[PATCH v6 00/12] mmc: mediatek: add support of mt2701/mt2712

[PATCH v6 00/12] mmc: mediatek: add support of mt2701/mt2712

[Chaotian Jing]

  This serial of patches are adding support of mt2701/mt2712.
there are many changes and HW improvement between mt8173 and
mt2701/mt2712, below is a list of these changes:
  1. enlarge CLKDIV bits from 8 to 12
  2. remove the PAD_TUNE register and add a new PAD_TUNE0 register
  3. add data sync and async fifo feature
  4. add busy_check feature
  5. add stop_clk fix
  6. add enhance_rx support
  7. add a seperate CG of source clock

  mt2712 supports full of these features, mt2701 supports part of it, and
add a "mediatek,latch-ck" to work-around as it do not support stop-clk fix.

Note: As Pinctrl/CCF are not ready now, so that current patches do not
include DTS part.

Changed vs v5:
  based on Rob's comments, explain why MT8173 no longer compatible with
driver that supports "mediatek,mt8135-mmc", add more clearly description
of "mediatek,latch-ck".

Changed vs v4:
  based on Julien's comment, change the "bool pad_tune0" to "u32 pad_tune_reg".

Changed vs v3:
  based on Ulf's comments, make the bindings change to be the first patch.

Changed vs v2:
  based on Matthias's comments, merge binding file changes to one patch,
add "hs400_tune" flag in dev_comp.

Changed vs v1:
  based on Ulf/Rob/Matthias's comments of DTS binding file, make the binding
file clearly and fix probe issue.


Chaotian Jing (12):
  mmc: dt-bindings: Add reg/source_cg/latch-ck for Mediatek MMC bindings
  mmc: mediatek: add support of mt2701/mt2712
  arm64: dts: mt8173: remove "mediatek,mt8135-mmc" from mmc nodes
  mmc: mediatek: make hs400_tune_response only for mt8173
  mmc: mediatek: add pad_tune0 support
  mmc: mediatek: add async fifo and data tune support
  mmc: mediatek: add busy_check support
  mmc: mediatek: add stop_clk fix and enhance_rx support
  mmc: mediatek: add support of source_cg clock
  mmc: mediatek: add latch-ck support
  mmc: mediatek: improve eMMC hs400 mode read performance
  mmc: mediatek: perfer to use rise edge latching for cmd line

 Documentation/devicetree/bindings/mmc/mtk-sd.txt |  18 +-
 arch/arm64/boot/dts/mediatek/mt8173.dtsi         |  12 +-
 drivers/mmc/host/mtk-sd.c                        | 283 ++++++++++++++++++++---
 3 files changed, 265 insertions(+), 48 deletions(-)

-- 
1.8.1.1.dirty

[PATCH v6 01/12] mmc: dt-bindings: Add reg/source_cg/latch-ck for Mediatek MMC bindings

[Chaotian Jing]

Change the comptiable for support of multi-platform
Make compatible explicit, as MMC host of mt8173 has difference with
mt8135(mt8173 supports hs400 and hs400_tune),so that need separate
mt8173/mt8135 compatible name.
Add description for reg
Add description for source_cg
Add description for mediatek,latch-ck
Note that source_cg and mediatek,latch-ck are optional for some projects,
eg, MT2701 do not have source_cg, and MT2712 do not need
mediatek,latch-ck

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 Documentation/devicetree/bindings/mmc/mtk-sd.txt | 18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
index 4182ea3..72d2a73 100644
--- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt
+++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
@@ -7,10 +7,18 @@ This file documents differences between the core properties in mmc.txt
 and the properties used by the msdc driver.
 
 Required properties:
-- compatible: Should be "mediatek,mt8173-mmc","mediatek,mt8135-mmc"
+- compatible: value should be either of the following.
+	"mediatek,mt8135-mmc": for mmc host ip compatible with mt8135
+	"mediatek,mt8173-mmc": for mmc host ip compatible with mt8173
+	"mediatek,mt2701-mmc": for mmc host ip compatible with mt2701
+	"mediatek,mt2712-mmc": for mmc host ip compatible with mt2712
+- reg: physical base address of the controller and length
 - interrupts: Should contain MSDC interrupt number
-- clocks: MSDC source clock, HCLK
-- clock-names: "source", "hclk"
+- clocks: Should contain phandle for the clock feeding the MMC controller
+- clock-names: Should contain the following:
+	"source" - source clock (required)
+	"hclk" - HCLK which used for host (required)
+	"source_cg" - independent source clock gate (required for MT2712)
 - pinctrl-names: should be "default", "state_uhs"
 - pinctrl-0: should contain default/high speed pin ctrl
 - pinctrl-1: should contain uhs mode pin ctrl
@@ -30,6 +38,10 @@ Optional properties:
 - mediatek,hs400-cmd-resp-sel-rising:  HS400 command response sample selection
 				       If present,HS400 command responses are sampled on rising edges.
 				       If not present,HS400 command responses are sampled on falling edges.
+- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc
+		     error caused by stop clock(fifo full)
+		     Valid range = [0:0x7]. if not present, default value is 0.
+		     applied to compatible "mediatek,mt2701-mmc".
 
 Examples:
 mmc0: mmc@11230000 {
-- 
1.8.1.1.dirty

[PATCH v6 02/12] mmc: mediatek: add support of mt2701/mt2712

[Chaotian Jing]

mt2701/mt2712 has 12bit clock div, which is not compatible with
mt8135/mt8173. and, some additional features will be added in
mt2701/mt2712, so that need distinguish it by comatibale name.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 82 +++++++++++++++++++++++++++++++++++++++--------
 1 file changed, 69 insertions(+), 13 deletions(-)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index 267f7ab..643c795 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -95,6 +95,9 @@
 #define MSDC_CFG_CKDIV          (0xff << 8)	/* RW */
 #define MSDC_CFG_CKMOD          (0x3 << 16)	/* RW */
 #define MSDC_CFG_HS400_CK_MODE  (0x1 << 18)	/* RW */
+#define MSDC_CFG_HS400_CK_MODE_EXTRA  (0x1 << 22)	/* RW */
+#define MSDC_CFG_CKDIV_EXTRA    (0xfff << 8)	/* RW */
+#define MSDC_CFG_CKMOD_EXTRA    (0x3 << 20)	/* RW */
 
 /* MSDC_IOCON mask */
 #define MSDC_IOCON_SDR104CKS    (0x1 << 0)	/* RW */
@@ -295,6 +298,10 @@ struct msdc_save_para {
 	u32 emmc50_cfg0;
 };
 
+struct mtk_mmc_compatible {
+	u8 clk_div_bits;
+};
+
 struct msdc_tune_para {
 	u32 iocon;
 	u32 pad_tune;
@@ -309,6 +316,7 @@ struct msdc_delay_phase {
 
 struct msdc_host {
 	struct device *dev;
+	const struct mtk_mmc_compatible *dev_comp;
 	struct mmc_host *mmc;	/* mmc structure */
 	int cmd_rsp;
 
@@ -350,6 +358,31 @@ struct msdc_host {
 	struct msdc_tune_para saved_tune_para; /* tune result of CMD21/CMD19 */
 };
 
+static const struct mtk_mmc_compatible mt8135_compat = {
+	.clk_div_bits = 8,
+};
+
+static const struct mtk_mmc_compatible mt8173_compat = {
+	.clk_div_bits = 8,
+};
+
+static const struct mtk_mmc_compatible mt2701_compat = {
+	.clk_div_bits = 12,
+};
+
+static const struct mtk_mmc_compatible mt2712_compat = {
+	.clk_div_bits = 12,
+};
+
+static const struct of_device_id msdc_of_ids[] = {
+	{ .compatible = "mediatek,mt8135-mmc", .data = &mt8135_compat},
+	{ .compatible = "mediatek,mt8173-mmc", .data = &mt8173_compat},
+	{ .compatible = "mediatek,mt2701-mmc", .data = &mt2701_compat},
+	{ .compatible = "mediatek,mt2712-mmc", .data = &mt2712_compat},
+	{}
+};
+MODULE_DEVICE_TABLE(of, msdc_of_ids);
+
 static void sdr_set_bits(void __iomem *reg, u32 bs)
 {
 	u32 val = readl(reg);
@@ -509,7 +542,12 @@ static void msdc_set_timeout(struct msdc_host *host, u32 ns, u32 clks)
 		timeout = (ns + clk_ns - 1) / clk_ns + clks;
 		/* in 1048576 sclk cycle unit */
 		timeout = (timeout + (0x1 << 20) - 1) >> 20;
-		sdr_get_field(host->base + MSDC_CFG, MSDC_CFG_CKMOD, &mode);
+		if (host->dev_comp->clk_div_bits == 8)
+			sdr_get_field(host->base + MSDC_CFG,
+				      MSDC_CFG_CKMOD, &mode);
+		else
+			sdr_get_field(host->base + MSDC_CFG,
+				      MSDC_CFG_CKMOD_EXTRA, &mode);
 		/*DDR mode will double the clk cycles for data timeout */
 		timeout = mode >= 2 ? timeout * 2 : timeout;
 		timeout = timeout > 1 ? timeout - 1 : 0;
@@ -548,7 +586,11 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
 
 	flags = readl(host->base + MSDC_INTEN);
 	sdr_clr_bits(host->base + MSDC_INTEN, flags);
-	sdr_clr_bits(host->base + MSDC_CFG, MSDC_CFG_HS400_CK_MODE);
+	if (host->dev_comp->clk_div_bits == 8)
+		sdr_clr_bits(host->base + MSDC_CFG, MSDC_CFG_HS400_CK_MODE);
+	else
+		sdr_clr_bits(host->base + MSDC_CFG,
+			     MSDC_CFG_HS400_CK_MODE_EXTRA);
 	if (timing == MMC_TIMING_UHS_DDR50 ||
 	    timing == MMC_TIMING_MMC_DDR52 ||
 	    timing == MMC_TIMING_MMC_HS400) {
@@ -568,8 +610,12 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
 
 		if (timing == MMC_TIMING_MMC_HS400 &&
 		    hz >= (host->src_clk_freq >> 1)) {
-			sdr_set_bits(host->base + MSDC_CFG,
-				     MSDC_CFG_HS400_CK_MODE);
+			if (host->dev_comp->clk_div_bits == 8)
+				sdr_set_bits(host->base + MSDC_CFG,
+					     MSDC_CFG_HS400_CK_MODE);
+			else
+				sdr_set_bits(host->base + MSDC_CFG,
+					     MSDC_CFG_HS400_CK_MODE_EXTRA);
 			sclk = host->src_clk_freq >> 1;
 			div = 0; /* div is ignore when bit18 is set */
 		}
@@ -587,8 +633,15 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
 			sclk = (host->src_clk_freq >> 2) / div;
 		}
 	}
-	sdr_set_field(host->base + MSDC_CFG, MSDC_CFG_CKMOD | MSDC_CFG_CKDIV,
-		      (mode << 8) | div);
+	if (host->dev_comp->clk_div_bits == 8)
+		sdr_set_field(host->base + MSDC_CFG,
+			      MSDC_CFG_CKMOD | MSDC_CFG_CKDIV,
+			      (mode << 8) | div);
+	else
+		sdr_set_field(host->base + MSDC_CFG,
+			      MSDC_CFG_CKMOD_EXTRA | MSDC_CFG_CKDIV_EXTRA,
+			      (mode << 12) | div);
+
 	sdr_set_bits(host->base + MSDC_CFG, MSDC_CFG_CKPDN);
 	while (!(readl(host->base + MSDC_CFG) & MSDC_CFG_CKSTB))
 		cpu_relax();
@@ -1617,12 +1670,17 @@ static int msdc_drv_probe(struct platform_device *pdev)
 	struct mmc_host *mmc;
 	struct msdc_host *host;
 	struct resource *res;
+	const struct of_device_id *of_id;
 	int ret;
 
 	if (!pdev->dev.of_node) {
 		dev_err(&pdev->dev, "No DT found\n");
 		return -EINVAL;
 	}
+
+	of_id = of_match_node(msdc_of_ids, pdev->dev.of_node);
+	if (!of_id)
+		return -EINVAL;
 	/* Allocate MMC host for this device */
 	mmc = mmc_alloc_host(sizeof(struct msdc_host), &pdev->dev);
 	if (!mmc)
@@ -1686,11 +1744,15 @@ static int msdc_drv_probe(struct platform_device *pdev)
 	msdc_of_property_parse(pdev, host);
 
 	host->dev = &pdev->dev;
+	host->dev_comp = of_id->data;
 	host->mmc = mmc;
 	host->src_clk_freq = clk_get_rate(host->src_clk);
 	/* Set host parameters to mmc */
 	mmc->ops = &mt_msdc_ops;
-	mmc->f_min = DIV_ROUND_UP(host->src_clk_freq, 4 * 255);
+	if (host->dev_comp->clk_div_bits == 8)
+		mmc->f_min = DIV_ROUND_UP(host->src_clk_freq, 4 * 255);
+	else
+		mmc->f_min = DIV_ROUND_UP(host->src_clk_freq, 4 * 4095);
 
 	mmc->caps |= MMC_CAP_ERASE | MMC_CAP_CMD23;
 	/* MMC core transfer sizes tunable parameters */
@@ -1839,12 +1901,6 @@ static int msdc_runtime_resume(struct device *dev)
 	SET_RUNTIME_PM_OPS(msdc_runtime_suspend, msdc_runtime_resume, NULL)
 };
 
-static const struct of_device_id msdc_of_ids[] = {
-	{   .compatible = "mediatek,mt8135-mmc", },
-	{}
-};
-MODULE_DEVICE_TABLE(of, msdc_of_ids);
-
 static struct platform_driver mt_msdc_driver = {
 	.probe = msdc_drv_probe,
 	.remove = msdc_drv_remove,
-- 
1.8.1.1.dirty

[PATCH v6 03/12] arm64: dts: mt8173: remove "mediatek,mt8135-mmc" from mmc nodes

[Chaotian Jing]

devicetree bindings has been updated to support multi-platforms,
so that each platform has its owns compatible name.
And, this compatible name may used in driver to distinguish with
other platform.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 arch/arm64/boot/dts/mediatek/mt8173.dtsi | 12 ++++--------
 1 file changed, 4 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index b99a273..26396ef 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -682,8 +682,7 @@
 		};
 
 		mmc0: mmc@11230000 {
-			compatible = "mediatek,mt8173-mmc",
-				     "mediatek,mt8135-mmc";
+			compatible = "mediatek,mt8173-mmc";
 			reg = <0 0x11230000 0 0x1000>;
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_LOW>;
 			clocks = <&pericfg CLK_PERI_MSDC30_0>,
@@ -693,8 +692,7 @@
 		};
 
 		mmc1: mmc@11240000 {
-			compatible = "mediatek,mt8173-mmc",
-				     "mediatek,mt8135-mmc";
+			compatible = "mediatek,mt8173-mmc";
 			reg = <0 0x11240000 0 0x1000>;
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>;
 			clocks = <&pericfg CLK_PERI_MSDC30_1>,
@@ -704,8 +702,7 @@
 		};
 
 		mmc2: mmc@11250000 {
-			compatible = "mediatek,mt8173-mmc",
-				     "mediatek,mt8135-mmc";
+			compatible = "mediatek,mt8173-mmc";
 			reg = <0 0x11250000 0 0x1000>;
 			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_LOW>;
 			clocks = <&pericfg CLK_PERI_MSDC30_2>,
@@ -715,8 +712,7 @@
 		};
 
 		mmc3: mmc@11260000 {
-			compatible = "mediatek,mt8173-mmc",
-				     "mediatek,mt8135-mmc";
+			compatible = "mediatek,mt8173-mmc";
 			reg = <0 0x11260000 0 0x1000>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_LOW>;
 			clocks = <&pericfg CLK_PERI_MSDC30_3>,
-- 
1.8.1.1.dirty

[PATCH v6 04/12] mmc: mediatek: make hs400_tune_response only for mt8173

[Chaotian Jing]

the origin design of hs400_tune_response is for mt8173 because of
mt8173 has a special design. for doing that, we add a new member
"compatible", by now it's only for mt8173.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index 643c795..ab2fbbb 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -300,6 +300,7 @@ struct msdc_save_para {
 
 struct mtk_mmc_compatible {
 	u8 clk_div_bits;
+	bool hs400_tune; /* only used for MT8173 */
 };
 
 struct msdc_tune_para {
@@ -360,18 +361,22 @@ struct msdc_host {
 
 static const struct mtk_mmc_compatible mt8135_compat = {
 	.clk_div_bits = 8,
+	.hs400_tune = false,
 };
 
 static const struct mtk_mmc_compatible mt8173_compat = {
 	.clk_div_bits = 8,
+	.hs400_tune = true,
 };
 
 static const struct mtk_mmc_compatible mt2701_compat = {
 	.clk_div_bits = 12,
+	.hs400_tune = false,
 };
 
 static const struct mtk_mmc_compatible mt2712_compat = {
 	.clk_div_bits = 12,
+	.hs400_tune = false,
 };
 
 static const struct of_device_id msdc_of_ids[] = {
@@ -666,7 +671,8 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
 		       host->base + PAD_CMD_TUNE);
 	}
 
-	if (timing == MMC_TIMING_MMC_HS400)
+	if (timing == MMC_TIMING_MMC_HS400 &&
+	    host->dev_comp->hs400_tune)
 		sdr_set_field(host->base + PAD_CMD_TUNE,
 			      MSDC_PAD_TUNE_CMDRRDLY,
 			      host->hs400_cmd_int_delay);
@@ -1594,7 +1600,8 @@ static int msdc_execute_tuning(struct mmc_host *mmc, u32 opcode)
 	struct msdc_host *host = mmc_priv(mmc);
 	int ret;
 
-	if (host->hs400_mode)
+	if (host->hs400_mode &&
+	    host->dev_comp->hs400_tune)
 		ret = hs400_tune_response(mmc, opcode);
 	else
 		ret = msdc_tune_response(mmc, opcode);
-- 
1.8.1.1.dirty

[PATCH v6 05/12] mmc: mediatek: add pad_tune0 support

[Chaotian Jing]

from mt2701, the register of PAD_TUNE has been phased out,
while there is a new register of PAD_TUNE0

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 51 ++++++++++++++++++++++++++++++-----------------
 1 file changed, 33 insertions(+), 18 deletions(-)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index ab2fbbb..bcd83d6 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -75,6 +75,7 @@
 #define MSDC_PATCH_BIT   0xb0
 #define MSDC_PATCH_BIT1  0xb4
 #define MSDC_PAD_TUNE    0xec
+#define MSDC_PAD_TUNE0   0xf0
 #define PAD_DS_TUNE      0x188
 #define PAD_CMD_TUNE     0x18c
 #define EMMC50_CFG0      0x208
@@ -301,6 +302,7 @@ struct msdc_save_para {
 struct mtk_mmc_compatible {
 	u8 clk_div_bits;
 	bool hs400_tune; /* only used for MT8173 */
+	u32 pad_tune_reg;
 };
 
 struct msdc_tune_para {
@@ -362,21 +364,25 @@ struct msdc_host {
 static const struct mtk_mmc_compatible mt8135_compat = {
 	.clk_div_bits = 8,
 	.hs400_tune = false,
+	.pad_tune_reg = MSDC_PAD_TUNE,
 };
 
 static const struct mtk_mmc_compatible mt8173_compat = {
 	.clk_div_bits = 8,
 	.hs400_tune = true,
+	.pad_tune_reg = MSDC_PAD_TUNE,
 };
 
 static const struct mtk_mmc_compatible mt2701_compat = {
 	.clk_div_bits = 12,
 	.hs400_tune = false,
+	.pad_tune_reg = MSDC_PAD_TUNE0,
 };
 
 static const struct mtk_mmc_compatible mt2712_compat = {
 	.clk_div_bits = 12,
 	.hs400_tune = false,
+	.pad_tune_reg = MSDC_PAD_TUNE0,
 };
 
 static const struct of_device_id msdc_of_ids[] = {
@@ -581,6 +587,7 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
 	u32 flags;
 	u32 div;
 	u32 sclk;
+	u32 tune_reg = host->dev_comp->pad_tune_reg;
 
 	if (!hz) {
 		dev_dbg(host->dev, "set mclk to 0\n");
@@ -663,10 +670,10 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
 	 */
 	if (host->sclk <= 52000000) {
 		writel(host->def_tune_para.iocon, host->base + MSDC_IOCON);
-		writel(host->def_tune_para.pad_tune, host->base + MSDC_PAD_TUNE);
+		writel(host->def_tune_para.pad_tune, host->base + tune_reg);
 	} else {
 		writel(host->saved_tune_para.iocon, host->base + MSDC_IOCON);
-		writel(host->saved_tune_para.pad_tune, host->base + MSDC_PAD_TUNE);
+		writel(host->saved_tune_para.pad_tune, host->base + tune_reg);
 		writel(host->saved_tune_para.pad_cmd_tune,
 		       host->base + PAD_CMD_TUNE);
 	}
@@ -1224,6 +1231,7 @@ static irqreturn_t msdc_irq(int irq, void *dev_id)
 static void msdc_init_hw(struct msdc_host *host)
 {
 	u32 val;
+	u32 tune_reg = host->dev_comp->pad_tune_reg;
 
 	/* Configure to MMC/SD mode, clock free running */
 	sdr_set_bits(host->base + MSDC_CFG, MSDC_CFG_MODE | MSDC_CFG_CKPDN);
@@ -1239,7 +1247,7 @@ static void msdc_init_hw(struct msdc_host *host)
 	val = readl(host->base + MSDC_INT);
 	writel(val, host->base + MSDC_INT);
 
-	writel(0, host->base + MSDC_PAD_TUNE);
+	writel(0, host->base + tune_reg);
 	writel(0, host->base + MSDC_IOCON);
 	sdr_set_field(host->base + MSDC_IOCON, MSDC_IOCON_DDLSEL, 0);
 	writel(0x403c0046, host->base + MSDC_PATCH_BIT);
@@ -1259,7 +1267,7 @@ static void msdc_init_hw(struct msdc_host *host)
 	sdr_set_field(host->base + SDC_CFG, SDC_CFG_DTOC, 3);
 
 	host->def_tune_para.iocon = readl(host->base + MSDC_IOCON);
-	host->def_tune_para.pad_tune = readl(host->base + MSDC_PAD_TUNE);
+	host->def_tune_para.pad_tune = readl(host->base + tune_reg);
 	dev_dbg(host->dev, "init hardware done!");
 }
 
@@ -1402,18 +1410,19 @@ static int msdc_tune_response(struct mmc_host *mmc, u32 opcode)
 	struct msdc_delay_phase internal_delay_phase;
 	u8 final_delay, final_maxlen;
 	u32 internal_delay = 0;
+	u32 tune_reg = host->dev_comp->pad_tune_reg;
 	int cmd_err;
 	int i, j;
 
 	if (mmc->ios.timing == MMC_TIMING_MMC_HS200 ||
 	    mmc->ios.timing == MMC_TIMING_UHS_SDR104)
-		sdr_set_field(host->base + MSDC_PAD_TUNE,
+		sdr_set_field(host->base + tune_reg,
 			      MSDC_PAD_TUNE_CMDRRDLY,
 			      host->hs200_cmd_int_delay);
 
 	sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_RSPL);
 	for (i = 0 ; i < PAD_DELAY_MAX; i++) {
-		sdr_set_field(host->base + MSDC_PAD_TUNE,
+		sdr_set_field(host->base + tune_reg,
 			      MSDC_PAD_TUNE_CMDRDLY, i);
 		/*
 		 * Using the same parameters, it may sometimes pass the test,
@@ -1437,7 +1446,7 @@ static int msdc_tune_response(struct mmc_host *mmc, u32 opcode)
 
 	sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_RSPL);
 	for (i = 0; i < PAD_DELAY_MAX; i++) {
-		sdr_set_field(host->base + MSDC_PAD_TUNE,
+		sdr_set_field(host->base + tune_reg,
 			      MSDC_PAD_TUNE_CMDRDLY, i);
 		/*
 		 * Using the same parameters, it may sometimes pass the test,
@@ -1462,12 +1471,12 @@ static int msdc_tune_response(struct mmc_host *mmc, u32 opcode)
 		final_maxlen = final_fall_delay.maxlen;
 	if (final_maxlen == final_rise_delay.maxlen) {
 		sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_RSPL);
-		sdr_set_field(host->base + MSDC_PAD_TUNE, MSDC_PAD_TUNE_CMDRDLY,
+		sdr_set_field(host->base + tune_reg, MSDC_PAD_TUNE_CMDRDLY,
 			      final_rise_delay.final_phase);
 		final_delay = final_rise_delay.final_phase;
 	} else {
 		sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_RSPL);
-		sdr_set_field(host->base + MSDC_PAD_TUNE, MSDC_PAD_TUNE_CMDRDLY,
+		sdr_set_field(host->base + tune_reg, MSDC_PAD_TUNE_CMDRDLY,
 			      final_fall_delay.final_phase);
 		final_delay = final_fall_delay.final_phase;
 	}
@@ -1475,7 +1484,7 @@ static int msdc_tune_response(struct mmc_host *mmc, u32 opcode)
 		goto skip_internal;
 
 	for (i = 0; i < PAD_DELAY_MAX; i++) {
-		sdr_set_field(host->base + MSDC_PAD_TUNE,
+		sdr_set_field(host->base + tune_reg,
 			      MSDC_PAD_TUNE_CMDRRDLY, i);
 		mmc_send_tuning(mmc, opcode, &cmd_err);
 		if (!cmd_err)
@@ -1483,7 +1492,7 @@ static int msdc_tune_response(struct mmc_host *mmc, u32 opcode)
 	}
 	dev_dbg(host->dev, "Final internal delay: 0x%x\n", internal_delay);
 	internal_delay_phase = get_best_delay(host, internal_delay);
-	sdr_set_field(host->base + MSDC_PAD_TUNE, MSDC_PAD_TUNE_CMDRRDLY,
+	sdr_set_field(host->base + tune_reg, MSDC_PAD_TUNE_CMDRRDLY,
 		      internal_delay_phase.final_phase);
 skip_internal:
 	dev_dbg(host->dev, "Final cmd pad delay: %x\n", final_delay);
@@ -1545,12 +1554,13 @@ static int msdc_tune_data(struct mmc_host *mmc, u32 opcode)
 	u32 rise_delay = 0, fall_delay = 0;
 	struct msdc_delay_phase final_rise_delay, final_fall_delay = { 0,};
 	u8 final_delay, final_maxlen;
+	u32 tune_reg = host->dev_comp->pad_tune_reg;
 	int i, ret;
 
 	sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_DSPL);
 	sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_W_DSPL);
 	for (i = 0 ; i < PAD_DELAY_MAX; i++) {
-		sdr_set_field(host->base + MSDC_PAD_TUNE,
+		sdr_set_field(host->base + tune_reg,
 			      MSDC_PAD_TUNE_DATRRDLY, i);
 		ret = mmc_send_tuning(mmc, opcode, NULL);
 		if (!ret)
@@ -1565,7 +1575,7 @@ static int msdc_tune_data(struct mmc_host *mmc, u32 opcode)
 	sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_DSPL);
 	sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_W_DSPL);
 	for (i = 0; i < PAD_DELAY_MAX; i++) {
-		sdr_set_field(host->base + MSDC_PAD_TUNE,
+		sdr_set_field(host->base + tune_reg,
 			      MSDC_PAD_TUNE_DATRRDLY, i);
 		ret = mmc_send_tuning(mmc, opcode, NULL);
 		if (!ret)
@@ -1578,14 +1588,14 @@ static int msdc_tune_data(struct mmc_host *mmc, u32 opcode)
 	if (final_maxlen == final_rise_delay.maxlen) {
 		sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_DSPL);
 		sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_W_DSPL);
-		sdr_set_field(host->base + MSDC_PAD_TUNE,
+		sdr_set_field(host->base + tune_reg,
 			      MSDC_PAD_TUNE_DATRRDLY,
 			      final_rise_delay.final_phase);
 		final_delay = final_rise_delay.final_phase;
 	} else {
 		sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_DSPL);
 		sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_W_DSPL);
-		sdr_set_field(host->base + MSDC_PAD_TUNE,
+		sdr_set_field(host->base + tune_reg,
 			      MSDC_PAD_TUNE_DATRRDLY,
 			      final_fall_delay.final_phase);
 		final_delay = final_fall_delay.final_phase;
@@ -1599,6 +1609,7 @@ static int msdc_execute_tuning(struct mmc_host *mmc, u32 opcode)
 {
 	struct msdc_host *host = mmc_priv(mmc);
 	int ret;
+	u32 tune_reg = host->dev_comp->pad_tune_reg;
 
 	if (host->hs400_mode &&
 	    host->dev_comp->hs400_tune)
@@ -1616,7 +1627,7 @@ static int msdc_execute_tuning(struct mmc_host *mmc, u32 opcode)
 	}
 
 	host->saved_tune_para.iocon = readl(host->base + MSDC_IOCON);
-	host->saved_tune_para.pad_tune = readl(host->base + MSDC_PAD_TUNE);
+	host->saved_tune_para.pad_tune = readl(host->base + tune_reg);
 	host->saved_tune_para.pad_cmd_tune = readl(host->base + PAD_CMD_TUNE);
 	return ret;
 }
@@ -1857,10 +1868,12 @@ static int msdc_drv_remove(struct platform_device *pdev)
 #ifdef CONFIG_PM
 static void msdc_save_reg(struct msdc_host *host)
 {
+	u32 tune_reg = host->dev_comp->pad_tune_reg;
+
 	host->save_para.msdc_cfg = readl(host->base + MSDC_CFG);
 	host->save_para.iocon = readl(host->base + MSDC_IOCON);
 	host->save_para.sdc_cfg = readl(host->base + SDC_CFG);
-	host->save_para.pad_tune = readl(host->base + MSDC_PAD_TUNE);
+	host->save_para.pad_tune = readl(host->base + tune_reg);
 	host->save_para.patch_bit0 = readl(host->base + MSDC_PATCH_BIT);
 	host->save_para.patch_bit1 = readl(host->base + MSDC_PATCH_BIT1);
 	host->save_para.pad_ds_tune = readl(host->base + PAD_DS_TUNE);
@@ -1870,10 +1883,12 @@ static void msdc_save_reg(struct msdc_host *host)
 
 static void msdc_restore_reg(struct msdc_host *host)
 {
+	u32 tune_reg = host->dev_comp->pad_tune_reg;
+
 	writel(host->save_para.msdc_cfg, host->base + MSDC_CFG);
 	writel(host->save_para.iocon, host->base + MSDC_IOCON);
 	writel(host->save_para.sdc_cfg, host->base + SDC_CFG);
-	writel(host->save_para.pad_tune, host->base + MSDC_PAD_TUNE);
+	writel(host->save_para.pad_tune, host->base + tune_reg);
 	writel(host->save_para.patch_bit0, host->base + MSDC_PATCH_BIT);
 	writel(host->save_para.patch_bit1, host->base + MSDC_PATCH_BIT1);
 	writel(host->save_para.pad_ds_tune, host->base + PAD_DS_TUNE);
-- 
1.8.1.1.dirty

[PATCH v6 06/12] mmc: mediatek: add async fifo and data tune support

[Chaotian Jing]

mt2701/mt2712 supports async fifo & data tune, which can improve
host stability.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 52 +++++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 50 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index bcd83d6..8113bac 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -74,6 +74,7 @@
 #define MSDC_DMA_CFG     0x9c
 #define MSDC_PATCH_BIT   0xb0
 #define MSDC_PATCH_BIT1  0xb4
+#define MSDC_PATCH_BIT2  0xb8
 #define MSDC_PAD_TUNE    0xec
 #define MSDC_PAD_TUNE0   0xf0
 #define PAD_DS_TUNE      0x188
@@ -216,11 +217,20 @@
 #define MSDC_PATCH_BIT_SPCPUSH    (0x1 << 29)	/* RW */
 #define MSDC_PATCH_BIT_DECRCTMO   (0x1 << 30)	/* RW */
 
+#define MSDC_PATCH_BIT2_CFGRESP   (0x1 << 15)   /* RW */
+#define MSDC_PATCH_BIT2_CFGCRCSTS (0x1 << 28)   /* RW */
+#define MSDC_PB2_RESPWAIT         (0x3 << 2)    /* RW */
+#define MSDC_PB2_RESPSTSENSEL     (0x7 << 16)   /* RW */
+#define MSDC_PB2_CRCSTSENSEL      (0x7 << 29)   /* RW */
+
 #define MSDC_PAD_TUNE_DATWRDLY	  (0x1f <<  0)	/* RW */
 #define MSDC_PAD_TUNE_DATRRDLY	  (0x1f <<  8)	/* RW */
 #define MSDC_PAD_TUNE_CMDRDLY	  (0x1f << 16)  /* RW */
 #define MSDC_PAD_TUNE_CMDRRDLY	  (0x1f << 22)	/* RW */
 #define MSDC_PAD_TUNE_CLKTDLY	  (0x1f << 27)  /* RW */
+#define MSDC_PAD_TUNE_RXDLYSEL	  (0x1 << 15)   /* RW */
+#define MSDC_PAD_TUNE_RD_SEL	  (0x1 << 13)   /* RW */
+#define MSDC_PAD_TUNE_CMD_SEL	  (0x1 << 21)   /* RW */
 
 #define PAD_DS_TUNE_DLY1	  (0x1f << 2)   /* RW */
 #define PAD_DS_TUNE_DLY2	  (0x1f << 7)   /* RW */
@@ -294,6 +304,7 @@ struct msdc_save_para {
 	u32 pad_tune;
 	u32 patch_bit0;
 	u32 patch_bit1;
+	u32 patch_bit2;
 	u32 pad_ds_tune;
 	u32 pad_cmd_tune;
 	u32 emmc50_cfg0;
@@ -303,6 +314,8 @@ struct mtk_mmc_compatible {
 	u8 clk_div_bits;
 	bool hs400_tune; /* only used for MT8173 */
 	u32 pad_tune_reg;
+	bool async_fifo;
+	bool data_tune;
 };
 
 struct msdc_tune_para {
@@ -365,24 +378,32 @@ struct msdc_host {
 	.clk_div_bits = 8,
 	.hs400_tune = false,
 	.pad_tune_reg = MSDC_PAD_TUNE,
+	.async_fifo = false,
+	.data_tune = false,
 };
 
 static const struct mtk_mmc_compatible mt8173_compat = {
 	.clk_div_bits = 8,
 	.hs400_tune = true,
 	.pad_tune_reg = MSDC_PAD_TUNE,
+	.async_fifo = false,
+	.data_tune = false,
 };
 
 static const struct mtk_mmc_compatible mt2701_compat = {
 	.clk_div_bits = 12,
 	.hs400_tune = false,
 	.pad_tune_reg = MSDC_PAD_TUNE0,
+	.async_fifo = true,
+	.data_tune = true,
 };
 
 static const struct mtk_mmc_compatible mt2712_compat = {
 	.clk_div_bits = 12,
 	.hs400_tune = false,
 	.pad_tune_reg = MSDC_PAD_TUNE0,
+	.async_fifo = true,
+	.data_tune = true,
 };
 
 static const struct of_device_id msdc_of_ids[] = {
@@ -1252,8 +1273,29 @@ static void msdc_init_hw(struct msdc_host *host)
 	sdr_set_field(host->base + MSDC_IOCON, MSDC_IOCON_DDLSEL, 0);
 	writel(0x403c0046, host->base + MSDC_PATCH_BIT);
 	sdr_set_field(host->base + MSDC_PATCH_BIT, MSDC_CKGEN_MSDC_DLY_SEL, 1);
-	writel(0xffff0089, host->base + MSDC_PATCH_BIT1);
+	writel(0xffff4089, host->base + MSDC_PATCH_BIT1);
 	sdr_set_bits(host->base + EMMC50_CFG0, EMMC50_CFG_CFCSTS_SEL);
+	if (host->dev_comp->async_fifo) {
+		sdr_set_field(host->base + MSDC_PATCH_BIT2,
+			      MSDC_PB2_RESPWAIT, 3);
+		sdr_set_field(host->base + MSDC_PATCH_BIT2,
+			      MSDC_PB2_RESPSTSENSEL, 2);
+		sdr_set_field(host->base + MSDC_PATCH_BIT2,
+			      MSDC_PB2_CRCSTSENSEL, 2);
+		/* use async fifo, then no need tune internal delay */
+		sdr_clr_bits(host->base + MSDC_PATCH_BIT2,
+			     MSDC_PATCH_BIT2_CFGRESP);
+		sdr_set_bits(host->base + MSDC_PATCH_BIT2,
+			     MSDC_PATCH_BIT2_CFGCRCSTS);
+	}
+
+	if (host->dev_comp->data_tune) {
+		sdr_set_bits(host->base + tune_reg,
+			     MSDC_PAD_TUNE_RD_SEL | MSDC_PAD_TUNE_CMD_SEL);
+	} else {
+		/* choose clock tune */
+		sdr_set_bits(host->base + tune_reg, MSDC_PAD_TUNE_RXDLYSEL);
+	}
 
 	/* Configure to enable SDIO mode.
 	 * it's must otherwise sdio cmd5 failed
@@ -1268,6 +1310,8 @@ static void msdc_init_hw(struct msdc_host *host)
 
 	host->def_tune_para.iocon = readl(host->base + MSDC_IOCON);
 	host->def_tune_para.pad_tune = readl(host->base + tune_reg);
+	host->saved_tune_para.iocon = readl(host->base + MSDC_IOCON);
+	host->saved_tune_para.pad_tune = readl(host->base + tune_reg);
 	dev_dbg(host->dev, "init hardware done!");
 }
 
@@ -1480,7 +1524,7 @@ static int msdc_tune_response(struct mmc_host *mmc, u32 opcode)
 			      final_fall_delay.final_phase);
 		final_delay = final_fall_delay.final_phase;
 	}
-	if (host->hs200_cmd_int_delay)
+	if (host->dev_comp->async_fifo || host->hs200_cmd_int_delay)
 		goto skip_internal;
 
 	for (i = 0; i < PAD_DELAY_MAX; i++) {
@@ -1638,6 +1682,8 @@ static int msdc_prepare_hs400_tuning(struct mmc_host *mmc, struct mmc_ios *ios)
 	host->hs400_mode = true;
 
 	writel(host->hs400_ds_delay, host->base + PAD_DS_TUNE);
+	/* hs400 mode must set it to 0 */
+	sdr_clr_bits(host->base + MSDC_PATCH_BIT2, MSDC_PATCH_BIT2_CFGCRCSTS);
 	return 0;
 }
 
@@ -1876,6 +1922,7 @@ static void msdc_save_reg(struct msdc_host *host)
 	host->save_para.pad_tune = readl(host->base + tune_reg);
 	host->save_para.patch_bit0 = readl(host->base + MSDC_PATCH_BIT);
 	host->save_para.patch_bit1 = readl(host->base + MSDC_PATCH_BIT1);
+	host->save_para.patch_bit2 = readl(host->base + MSDC_PATCH_BIT2);
 	host->save_para.pad_ds_tune = readl(host->base + PAD_DS_TUNE);
 	host->save_para.pad_cmd_tune = readl(host->base + PAD_CMD_TUNE);
 	host->save_para.emmc50_cfg0 = readl(host->base + EMMC50_CFG0);
@@ -1891,6 +1938,7 @@ static void msdc_restore_reg(struct msdc_host *host)
 	writel(host->save_para.pad_tune, host->base + tune_reg);
 	writel(host->save_para.patch_bit0, host->base + MSDC_PATCH_BIT);
 	writel(host->save_para.patch_bit1, host->base + MSDC_PATCH_BIT1);
+	writel(host->save_para.patch_bit2, host->base + MSDC_PATCH_BIT2);
 	writel(host->save_para.pad_ds_tune, host->base + PAD_DS_TUNE);
 	writel(host->save_para.pad_cmd_tune, host->base + PAD_CMD_TUNE);
 	writel(host->save_para.emmc50_cfg0, host->base + EMMC50_CFG0);
-- 
1.8.1.1.dirty

[PATCH v6 07/12] mmc: mediatek: add busy_check support

[Chaotian Jing]

bit7 of PATCH_BIT1 has different meaning in new design, to
compatible with previous platform, clear this bit in new
platform.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index 8113bac..eceaee8 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -316,6 +316,7 @@ struct mtk_mmc_compatible {
 	u32 pad_tune_reg;
 	bool async_fifo;
 	bool data_tune;
+	bool busy_check;
 };
 
 struct msdc_tune_para {
@@ -380,6 +381,7 @@ struct msdc_host {
 	.pad_tune_reg = MSDC_PAD_TUNE,
 	.async_fifo = false,
 	.data_tune = false,
+	.busy_check = false,
 };
 
 static const struct mtk_mmc_compatible mt8173_compat = {
@@ -388,6 +390,7 @@ struct msdc_host {
 	.pad_tune_reg = MSDC_PAD_TUNE,
 	.async_fifo = false,
 	.data_tune = false,
+	.busy_check = false,
 };
 
 static const struct mtk_mmc_compatible mt2701_compat = {
@@ -396,6 +399,7 @@ struct msdc_host {
 	.pad_tune_reg = MSDC_PAD_TUNE0,
 	.async_fifo = true,
 	.data_tune = true,
+	.busy_check = false,
 };
 
 static const struct mtk_mmc_compatible mt2712_compat = {
@@ -404,6 +408,7 @@ struct msdc_host {
 	.pad_tune_reg = MSDC_PAD_TUNE0,
 	.async_fifo = true,
 	.data_tune = true,
+	.busy_check = true,
 };
 
 static const struct of_device_id msdc_of_ids[] = {
@@ -1275,6 +1280,8 @@ static void msdc_init_hw(struct msdc_host *host)
 	sdr_set_field(host->base + MSDC_PATCH_BIT, MSDC_CKGEN_MSDC_DLY_SEL, 1);
 	writel(0xffff4089, host->base + MSDC_PATCH_BIT1);
 	sdr_set_bits(host->base + EMMC50_CFG0, EMMC50_CFG_CFCSTS_SEL);
+	if (host->dev_comp->busy_check)
+		sdr_clr_bits(host->base + MSDC_PATCH_BIT1, (1 << 7));
 	if (host->dev_comp->async_fifo) {
 		sdr_set_field(host->base + MSDC_PATCH_BIT2,
 			      MSDC_PB2_RESPWAIT, 3);
-- 
1.8.1.1.dirty

[PATCH v6 08/12] mmc: mediatek: add stop_clk fix and enhance_rx support

[Chaotian Jing]

mt2712 supports stop_clk fix and enhance_rx, which can improve
host stability.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 47 +++++++++++++++++++++++++++++++++++++++++++----
 1 file changed, 43 insertions(+), 4 deletions(-)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index eceaee8..94d16a3 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -67,6 +67,7 @@
 #define SDC_RESP2        0x48
 #define SDC_RESP3        0x4c
 #define SDC_BLK_NUM      0x50
+#define SDC_ADV_CFG0     0x64
 #define EMMC_IOCON       0x7c
 #define SDC_ACMD_RESP    0x80
 #define MSDC_DMA_SA      0x90
@@ -80,6 +81,7 @@
 #define PAD_DS_TUNE      0x188
 #define PAD_CMD_TUNE     0x18c
 #define EMMC50_CFG0      0x208
+#define SDC_FIFO_CFG     0x228
 
 /*--------------------------------------------------------------------------*/
 /* Register Mask                                                            */
@@ -188,6 +190,9 @@
 #define SDC_STS_CMDBUSY         (0x1 << 1)	/* RW */
 #define SDC_STS_SWR_COMPL       (0x1 << 31)	/* RW */
 
+/* SDC_ADV_CFG0 mask */
+#define SDC_RX_ENHANCE_EN	(0x1 << 20)	/* RW */
+
 /* MSDC_DMA_CTRL mask */
 #define MSDC_DMA_CTRL_START     (0x1 << 0)	/* W */
 #define MSDC_DMA_CTRL_STOP      (0x1 << 1)	/* W */
@@ -217,6 +222,8 @@
 #define MSDC_PATCH_BIT_SPCPUSH    (0x1 << 29)	/* RW */
 #define MSDC_PATCH_BIT_DECRCTMO   (0x1 << 30)	/* RW */
 
+#define MSDC_PATCH_BIT1_STOP_DLY  (0xf << 8)    /* RW */
+
 #define MSDC_PATCH_BIT2_CFGRESP   (0x1 << 15)   /* RW */
 #define MSDC_PATCH_BIT2_CFGCRCSTS (0x1 << 28)   /* RW */
 #define MSDC_PB2_RESPWAIT         (0x3 << 2)    /* RW */
@@ -242,6 +249,9 @@
 #define EMMC50_CFG_CRCSTS_EDGE    (0x1 << 3)   /* RW */
 #define EMMC50_CFG_CFCSTS_SEL     (0x1 << 4)   /* RW */
 
+#define SDC_FIFO_CFG_WRVALIDSEL   (0x1 << 24)  /* RW */
+#define SDC_FIFO_CFG_RDVALIDSEL   (0x1 << 25)  /* RW */
+
 #define REQ_CMD_EIO  (0x1 << 0)
 #define REQ_CMD_TMO  (0x1 << 1)
 #define REQ_DAT_ERR  (0x1 << 2)
@@ -308,6 +318,7 @@ struct msdc_save_para {
 	u32 pad_ds_tune;
 	u32 pad_cmd_tune;
 	u32 emmc50_cfg0;
+	u32 sdc_fifo_cfg;
 };
 
 struct mtk_mmc_compatible {
@@ -317,6 +328,8 @@ struct mtk_mmc_compatible {
 	bool async_fifo;
 	bool data_tune;
 	bool busy_check;
+	bool stop_clk_fix;
+	bool enhance_rx;
 };
 
 struct msdc_tune_para {
@@ -382,6 +395,8 @@ struct msdc_host {
 	.async_fifo = false,
 	.data_tune = false,
 	.busy_check = false,
+	.stop_clk_fix = false,
+	.enhance_rx = false,
 };
 
 static const struct mtk_mmc_compatible mt8173_compat = {
@@ -391,6 +406,8 @@ struct msdc_host {
 	.async_fifo = false,
 	.data_tune = false,
 	.busy_check = false,
+	.stop_clk_fix = false,
+	.enhance_rx = false,
 };
 
 static const struct mtk_mmc_compatible mt2701_compat = {
@@ -400,6 +417,8 @@ struct msdc_host {
 	.async_fifo = true,
 	.data_tune = true,
 	.busy_check = false,
+	.stop_clk_fix = false,
+	.enhance_rx = false,
 };
 
 static const struct mtk_mmc_compatible mt2712_compat = {
@@ -409,6 +428,8 @@ struct msdc_host {
 	.async_fifo = true,
 	.data_tune = true,
 	.busy_check = true,
+	.stop_clk_fix = true,
+	.enhance_rx = true,
 };
 
 static const struct of_device_id msdc_of_ids[] = {
@@ -1280,15 +1301,31 @@ static void msdc_init_hw(struct msdc_host *host)
 	sdr_set_field(host->base + MSDC_PATCH_BIT, MSDC_CKGEN_MSDC_DLY_SEL, 1);
 	writel(0xffff4089, host->base + MSDC_PATCH_BIT1);
 	sdr_set_bits(host->base + EMMC50_CFG0, EMMC50_CFG_CFCSTS_SEL);
+
+	if (host->dev_comp->stop_clk_fix) {
+		sdr_set_field(host->base + MSDC_PATCH_BIT1,
+			      MSDC_PATCH_BIT1_STOP_DLY, 3);
+		sdr_clr_bits(host->base + SDC_FIFO_CFG,
+			     SDC_FIFO_CFG_WRVALIDSEL);
+		sdr_clr_bits(host->base + SDC_FIFO_CFG,
+			     SDC_FIFO_CFG_RDVALIDSEL);
+	}
+
 	if (host->dev_comp->busy_check)
 		sdr_clr_bits(host->base + MSDC_PATCH_BIT1, (1 << 7));
+
 	if (host->dev_comp->async_fifo) {
 		sdr_set_field(host->base + MSDC_PATCH_BIT2,
 			      MSDC_PB2_RESPWAIT, 3);
-		sdr_set_field(host->base + MSDC_PATCH_BIT2,
-			      MSDC_PB2_RESPSTSENSEL, 2);
-		sdr_set_field(host->base + MSDC_PATCH_BIT2,
-			      MSDC_PB2_CRCSTSENSEL, 2);
+		if (host->dev_comp->enhance_rx) {
+			sdr_set_bits(host->base + SDC_ADV_CFG0,
+				     SDC_RX_ENHANCE_EN);
+		} else {
+			sdr_set_field(host->base + MSDC_PATCH_BIT2,
+				      MSDC_PB2_RESPSTSENSEL, 2);
+			sdr_set_field(host->base + MSDC_PATCH_BIT2,
+				      MSDC_PB2_CRCSTSENSEL, 2);
+		}
 		/* use async fifo, then no need tune internal delay */
 		sdr_clr_bits(host->base + MSDC_PATCH_BIT2,
 			     MSDC_PATCH_BIT2_CFGRESP);
@@ -1933,6 +1970,7 @@ static void msdc_save_reg(struct msdc_host *host)
 	host->save_para.pad_ds_tune = readl(host->base + PAD_DS_TUNE);
 	host->save_para.pad_cmd_tune = readl(host->base + PAD_CMD_TUNE);
 	host->save_para.emmc50_cfg0 = readl(host->base + EMMC50_CFG0);
+	host->save_para.sdc_fifo_cfg = readl(host->base + SDC_FIFO_CFG);
 }
 
 static void msdc_restore_reg(struct msdc_host *host)
@@ -1949,6 +1987,7 @@ static void msdc_restore_reg(struct msdc_host *host)
 	writel(host->save_para.pad_ds_tune, host->base + PAD_DS_TUNE);
 	writel(host->save_para.pad_cmd_tune, host->base + PAD_CMD_TUNE);
 	writel(host->save_para.emmc50_cfg0, host->base + EMMC50_CFG0);
+	writel(host->save_para.sdc_fifo_cfg, host->base + SDC_FIFO_CFG);
 }
 
 static int msdc_runtime_suspend(struct device *dev)
-- 
1.8.1.1.dirty

[PATCH v6 09/12] mmc: mediatek: add support of source_cg clock

[Chaotian Jing]

source clock need an independent cg to control, when doing clk mode
switch, need gate source clock to avoid hw issue(multi-bit sync hw hang)

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 23 ++++++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index 94d16a3..a2f26c9 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -372,6 +372,7 @@ struct msdc_host {
 
 	struct clk *src_clk;	/* msdc source clock */
 	struct clk *h_clk;      /* msdc h_clk */
+	struct clk *src_clk_cg; /* msdc source clock control gate */
 	u32 mclk;		/* mmc subsystem clock frequency */
 	u32 src_clk_freq;	/* source clock frequency */
 	u32 sclk;		/* SD/MS bus clock frequency */
@@ -616,6 +617,7 @@ static void msdc_set_timeout(struct msdc_host *host, u32 ns, u32 clks)
 
 static void msdc_gate_clock(struct msdc_host *host)
 {
+	clk_disable_unprepare(host->src_clk_cg);
 	clk_disable_unprepare(host->src_clk);
 	clk_disable_unprepare(host->h_clk);
 }
@@ -624,6 +626,7 @@ static void msdc_ungate_clock(struct msdc_host *host)
 {
 	clk_prepare_enable(host->h_clk);
 	clk_prepare_enable(host->src_clk);
+	clk_prepare_enable(host->src_clk_cg);
 	while (!(readl(host->base + MSDC_CFG) & MSDC_CFG_CKSTB))
 		cpu_relax();
 }
@@ -692,6 +695,15 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
 			sclk = (host->src_clk_freq >> 2) / div;
 		}
 	}
+	sdr_clr_bits(host->base + MSDC_CFG, MSDC_CFG_CKPDN);
+	/*
+	 * As src_clk/HCLK use the same bit to gate/ungate,
+	 * So if want to only gate src_clk, need gate its parent(mux).
+	 */
+	if (host->src_clk_cg)
+		clk_disable_unprepare(host->src_clk_cg);
+	else
+		clk_disable_unprepare(clk_get_parent(host->src_clk));
 	if (host->dev_comp->clk_div_bits == 8)
 		sdr_set_field(host->base + MSDC_CFG,
 			      MSDC_CFG_CKMOD | MSDC_CFG_CKDIV,
@@ -700,10 +712,14 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
 		sdr_set_field(host->base + MSDC_CFG,
 			      MSDC_CFG_CKMOD_EXTRA | MSDC_CFG_CKDIV_EXTRA,
 			      (mode << 12) | div);
+	if (host->src_clk_cg)
+		clk_prepare_enable(host->src_clk_cg);
+	else
+		clk_prepare_enable(clk_get_parent(host->src_clk));
 
-	sdr_set_bits(host->base + MSDC_CFG, MSDC_CFG_CKPDN);
 	while (!(readl(host->base + MSDC_CFG) & MSDC_CFG_CKSTB))
 		cpu_relax();
+	sdr_set_bits(host->base + MSDC_CFG, MSDC_CFG_CKPDN);
 	host->sclk = sclk;
 	host->mclk = hz;
 	host->timing = timing;
@@ -1822,6 +1838,11 @@ static int msdc_drv_probe(struct platform_device *pdev)
 		goto host_free;
 	}
 
+	/*source clock control gate is optional clock*/
+	host->src_clk_cg = devm_clk_get(&pdev->dev, "source_cg");
+	if (IS_ERR(host->src_clk_cg))
+		host->src_clk_cg = NULL;
+
 	host->irq = platform_get_irq(pdev, 0);
 	if (host->irq < 0) {
 		ret = -EINVAL;
-- 
1.8.1.1.dirty

[PATCH v6 10/12] mmc: mediatek: add latch-ck support

[Chaotian Jing]

some platform(eg.mt2701) does not support "stop clk fix", in
this case, need set correct latch-ck to avoid crc error caused
by stop clock block-internally.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index a2f26c9..d75a93d 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -378,6 +378,7 @@ struct msdc_host {
 	u32 sclk;		/* SD/MS bus clock frequency */
 	unsigned char timing;
 	bool vqmmc_enabled;
+	u32 latch_ck;
 	u32 hs400_ds_delay;
 	u32 hs200_cmd_int_delay; /* cmd internal delay for HS200/SDR104 */
 	u32 hs400_cmd_int_delay; /* cmd internal delay for HS400 */
@@ -1661,6 +1662,8 @@ static int msdc_tune_data(struct mmc_host *mmc, u32 opcode)
 	u32 tune_reg = host->dev_comp->pad_tune_reg;
 	int i, ret;
 
+	sdr_set_field(host->base + MSDC_PATCH_BIT, MSDC_INT_DAT_LATCH_CK_SEL,
+		      host->latch_ck);
 	sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_DSPL);
 	sdr_clr_bits(host->base + MSDC_IOCON, MSDC_IOCON_W_DSPL);
 	for (i = 0 ; i < PAD_DELAY_MAX; i++) {
@@ -1773,6 +1776,9 @@ static void msdc_hw_reset(struct mmc_host *mmc)
 static void msdc_of_property_parse(struct platform_device *pdev,
 				   struct msdc_host *host)
 {
+	of_property_read_u32(pdev->dev.of_node, "mediatek,latch-ck",
+			     &host->latch_ck);
+
 	of_property_read_u32(pdev->dev.of_node, "hs400-ds-delay",
 			     &host->hs400_ds_delay);
 
-- 
1.8.1.1.dirty

[PATCH v6 11/12] mmc: mediatek: improve eMMC hs400 mode read performance

[Chaotian Jing]

enlarge outstanding value to improve read performance

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index d75a93d..95759bb 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -81,6 +81,7 @@
 #define PAD_DS_TUNE      0x188
 #define PAD_CMD_TUNE     0x18c
 #define EMMC50_CFG0      0x208
+#define EMMC50_CFG3      0x220
 #define SDC_FIFO_CFG     0x228
 
 /*--------------------------------------------------------------------------*/
@@ -249,6 +250,8 @@
 #define EMMC50_CFG_CRCSTS_EDGE    (0x1 << 3)   /* RW */
 #define EMMC50_CFG_CFCSTS_SEL     (0x1 << 4)   /* RW */
 
+#define EMMC50_CFG3_OUTS_WR       (0x1f << 0)  /* RW */
+
 #define SDC_FIFO_CFG_WRVALIDSEL   (0x1 << 24)  /* RW */
 #define SDC_FIFO_CFG_RDVALIDSEL   (0x1 << 25)  /* RW */
 
@@ -318,6 +321,7 @@ struct msdc_save_para {
 	u32 pad_ds_tune;
 	u32 pad_cmd_tune;
 	u32 emmc50_cfg0;
+	u32 emmc50_cfg3;
 	u32 sdc_fifo_cfg;
 };
 
@@ -1747,6 +1751,9 @@ static int msdc_prepare_hs400_tuning(struct mmc_host *mmc, struct mmc_ios *ios)
 	writel(host->hs400_ds_delay, host->base + PAD_DS_TUNE);
 	/* hs400 mode must set it to 0 */
 	sdr_clr_bits(host->base + MSDC_PATCH_BIT2, MSDC_PATCH_BIT2_CFGCRCSTS);
+	/* to improve read performance, set outstanding to 2 */
+	sdr_set_field(host->base + EMMC50_CFG3, EMMC50_CFG3_OUTS_WR, 2);
+
 	return 0;
 }
 
@@ -1997,6 +2004,7 @@ static void msdc_save_reg(struct msdc_host *host)
 	host->save_para.pad_ds_tune = readl(host->base + PAD_DS_TUNE);
 	host->save_para.pad_cmd_tune = readl(host->base + PAD_CMD_TUNE);
 	host->save_para.emmc50_cfg0 = readl(host->base + EMMC50_CFG0);
+	host->save_para.emmc50_cfg3 = readl(host->base + EMMC50_CFG3);
 	host->save_para.sdc_fifo_cfg = readl(host->base + SDC_FIFO_CFG);
 }
 
@@ -2014,6 +2022,7 @@ static void msdc_restore_reg(struct msdc_host *host)
 	writel(host->save_para.pad_ds_tune, host->base + PAD_DS_TUNE);
 	writel(host->save_para.pad_cmd_tune, host->base + PAD_CMD_TUNE);
 	writel(host->save_para.emmc50_cfg0, host->base + EMMC50_CFG0);
+	writel(host->save_para.emmc50_cfg3, host->base + EMMC50_CFG3);
 	writel(host->save_para.sdc_fifo_cfg, host->base + SDC_FIFO_CFG);
 }
 
-- 
1.8.1.1.dirty

[PATCH v6 12/12] mmc: mediatek: perfer to use rise edge latching for cmd line

[Chaotian Jing]

data lines have applied to perfer to use rise edge, also need
apply it to cmd line.

Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
 drivers/mmc/host/mtk-sd.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index 95759bb..27a6225 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -1550,7 +1550,8 @@ static int msdc_tune_response(struct mmc_host *mmc, u32 opcode)
 	}
 	final_rise_delay = get_best_delay(host, rise_delay);
 	/* if rising edge has enough margin, then do not scan falling edge */
-	if (final_rise_delay.maxlen >= 12 && final_rise_delay.start < 4)
+	if (final_rise_delay.maxlen >= 12 ||
+	    (final_rise_delay.start == 0 && final_rise_delay.maxlen >= 4))
 		goto skip_fall;
 
 	sdr_set_bits(host->base + MSDC_IOCON, MSDC_IOCON_RSPL);
-- 
1.8.1.1.dirty

Re: [PATCH v6 01/12] mmc: dt-bindings: Add reg/source_cg/latch-ck for Mediatek MMC bindings

[Chaotian Jing]

Hi Rob & Ulf,

Gentle ping...
Any other comments about this series of patch ?
On Mon, 2017-10-16 at 09:46 +0800, Chaotian Jing wrote:
> Change the comptiable for support of multi-platform
> Make compatible explicit, as MMC host of mt8173 has difference with
> mt8135(mt8173 supports hs400 and hs400_tune),so that need separate
> mt8173/mt8135 compatible name.
> Add description for reg
> Add description for source_cg
> Add description for mediatek,latch-ck
> Note that source_cg and mediatek,latch-ck are optional for some projects,
> eg, MT2701 do not have source_cg, and MT2712 do not need
> mediatek,latch-ck
> 
> Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
> ---
>  Documentation/devicetree/bindings/mmc/mtk-sd.txt | 18 +++++++++++++++---
>  1 file changed, 15 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> index 4182ea3..72d2a73 100644
> --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> @@ -7,10 +7,18 @@ This file documents differences between the core properties in mmc.txt
>  and the properties used by the msdc driver.
>  
>  Required properties:
> -- compatible: Should be "mediatek,mt8173-mmc","mediatek,mt8135-mmc"
> +- compatible: value should be either of the following.
> +	"mediatek,mt8135-mmc": for mmc host ip compatible with mt8135
> +	"mediatek,mt8173-mmc": for mmc host ip compatible with mt8173
> +	"mediatek,mt2701-mmc": for mmc host ip compatible with mt2701
> +	"mediatek,mt2712-mmc": for mmc host ip compatible with mt2712
> +- reg: physical base address of the controller and length
>  - interrupts: Should contain MSDC interrupt number
> -- clocks: MSDC source clock, HCLK
> -- clock-names: "source", "hclk"
> +- clocks: Should contain phandle for the clock feeding the MMC controller
> +- clock-names: Should contain the following:
> +	"source" - source clock (required)
> +	"hclk" - HCLK which used for host (required)
> +	"source_cg" - independent source clock gate (required for MT2712)
>  - pinctrl-names: should be "default", "state_uhs"
>  - pinctrl-0: should contain default/high speed pin ctrl
>  - pinctrl-1: should contain uhs mode pin ctrl
> @@ -30,6 +38,10 @@ Optional properties:
>  - mediatek,hs400-cmd-resp-sel-rising:  HS400 command response sample selection
>  				       If present,HS400 command responses are sampled on rising edges.
>  				       If not present,HS400 command responses are sampled on falling edges.
> +- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc
> +		     error caused by stop clock(fifo full)
> +		     Valid range = [0:0x7]. if not present, default value is 0.
> +		     applied to compatible "mediatek,mt2701-mmc".
>  
>  Examples:
>  mmc0: mmc@11230000 {

Re: [PATCH v6 01/12] mmc: dt-bindings: Add reg/source_cg/latch-ck for Mediatek MMC bindings

[Rob Herring]

On Mon, Oct 16, 2017 at 09:46:28AM +0800, Chaotian Jing wrote:
> Change the comptiable for support of multi-platform
> Make compatible explicit, as MMC host of mt8173 has difference with
> mt8135(mt8173 supports hs400 and hs400_tune),so that need separate
> mt8173/mt8135 compatible name.
> Add description for reg
> Add description for source_cg
> Add description for mediatek,latch-ck
> Note that source_cg and mediatek,latch-ck are optional for some projects,
> eg, MT2701 do not have source_cg, and MT2712 do not need
> mediatek,latch-ck
> 
> Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
> ---
>  Documentation/devicetree/bindings/mmc/mtk-sd.txt | 18 +++++++++++++++---
>  1 file changed, 15 insertions(+), 3 deletions(-)

Acked-by: Rob Herring <robh@kernel.org> 

Re: [PATCH v6 02/12] mmc: mediatek: add support of mt2701/mt2712

[Sean Wang]

Hi, 

I've tested those patches on the bpi-r2 board [1] and so far they work
fine correctly. The below are some tests using lmdd on the board.

a. emmc with high-speed mode

reading
# lmdd of=internal if=/dev/mmcblk0p3 count=100000  fsync=1
819.2000 MB in 34.5092 secs, 23.7386 MB/sec

writing
# lmdd if=internal of=/dev/mmcblk0p3 count=100000  fsync=1
819.2000 MB in 42.9084 secs, 19.0918 MB/sec

b. sd card with Apacer 16G, high-speed speed

reading
# lmdd of=internal if=/dev/mmcblk1p1 count=100000  fsync=1             
819.2000 MB in 36.8891 secs, 22.2071 MB/sec

writing
# lmdd if=internal of=/dev/mmcblk1p1 count=100000  fsync=1
819.2000 MB in 81.7611 secs, 10.0194 MB/sec
                                                                                                       
Since mmc on mt7623 is almost identical to to mt2701, once the whole
series is being applied, I will change all nodes in dts with mt7623 to
use mt2701-mmc fallbacks instead of mt8135-mmc ones.

Tested-by: Sean Wang <sean.wang@mediatek.com>

[1] http://forum.banana-pi.org/c/Banana-Pi-BPI-R2


On Mon, 2017-10-16 at 09:46 +0800, Chaotian Jing wrote:
> mt2701/mt2712 has 12bit clock div, which is not compatible with
> mt8135/mt8173. and, some additional features will be added in
> mt2701/mt2712, so that need distinguish it by comatibale name.
> 
> Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
> ---
>  drivers/mmc/host/mtk-sd.c | 82 +++++++++++++++++++++++++++++++++++++++--------
>  1 file changed, 69 insertions(+), 13 deletions(-)
> 
> diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
> index 267f7ab..643c795 100644
> --- a/drivers/mmc/host/mtk-sd.c
> +++ b/drivers/mmc/host/mtk-sd.c
> @@ -95,6 +95,9 @@
>  #define MSDC_CFG_CKDIV          (0xff << 8)	/* RW */
>  #define MSDC_CFG_CKMOD          (0x3 << 16)	/* RW */
>  #define MSDC_CFG_HS400_CK_MODE  (0x1 << 18)	/* RW */
> +#define MSDC_CFG_HS400_CK_MODE_EXTRA  (0x1 << 22)	/* RW */
> +#define MSDC_CFG_CKDIV_EXTRA    (0xfff << 8)	/* RW */
> +#define MSDC_CFG_CKMOD_EXTRA    (0x3 << 20)	/* RW */
>  
>  /* MSDC_IOCON mask */
>  #define MSDC_IOCON_SDR104CKS    (0x1 << 0)	/* RW */
> @@ -295,6 +298,10 @@ struct msdc_save_para {
>  	u32 emmc50_cfg0;
>  };
>  
> +struct mtk_mmc_compatible {
> +	u8 clk_div_bits;
> +};
> +
>  struct msdc_tune_para {
>  	u32 iocon;
>  	u32 pad_tune;
> @@ -309,6 +316,7 @@ struct msdc_delay_phase {
>  
>  struct msdc_host {
>  	struct device *dev;
> +	const struct mtk_mmc_compatible *dev_comp;
>  	struct mmc_host *mmc;	/* mmc structure */
>  	int cmd_rsp;
>  
> @@ -350,6 +358,31 @@ struct msdc_host {
>  	struct msdc_tune_para saved_tune_para; /* tune result of CMD21/CMD19 */
>  };
>  
> +static const struct mtk_mmc_compatible mt8135_compat = {
> +	.clk_div_bits = 8,
> +};
> +
> +static const struct mtk_mmc_compatible mt8173_compat = {
> +	.clk_div_bits = 8,
> +};
> +
> +static const struct mtk_mmc_compatible mt2701_compat = {
> +	.clk_div_bits = 12,
> +};
> +
> +static const struct mtk_mmc_compatible mt2712_compat = {
> +	.clk_div_bits = 12,
> +};
> +
> +static const struct of_device_id msdc_of_ids[] = {
> +	{ .compatible = "mediatek,mt8135-mmc", .data = &mt8135_compat},
> +	{ .compatible = "mediatek,mt8173-mmc", .data = &mt8173_compat},
> +	{ .compatible = "mediatek,mt2701-mmc", .data = &mt2701_compat},
> +	{ .compatible = "mediatek,mt2712-mmc", .data = &mt2712_compat},
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, msdc_of_ids);
> +
>  static void sdr_set_bits(void __iomem *reg, u32 bs)
>  {
>  	u32 val = readl(reg);
> @@ -509,7 +542,12 @@ static void msdc_set_timeout(struct msdc_host *host, u32 ns, u32 clks)
>  		timeout = (ns + clk_ns - 1) / clk_ns + clks;
>  		/* in 1048576 sclk cycle unit */
>  		timeout = (timeout + (0x1 << 20) - 1) >> 20;
> -		sdr_get_field(host->base + MSDC_CFG, MSDC_CFG_CKMOD, &mode);
> +		if (host->dev_comp->clk_div_bits == 8)
> +			sdr_get_field(host->base + MSDC_CFG,
> +				      MSDC_CFG_CKMOD, &mode);
> +		else
> +			sdr_get_field(host->base + MSDC_CFG,
> +				      MSDC_CFG_CKMOD_EXTRA, &mode);
>  		/*DDR mode will double the clk cycles for data timeout */
>  		timeout = mode >= 2 ? timeout * 2 : timeout;
>  		timeout = timeout > 1 ? timeout - 1 : 0;
> @@ -548,7 +586,11 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
>  
>  	flags = readl(host->base + MSDC_INTEN);
>  	sdr_clr_bits(host->base + MSDC_INTEN, flags);
> -	sdr_clr_bits(host->base + MSDC_CFG, MSDC_CFG_HS400_CK_MODE);
> +	if (host->dev_comp->clk_div_bits == 8)
> +		sdr_clr_bits(host->base + MSDC_CFG, MSDC_CFG_HS400_CK_MODE);
> +	else
> +		sdr_clr_bits(host->base + MSDC_CFG,
> +			     MSDC_CFG_HS400_CK_MODE_EXTRA);
>  	if (timing == MMC_TIMING_UHS_DDR50 ||
>  	    timing == MMC_TIMING_MMC_DDR52 ||
>  	    timing == MMC_TIMING_MMC_HS400) {
> @@ -568,8 +610,12 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
>  
>  		if (timing == MMC_TIMING_MMC_HS400 &&
>  		    hz >= (host->src_clk_freq >> 1)) {
> -			sdr_set_bits(host->base + MSDC_CFG,
> -				     MSDC_CFG_HS400_CK_MODE);
> +			if (host->dev_comp->clk_div_bits == 8)
> +				sdr_set_bits(host->base + MSDC_CFG,
> +					     MSDC_CFG_HS400_CK_MODE);
> +			else
> +				sdr_set_bits(host->base + MSDC_CFG,
> +					     MSDC_CFG_HS400_CK_MODE_EXTRA);
>  			sclk = host->src_clk_freq >> 1;
>  			div = 0; /* div is ignore when bit18 is set */
>  		}
> @@ -587,8 +633,15 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
>  			sclk = (host->src_clk_freq >> 2) / div;
>  		}
>  	}
> -	sdr_set_field(host->base + MSDC_CFG, MSDC_CFG_CKMOD | MSDC_CFG_CKDIV,
> -		      (mode << 8) | div);
> +	if (host->dev_comp->clk_div_bits == 8)
> +		sdr_set_field(host->base + MSDC_CFG,
> +			      MSDC_CFG_CKMOD | MSDC_CFG_CKDIV,
> +			      (mode << 8) | div);
> +	else
> +		sdr_set_field(host->base + MSDC_CFG,
> +			      MSDC_CFG_CKMOD_EXTRA | MSDC_CFG_CKDIV_EXTRA,
> +			      (mode << 12) | div);
> +
>  	sdr_set_bits(host->base + MSDC_CFG, MSDC_CFG_CKPDN);
>  	while (!(readl(host->base + MSDC_CFG) & MSDC_CFG_CKSTB))
>  		cpu_relax();
> @@ -1617,12 +1670,17 @@ static int msdc_drv_probe(struct platform_device *pdev)
>  	struct mmc_host *mmc;
>  	struct msdc_host *host;
>  	struct resource *res;
> +	const struct of_device_id *of_id;
>  	int ret;
>  
>  	if (!pdev->dev.of_node) {
>  		dev_err(&pdev->dev, "No DT found\n");
>  		return -EINVAL;
>  	}
> +
> +	of_id = of_match_node(msdc_of_ids, pdev->dev.of_node);
> +	if (!of_id)
> +		return -EINVAL;
>  	/* Allocate MMC host for this device */
>  	mmc = mmc_alloc_host(sizeof(struct msdc_host), &pdev->dev);
>  	if (!mmc)
> @@ -1686,11 +1744,15 @@ static int msdc_drv_probe(struct platform_device *pdev)
>  	msdc_of_property_parse(pdev, host);
>  
>  	host->dev = &pdev->dev;
> +	host->dev_comp = of_id->data;
>  	host->mmc = mmc;
>  	host->src_clk_freq = clk_get_rate(host->src_clk);
>  	/* Set host parameters to mmc */
>  	mmc->ops = &mt_msdc_ops;
> -	mmc->f_min = DIV_ROUND_UP(host->src_clk_freq, 4 * 255);
> +	if (host->dev_comp->clk_div_bits == 8)
> +		mmc->f_min = DIV_ROUND_UP(host->src_clk_freq, 4 * 255);
> +	else
> +		mmc->f_min = DIV_ROUND_UP(host->src_clk_freq, 4 * 4095);
>  
>  	mmc->caps |= MMC_CAP_ERASE | MMC_CAP_CMD23;
>  	/* MMC core transfer sizes tunable parameters */
> @@ -1839,12 +1901,6 @@ static int msdc_runtime_resume(struct device *dev)
>  	SET_RUNTIME_PM_OPS(msdc_runtime_suspend, msdc_runtime_resume, NULL)
>  };
>  
> -static const struct of_device_id msdc_of_ids[] = {
> -	{   .compatible = "mediatek,mt8135-mmc", },
> -	{}
> -};
> -MODULE_DEVICE_TABLE(of, msdc_of_ids);
> -
>  static struct platform_driver mt_msdc_driver = {
>  	.probe = msdc_drv_probe,
>  	.remove = msdc_drv_remove,

Re: [PATCH v6 03/12] arm64: dts: mt8173: remove "mediatek,mt8135-mmc" from mmc nodes

[Ulf Hansson]

On 16 October 2017 at 03:46, Chaotian Jing <chaotian.jing@mediatek.com> wrote:
> devicetree bindings has been updated to support multi-platforms,
> so that each platform has its owns compatible name.
> And, this compatible name may used in driver to distinguish with
> other platform.
>
> Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>

Matthias, do you intend to pick this? Else I can do it with your ack...

Kind regards
Uffe

> ---
>  arch/arm64/boot/dts/mediatek/mt8173.dtsi | 12 ++++--------
>  1 file changed, 4 insertions(+), 8 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> index b99a273..26396ef 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> @@ -682,8 +682,7 @@
>                 };
>
>                 mmc0: mmc@11230000 {
> -                       compatible = "mediatek,mt8173-mmc",
> -                                    "mediatek,mt8135-mmc";
> +                       compatible = "mediatek,mt8173-mmc";
>                         reg = <0 0x11230000 0 0x1000>;
>                         interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_LOW>;
>                         clocks = <&pericfg CLK_PERI_MSDC30_0>,
> @@ -693,8 +692,7 @@
>                 };
>
>                 mmc1: mmc@11240000 {
> -                       compatible = "mediatek,mt8173-mmc",
> -                                    "mediatek,mt8135-mmc";
> +                       compatible = "mediatek,mt8173-mmc";
>                         reg = <0 0x11240000 0 0x1000>;
>                         interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>;
>                         clocks = <&pericfg CLK_PERI_MSDC30_1>,
> @@ -704,8 +702,7 @@
>                 };
>
>                 mmc2: mmc@11250000 {
> -                       compatible = "mediatek,mt8173-mmc",
> -                                    "mediatek,mt8135-mmc";
> +                       compatible = "mediatek,mt8173-mmc";
>                         reg = <0 0x11250000 0 0x1000>;
>                         interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_LOW>;
>                         clocks = <&pericfg CLK_PERI_MSDC30_2>,
> @@ -715,8 +712,7 @@
>                 };
>
>                 mmc3: mmc@11260000 {
> -                       compatible = "mediatek,mt8173-mmc",
> -                                    "mediatek,mt8135-mmc";
> +                       compatible = "mediatek,mt8173-mmc";
>                         reg = <0 0x11260000 0 0x1000>;
>                         interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_LOW>;
>                         clocks = <&pericfg CLK_PERI_MSDC30_3>,
> --
> 1.8.1.1.dirty
>

Re: [PATCH v6 00/12] mmc: mediatek: add support of mt2701/mt2712

[Ulf Hansson]

On 16 October 2017 at 03:46, Chaotian Jing <chaotian.jing@mediatek.com> wrote:
>   This serial of patches are adding support of mt2701/mt2712.
> there are many changes and HW improvement between mt8173 and
> mt2701/mt2712, below is a list of these changes:
>   1. enlarge CLKDIV bits from 8 to 12
>   2. remove the PAD_TUNE register and add a new PAD_TUNE0 register
>   3. add data sync and async fifo feature
>   4. add busy_check feature
>   5. add stop_clk fix
>   6. add enhance_rx support
>   7. add a seperate CG of source clock
>
>   mt2712 supports full of these features, mt2701 supports part of it, and
> add a "mediatek,latch-ck" to work-around as it do not support stop-clk fix.
>
> Note: As Pinctrl/CCF are not ready now, so that current patches do not
> include DTS part.
>
> Changed vs v5:
>   based on Rob's comments, explain why MT8173 no longer compatible with
> driver that supports "mediatek,mt8135-mmc", add more clearly description
> of "mediatek,latch-ck".
>
> Changed vs v4:
>   based on Julien's comment, change the "bool pad_tune0" to "u32 pad_tune_reg".
>
> Changed vs v3:
>   based on Ulf's comments, make the bindings change to be the first patch.
>
> Changed vs v2:
>   based on Matthias's comments, merge binding file changes to one patch,
> add "hs400_tune" flag in dev_comp.
>
> Changed vs v1:
>   based on Ulf/Rob/Matthias's comments of DTS binding file, make the binding
> file clearly and fix probe issue.
>
>
> Chaotian Jing (12):
>   mmc: dt-bindings: Add reg/source_cg/latch-ck for Mediatek MMC bindings
>   mmc: mediatek: add support of mt2701/mt2712
>   arm64: dts: mt8173: remove "mediatek,mt8135-mmc" from mmc nodes
>   mmc: mediatek: make hs400_tune_response only for mt8173
>   mmc: mediatek: add pad_tune0 support
>   mmc: mediatek: add async fifo and data tune support
>   mmc: mediatek: add busy_check support
>   mmc: mediatek: add stop_clk fix and enhance_rx support
>   mmc: mediatek: add support of source_cg clock
>   mmc: mediatek: add latch-ck support
>   mmc: mediatek: improve eMMC hs400 mode read performance
>   mmc: mediatek: perfer to use rise edge latching for cmd line
>
>  Documentation/devicetree/bindings/mmc/mtk-sd.txt |  18 +-
>  arch/arm64/boot/dts/mediatek/mt8173.dtsi         |  12 +-
>  drivers/mmc/host/mtk-sd.c                        | 283 ++++++++++++++++++++---
>  3 files changed, 265 insertions(+), 48 deletions(-)
>

Thanks, applied the hole series on my next branch.

If Matthias wants to pick/ack the DT change (patch3), I either add his
ack or drop that patch from my tree.

Kind regards
Uffe

Re: [PATCH v6 03/12] arm64: dts: mt8173: remove "mediatek,mt8135-mmc" from mmc nodes

[Matthias Brugger]

On 10/25/2017 11:11 PM, Ulf Hansson wrote:
> On 16 October 2017 at 03:46, Chaotian Jing <chaotian.jing@mediatek.com> wrote:
>> devicetree bindings has been updated to support multi-platforms,
>> so that each platform has its owns compatible name.
>> And, this compatible name may used in driver to distinguish with
>> other platform.
>>
>> Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
> 
> Matthias, do you intend to pick this? Else I can do it with your ack...
> 

If it's not too late, feel free to take it. Otherwise I will queue it for the
next merge window:

Acked-by: Matthias Brugger <matthias.bgg@gmail.com>

> Kind regards
> Uffe
> 
>> ---
>>  arch/arm64/boot/dts/mediatek/mt8173.dtsi | 12 ++++--------
>>  1 file changed, 4 insertions(+), 8 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
>> index b99a273..26396ef 100644
>> --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
>> +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
>> @@ -682,8 +682,7 @@
>>                 };
>>
>>                 mmc0: mmc@11230000 {
>> -                       compatible = "mediatek,mt8173-mmc",
>> -                                    "mediatek,mt8135-mmc";
>> +                       compatible = "mediatek,mt8173-mmc";
>>                         reg = <0 0x11230000 0 0x1000>;
>>                         interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_LOW>;
>>                         clocks = <&pericfg CLK_PERI_MSDC30_0>,
>> @@ -693,8 +692,7 @@
>>                 };
>>
>>                 mmc1: mmc@11240000 {
>> -                       compatible = "mediatek,mt8173-mmc",
>> -                                    "mediatek,mt8135-mmc";
>> +                       compatible = "mediatek,mt8173-mmc";
>>                         reg = <0 0x11240000 0 0x1000>;
>>                         interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>;
>>                         clocks = <&pericfg CLK_PERI_MSDC30_1>,
>> @@ -704,8 +702,7 @@
>>                 };
>>
>>                 mmc2: mmc@11250000 {
>> -                       compatible = "mediatek,mt8173-mmc",
>> -                                    "mediatek,mt8135-mmc";
>> +                       compatible = "mediatek,mt8173-mmc";
>>                         reg = <0 0x11250000 0 0x1000>;
>>                         interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_LOW>;
>>                         clocks = <&pericfg CLK_PERI_MSDC30_2>,
>> @@ -715,8 +712,7 @@
>>                 };
>>
>>                 mmc3: mmc@11260000 {
>> -                       compatible = "mediatek,mt8173-mmc",
>> -                                    "mediatek,mt8135-mmc";
>> +                       compatible = "mediatek,mt8173-mmc";
>>                         reg = <0 0x11260000 0 0x1000>;
>>                         interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_LOW>;
>>                         clocks = <&pericfg CLK_PERI_MSDC30_3>,
>> --
>> 1.8.1.1.dirty
>>

Re: [PATCH v6 03/12] arm64: dts: mt8173: remove "mediatek,mt8135-mmc" from mmc nodes

[Ulf Hansson]

On 2 November 2017 at 12:50, Matthias Brugger <matthias.bgg@gmail.com> wrote:
>
>
> On 10/25/2017 11:11 PM, Ulf Hansson wrote:
>> On 16 October 2017 at 03:46, Chaotian Jing <chaotian.jing@mediatek.com> wrote:
>>> devicetree bindings has been updated to support multi-platforms,
>>> so that each platform has its owns compatible name.
>>> And, this compatible name may used in driver to distinguish with
>>> other platform.
>>>
>>> Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
>>
>> Matthias, do you intend to pick this? Else I can do it with your ack...
>>
>
> If it's not too late, feel free to take it. Otherwise I will queue it for the
> next merge window:
>
> Acked-by: Matthias Brugger <matthias.bgg@gmail.com>

Thanks, I have queued it up for 4.15 and will add your ack.

Kind regards
Uffe