[PATCH v2 2/2] hwmon: pmbus: Add Inspur Power System power supply driver

[PATCH v2 2/2] hwmon: pmbus: Add Inspur Power System power supply driver

[John Wang]

Add the driver to monitor Inspur Power System power supplies
with hwmon over pmbus.

This driver adds sysfs attributes for additional power supply data,
including vendor, model, part_number, serial number,
firmware revision, hardware revision, and psu mode(active/standby).

Signed-off-by: John Wang <wangzqbj@inspur.com>
---
v2:
    - Fix typos in commit message
    - Invert Christmas tree
    - Configure device with sysfs attrs, not debugfs entries
    - Fix errno in fw_version_read, ENODATA to EPROTO
    - Change the print format of fw-version
    - Use sysfs_streq instead of strcmp("xxx" "\n", "xxx")
    - Document sysfs attributes
---
 Documentation/hwmon/inspur-ipsps1.rst |  79 +++++++++
 drivers/hwmon/pmbus/Kconfig           |   9 +
 drivers/hwmon/pmbus/Makefile          |   1 +
 drivers/hwmon/pmbus/inspur-ipsps.c    | 236 ++++++++++++++++++++++++++
 4 files changed, 325 insertions(+)
 create mode 100644 Documentation/hwmon/inspur-ipsps1.rst
 create mode 100644 drivers/hwmon/pmbus/inspur-ipsps.c

diff --git a/Documentation/hwmon/inspur-ipsps1.rst b/Documentation/hwmon/inspur-ipsps1.rst
new file mode 100644
index 000000000000..aa19f0ccc8b0
--- /dev/null
+++ b/Documentation/hwmon/inspur-ipsps1.rst
@@ -0,0 +1,79 @@
+Kernel driver inspur-ipsps1
+=======================
+
+Supported chips:
+
+  * Inspur Power System power supply unit
+
+Author: John Wang <wangzqbj@inspur.com>
+
+Description
+-----------
+
+This driver supports Inspur Power System power supplies. This driver
+is a client to the core PMBus driver.
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+Sysfs entries
+-------------
+
+The following attributes are supported:
+
+======================= ======================================================
+curr1_input             Measured input current
+curr1_label             "iin"
+curr1_max               Maximum current
+curr1_max_alarm         Current high alarm
+curr2_input		Measured output current in mA.
+curr2_label		"iout1"
+curr2_crit              Critical maximum current
+curr2_crit_alarm        Current critical high alarm
+curr2_max               Maximum current
+curr2_max_alarm         Current high alarm
+
+fan1_alarm		Fan 1 warning.
+fan1_fault		Fan 1 fault.
+fan1_input		Fan 1 speed in RPM.
+
+in1_alarm		Input voltage under-voltage alarm.
+in1_input		Measured input voltage in mV.
+in1_label		"vin"
+in2_input		Measured output voltage in mV.
+in2_label		"vout1"
+in2_lcrit               Critical minimum output voltage
+in2_lcrit_alarm         Output voltage critical low alarm
+in2_max                 Maximum output voltage
+in2_max_alarm           Output voltage high alarm
+in2_min                 Minimum output voltage
+in2_min_alarm           Output voltage low alarm
+
+power1_alarm		Input fault or alarm.
+power1_input		Measured input power in uW.
+power1_label		"pin"
+power1_max              Input power limit
+power2_max_alarm	Output power high alarm
+power2_max              Output power limit
+power2_input		Measured output power in uW.
+power2_label		"pout"
+
+temp[1-3]_input		Measured temperature
+temp[1-2]_max		Maximum temperature
+temp[1-3]_max_alarm	Temperature high alarm
+
+vendor                  Manufacturer name
+model                   Product model
+part_number             Product part number
+serial_number           Product serial number
+fw_version              Firmware version
+hw_version              Hardware version
+mode                    Work mode. Can be set to active or
+                        standby, when set to standby, PSU will
+                        automatically switch between standby
+                        and redundancy mode.
+======================= ======================================================
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 30751eb9550a..c09357c26b10 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -203,4 +203,13 @@ config SENSORS_ZL6100
 	  This driver can also be built as a module. If so, the module will
 	  be called zl6100.
 
+config SENSORS_INSPUR_IPSPS
+	tristate "INSPUR Power System Power Supply"
+	help
+	  If you say yes here you get hardware monitoring support for the INSPUR
+	  Power System power supply.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called inspur-ipsps.
+
 endif # PMBUS
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index 2219b9300316..fde2d10cd05c 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -23,3 +23,4 @@ obj-$(CONFIG_SENSORS_TPS53679)	+= tps53679.o
 obj-$(CONFIG_SENSORS_UCD9000)	+= ucd9000.o
 obj-$(CONFIG_SENSORS_UCD9200)	+= ucd9200.o
 obj-$(CONFIG_SENSORS_ZL6100)	+= zl6100.o
+obj-$(CONFIG_SENSORS_INSPUR_IPSPS)	+= inspur-ipsps.o
diff --git a/drivers/hwmon/pmbus/inspur-ipsps.c b/drivers/hwmon/pmbus/inspur-ipsps.c
new file mode 100644
index 000000000000..f6dd10a62aef
--- /dev/null
+++ b/drivers/hwmon/pmbus/inspur-ipsps.c
@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2019 Inspur Corp.
+ */
+
+#include <linux/debugfs.h>
+#include <linux/device.h>
+#include <linux/fs.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pmbus.h>
+#include <linux/hwmon-sysfs.h>
+
+#include "pmbus.h"
+
+#define IPSPS_REG_VENDOR_ID	0x99
+#define IPSPS_REG_MODEL		0x9A
+#define IPSPS_REG_FW_VERSION	0x9B
+#define IPSPS_REG_PN		0x9C
+#define IPSPS_REG_SN		0x9E
+#define IPSPS_REG_HW_VERSION	0xB0
+#define IPSPS_REG_MODE		0xFC
+
+#define MODE_ACTIVE		0x55
+#define MODE_STANDBY		0x0E
+#define MODE_REDUNDANCY		0x00
+
+#define MODE_ACTIVE_STRING		"active"
+#define MODE_STANDBY_STRING		"standby"
+#define MODE_REDUNDANCY_STRING		"redundancy"
+
+enum ipsps_index {
+	vendor,
+	model,
+	fw_version,
+	part_number,
+	serial_number,
+	hw_version,
+	mode,
+	num_regs,
+};
+
+static const u8 ipsps_regs[num_regs] = {
+	[vendor] = IPSPS_REG_VENDOR_ID,
+	[model] = IPSPS_REG_MODEL,
+	[fw_version] = IPSPS_REG_FW_VERSION,
+	[part_number] = IPSPS_REG_PN,
+	[serial_number] = IPSPS_REG_SN,
+	[hw_version] = IPSPS_REG_HW_VERSION,
+	[mode] = IPSPS_REG_MODE,
+};
+
+static ssize_t ipsps_string_show(struct device *dev,
+				 struct device_attribute *devattr,
+				 char *buf)
+{
+	u8 reg;
+	int rc, i;
+	char data[I2C_SMBUS_BLOCK_MAX + 1] = { 0 };
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+
+	reg = ipsps_regs[attr->index];
+	rc = i2c_smbus_read_block_data(client, reg, data);
+	if (rc < 0)
+		return rc;
+
+	for (i = 0; i < rc; i++) {
+		/* filled with printable characters, ending with # */
+		if (data[i] == '#')
+			break;
+	}
+
+	data[i] = '\0';
+
+	return snprintf(buf, PAGE_SIZE, "%s\n", data);
+}
+
+static ssize_t ipsps_fw_version_show(struct device *dev,
+				     struct device_attribute *devattr,
+				     char *buf)
+{
+	u8 reg;
+	int rc;
+	u8 data[I2C_SMBUS_BLOCK_MAX] = { 0 };
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+
+	reg = ipsps_regs[attr->index];
+	rc = i2c_smbus_read_block_data(client, reg, data);
+	if (rc < 0)
+		return rc;
+
+	if (rc != 6)
+		return -EPROTO;
+
+	return snprintf(buf, PAGE_SIZE, "%u.%02u%u-%u.%02u\n",
+			data[1], data[2]/* < 100 */, data[3]/*< 10*/,
+			data[4], data[5]/* < 100 */);
+}
+
+static ssize_t ipsps_mode_show(struct device *dev,
+			       struct device_attribute *devattr, char *buf)
+{
+	u8 reg;
+	int rc;
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+
+	reg = ipsps_regs[attr->index];
+	rc = i2c_smbus_read_byte_data(client, reg);
+	if (rc < 0)
+		return rc;
+
+	switch (rc) {
+	case MODE_ACTIVE:
+		return snprintf(buf, PAGE_SIZE, "[%s] %s %s\n",
+				MODE_ACTIVE_STRING,
+				MODE_STANDBY_STRING, MODE_REDUNDANCY_STRING);
+	case MODE_STANDBY:
+		return snprintf(buf, PAGE_SIZE, "%s [%s] %s\n",
+				MODE_ACTIVE_STRING,
+				MODE_STANDBY_STRING, MODE_REDUNDANCY_STRING);
+	case MODE_REDUNDANCY:
+		return snprintf(buf, PAGE_SIZE, "%s %s [%s]\n",
+				MODE_ACTIVE_STRING,
+				MODE_STANDBY_STRING, MODE_REDUNDANCY_STRING);
+	default:
+		return snprintf(buf, PAGE_SIZE, "unspecified\n");
+	}
+}
+
+static ssize_t ipsps_mode_store(struct device *dev,
+				struct device_attribute *devattr,
+				const char *buf, size_t count)
+{
+	u8 reg;
+	int rc;
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+
+	reg = ipsps_regs[attr->index];
+	if (sysfs_streq(MODE_STANDBY_STRING, buf)) {
+		rc = i2c_smbus_write_byte_data(client, reg,
+					       MODE_STANDBY);
+		if (rc < 0)
+			return rc;
+		return count;
+	} else if (sysfs_streq(MODE_ACTIVE_STRING, buf)) {
+		rc = i2c_smbus_write_byte_data(client, reg,
+					       MODE_ACTIVE);
+		if (rc < 0)
+			return rc;
+		return count;
+	}
+
+	return -EINVAL;
+}
+
+static SENSOR_DEVICE_ATTR_RO(vendor, ipsps_string, vendor);
+static SENSOR_DEVICE_ATTR_RO(model, ipsps_string, model);
+static SENSOR_DEVICE_ATTR_RO(part_number, ipsps_string, part_number);
+static SENSOR_DEVICE_ATTR_RO(serial_number, ipsps_string, serial_number);
+static SENSOR_DEVICE_ATTR_RO(hw_version, ipsps_string, hw_version);
+static SENSOR_DEVICE_ATTR_RO(fw_version, ipsps_fw_version, fw_version);
+static SENSOR_DEVICE_ATTR_RW(mode, ipsps_mode, mode);
+
+static struct attribute *enable_attrs[] = {
+	&sensor_dev_attr_vendor.dev_attr.attr,
+	&sensor_dev_attr_model.dev_attr.attr,
+	&sensor_dev_attr_part_number.dev_attr.attr,
+	&sensor_dev_attr_serial_number.dev_attr.attr,
+	&sensor_dev_attr_hw_version.dev_attr.attr,
+	&sensor_dev_attr_fw_version.dev_attr.attr,
+	&sensor_dev_attr_mode.dev_attr.attr,
+	NULL,
+};
+
+static const struct attribute_group enable_group = {
+	.attrs = enable_attrs,
+};
+
+static const struct attribute_group *attribute_groups[] = {
+	&enable_group,
+	NULL,
+};
+
+static struct pmbus_driver_info ipsps_info = {
+	.pages = 1,
+	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_IOUT |
+		PMBUS_HAVE_IIN | PMBUS_HAVE_POUT | PMBUS_HAVE_PIN |
+		PMBUS_HAVE_FAN12 | PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2 |
+		PMBUS_HAVE_TEMP3 | PMBUS_HAVE_STATUS_VOUT |
+		PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_STATUS_INPUT |
+		PMBUS_HAVE_STATUS_TEMP | PMBUS_HAVE_STATUS_FAN12,
+	.groups = attribute_groups,
+};
+
+static struct pmbus_platform_data ipsps_pdata = {
+	.flags = PMBUS_SKIP_STATUS_CHECK,
+};
+
+static int ipsps_probe(struct i2c_client *client,
+		       const struct i2c_device_id *id)
+{
+	client->dev.platform_data = &ipsps_pdata;
+	return pmbus_do_probe(client, id, &ipsps_info);
+}
+
+static const struct i2c_device_id ipsps_id[] = {
+	{ "inspur_ipsps1", 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, ipsps_id);
+
+static const struct of_device_id ipsps_of_match[] = {
+	{ .compatible = "inspur,ipsps1" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, ipsps_of_match);
+
+static struct i2c_driver ipsps_driver = {
+	.driver = {
+		.name = "inspur-ipsps",
+		.of_match_table = ipsps_of_match,
+	},
+	.probe = ipsps_probe,
+	.remove = pmbus_do_remove,
+	.id_table = ipsps_id,
+};
+
+module_i2c_driver(ipsps_driver);
+
+MODULE_AUTHOR("John Wang");
+MODULE_DESCRIPTION("PMBus driver for Inspur Power System power supplies");
+MODULE_LICENSE("GPL");
-- 
2.17.1

Re: [PATCH v2 2/2] hwmon: pmbus: Add Inspur Power System power supply driver

[Milton Miller II]

Around 08/10/2019 04:55AM in some time zone, John Wang wrote:
>
>Add the driver to monitor Inspur Power System power supplies
>with hwmon over pmbus.
>
>This driver adds sysfs attributes for additional power supply data,
>including vendor, model, part_number, serial number,
>firmware revision, hardware revision, and psu mode(active/standby).
>
>Signed-off-by: John Wang <wangzqbj@inspur.com>
>---
>v2:
>    - Fix typos in commit message
>    - Invert Christmas tree
>    - Configure device with sysfs attrs, not debugfs entries
>    - Fix errno in fw_version_read, ENODATA to EPROTO
>    - Change the print format of fw-version
>    - Use sysfs_streq instead of strcmp("xxx" "\n", "xxx")
>    - Document sysfs attributes
>---
> Documentation/hwmon/inspur-ipsps1.rst |  79 +++++++++
> drivers/hwmon/pmbus/Kconfig           |   9 +
> drivers/hwmon/pmbus/Makefile          |   1 +
> drivers/hwmon/pmbus/inspur-ipsps.c    | 236
>++++++++++++++++++++++++++
> 4 files changed, 325 insertions(+)
> create mode 100644 Documentation/hwmon/inspur-ipsps1.rst
> create mode 100644 drivers/hwmon/pmbus/inspur-ipsps.c
>
>diff --git a/Documentation/hwmon/inspur-ipsps1.rst
>b/Documentation/hwmon/inspur-ipsps1.rst
....
>diff --git a/drivers/hwmon/pmbus/Kconfig>b/drivers/hwmon/pmbus/Kconfig
>index 30751eb9550a..c09357c26b10 100644
>--- a/drivers/hwmon/pmbus/Kconfig
>+++ b/drivers/hwmon/pmbus/Kconfig
>@@ -203,4 +203,13 @@ config SENSORS_ZL6100
> 	  This driver can also be built as a module. If so, the module will
> 	  be called zl6100.
> 
>+config SENSORS_INSPUR_IPSPS
>+	tristate "INSPUR Power System Power Supply"

The entries in this file are sorted alphabetically.

>diff --git a/drivers/hwmon/pmbus/Makefile>b/drivers/hwmon/pmbus/Makefile
>index 2219b9300316..fde2d10cd05c 100644
>--- a/drivers/hwmon/pmbus/Makefile
>+++ b/drivers/hwmon/pmbus/Makefile
>@@ -23,3 +23,4 @@ obj-$(CONFIG_SENSORS_TPS53679)	+= tps53679.o
> obj-$(CONFIG_SENSORS_UCD9000)	+= ucd9000.o
> obj-$(CONFIG_SENSORS_UCD9200)	+= ucd9200.o
> obj-$(CONFIG_SENSORS_ZL6100)	+= zl6100.o
>+obj-$(CONFIG_SENSORS_INSPUR_IPSPS)	+= inspur-ipsps.o
>diff --git a/drivers/hwmon/pmbus/inspur-ipsps.c
>b/drivers/hwmon/pmbus/inspur-ipsps.c
>new file mode 100644
>index 000000000000..f6dd10a62aef
>--- /dev/null
>+++ b/drivers/hwmon/pmbus/inspur-ipsps.c
>@@ -0,0 +1,236 @@
>+// SPDX-License-Identifier: GPL-2.0-or-later
>+/*
>+ * Copyright 2019 Inspur Corp.
>+ */
>+
>+#include <linux/debugfs.h>
>+#include <linux/device.h>
>+#include <linux/fs.h>
>+#include <linux/i2c.h>
>+#include <linux/module.h>
>+#include <linux/pmbus.h>
>+#include <linux/hwmon-sysfs.h>
>+
>+#include "pmbus.h"
>+
>+#define IPSPS_REG_VENDOR_ID	0x99
>+#define IPSPS_REG_MODEL		0x9A
>+#define IPSPS_REG_FW_VERSION	0x9B
>+#define IPSPS_REG_PN		0x9C
>+#define IPSPS_REG_SN		0x9E
>+#define IPSPS_REG_HW_VERSION	0xB0
>+#define IPSPS_REG_MODE		0xFC
>+
>+#define MODE_ACTIVE		0x55
>+#define MODE_STANDBY		0x0E
>+#define MODE_REDUNDANCY		0x00
>+
>+#define MODE_ACTIVE_STRING		"active"
>+#define MODE_STANDBY_STRING		"standby"
>+#define MODE_REDUNDANCY_STRING		"redundancy"
>+
>+enum ipsps_index {
>+	vendor,
>+	model,
>+	fw_version,
>+	part_number,
>+	serial_number,
>+	hw_version,
>+	mode,
>+	num_regs,
>+};
>+
>+static const u8 ipsps_regs[num_regs] = {
>+	[vendor] = IPSPS_REG_VENDOR_ID,
>+	[model] = IPSPS_REG_MODEL,
>+	[fw_version] = IPSPS_REG_FW_VERSION,
>+	[part_number] = IPSPS_REG_PN,
>+	[serial_number] = IPSPS_REG_SN,
>+	[hw_version] = IPSPS_REG_HW_VERSION,
>+	[mode] = IPSPS_REG_MODE,
>+};
>+
>+static ssize_t ipsps_string_show(struct device *dev,
>+				 struct device_attribute *devattr,
>+				 char *buf)
>+{
>+	u8 reg;
>+	int rc, i;
>+	char data[I2C_SMBUS_BLOCK_MAX + 1] = { 0 };

Shouldn't need to initialize this.

>+	struct i2c_client *client = to_i2c_client(dev->parent);>+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
>+
>+	reg = ipsps_regs[attr->index];
>+	rc = i2c_smbus_read_block_data(client, reg, data);
>+	if (rc < 0)
>+		return rc;
>+
>+	for (i = 0; i < rc; i++) {
>+		/* filled with printable characters, ending with # */
>+		if (data[i] == '#')
>+			break;
>+	}

This seems to be p = memscan(data, '#', rc);

>+>+	data[i] = '\0';
>+
>+	return snprintf(buf, PAGE_SIZE, "%s\n", data);
>+}
>+
>+static ssize_t ipsps_fw_version_show(struct device *dev,
>+				     struct device_attribute *devattr,
>+				     char *buf)
>+{
>+	u8 reg;
>+	int rc;
>+	u8 data[I2C_SMBUS_BLOCK_MAX] = { 0 };
>+	struct i2c_client *client = to_i2c_client(dev->parent);
>+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
>+
>+	reg = ipsps_regs[attr->index];
>+	rc = i2c_smbus_read_block_data(client, reg, data);
>+	if (rc < 0)
>+		return rc;
>+
>+	if (rc != 6)
>+		return -EPROTO;
>+
>+	return snprintf(buf, PAGE_SIZE, "%u.%02u%u-%u.%02u\n",
>+			data[1], data[2]/* < 100 */, data[3]/*< 10*/,
>+			data[4], data[5]/* < 100 */);
>+}
>+
>+static ssize_t ipsps_mode_show(struct device *dev,
>+			       struct device_attribute *devattr, char *buf)
>+{
>+	u8 reg;
>+	int rc;
>+	struct i2c_client *client = to_i2c_client(dev->parent);
>+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
>+
>+	reg = ipsps_regs[attr->index];
>+	rc = i2c_smbus_read_byte_data(client, reg);
>+	if (rc < 0)
>+		return rc;
>+
>+	switch (rc) {
>+	case MODE_ACTIVE:
>+		return snprintf(buf, PAGE_SIZE, "[%s] %s %s\n",
>+				MODE_ACTIVE_STRING,
>+				MODE_STANDBY_STRING, MODE_REDUNDANCY_STRING);
>+	case MODE_STANDBY:
>+		return snprintf(buf, PAGE_SIZE, "%s [%s] %s\n",
>+				MODE_ACTIVE_STRING,
>+				MODE_STANDBY_STRING, MODE_REDUNDANCY_STRING);
>+	case MODE_REDUNDANCY:
>+		return snprintf(buf, PAGE_SIZE, "%s %s [%s]\n",
>+				MODE_ACTIVE_STRING,
>+				MODE_STANDBY_STRING, MODE_REDUNDANCY_STRING);
>+	default:
>+		return snprintf(buf, PAGE_SIZE, "unspecified\n");
>+	}
>+}
>+
>+static ssize_t ipsps_mode_store(struct device *dev,
>+				struct device_attribute *devattr,
>+				const char *buf, size_t count)
>+{
>+	u8 reg;
>+	int rc;
>+	struct i2c_client *client = to_i2c_client(dev->parent);
>+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
>+
>+	reg = ipsps_regs[attr->index];
>+	if (sysfs_streq(MODE_STANDBY_STRING, buf)) {
>+		rc = i2c_smbus_write_byte_data(client, reg,
>+					       MODE_STANDBY);
>+		if (rc < 0)
>+			return rc;
>+		return count;
>+	} else if (sysfs_streq(MODE_ACTIVE_STRING, buf)) {
>+		rc = i2c_smbus_write_byte_data(client, reg,
>+					       MODE_ACTIVE);
>+		if (rc < 0)
>+			return rc;
>+		return count;
>+	}
>+
>+	return -EINVAL;
>+}
>+
>+static SENSOR_DEVICE_ATTR_RO(vendor, ipsps_string, vendor);
>+static SENSOR_DEVICE_ATTR_RO(model, ipsps_string, model);
>+static SENSOR_DEVICE_ATTR_RO(part_number, ipsps_string,
>part_number);
>+static SENSOR_DEVICE_ATTR_RO(serial_number, ipsps_string,
>serial_number);
>+static SENSOR_DEVICE_ATTR_RO(hw_version, ipsps_string, hw_version);
>+static SENSOR_DEVICE_ATTR_RO(fw_version, ipsps_fw_version,
>fw_version);
>+static SENSOR_DEVICE_ATTR_RW(mode, ipsps_mode, mode);
>+
>+static struct attribute *enable_attrs[] = {
>+	&sensor_dev_attr_vendor.dev_attr.attr,
>+	&sensor_dev_attr_model.dev_attr.attr,
>+	&sensor_dev_attr_part_number.dev_attr.attr,
>+	&sensor_dev_attr_serial_number.dev_attr.attr,
>+	&sensor_dev_attr_hw_version.dev_attr.attr,
>+	&sensor_dev_attr_fw_version.dev_attr.attr,
>+	&sensor_dev_attr_mode.dev_attr.attr,
>+	NULL,
>+};
>+
>+static const struct attribute_group enable_group = {
>+	.attrs = enable_attrs,
>+};
>+
>+static const struct attribute_group *attribute_groups[] = {
>+	&enable_group,
>+	NULL,
>+};

ATTRIBUTE_GROUPS(enable);

>+
>+static struct pmbus_driver_info ipsps_info = {
>+	.pages = 1,
>+	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_IOUT |
>+		PMBUS_HAVE_IIN | PMBUS_HAVE_POUT | PMBUS_HAVE_PIN |
>+		PMBUS_HAVE_FAN12 | PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2 |
>+		PMBUS_HAVE_TEMP3 | PMBUS_HAVE_STATUS_VOUT |
>+		PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_STATUS_INPUT |
>+		PMBUS_HAVE_STATUS_TEMP | PMBUS_HAVE_STATUS_FAN12,
>+	.groups = attribute_groups,
>+};
>+
>+static struct pmbus_platform_data ipsps_pdata = {
>+	.flags = PMBUS_SKIP_STATUS_CHECK,
>+};
>+
>+static int ipsps_probe(struct i2c_client *client,
>+		       const struct i2c_device_id *id)
>+{
>+	client->dev.platform_data = &ipsps_pdata;
>+	return pmbus_do_probe(client, id, &ipsps_info);
>+}
>+
>+static const struct i2c_device_id ipsps_id[] = {
>+	{ "inspur_ipsps1", 0 },
>+	{}
>+};
>+MODULE_DEVICE_TABLE(i2c, ipsps_id);
>+
>+static const struct of_device_id ipsps_of_match[] = {
>+	{ .compatible = "inspur,ipsps1" },
>+	{}
>+};
>+MODULE_DEVICE_TABLE(of, ipsps_of_match);
>+
>+static struct i2c_driver ipsps_driver = {
>+	.driver = {
>+		.name = "inspur-ipsps",
>+		.of_match_table = ipsps_of_match,
>+	},
>+	.probe = ipsps_probe,
>+	.remove = pmbus_do_remove,
>+	.id_table = ipsps_id,
>+};
>+
>+module_i2c_driver(ipsps_driver);
>+
>+MODULE_AUTHOR("John Wang");
>+MODULE_DESCRIPTION("PMBus driver for Inspur Power System power
>supplies");
>+MODULE_LICENSE("GPL");
>-- 
>2.17.1
>
>