* [PATCH v8 1/3] dt-bindings: remoteproc: add Tightly Coupled Memory (TCM) bindings
2023-12-15 23:57 [PATCH v8 0/3] add zynqmp TCM bindings Tanmay Shah
@ 2023-12-15 23:57 ` Tanmay Shah
2023-12-15 23:57 ` [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc Tanmay Shah
2023-12-15 23:57 ` [PATCH v8 3/3] remoteproc: zynqmp: parse TCM from device tree Tanmay Shah
2 siblings, 0 replies; 13+ messages in thread
From: Tanmay Shah @ 2023-12-15 23:57 UTC (permalink / raw)
To: andersson, mathieu.poirier, robh+dt, krzysztof.kozlowski+dt,
conor+dt, michal.simek, ben.levinsky, tanmay.shah
Cc: linux-remoteproc, devicetree, linux-arm-kernel, linux-kernel,
Radhey Shyam Pandey, Rob Herring
From: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Introduce bindings for TCM memory address space on AMD-xilinx Zynq
UltraScale+ platform. It will help in defining TCM in device-tree
and make it's access platform agnostic and data-driven.
Tightly-coupled memories(TCMs) are low-latency memory that provides
predictable instruction execution and predictable data load/store
timing. Each Cortex-R5F processor contains two 64-bit wide 64 KB memory
banks on the ATCM and BTCM ports, for a total of 128 KB of memory.
The TCM resources(reg, reg-names and power-domain) are documented for
each TCM in the R5 node. The reg and reg-names are made as required
properties as we don't want to hardcode TCM addresses for future
platforms and for zu+ legacy implementation will ensure that the
old dts w/o reg/reg-names works and stable ABI is maintained.
It also extends the examples for TCM split and lockstep modes.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../remoteproc/xlnx,zynqmp-r5fss.yaml | 131 +++++++++++++++---
1 file changed, 113 insertions(+), 18 deletions(-)
diff --git a/Documentation/devicetree/bindings/remoteproc/xlnx,zynqmp-r5fss.yaml b/Documentation/devicetree/bindings/remoteproc/xlnx,zynqmp-r5fss.yaml
index 78aac69f1060..9ecd63ea1b38 100644
--- a/Documentation/devicetree/bindings/remoteproc/xlnx,zynqmp-r5fss.yaml
+++ b/Documentation/devicetree/bindings/remoteproc/xlnx,zynqmp-r5fss.yaml
@@ -20,6 +20,17 @@ properties:
compatible:
const: xlnx,zynqmp-r5fss
+ "#address-cells":
+ const: 2
+
+ "#size-cells":
+ const: 2
+
+ ranges:
+ description: |
+ Standard ranges definition providing address translations for
+ local R5F TCM address spaces to bus addresses.
+
xlnx,cluster-mode:
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1, 2]
@@ -37,7 +48,7 @@ properties:
2: single cpu mode
patternProperties:
- "^r5f-[a-f0-9]+$":
+ "^r5f@[0-9a-f]+$":
type: object
description: |
The RPU is located in the Low Power Domain of the Processor Subsystem.
@@ -54,8 +65,19 @@ patternProperties:
compatible:
const: xlnx,zynqmp-r5f
+ reg:
+ items:
+ - description: ATCM internal memory region
+ - description: BTCM internal memory region
+
+ reg-names:
+ items:
+ - const: atcm
+ - const: btcm
+
power-domains:
- maxItems: 1
+ minItems: 1
+ maxItems: 3
mboxes:
minItems: 1
@@ -102,34 +124,107 @@ patternProperties:
required:
- compatible
- power-domains
+ - reg
+ - reg-names
unevaluatedProperties: false
required:
- compatible
+ - "#address-cells"
+ - "#size-cells"
+ - ranges
additionalProperties: false
examples:
- |
- remoteproc {
- compatible = "xlnx,zynqmp-r5fss";
- xlnx,cluster-mode = <1>;
-
- r5f-0 {
- compatible = "xlnx,zynqmp-r5f";
- power-domains = <&zynqmp_firmware 0x7>;
- memory-region = <&rproc_0_fw_image>, <&rpu0vdev0buffer>, <&rpu0vdev0vring0>, <&rpu0vdev0vring1>;
- mboxes = <&ipi_mailbox_rpu0 0>, <&ipi_mailbox_rpu0 1>;
- mbox-names = "tx", "rx";
+ #include <dt-bindings/power/xlnx-zynqmp-power.h>
+
+ //Split mode configuration
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ remoteproc@ffe00000 {
+ compatible = "xlnx,zynqmp-r5fss";
+ xlnx,cluster-mode = <0>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x10000>,
+ <0x0 0x20000 0x0 0xffe20000 0x0 0x10000>,
+ <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
+ <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
+
+ r5f@0 {
+ compatible = "xlnx,zynqmp-r5f";
+ reg = <0x0 0x0 0x0 0x10000>, <0x0 0x20000 0x0 0x10000>;
+ reg-names = "atcm", "btcm";
+ power-domains = <&zynqmp_firmware PD_RPU_0>,
+ <&zynqmp_firmware PD_R5_0_ATCM>,
+ <&zynqmp_firmware PD_R5_0_BTCM>;
+ memory-region = <&rproc_0_fw_image>, <&rpu0vdev0buffer>,
+ <&rpu0vdev0vring0>, <&rpu0vdev0vring1>;
+ mboxes = <&ipi_mailbox_rpu0 0>, <&ipi_mailbox_rpu0 1>;
+ mbox-names = "tx", "rx";
+ };
+
+ r5f@1 {
+ compatible = "xlnx,zynqmp-r5f";
+ reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
+ reg-names = "atcm", "btcm";
+ power-domains = <&zynqmp_firmware PD_RPU_1>,
+ <&zynqmp_firmware PD_R5_1_ATCM>,
+ <&zynqmp_firmware PD_R5_1_BTCM>;
+ memory-region = <&rproc_1_fw_image>, <&rpu1vdev0buffer>,
+ <&rpu1vdev0vring0>, <&rpu1vdev0vring1>;
+ mboxes = <&ipi_mailbox_rpu1 0>, <&ipi_mailbox_rpu1 1>;
+ mbox-names = "tx", "rx";
+ };
};
+ };
- r5f-1 {
- compatible = "xlnx,zynqmp-r5f";
- power-domains = <&zynqmp_firmware 0x8>;
- memory-region = <&rproc_1_fw_image>, <&rpu1vdev0buffer>, <&rpu1vdev0vring0>, <&rpu1vdev0vring1>;
- mboxes = <&ipi_mailbox_rpu1 0>, <&ipi_mailbox_rpu1 1>;
- mbox-names = "tx", "rx";
+ - |
+ //Lockstep configuration
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ remoteproc@ffe00000 {
+ compatible = "xlnx,zynqmp-r5fss";
+ xlnx,cluster-mode = <1>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x20000>,
+ <0x0 0x20000 0x0 0xffe20000 0x0 0x20000>;
+
+ r5f@0 {
+ compatible = "xlnx,zynqmp-r5f";
+ reg = <0x0 0x0 0x0 0x20000>, <0x0 0x20000 0x0 0x20000>;
+ reg-names = "atcm", "btcm";
+ power-domains = <&zynqmp_firmware PD_RPU_0>,
+ <&zynqmp_firmware PD_R5_0_ATCM>,
+ <&zynqmp_firmware PD_R5_0_BTCM>;
+ memory-region = <&rproc_0_fw_image>, <&rpu0vdev0buffer>,
+ <&rpu0vdev0vring0>, <&rpu0vdev0vring1>;
+ mboxes = <&ipi_mailbox_rpu0 0>, <&ipi_mailbox_rpu0 1>;
+ mbox-names = "tx", "rx";
+ };
+
+ r5f@1 {
+ compatible = "xlnx,zynqmp-r5f";
+ reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
+ reg-names = "atcm", "btcm";
+ power-domains = <&zynqmp_firmware PD_RPU_1>,
+ <&zynqmp_firmware PD_R5_1_ATCM>,
+ <&zynqmp_firmware PD_R5_1_BTCM>;
+ memory-region = <&rproc_1_fw_image>, <&rpu1vdev0buffer>,
+ <&rpu1vdev0vring0>, <&rpu1vdev0vring1>;
+ mboxes = <&ipi_mailbox_rpu1 0>, <&ipi_mailbox_rpu1 1>;
+ mbox-names = "tx", "rx";
+ };
};
};
...
--
2.25.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc
2023-12-15 23:57 [PATCH v8 0/3] add zynqmp TCM bindings Tanmay Shah
2023-12-15 23:57 ` [PATCH v8 1/3] dt-bindings: remoteproc: add Tightly Coupled Memory (TCM) bindings Tanmay Shah
@ 2023-12-15 23:57 ` Tanmay Shah
2023-12-20 13:14 ` Michal Simek
2024-01-03 17:54 ` Mathieu Poirier
2023-12-15 23:57 ` [PATCH v8 3/3] remoteproc: zynqmp: parse TCM from device tree Tanmay Shah
2 siblings, 2 replies; 13+ messages in thread
From: Tanmay Shah @ 2023-12-15 23:57 UTC (permalink / raw)
To: andersson, mathieu.poirier, robh+dt, krzysztof.kozlowski+dt,
conor+dt, michal.simek, ben.levinsky, tanmay.shah
Cc: linux-remoteproc, devicetree, linux-arm-kernel, linux-kernel
Add properties as per new bindings in zynqmp remoteproc node
to represent TCM address and size.
This patch also adds alternative remoteproc node to represent
remoteproc cluster in split mode. By default lockstep mode is
enabled and users should disable it before using split mode
dts. Both device-tree nodes can't be used simultaneously one
of them must be disabled. For zcu102-1.0 and zcu102-1.1 board
remoteproc split mode dts node is enabled and lockstep mode
dts is disabled.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
---
.../boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 8 +++
arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 60 +++++++++++++++++--
2 files changed, 63 insertions(+), 5 deletions(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
index c8f71a1aec89..495ca94b45db 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
@@ -14,6 +14,14 @@ / {
compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
};
+&rproc_split {
+ status = "okay";
+};
+
+&rproc_lockstep {
+ status = "disabled";
+};
+
&eeprom {
#address-cells = <1>;
#size-cells = <1>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
index b61fc99cd911..602e6aba7ac5 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
+++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
@@ -247,19 +247,69 @@ fpga_full: fpga-full {
ranges;
};
- remoteproc {
+ rproc_lockstep: remoteproc@ffe00000 {
compatible = "xlnx,zynqmp-r5fss";
xlnx,cluster-mode = <1>;
- r5f-0 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x20000>,
+ <0x0 0x20000 0x0 0xffe20000 0x0 0x20000>,
+ <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
+ <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
+
+ r5f@0 {
+ compatible = "xlnx,zynqmp-r5f";
+ reg = <0x0 0x0 0x0 0x20000>, <0x0 0x20000 0x0 0x20000>;
+ reg-names = "atcm", "btcm";
+ power-domains = <&zynqmp_firmware PD_RPU_0>,
+ <&zynqmp_firmware PD_R5_0_ATCM>,
+ <&zynqmp_firmware PD_R5_0_BTCM>;
+ memory-region = <&rproc_0_fw_image>;
+ };
+
+ r5f@1 {
+ compatible = "xlnx,zynqmp-r5f";
+ reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
+ reg-names = "atcm", "btcm";
+ power-domains = <&zynqmp_firmware PD_RPU_1>,
+ <&zynqmp_firmware PD_R5_1_ATCM>,
+ <&zynqmp_firmware PD_R5_1_BTCM>;
+ memory-region = <&rproc_1_fw_image>;
+ };
+ };
+
+ rproc_split: remoteproc-split@ffe00000 {
+ status = "disabled";
+ compatible = "xlnx,zynqmp-r5fss";
+ xlnx,cluster-mode = <0>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x10000>,
+ <0x0 0x20000 0x0 0xffe20000 0x0 0x10000>,
+ <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
+ <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
+
+ r5f@0 {
compatible = "xlnx,zynqmp-r5f";
- power-domains = <&zynqmp_firmware PD_RPU_0>;
+ reg = <0x0 0x0 0x0 0x10000>, <0x0 0x20000 0x0 0x10000>;
+ reg-names = "atcm", "btcm";
+ power-domains = <&zynqmp_firmware PD_RPU_0>,
+ <&zynqmp_firmware PD_R5_0_ATCM>,
+ <&zynqmp_firmware PD_R5_0_BTCM>;
memory-region = <&rproc_0_fw_image>;
};
- r5f-1 {
+ r5f@1 {
compatible = "xlnx,zynqmp-r5f";
- power-domains = <&zynqmp_firmware PD_RPU_1>;
+ reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
+ reg-names = "atcm", "btcm";
+ power-domains = <&zynqmp_firmware PD_RPU_1>,
+ <&zynqmp_firmware PD_R5_1_ATCM>,
+ <&zynqmp_firmware PD_R5_1_BTCM>;
memory-region = <&rproc_1_fw_image>;
};
};
--
2.25.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc
2023-12-15 23:57 ` [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc Tanmay Shah
@ 2023-12-20 13:14 ` Michal Simek
2023-12-20 14:45 ` Tanmay Shah
2024-01-03 17:54 ` Mathieu Poirier
1 sibling, 1 reply; 13+ messages in thread
From: Michal Simek @ 2023-12-20 13:14 UTC (permalink / raw)
To: Tanmay Shah, andersson, mathieu.poirier, robh+dt,
krzysztof.kozlowski+dt, conor+dt, ben.levinsky
Cc: linux-remoteproc, devicetree, linux-arm-kernel, linux-kernel
On 12/16/23 00:57, Tanmay Shah wrote:
> Add properties as per new bindings in zynqmp remoteproc node
> to represent TCM address and size.
>
> This patch also adds alternative remoteproc node to represent
> remoteproc cluster in split mode. By default lockstep mode is
> enabled and users should disable it before using split mode
> dts. Both device-tree nodes can't be used simultaneously one
> of them must be disabled. For zcu102-1.0 and zcu102-1.1 board
> remoteproc split mode dts node is enabled and lockstep mode
> dts is disabled.
>
> Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
> ---
> .../boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 8 +++
> arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 60 +++++++++++++++++--
> 2 files changed, 63 insertions(+), 5 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> index c8f71a1aec89..495ca94b45db 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> @@ -14,6 +14,14 @@ / {
> compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
> };
>
> +&rproc_split {
> + status = "okay";
> +};
> +
> +&rproc_lockstep {
> + status = "disabled";
> +};
> +
> &eeprom {
> #address-cells = <1>;
> #size-cells = <1>;
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> index b61fc99cd911..602e6aba7ac5 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> @@ -247,19 +247,69 @@ fpga_full: fpga-full {
> ranges;
> };
>
> - remoteproc {
> + rproc_lockstep: remoteproc@ffe00000 {
> compatible = "xlnx,zynqmp-r5fss";
> xlnx,cluster-mode = <1>;
>
> - r5f-0 {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x20000>,
> + <0x0 0x20000 0x0 0xffe20000 0x0 0x20000>,
> + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
> +
> + r5f@0 {
> + compatible = "xlnx,zynqmp-r5f";
> + reg = <0x0 0x0 0x0 0x20000>, <0x0 0x20000 0x0 0x20000>;
> + reg-names = "atcm", "btcm";
> + power-domains = <&zynqmp_firmware PD_RPU_0>,
> + <&zynqmp_firmware PD_R5_0_ATCM>,
> + <&zynqmp_firmware PD_R5_0_BTCM>;
> + memory-region = <&rproc_0_fw_image>;
> + };
> +
> + r5f@1 {
> + compatible = "xlnx,zynqmp-r5f";
> + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> + reg-names = "atcm", "btcm";
> + power-domains = <&zynqmp_firmware PD_RPU_1>,
> + <&zynqmp_firmware PD_R5_1_ATCM>,
> + <&zynqmp_firmware PD_R5_1_BTCM>;
> + memory-region = <&rproc_1_fw_image>;
> + };
> + };
> +
> + rproc_split: remoteproc-split@ffe00000 {
> + status = "disabled";
> + compatible = "xlnx,zynqmp-r5fss";
> + xlnx,cluster-mode = <0>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x10000>,
> + <0x0 0x20000 0x0 0xffe20000 0x0 0x10000>,
> + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
> +
> + r5f@0 {
> compatible = "xlnx,zynqmp-r5f";
> - power-domains = <&zynqmp_firmware PD_RPU_0>;
> + reg = <0x0 0x0 0x0 0x10000>, <0x0 0x20000 0x0 0x10000>;
> + reg-names = "atcm", "btcm";
> + power-domains = <&zynqmp_firmware PD_RPU_0>,
> + <&zynqmp_firmware PD_R5_0_ATCM>,
> + <&zynqmp_firmware PD_R5_0_BTCM>;
> memory-region = <&rproc_0_fw_image>;
> };
>
> - r5f-1 {
> + r5f@1 {
> compatible = "xlnx,zynqmp-r5f";
> - power-domains = <&zynqmp_firmware PD_RPU_1>;
> + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> + reg-names = "atcm", "btcm";
> + power-domains = <&zynqmp_firmware PD_RPU_1>,
> + <&zynqmp_firmware PD_R5_1_ATCM>,
> + <&zynqmp_firmware PD_R5_1_BTCM>;
> memory-region = <&rproc_1_fw_image>;
> };
> };
Acked-by: Michal Simek <michal.simek@amd.com>
Let me know if you want me to take this via my tree.
Thanks,
Michal
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc
2023-12-20 13:14 ` Michal Simek
@ 2023-12-20 14:45 ` Tanmay Shah
2023-12-23 14:34 ` Mathieu Poirier
0 siblings, 1 reply; 13+ messages in thread
From: Tanmay Shah @ 2023-12-20 14:45 UTC (permalink / raw)
To: Michal Simek, andersson, mathieu.poirier, robh+dt,
krzysztof.kozlowski+dt, conor+dt, ben.levinsky
Cc: linux-remoteproc, devicetree, linux-arm-kernel, linux-kernel
On 12/20/23 7:14 AM, Michal Simek wrote:
>
> On 12/16/23 00:57, Tanmay Shah wrote:
> > Add properties as per new bindings in zynqmp remoteproc node
> > to represent TCM address and size.
> >
> > This patch also adds alternative remoteproc node to represent
> > remoteproc cluster in split mode. By default lockstep mode is
> > enabled and users should disable it before using split mode
> > dts. Both device-tree nodes can't be used simultaneously one
> > of them must be disabled. For zcu102-1.0 and zcu102-1.1 board
> > remoteproc split mode dts node is enabled and lockstep mode
> > dts is disabled.
> >
> > Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
> > ---
> > .../boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 8 +++
> > arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 60 +++++++++++++++++--
> > 2 files changed, 63 insertions(+), 5 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > index c8f71a1aec89..495ca94b45db 100644
> > --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > @@ -14,6 +14,14 @@ / {
> > compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
> > };
> >
> > +&rproc_split {
> > + status = "okay";
> > +};
> > +
> > +&rproc_lockstep {
> > + status = "disabled";
> > +};
> > +
> > &eeprom {
> > #address-cells = <1>;
> > #size-cells = <1>;
> > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > index b61fc99cd911..602e6aba7ac5 100644
> > --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > @@ -247,19 +247,69 @@ fpga_full: fpga-full {
> > ranges;
> > };
> >
> > - remoteproc {
> > + rproc_lockstep: remoteproc@ffe00000 {
> > compatible = "xlnx,zynqmp-r5fss";
> > xlnx,cluster-mode = <1>;
> >
> > - r5f-0 {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x20000>,
> > + <0x0 0x20000 0x0 0xffe20000 0x0 0x20000>,
> > + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> > + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
> > +
> > + r5f@0 {
> > + compatible = "xlnx,zynqmp-r5f";
> > + reg = <0x0 0x0 0x0 0x20000>, <0x0 0x20000 0x0 0x20000>;
> > + reg-names = "atcm", "btcm";
> > + power-domains = <&zynqmp_firmware PD_RPU_0>,
> > + <&zynqmp_firmware PD_R5_0_ATCM>,
> > + <&zynqmp_firmware PD_R5_0_BTCM>;
> > + memory-region = <&rproc_0_fw_image>;
> > + };
> > +
> > + r5f@1 {
> > + compatible = "xlnx,zynqmp-r5f";
> > + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> > + reg-names = "atcm", "btcm";
> > + power-domains = <&zynqmp_firmware PD_RPU_1>,
> > + <&zynqmp_firmware PD_R5_1_ATCM>,
> > + <&zynqmp_firmware PD_R5_1_BTCM>;
> > + memory-region = <&rproc_1_fw_image>;
> > + };
> > + };
> > +
> > + rproc_split: remoteproc-split@ffe00000 {
> > + status = "disabled";
> > + compatible = "xlnx,zynqmp-r5fss";
> > + xlnx,cluster-mode = <0>;
> > +
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x10000>,
> > + <0x0 0x20000 0x0 0xffe20000 0x0 0x10000>,
> > + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> > + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
> > +
> > + r5f@0 {
> > compatible = "xlnx,zynqmp-r5f";
> > - power-domains = <&zynqmp_firmware PD_RPU_0>;
> > + reg = <0x0 0x0 0x0 0x10000>, <0x0 0x20000 0x0 0x10000>;
> > + reg-names = "atcm", "btcm";
> > + power-domains = <&zynqmp_firmware PD_RPU_0>,
> > + <&zynqmp_firmware PD_R5_0_ATCM>,
> > + <&zynqmp_firmware PD_R5_0_BTCM>;
> > memory-region = <&rproc_0_fw_image>;
> > };
> >
> > - r5f-1 {
> > + r5f@1 {
> > compatible = "xlnx,zynqmp-r5f";
> > - power-domains = <&zynqmp_firmware PD_RPU_1>;
> > + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> > + reg-names = "atcm", "btcm";
> > + power-domains = <&zynqmp_firmware PD_RPU_1>,
> > + <&zynqmp_firmware PD_R5_1_ATCM>,
> > + <&zynqmp_firmware PD_R5_1_BTCM>;
> > memory-region = <&rproc_1_fw_image>;
> > };
> > };
>
> Acked-by: Michal Simek <michal.simek@amd.com>
>
> Let me know if you want me to take this via my tree.
Hi Michal,
Thanks for reviews. I will ping you once driver changes are approved.
Or Mathieu can take this in remoteproc tree, either way is fine.
But I would like to wait till driver changes are approved.
Tanmay
>
> Thanks,
> Michal
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc
2023-12-20 14:45 ` Tanmay Shah
@ 2023-12-23 14:34 ` Mathieu Poirier
0 siblings, 0 replies; 13+ messages in thread
From: Mathieu Poirier @ 2023-12-23 14:34 UTC (permalink / raw)
To: Tanmay Shah
Cc: Michal Simek, andersson, robh+dt, krzysztof.kozlowski+dt,
conor+dt, ben.levinsky, linux-remoteproc, devicetree,
linux-arm-kernel, linux-kernel
On Wed, 20 Dec 2023 at 07:45, Tanmay Shah <tanmay.shah@amd.com> wrote:
>
>
> On 12/20/23 7:14 AM, Michal Simek wrote:
> >
> > On 12/16/23 00:57, Tanmay Shah wrote:
> > > Add properties as per new bindings in zynqmp remoteproc node
> > > to represent TCM address and size.
> > >
> > > This patch also adds alternative remoteproc node to represent
> > > remoteproc cluster in split mode. By default lockstep mode is
> > > enabled and users should disable it before using split mode
> > > dts. Both device-tree nodes can't be used simultaneously one
> > > of them must be disabled. For zcu102-1.0 and zcu102-1.1 board
> > > remoteproc split mode dts node is enabled and lockstep mode
> > > dts is disabled.
> > >
> > > Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
> > > ---
> > > .../boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 8 +++
> > > arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 60 +++++++++++++++++--
> > > 2 files changed, 63 insertions(+), 5 deletions(-)
> > >
> > > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > > index c8f71a1aec89..495ca94b45db 100644
> > > --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > > @@ -14,6 +14,14 @@ / {
> > > compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
> > > };
> > >
> > > +&rproc_split {
> > > + status = "okay";
> > > +};
> > > +
> > > +&rproc_lockstep {
> > > + status = "disabled";
> > > +};
> > > +
> > > &eeprom {
> > > #address-cells = <1>;
> > > #size-cells = <1>;
> > > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > > index b61fc99cd911..602e6aba7ac5 100644
> > > --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > > +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > > @@ -247,19 +247,69 @@ fpga_full: fpga-full {
> > > ranges;
> > > };
> > >
> > > - remoteproc {
> > > + rproc_lockstep: remoteproc@ffe00000 {
> > > compatible = "xlnx,zynqmp-r5fss";
> > > xlnx,cluster-mode = <1>;
> > >
> > > - r5f-0 {
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > +
> > > + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x20000>,
> > > + <0x0 0x20000 0x0 0xffe20000 0x0 0x20000>,
> > > + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> > > + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
> > > +
> > > + r5f@0 {
> > > + compatible = "xlnx,zynqmp-r5f";
> > > + reg = <0x0 0x0 0x0 0x20000>, <0x0 0x20000 0x0 0x20000>;
> > > + reg-names = "atcm", "btcm";
> > > + power-domains = <&zynqmp_firmware PD_RPU_0>,
> > > + <&zynqmp_firmware PD_R5_0_ATCM>,
> > > + <&zynqmp_firmware PD_R5_0_BTCM>;
> > > + memory-region = <&rproc_0_fw_image>;
> > > + };
> > > +
> > > + r5f@1 {
> > > + compatible = "xlnx,zynqmp-r5f";
> > > + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> > > + reg-names = "atcm", "btcm";
> > > + power-domains = <&zynqmp_firmware PD_RPU_1>,
> > > + <&zynqmp_firmware PD_R5_1_ATCM>,
> > > + <&zynqmp_firmware PD_R5_1_BTCM>;
> > > + memory-region = <&rproc_1_fw_image>;
> > > + };
> > > + };
> > > +
> > > + rproc_split: remoteproc-split@ffe00000 {
> > > + status = "disabled";
> > > + compatible = "xlnx,zynqmp-r5fss";
> > > + xlnx,cluster-mode = <0>;
> > > +
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > +
> > > + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x10000>,
> > > + <0x0 0x20000 0x0 0xffe20000 0x0 0x10000>,
> > > + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> > > + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
> > > +
> > > + r5f@0 {
> > > compatible = "xlnx,zynqmp-r5f";
> > > - power-domains = <&zynqmp_firmware PD_RPU_0>;
> > > + reg = <0x0 0x0 0x0 0x10000>, <0x0 0x20000 0x0 0x10000>;
> > > + reg-names = "atcm", "btcm";
> > > + power-domains = <&zynqmp_firmware PD_RPU_0>,
> > > + <&zynqmp_firmware PD_R5_0_ATCM>,
> > > + <&zynqmp_firmware PD_R5_0_BTCM>;
> > > memory-region = <&rproc_0_fw_image>;
> > > };
> > >
> > > - r5f-1 {
> > > + r5f@1 {
> > > compatible = "xlnx,zynqmp-r5f";
> > > - power-domains = <&zynqmp_firmware PD_RPU_1>;
> > > + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> > > + reg-names = "atcm", "btcm";
> > > + power-domains = <&zynqmp_firmware PD_RPU_1>,
> > > + <&zynqmp_firmware PD_R5_1_ATCM>,
> > > + <&zynqmp_firmware PD_R5_1_BTCM>;
> > > memory-region = <&rproc_1_fw_image>;
> > > };
> > > };
> >
> > Acked-by: Michal Simek <michal.simek@amd.com>
> >
> > Let me know if you want me to take this via my tree.
>
> Hi Michal,
>
> Thanks for reviews. I will ping you once driver changes are approved.
I'll pick this up with the rest of the driver. It will be easier that way.
>
> Or Mathieu can take this in remoteproc tree, either way is fine.
>
> But I would like to wait till driver changes are approved.
>
> Tanmay
>
> >
> > Thanks,
> > Michal
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc
2023-12-15 23:57 ` [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc Tanmay Shah
2023-12-20 13:14 ` Michal Simek
@ 2024-01-03 17:54 ` Mathieu Poirier
2024-01-03 18:19 ` Tanmay Shah
1 sibling, 1 reply; 13+ messages in thread
From: Mathieu Poirier @ 2024-01-03 17:54 UTC (permalink / raw)
To: Tanmay Shah
Cc: andersson, robh+dt, krzysztof.kozlowski+dt, conor+dt,
michal.simek, ben.levinsky, linux-remoteproc, devicetree,
linux-arm-kernel, linux-kernel
Hi Tanmay,
On Fri, Dec 15, 2023 at 03:57:24PM -0800, Tanmay Shah wrote:
> Add properties as per new bindings in zynqmp remoteproc node
> to represent TCM address and size.
>
> This patch also adds alternative remoteproc node to represent
> remoteproc cluster in split mode. By default lockstep mode is
> enabled and users should disable it before using split mode
> dts. Both device-tree nodes can't be used simultaneously one
> of them must be disabled. For zcu102-1.0 and zcu102-1.1 board
> remoteproc split mode dts node is enabled and lockstep mode
> dts is disabled.
>
> Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
> ---
> .../boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 8 +++
> arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 60 +++++++++++++++++--
> 2 files changed, 63 insertions(+), 5 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> index c8f71a1aec89..495ca94b45db 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> @@ -14,6 +14,14 @@ / {
> compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
> };
>
> +&rproc_split {
> + status = "okay";
> +};
> +
> +&rproc_lockstep {
> + status = "disabled";
> +};
> +
> &eeprom {
> #address-cells = <1>;
> #size-cells = <1>;
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> index b61fc99cd911..602e6aba7ac5 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> @@ -247,19 +247,69 @@ fpga_full: fpga-full {
> ranges;
> };
>
> - remoteproc {
> + rproc_lockstep: remoteproc@ffe00000 {
> compatible = "xlnx,zynqmp-r5fss";
> xlnx,cluster-mode = <1>;
>
> - r5f-0 {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x20000>,
> + <0x0 0x20000 0x0 0xffe20000 0x0 0x20000>,
> + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
As far as I can tell, in lockstep mode the last two entries are not needed.
This is also contrasting with that is in the bindings, which is quite confusing.
> +
> + r5f@0 {
> + compatible = "xlnx,zynqmp-r5f";
> + reg = <0x0 0x0 0x0 0x20000>, <0x0 0x20000 0x0 0x20000>;
> + reg-names = "atcm", "btcm";
> + power-domains = <&zynqmp_firmware PD_RPU_0>,
> + <&zynqmp_firmware PD_R5_0_ATCM>,
> + <&zynqmp_firmware PD_R5_0_BTCM>;
> + memory-region = <&rproc_0_fw_image>;
> + };
> +
> + r5f@1 {
> + compatible = "xlnx,zynqmp-r5f";
> + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> + reg-names = "atcm", "btcm";
> + power-domains = <&zynqmp_firmware PD_RPU_1>,
> + <&zynqmp_firmware PD_R5_1_ATCM>,
> + <&zynqmp_firmware PD_R5_1_BTCM>;
> + memory-region = <&rproc_1_fw_image>;
> + };
> + };
> +
> + rproc_split: remoteproc-split@ffe00000 {
> + status = "disabled";
> + compatible = "xlnx,zynqmp-r5fss";
> + xlnx,cluster-mode = <0>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x10000>,
> + <0x0 0x20000 0x0 0xffe20000 0x0 0x10000>,
> + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
> +
> + r5f@0 {
> compatible = "xlnx,zynqmp-r5f";
> - power-domains = <&zynqmp_firmware PD_RPU_0>;
> + reg = <0x0 0x0 0x0 0x10000>, <0x0 0x20000 0x0 0x10000>;
> + reg-names = "atcm", "btcm";
> + power-domains = <&zynqmp_firmware PD_RPU_0>,
> + <&zynqmp_firmware PD_R5_0_ATCM>,
> + <&zynqmp_firmware PD_R5_0_BTCM>;
> memory-region = <&rproc_0_fw_image>;
> };
>
> - r5f-1 {
> + r5f@1 {
> compatible = "xlnx,zynqmp-r5f";
> - power-domains = <&zynqmp_firmware PD_RPU_1>;
> + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> + reg-names = "atcm", "btcm";
> + power-domains = <&zynqmp_firmware PD_RPU_1>,
> + <&zynqmp_firmware PD_R5_1_ATCM>,
> + <&zynqmp_firmware PD_R5_1_BTCM>;
> memory-region = <&rproc_1_fw_image>;
> };
> };
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc
2024-01-03 17:54 ` Mathieu Poirier
@ 2024-01-03 18:19 ` Tanmay Shah
0 siblings, 0 replies; 13+ messages in thread
From: Tanmay Shah @ 2024-01-03 18:19 UTC (permalink / raw)
To: Mathieu Poirier
Cc: andersson, robh+dt, krzysztof.kozlowski+dt, conor+dt, Simek,
Michal, Levinsky, Ben, linux-remoteproc, devicetree,
linux-arm-kernel, linux-kernel
On 1/3/24 11:54 AM, Mathieu Poirier wrote:
> Hi Tanmay,
>
> On Fri, Dec 15, 2023 at 03:57:24PM -0800, Tanmay Shah wrote:
> > Add properties as per new bindings in zynqmp remoteproc node
> > to represent TCM address and size.
> >
> > This patch also adds alternative remoteproc node to represent
> > remoteproc cluster in split mode. By default lockstep mode is
> > enabled and users should disable it before using split mode
> > dts. Both device-tree nodes can't be used simultaneously one
> > of them must be disabled. For zcu102-1.0 and zcu102-1.1 board
> > remoteproc split mode dts node is enabled and lockstep mode
> > dts is disabled.
> >
> > Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
> > ---
> > .../boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts | 8 +++
> > arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 60 +++++++++++++++++--
> > 2 files changed, 63 insertions(+), 5 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > index c8f71a1aec89..495ca94b45db 100644
> > --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.0.dts
> > @@ -14,6 +14,14 @@ / {
> > compatible = "xlnx,zynqmp-zcu102-rev1.0", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
> > };
> >
> > +&rproc_split {
> > + status = "okay";
> > +};
> > +
> > +&rproc_lockstep {
> > + status = "disabled";
> > +};
> > +
> > &eeprom {
> > #address-cells = <1>;
> > #size-cells = <1>;
> > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > index b61fc99cd911..602e6aba7ac5 100644
> > --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
> > @@ -247,19 +247,69 @@ fpga_full: fpga-full {
> > ranges;
> > };
> >
> > - remoteproc {
> > + rproc_lockstep: remoteproc@ffe00000 {
> > compatible = "xlnx,zynqmp-r5fss";
> > xlnx,cluster-mode = <1>;
> >
> > - r5f-0 {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x20000>,
> > + <0x0 0x20000 0x0 0xffe20000 0x0 0x20000>,
> > + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> > + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
>
> As far as I can tell, in lockstep mode the last two entries are not needed.
> This is also contrasting with that is in the bindings, which is quite confusing.
Hi Mathieu,
Yes I agree. I think it should be same as of bindings example.
However, I will have to test and make sure no impact on driver. I will fix it in next revision.
Meanwhile, are you going to review driver changes as well or do you want to wait for next revision ?
Tanmay
> > +
> > + r5f@0 {
> > + compatible = "xlnx,zynqmp-r5f";
> > + reg = <0x0 0x0 0x0 0x20000>, <0x0 0x20000 0x0 0x20000>;
> > + reg-names = "atcm", "btcm";
> > + power-domains = <&zynqmp_firmware PD_RPU_0>,
> > + <&zynqmp_firmware PD_R5_0_ATCM>,
> > + <&zynqmp_firmware PD_R5_0_BTCM>;
> > + memory-region = <&rproc_0_fw_image>;
> > + };
> > +
> > + r5f@1 {
> > + compatible = "xlnx,zynqmp-r5f";
> > + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> > + reg-names = "atcm", "btcm";
> > + power-domains = <&zynqmp_firmware PD_RPU_1>,
> > + <&zynqmp_firmware PD_R5_1_ATCM>,
> > + <&zynqmp_firmware PD_R5_1_BTCM>;
> > + memory-region = <&rproc_1_fw_image>;
> > + };
> > + };
> > +
> > + rproc_split: remoteproc-split@ffe00000 {
> > + status = "disabled";
> > + compatible = "xlnx,zynqmp-r5fss";
> > + xlnx,cluster-mode = <0>;
> > +
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + ranges = <0x0 0x0 0x0 0xffe00000 0x0 0x10000>,
> > + <0x0 0x20000 0x0 0xffe20000 0x0 0x10000>,
> > + <0x1 0x0 0x0 0xffe90000 0x0 0x10000>,
> > + <0x1 0x20000 0x0 0xffeb0000 0x0 0x10000>;
> > +
> > + r5f@0 {
> > compatible = "xlnx,zynqmp-r5f";
> > - power-domains = <&zynqmp_firmware PD_RPU_0>;
> > + reg = <0x0 0x0 0x0 0x10000>, <0x0 0x20000 0x0 0x10000>;
> > + reg-names = "atcm", "btcm";
> > + power-domains = <&zynqmp_firmware PD_RPU_0>,
> > + <&zynqmp_firmware PD_R5_0_ATCM>,
> > + <&zynqmp_firmware PD_R5_0_BTCM>;
> > memory-region = <&rproc_0_fw_image>;
> > };
> >
> > - r5f-1 {
> > + r5f@1 {
> > compatible = "xlnx,zynqmp-r5f";
> > - power-domains = <&zynqmp_firmware PD_RPU_1>;
> > + reg = <0x1 0x0 0x0 0x10000>, <0x1 0x20000 0x0 0x10000>;
> > + reg-names = "atcm", "btcm";
> > + power-domains = <&zynqmp_firmware PD_RPU_1>,
> > + <&zynqmp_firmware PD_R5_1_ATCM>,
> > + <&zynqmp_firmware PD_R5_1_BTCM>;
> > memory-region = <&rproc_1_fw_image>;
> > };
> > };
> > --
> > 2.25.1
> >
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v8 3/3] remoteproc: zynqmp: parse TCM from device tree
2023-12-15 23:57 [PATCH v8 0/3] add zynqmp TCM bindings Tanmay Shah
2023-12-15 23:57 ` [PATCH v8 1/3] dt-bindings: remoteproc: add Tightly Coupled Memory (TCM) bindings Tanmay Shah
2023-12-15 23:57 ` [PATCH v8 2/3] dts: zynqmp: add properties for TCM in remoteproc Tanmay Shah
@ 2023-12-15 23:57 ` Tanmay Shah
2024-01-03 18:17 ` Mathieu Poirier
2 siblings, 1 reply; 13+ messages in thread
From: Tanmay Shah @ 2023-12-15 23:57 UTC (permalink / raw)
To: andersson, mathieu.poirier, robh+dt, krzysztof.kozlowski+dt,
conor+dt, michal.simek, ben.levinsky, tanmay.shah
Cc: linux-remoteproc, devicetree, linux-arm-kernel, linux-kernel
ZynqMP TCM information is fixed in driver. Now ZynqMP TCM information
is available in device-tree. Parse TCM information in driver
as per new bindings.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
---
Changes in v8:
- parse power-domains property from device-tree and use EEMI calls
to power on/off TCM instead of using pm domains framework
- Remove checking of pm_domain_id validation to power on/off tcm
- Remove spurious change
Changes in v7:
- move checking of pm_domain_id from previous patch
- fix mem_bank_data memory allocation
drivers/remoteproc/xlnx_r5_remoteproc.c | 154 +++++++++++++++++++++++-
1 file changed, 148 insertions(+), 6 deletions(-)
diff --git a/drivers/remoteproc/xlnx_r5_remoteproc.c b/drivers/remoteproc/xlnx_r5_remoteproc.c
index 4395edea9a64..36d73dcd93f0 100644
--- a/drivers/remoteproc/xlnx_r5_remoteproc.c
+++ b/drivers/remoteproc/xlnx_r5_remoteproc.c
@@ -74,8 +74,8 @@ struct mbox_info {
};
/*
- * Hardcoded TCM bank values. This will be removed once TCM bindings are
- * accepted for system-dt specifications and upstreamed in linux kernel
+ * Hardcoded TCM bank values. This will stay in driver to maintain backward
+ * compatibility with device-tree that does not have TCM information.
*/
static const struct mem_bank_data zynqmp_tcm_banks_split[] = {
{0xffe00000UL, 0x0, 0x10000UL, PD_R5_0_ATCM, "atcm0"}, /* TCM 64KB each */
@@ -878,6 +878,139 @@ static struct zynqmp_r5_core *zynqmp_r5_add_rproc_core(struct device *cdev)
return ERR_PTR(ret);
}
+static int zynqmp_r5_get_tcm_node_from_dt(struct zynqmp_r5_cluster *cluster)
+{
+ struct of_phandle_args out_args;
+ int tcm_reg_per_r5, tcm_pd_idx;
+ struct zynqmp_r5_core *r5_core;
+ int i, j, tcm_bank_count, ret;
+ struct platform_device *cpdev;
+ struct mem_bank_data *tcm;
+ struct device_node *np;
+ struct resource *res;
+ u64 abs_addr, size;
+ struct device *dev;
+
+ for (i = 0; i < cluster->core_count; i++) {
+ r5_core = cluster->r5_cores[i];
+ dev = r5_core->dev;
+ np = of_node_get(dev_of_node(dev));
+ tcm_pd_idx = 1;
+
+ /* we have address cell 2 and size cell as 2 */
+ tcm_reg_per_r5 = of_property_count_elems_of_size(np, "reg",
+ 4 * sizeof(u32));
+ if (tcm_reg_per_r5 <= 0) {
+ dev_err(dev, "can't get reg property err %d\n", tcm_reg_per_r5);
+ return -EINVAL;
+ }
+
+ /*
+ * In lockstep mode, r5 core 0 will use r5 core 1 TCM
+ * power domains as well. so allocate twice of per core TCM
+ */
+ if (cluster->mode == LOCKSTEP_MODE)
+ tcm_bank_count = tcm_reg_per_r5 * 2;
+ else
+ tcm_bank_count = tcm_reg_per_r5;
+
+ r5_core->tcm_banks = devm_kcalloc(dev, tcm_bank_count,
+ sizeof(struct mem_bank_data *),
+ GFP_KERNEL);
+ if (!r5_core->tcm_banks)
+ ret = -ENOMEM;
+
+ r5_core->tcm_bank_count = tcm_bank_count;
+ for (j = 0; j < tcm_bank_count; j++) {
+ tcm = devm_kzalloc(dev, sizeof(struct mem_bank_data),
+ GFP_KERNEL);
+ if (!tcm)
+ return -ENOMEM;
+
+ r5_core->tcm_banks[j] = tcm;
+
+ /*
+ * In lockstep mode, get second core's TCM power domains id
+ * after first core TCM parsing is done as
+ */
+ if (j == tcm_reg_per_r5) {
+ /* dec first core node */
+ of_node_put(np);
+
+ /* get second core node */
+ np = of_get_next_child(cluster->dev->of_node, np);
+
+ /*
+ * reset index of power-domains property list
+ * for second core
+ */
+ tcm_pd_idx = 1;
+ }
+
+ /* get power-domains id of tcm */
+ ret = of_parse_phandle_with_args(np, "power-domains",
+ "#power-domain-cells",
+ tcm_pd_idx,
+ &out_args);
+ if (ret) {
+ dev_err(r5_core->dev,
+ "failed to get tcm %d pm domain, ret %d\n",
+ j, ret);
+ of_node_put(out_args.np);
+ return ret;
+ }
+ tcm->pm_domain_id = out_args.args[0];
+ of_node_put(out_args.np);
+ tcm_pd_idx++;
+
+ /*
+ * In lockstep mode, we only need second core's power domain
+ * ids. Other information from second core isn't needed so
+ * ignore it. This forms table as zynqmp_tcm_banks_lockstep
+ */
+ if (j >= tcm_reg_per_r5)
+ continue;
+
+ /* get tcm address without translation */
+ ret = of_property_read_reg(np, j, &abs_addr, &size);
+ if (ret) {
+ of_node_put(np);
+ dev_err(dev, "failed to get reg property\n");
+ return ret;
+ }
+
+ /*
+ * remote processor can address only 32 bits
+ * so convert 64-bits into 32-bits. This will discard
+ * any unwanted upper 32-bits.
+ */
+ tcm->da = (u32)abs_addr;
+ tcm->size = (u32)size;
+
+ cpdev = to_platform_device(dev);
+ res = platform_get_resource(cpdev, IORESOURCE_MEM, j);
+ if (!res) {
+ of_node_put(np);
+ dev_err(dev, "failed to get tcm resource\n");
+ return -EINVAL;
+ }
+
+ tcm->addr = (u32)res->start;
+ tcm->bank_name = (char *)res->name;
+ res = devm_request_mem_region(dev, tcm->addr, tcm->size,
+ tcm->bank_name);
+ if (!res) {
+ dev_err(dev, "failed to request tcm resource\n");
+ of_node_put(np);
+ return -EINVAL;
+ }
+ }
+ }
+
+ of_node_put(np);
+ return 0;
+}
+
/**
* zynqmp_r5_get_tcm_node()
* Ideally this function should parse tcm node and store information
@@ -956,10 +1089,19 @@ static int zynqmp_r5_core_init(struct zynqmp_r5_cluster *cluster,
struct zynqmp_r5_core *r5_core;
int ret, i;
- ret = zynqmp_r5_get_tcm_node(cluster);
- if (ret < 0) {
- dev_err(dev, "can't get tcm node, err %d\n", ret);
- return ret;
+ r5_core = cluster->r5_cores[0];
+ if (of_find_property(r5_core->np, "reg", NULL)) {
+ ret = zynqmp_r5_get_tcm_node_from_dt(cluster);
+ if (ret) {
+ dev_err(dev, "can't get tcm node from dt, err %d\n", ret);
+ return ret;
+ }
+ } else {
+ ret = zynqmp_r5_get_tcm_node(cluster);
+ if (ret < 0) {
+ dev_err(dev, "can't get tcm node, err %d\n", ret);
+ return ret;
+ }
}
for (i = 0; i < cluster->core_count; i++) {
--
2.25.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v8 3/3] remoteproc: zynqmp: parse TCM from device tree
2023-12-15 23:57 ` [PATCH v8 3/3] remoteproc: zynqmp: parse TCM from device tree Tanmay Shah
@ 2024-01-03 18:17 ` Mathieu Poirier
2024-01-03 18:51 ` Tanmay Shah
2024-01-04 16:14 ` Tanmay Shah
0 siblings, 2 replies; 13+ messages in thread
From: Mathieu Poirier @ 2024-01-03 18:17 UTC (permalink / raw)
To: Tanmay Shah
Cc: andersson, robh+dt, krzysztof.kozlowski+dt, conor+dt,
michal.simek, ben.levinsky, linux-remoteproc, devicetree,
linux-arm-kernel, linux-kernel
On Fri, Dec 15, 2023 at 03:57:25PM -0800, Tanmay Shah wrote:
> ZynqMP TCM information is fixed in driver. Now ZynqMP TCM information
s/"is fixed in driver"/"was fixed in driver"
> is available in device-tree. Parse TCM information in driver
> as per new bindings.
>
> Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
> ---
>
> Changes in v8:
> - parse power-domains property from device-tree and use EEMI calls
> to power on/off TCM instead of using pm domains framework
> - Remove checking of pm_domain_id validation to power on/off tcm
> - Remove spurious change
>
> Changes in v7:
> - move checking of pm_domain_id from previous patch
> - fix mem_bank_data memory allocation
>
> drivers/remoteproc/xlnx_r5_remoteproc.c | 154 +++++++++++++++++++++++-
> 1 file changed, 148 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/remoteproc/xlnx_r5_remoteproc.c b/drivers/remoteproc/xlnx_r5_remoteproc.c
> index 4395edea9a64..36d73dcd93f0 100644
> --- a/drivers/remoteproc/xlnx_r5_remoteproc.c
> +++ b/drivers/remoteproc/xlnx_r5_remoteproc.c
> @@ -74,8 +74,8 @@ struct mbox_info {
> };
>
> /*
> - * Hardcoded TCM bank values. This will be removed once TCM bindings are
> - * accepted for system-dt specifications and upstreamed in linux kernel
> + * Hardcoded TCM bank values. This will stay in driver to maintain backward
> + * compatibility with device-tree that does not have TCM information.
> */
> static const struct mem_bank_data zynqmp_tcm_banks_split[] = {
> {0xffe00000UL, 0x0, 0x10000UL, PD_R5_0_ATCM, "atcm0"}, /* TCM 64KB each */
> @@ -878,6 +878,139 @@ static struct zynqmp_r5_core *zynqmp_r5_add_rproc_core(struct device *cdev)
> return ERR_PTR(ret);
> }
>
> +static int zynqmp_r5_get_tcm_node_from_dt(struct zynqmp_r5_cluster *cluster)
> +{
> + struct of_phandle_args out_args;
> + int tcm_reg_per_r5, tcm_pd_idx;
> + struct zynqmp_r5_core *r5_core;
> + int i, j, tcm_bank_count, ret;
> + struct platform_device *cpdev;
> + struct mem_bank_data *tcm;
> + struct device_node *np;
> + struct resource *res;
> + u64 abs_addr, size;
> + struct device *dev;
> +
> + for (i = 0; i < cluster->core_count; i++) {
> + r5_core = cluster->r5_cores[i];
> + dev = r5_core->dev;
> + np = of_node_get(dev_of_node(dev));
> + tcm_pd_idx = 1;
> +
> + /* we have address cell 2 and size cell as 2 */
> + tcm_reg_per_r5 = of_property_count_elems_of_size(np, "reg",
> + 4 * sizeof(u32));
> + if (tcm_reg_per_r5 <= 0) {
> + dev_err(dev, "can't get reg property err %d\n", tcm_reg_per_r5);
> + return -EINVAL;
> + }
> +
> + /*
> + * In lockstep mode, r5 core 0 will use r5 core 1 TCM
> + * power domains as well. so allocate twice of per core TCM
Twice of what? Please use proper english in your multi line comments, i.e a
capital letter for the first word and a dot at the end.
> + */
> + if (cluster->mode == LOCKSTEP_MODE)
> + tcm_bank_count = tcm_reg_per_r5 * 2;
> + else
> + tcm_bank_count = tcm_reg_per_r5;
> +
> + r5_core->tcm_banks = devm_kcalloc(dev, tcm_bank_count,
> + sizeof(struct mem_bank_data *),
> + GFP_KERNEL);
> + if (!r5_core->tcm_banks)
> + ret = -ENOMEM;
> +
> + r5_core->tcm_bank_count = tcm_bank_count;
> + for (j = 0; j < tcm_bank_count; j++) {
> + tcm = devm_kzalloc(dev, sizeof(struct mem_bank_data),
> + GFP_KERNEL);
> + if (!tcm)
> + return -ENOMEM;
> +
> + r5_core->tcm_banks[j] = tcm;
> +
> + /*
> + * In lockstep mode, get second core's TCM power domains id
> + * after first core TCM parsing is done as
There seems to be words missing at the end of the sentence, and there is no dot.
> + */
> + if (j == tcm_reg_per_r5) {
> + /* dec first core node */
> + of_node_put(np);
> +
> + /* get second core node */
> + np = of_get_next_child(cluster->dev->of_node, np);
> +
> + /*
> + * reset index of power-domains property list
> + * for second core
> + */
> + tcm_pd_idx = 1;
> + }
> +
> + /* get power-domains id of tcm */
> + ret = of_parse_phandle_with_args(np, "power-domains",
> + "#power-domain-cells",
> + tcm_pd_idx,
> + &out_args);
> + if (ret) {
> + dev_err(r5_core->dev,
> + "failed to get tcm %d pm domain, ret %d\n",
> + j, ret);
> + of_node_put(out_args.np);
I'm pretty sure this isn't needed in error conditions since @out_args would not
have been assigned.
> + return ret;
> + }
> + tcm->pm_domain_id = out_args.args[0];
> + of_node_put(out_args.np);
> + tcm_pd_idx++;
> +
> + /*
> + * In lockstep mode, we only need second core's power domain
> + * ids. Other information from second core isn't needed so
> + * ignore it. This forms table as zynqmp_tcm_banks_lockstep
I don't understand the last sentence of this comment and it is missing a dot at
the end. Comments should be enlightening, the ones I found in this patch are
sowing confusion.
> + */
> + if (j >= tcm_reg_per_r5)
> + contiue;
> +
This condition and the one above (j == tcm_reg_per_r5) is brittle and almost
guaranteed to cause maintenance problems in the future.
I understand your will to reuse as much code as possible but this is one of the
rare cases where duplicating code is probably better. Please introduce two new
functions, i.e zynqmp_r5_get_tcm_node_from_dt_split() and
zynqmp_r5_get_tcm_node_from_dt_lockstep(), and do all the necessary processing
based on the use case.
Thanks,
Mathieu
> + /* get tcm address without translation */
> + ret = of_property_read_reg(np, j, &abs_addr, &size);
> + if (ret) {
> + of_node_put(np);
> + dev_err(dev, "failed to get reg property\n");
> + return ret;
> + }
> +
> + /*
> + * remote processor can address only 32 bits
> + * so convert 64-bits into 32-bits. This will discard
> + * any unwanted upper 32-bits.
> + */
> + tcm->da = (u32)abs_addr;
> + tcm->size = (u32)size;
> +
> + cpdev = to_platform_device(dev);
> + res = platform_get_resource(cpdev, IORESOURCE_MEM, j);
> + if (!res) {
> + of_node_put(np);
> + dev_err(dev, "failed to get tcm resource\n");
> + return -EINVAL;
> + }
> +
> + tcm->addr = (u32)res->start;
> + tcm->bank_name = (char *)res->name;
> + res = devm_request_mem_region(dev, tcm->addr, tcm->size,
> + tcm->bank_name);
> + if (!res) {
> + dev_err(dev, "failed to request tcm resource\n");
> + of_node_put(np);
> + return -EINVAL;
> + }
> + }
> + }
> +
> + of_node_put(np);
> + return 0;
> +}
> +
> /**
> * zynqmp_r5_get_tcm_node()
> * Ideally this function should parse tcm node and store information
> @@ -956,10 +1089,19 @@ static int zynqmp_r5_core_init(struct zynqmp_r5_cluster *cluster,
> struct zynqmp_r5_core *r5_core;
> int ret, i;
>
> - ret = zynqmp_r5_get_tcm_node(cluster);
> - if (ret < 0) {
> - dev_err(dev, "can't get tcm node, err %d\n", ret);
> - return ret;
> + r5_core = cluster->r5_cores[0];
> + if (of_find_property(r5_core->np, "reg", NULL)) {
> + ret = zynqmp_r5_get_tcm_node_from_dt(cluster);
> + if (ret) {
> + dev_err(dev, "can't get tcm node from dt, err %d\n", ret);
> + return ret;
> + }
> + } else {
> + ret = zynqmp_r5_get_tcm_node(cluster);
> + if (ret < 0) {
> + dev_err(dev, "can't get tcm node, err %d\n", ret);
> + return ret;
> + }
> }
>
> for (i = 0; i < cluster->core_count; i++) {
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v8 3/3] remoteproc: zynqmp: parse TCM from device tree
2024-01-03 18:17 ` Mathieu Poirier
@ 2024-01-03 18:51 ` Tanmay Shah
2024-01-04 16:14 ` Tanmay Shah
1 sibling, 0 replies; 13+ messages in thread
From: Tanmay Shah @ 2024-01-03 18:51 UTC (permalink / raw)
To: Mathieu Poirier
Cc: andersson, robh+dt, krzysztof.kozlowski+dt, conor+dt,
michal.simek, ben.levinsky, linux-remoteproc, devicetree,
linux-arm-kernel, linux-kernel
On 1/3/24 12:17 PM, Mathieu Poirier wrote:
> On Fri, Dec 15, 2023 at 03:57:25PM -0800, Tanmay Shah wrote:
> > ZynqMP TCM information is fixed in driver. Now ZynqMP TCM information
>
> s/"is fixed in driver"/"was fixed in driver"
>
> > is available in device-tree. Parse TCM information in driver
> > as per new bindings.
> >
> > Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
> > ---
> >
> > Changes in v8:
> > - parse power-domains property from device-tree and use EEMI calls
> > to power on/off TCM instead of using pm domains framework
> > - Remove checking of pm_domain_id validation to power on/off tcm
> > - Remove spurious change
> >
> > Changes in v7:
> > - move checking of pm_domain_id from previous patch
> > - fix mem_bank_data memory allocation
> >
> > drivers/remoteproc/xlnx_r5_remoteproc.c | 154 +++++++++++++++++++++++-
> > 1 file changed, 148 insertions(+), 6 deletions(-)
> >
> > diff --git a/drivers/remoteproc/xlnx_r5_remoteproc.c b/drivers/remoteproc/xlnx_r5_remoteproc.c
> > index 4395edea9a64..36d73dcd93f0 100644
> > --- a/drivers/remoteproc/xlnx_r5_remoteproc.c
> > +++ b/drivers/remoteproc/xlnx_r5_remoteproc.c
> > @@ -74,8 +74,8 @@ struct mbox_info {
> > };
> >
> > /*
> > - * Hardcoded TCM bank values. This will be removed once TCM bindings are
> > - * accepted for system-dt specifications and upstreamed in linux kernel
> > + * Hardcoded TCM bank values. This will stay in driver to maintain backward
> > + * compatibility with device-tree that does not have TCM information.
> > */
> > static const struct mem_bank_data zynqmp_tcm_banks_split[] = {
> > {0xffe00000UL, 0x0, 0x10000UL, PD_R5_0_ATCM, "atcm0"}, /* TCM 64KB each */
> > @@ -878,6 +878,139 @@ static struct zynqmp_r5_core *zynqmp_r5_add_rproc_core(struct device *cdev)
> > return ERR_PTR(ret);
> > }
> >
> > +static int zynqmp_r5_get_tcm_node_from_dt(struct zynqmp_r5_cluster *cluster)
> > +{
> > + struct of_phandle_args out_args;
> > + int tcm_reg_per_r5, tcm_pd_idx;
> > + struct zynqmp_r5_core *r5_core;
> > + int i, j, tcm_bank_count, ret;
> > + struct platform_device *cpdev;
> > + struct mem_bank_data *tcm;
> > + struct device_node *np;
> > + struct resource *res;
> > + u64 abs_addr, size;
> > + struct device *dev;
> > +
> > + for (i = 0; i < cluster->core_count; i++) {
> > + r5_core = cluster->r5_cores[i];
> > + dev = r5_core->dev;
> > + np = of_node_get(dev_of_node(dev));
> > + tcm_pd_idx = 1;
> > +
> > + /* we have address cell 2 and size cell as 2 */
> > + tcm_reg_per_r5 = of_property_count_elems_of_size(np, "reg",
> > + 4 * sizeof(u32));
> > + if (tcm_reg_per_r5 <= 0) {
> > + dev_err(dev, "can't get reg property err %d\n", tcm_reg_per_r5);
> > + return -EINVAL;
> > + }
> > +
> > + /*
> > + * In lockstep mode, r5 core 0 will use r5 core 1 TCM
> > + * power domains as well. so allocate twice of per core TCM
>
> Twice of what? Please use proper english in your multi line comments, i.e a
> capital letter for the first word and a dot at the end.
>
> > + */
> > + if (cluster->mode == LOCKSTEP_MODE)
> > + tcm_bank_count = tcm_reg_per_r5 * 2;
> > + else
> > + tcm_bank_count = tcm_reg_per_r5;
> > +
> > + r5_core->tcm_banks = devm_kcalloc(dev, tcm_bank_count,
> > + sizeof(struct mem_bank_data *),
> > + GFP_KERNEL);
> > + if (!r5_core->tcm_banks)
> > + ret = -ENOMEM;
> > +
> > + r5_core->tcm_bank_count = tcm_bank_count;
> > + for (j = 0; j < tcm_bank_count; j++) {
> > + tcm = devm_kzalloc(dev, sizeof(struct mem_bank_data),
> > + GFP_KERNEL);
> > + if (!tcm)
> > + return -ENOMEM;
> > +
> > + r5_core->tcm_banks[j] = tcm;
> > +
> > + /*
> > + * In lockstep mode, get second core's TCM power domains id
> > + * after first core TCM parsing is done as
>
> There seems to be words missing at the end of the sentence, and there is no dot.
>
> > + */
> > + if (j == tcm_reg_per_r5) {
> > + /* dec first core node */
> > + of_node_put(np);
> > +
> > + /* get second core node */
> > + np = of_get_next_child(cluster->dev->of_node, np);
> > +
> > + /*
> > + * reset index of power-domains property list
> > + * for second core
> > + */
> > + tcm_pd_idx = 1;
> > + }
> > +
> > + /* get power-domains id of tcm */
> > + ret = of_parse_phandle_with_args(np, "power-domains",
> > + "#power-domain-cells",
> > + tcm_pd_idx,
> > + &out_args);
> > + if (ret) {
> > + dev_err(r5_core->dev,
> > + "failed to get tcm %d pm domain, ret %d\n",
> > + j, ret);
> > + of_node_put(out_args.np);
>
> I'm pretty sure this isn't needed in error conditions since @out_args would not
> have been assigned.
>
> > + return ret;
> > + }
> > + tcm->pm_domain_id = out_args.args[0];
> > + of_node_put(out_args.np);
> > + tcm_pd_idx++;
> > +
> > + /*
> > + * In lockstep mode, we only need second core's power domain
> > + * ids. Other information from second core isn't needed so
> > + * ignore it. This forms table as zynqmp_tcm_banks_lockstep
>
> I don't understand the last sentence of this comment and it is missing a dot at
> the end. Comments should be enlightening, the ones I found in this patch are
> sowing confusion.
>
> > + */
> > + if (j >= tcm_reg_per_r5)
> > + contiue;
> > +
>
> This condition and the one above (j == tcm_reg_per_r5) is brittle and almost
> guaranteed to cause maintenance problems in the future.
>
> I understand your will to reuse as much code as possible but this is one of the
> rare cases where duplicating code is probably better. Please introduce two new
> functions, i.e zynqmp_r5_get_tcm_node_from_dt_split() and
> zynqmp_r5_get_tcm_node_from_dt_lockstep(), and do all the necessary processing
> based on the use case.
Ack will fix the documentation and tcm parsing as suggested.
> Thanks,
> Mathieu
>
> > + /* get tcm address without translation */
> > + ret = of_property_read_reg(np, j, &abs_addr, &size);
> > + if (ret) {
> > + of_node_put(np);
> > + dev_err(dev, "failed to get reg property\n");
> > + return ret;
> > + }
> > +
> > + /*
> > + * remote processor can address only 32 bits
> > + * so convert 64-bits into 32-bits. This will discard
> > + * any unwanted upper 32-bits.
> > + */
> > + tcm->da = (u32)abs_addr;
> > + tcm->size = (u32)size;
> > +
> > + cpdev = to_platform_device(dev);
> > + res = platform_get_resource(cpdev, IORESOURCE_MEM, j);
> > + if (!res) {
> > + of_node_put(np);
> > + dev_err(dev, "failed to get tcm resource\n");
> > + return -EINVAL;
> > + }
> > +
> > + tcm->addr = (u32)res->start;
> > + tcm->bank_name = (char *)res->name;
> > + res = devm_request_mem_region(dev, tcm->addr, tcm->size,
> > + tcm->bank_name);
> > + if (!res) {
> > + dev_err(dev, "failed to request tcm resource\n");
> > + of_node_put(np);
> > + return -EINVAL;
> > + }
> > + }
> > + }
> > +
> > + of_node_put(np);
> > + return 0;
> > +}
> > +
> > /**
> > * zynqmp_r5_get_tcm_node()
> > * Ideally this function should parse tcm node and store information
> > @@ -956,10 +1089,19 @@ static int zynqmp_r5_core_init(struct zynqmp_r5_cluster *cluster,
> > struct zynqmp_r5_core *r5_core;
> > int ret, i;
> >
> > - ret = zynqmp_r5_get_tcm_node(cluster);
> > - if (ret < 0) {
> > - dev_err(dev, "can't get tcm node, err %d\n", ret);
> > - return ret;
> > + r5_core = cluster->r5_cores[0];
> > + if (of_find_property(r5_core->np, "reg", NULL)) {
> > + ret = zynqmp_r5_get_tcm_node_from_dt(cluster);
> > + if (ret) {
> > + dev_err(dev, "can't get tcm node from dt, err %d\n", ret);
> > + return ret;
> > + }
> > + } else {
> > + ret = zynqmp_r5_get_tcm_node(cluster);
> > + if (ret < 0) {
> > + dev_err(dev, "can't get tcm node, err %d\n", ret);
> > + return ret;
> > + }
> > }
> >
> > for (i = 0; i < cluster->core_count; i++) {
> > --
> > 2.25.1
> >
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v8 3/3] remoteproc: zynqmp: parse TCM from device tree
2024-01-03 18:17 ` Mathieu Poirier
2024-01-03 18:51 ` Tanmay Shah
@ 2024-01-04 16:14 ` Tanmay Shah
2024-01-08 17:25 ` Mathieu Poirier
1 sibling, 1 reply; 13+ messages in thread
From: Tanmay Shah @ 2024-01-04 16:14 UTC (permalink / raw)
To: Mathieu Poirier
Cc: andersson, robh+dt, krzysztof.kozlowski+dt, conor+dt,
michal.simek, ben.levinsky, linux-remoteproc, devicetree,
linux-arm-kernel, linux-kernel
On 1/3/24 12:17 PM, Mathieu Poirier wrote:
> On Fri, Dec 15, 2023 at 03:57:25PM -0800, Tanmay Shah wrote:
> > ZynqMP TCM information is fixed in driver. Now ZynqMP TCM information
>
> s/"is fixed in driver"/"was fixed in driver"
>
> > is available in device-tree. Parse TCM information in driver
> > as per new bindings.
> >
> > Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
> > ---
> >
> > Changes in v8:
> > - parse power-domains property from device-tree and use EEMI calls
> > to power on/off TCM instead of using pm domains framework
> > - Remove checking of pm_domain_id validation to power on/off tcm
> > - Remove spurious change
> >
> > Changes in v7:
> > - move checking of pm_domain_id from previous patch
> > - fix mem_bank_data memory allocation
> >
> > drivers/remoteproc/xlnx_r5_remoteproc.c | 154 +++++++++++++++++++++++-
> > 1 file changed, 148 insertions(+), 6 deletions(-)
> >
> > diff --git a/drivers/remoteproc/xlnx_r5_remoteproc.c b/drivers/remoteproc/xlnx_r5_remoteproc.c
> > index 4395edea9a64..36d73dcd93f0 100644
> > --- a/drivers/remoteproc/xlnx_r5_remoteproc.c
> > +++ b/drivers/remoteproc/xlnx_r5_remoteproc.c
> > @@ -74,8 +74,8 @@ struct mbox_info {
> > };
> >
> > /*
> > - * Hardcoded TCM bank values. This will be removed once TCM bindings are
> > - * accepted for system-dt specifications and upstreamed in linux kernel
> > + * Hardcoded TCM bank values. This will stay in driver to maintain backward
> > + * compatibility with device-tree that does not have TCM information.
> > */
> > static const struct mem_bank_data zynqmp_tcm_banks_split[] = {
> > {0xffe00000UL, 0x0, 0x10000UL, PD_R5_0_ATCM, "atcm0"}, /* TCM 64KB each */
> > @@ -878,6 +878,139 @@ static struct zynqmp_r5_core *zynqmp_r5_add_rproc_core(struct device *cdev)
> > return ERR_PTR(ret);
> > }
> >
> > +static int zynqmp_r5_get_tcm_node_from_dt(struct zynqmp_r5_cluster *cluster)
> > +{
> > + struct of_phandle_args out_args;
> > + int tcm_reg_per_r5, tcm_pd_idx;
> > + struct zynqmp_r5_core *r5_core;
> > + int i, j, tcm_bank_count, ret;
> > + struct platform_device *cpdev;
> > + struct mem_bank_data *tcm;
> > + struct device_node *np;
> > + struct resource *res;
> > + u64 abs_addr, size;
> > + struct device *dev;
> > +
> > + for (i = 0; i < cluster->core_count; i++) {
> > + r5_core = cluster->r5_cores[i];
> > + dev = r5_core->dev;
> > + np = of_node_get(dev_of_node(dev));
> > + tcm_pd_idx = 1;
> > +
> > + /* we have address cell 2 and size cell as 2 */
> > + tcm_reg_per_r5 = of_property_count_elems_of_size(np, "reg",
> > + 4 * sizeof(u32));
> > + if (tcm_reg_per_r5 <= 0) {
> > + dev_err(dev, "can't get reg property err %d\n", tcm_reg_per_r5);
> > + return -EINVAL;
> > + }
> > +
> > + /*
> > + * In lockstep mode, r5 core 0 will use r5 core 1 TCM
> > + * power domains as well. so allocate twice of per core TCM
>
> Twice of what? Please use proper english in your multi line comments, i.e a
> capital letter for the first word and a dot at the end.
>
> > + */
> > + if (cluster->mode == LOCKSTEP_MODE)
> > + tcm_bank_count = tcm_reg_per_r5 * 2;
> > + else
> > + tcm_bank_count = tcm_reg_per_r5;
> > +
> > + r5_core->tcm_banks = devm_kcalloc(dev, tcm_bank_count,
> > + sizeof(struct mem_bank_data *),
> > + GFP_KERNEL);
> > + if (!r5_core->tcm_banks)
> > + ret = -ENOMEM;
> > +
> > + r5_core->tcm_bank_count = tcm_bank_count;
> > + for (j = 0; j < tcm_bank_count; j++) {
> > + tcm = devm_kzalloc(dev, sizeof(struct mem_bank_data),
> > + GFP_KERNEL);
> > + if (!tcm)
> > + return -ENOMEM;
> > +
> > + r5_core->tcm_banks[j] = tcm;
> > +
> > + /*
> > + * In lockstep mode, get second core's TCM power domains id
> > + * after first core TCM parsing is done as
>
> There seems to be words missing at the end of the sentence, and there is no dot.
>
> > + */
> > + if (j == tcm_reg_per_r5) {
> > + /* dec first core node */
> > + of_node_put(np);
> > +
> > + /* get second core node */
> > + np = of_get_next_child(cluster->dev->of_node, np);
> > +
> > + /*
> > + * reset index of power-domains property list
> > + * for second core
> > + */
> > + tcm_pd_idx = 1;
> > + }
> > +
> > + /* get power-domains id of tcm */
> > + ret = of_parse_phandle_with_args(np, "power-domains",
> > + "#power-domain-cells",
> > + tcm_pd_idx,
> > + &out_args);
> > + if (ret) {
> > + dev_err(r5_core->dev,
> > + "failed to get tcm %d pm domain, ret %d\n",
> > + j, ret);
> > + of_node_put(out_args.np);
>
> I'm pretty sure this isn't needed in error conditions since @out_args would not
> have been assigned.
>
> > + return ret;
> > + }
> > + tcm->pm_domain_id = out_args.args[0];
> > + of_node_put(out_args.np);
> > + tcm_pd_idx++;
> > +
> > + /*
> > + * In lockstep mode, we only need second core's power domain
> > + * ids. Other information from second core isn't needed so
> > + * ignore it. This forms table as zynqmp_tcm_banks_lockstep
>
> I don't understand the last sentence of this comment and it is missing a dot at
> the end. Comments should be enlightening, the ones I found in this patch are
> sowing confusion.
>
> > + */
> > + if (j >= tcm_reg_per_r5)
> > + contiue;
> > +
>
> This condition and the one above (j == tcm_reg_per_r5) is brittle and almost
> guaranteed to cause maintenance problems in the future.
>
> I understand your will to reuse as much code as possible but this is one of the
> rare cases where duplicating code is probably better. Please introduce two new
> functions, i.e zynqmp_r5_get_tcm_node_from_dt_split() and
> zynqmp_r5_get_tcm_node_from_dt_lockstep(), and do all the necessary processing
> based on the use case.
Hi Mathieu,
I tried to implement this and it still looks hacky, as in lockstep mode unnecessary TCM is being allocated just to store power-domains.
Instead, I am taking another cleaner approach where, TCM is parsed in uniform way in both modes from device-tree during
zynqmp_r5_core_init. However, during "add_tcm_carveout_lockstep_mode" call, I will simply parse second core's TCM power-domains
from device-tree and turn it on.
I will implement this and send v9 after successful testing. I wanted to give you heads up on this approach. I hope it is fine.
Thanks,
Tanmay
>
> Thanks,
> Mathieu
>
> > + /* get tcm address without translation */
> > + ret = of_property_read_reg(np, j, &abs_addr, &size);
> > + if (ret) {
> > + of_node_put(np);
> > + dev_err(dev, "failed to get reg property\n");
> > + return ret;
> > + }
> > +
> > + /*
> > + * remote processor can address only 32 bits
> > + * so convert 64-bits into 32-bits. This will discard
> > + * any unwanted upper 32-bits.
> > + */
> > + tcm->da = (u32)abs_addr;
> > + tcm->size = (u32)size;
> > +
> > + cpdev = to_platform_device(dev);
> > + res = platform_get_resource(cpdev, IORESOURCE_MEM, j);
> > + if (!res) {
> > + of_node_put(np);
> > + dev_err(dev, "failed to get tcm resource\n");
> > + return -EINVAL;
> > + }
> > +
> > + tcm->addr = (u32)res->start;
> > + tcm->bank_name = (char *)res->name;
> > + res = devm_request_mem_region(dev, tcm->addr, tcm->size,
> > + tcm->bank_name);
> > + if (!res) {
> > + dev_err(dev, "failed to request tcm resource\n");
> > + of_node_put(np);
> > + return -EINVAL;
> > + }
> > + }
> > + }
> > +
> > + of_node_put(np);
> > + return 0;
> > +}
> > +
> > /**
> > * zynqmp_r5_get_tcm_node()
> > * Ideally this function should parse tcm node and store information
> > @@ -956,10 +1089,19 @@ static int zynqmp_r5_core_init(struct zynqmp_r5_cluster *cluster,
> > struct zynqmp_r5_core *r5_core;
> > int ret, i;
> >
> > - ret = zynqmp_r5_get_tcm_node(cluster);
> > - if (ret < 0) {
> > - dev_err(dev, "can't get tcm node, err %d\n", ret);
> > - return ret;
> > + r5_core = cluster->r5_cores[0];
> > + if (of_find_property(r5_core->np, "reg", NULL)) {
> > + ret = zynqmp_r5_get_tcm_node_from_dt(cluster);
> > + if (ret) {
> > + dev_err(dev, "can't get tcm node from dt, err %d\n", ret);
> > + return ret;
> > + }
> > + } else {
> > + ret = zynqmp_r5_get_tcm_node(cluster);
> > + if (ret < 0) {
> > + dev_err(dev, "can't get tcm node, err %d\n", ret);
> > + return ret;
> > + }
> > }
> >
> > for (i = 0; i < cluster->core_count; i++) {
> > --
> > 2.25.1
> >
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v8 3/3] remoteproc: zynqmp: parse TCM from device tree
2024-01-04 16:14 ` Tanmay Shah
@ 2024-01-08 17:25 ` Mathieu Poirier
0 siblings, 0 replies; 13+ messages in thread
From: Mathieu Poirier @ 2024-01-08 17:25 UTC (permalink / raw)
To: Tanmay Shah
Cc: andersson, robh+dt, krzysztof.kozlowski+dt, conor+dt,
michal.simek, ben.levinsky, linux-remoteproc, devicetree,
linux-arm-kernel, linux-kernel
On Thu, 4 Jan 2024 at 09:14, Tanmay Shah <tanmay.shah@amd.com> wrote:
>
>
> On 1/3/24 12:17 PM, Mathieu Poirier wrote:
> > On Fri, Dec 15, 2023 at 03:57:25PM -0800, Tanmay Shah wrote:
> > > ZynqMP TCM information is fixed in driver. Now ZynqMP TCM information
> >
> > s/"is fixed in driver"/"was fixed in driver"
> >
> > > is available in device-tree. Parse TCM information in driver
> > > as per new bindings.
> > >
> > > Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
> > > ---
> > >
> > > Changes in v8:
> > > - parse power-domains property from device-tree and use EEMI calls
> > > to power on/off TCM instead of using pm domains framework
> > > - Remove checking of pm_domain_id validation to power on/off tcm
> > > - Remove spurious change
> > >
> > > Changes in v7:
> > > - move checking of pm_domain_id from previous patch
> > > - fix mem_bank_data memory allocation
> > >
> > > drivers/remoteproc/xlnx_r5_remoteproc.c | 154 +++++++++++++++++++++++-
> > > 1 file changed, 148 insertions(+), 6 deletions(-)
> > >
> > > diff --git a/drivers/remoteproc/xlnx_r5_remoteproc.c b/drivers/remoteproc/xlnx_r5_remoteproc.c
> > > index 4395edea9a64..36d73dcd93f0 100644
> > > --- a/drivers/remoteproc/xlnx_r5_remoteproc.c
> > > +++ b/drivers/remoteproc/xlnx_r5_remoteproc.c
> > > @@ -74,8 +74,8 @@ struct mbox_info {
> > > };
> > >
> > > /*
> > > - * Hardcoded TCM bank values. This will be removed once TCM bindings are
> > > - * accepted for system-dt specifications and upstreamed in linux kernel
> > > + * Hardcoded TCM bank values. This will stay in driver to maintain backward
> > > + * compatibility with device-tree that does not have TCM information.
> > > */
> > > static const struct mem_bank_data zynqmp_tcm_banks_split[] = {
> > > {0xffe00000UL, 0x0, 0x10000UL, PD_R5_0_ATCM, "atcm0"}, /* TCM 64KB each */
> > > @@ -878,6 +878,139 @@ static struct zynqmp_r5_core *zynqmp_r5_add_rproc_core(struct device *cdev)
> > > return ERR_PTR(ret);
> > > }
> > >
> > > +static int zynqmp_r5_get_tcm_node_from_dt(struct zynqmp_r5_cluster *cluster)
> > > +{
> > > + struct of_phandle_args out_args;
> > > + int tcm_reg_per_r5, tcm_pd_idx;
> > > + struct zynqmp_r5_core *r5_core;
> > > + int i, j, tcm_bank_count, ret;
> > > + struct platform_device *cpdev;
> > > + struct mem_bank_data *tcm;
> > > + struct device_node *np;
> > > + struct resource *res;
> > > + u64 abs_addr, size;
> > > + struct device *dev;
> > > +
> > > + for (i = 0; i < cluster->core_count; i++) {
> > > + r5_core = cluster->r5_cores[i];
> > > + dev = r5_core->dev;
> > > + np = of_node_get(dev_of_node(dev));
> > > + tcm_pd_idx = 1;
> > > +
> > > + /* we have address cell 2 and size cell as 2 */
> > > + tcm_reg_per_r5 = of_property_count_elems_of_size(np, "reg",
> > > + 4 * sizeof(u32));
> > > + if (tcm_reg_per_r5 <= 0) {
> > > + dev_err(dev, "can't get reg property err %d\n", tcm_reg_per_r5);
> > > + return -EINVAL;
> > > + }
> > > +
> > > + /*
> > > + * In lockstep mode, r5 core 0 will use r5 core 1 TCM
> > > + * power domains as well. so allocate twice of per core TCM
> >
> > Twice of what? Please use proper english in your multi line comments, i.e a
> > capital letter for the first word and a dot at the end.
> >
> > > + */
> > > + if (cluster->mode == LOCKSTEP_MODE)
> > > + tcm_bank_count = tcm_reg_per_r5 * 2;
> > > + else
> > > + tcm_bank_count = tcm_reg_per_r5;
> > > +
> > > + r5_core->tcm_banks = devm_kcalloc(dev, tcm_bank_count,
> > > + sizeof(struct mem_bank_data *),
> > > + GFP_KERNEL);
> > > + if (!r5_core->tcm_banks)
> > > + ret = -ENOMEM;
> > > +
> > > + r5_core->tcm_bank_count = tcm_bank_count;
> > > + for (j = 0; j < tcm_bank_count; j++) {
> > > + tcm = devm_kzalloc(dev, sizeof(struct mem_bank_data),
> > > + GFP_KERNEL);
> > > + if (!tcm)
> > > + return -ENOMEM;
> > > +
> > > + r5_core->tcm_banks[j] = tcm;
> > > +
> > > + /*
> > > + * In lockstep mode, get second core's TCM power domains id
> > > + * after first core TCM parsing is done as
> >
> > There seems to be words missing at the end of the sentence, and there is no dot.
> >
> > > + */
> > > + if (j == tcm_reg_per_r5) {
> > > + /* dec first core node */
> > > + of_node_put(np);
> > > +
> > > + /* get second core node */
> > > + np = of_get_next_child(cluster->dev->of_node, np);
> > > +
> > > + /*
> > > + * reset index of power-domains property list
> > > + * for second core
> > > + */
> > > + tcm_pd_idx = 1;
> > > + }
> > > +
> > > + /* get power-domains id of tcm */
> > > + ret = of_parse_phandle_with_args(np, "power-domains",
> > > + "#power-domain-cells",
> > > + tcm_pd_idx,
> > > + &out_args);
> > > + if (ret) {
> > > + dev_err(r5_core->dev,
> > > + "failed to get tcm %d pm domain, ret %d\n",
> > > + j, ret);
> > > + of_node_put(out_args.np);
> >
> > I'm pretty sure this isn't needed in error conditions since @out_args would not
> > have been assigned.
> >
> > > + return ret;
> > > + }
> > > + tcm->pm_domain_id = out_args.args[0];
> > > + of_node_put(out_args.np);
> > > + tcm_pd_idx++;
> > > +
> > > + /*
> > > + * In lockstep mode, we only need second core's power domain
> > > + * ids. Other information from second core isn't needed so
> > > + * ignore it. This forms table as zynqmp_tcm_banks_lockstep
> >
> > I don't understand the last sentence of this comment and it is missing a dot at
> > the end. Comments should be enlightening, the ones I found in this patch are
> > sowing confusion.
> >
> > > + */
> > > + if (j >= tcm_reg_per_r5)
> > > + contiue;
> > > +
> >
> > This condition and the one above (j == tcm_reg_per_r5) is brittle and almost
> > guaranteed to cause maintenance problems in the future.
> >
> > I understand your will to reuse as much code as possible but this is one of the
> > rare cases where duplicating code is probably better. Please introduce two new
> > functions, i.e zynqmp_r5_get_tcm_node_from_dt_split() and
> > zynqmp_r5_get_tcm_node_from_dt_lockstep(), and do all the necessary processing
> > based on the use case.
>
> Hi Mathieu,
>
> I tried to implement this and it still looks hacky, as in lockstep mode unnecessary TCM is being allocated just to store power-domains.
>
> Instead, I am taking another cleaner approach where, TCM is parsed in uniform way in both modes from device-tree during
>
> zynqmp_r5_core_init. However, during "add_tcm_carveout_lockstep_mode" call, I will simply parse second core's TCM power-domains
>
> from device-tree and turn it on.
>
> I will implement this and send v9 after successful testing. I wanted to give you heads up on this approach. I hope it is fine.
>
Thanks for letting me know - now I don't have to pull out what's left
of hair on my head to figure out what is going on.
> Thanks,
> Tanmay
>
>
> >
> > Thanks,
> > Mathieu
> >
> > > + /* get tcm address without translation */
> > > + ret = of_property_read_reg(np, j, &abs_addr, &size);
> > > + if (ret) {
> > > + of_node_put(np);
> > > + dev_err(dev, "failed to get reg property\n");
> > > + return ret;
> > > + }
> > > +
> > > + /*
> > > + * remote processor can address only 32 bits
> > > + * so convert 64-bits into 32-bits. This will discard
> > > + * any unwanted upper 32-bits.
> > > + */
> > > + tcm->da = (u32)abs_addr;
> > > + tcm->size = (u32)size;
> > > +
> > > + cpdev = to_platform_device(dev);
> > > + res = platform_get_resource(cpdev, IORESOURCE_MEM, j);
> > > + if (!res) {
> > > + of_node_put(np);
> > > + dev_err(dev, "failed to get tcm resource\n");
> > > + return -EINVAL;
> > > + }
> > > +
> > > + tcm->addr = (u32)res->start;
> > > + tcm->bank_name = (char *)res->name;
> > > + res = devm_request_mem_region(dev, tcm->addr, tcm->size,
> > > + tcm->bank_name);
> > > + if (!res) {
> > > + dev_err(dev, "failed to request tcm resource\n");
> > > + of_node_put(np);
> > > + return -EINVAL;
> > > + }
> > > + }
> > > + }
> > > +
> > > + of_node_put(np);
> > > + return 0;
> > > +}
> > > +
> > > /**
> > > * zynqmp_r5_get_tcm_node()
> > > * Ideally this function should parse tcm node and store information
> > > @@ -956,10 +1089,19 @@ static int zynqmp_r5_core_init(struct zynqmp_r5_cluster *cluster,
> > > struct zynqmp_r5_core *r5_core;
> > > int ret, i;
> > >
> > > - ret = zynqmp_r5_get_tcm_node(cluster);
> > > - if (ret < 0) {
> > > - dev_err(dev, "can't get tcm node, err %d\n", ret);
> > > - return ret;
> > > + r5_core = cluster->r5_cores[0];
> > > + if (of_find_property(r5_core->np, "reg", NULL)) {
> > > + ret = zynqmp_r5_get_tcm_node_from_dt(cluster);
> > > + if (ret) {
> > > + dev_err(dev, "can't get tcm node from dt, err %d\n", ret);
> > > + return ret;
> > > + }
> > > + } else {
> > > + ret = zynqmp_r5_get_tcm_node(cluster);
> > > + if (ret < 0) {
> > > + dev_err(dev, "can't get tcm node, err %d\n", ret);
> > > + return ret;
> > > + }
> > > }
> > >
> > > for (i = 0; i < cluster->core_count; i++) {
> > > --
> > > 2.25.1
> > >
^ permalink raw reply [flat|nested] 13+ messages in thread