From: Ulf Hansson <ulf.hansson@linaro.org>
To: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linus.walleij@stericsson.com,
Russell King <linux@arm.linux.org.uk>,
Chris Ball <cjb@laptop.org>,
linux-mmc@vger.kernel.org
Subject: Re: [PATCH] mmc: mmci: Allow MMCI to request channels with information acquired from DT
Date: Thu, 18 Apr 2013 10:21:14 +0200 [thread overview]
Message-ID: <CAPDyKFqHBYRRNFqKMdw4H73_o-v_sQ5ybGg3jZHqgNDg4zyB5w@mail.gmail.com> (raw)
In-Reply-To: <20130418080238.GB3137@gmail.com>
On 18 April 2013 10:02, Lee Jones <lee.jones@linaro.org> wrote:
>> I think you can further simplify this, given that in the DT case we always
>> allocate a zeroed mmci_platform_data for host->plat, so !plat cannot happen
>> when we get here.
>
> Okay, third time lucky. :)
>
> diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
> index 372e921..3260ab4 100644
> --- a/drivers/mmc/host/mmci.c
> +++ b/drivers/mmc/host/mmci.c
> @@ -298,14 +298,16 @@ static void mmci_init_sg(struct mmci_host *host, struct mmc_data *data)
> * no custom DMA interfaces are supported.
> */
> #ifdef CONFIG_DMA_ENGINE
> -static void mmci_dma_setup(struct mmci_host *host)
> +static void mmci_dma_setup(struct amba_device *dev,
> + struct mmci_host *host)
Hi Lee,
You don't need to pass the amba_device, this can be fetched from the
mmci_host. Check how other functions converts the mmci host it in this
driver.
Kind regards
Ulf Hansson
> {
> + struct device_node *np = dev->dev.of_node;
> struct mmci_platform_data *plat = host->plat;
> const char *rxname, *txname;
> dma_cap_mask_t mask;
>
> - if (!plat || !plat->dma_filter) {
> - dev_info(mmc_dev(host->mmc), "no DMA platform data\n");
> + if (!(plat->dma_filter || np)) {
> + dev_info(mmc_dev(host->mmc), "no DMA platform data or DT\n");
> return;
> }
>
> @@ -321,19 +323,21 @@ static void mmci_dma_setup(struct mmci_host *host)
> * attempt to use it bidirectionally, however if it is
> * is specified but cannot be located, DMA will be disabled.
> */
> - if (plat->dma_rx_param) {
> - host->dma_rx_channel = dma_request_channel(mask,
> - plat->dma_filter,
> - plat->dma_rx_param);
> + if (plat->dma_rx_param || np) {
> + host->dma_rx_channel = dma_request_slave_channel_compat(mask,
> + plat->dma_filter,
> + plat->dma_rx_param,
> + &dev->dev, "rx");
> /* E.g if no DMA hardware is present */
> if (!host->dma_rx_channel)
> dev_err(mmc_dev(host->mmc), "no RX DMA channel\n");
> }
>
> - if (plat->dma_tx_param) {
> - host->dma_tx_channel = dma_request_channel(mask,
> - plat->dma_filter,
> - plat->dma_tx_param);
> + if (plat->dma_tx_param || np) {
> + host->dma_tx_channel = dma_request_slave_channel_compat(mask,
> + plat->dma_filter,
> + plat->dma_tx_param,
> + &dev->dev, "tx");
> if (!host->dma_tx_channel)
> dev_warn(mmc_dev(host->mmc), "no TX DMA channel\n");
> } else {
> @@ -1538,7 +1542,7 @@ static int mmci_probe(struct amba_device *dev,
> amba_rev(dev), (unsigned long long)dev->res.start,
> dev->irq[0], dev->irq[1]);
>
> - mmci_dma_setup(host);
> + mmci_dma_setup(dev, host);
>
> pm_runtime_set_autosuspend_delay(&dev->dev, 50);
> pm_runtime_use_autosuspend(&dev->dev);
>
> --
> Lee Jones
> Linaro ST-Ericsson Landing Team Lead
> Linaro.org │ Open source software for ARM SoCs
> Follow Linaro: Facebook | Twitter | Blog
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2013-04-18 8:21 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-04-17 13:32 [PATCH] mmc: mmci: Allow MMCI to request channels with information acquired from DT Lee Jones
2013-04-17 13:50 ` Arnd Bergmann
2013-04-17 15:04 ` Lee Jones
2013-04-17 15:31 ` Arnd Bergmann
2013-04-18 8:02 ` Lee Jones
2013-04-18 8:15 ` Russell King - ARM Linux
2013-04-18 9:25 ` Arnd Bergmann
2013-04-18 9:30 ` Russell King - ARM Linux
2013-04-18 8:21 ` Ulf Hansson [this message]
2013-04-24 10:58 Lee Jones
2013-04-30 13:01 ` Linus Walleij
2013-04-30 13:12 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAPDyKFqHBYRRNFqKMdw4H73_o-v_sQ5ybGg3jZHqgNDg4zyB5w@mail.gmail.com \
--to=ulf.hansson@linaro.org \
--cc=arnd@arndb.de \
--cc=cjb@laptop.org \
--cc=lee.jones@linaro.org \
--cc=linus.walleij@stericsson.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux@arm.linux.org.uk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).