* [PATCH v3 1/4] ARM: dts: imx: Add GW5907 board support
2019-12-23 21:44 [PATCH v3 0/4] ARM: dts: imx: Add GW59xx Gateworks specials Robert Jones
@ 2019-12-23 21:44 ` Robert Jones
2019-12-23 22:05 ` Fabio Estevam
2019-12-23 21:44 ` [PATCH v3 2/4] ARM: dts: imx: Add GW5910 " Robert Jones
` (2 subsequent siblings)
3 siblings, 1 reply; 9+ messages in thread
From: Robert Jones @ 2019-12-23 21:44 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer
Cc: Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel, linux-arm-kernel, Robert Jones,
Tim Harvey
The Gateworks GW5907 is an IMX6 SoC based single board computer with:
- IMX6Q or IMX6DL
- 32bit DDR3 DRAM
- FEC GbE Phy
- bi-color front-panel LED
- 256MB NAND boot device
- Gateworks System Controller (hwmon, pushbutton controller, EEPROM)
- Digital IO expander (pca9555)
- Joystick 12bit adc (ads1015)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Robert Jones <rjones@gateworks.com>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-gw5907.dts | 14 ++
arch/arm/boot/dts/imx6q-gw5907.dts | 14 ++
arch/arm/boot/dts/imx6qdl-gw5907.dtsi | 399 ++++++++++++++++++++++++++++++++++
4 files changed, 429 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-gw5907.dts
create mode 100644 arch/arm/boot/dts/imx6q-gw5907.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-gw5907.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 1e9e1af..9ee80e2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -422,6 +422,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-gw560x.dtb \
imx6dl-gw5903.dtb \
imx6dl-gw5904.dtb \
+ imx6dl-gw5907.dtb \
imx6dl-hummingboard.dtb \
imx6dl-hummingboard-emmc-som-v15.dtb \
imx6dl-hummingboard-som-v15.dtb \
@@ -493,6 +494,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-gw560x.dtb \
imx6q-gw5903.dtb \
imx6q-gw5904.dtb \
+ imx6q-gw5907.dtb \
imx6q-h100.dtb \
imx6q-hummingboard.dtb \
imx6q-hummingboard-emmc-som-v15.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-gw5907.dts b/arch/arm/boot/dts/imx6dl-gw5907.dts
new file mode 100644
index 0000000..7d9fe47
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-gw5907.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw5907.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 DualLite/Solo GW5907";
+ compatible = "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6q-gw5907.dts b/arch/arm/boot/dts/imx6q-gw5907.dts
new file mode 100644
index 0000000..63e0bef
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-gw5907.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-gw5907.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 Dual/Quad GW5907";
+ compatible = "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-gw5907.dtsi b/arch/arm/boot/dts/imx6qdl-gw5907.dtsi
new file mode 100644
index 0000000..0bdebdd
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-gw5907.dtsi
@@ -0,0 +1,399 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ /* these are used by bootloader for disabling nodes */
+ aliases {
+ led0 = &led0;
+ led1 = &led1;
+ nand = &gpmi;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led0: user1 {
+ label = "user1";
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led1: user2 {
+ label = "user2";
+ gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
+ default-state = "off";
+ };
+ };
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ pps {
+ compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pps>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_5p0v: regulator-5p0v {
+ compatible = "regulator-fixed";
+ regulator-name = "5P0V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c3>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ gpio@23 {
+ compatible = "nxp,pca9555";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c02";
+ reg = <0x51>;
+ pagesize = <16>;
+ };
+
+ eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ };
+
+ eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1672";
+ reg = <0x68>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ adc@48 {
+ compatible = "ti,ads1015";
+ reg = <0x48>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@4 {
+ reg = <4>;
+ ti,gain = <0>;
+ ti,datarate = <5>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ ti,gain = <0>;
+ ti,datarate = <5>;
+ };
+
+ channel@6 {
+ reg = <6>;
+ ti,gain = <0>;
+ ti,datarate = <5>;
+ };
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+ status = "disabled";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+ status = "disabled";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x0001b0b0
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x1b0b0
+ >;
+ };
+};
--
2.9.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* Re: [PATCH v3 1/4] ARM: dts: imx: Add GW5907 board support
2019-12-23 21:44 ` [PATCH v3 1/4] ARM: dts: imx: Add GW5907 board support Robert Jones
@ 2019-12-23 22:05 ` Fabio Estevam
2019-12-23 22:55 ` Bobby Jones
0 siblings, 1 reply; 9+ messages in thread
From: Fabio Estevam @ 2019-12-23 22:05 UTC (permalink / raw)
To: Robert Jones
Cc: Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Pengutronix Kernel Team, NXP Linux Team,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
Tim Harvey
Hi Robert,
On Mon, Dec 23, 2019 at 6:44 PM Robert Jones <rjones@gateworks.com> wrote:
>
> The Gateworks GW5907 is an IMX6 SoC based single board computer with:
> - IMX6Q or IMX6DL
> - 32bit DDR3 DRAM
> - FEC GbE Phy
> - bi-color front-panel LED
> - 256MB NAND boot device
> - Gateworks System Controller (hwmon, pushbutton controller, EEPROM)
> - Digital IO expander (pca9555)
> - Joystick 12bit adc (ads1015)
>
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> Signed-off-by: Robert Jones <rjones@gateworks.com>
Not clear on the authorship on this patch.
If the original author is Tim, then his name should appear in the From field.
> ---
> arch/arm/boot/dts/Makefile | 2 +
> arch/arm/boot/dts/imx6dl-gw5907.dts | 14 ++
> arch/arm/boot/dts/imx6q-gw5907.dts | 14 ++
> arch/arm/boot/dts/imx6qdl-gw5907.dtsi | 399 ++++++++++++++++++++++++++++++++++
> 4 files changed, 429 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-gw5907.dts
> create mode 100644 arch/arm/boot/dts/imx6q-gw5907.dts
> create mode 100644 arch/arm/boot/dts/imx6qdl-gw5907.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 1e9e1af..9ee80e2 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -422,6 +422,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-gw560x.dtb \
> imx6dl-gw5903.dtb \
> imx6dl-gw5904.dtb \
> + imx6dl-gw5907.dtb \
You should add an additional patch that add these new boards in
Documentation/devicetree/bindings/arm/fsl.yaml
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v3 1/4] ARM: dts: imx: Add GW5907 board support
2019-12-23 22:05 ` Fabio Estevam
@ 2019-12-23 22:55 ` Bobby Jones
2019-12-24 1:50 ` Fabio Estevam
0 siblings, 1 reply; 9+ messages in thread
From: Bobby Jones @ 2019-12-23 22:55 UTC (permalink / raw)
To: Fabio Estevam
Cc: Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Pengutronix Kernel Team, NXP Linux Team,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
Tim Harvey
On Mon, Dec 23, 2019 at 2:06 PM Fabio Estevam <festevam@gmail.com> wrote:
>
> Hi Robert,
>
> On Mon, Dec 23, 2019 at 6:44 PM Robert Jones <rjones@gateworks.com> wrote:
> >
> > The Gateworks GW5907 is an IMX6 SoC based single board computer with:
> > - IMX6Q or IMX6DL
> > - 32bit DDR3 DRAM
> > - FEC GbE Phy
> > - bi-color front-panel LED
> > - 256MB NAND boot device
> > - Gateworks System Controller (hwmon, pushbutton controller, EEPROM)
> > - Digital IO expander (pca9555)
> > - Joystick 12bit adc (ads1015)
> >
> > Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> > Signed-off-by: Robert Jones <rjones@gateworks.com>
>
> Not clear on the authorship on this patch.
>
> If the original author is Tim, then his name should appear in the From field.
>
Original author for all but the GW5910 patch was myself. It's probably
not clear here but Tim reviewed the patches prior to submission and
had me add him as a Signed-off-by.
Would it be better to just remove those lines from the patches in this case?
> > ---
> > arch/arm/boot/dts/Makefile | 2 +
> > arch/arm/boot/dts/imx6dl-gw5907.dts | 14 ++
> > arch/arm/boot/dts/imx6q-gw5907.dts | 14 ++
> > arch/arm/boot/dts/imx6qdl-gw5907.dtsi | 399 ++++++++++++++++++++++++++++++++++
> > 4 files changed, 429 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6dl-gw5907.dts
> > create mode 100644 arch/arm/boot/dts/imx6q-gw5907.dts
> > create mode 100644 arch/arm/boot/dts/imx6qdl-gw5907.dtsi
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 1e9e1af..9ee80e2 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -422,6 +422,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6dl-gw560x.dtb \
> > imx6dl-gw5903.dtb \
> > imx6dl-gw5904.dtb \
> > + imx6dl-gw5907.dtb \
>
> You should add an additional patch that add these new boards in
> Documentation/devicetree/bindings/arm/fsl.yaml
So I was planning on just adding an enum line for "gw,ventana" under
the i.MX6DL and i.MX6Q based Boards sections. Would that be
sufficient?
We have a lot of individual custom boards and it doesn't seem correct
to add individual strings for every one in both sections.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v3 1/4] ARM: dts: imx: Add GW5907 board support
2019-12-23 22:55 ` Bobby Jones
@ 2019-12-24 1:50 ` Fabio Estevam
0 siblings, 0 replies; 9+ messages in thread
From: Fabio Estevam @ 2019-12-24 1:50 UTC (permalink / raw)
To: Bobby Jones
Cc: Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Pengutronix Kernel Team, NXP Linux Team,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
Tim Harvey
On Mon, Dec 23, 2019 at 7:55 PM Bobby Jones <rjones@gateworks.com> wrote:
> Original author for all but the GW5910 patch was myself. It's probably
> not clear here but Tim reviewed the patches prior to submission and
> had me add him as a Signed-off-by.
You can add Tim's Reviewed-by tag below your Signed-off-by tag in this case.
> So I was planning on just adding an enum line for "gw,ventana" under
> the i.MX6DL and i.MX6Q based Boards sections. Would that be
> sufficient?
>
> We have a lot of individual custom boards and it doesn't seem correct
> to add individual strings for every one in both sections.
You should add all Ventana dtbs into fsl.yaml.
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH v3 2/4] ARM: dts: imx: Add GW5910 board support
2019-12-23 21:44 [PATCH v3 0/4] ARM: dts: imx: Add GW59xx Gateworks specials Robert Jones
2019-12-23 21:44 ` [PATCH v3 1/4] ARM: dts: imx: Add GW5907 board support Robert Jones
@ 2019-12-23 21:44 ` Robert Jones
2019-12-23 22:07 ` Fabio Estevam
2019-12-23 21:44 ` [PATCH v3 3/4] ARM: dts: imx: Add GW5913 " Robert Jones
2019-12-23 21:44 ` [PATCH v3 4/4] ARM: dts: imx: Add GW5912 " Robert Jones
3 siblings, 1 reply; 9+ messages in thread
From: Robert Jones @ 2019-12-23 21:44 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer
Cc: Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel, linux-arm-kernel, Tim Harvey
From: Tim Harvey <tharvey@gateworks.com>
The Gateworks GW5910 is an IMX6 SoC based single board computer with:
- IMX6Q or IMX6DL
- 32bit DDR3 DRAM
- FEC GbE RJ45 front-panel
- 1x miniPCIe socket with PCI Gen2, USB2
- 1x miniPCIe socket with PCI Gen2, USB2, nanoSIM
- 5V to 60V DC input barrel jack
- 3axis accelerometer (lis2de12)
- GPS (ublox ZOE-M8Q)
- bi-color front-panel LED
- 256MB NAND boot device
- microSD socket (with UHS-I support)
- user pushbutton
- Gateworks System Controller (hwmon, pushbutton controller, EEPROM)
- Dual-Band Wireless MCU (CC1352, UART/I2S interrconnect to IMX6)
- WiFi/Bluetooth/BLE module (Sterling-LSW, SDIO/UART interconnect to IMX6)
- RS232 transceiver (1x UART with flow-control or 2x UART (build option)
- off-board SPI connector (1x chip-select)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-gw5910.dts | 14 +
arch/arm/boot/dts/imx6q-gw5910.dts | 14 +
arch/arm/boot/dts/imx6qdl-gw5910.dtsi | 491 ++++++++++++++++++++++++++++++++++
4 files changed, 521 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-gw5910.dts
create mode 100644 arch/arm/boot/dts/imx6q-gw5910.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-gw5910.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9ee80e2..85e53cc 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -423,6 +423,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-gw5903.dtb \
imx6dl-gw5904.dtb \
imx6dl-gw5907.dtb \
+ imx6dl-gw5910.dtb \
imx6dl-hummingboard.dtb \
imx6dl-hummingboard-emmc-som-v15.dtb \
imx6dl-hummingboard-som-v15.dtb \
@@ -495,6 +496,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-gw5903.dtb \
imx6q-gw5904.dtb \
imx6q-gw5907.dtb \
+ imx6q-gw5910.dtb \
imx6q-h100.dtb \
imx6q-hummingboard.dtb \
imx6q-hummingboard-emmc-som-v15.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-gw5910.dts b/arch/arm/boot/dts/imx6dl-gw5910.dts
new file mode 100644
index 0000000..fbff923
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-gw5910.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw5910.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 DualLite/Solo GW5910";
+ compatible = "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6q-gw5910.dts b/arch/arm/boot/dts/imx6q-gw5910.dts
new file mode 100644
index 0000000..0fed6f9
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-gw5910.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-gw5910.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 Dual/Quad GW5910";
+ compatible = "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
new file mode 100644
index 0000000..be1af74
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
@@ -0,0 +1,491 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ /* these are used by bootloader for disabling nodes */
+ aliases {
+ led0 = &led0;
+ led1 = &led1;
+ led2 = &led2;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led0: user1 {
+ label = "user1";
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led1: user2 {
+ label = "user2";
+ gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
+ default-state = "off";
+ };
+
+ led2: user3 {
+ label = "user3";
+ gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
+ default-state = "off";
+ };
+ };
+
+ pps {
+ compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pps>;
+ gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_5p0v: regulator-5p0v {
+ compatible = "regulator-fixed";
+ regulator-name = "5P0V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_wl: regulator-wl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_wl>;
+ compatible = "regulator-fixed";
+ regulator-name = "wl";
+ gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <100>;
+ enable-active-high;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_bt: regulator-bt {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_bt>;
+ compatible = "regulator-fixed";
+ regulator-name = "bt";
+ gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <100>;
+ enable-active-high;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ gpio@23 {
+ compatible = "nxp,pca9555";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c02";
+ reg = <0x51>;
+ pagesize = <16>;
+ };
+
+ eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ };
+
+ eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1672";
+ reg = <0x68>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ accel@19 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_accel>;
+ compatible = "st,lis2de12";
+ reg = <0x19>;
+ st,drdy-int-pin = <1>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <13 0>;
+ interrupt-names = "INT1";
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+ status = "disabled";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+ status = "disabled";
+};
+
+/* off-board RS232 */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+/* serial console */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+/* Sterling-LWB Bluetooth */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+/* GPS */
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_5p0v>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+/* Sterling-LWB SDIO WiFi */
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ vmmc-supply = <®_3p3v>;
+ non-removable;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
+&iomuxc {
+ pinctrl_accel: accelmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi3: escpi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x100b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x0001b0b0
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_reg_bt: regbtgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b1
+ >;
+ };
+
+ pinctrl_reg_wl: regwlgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x17059 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x170b9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170b9 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170f9 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170f9
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x1b0b0
+ >;
+ };
+};
--
2.9.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* Re: [PATCH v3 2/4] ARM: dts: imx: Add GW5910 board support
2019-12-23 21:44 ` [PATCH v3 2/4] ARM: dts: imx: Add GW5910 " Robert Jones
@ 2019-12-23 22:07 ` Fabio Estevam
0 siblings, 0 replies; 9+ messages in thread
From: Fabio Estevam @ 2019-12-23 22:07 UTC (permalink / raw)
To: Robert Jones
Cc: Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Pengutronix Kernel Team, NXP Linux Team,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
Tim Harvey
On Mon, Dec 23, 2019 at 6:44 PM Robert Jones <rjones@gateworks.com> wrote:
>
> From: Tim Harvey <tharvey@gateworks.com>
>
> The Gateworks GW5910 is an IMX6 SoC based single board computer with:
> - IMX6Q or IMX6DL
> - 32bit DDR3 DRAM
> - FEC GbE RJ45 front-panel
> - 1x miniPCIe socket with PCI Gen2, USB2
> - 1x miniPCIe socket with PCI Gen2, USB2, nanoSIM
> - 5V to 60V DC input barrel jack
> - 3axis accelerometer (lis2de12)
> - GPS (ublox ZOE-M8Q)
> - bi-color front-panel LED
> - 256MB NAND boot device
> - microSD socket (with UHS-I support)
> - user pushbutton
> - Gateworks System Controller (hwmon, pushbutton controller, EEPROM)
> - Dual-Band Wireless MCU (CC1352, UART/I2S interrconnect to IMX6)
> - WiFi/Bluetooth/BLE module (Sterling-LSW, SDIO/UART interconnect to IMX6)
> - RS232 transceiver (1x UART with flow-control or 2x UART (build option)
> - off-board SPI connector (1x chip-select)
>
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Ok, this one has Tim as the author, but since you are submitting it,
you should also add your Signed-off-by below Tim's.
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH v3 3/4] ARM: dts: imx: Add GW5913 board support
2019-12-23 21:44 [PATCH v3 0/4] ARM: dts: imx: Add GW59xx Gateworks specials Robert Jones
2019-12-23 21:44 ` [PATCH v3 1/4] ARM: dts: imx: Add GW5907 board support Robert Jones
2019-12-23 21:44 ` [PATCH v3 2/4] ARM: dts: imx: Add GW5910 " Robert Jones
@ 2019-12-23 21:44 ` Robert Jones
2019-12-23 21:44 ` [PATCH v3 4/4] ARM: dts: imx: Add GW5912 " Robert Jones
3 siblings, 0 replies; 9+ messages in thread
From: Robert Jones @ 2019-12-23 21:44 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer
Cc: Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel, linux-arm-kernel, Robert Jones,
Tim Harvey
The Gateworks GW5913 is an IMX6 SoC based single board computer with:
- IMX6Q or IMX6DL
- 32bit DDR3 DRAM
- FEC GbE RJ45 front-panel
- 1x miniPCIe socket with PCI Gen2, USB2
- 1x miniPCIe socket with PCI Gen2, USB2, nanoSIM
- 6V to 60V DC input connector
- GPS (ublox ZOE-M8Q)
- bi-color front-panel LED
- 256MB NAND boot device
- nanoSIM socket
- user pushbutton
- Gateworks System Controller (hwmon, pushbutton controller, EEPROM)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Robert Jones <rjones@gateworks.com>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-gw5913.dts | 14 ++
arch/arm/boot/dts/imx6q-gw5913.dts | 14 ++
arch/arm/boot/dts/imx6qdl-gw5913.dtsi | 348 ++++++++++++++++++++++++++++++++++
4 files changed, 378 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-gw5913.dts
create mode 100644 arch/arm/boot/dts/imx6q-gw5913.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-gw5913.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 85e53cc..5b059fc 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -424,6 +424,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-gw5904.dtb \
imx6dl-gw5907.dtb \
imx6dl-gw5910.dtb \
+ imx6dl-gw5913.dtb \
imx6dl-hummingboard.dtb \
imx6dl-hummingboard-emmc-som-v15.dtb \
imx6dl-hummingboard-som-v15.dtb \
@@ -497,6 +498,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-gw5904.dtb \
imx6q-gw5907.dtb \
imx6q-gw5910.dtb \
+ imx6q-gw5913.dtb \
imx6q-h100.dtb \
imx6q-hummingboard.dtb \
imx6q-hummingboard-emmc-som-v15.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-gw5913.dts b/arch/arm/boot/dts/imx6dl-gw5913.dts
new file mode 100644
index 0000000..81475c1
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-gw5913.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw5913.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 DualLite/Solo GW5913";
+ compatible = "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6q-gw5913.dts b/arch/arm/boot/dts/imx6q-gw5913.dts
new file mode 100644
index 0000000..09cf350
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-gw5913.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-gw5913.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 Dual/Quad GW5913";
+ compatible = "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi b/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
new file mode 100644
index 0000000..635c203
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
@@ -0,0 +1,348 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ /* these are used by bootloader for disabling nodes */
+ aliases {
+ led0 = &led0;
+ led1 = &led1;
+ nand = &gpmi;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led0: user1 {
+ label = "user1";
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led1: user2 {
+ label = "user2";
+ gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
+ default-state = "off";
+ };
+ };
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x20000000>;
+ };
+
+ pps {
+ compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pps>;
+ gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_5p0v: regulator-5p0v {
+ compatible = "regulator-fixed";
+ regulator-name = "5P0V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ gpio@23 {
+ compatible = "nxp,pca9555";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c02";
+ reg = <0x51>;
+ pagesize = <16>;
+ };
+
+ eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ };
+
+ eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1672";
+ reg = <0x68>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+ status = "disabled";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+ status = "disabled";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x0001b0b0
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x1b0b0
+ >;
+ };
+};
--
2.9.2
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH v3 4/4] ARM: dts: imx: Add GW5912 board support
2019-12-23 21:44 [PATCH v3 0/4] ARM: dts: imx: Add GW59xx Gateworks specials Robert Jones
` (2 preceding siblings ...)
2019-12-23 21:44 ` [PATCH v3 3/4] ARM: dts: imx: Add GW5913 " Robert Jones
@ 2019-12-23 21:44 ` Robert Jones
3 siblings, 0 replies; 9+ messages in thread
From: Robert Jones @ 2019-12-23 21:44 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer
Cc: Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel, linux-arm-kernel, Robert Jones,
Tim Harvey
The Gateworks GW5912 is an IMX6 SoC based single board computer with:
- IMX6Q or IMX6DL
- 32bit DDR3 DRAM
- GbE RJ45 front-panel
- 4x miniPCIe socket with PCI Gen2, USB2
- 1x miniPCIe socket with PCI Gen2, USB2, mSATA
- 1x miniPCIe socket with PCI Gen2, USB2, mezzanine
- 10V to 60V DC input barrel jack
- 3axis accelerometer (lis2de12)
- GPS (ublox ZOE-M8Q)
- bi-color front-panel LED
- 256MB NAND boot device
- nanoSIM/microSD socket (with UHS-I support)
- user pushbutton
- Gateworks System Controller (hwmon, pushbutton controller, EEPROM)
- CAN Bus transceiver (mcp2562)
- RS232 transceiver (1x UART with flow-control or 2x UART (build option)
- off-board SPI connector (1x chip-select)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Robert Jones <rjones@gateworks.com>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-gw5912.dts | 13 +
arch/arm/boot/dts/imx6q-gw5912.dts | 13 +
arch/arm/boot/dts/imx6qdl-gw5912.dtsi | 461 ++++++++++++++++++++++++++++++++++
4 files changed, 489 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-gw5912.dts
create mode 100644 arch/arm/boot/dts/imx6q-gw5912.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-gw5912.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 5b059fc..1a32a7d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -424,6 +424,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-gw5904.dtb \
imx6dl-gw5907.dtb \
imx6dl-gw5910.dtb \
+ imx6dl-gw5912.dtb \
imx6dl-gw5913.dtb \
imx6dl-hummingboard.dtb \
imx6dl-hummingboard-emmc-som-v15.dtb \
@@ -498,6 +499,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-gw5904.dtb \
imx6q-gw5907.dtb \
imx6q-gw5910.dtb \
+ imx6q-gw5912.dtb \
imx6q-gw5913.dtb \
imx6q-h100.dtb \
imx6q-hummingboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-gw5912.dts b/arch/arm/boot/dts/imx6dl-gw5912.dts
new file mode 100644
index 0000000..7dcc5a8
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-gw5912.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw5912.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 DualLite/Solo GW5912";
+ compatible = "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6q-gw5912.dts b/arch/arm/boot/dts/imx6q-gw5912.dts
new file mode 100644
index 0000000..5cee26c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-gw5912.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-gw5912.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 Dual/Quad GW5912";
+ compatible = "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-gw5912.dtsi b/arch/arm/boot/dts/imx6qdl-gw5912.dtsi
new file mode 100644
index 0000000..8c57fd2
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-gw5912.dtsi
@@ -0,0 +1,461 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ /* these are used by bootloader for disabling nodes */
+ aliases {
+ led0 = &led0;
+ led1 = &led1;
+ led2 = &led2;
+ nand = &gpmi;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led0: user1 {
+ label = "user1";
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led1: user2 {
+ label = "user2";
+ gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
+ default-state = "off";
+ };
+
+ led2: user3 {
+ label = "user3";
+ gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
+ default-state = "off";
+ };
+ };
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x40000000>;
+ };
+
+ pps {
+ compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pps>;
+ gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_vbus: regulator-5p0v {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ gpio@23 {
+ compatible = "nxp,pca9555";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c02";
+ reg = <0x51>;
+ pagesize = <16>;
+ };
+
+ eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ };
+
+ eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1672";
+ reg = <0x68>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ accel@19 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_accel>;
+ compatible = "st,lis2de12";
+ reg = <0x19>;
+ st,drdy-int-pin = <1>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <13 0>;
+ interrupt-names = "INT1";
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>; /* MX6_DIO0 */
+ status = "disabled";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+ status = "disabled";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+ status = "disabled";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ rts-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_vbus>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p3v>;
+ no-1-8-v; /* firmware will remove if board revision supports */
+ status = "okay";
+};
+
+&wdog1 {
+ status = "disabled";
+};
+
+&wdog2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_accel: accelmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi2: escpi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x100b1
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b0b1
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b1
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x4001b0b0
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x0001b0b0
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x4001b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x4001b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x17059 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170b9 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170f9 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170f9
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT3__WDOG2_B 0x1b0b0
+ >;
+ };
+};
--
2.9.2
^ permalink raw reply related [flat|nested] 9+ messages in thread