* SMC IrDA problem with 2.4.18
@ 2002-03-06 0:16 Pawel Kot
0 siblings, 0 replies; only message in thread
From: Pawel Kot @ 2002-03-06 0:16 UTC (permalink / raw)
To: linux-kernel, irda-users
[-- Attachment #1: Type: TEXT/PLAIN, Size: 993 bytes --]
Hi,
I'm a happy new user of the new Dell Latitude c610 for a couple of days.
The one of the remaining issues I try to deal with is irda device. I can't
get it to work under linux (kernel 2.4.18). It works under windows and
introduces as: SMS IrCC - Fast Infrared Port. So I tried it with smc
driver, but no success:
Mar 3 22:51:39 bzzzt kernel: found SMC SuperIO Chip (devid=0x0e rev=01 base=0x002e): LPC47N252
Mar 3 22:51:39 bzzzt kernel: ircc_open
Mar 3 22:51:39 bzzzt kernel: SMC IrDA Controller found
Mar 3 22:51:39 bzzzt kernel: IrCC version 2.0, firport 0x280, sirport 0x2f8 dma=3, irq=3
Mar 3 22:51:39 bzzzt kernel: irport_open()
Mar 3 22:51:39 bzzzt kernel: irport_open(), can't get iobase of 0x2f8
The same ioports/dma and irq are reported to use under windows.
Any ideas what to do?
/proc/interrupts, /proc/ioports, lspci -vvv, kernel config attached
thanks,
pkot
--
mailto:pkot@linuxnews.pl :: mailto:pkot@slackware.pl
http://kt.linuxnews.pl/ :: Kernel Traffic po polsku
[-- Attachment #2: Type: TEXT/PLAIN, Size: 531 bytes --]
#
# IrDA (infrared) support
#
CONFIG_IRDA=m
CONFIG_IRLAN=m
# CONFIG_IRNET is not set
CONFIG_IRCOMM=m
# CONFIG_IRDA_ULTRA is not set
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
CONFIG_IRDA_DEBUG=y
#
# Infrared-port device drivers
#
CONFIG_IRTTY_SIR=m
CONFIG_IRPORT_SIR=m
# CONFIG_DONGLE is not set
# CONFIG_USB_IRDA is not set
# CONFIG_NSC_FIR is not set
# CONFIG_WINBOND_FIR is not set
# CONFIG_TOSHIBA_FIR is not set
CONFIG_SMC_IRCC_FIR=m
# CONFIG_ALI_FIR is not set
# CONFIG_VLSI_FIR is not set
[-- Attachment #3: Type: TEXT/PLAIN, Size: 7273 bytes --]
00:00.0 Host bridge: Intel Corporation: Unknown device 3575 (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [40] #09 [0105]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=x1
00:01.0 PCI bridge: Intel Corporation: Unknown device 3576 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc000000-fdffffff
Prefetchable memory behind bridge: e0000000-e7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corporation: Unknown device 2482 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation: Unknown device 4541
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at bf80 [size=32]
00:1e.0 PCI bridge: Intel Corporation: Unknown device 2448 (rev 41) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=10, sec-latency=32
I/O behind bridge: 0000e000-0000ffff
Memory behind bridge: f4000000-fbffffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation: Unknown device 248c (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation: Unknown device 248a (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation: Unknown device 4541
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <unassigned> [size=8]
Region 1: I/O ports at <unassigned> [size=4]
Region 2: I/O ports at <unassigned> [size=8]
Region 3: I/O ports at <unassigned> [size=4]
Region 4: I/O ports at bfa0 [size=16]
Region 5: Memory at 10000000 (32-bit, non-prefetchable) [disabled] [size=1K]
00:1f.5 Multimedia audio controller: Intel Corporation: Unknown device 2485 (rev 01)
Subsystem: Cirrus Logic: Unknown device 5959
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc80 [size=64]
00:1f.6 Modem: Intel Corporation: Unknown device 2486 (rev 01) (prog-if 00 [Generic])
Subsystem: PCTel Inc: Unknown device 4c21
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at d400 [size=256]
Region 1: I/O ports at dc00 [size=128]
01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 4c59 (prog-if 00 [VGA])
Subsystem: Dell Computer Corporation: Unknown device 00e3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping+ SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at fcff0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 78)
Subsystem: Dell Computer Corporation: Unknown device 00e3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ec80 [size=128]
Region 1: Memory at f8fffc00 (32-bit, non-prefetchable) [size=128]
Expansion ROM at f9000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:01.0 CardBus bridge: Texas Instruments PCI1420
Subsystem: Dell Computer Corporation: Unknown device 00e3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: f4400000-f47ff000 (prefetchable)
Memory window 1: f4800000-f4bff000
I/O window 0: 0000e000-0000e0ff
I/O window 1: 0000e400-0000e4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
02:01.1 CardBus bridge: Texas Instruments PCI1420
Subsystem: Dell Computer Corporation: Unknown device 00e3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: f4c00000-f4fff000 (prefetchable)
Memory window 1: f5000000-f53ff000
I/O window 0: 0000e800-0000e8ff
I/O window 1: 0000f000-0000f0ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
[-- Attachment #4: Type: TEXT/PLAIN, Size: 415 bytes --]
CPU0
0: 246287 XT-PIC timer
1: 14214 XT-PIC keyboard
2: 0 XT-PIC cascade
11: 5211 XT-PIC Texas Instruments PCI1420, Texas Instruments PCI1420 (#2), usb-uhci, eth0
12: 3441 XT-PIC PS/2 Mouse
14: 40638 XT-PIC ide0
15: 4 XT-PIC ide1
NMI: 0
ERR: 0
[-- Attachment #5: Type: TEXT/PLAIN, Size: 963 bytes --]
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
bf80-bf9f : PCI device 8086:2482 (Intel Corp.)
bf80-bf9f : usb-uhci
bfa0-bfaf : PCI device 8086:248a (Intel Corp.)
bfa0-bfa7 : ide0
bfa8-bfaf : ide1
c000-cfff : PCI Bus #01
c000-c0ff : ATI Technologies Inc Radeon Mobility M6 LY
d400-d4ff : PCI device 8086:2486 (Intel Corp.)
d800-d8ff : Intel Corp. AC'97 Audio Controller
dc00-dc7f : PCI device 8086:2486 (Intel Corp.)
dc80-dcbf : Intel Corp. AC'97 Audio Controller
e000-ffff : PCI Bus #02
e000-e0ff : PCI CardBus #03
e400-e4ff : PCI CardBus #03
e800-e8ff : PCI CardBus #07
ec80-ecff : 3Com Corporation 3c905C-TX [Fast Etherlink]
ec80-ecff : 02:00.0
f000-f0ff : PCI CardBus #07
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2002-03-06 0:16 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-03-06 0:16 SMC IrDA problem with 2.4.18 Pawel Kot
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).