[index][0] <<
-				EXYNOS4_CLKDIV_DMC1_G2D_ACP_SHIFT) |
-		(exynos4x12_clkdiv_dmc1[index][1] <<
-				EXYNOS4_CLKDIV_DMC1_C2C_SHIFT) |
-		(exynos4x12_clkdiv_dmc1[index][2] <<
-				EXYNOS4_CLKDIV_DMC1_C2CACLK_SHIFT));
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_DMC1);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_DMC1);
-	} while (tmp & 0x111111);
-
-	/* Change Divider - TOP */
-	tmp = __raw_readl(EXYNOS4_CLKDIV_TOP);
-
-	tmp &= ~(EXYNOS4_CLKDIV_TOP_ACLK266_GPS_MASK |
-		EXYNOS4_CLKDIV_TOP_ACLK100_MASK |
-		EXYNOS4_CLKDIV_TOP_ACLK160_MASK |
-		EXYNOS4_CLKDIV_TOP_ACLK133_MASK |
-		EXYNOS4_CLKDIV_TOP_ONENAND_MASK);
-
-	tmp |= ((exynos4x12_clkdiv_top[index][0] <<
-				EXYNOS4_CLKDIV_TOP_ACLK266_GPS_SHIFT) |
-		(exynos4x12_clkdiv_top[index][1] <<
-				EXYNOS4_CLKDIV_TOP_ACLK100_SHIFT) |
-		(exynos4x12_clkdiv_top[index][2] <<
-				EXYNOS4_CLKDIV_TOP_ACLK160_SHIFT) |
-		(exynos4x12_clkdiv_top[index][3] <<
-				EXYNOS4_CLKDIV_TOP_ACLK133_SHIFT) |
-		(exynos4x12_clkdiv_top[index][4] <<
-				EXYNOS4_CLKDIV_TOP_ONENAND_SHIFT));
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_TOP);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_TOP);
-	} while (tmp & 0x11111);
-
-	/* Change Divider - LEFTBUS */
-	tmp = __raw_readl(EXYNOS4_CLKDIV_LEFTBUS);
-
-	tmp &= ~(EXYNOS4_CLKDIV_BUS_GDLR_MASK | EXYNOS4_CLKDIV_BUS_GPLR_MASK);
-
-	tmp |= ((exynos4x12_clkdiv_lr_bus[index][0] <<
-				EXYNOS4_CLKDIV_BUS_GDLR_SHIFT) |
-		(exynos4x12_clkdiv_lr_bus[index][1] <<
-				EXYNOS4_CLKDIV_BUS_GPLR_SHIFT));
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_LEFTBUS);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_LEFTBUS);
-	} while (tmp & 0x11);
-
-	/* Change Divider - RIGHTBUS */
-	tmp = __raw_readl(EXYNOS4_CLKDIV_RIGHTBUS);
-
-	tmp &= ~(EXYNOS4_CLKDIV_BUS_GDLR_MASK | EXYNOS4_CLKDIV_BUS_GPLR_MASK);
-
-	tmp |= ((exynos4x12_clkdiv_lr_bus[index][0] <<
-				EXYNOS4_CLKDIV_BUS_GDLR_SHIFT) |
-		(exynos4x12_clkdiv_lr_bus[index][1] <<
-				EXYNOS4_CLKDIV_BUS_GPLR_SHIFT));
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_RIGHTBUS);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_RIGHTBUS);
-	} while (tmp & 0x11);
-
-	/* Change Divider - MFC */
-	tmp = __raw_readl(EXYNOS4_CLKDIV_MFC);
-
-	tmp &= ~(EXYNOS4_CLKDIV_MFC_MASK);
-
-	tmp |= ((exynos4x12_clkdiv_sclkip[index][0] <<
-				EXYNOS4_CLKDIV_MFC_SHIFT));
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_MFC);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_MFC);
-	} while (tmp & 0x1);
-
-	/* Change Divider - JPEG */
-	tmp = __raw_readl(EXYNOS4_CLKDIV_CAM1);
-
-	tmp &= ~(EXYNOS4_CLKDIV_CAM1_JPEG_MASK);
-
-	tmp |= ((exynos4x12_clkdiv_sclkip[index][1] <<
-				EXYNOS4_CLKDIV_CAM1_JPEG_SHIFT));
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_CAM1);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_CAM1);
-	} while (tmp & 0x1);
-
-	/* Change Divider - FIMC0~3 */
-	tmp = __raw_readl(EXYNOS4_CLKDIV_CAM);
-
-	tmp &= ~(EXYNOS4_CLKDIV_CAM_FIMC0_MASK | EXYNOS4_CLKDIV_CAM_FIMC1_MASK |
-		EXYNOS4_CLKDIV_CAM_FIMC2_MASK | EXYNOS4_CLKDIV_CAM_FIMC3_MASK);
-
-	tmp |= ((exynos4x12_clkdiv_sclkip[index][2] <<
-				EXYNOS4_CLKDIV_CAM_FIMC0_SHIFT) |
-		(exynos4x12_clkdiv_sclkip[index][2] <<
-				EXYNOS4_CLKDIV_CAM_FIMC1_SHIFT) |
-		(exynos4x12_clkdiv_sclkip[index][2] <<
-				EXYNOS4_CLKDIV_CAM_FIMC2_SHIFT) |
-		(exynos4x12_clkdiv_sclkip[index][2] <<
-				EXYNOS4_CLKDIV_CAM_FIMC3_SHIFT));
-
-	__raw_writel(tmp, EXYNOS4_CLKDIV_CAM);
-
-	do {
-		tmp = __raw_readl(EXYNOS4_CLKDIV_STAT_CAM1);
-	} while (tmp & 0x1111);
-
-	return 0;
-}
-
-static int exynos4x12_get_intspec(unsigned long mifclk)
-{
-	int i = 0;
-
-	while (exynos4x12_intclk_table[i].clk) {
-		if (exynos4x12_intclk_table[i].clk <= mifclk)
-			return i;
-		i++;
-	}
-
-	return -EINVAL;
-}
-
-static int exynos4_bus_setvolt(struct busfreq_data *data,
-			       struct busfreq_opp_info *oppi,
-			       struct busfreq_opp_info *oldoppi)
-{
-	int err = 0, tmp;
-	unsigned long volt = oppi->volt;
-
-	switch (data->type) {
-	case TYPE_BUSF_EXYNOS4210:
-		/* OPP represents DMC clock + INT voltage */
-		err = regulator_set_voltage(data->vdd_int, volt,
-					    MAX_SAFEVOLT);
-		break;
-	case TYPE_BUSF_EXYNOS4x12:
-		/* OPP represents MIF clock + MIF voltage */
-		err = regulator_set_voltage(data->vdd_mif, volt,
-					    MAX_SAFEVOLT);
-		if (err)
-			break;
-
-		tmp = exynos4x12_get_intspec(oppi->rate);
-		if (tmp < 0) {
-			err = tmp;
-			regulator_set_voltage(data->vdd_mif,
-					      oldoppi->volt,
-					      MAX_SAFEVOLT);
-			break;
-		}
-		err = regulator_set_voltage(data->vdd_int,
-					    exynos4x12_intclk_table[tmp].volt,
-					    MAX_SAFEVOLT);
-		/*  Try to recover */
-		if (err)
-			regulator_set_voltage(data->vdd_mif,
-					      oldoppi->volt,
-					      MAX_SAFEVOLT);
-		break;
-	default:
-		err = -EINVAL;
-	}
-
-	return err;
-}
-
-static int exynos4_bus_target(struct device *dev, unsigned long *_freq,
-			      u32 flags)
-{
-	int err = 0;
-	struct platform_device *pdev = container_of(dev, struct platform_device,
-						    dev);
-	struct busfreq_data *data = platform_get_drvdata(pdev);
-	struct dev_pm_opp *opp;
-	unsigned long freq;
-	unsigned long old_freq = data->curr_oppinfo.rate;
-	struct busfreq_opp_info	new_oppinfo;
-
-	rcu_read_lock();
-	opp = devfreq_recommended_opp(dev, _freq, flags);
-	if (IS_ERR(opp)) {
-		rcu_read_unlock();
-		return PTR_ERR(opp);
-	}
-	new_oppinfo.rate = dev_pm_opp_get_freq(opp);
-	new_oppinfo.volt = dev_pm_opp_get_voltage(opp);
-	rcu_read_unlock();
-	freq = new_oppinfo.rate;
-
-	if (old_freq == freq)
-		return 0;
-
-	dev_dbg(dev, "targeting %lukHz %luuV\n", freq, new_oppinfo.volt);
-
-	mutex_lock(&data->lock);
-
-	if (data->disabled)
-		goto out;
-
-	if (old_freq < freq)
-		err = exynos4_bus_setvolt(data, &new_oppinfo,
-					  &data->curr_oppinfo);
-	if (err)
-		goto out;
-
-	if (old_freq != freq) {
-		switch (data->type) {
-		case TYPE_BUSF_EXYNOS4210:
-			err = exynos4210_set_busclk(data, &new_oppinfo);
-			break;
-		case TYPE_BUSF_EXYNOS4x12:
-			err = exynos4x12_set_busclk(data, &new_oppinfo);
-			break;
-		default:
-			err = -EINVAL;
-		}
-	}
-	if (err)
-		goto out;
-
-	if (old_freq > freq)
-		err = exynos4_bus_setvolt(data, &new_oppinfo,
-					  &data->curr_oppinfo);
-	if (err)
-		goto out;
-
-	data->curr_oppinfo = new_oppinfo;
-out:
-	mutex_unlock(&data->lock);
-	return err;
-}
-
-static int exynos4_bus_get_dev_status(struct device *dev,
-				      struct devfreq_dev_status *stat)
-{
-	struct busfreq_data *data = dev_get_drvdata(dev);
-	struct busfreq_ppmu_data *ppmu_data = &data->ppmu_data;
-	int busier;
-
-	exynos_read_ppmu(ppmu_data);
-	busier = exynos_get_busier_ppmu(ppmu_data);
-	stat->current_frequency = data->curr_oppinfo.rate;
-
-	/* Number of cycles spent on memory access */
-	stat->busy_time = ppmu_data->ppmu[busier].count[PPMU_PMNCNT3];
-	stat->busy_time *= 100 / BUS_SATURATION_RATIO;
-	stat->total_time = ppmu_data->ppmu[busier].ccnt;
-
-	/* If the counters have overflown, retry */
-	if (ppmu_data->ppmu[busier].ccnt_overflow ||
-	    ppmu_data->ppmu[busier].count_overflow[0])
-		return -EAGAIN;
-
-	return 0;
-}
-
-static struct devfreq_dev_profile exynos4_devfreq_profile = {
-	.initial_freq	= 400000,
-	.polling_ms	= 50,
-	.target		= exynos4_bus_target,
-	.get_dev_status	= exynos4_bus_get_dev_status,
-};
-
-static int exynos4210_init_tables(struct busfreq_data *data)
-{
-	u32 tmp;
-	int mgrp;
-	int i, err = 0;
-
-	tmp = __raw_readl(EXYNOS4_CLKDIV_DMC0);
-	for (i = LV_0; i < EX4210_LV_NUM; i++) {
-		tmp &= ~(EXYNOS4_CLKDIV_DMC0_ACP_MASK |
-			EXYNOS4_CLKDIV_DMC0_ACPPCLK_MASK |
-			EXYNOS4_CLKDIV_DMC0_DPHY_MASK |
-			EXYNOS4_CLKDIV_DMC0_DMC_MASK |
-			EXYNOS4_CLKDIV_DMC0_DMCD_MASK |
-			EXYNOS4_CLKDIV_DMC0_DMCP_MASK |
-			EXYNOS4_CLKDIV_DMC0_COPY2_MASK |
-			EXYNOS4_CLKDIV_DMC0_CORETI_MASK);
-
-		tmp |= ((exynos4210_clkdiv_dmc0[i][0] <<
-					EXYNOS4_CLKDIV_DMC0_ACP_SHIFT) |
-			(exynos4210_clkdiv_dmc0[i][1] <<
-					EXYNOS4_CLKDIV_DMC0_ACPPCLK_SHIFT) |
-			(exynos4210_clkdiv_dmc0[i][2] <<
-					EXYNOS4_CLKDIV_DMC0_DPHY_SHIFT) |
-			(exynos4210_clkdiv_dmc0[i][3] <<
-					EXYNOS4_CLKDIV_DMC0_DMC_SHIFT) |
-			(exynos4210_clkdiv_dmc0[i][4] <<
-					EXYNOS4_CLKDIV_DMC0_DMCD_SHIFT) |
-			(exynos4210_clkdiv_dmc0[i][5] <<
-					EXYNOS4_CLKDIV_DMC0_DMCP_SHIFT) |
-			(exynos4210_clkdiv_dmc0[i][6] <<
-					EXYNOS4_CLKDIV_DMC0_COPY2_SHIFT) |
-			(exynos4210_clkdiv_dmc0[i][7] <<
-					EXYNOS4_CLKDIV_DMC0_CORETI_SHIFT));
-
-		data->dmc_divtable[i] = tmp;
-	}
-
-	tmp = __raw_readl(EXYNOS4_CLKDIV_TOP);
-	for (i = LV_0; i <  EX4210_LV_NUM; i++) {
-		tmp &= ~(EXYNOS4_CLKDIV_TOP_ACLK200_MASK |
-			EXYNOS4_CLKDIV_TOP_ACLK100_MASK |
-			EXYNOS4_CLKDIV_TOP_ACLK160_MASK |
-			EXYNOS4_CLKDIV_TOP_ACLK133_MASK |
-			EXYNOS4_CLKDIV_TOP_ONENAND_MASK);
-
-		tmp |= ((exynos4210_clkdiv_top[i][0] <<
-					EXYNOS4_CLKDIV_TOP_ACLK200_SHIFT) |
-			(exynos4210_clkdiv_top[i][1] <<
-					EXYNOS4_CLKDIV_TOP_ACLK100_SHIFT) |
-			(exynos4210_clkdiv_top[i][2] <<
-					EXYNOS4_CLKDIV_TOP_ACLK160_SHIFT) |
-			(exynos4210_clkdiv_top[i][3] <<
-					EXYNOS4_CLKDIV_TOP_ACLK133_SHIFT) |
-			(exynos4210_clkdiv_top[i][4] <<
-					EXYNOS4_CLKDIV_TOP_ONENAND_SHIFT));
-
-		data->top_divtable[i] = tmp;
-	}
-
-	/*
-	 * TODO: init tmp based on busfreq_data
-	 * (device-tree or platform-data)
-	 */
-	tmp = 0; /* Max voltages for the reliability of the unknown */
-
-	pr_debug("ASV Group of Exynos4 is %d\n", tmp);
-	/* Use merged grouping for voltage */
-	switch (tmp) {
-	case 0:
-		mgrp = 0;
-		break;
-	case 1:
-	case 2:
-		mgrp = 1;
-		break;
-	case 3:
-	case 4:
-		mgrp = 2;
-		break;
-	case 5:
-	case 6:
-		mgrp = 3;
-		break;
-	case 7:
-		mgrp = 4;
-		break;
-	default:
-		pr_warn("Unknown ASV Group. Use max voltage.\n");
-		mgrp = 0;
-	}
-
-	for (i = LV_0; i < EX4210_LV_NUM; i++)
-		exynos4210_busclk_table[i].volt = exynos4210_asv_volt[mgrp][i];
-
-	for (i = LV_0; i < EX4210_LV_NUM; i++) {
-		err = dev_pm_opp_add(data->dev, exynos4210_busclk_table[i].clk,
-			      exynos4210_busclk_table[i].volt);
-		if (err) {
-			dev_err(data->dev, "Cannot add opp entries.\n");
-			return err;
-		}
-	}
-
-
-	return 0;
-}
-
-static int exynos4x12_init_tables(struct busfreq_data *data)
-{
-	unsigned int i;
-	unsigned int tmp;
-	int ret;
-
-	/* Enable pause function for DREX2 DVFS */
-	tmp = __raw_readl(EXYNOS4_DMC_PAUSE_CTRL);
-	tmp |= EXYNOS4_DMC_PAUSE_ENABLE;
-	__raw_writel(tmp, EXYNOS4_DMC_PAUSE_CTRL);
-
-	tmp = __raw_readl(EXYNOS4_CLKDIV_DMC0);
-
-	for (i = 0; i <  EX4x12_LV_NUM; i++) {
-		tmp &= ~(EXYNOS4_CLKDIV_DMC0_ACP_MASK |
-			EXYNOS4_CLKDIV_DMC0_ACPPCLK_MASK |
-			EXYNOS4_CLKDIV_DMC0_DPHY_MASK |
-			EXYNOS4_CLKDIV_DMC0_DMC_MASK |
-			EXYNOS4_CLKDIV_DMC0_DMCD_MASK |
-			EXYNOS4_CLKDIV_DMC0_DMCP_MASK);
-
-		tmp |= ((exynos4x12_clkdiv_dmc0[i][0] <<
-					EXYNOS4_CLKDIV_DMC0_ACP_SHIFT) |
-			(exynos4x12_clkdiv_dmc0[i][1] <<
-					EXYNOS4_CLKDIV_DMC0_ACPPCLK_SHIFT) |
-			(exynos4x12_clkdiv_dmc0[i][2] <<
-					EXYNOS4_CLKDIV_DMC0_DPHY_SHIFT) |
-			(exynos4x12_clkdiv_dmc0[i][3] <<
-					EXYNOS4_CLKDIV_DMC0_DMC_SHIFT) |
-			(exynos4x12_clkdiv_dmc0[i][4] <<
-					EXYNOS4_CLKDIV_DMC0_DMCD_SHIFT) |
-			(exynos4x12_clkdiv_dmc0[i][5] <<
-					EXYNOS4_CLKDIV_DMC0_DMCP_SHIFT));
-
-		data->dmc_divtable[i] = tmp;
-	}
-
-	tmp = 0; /* Max voltages for the reliability of the unknown */
-
-	if (tmp > 8)
-		tmp = 0;
-	pr_debug("ASV Group of Exynos4x12 is %d\n", tmp);
-
-	for (i = 0; i < EX4x12_LV_NUM; i++) {
-		exynos4x12_mifclk_table[i].volt =
-			exynos4x12_mif_step_50[tmp][i];
-		exynos4x12_intclk_table[i].volt =
-			exynos4x12_int_volt[tmp][i];
-	}
-
-	for (i = 0; i < EX4x12_LV_NUM; i++) {
-		ret = dev_pm_opp_add(data->dev, exynos4x12_mifclk_table[i].clk,
-			      exynos4x12_mifclk_table[i].volt);
-		if (ret) {
-			dev_err(data->dev, "Fail to add opp entries.\n");
-			return ret;
-		}
-	}
-
-	return 0;
-}
-
-static int exynos4_busfreq_pm_notifier_event(struct notifier_block *this,
-		unsigned long event, void *ptr)
-{
-	struct busfreq_data *data = container_of(this, struct busfreq_data,
-						 pm_notifier);
-	struct dev_pm_opp *opp;
-	struct busfreq_opp_info	new_oppinfo;
-	unsigned long maxfreq = ULONG_MAX;
-	int err = 0;
-
-	switch (event) {
-	case PM_SUSPEND_PREPARE:
-		/* Set Fastest and Deactivate DVFS */
-		mutex_lock(&data->lock);
-
-		data->disabled = true;
-
-		rcu_read_lock();
-		opp = dev_pm_opp_find_freq_floor(data->dev, &maxfreq);
-		if (IS_ERR(opp)) {
-			rcu_read_unlock();
-			dev_err(data->dev, "%s: unable to find a min freq\n",
-				__func__);
-			mutex_unlock(&data->lock);
-			return PTR_ERR(opp);
-		}
-		new_oppinfo.rate = dev_pm_opp_get_freq(opp);
-		new_oppinfo.volt = dev_pm_opp_get_voltage(opp);
-		rcu_read_unlock();
-
-		err = exynos4_bus_setvolt(data, &new_oppinfo,
-					  &data->curr_oppinfo);
-		if (err)
-			goto unlock;
-
-		switch (data->type) {
-		case TYPE_BUSF_EXYNOS4210:
-			err = exynos4210_set_busclk(data, &new_oppinfo);
-			break;
-		case TYPE_BUSF_EXYNOS4x12:
-			err = exynos4x12_set_busclk(data, &new_oppinfo);
-			break;
-		default:
-			err = -EINVAL;
-		}
-		if (err)
-			goto unlock;
-
-		data->curr_oppinfo = new_oppinfo;
-unlock:
-		mutex_unlock(&data->lock);
-		if (err)
-			return err;
-		return NOTIFY_OK;
-	case PM_POST_RESTORE:
-	case PM_POST_SUSPEND:
-		/* Reactivate */
-		mutex_lock(&data->lock);
-		data->disabled = false;
-		mutex_unlock(&data->lock);
-		return NOTIFY_OK;
-	}
-
-	return NOTIFY_DONE;
-}
-
-static int exynos4_busfreq_probe(struct platform_device *pdev)
-{
-	struct busfreq_data *data;
-	struct busfreq_ppmu_data *ppmu_data;
-	struct dev_pm_opp *opp;
-	struct device *dev = &pdev->dev;
-	int err = 0;
-
-	data = devm_kzalloc(&pdev->dev, sizeof(struct busfreq_data), GFP_KERNEL);
-	if (data == NULL) {
-		dev_err(dev, "Cannot allocate memory.\n");
-		return -ENOMEM;
-	}
-
-	ppmu_data = &data->ppmu_data;
-	ppmu_data->ppmu_end = PPMU_END;
-	ppmu_data->ppmu = devm_kzalloc(dev,
-				       sizeof(struct exynos_ppmu) * PPMU_END,
-				       GFP_KERNEL);
-	if (!ppmu_data->ppmu) {
-		dev_err(dev, "Failed to allocate memory for exynos_ppmu\n");
-		return -ENOMEM;
-	}
-
-	data->type = pdev->id_entry->driver_data;
-	ppmu_data->ppmu[PPMU_DMC0].hw_base = S5P_VA_DMC0;
-	ppmu_data->ppmu[PPMU_DMC1].hw_base = S5P_VA_DMC1;
-	data->pm_notifier.notifier_call = exynos4_busfreq_pm_notifier_event;
-	data->dev = dev;
-	mutex_init(&data->lock);
-
-	switch (data->type) {
-	case TYPE_BUSF_EXYNOS4210:
-		err = exynos4210_init_tables(data);
-		break;
-	case TYPE_BUSF_EXYNOS4x12:
-		err = exynos4x12_init_tables(data);
-		break;
-	default:
-		dev_err(dev, "Cannot determine the device id %d\n", data->type);
-		err = -EINVAL;
-	}
-	if (err) {
-		dev_err(dev, "Cannot initialize busfreq table %d\n",
-			     data->type);
-		return err;
-	}
-
-	data->vdd_int = devm_regulator_get(dev, "vdd_int");
-	if (IS_ERR(data->vdd_int)) {
-		dev_err(dev, "Cannot get the regulator \"vdd_int\"\n");
-		return PTR_ERR(data->vdd_int);
-	}
-	if (data->type == TYPE_BUSF_EXYNOS4x12) {
-		data->vdd_mif = devm_regulator_get(dev, "vdd_mif");
-		if (IS_ERR(data->vdd_mif)) {
-			dev_err(dev, "Cannot get the regulator \"vdd_mif\"\n");
-			return PTR_ERR(data->vdd_mif);
-		}
-	}
-
-	rcu_read_lock();
-	opp = dev_pm_opp_find_freq_floor(dev,
-					 &exynos4_devfreq_profile.initial_freq);
-	if (IS_ERR(opp)) {
-		rcu_read_unlock();
-		dev_err(dev, "Invalid initial frequency %lu kHz.\n",
-			exynos4_devfreq_profile.initial_freq);
-		return PTR_ERR(opp);
-	}
-	data->curr_oppinfo.rate = dev_pm_opp_get_freq(opp);
-	data->curr_oppinfo.volt = dev_pm_opp_get_voltage(opp);
-	rcu_read_unlock();
-
-	platform_set_drvdata(pdev, data);
-
-	data->devfreq = devm_devfreq_add_device(dev, &exynos4_devfreq_profile,
-					   "simple_ondemand", NULL);
-	if (IS_ERR(data->devfreq))
-		return PTR_ERR(data->devfreq);
-
-	/*
-	 * Start PPMU (Performance Profiling Monitoring Unit) to check
-	 * utilization of each IP in the Exynos4 SoC.
-	 */
-	busfreq_mon_reset(ppmu_data);
-
-	/* Register opp_notifier for Exynos4 busfreq */
-	err = devm_devfreq_register_opp_notifier(dev, data->devfreq);
-	if (err < 0) {
-		dev_err(dev, "Failed to register opp notifier\n");
-		return err;
-	}
-
-	/* Register pm_notifier for Exynos4 busfreq */
-	err = register_pm_notifier(&data->pm_notifier);
-	if (err) {
-		dev_err(dev, "Failed to setup pm notifier\n");
-		return err;
-	}
-
-	return 0;
-}
-
-static int exynos4_busfreq_remove(struct platform_device *pdev)
-{
-	struct busfreq_data *data = platform_get_drvdata(pdev);
-
-	/* Unregister all of notifier chain */
-	unregister_pm_notifier(&data->pm_notifier);
-
-	return 0;
-}
-
-#ifdef CONFIG_PM_SLEEP
-static int exynos4_busfreq_resume(struct device *dev)
-{
-	struct busfreq_data *data = dev_get_drvdata(dev);
-	struct busfreq_ppmu_data *ppmu_data = &data->ppmu_data;
-
-	busfreq_mon_reset(ppmu_data);
-	return 0;
-}
-#endif
-
-static SIMPLE_DEV_PM_OPS(exynos4_busfreq_pm_ops, NULL, exynos4_busfreq_resume);
-
-static const struct platform_device_id exynos4_busfreq_id[] = {
-	{ "exynos4210-busfreq", TYPE_BUSF_EXYNOS4210 },
-	{ "exynos4412-busfreq", TYPE_BUSF_EXYNOS4x12 },
-	{ "exynos4212-busfreq", TYPE_BUSF_EXYNOS4x12 },
-	{ },
-};
-
-static struct platform_driver exynos4_busfreq_driver = {
-	.probe	= exynos4_busfreq_probe,
-	.remove	= exynos4_busfreq_remove,
-	.id_table = exynos4_busfreq_id,
-	.driver = {
-		.name	= "exynos4-busfreq",
-		.pm	= &exynos4_busfreq_pm_ops,
-	},
-};
-
-static int __init exynos4_busfreq_init(void)
-{
-	return platform_driver_register(&exynos4_busfreq_driver);
-}
-late_initcall(exynos4_busfreq_init);
-
-static void __exit exynos4_busfreq_exit(void)
-{
-	platform_driver_unregister(&exynos4_busfreq_driver);
-}
-module_exit(exynos4_busfreq_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("EXYNOS4 busfreq driver with devfreq framework");
-MODULE_AUTHOR("MyungJoo Ham <myungjoo.ham@samsung.com>");
diff --git a/drivers/devfreq/exynos/exynos4_bus.h b/drivers/devfreq/exynos/exynos4_bus.h
deleted file mode 100644
index 94c73c18d28c..000000000000
--- a/drivers/devfreq/exynos/exynos4_bus.h
+++ /dev/null
@@ -1,110 +0,0 @@
-/*
- * Copyright (c) 2013 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *
- * EXYNOS4 BUS header
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __DEVFREQ_EXYNOS4_BUS_H
-#define __DEVFREQ_EXYNOS4_BUS_H __FILE__
-
-#include <mach/map.h>
-
-#define EXYNOS4_CLKDIV_LEFTBUS			(S5P_VA_CMU + 0x04500)
-#define EXYNOS4_CLKDIV_STAT_LEFTBUS		(S5P_VA_CMU + 0x04600)
-
-#define EXYNOS4_CLKDIV_RIGHTBUS			(S5P_VA_CMU + 0x08500)
-#define EXYNOS4_CLKDIV_STAT_RIGHTBUS		(S5P_VA_CMU + 0x08600)
-
-#define EXYNOS4_CLKDIV_TOP			(S5P_VA_CMU + 0x0C510)
-#define EXYNOS4_CLKDIV_CAM			(S5P_VA_CMU + 0x0C520)
-#define EXYNOS4_CLKDIV_MFC			(S5P_VA_CMU + 0x0C528)
-
-#define EXYNOS4_CLKDIV_STAT_TOP			(S5P_VA_CMU + 0x0C610)
-#define EXYNOS4_CLKDIV_STAT_MFC			(S5P_VA_CMU + 0x0C628)
-
-#define EXYNOS4210_CLKGATE_IP_IMAGE		(S5P_VA_CMU + 0x0C930)
-#define EXYNOS4212_CLKGATE_IP_IMAGE		(S5P_VA_CMU + 0x04930)
-
-#define EXYNOS4_CLKDIV_DMC0			(S5P_VA_CMU + 0x10500)
-#define EXYNOS4_CLKDIV_DMC1			(S5P_VA_CMU + 0x10504)
-#define EXYNOS4_CLKDIV_STAT_DMC0		(S5P_VA_CMU + 0x10600)
-#define EXYNOS4_CLKDIV_STAT_DMC1		(S5P_VA_CMU + 0x10604)
-
-#define EXYNOS4_DMC_PAUSE_CTRL			(S5P_VA_CMU + 0x11094)
-#define EXYNOS4_DMC_PAUSE_ENABLE		(1 << 0)
-
-#define EXYNOS4_CLKDIV_DMC0_ACP_SHIFT		(0)
-#define EXYNOS4_CLKDIV_DMC0_ACP_MASK		(0x7 << EXYNOS4_CLKDIV_DMC0_ACP_SHIFT)
-#define EXYNOS4_CLKDIV_DMC0_ACPPCLK_SHIFT	(4)
-#define EXYNOS4_CLKDIV_DMC0_ACPPCLK_MASK	(0x7 << EXYNOS4_CLKDIV_DMC0_ACPPCLK_SHIFT)
-#define EXYNOS4_CLKDIV_DMC0_DPHY_SHIFT		(8)
-#define EXYNOS4_CLKDIV_DMC0_DPHY_MASK		(0x7 << EXYNOS4_CLKDIV_DMC0_DPHY_SHIFT)
-#define EXYNOS4_CLKDIV_DMC0_DMC_SHIFT		(12)
-#define EXYNOS4_CLKDIV_DMC0_DMC_MASK		(0x7 << EXYNOS4_CLKDIV_DMC0_DMC_SHIFT)
-#define EXYNOS4_CLKDIV_DMC0_DMCD_SHIFT		(16)
-#define EXYNOS4_CLKDIV_DMC0_DMCD_MASK		(0x7 << EXYNOS4_CLKDIV_DMC0_DMCD_SHIFT)
-#define EXYNOS4_CLKDIV_DMC0_DMCP_SHIFT		(20)
-#define EXYNOS4_CLKDIV_DMC0_DMCP_MASK		(0x7 << EXYNOS4_CLKDIV_DMC0_DMCP_SHIFT)
-#define EXYNOS4_CLKDIV_DMC0_COPY2_SHIFT		(24)
-#define EXYNOS4_CLKDIV_DMC0_COPY2_MASK		(0x7 << EXYNOS4_CLKDIV_DMC0_COPY2_SHIFT)
-#define EXYNOS4_CLKDIV_DMC0_CORETI_SHIFT	(28)
-#define EXYNOS4_CLKDIV_DMC0_CORETI_MASK		(0x7 << EXYNOS4_CLKDIV_DMC0_CORETI_SHIFT)
-
-#define EXYNOS4_CLKDIV_DMC1_G2D_ACP_SHIFT	(0)
-#define EXYNOS4_CLKDIV_DMC1_G2D_ACP_MASK	(0xf << EXYNOS4_CLKDIV_DMC1_G2D_ACP_SHIFT)
-#define EXYNOS4_CLKDIV_DMC1_C2C_SHIFT		(4)
-#define EXYNOS4_CLKDIV_DMC1_C2C_MASK		(0x7 << EXYNOS4_CLKDIV_DMC1_C2C_SHIFT)
-#define EXYNOS4_CLKDIV_DMC1_PWI_SHIFT		(8)
-#define EXYNOS4_CLKDIV_DMC1_PWI_MASK		(0xf << EXYNOS4_CLKDIV_DMC1_PWI_SHIFT)
-#define EXYNOS4_CLKDIV_DMC1_C2CACLK_SHIFT	(12)
-#define EXYNOS4_CLKDIV_DMC1_C2CACLK_MASK	(0x7 << EXYNOS4_CLKDIV_DMC1_C2CACLK_SHIFT)
-#define EXYNOS4_CLKDIV_DMC1_DVSEM_SHIFT		(16)
-#define EXYNOS4_CLKDIV_DMC1_DVSEM_MASK		(0x7f << EXYNOS4_CLKDIV_DMC1_DVSEM_SHIFT)
-#define EXYNOS4_CLKDIV_DMC1_DPM_SHIFT		(24)
-#define EXYNOS4_CLKDIV_DMC1_DPM_MASK		(0x7f << EXYNOS4_CLKDIV_DMC1_DPM_SHIFT)
-
-#define EXYNOS4_CLKDIV_MFC_SHIFT		(0)
-#define EXYNOS4_CLKDIV_MFC_MASK			(0x7 << EXYNOS4_CLKDIV_MFC_SHIFT)
-
-#define EXYNOS4_CLKDIV_TOP_ACLK200_SHIFT	(0)
-#define EXYNOS4_CLKDIV_TOP_ACLK200_MASK		(0x7 << EXYNOS4_CLKDIV_TOP_ACLK200_SHIFT)
-#define EXYNOS4_CLKDIV_TOP_ACLK100_SHIFT	(4)
-#define EXYNOS4_CLKDIV_TOP_ACLK100_MASK		(0xF << EXYNOS4_CLKDIV_TOP_ACLK100_SHIFT)
-#define EXYNOS4_CLKDIV_TOP_ACLK160_SHIFT	(8)
-#define EXYNOS4_CLKDIV_TOP_ACLK160_MASK		(0x7 << EXYNOS4_CLKDIV_TOP_ACLK160_SHIFT)
-#define EXYNOS4_CLKDIV_TOP_ACLK133_SHIFT	(12)
-#define EXYNOS4_CLKDIV_TOP_ACLK133_MASK		(0x7 << EXYNOS4_CLKDIV_TOP_ACLK133_SHIFT)
-#define EXYNOS4_CLKDIV_TOP_ONENAND_SHIFT	(16)
-#define EXYNOS4_CLKDIV_TOP_ONENAND_MASK		(0x7 << EXYNOS4_CLKDIV_TOP_ONENAND_SHIFT)
-#define EXYNOS4_CLKDIV_TOP_ACLK266_GPS_SHIFT	(20)
-#define EXYNOS4_CLKDIV_TOP_ACLK266_GPS_MASK	(0x7 << EXYNOS4_CLKDIV_TOP_ACLK266_GPS_SHIFT)
-#define EXYNOS4_CLKDIV_TOP_ACLK400_MCUISP_SHIFT	(24)
-#define EXYNOS4_CLKDIV_TOP_ACLK400_MCUISP_MASK	(0x7 << EXYNOS4_CLKDIV_TOP_ACLK400_MCUISP_SHIFT)
-
-#define EXYNOS4_CLKDIV_BUS_GDLR_SHIFT		(0)
-#define EXYNOS4_CLKDIV_BUS_GDLR_MASK		(0x7 << EXYNOS4_CLKDIV_BUS_GDLR_SHIFT)
-#define EXYNOS4_CLKDIV_BUS_GPLR_SHIFT		(4)
-#define EXYNOS4_CLKDIV_BUS_GPLR_MASK		(0x7 << EXYNOS4_CLKDIV_BUS_GPLR_SHIFT)
-
-#define EXYNOS4_CLKDIV_CAM_FIMC0_SHIFT		(0)
-#define EXYNOS4_CLKDIV_CAM_FIMC0_MASK		(0xf << EXYNOS4_CLKDIV_CAM_FIMC0_SHIFT)
-#define EXYNOS4_CLKDIV_CAM_FIMC1_SHIFT		(4)
-#define EXYNOS4_CLKDIV_CAM_FIMC1_MASK		(0xf << EXYNOS4_CLKDIV_CAM_FIMC1_SHIFT)
-#define EXYNOS4_CLKDIV_CAM_FIMC2_SHIFT		(8)
-#define EXYNOS4_CLKDIV_CAM_FIMC2_MASK		(0xf << EXYNOS4_CLKDIV_CAM_FIMC2_SHIFT)
-#define EXYNOS4_CLKDIV_CAM_FIMC3_SHIFT		(12)
-#define EXYNOS4_CLKDIV_CAM_FIMC3_MASK		(0xf << EXYNOS4_CLKDIV_CAM_FIMC3_SHIFT)
-
-#define EXYNOS4_CLKDIV_CAM1			(S5P_VA_CMU + 0x0C568)
-
-#define EXYNOS4_CLKDIV_STAT_CAM1		(S5P_VA_CMU + 0x0C668)
-
-#define EXYNOS4_CLKDIV_CAM1_JPEG_SHIFT		(0)
-#define EXYNOS4_CLKDIV_CAM1_JPEG_MASK		(0xf << EXYNOS4_CLKDIV_CAM1_JPEG_SHIFT)
-
-#endif /* __DEVFREQ_EXYNOS4_BUS_H */
diff --git a/drivers/devfreq/exynos/exynos5_bus.c b/drivers/devfreq/exynos/exynos5_bus.c
deleted file mode 100644
index 297ea30d4159..000000000000
--- a/drivers/devfreq/exynos/exynos5_bus.c
+++ /dev/null
@@ -1,431 +0,0 @@
-/*
- * Copyright (c) 2012 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *
- * EXYNOS5 INT clock frequency scaling support using DEVFREQ framework
- * Based on work done by Jonghwan Choi <jhbird.choi@samsung.com>
- * Support for only EXYNOS5250 is present.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/module.h>
-#include <linux/devfreq.h>
-#include <linux/io.h>
-#include <linux/pm_opp.h>
-#include <linux/slab.h>
-#include <linux/suspend.h>
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/pm_qos.h>
-#include <linux/regulator/consumer.h>
-#include <linux/of_address.h>
-#include <linux/of_platform.h>
-
-#include "exynos_ppmu.h"
-
-#define MAX_SAFEVOLT			1100000 /* 1.10V */
-/* Assume that the bus is saturated if the utilization is 25% */
-#define INT_BUS_SATURATION_RATIO	25
-
-enum int_level_idx {
-	LV_0,
-	LV_1,
-	LV_2,
-	LV_3,
-	LV_4,
-	_LV_END
-};
-
-enum exynos_ppmu_list {
-	PPMU_RIGHT,
-	PPMU_END,
-};
-
-struct busfreq_data_int {
-	struct device *dev;
-	struct devfreq *devfreq;
-	struct regulator *vdd_int;
-	struct busfreq_ppmu_data ppmu_data;
-	unsigned long curr_freq;
-	bool disabled;
-
-	struct notifier_block pm_notifier;
-	struct mutex lock;
-	struct pm_qos_request int_req;
-	struct clk *int_clk;
-};
-
-struct int_bus_opp_table {
-	unsigned int idx;
-	unsigned long clk;
-	unsigned long volt;
-};
-
-static struct int_bus_opp_table exynos5_int_opp_table[] = {
-	{LV_0, 266000, 1025000},
-	{LV_1, 200000, 1025000},
-	{LV_2, 160000, 1025000},
-	{LV_3, 133000, 1025000},
-	{LV_4, 100000, 1025000},
-	{0, 0, 0},
-};
-
-static int exynos5_int_setvolt(struct busfreq_data_int *data,
-				unsigned long volt)
-{
-	return regulator_set_voltage(data->vdd_int, volt, MAX_SAFEVOLT);
-}
-
-static int exynos5_busfreq_int_target(struct device *dev, unsigned long *_freq,
-			      u32 flags)
-{
-	int err = 0;
-	struct platform_device *pdev = container_of(dev, struct platform_device,
-						    dev);
-	struct busfreq_data_int *data = platform_get_drvdata(pdev);
-	struct dev_pm_opp *opp;
-	unsigned long old_freq, freq;
-	unsigned long volt;
-
-	rcu_read_lock();
-	opp = devfreq_recommended_opp(dev, _freq, flags);
-	if (IS_ERR(opp)) {
-		rcu_read_unlock();
-		dev_err(dev, "%s: Invalid OPP.\n", __func__);
-		return PTR_ERR(opp);
-	}
-
-	freq = dev_pm_opp_get_freq(opp);
-	volt = dev_pm_opp_get_voltage(opp);
-	rcu_read_unlock();
-
-	old_freq = data->curr_freq;
-
-	if (old_freq == freq)
-		return 0;
-
-	dev_dbg(dev, "targeting %lukHz %luuV\n", freq, volt);
-
-	mutex_lock(&data->lock);
-
-	if (data->disabled)
-		goto out;
-
-	if (freq > exynos5_int_opp_table[0].clk)
-		pm_qos_update_request(&data->int_req, freq * 16 / 1000);
-	else
-		pm_qos_update_request(&data->int_req, -1);
-
-	if (old_freq < freq)
-		err = exynos5_int_setvolt(data, volt);
-	if (err)
-		goto out;
-
-	err = clk_set_rate(data->int_clk, freq * 1000);
-
-	if (err)
-		goto out;
-
-	if (old_freq > freq)
-		err = exynos5_int_setvolt(data, volt);
-	if (err)
-		goto out;
-
-	data->curr_freq = freq;
-out:
-	mutex_unlock(&data->lock);
-	return err;
-}
-
-static int exynos5_int_get_dev_status(struct device *dev,
-				      struct devfreq_dev_status *stat)
-{
-	struct platform_device *pdev = container_of(dev, struct platform_device,
-						    dev);
-	struct busfreq_data_int *data = platform_get_drvdata(pdev);
-	struct busfreq_ppmu_data *ppmu_data = &data->ppmu_data;
-	int busier_dmc;
-
-	exynos_read_ppmu(ppmu_data);
-	busier_dmc = exynos_get_busier_ppmu(ppmu_data);
-
-	stat->current_frequency = data->curr_freq;
-
-	/* Number of cycles spent on memory access */
-	stat->busy_time = ppmu_data->ppmu[busier_dmc].count[PPMU_PMNCNT3];
-	stat->busy_time *= 100 / INT_BUS_SATURATION_RATIO;
-	stat->total_time = ppmu_data->ppmu[busier_dmc].ccnt;
-
-	return 0;
-}
-
-static struct devfreq_dev_profile exynos5_devfreq_int_profile = {
-	.initial_freq		= 160000,
-	.polling_ms		= 100,
-	.target			= exynos5_busfreq_int_target,
-	.get_dev_status		= exynos5_int_get_dev_status,
-};
-
-static int exynos5250_init_int_tables(struct busfreq_data_int *data)
-{
-	int i, err = 0;
-
-	for (i = LV_0; i < _LV_END; i++) {
-		err = dev_pm_opp_add(data->dev, exynos5_int_opp_table[i].clk,
-				exynos5_int_opp_table[i].volt);
-		if (err) {
-			dev_err(data->dev, "Cannot add opp entries.\n");
-			return err;
-		}
-	}
-
-	return 0;
-}
-
-static int exynos5_busfreq_int_pm_notifier_event(struct notifier_block *this,
-		unsigned long event, void *ptr)
-{
-	struct busfreq_data_int *data = container_of(this,
-					struct busfreq_data_int, pm_notifier);
-	struct dev_pm_opp *opp;
-	unsigned long maxfreq = ULONG_MAX;
-	unsigned long freq;
-	unsigned long volt;
-	int err = 0;
-
-	switch (event) {
-	case PM_SUSPEND_PREPARE:
-		/* Set Fastest and Deactivate DVFS */
-		mutex_lock(&data->lock);
-
-		data->disabled = true;
-
-		rcu_read_lock();
-		opp = dev_pm_opp_find_freq_floor(data->dev, &maxfreq);
-		if (IS_ERR(opp)) {
-			rcu_read_unlock();
-			err = PTR_ERR(opp);
-			goto unlock;
-		}
-		freq = dev_pm_opp_get_freq(opp);
-		volt = dev_pm_opp_get_voltage(opp);
-		rcu_read_unlock();
-
-		err = exynos5_int_setvolt(data, volt);
-		if (err)
-			goto unlock;
-
-		err = clk_set_rate(data->int_clk, freq * 1000);
-
-		if (err)
-			goto unlock;
-
-		data->curr_freq = freq;
-unlock:
-		mutex_unlock(&data->lock);
-		if (err)
-			return NOTIFY_BAD;
-		return NOTIFY_OK;
-	case PM_POST_RESTORE:
-	case PM_POST_SUSPEND:
-		/* Reactivate */
-		mutex_lock(&data->lock);
-		data->disabled = false;
-		mutex_unlock(&data->lock);
-		return NOTIFY_OK;
-	}
-
-	return NOTIFY_DONE;
-}
-
-static int exynos5_busfreq_int_probe(struct platform_device *pdev)
-{
-	struct busfreq_data_int *data;
-	struct busfreq_ppmu_data *ppmu_data;
-	struct dev_pm_opp *opp;
-	struct device *dev = &pdev->dev;
-	struct device_node *np;
-	unsigned long initial_freq;
-	unsigned long initial_volt;
-	int err = 0;
-	int i;
-
-	data = devm_kzalloc(&pdev->dev, sizeof(struct busfreq_data_int),
-				GFP_KERNEL);
-	if (data == NULL) {
-		dev_err(dev, "Cannot allocate memory.\n");
-		return -ENOMEM;
-	}
-
-	ppmu_data = &data->ppmu_data;
-	ppmu_data->ppmu_end = PPMU_END;
-	ppmu_data->ppmu = devm_kzalloc(dev,
-				       sizeof(struct exynos_ppmu) * PPMU_END,
-				       GFP_KERNEL);
-	if (!ppmu_data->ppmu) {
-		dev_err(dev, "Failed to allocate memory for exynos_ppmu\n");
-		return -ENOMEM;
-	}
-
-	np = of_find_compatible_node(NULL, NULL, "samsung,exynos5250-ppmu");
-	if (np == NULL) {
-		pr_err("Unable to find PPMU node\n");
-		return -ENOENT;
-	}
-
-	for (i = 0; i < ppmu_data->ppmu_end; i++) {
-		/* map PPMU memory region */
-		ppmu_data->ppmu[i].hw_base = of_iomap(np, i);
-		if (ppmu_data->ppmu[i].hw_base == NULL) {
-			dev_err(&pdev->dev, "failed to map memory region\n");
-			return -ENOMEM;
-		}
-	}
-	data->pm_notifier.notifier_call = exynos5_busfreq_int_pm_notifier_event;
-	data->dev = dev;
-	mutex_init(&data->lock);
-
-	err = exynos5250_init_int_tables(data);
-	if (err)
-		return err;
-
-	data->vdd_int = devm_regulator_get(dev, "vdd_int");
-	if (IS_ERR(data->vdd_int)) {
-		dev_err(dev, "Cannot get the regulator \"vdd_int\"\n");
-		return PTR_ERR(data->vdd_int);
-	}
-
-	data->int_clk = devm_clk_get(dev, "int_clk");
-	if (IS_ERR(data->int_clk)) {
-		dev_err(dev, "Cannot get clock \"int_clk\"\n");
-		return PTR_ERR(data->int_clk);
-	}
-
-	rcu_read_lock();
-	opp = dev_pm_opp_find_freq_floor(dev,
-			&exynos5_devfreq_int_profile.initial_freq);
-	if (IS_ERR(opp)) {
-		rcu_read_unlock();
-		dev_err(dev, "Invalid initial frequency %lu kHz.\n",
-		       exynos5_devfreq_int_profile.initial_freq);
-		return PTR_ERR(opp);
-	}
-	initial_freq = dev_pm_opp_get_freq(opp);
-	initial_volt = dev_pm_opp_get_voltage(opp);
-	rcu_read_unlock();
-	data->curr_freq = initial_freq;
-
-	err = clk_set_rate(data->int_clk, initial_freq * 1000);
-	if (err) {
-		dev_err(dev, "Failed to set initial frequency\n");
-		return err;
-	}
-
-	err = exynos5_int_setvolt(data, initial_volt);
-	if (err)
-		return err;
-
-	platform_set_drvdata(pdev, data);
-
-	busfreq_mon_reset(ppmu_data);
-
-	data->devfreq = devm_devfreq_add_device(dev, &exynos5_devfreq_int_profile,
-					   "simple_ondemand", NULL);
-	if (IS_ERR(data->devfreq))
-		return PTR_ERR(data->devfreq);
-
-	err = devm_devfreq_register_opp_notifier(dev, data->devfreq);
-	if (err < 0) {
-		dev_err(dev, "Failed to register opp notifier\n");
-		return err;
-	}
-
-	err = register_pm_notifier(&data->pm_notifier);
-	if (err) {
-		dev_err(dev, "Failed to setup pm notifier\n");
-		return err;
-	}
-
-	/* TODO: Add a new QOS class for int/mif bus */
-	pm_qos_add_request(&data->int_req, PM_QOS_NETWORK_THROUGHPUT, -1);
-
-	return 0;
-}
-
-static int exynos5_busfreq_int_remove(struct platform_device *pdev)
-{
-	struct busfreq_data_int *data = platform_get_drvdata(pdev);
-
-	pm_qos_remove_request(&data->int_req);
-	unregister_pm_notifier(&data->pm_notifier);
-
-	return 0;
-}
-
-#ifdef CONFIG_PM_SLEEP
-static int exynos5_busfreq_int_resume(struct device *dev)
-{
-	struct platform_device *pdev = container_of(dev, struct platform_device,
-						    dev);
-	struct busfreq_data_int *data = platform_get_drvdata(pdev);
-	struct busfreq_ppmu_data *ppmu_data = &data->ppmu_data;
-
-	busfreq_mon_reset(ppmu_data);
-	return 0;
-}
-static const struct dev_pm_ops exynos5_busfreq_int_pm = {
-	.resume	= exynos5_busfreq_int_resume,
-};
-#endif
-static SIMPLE_DEV_PM_OPS(exynos5_busfreq_int_pm_ops, NULL,
-			 exynos5_busfreq_int_resume);
-
-/* platform device pointer for exynos5 devfreq device. */
-static struct platform_device *exynos5_devfreq_pdev;
-
-static struct platform_driver exynos5_busfreq_int_driver = {
-	.probe		= exynos5_busfreq_int_probe,
-	.remove		= exynos5_busfreq_int_remove,
-	.driver		= {
-		.name		= "exynos5-bus-int",
-		.pm		= &exynos5_busfreq_int_pm_ops,
-	},
-};
-
-static int __init exynos5_busfreq_int_init(void)
-{
-	int ret;
-
-	ret = platform_driver_register(&exynos5_busfreq_int_driver);
-	if (ret < 0)
-		goto out;
-
-	exynos5_devfreq_pdev =
-		platform_device_register_simple("exynos5-bus-int", -1, NULL, 0);
-	if (IS_ERR(exynos5_devfreq_pdev)) {
-		ret = PTR_ERR(exynos5_devfreq_pdev);
-		goto out1;
-	}
-
-	return 0;
-out1:
-	platform_driver_unregister(&exynos5_busfreq_int_driver);
-out:
-	return ret;
-}
-late_initcall(exynos5_busfreq_int_init);
-
-static void __exit exynos5_busfreq_int_exit(void)
-{
-	platform_device_unregister(exynos5_devfreq_pdev);
-	platform_driver_unregister(&exynos5_busfreq_int_driver);
-}
-module_exit(exynos5_busfreq_int_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("EXYNOS5 busfreq driver with devfreq framework");
diff --git a/drivers/devfreq/exynos/exynos_ppmu.c b/drivers/devfreq/exynos/exynos_ppmu.c
deleted file mode 100644
index 97b75e513d29..000000000000
--- a/drivers/devfreq/exynos/exynos_ppmu.c
+++ /dev/null
@@ -1,119 +0,0 @@
-/*
- * Copyright (c) 2012 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *
- * EXYNOS - PPMU support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/io.h>
-
-#include "exynos_ppmu.h"
-
-void exynos_ppmu_reset(void __iomem *ppmu_base)
-{
-	__raw_writel(PPMU_CYCLE_RESET | PPMU_COUNTER_RESET, ppmu_base);
-	__raw_writel(PPMU_ENABLE_CYCLE  |
-		     PPMU_ENABLE_COUNT0 |
-		     PPMU_ENABLE_COUNT1 |
-		     PPMU_ENABLE_COUNT2 |
-		     PPMU_ENABLE_COUNT3,
-		     ppmu_base + PPMU_CNTENS);
-}
-
-void exynos_ppmu_setevent(void __iomem *ppmu_base, unsigned int ch,
-			unsigned int evt)
-{
-	__raw_writel(evt, ppmu_base + PPMU_BEVTSEL(ch));
-}
-
-void exynos_ppmu_start(void __iomem *ppmu_base)
-{
-	__raw_writel(PPMU_ENABLE, ppmu_base);
-}
-
-void exynos_ppmu_stop(void __iomem *ppmu_base)
-{
-	__raw_writel(PPMU_DISABLE, ppmu_base);
-}
-
-unsigned int exynos_ppmu_read(void __iomem *ppmu_base, unsigned int ch)
-{
-	unsigned int total;
-
-	if (ch == PPMU_PMNCNT3)
-		total = ((__raw_readl(ppmu_base + PMCNT_OFFSET(ch)) << 8) |
-			  __raw_readl(ppmu_base + PMCNT_OFFSET(ch + 1)));
-	else
-		total = __raw_readl(ppmu_base + PMCNT_OFFSET(ch));
-
-	return total;
-}
-
-void busfreq_mon_reset(struct busfreq_ppmu_data *ppmu_data)
-{
-	unsigned int i;
-
-	for (i = 0; i < ppmu_data->ppmu_end; i++) {
-		void __iomem *ppmu_base = ppmu_data->ppmu[i].hw_base;
-
-		/* Reset the performance and cycle counters */
-		exynos_ppmu_reset(ppmu_base);
-
-		/* Setup count registers to monitor read/write transactions */
-		ppmu_data->ppmu[i].event[PPMU_PMNCNT3] = RDWR_DATA_COUNT;
-		exynos_ppmu_setevent(ppmu_base, PPMU_PMNCNT3,
-					ppmu_data->ppmu[i].event[PPMU_PMNCNT3]);
-
-		exynos_ppmu_start(ppmu_base);
-	}
-}
-EXPORT_SYMBOL(busfreq_mon_reset);
-
-void exynos_read_ppmu(struct busfreq_ppmu_data *ppmu_data)
-{
-	int i, j;
-
-	for (i = 0; i < ppmu_data->ppmu_end; i++) {
-		void __iomem *ppmu_base = ppmu_data->ppmu[i].hw_base;
-
-		exynos_ppmu_stop(ppmu_base);
-
-		/* Update local data from PPMU */
-		ppmu_data->ppmu[i].ccnt = __raw_readl(ppmu_base + PPMU_CCNT);
-
-		for (j = PPMU_PMNCNT0; j < PPMU_PMNCNT_MAX; j++) {
-			if (ppmu_data->ppmu[i].event[j] == 0)
-				ppmu_data->ppmu[i].count[j] = 0;
-			else
-				ppmu_data->ppmu[i].count[j] =
-					exynos_ppmu_read(ppmu_base, j);
-		}
-	}
-
-	busfreq_mon_reset(ppmu_data);
-}
-EXPORT_SYMBOL(exynos_read_ppmu);
-
-int exynos_get_busier_ppmu(struct busfreq_ppmu_data *ppmu_data)
-{
-	unsigned int count = 0;
-	int i, j, busy = 0;
-
-	for (i = 0; i < ppmu_data->ppmu_end; i++) {
-		for (j = PPMU_PMNCNT0; j < PPMU_PMNCNT_MAX; j++) {
-			if (ppmu_data->ppmu[i].count[j] > count) {
-				count = ppmu_data->ppmu[i].count[j];
-				busy = i;
-			}
-		}
-	}
-
-	return busy;
-}
-EXPORT_SYMBOL(exynos_get_busier_ppmu);
diff --git a/drivers/devfreq/exynos/exynos_ppmu.h b/drivers/devfreq/exynos/exynos_ppmu.h
deleted file mode 100644
index 71f17ba3563c..000000000000
--- a/drivers/devfreq/exynos/exynos_ppmu.h
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * Copyright (c) 2012 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *
- * EXYNOS PPMU header
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __DEVFREQ_EXYNOS_PPMU_H
-#define __DEVFREQ_EXYNOS_PPMU_H __FILE__
-
-#include <linux/ktime.h>
-
-/* For PPMU Control */
-#define PPMU_ENABLE             BIT(0)
-#define PPMU_DISABLE            0x0
-#define PPMU_CYCLE_RESET        BIT(1)
-#define PPMU_COUNTER_RESET      BIT(2)
-
-#define PPMU_ENABLE_COUNT0      BIT(0)
-#define PPMU_ENABLE_COUNT1      BIT(1)
-#define PPMU_ENABLE_COUNT2      BIT(2)
-#define PPMU_ENABLE_COUNT3      BIT(3)
-#define PPMU_ENABLE_CYCLE       BIT(31)
-
-#define PPMU_CNTENS		0x10
-#define PPMU_FLAG		0x50
-#define PPMU_CCNT_OVERFLOW	BIT(31)
-#define PPMU_CCNT		0x100
-
-#define PPMU_PMCNT0		0x110
-#define PPMU_PMCNT_OFFSET	0x10
-#define PMCNT_OFFSET(x)		(PPMU_PMCNT0 + (PPMU_PMCNT_OFFSET * x))
-
-#define PPMU_BEVT0SEL		0x1000
-#define PPMU_BEVTSEL_OFFSET	0x100
-#define PPMU_BEVTSEL(x)		(PPMU_BEVT0SEL + (ch * PPMU_BEVTSEL_OFFSET))
-
-/* For Event Selection */
-#define RD_DATA_COUNT		0x5
-#define WR_DATA_COUNT		0x6
-#define RDWR_DATA_COUNT		0x7
-
-enum ppmu_counter {
-	PPMU_PMNCNT0,
-	PPMU_PMCCNT1,
-	PPMU_PMNCNT2,
-	PPMU_PMNCNT3,
-	PPMU_PMNCNT_MAX,
-};
-
-struct bus_opp_table {
-	unsigned int idx;
-	unsigned long clk;
-	unsigned long volt;
-};
-
-struct exynos_ppmu {
-	void __iomem *hw_base;
-	unsigned int ccnt;
-	unsigned int event[PPMU_PMNCNT_MAX];
-	unsigned int count[PPMU_PMNCNT_MAX];
-	unsigned long long ns;
-	ktime_t reset_time;
-	bool ccnt_overflow;
-	bool count_overflow[PPMU_PMNCNT_MAX];
-};
-
-struct busfreq_ppmu_data {
-	struct exynos_ppmu *ppmu;
-	int ppmu_end;
-};
-
-void exynos_ppmu_reset(void __iomem *ppmu_base);
-void exynos_ppmu_setevent(void __iomem *ppmu_base, unsigned int ch,
-			unsigned int evt);
-void exynos_ppmu_start(void __iomem *ppmu_base);
-void exynos_ppmu_stop(void __iomem *ppmu_base);
-unsigned int exynos_ppmu_read(void __iomem *ppmu_base, unsigned int ch);
-void busfreq_mon_reset(struct busfreq_ppmu_data *ppmu_data);
-void exynos_read_ppmu(struct busfreq_ppmu_data *ppmu_data);
-int exynos_get_busier_ppmu(struct busfreq_ppmu_data *ppmu_data);
-#endif /* __DEVFREQ_EXYNOS_PPMU_H */
-- 
1.9.1

[RFC PATCH 11/15] ARM: dts: Add bus nodes using VDD_INT for Exynos3250

[Chanwoo Choi]

This patch adds the bus nodes using VDD_INT for Exynos3250 SoC.
Exynos3250 has following AXI buses to translate data between
DRAM and sub-blocks.

Following list specifies the detailed relation between DRAM and sub-blocks:
- ACLK400 clock for MCUISP
- ACLK266 clock for ISP
- ACLK200 clock for FSYS
- ACLK160 clock for LCD0
- ACLK100 clock for PERIL
- GDL clock for LEFTBUS
- GDR clock for RIGHTBUS

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 arch/arm/boot/dts/exynos3250.dtsi | 152 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 152 insertions(+)

diff --git a/arch/arm/boot/dts/exynos3250.dtsi b/arch/arm/boot/dts/exynos3250.dtsi
index 45809f83c628..2e5d60c24004 100644
--- a/arch/arm/boot/dts/exynos3250.dtsi
+++ b/arch/arm/boot/dts/exynos3250.dtsi
@@ -734,6 +734,158 @@
 				opp-microvolt = <875000>;
 			};
 		};
+
+		bus_leftbus: bus_leftbus {
+			compatible = "samsung,exynos-bus";
+			clocks = <&cmu CLK_DIV_GDL>;
+			clock-names = "bus";
+			operating-points-v2 = <&bus_leftbus_opp_table>;
+			status = "disabled";
+		};
+
+		bus_rightbus: bus_rightbus {
+			compatible = "samsung,exynos-bus";
+			clocks = <&cmu CLK_DIV_GDR>;
+			clock-names = "bus";
+			operating-points-v2 = <&bus_leftbus_opp_table>;
+			status = "disabled";
+		};
+
+		bus_lcd0: bus_lcd0 {
+			compatible = "samsung,exynos-bus";
+			clocks = <&cmu CLK_DIV_ACLK_160>;
+			clock-names = "bus";
+			operating-points-v2 = <&bus_leftbus_opp_table>;
+			status = "disabled";
+		};
+
+		bus_fsys: bus_fsys {
+			compatible = "samsung,exynos-bus";
+			clocks = <&cmu CLK_DIV_ACLK_200>;
+			clock-names = "bus";
+			operating-points-v2 = <&bus_leftbus_opp_table>;
+			status = "disabled";
+		};
+
+		bus_mcuisp: bus_mcuisp {
+			compatible = "samsung,exynos-bus";
+			clocks = <&cmu CLK_DIV_ACLK_400_MCUISP>;
+			clock-names = "bus";
+			operating-points-v2 = <&bus_mcuisp_opp_table>;
+			status = "disabled";
+		};
+
+		bus_isp: bus_isp {
+			compatible = "samsung,exynos-bus";
+			clocks = <&cmu CLK_DIV_ACLK_266>;
+			clock-names = "bus";
+			operating-points-v2 = <&bus_isp_opp_table>;
+			status = "disabled";
+		};
+
+		bus_peril: bus_peril {
+			compatible = "samsung,exynos-bus";
+			clocks = <&cmu CLK_DIV_ACLK_100>;
+			clock-names = "bus";
+			operating-points-v2 = <&bus_peril_opp_table>;
+			status = "disabled";
+		};
+
+		bus_leftbus_opp_table: opp_table1 {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp00 {
+				opp-hz = /bits/ 64 <50000000>;
+				opp-microvolt = <900000>;
+			};
+			opp01 {
+				opp-hz = /bits/ 64 <80000000>;
+				opp-microvolt = <900000>;
+			};
+			opp02 {
+				opp-hz = /bits/ 64 <100000000>;
+				opp-microvolt = <1000000>;
+			};
+			opp03 {
+				opp-hz = /bits/ 64 <133000000>;
+				opp-microvolt = <1000000>;
+			};
+			opp04 {
+				opp-hz = /bits/ 64 <200000000>;
+				opp-microvolt = <1000000>;
+			};
+		};
+
+		bus_mcuisp_opp_table: opp_table2 {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp00 {
+				opp-hz = /bits/ 64 <50000000>;
+				opp-microvolt = <900000>;
+			};
+			opp01 {
+				opp-hz = /bits/ 64 <80000000>;
+				opp-microvolt = <900000>;
+			};
+			opp02 {
+				opp-hz = /bits/ 64 <100000000>;
+				opp-microvolt = <1000000>;
+			};
+			opp03 {
+				opp-hz = /bits/ 64 <200000000>;
+				opp-microvolt = <1000000>;
+			};
+			opp04 {
+				opp-hz = /bits/ 64 <400000000>;
+				opp-microvolt = <1000000>;
+			};
+		};
+
+		bus_isp_opp_table: opp_table3 {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp00 {
+				opp-hz = /bits/ 64 <50000000>;
+				opp-microvolt = <900000>;
+			};
+			opp01 {
+				opp-hz = /bits/ 64 <80000000>;
+				opp-microvolt = <900000>;
+			};
+			opp02 {
+				opp-hz = /bits/ 64 <100000000>;
+				opp-microvolt = <1000000>;
+			};
+			opp03 {
+				opp-hz = /bits/ 64 <200000000>;
+				opp-microvolt = <1000000>;
+			};
+			opp04 {
+				opp-hz = /bits/ 64 <300000000>;
+				opp-microvolt = <1000000>;
+			};
+		};
+
+		bus_peril_opp_table: opp_table4 {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp00 {
+				opp-hz = /bits/ 64 <50000000>;
+				opp-microvolt = <900000>;
+			};
+			opp01 {
+				opp-hz = /bits/ 64 <80000000>;
+				opp-microvolt = <900000>;
+			};
+			opp02 {
+				opp-hz = /bits/ 64 <100000000>;
+				opp-microvolt = <1000000>;
+			};
+		};
 	};
 };
 
-- 
1.9.1

[RFC PATCH 12/15] ARM: dts: Add support of bus frequency using VDD_INT for exynos3250-rinato

[Chanwoo Choi]

This patch adds the bus device-tree node of INT (internal) block
to enable the bus frequency. The following sub-blocks share
the VDD_INT power source:
- LEFTBUS (parent device)
- RIGHTBUS
- PERIL
- LCD0
- FSYS
- MCUISP / ISP

The LEFTBUS is parent device with devfreq ondemand governor
and the rest devices has the dependency on LEFTBUS bus.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 arch/arm/boot/dts/exynos3250-rinato.dts | 36 +++++++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index 61477943015b..9fc90d83968c 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -681,6 +681,42 @@
 	status = "okay";
 };
 
+&bus_leftbus {
+	devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
+	vdd-supply = <&buck3_reg>;
+	status = "okay";
+};
+
+&bus_rightbus {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_lcd0 {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_fsys {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_mcuisp {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_isp {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_peril {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
 &xusbxti {
 	clock-frequency = <24000000>;
 };
-- 
1.9.1

[RFC PATCH 13/15] ARM: dts: Add bus nodes using VDD_MIF for Exynos4x12

[Chanwoo Choi]

This patch adds the bus noes using VDD_MIF for Exynos4x12 SoC.
Exynos4x12 has the following AXI buses to translate data
between DRAM and DMC/ACP/C2C.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 arch/arm/boot/dts/exynos4x12.dtsi | 73 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 73 insertions(+)

diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
index b77dac61ffb5..c7ab2825d7cd 100644
--- a/arch/arm/boot/dts/exynos4x12.dtsi
+++ b/arch/arm/boot/dts/exynos4x12.dtsi
@@ -282,6 +282,79 @@
 		clocks = <&clock CLK_SMMU_LITE1>, <&clock CLK_FIMC_LITE1>;
 		#iommu-cells = <0>;
 	};
+
+	bus_dmc: bus_dmc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_DMC>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_dmc_opp_table>;
+		status = "disabled";
+	};
+
+	bus_acp: bus_acp {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_ACP>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_acp_opp_table>;
+		status = "disabled";
+	};
+
+	bus_c2c: bus_c2c {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_C2C>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_dmc_opp_table>;
+		status = "disabled";
+	};
+
+	bus_dmc_opp_table: opp_table0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <950000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <133000000>;
+			opp-microvolt = <950000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <160000000>;
+			opp-microvolt = <950000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <1100000>;
+		};
+	};
+
+	bus_acp_opp_table: opp_table1 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <950000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <133000000>;
+			opp-microvolt = <950000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <160000000>;
+			opp-microvolt = <950000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <1000000>;
+		};
+	};
+
 };
 
 &combiner {
-- 
1.9.1

[RFC PATCH 14/15] ARM: dts: Add bus nodes using VDD_INT for Exynos4x12

[Chanwoo Choi]

This patch adds the bus noes using VDD_INT for Exynos4x12 SoC.
Exynos4x12 has the following AXI buses to translate data between
DRAM and sub-blocks.

Following list specifies the detailed relation between DRAM and sub-blocks:
- ACLK100 clock for PERIL/PERIR/MFC(PCLK)
- ACLK160 clock for CAM/TV/LCD
- ACLK133 clock for FSYS
- GDL clock for LEFTBUS
- GDR clock for RIGHTBUS
- SCLK_MFC clock for MFC

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 arch/arm/boot/dts/exynos4x12.dtsi | 119 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 119 insertions(+)

diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
index c7ab2825d7cd..1b90d4984e35 100644
--- a/arch/arm/boot/dts/exynos4x12.dtsi
+++ b/arch/arm/boot/dts/exynos4x12.dtsi
@@ -355,6 +355,125 @@
 		};
 	};
 
+	bus_leftbus: bus_leftbus {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_GDL>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_rightbus: bus_leftbus {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_DIV_GDR>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_display: bus_display {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_ACLK160>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_display_opp_table>;
+		status = "disabled";
+	};
+
+	bus_fsys: bus_fsys {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_ACLK133>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_fsys_opp_table>;
+		status = "disabled";
+	};
+
+	bus_peri: bus_peri {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_ACLK100>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_peri_opp_table>;
+		status = "disabled";
+	};
+
+	bus_mfc: bus_mfc {
+		compatible = "samsung,exynos-bus";
+		clocks = <&clock CLK_SCLK_MFC>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_leftbus_opp_table>;
+		status = "disabled";
+	};
+
+	bus_leftbus_opp_table: opp_table1 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <133000000>;
+			opp-microvolt = <925000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <160000000>;
+			opp-microvolt = <950000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <1000000>;
+		};
+	};
+
+	bus_display_opp_table: opp_table2 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <133000000>;
+			opp-microvolt = <925000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <160000000>;
+			opp-microvolt = <950000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <160000000>;
+			opp-microvolt = <1000000>;
+		};
+	};
+
+	bus_fsys_opp_table: opp_table3 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <133000000>;
+			opp-microvolt = <925000>;
+		};
+	};
+
+	bus_peri_opp_table: opp_table4 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <50000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <925000>;
+		};
+	};
 };
 
 &combiner {
-- 
1.9.1

[RFC PATCH 15/15] ARM: dts: Add support of bus frequency for exynos4412-trats

[Chanwoo Choi]

THis patch adds the bus device tree nodes for both MIF (Memory) and INT
(Internal) block to enable the bus frequency.

The DMC bus is parent device in MIF block using VDD_MIF and the LEFTBUS
bus is parent device in INT block using VDD_INT.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 arch/arm/boot/dts/exynos4412-trats2.dts | 47 +++++++++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
index 40a474c4374b..aecd545803ad 100644
--- a/arch/arm/boot/dts/exynos4412-trats2.dts
+++ b/arch/arm/boot/dts/exynos4412-trats2.dts
@@ -1286,3 +1286,50 @@
 	vtmu-supply = <&ldo10_reg>;
 	status = "okay";
 };
+
+&bus_dmc {
+	devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
+	vdd-supply = <&buck1_reg>;
+	status = "okay";
+};
+
+&bus_acp {
+	devfreq = <&bus_dmc>;
+	status = "okay";
+};
+
+&bus_c2c {
+	devfreq = <&bus_dmc>;
+	status = "okay";
+};
+
+&bus_leftbus {
+	devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
+	vdd-supply = <&buck3_reg>;
+	status = "okay";
+};
+
+&bus_rightbus {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_display {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_fsys {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_peri {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_mfc {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
-- 
1.9.1

Re: [RFC PATCH 01/15] PM / devfreq: exynos: Add generic exynos bus frequency driver

[MyungJoo Ham]

On Thu, Nov 26, 2015 at 10:47 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
> This patch adds the generic exynos bus frequency driver for AMBA AXI bus
> of sub-blocks in exynos SoC with DEVFREQ framework. The Samsung Exynos SoC
> have the common architecture for bus between DRAM and sub-blocks in SoC.
> This driver can support the generic bus frequency driver for Exynos SoCs.
>
> In devicetree, Each bus block has a bus clock, regulator, operation-point
> and devfreq-event devices which measure the utilization of each bus block.
>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> ---
>  drivers/devfreq/Kconfig             |  15 ++
>  drivers/devfreq/Makefile            |   1 +
>  drivers/devfreq/exynos/Makefile     |   1 +
>  drivers/devfreq/exynos/exynos-bus.c | 443 ++++++++++++++++++++++++++++++++++++
>  4 files changed, 460 insertions(+)
>  create mode 100644 drivers/devfreq/exynos/exynos-bus.c
>

Are we finally getting a common Exynos bus driver with full DT support?
(can this replace both Exynos4/5 drivers and support Exynos7 series?)


Cheers,
MyungJoo

Re: [RFC PATCH 01/15] PM / devfreq: exynos: Add generic exynos bus frequency driver

[Chanwoo Choi]

On Thu, Nov 26, 2015 at 11:00 PM, MyungJoo Ham <myungjoo.ham@samsung.com> wrote:
> On Thu, Nov 26, 2015 at 10:47 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>> This patch adds the generic exynos bus frequency driver for AMBA AXI bus
>> of sub-blocks in exynos SoC with DEVFREQ framework. The Samsung Exynos SoC
>> have the common architecture for bus between DRAM and sub-blocks in SoC.
>> This driver can support the generic bus frequency driver for Exynos SoCs.
>>
>> In devicetree, Each bus block has a bus clock, regulator, operation-point
>> and devfreq-event devices which measure the utilization of each bus block.
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>> ---
>>  drivers/devfreq/Kconfig             |  15 ++
>>  drivers/devfreq/Makefile            |   1 +
>>  drivers/devfreq/exynos/Makefile     |   1 +
>>  drivers/devfreq/exynos/exynos-bus.c | 443 ++++++++++++++++++++++++++++++++++++
>>  4 files changed, 460 insertions(+)
>>  create mode 100644 drivers/devfreq/exynos/exynos-bus.c
>>
>
> Are we finally getting a common Exynos bus driver with full DT support?
> (can this replace both Exynos4/5 drivers and support Exynos7 series?)

Yes.
This patch-set would support all Exynos SoCs for bus frequency driver.
To make sure the support for Exynos7 series, I need to check the TRM
document of Exynos7.  I think it is possible for support Exynos7.

I'm going to test this driver on various Exynos-based board.

Regards,
Chanwoo Choi

Re: [RFC PATCH 01/15] PM / devfreq: exynos: Add generic exynos bus frequency driver

[Anand Moon]

Hi Chanwoo,

On 26 November 2015 at 21:42, Chanwoo Choi <cwchoi00@gmail.com> wrote:
> On Thu, Nov 26, 2015 at 11:00 PM, MyungJoo Ham <myungjoo.ham@samsung.com> wrote:
>> On Thu, Nov 26, 2015 at 10:47 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>>> This patch adds the generic exynos bus frequency driver for AMBA AXI bus
>>> of sub-blocks in exynos SoC with DEVFREQ framework. The Samsung Exynos SoC
>>> have the common architecture for bus between DRAM and sub-blocks in SoC.
>>> This driver can support the generic bus frequency driver for Exynos SoCs.
>>>
>>> In devicetree, Each bus block has a bus clock, regulator, operation-point
>>> and devfreq-event devices which measure the utilization of each bus block.
>>>
>>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>>> ---
>>>  drivers/devfreq/Kconfig             |  15 ++
>>>  drivers/devfreq/Makefile            |   1 +
>>>  drivers/devfreq/exynos/Makefile     |   1 +
>>>  drivers/devfreq/exynos/exynos-bus.c | 443 ++++++++++++++++++++++++++++++++++++
>>>  4 files changed, 460 insertions(+)
>>>  create mode 100644 drivers/devfreq/exynos/exynos-bus.c
>>>
>>
>> Are we finally getting a common Exynos bus driver with full DT support?
>> (can this replace both Exynos4/5 drivers and support Exynos7 series?)
>
> Yes.
> This patch-set would support all Exynos SoCs for bus frequency driver.
> To make sure the support for Exynos7 series, I need to check the TRM
> document of Exynos7.  I think it is possible for support Exynos7.
>
> I'm going to test this driver on various Exynos-based board.
>
> Regards,
> Chanwoo Choi

Please do consider Exynos 542x series as well.

-Anand Moon
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [RFC PATCH 01/15] PM / devfreq: exynos: Add generic exynos bus frequency driver

[Chanwoo Choi]

Hi Anand,

On 2015년 11월 27일 02:17, Anand Moon wrote:
> Hi Chanwoo,
> 
> On 26 November 2015 at 21:42, Chanwoo Choi <cwchoi00@gmail.com> wrote:
>> On Thu, Nov 26, 2015 at 11:00 PM, MyungJoo Ham <myungjoo.ham@samsung.com> wrote:
>>> On Thu, Nov 26, 2015 at 10:47 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>>>> This patch adds the generic exynos bus frequency driver for AMBA AXI bus
>>>> of sub-blocks in exynos SoC with DEVFREQ framework. The Samsung Exynos SoC
>>>> have the common architecture for bus between DRAM and sub-blocks in SoC.
>>>> This driver can support the generic bus frequency driver for Exynos SoCs.
>>>>
>>>> In devicetree, Each bus block has a bus clock, regulator, operation-point
>>>> and devfreq-event devices which measure the utilization of each bus block.
>>>>
>>>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>>>> ---
>>>>  drivers/devfreq/Kconfig             |  15 ++
>>>>  drivers/devfreq/Makefile            |   1 +
>>>>  drivers/devfreq/exynos/Makefile     |   1 +
>>>>  drivers/devfreq/exynos/exynos-bus.c | 443 ++++++++++++++++++++++++++++++++++++
>>>>  4 files changed, 460 insertions(+)
>>>>  create mode 100644 drivers/devfreq/exynos/exynos-bus.c
>>>>
>>>
>>> Are we finally getting a common Exynos bus driver with full DT support?
>>> (can this replace both Exynos4/5 drivers and support Exynos7 series?)
>>
>> Yes.
>> This patch-set would support all Exynos SoCs for bus frequency driver.
>> To make sure the support for Exynos7 series, I need to check the TRM
>> document of Exynos7.  I think it is possible for support Exynos7.
>>
>> I'm going to test this driver on various Exynos-based board.
>>
>> Regards,
>> Chanwoo Choi
> 
> Please do consider Exynos 542x series as well.

Sure. I'll to test it on Exynos5422-based Odroid-XU3.

Regards,
Chanwoo Choi

Re: [RFC PATCH 02/15] PM / devfreq: exynos: Add documentation for generic exynos bus frequency driver

[Rob Herring]

On Thu, Nov 26, 2015 at 10:47:26PM +0900, Chanwoo Choi wrote:
> This patch adds the documentation for generic exynos bus frequency
> driver.
> 
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> ---
>  .../devicetree/bindings/devfreq/exynos-bus.txt     | 92 ++++++++++++++++++++++
>  1 file changed, 92 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/devfreq/exynos-bus.txt
> 
> diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
> new file mode 100644
> index 000000000000..5d90623bd173
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
> @@ -0,0 +1,92 @@
> +* Generic Exynos Bus frequency device
> +
> +The Samsung Exynos SoC have many buses for data transfer between DRAM
> +and sub-blocks in SoC. Almost Exynos SoC have the common architecture
> +for buses. Generally, the each bus of Exynos SoC includes the source clock
> +and power line and then is able to change the clock according to the usage
> +of each buses on runtime. When gathering the usage of each buses on runtime,
> +thie driver uses the exynos-ppmu.c driver with DEVFREQ-EVENT framework.

Please don't refer to Linux subsystem specifics in bindings. It looks 
like you are creating devices to match what you have for drivers, not 
what the h/w looks like.


> +There are a little different composition among Exynos SoC because each Exynos
> +SoC has the different sub-blocks. So, this difference should be specified
> +in devicetree file instead of each device driver. In result, this driver
> +is able to support the bus frequency for all Exynos SoCs.
> +
> +Required properties for bus device:
> +- compatible: Should be "samsung,exynos-bus".
> +- clock-names : the name of clock used by the bus, "bus".
> +- clocks : phandles for clock specified in "clock-names" property.
> +- #clock-cells: should be 1.
> +- operating-points-v2: the OPP table including frequency/voltage information
> +  to support DVFS (Dynamic Voltage/Frequency Scaling) feature.
> +- vdd-supply: the regulator to provide the buses with the voltage.
> +- devfreq-events: the devfreq-event device to monitor the curret utilization
> +  of buses.
> +
> +Optional properties for bus device:
> +- exynos,saturation-ratio: the percentage value which is used to calibrate
> +                   the performance count againt total cycle count.
> +
> +Example1:
> +	Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to
> +	power line (regulator). The MIF (Memory Interface) AXI bus is used to
> +	transfer data between DRAM and CPU and uses the VDD_MIF regualtor.
> +
> +	- power line(VDD_MIF) --> bus for DMC block (dmc clock)
> +
> +	- MIF bus's frequency/voltage table
> +	-----------------------
> +	|Lv| Freq   | Voltage |
> +	-----------------------
> +	|L1| 50000  |800000   |
> +	|L2| 100000 |800000   |
> +	|L3| 133000 |800000   |
> +	|L4| 200000 |800000   |
> +	|L5| 400000 |875000   |
> +	-----------------------
> +
> +Example2 :
> +	The bus of DMC block in exynos3250.dtsi are listed below:

What is DMC?

> +
> +	bus_dmc: bus_dmc {
> +		compatible = "samsung,exynos-bus";

I would expect the children of this bus to be under this node.

> +		clocks = <&cmu_dmc CLK_DIV_DMC>;
> +		clock-names = "bus";
> +		operating-points-v2 = <&bus_dmc_opp_table>;
> +		status = "disabled";
> +	};
> +
> +	bus_dmc_opp_table: opp_table0 {
> +		compatible = "operating-points-v2";
> +		opp-shared;
> +
> +		opp00 {
> +			opp-hz = /bits/ 64 <50000000>;
> +			opp-microvolt = <800000>;
> +		};
> +		opp01 {
> +			opp-hz = /bits/ 64 <100000000>;
> +			opp-microvolt = <800000>;
> +		};
> +		opp02 {
> +			opp-hz = /bits/ 64 <133000000>;
> +			opp-microvolt = <800000>;
> +		};
> +		opp03 {
> +			opp-hz = /bits/ 64 <200000000>;
> +			opp-microvolt = <800000>;
> +		};
> +		opp04 {
> +			opp-hz = /bits/ 64 <400000000>;
> +			opp-microvolt = <875000>;
> +		};
> +	};
> +
> +	Usage case to handle the frequency and voltage of bus on runtime
> +	in exynos3250-rinato.dts are listed below:
> +
> +	&bus_dmc {
> +		devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;

What do these phandles point to exactly?

> +		vdd-supply = <&buck1_reg>;	/* VDD_MIF */
> +		status = "okay";
> +	};
> -- 
> 1.9.1
> 

Re: [RFC PATCH 02/15] PM / devfreq: exynos: Add documentation for generic exynos bus frequency driver

[Chanwoo Choi]

Hi Rob,

On Sat, Nov 28, 2015 at 5:30 AM, Rob Herring <robh@kernel.org> wrote:
> On Thu, Nov 26, 2015 at 10:47:26PM +0900, Chanwoo Choi wrote:
>> This patch adds the documentation for generic exynos bus frequency
>> driver.
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>> ---
>>  .../devicetree/bindings/devfreq/exynos-bus.txt     | 92 ++++++++++++++++++++++
>>  1 file changed, 92 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/devfreq/exynos-bus.txt
>>
>> diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
>> new file mode 100644
>> index 000000000000..5d90623bd173
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
>> @@ -0,0 +1,92 @@
>> +* Generic Exynos Bus frequency device
>> +
>> +The Samsung Exynos SoC have many buses for data transfer between DRAM
>> +and sub-blocks in SoC. Almost Exynos SoC have the common architecture
>> +for buses. Generally, the each bus of Exynos SoC includes the source clock
>> +and power line and then is able to change the clock according to the usage
>> +of each buses on runtime. When gathering the usage of each buses on runtime,
>> +thie driver uses the exynos-ppmu.c driver with DEVFREQ-EVENT framework.
>
> Please don't refer to Linux subsystem specifics in bindings. It looks
> like you are creating devices to match what you have for drivers, not
> what the h/w looks like.

OK. I'll modify it on next patchiest.

>
>
>> +There are a little different composition among Exynos SoC because each Exynos
>> +SoC has the different sub-blocks. So, this difference should be specified
>> +in devicetree file instead of each device driver. In result, this driver
>> +is able to support the bus frequency for all Exynos SoCs.
>> +
>> +Required properties for bus device:
>> +- compatible: Should be "samsung,exynos-bus".
>> +- clock-names : the name of clock used by the bus, "bus".
>> +- clocks : phandles for clock specified in "clock-names" property.
>> +- #clock-cells: should be 1.
>> +- operating-points-v2: the OPP table including frequency/voltage information
>> +  to support DVFS (Dynamic Voltage/Frequency Scaling) feature.
>> +- vdd-supply: the regulator to provide the buses with the voltage.
>> +- devfreq-events: the devfreq-event device to monitor the curret utilization
>> +  of buses.
>> +
>> +Optional properties for bus device:
>> +- exynos,saturation-ratio: the percentage value which is used to calibrate
>> +                   the performance count againt total cycle count.
>> +
>> +Example1:
>> +     Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to
>> +     power line (regulator). The MIF (Memory Interface) AXI bus is used to
>> +     transfer data between DRAM and CPU and uses the VDD_MIF regualtor.
>> +
>> +     - power line(VDD_MIF) --> bus for DMC block (dmc clock)
>> +
>> +     - MIF bus's frequency/voltage table
>> +     -----------------------
>> +     |Lv| Freq   | Voltage |
>> +     -----------------------
>> +     |L1| 50000  |800000   |
>> +     |L2| 100000 |800000   |
>> +     |L3| 133000 |800000   |
>> +     |L4| 200000 |800000   |
>> +     |L5| 400000 |875000   |
>> +     -----------------------
>> +
>> +Example2 :
>> +     The bus of DMC block in exynos3250.dtsi are listed below:
>
> What is DMC?

DMC (DRAM Memory Controller)

>
>> +
>> +     bus_dmc: bus_dmc {
>> +             compatible = "samsung,exynos-bus";
>
> I would expect the children of this bus to be under this node.

I add the detailed description on patch9 which is included in this
patch-set as follwoing.
- [RFC PATCH 09/15] PM / devfreq: exynos: Update documentation for bus
devices usingpassive governor

This patch-set don' include the the list of children node in parent dt node.
Instead, I add the separate node and then each children node has the
the phandle of parent node

>
>> +             clocks = <&cmu_dmc CLK_DIV_DMC>;
>> +             clock-names = "bus";
>> +             operating-points-v2 = <&bus_dmc_opp_table>;
>> +             status = "disabled";
>> +     };
>> +
>> +     bus_dmc_opp_table: opp_table0 {
>> +             compatible = "operating-points-v2";
>> +             opp-shared;
>> +
>> +             opp00 {
>> +                     opp-hz = /bits/ 64 <50000000>;
>> +                     opp-microvolt = <800000>;
>> +             };
>> +             opp01 {
>> +                     opp-hz = /bits/ 64 <100000000>;
>> +                     opp-microvolt = <800000>;
>> +             };
>> +             opp02 {
>> +                     opp-hz = /bits/ 64 <133000000>;
>> +                     opp-microvolt = <800000>;
>> +             };
>> +             opp03 {
>> +                     opp-hz = /bits/ 64 <200000000>;
>> +                     opp-microvolt = <800000>;
>> +             };
>> +             opp04 {
>> +                     opp-hz = /bits/ 64 <400000000>;
>> +                     opp-microvolt = <875000>;
>> +             };
>> +     };
>> +
>> +     Usage case to handle the frequency and voltage of bus on runtime
>> +     in exynos3250-rinato.dts are listed below:
>> +
>> +     &bus_dmc {
>> +             devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
>
> What do these phandles point to exactly?

DMC (DRAM Memory Controller) bus need to gather the current load in
bus on runtime.
The Exynos SoC has the PPMU (Platform Performance Monitoring Unit) for
sub-blocks.
The "ppmu_dmc0_3" and "ppmu_dmc1_3" measure the current load in DMC bus
with DEVFREQ-EVENT framework.

So, "bus_dmc" uses the load result from "ppmu_dmc0_3" and
"ppmu_dmc1_3" when deciding
the next bus frequency as basis data of dmc bus.

>
>> +             vdd-supply = <&buck1_reg>;      /* VDD_MIF */
>> +             status = "okay";
>> +     };
>> --
>> 1.9.1


Regards,
Chanwoo Choi

Re: [RFC PATCH 09/15] PM / devfreq: exynos: Update documentation for bus devices using passive governor

[Rob Herring]

On Thu, Nov 26, 2015 at 10:47:33PM +0900, Chanwoo Choi wrote:
> This patch updates the documentation for passive bus devices and adds the
> detailed example of Exynos3250.
> 
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> ---
>  .../devicetree/bindings/devfreq/exynos-bus.txt     | 226 ++++++++++++++++++++-
>  1 file changed, 223 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
> index 5d90623bd173..c4a6fe30075e 100644
> --- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
> +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
> @@ -12,18 +12,23 @@ SoC has the different sub-blocks. So, this difference should be specified
>  in devicetree file instead of each device driver. In result, this driver
>  is able to support the bus frequency for all Exynos SoCs.
>  
> -Required properties for bus device:
> +Required properties for all bus devices:
>  - compatible: Should be "samsung,exynos-bus".
>  - clock-names : the name of clock used by the bus, "bus".
>  - clocks : phandles for clock specified in "clock-names" property.
>  - #clock-cells: should be 1.
>  - operating-points-v2: the OPP table including frequency/voltage information
>    to support DVFS (Dynamic Voltage/Frequency Scaling) feature.
> +
> +Required properties for only parent bus device:
>  - vdd-supply: the regulator to provide the buses with the voltage.
>  - devfreq-events: the devfreq-event device to monitor the curret utilization
>    of buses.
>  
> -Optional properties for bus device:
> +Required properties for only passive bus device:
> +- devfreq: the parent bus device.
> +
> +Optional properties for only parent bus device:
>  - exynos,saturation-ratio: the percentage value which is used to calibrate
>                     the performance count againt total cycle count.
>  
> @@ -32,7 +37,19 @@ Example1:
>  	power line (regulator). The MIF (Memory Interface) AXI bus is used to
>  	transfer data between DRAM and CPU and uses the VDD_MIF regualtor.
>  
> -	- power line(VDD_MIF) --> bus for DMC block (dmc clock)
> +	- MIF (Memory Interface) block
> +	: VDD_MIF |--- DMC
> +
> +	- INT (Internal) block
> +	: VDD_INT |--- LEFTBUS  |--- PERIL
> +		  |    (parent) |--- MFC
> +		  |             |--- G3D
> +		  |
> +		  |--- RIGHTBUS |--- FSYS
> +				|--- LCD0
> +				|--- PERIR
> +				|--- ISP
> +				|--- CAM

I would expect the DT to mirror this topology which doesn't seem to be 
the case in the example.


>  	- MIF bus's frequency/voltage table
>  	-----------------------
> @@ -45,6 +62,20 @@ Example1:
>  	|L5| 400000 |875000   |
>  	-----------------------
>  
> +	- INT bus's frequency/voltage table
> +	-----------------------------------------------------------------------
> +	|Lv| Freq                                                   | Voltage |
> +	-----------------------------------------------------------------------
> +	|  |LEFTBUS|RIGHTBUS|LCD0   |FSYS   |MCUISP |ISP    |PERIL  |VDD_INT  |
> +	|  |*parent|passive |passive|passive|passive|passive|passive|         |
> +	-----------------------------------------------------------------------
> +	|L1|50000  |50000   |50000  |50000  |50000  |50000  |50000  |900000   |
> +	|L2|80000  |80000   |80000  |80000  |80000  |80000  |80000  |900000   |
> +	|L3|100000 |100000  |100000 |100000 |100000 |100000 |100000 |1000000  |
> +	|L4|133000 |133000  |133000 |133000 |200000 |200000 |       |1000000  |
> +	|L5|200000 |200000  |200000 |200000 |400000 |300000 |       |1000000  |
> +	-----------------------------------------------------------------------

Do you really have 5 states? It look like there are 2 to me because the 
OPP tables only really need to have the max freq at each voltage point. 

Rob

Re: [RFC PATCH 09/15] PM / devfreq: exynos: Update documentation for bus devices using passive governor

[Chanwoo Choi]

Hi Rob,

I'm sorry for delay reply due to the problem of email system
on the company.

On 2015년 12월 01일 06:14, Rob Herring wrote:
> On Thu, Nov 26, 2015 at 10:47:33PM +0900, Chanwoo Choi wrote:
>> This patch updates the documentation for passive bus devices and adds the
>> detailed example of Exynos3250.
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>> ---
>>  .../devicetree/bindings/devfreq/exynos-bus.txt     | 226 ++++++++++++++++++++-
>>  1 file changed, 223 insertions(+), 3 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
>> index 5d90623bd173..c4a6fe30075e 100644
>> --- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
>> +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
>> @@ -12,18 +12,23 @@ SoC has the different sub-blocks. So, this difference should be specified
>>  in devicetree file instead of each device driver. In result, this driver
>>  is able to support the bus frequency for all Exynos SoCs.
>>  
>> -Required properties for bus device:
>> +Required properties for all bus devices:
>>  - compatible: Should be "samsung,exynos-bus".
>>  - clock-names : the name of clock used by the bus, "bus".
>>  - clocks : phandles for clock specified in "clock-names" property.
>>  - #clock-cells: should be 1.
>>  - operating-points-v2: the OPP table including frequency/voltage information
>>    to support DVFS (Dynamic Voltage/Frequency Scaling) feature.
>> +
>> +Required properties for only parent bus device:
>>  - vdd-supply: the regulator to provide the buses with the voltage.
>>  - devfreq-events: the devfreq-event device to monitor the curret utilization
>>    of buses.
>>  
>> -Optional properties for bus device:
>> +Required properties for only passive bus device:
>> +- devfreq: the parent bus device.
>> +
>> +Optional properties for only parent bus device:
>>  - exynos,saturation-ratio: the percentage value which is used to calibrate
>>                     the performance count againt total cycle count.
>>  
>> @@ -32,7 +37,19 @@ Example1:
>>  	power line (regulator). The MIF (Memory Interface) AXI bus is used to
>>  	transfer data between DRAM and CPU and uses the VDD_MIF regualtor.
>>  
>> -	- power line(VDD_MIF) --> bus for DMC block (dmc clock)
>> +	- MIF (Memory Interface) block
>> +	: VDD_MIF |--- DMC
>> +
>> +	- INT (Internal) block
>> +	: VDD_INT |--- LEFTBUS  |--- PERIL
>> +		  |    (parent) |--- MFC
>> +		  |             |--- G3D
>> +		  |
>> +		  |--- RIGHTBUS |--- FSYS
>> +				|--- LCD0
>> +				|--- PERIR
>> +				|--- ISP
>> +				|--- CAM
> 
> I would expect the DT to mirror this topology which doesn't seem to be 
> the case in the example.

You're right. The above topology is not appropriate to show the correlation
between power line and sub blocks. I'll modify it as following.

The all blocks which are included in the INT (internal) block
share the one power line (VDD_INT).


	VDD_MIF |--- DMC

	VDD_INT |--- LEFTBUS
		|--- PERIL
		|--- MFC
		|--- G3D
		|--- RIGHTBUS
		|--- FSYS
		|--- LCD0
		|--- PERIR
		|--- ISP
		|--- CAM

> 
> 
>>  	- MIF bus's frequency/voltage table
>>  	-----------------------
>> @@ -45,6 +62,20 @@ Example1:
>>  	|L5| 400000 |875000   |
>>  	-----------------------
>>  
>> +	- INT bus's frequency/voltage table
>> +	-----------------------------------------------------------------------
>> +	|Lv| Freq                                                   | Voltage |
>> +	-----------------------------------------------------------------------
>> +	|  |LEFTBUS|RIGHTBUS|LCD0   |FSYS   |MCUISP |ISP    |PERIL  |VDD_INT  |
>> +	|  |*parent|passive |passive|passive|passive|passive|passive|         |
>> +	-----------------------------------------------------------------------
>> +	|L1|50000  |50000   |50000  |50000  |50000  |50000  |50000  |900000   |
>> +	|L2|80000  |80000   |80000  |80000  |80000  |80000  |80000  |900000   |
>> +	|L3|100000 |100000  |100000 |100000 |100000 |100000 |100000 |1000000  |
>> +	|L4|133000 |133000  |133000 |133000 |200000 |200000 |       |1000000  |
>> +	|L5|200000 |200000  |200000 |200000 |400000 |300000 |       |1000000  |
>> +	-----------------------------------------------------------------------
> 
> Do you really have 5 states? It look like there are 2 to me because the 
> OPP tables only really need to have the max freq at each voltage point. 

I'm sure. The OPP allow OPP table to add the same voltage for each OPP entry.
Instead, OPP don't permit adding the duplicate frequency. If OPP table includes
the different frequency as OPP entry, there is no problem. It is tested.

Regards,
Chanwoo Choi

Re: [RFC PATCH 01/15] PM / devfreq: exynos: Add generic exynos bus frequency driver

[Chanwoo Choi]

Hi Anand,

On 2015년 11월 27일 09:34, Chanwoo Choi wrote:
> Hi Anand,
> 
> On 2015년 11월 27일 02:17, Anand Moon wrote:
>> Hi Chanwoo,
>>
>> On 26 November 2015 at 21:42, Chanwoo Choi <cwchoi00@gmail.com> wrote:
>>> On Thu, Nov 26, 2015 at 11:00 PM, MyungJoo Ham <myungjoo.ham@samsung.com> wrote:
>>>> On Thu, Nov 26, 2015 at 10:47 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>>>>> This patch adds the generic exynos bus frequency driver for AMBA AXI bus
>>>>> of sub-blocks in exynos SoC with DEVFREQ framework. The Samsung Exynos SoC
>>>>> have the common architecture for bus between DRAM and sub-blocks in SoC.
>>>>> This driver can support the generic bus frequency driver for Exynos SoCs.
>>>>>
>>>>> In devicetree, Each bus block has a bus clock, regulator, operation-point
>>>>> and devfreq-event devices which measure the utilization of each bus block.
>>>>>
>>>>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>>>>> ---
>>>>>  drivers/devfreq/Kconfig             |  15 ++
>>>>>  drivers/devfreq/Makefile            |   1 +
>>>>>  drivers/devfreq/exynos/Makefile     |   1 +
>>>>>  drivers/devfreq/exynos/exynos-bus.c | 443 ++++++++++++++++++++++++++++++++++++
>>>>>  4 files changed, 460 insertions(+)
>>>>>  create mode 100644 drivers/devfreq/exynos/exynos-bus.c
>>>>>
>>>>
>>>> Are we finally getting a common Exynos bus driver with full DT support?
>>>> (can this replace both Exynos4/5 drivers and support Exynos7 series?)
>>>
>>> Yes.
>>> This patch-set would support all Exynos SoCs for bus frequency driver.
>>> To make sure the support for Exynos7 series, I need to check the TRM
>>> document of Exynos7.  I think it is possible for support Exynos7.
>>>
>>> I'm going to test this driver on various Exynos-based board.
>>>
>>> Regards,
>>> Chanwoo Choi
>>
>> Please do consider Exynos 542x series as well.
> 
> Sure. I'll to test it on Exynos5422-based Odroid-XU3.

I send the v2 patchset but this patchset don't include
the support of Odroid-XU3 because of only Exynos542x has the 
special addtional sequence to change the source clock
of DRAM. So, I'm going to support the bus frequency on Exynos542x.
After completing it, I'll send the separate patches.

Thanks,
Chanwoo Choi

Re: [RFC PATCH 01/15] PM / devfreq: exynos: Add generic exynos bus frequency driver

[Anand Moon]

Hi Chanwoo,

On 9 December 2015 at 09:41, Chanwoo Choi <cw00.choi@samsung.com> wrote:
> Hi Anand,
>
> On 2015년 11월 27일 09:34, Chanwoo Choi wrote:
>> Hi Anand,
>>
>> On 2015년 11월 27일 02:17, Anand Moon wrote:
>>> Hi Chanwoo,
>>>
>>> On 26 November 2015 at 21:42, Chanwoo Choi <cwchoi00@gmail.com> wrote:
>>>> On Thu, Nov 26, 2015 at 11:00 PM, MyungJoo Ham <myungjoo.ham@samsung.com> wrote:
>>>>> On Thu, Nov 26, 2015 at 10:47 PM, Chanwoo Choi <cw00.choi@samsung.com> wrote:
>>>>>> This patch adds the generic exynos bus frequency driver for AMBA AXI bus
>>>>>> of sub-blocks in exynos SoC with DEVFREQ framework. The Samsung Exynos SoC
>>>>>> have the common architecture for bus between DRAM and sub-blocks in SoC.
>>>>>> This driver can support the generic bus frequency driver for Exynos SoCs.
>>>>>>
>>>>>> In devicetree, Each bus block has a bus clock, regulator, operation-point
>>>>>> and devfreq-event devices which measure the utilization of each bus block.
>>>>>>
>>>>>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>>>>>> ---
>>>>>>  drivers/devfreq/Kconfig             |  15 ++
>>>>>>  drivers/devfreq/Makefile            |   1 +
>>>>>>  drivers/devfreq/exynos/Makefile     |   1 +
>>>>>>  drivers/devfreq/exynos/exynos-bus.c | 443 ++++++++++++++++++++++++++++++++++++
>>>>>>  4 files changed, 460 insertions(+)
>>>>>>  create mode 100644 drivers/devfreq/exynos/exynos-bus.c
>>>>>>
>>>>>
>>>>> Are we finally getting a common Exynos bus driver with full DT support?
>>>>> (can this replace both Exynos4/5 drivers and support Exynos7 series?)
>>>>
>>>> Yes.
>>>> This patch-set would support all Exynos SoCs for bus frequency driver.
>>>> To make sure the support for Exynos7 series, I need to check the TRM
>>>> document of Exynos7.  I think it is possible for support Exynos7.
>>>>
>>>> I'm going to test this driver on various Exynos-based board.
>>>>
>>>> Regards,
>>>> Chanwoo Choi
>>>
>>> Please do consider Exynos 542x series as well.
>>
>> Sure. I'll to test it on Exynos5422-based Odroid-XU3.
>
> I send the v2 patchset but this patchset don't include
> the support of Odroid-XU3 because of only Exynos542x has the
> special addtional sequence to change the source clock
> of DRAM. So, I'm going to support the bus frequency on Exynos542x.
> After completing it, I'll send the separate patches.
>
> Thanks,
> Chanwoo Choi
>

Not an issue. Thanks for the update.

-Anand Moon