* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
@ 2006-01-14 14:20 Walt H
2006-01-14 17:09 ` Alan Stern
0 siblings, 1 reply; 32+ messages in thread
From: Walt H @ 2006-01-14 14:20 UTC (permalink / raw)
To: linux-kernel; +Cc: linux-usb-devel, dmitry.torokhov, vojtech, stern
[-- Attachment #1: Type: text/plain, Size: 1087 bytes --]
> >
> > As usual with BIOS interaction problems.
> >
>
> We'll just have to wait for another report. "Sluggish typing" report
> looks promising.
>
> -- Dmitry
Well, here you go :)
I've an AMD based SMP setup w/ Chaintech 7KDD motherboard. It's an older
board, and there are no more recent BIOS updates available for me than
what I'm running. I've tried enabling/disabling legacy USB
keyboard/mouse emulation in the BIOS with no change. I'm using a USB
mouse connected via the OHCI controller in addition to the ps/2
keyboard. If I comment out the handoff code in pci-quirks.c the
keyboard works, even after loading the USB modules. I'm running a ck
based 2.6.15 kernel BTW.
During bootup with handoff code enabled, I do see a message print when
PS/2 gets init'd, and I think it is
"i8042.c: Can't read CTR while initializing i8042", but it scrolls by
too fast so I'm not positive.
lspci and config attached. Anything else you need? Please CC replies
to me, as I'm not subscribed. I tried to CC relevant people involved,
sorry if I missed anyone. Thanks,
-Walt
[-- Attachment #2: lspci.txt --]
[-- Type: text/plain, Size: 11745 bytes --]
00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] System Controller (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: Memory at f5004000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at e400 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW+ Rate=x4
00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] AGP Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=128
Memory behind bridge: f0000000-f1ffffff
Prefetchable memory behind bridge: e0000000-efffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ISA (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE (rev 04) (prog-if 8a [Master SecP PriP])
Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at f000 [size=16]
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI (rev 03)
Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:09.0 Mass storage controller: Promise Technology, Inc. PDC20268 (Ultra100 TX2) (rev 02) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra100TX2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at d000 [size=8]
Region 1: I/O ports at d400 [size=4]
Region 2: I/O ports at d800 [size=8]
Region 3: I/O ports at dc00 [size=4]
Region 4: I/O ports at e000 [size=16]
Region 5: Memory at f5000000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at 50200000 [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] PCI (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000cfff
Memory behind bridge: f3000000-f4ffffff
Prefetchable memory behind bridge: 50000000-501fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
01:05.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti 4600] (rev a3) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 2: Memory at e8000000 (32-bit, prefetchable) [size=512K]
[virtual] Expansion ROM at e8080000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=16 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW+ Rate=x4
02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-768 [Opus] USB (rev 07) (prog-if 10 [OHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 32 (20000ns max), Cache Line Size 08
Interrupt: pin D routed to IRQ 17
Region 0: Memory at f4128000 (32-bit, non-prefetchable) [size=4K]
02:04.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 0c)
Subsystem: Intel Corporation EtherExpress PRO/100 S Desktop Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f412a000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at a000 [size=64]
Region 2: Memory at f4100000 (32-bit, non-prefetchable) [size=128K]
[virtual] Expansion ROM at 50100000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:05.0 Multimedia audio controller: Creative Labs SB Audigy (rev 03)
Subsystem: Creative Labs SB0090 Audigy Player/OEM
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at a400 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:05.1 Input device controller: Creative Labs SB Audigy MIDI/Game port (rev 03)
Subsystem: Creative Labs SB Audigy MIDI/Game Port
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at a800 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:05.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (prog-if 10 [OHCI])
Subsystem: Creative Labs SB Audigy FireWire Port
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), Cache Line Size 08
Interrupt: pin B routed to IRQ 18
Region 0: Memory at f412b000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f4120000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
02:06.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corporation EtherExpress PRO/100+ Management Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f4129000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at ac00 [size=64]
Region 2: Memory at f4000000 (32-bit, non-prefetchable) [size=1M]
[virtual] Expansion ROM at 50000000 [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:07.0 RAID bus controller: Promise Technology, Inc. PDC20276 (MBFastTrak133 Lite) (rev 01) (prog-if 85)
Subsystem: Promise Technology, Inc. MBFastTrak133 Lite (tm) Controller (RAID mode)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b000 [size=8]
Region 1: I/O ports at b400 [size=4]
Region 2: I/O ports at b800 [size=8]
Region 3: I/O ports at bc00 [size=4]
Region 4: I/O ports at c000 [size=16]
Region 5: Memory at f4124000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (250ns min, 10500ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f412c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (250ns min, 10500ns max), Cache Line Size 08
Interrupt: pin B routed to IRQ 16
Region 0: Memory at f412d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8500ns max), Cache Line Size 10
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f412e000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[-- Attachment #3: config.txt --]
[-- Type: text/plain, Size: 36893 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.15-archck1-patched
# Sat Jan 14 06:45:17 2006
#
CONFIG_X86_32=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SWAP_PREFETCH=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_CPUSETS is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_EMBEDDED=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
#
# Block layer
#
# CONFIG_LBD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_CMPXCHG64=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_TSC=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
# CONFIG_SCHED_SMT is not set
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
# CONFIG_X86_MCE_P4THERMAL is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_X86_REBOOTFIXUPS is not set
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
#
# Firmware Drivers
#
# CONFIG_EDD is not set
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_HIGHMEM=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_HIGHPTE=y
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
# CONFIG_IRQBALANCE is not set
# CONFIG_REGPARM is not set
CONFIG_SECCOMP=y
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250_NODEFAULT is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_PHYSICAL_START=0x100000
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
# CONFIG_SOFTWARE_SUSPEND is not set
CONFIG_SUSPEND_SMP=y
CONFIG_SUSPEND2_CRYPTO=y
CONFIG_SUSPEND2=y
#
# Image Storage (you need at least one writer)
#
# CONFIG_SUSPEND2_FILEWRITER is not set
CONFIG_SUSPEND2_SWAPWRITER=y
#
# General Options
#
CONFIG_SUSPEND2_DEFAULT_RESUME2=""
# CONFIG_SUSPEND2_KEEP_IMAGE is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
# CONFIG_ACPI_SLEEP_PROC_SLEEP is not set
# CONFIG_ACPI_AC is not set
# CONFIG_ACPI_BATTERY is not set
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_VIDEO=y
# CONFIG_ACPI_HOTKEY is not set
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_IBM is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_CUSTOM_DSDT_INITRD=y
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
# CONFIG_X86_PM_TIMER is not set
CONFIG_ACPI_CONTAINER=y
#
# APM (Advanced Power Management) BIOS Support
#
# CONFIG_APM is not set
#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
# CONFIG_PCIEPORTBUS is not set
# CONFIG_PCI_MSI is not set
CONFIG_PCI_LEGACY_PROC=y
# CONFIG_PCI_DEBUG is not set
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
CONFIG_HOTPLUG_CPU=y
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
CONFIG_NET_KEY=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_MULTIPLE_TABLES is not set
# CONFIG_IP_ROUTE_MULTIPATH is not set
# CONFIG_IP_ROUTE_VERBOSE is not set
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
# CONFIG_NET_IPGRE_BROADCAST is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_BRIDGE_NETFILTER=y
#
# Core Netfilter Configuration
#
# CONFIG_NETFILTER_NETLINK is not set
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
# CONFIG_IP_NF_CT_ACCT is not set
# CONFIG_IP_NF_CONNTRACK_MARK is not set
# CONFIG_IP_NF_CONNTRACK_EVENTS is not set
# CONFIG_IP_NF_CT_PROTO_SCTP is not set
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
# CONFIG_IP_NF_NETBIOS_NS is not set
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_PPTP=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_PHYSDEV=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_REALM=m
CONFIG_IP_NF_MATCH_SCTP=m
CONFIG_IP_NF_MATCH_DCCP=m
CONFIG_IP_NF_MATCH_COMMENT=m
CONFIG_IP_NF_MATCH_HASHLIMIT=m
CONFIG_IP_NF_MATCH_STRING=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_TARGET_NFQUEUE=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
# CONFIG_IP_NF_NAT_SNMP_BASIC is not set
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_NAT_PPTP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_CLASSIFY=m
CONFIG_IP_NF_TARGET_TTL=m
# CONFIG_IP_NF_RAW is not set
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
#
# Bridge: Netfilter Configuration
#
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_BRIDGE_EBT_ULOG=m
#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
CONFIG_NET_CLS_ROUTE=y
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
#
# Connector - unified userspace <-> kernelspace linker
#
CONFIG_CONNECTOR=m
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set
#
# Protocols
#
CONFIG_PNPACPI=y
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_INITRD=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_IDE_TASK_IOCTL=y
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_OFFBOARD=y
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_CS5535 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
CONFIG_BLK_DEV_PDC202XX_NEW=y
CONFIG_PDC202XX_FORCE=y
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_IVB=y
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=m
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
#
# SCSI Transport Attributes
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=m
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA24XX is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
# CONFIG_MD_LINEAR is not set
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
# CONFIG_MD_RAID10 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_MD_RAID6 is not set
CONFIG_MD_MULTIPATH=y
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=m
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
# CONFIG_DM_ZERO is not set
# CONFIG_DM_MULTIPATH is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=m
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set
CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
# CONFIG_IEEE1394_EXPORT_FULL_API is not set
#
# Device Drivers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=m
#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
CONFIG_IEEE1394_SBP2_PHYS_DMA=y
# CONFIG_IEEE1394_ETH1394 is not set
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
CONFIG_IEEE1394_CMP=m
CONFIG_IEEE1394_AMDTP=m
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_BONDING=m
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_NET_SB1000 is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# PHY device support
#
# CONFIG_PHYLIB is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
CONFIG_E100=m
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
# CONFIG_SLIP_MODE_SLIP6 is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=y
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
# CONFIG_INPUT_WISTRON_BTNS is not set
# CONFIG_INPUT_UINPUT is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=m
CONFIG_SERIAL_8250_ACPI=y
CONFIG_SERIAL_8250_NR_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=m
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
CONFIG_NVRAM=y
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_AGP is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
CONFIG_RAW_DRIVER=m
CONFIG_MAX_RAW_DEVS=256
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
# CONFIG_HANGCHECK_TIMER is not set
#
# TPM devices
#
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m
#
# I2C Algorithms
#
# CONFIG_I2C_ALGOBIT is not set
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
CONFIG_I2C_AMD756=m
# CONFIG_I2C_AMD756_S4882 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_ISA=m
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=m
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_RTC_X1205_I2C is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
CONFIG_SENSORS_IT87=m
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_HDAPS is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Misc devices
#
# CONFIG_IBM_ASM is not set
#
# Multimedia Capabilities Port drivers
#
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_MACMODES is not set
CONFIG_FB_MODE_HELPERS=y
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
CONFIG_FB_VESA_STD=y
# CONFIG_FB_VESA_TNG is not set
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_I810 is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_CYBLA is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_7x14 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
CONFIG_FB_SPLASH=y
#
# Sound
#
CONFIG_SOUND=y
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_AC97_BUS=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
CONFIG_SND_GENERIC_DRIVER=y
#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m
#
# PCI devices
#
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
CONFIG_SND_EMU10K1=m
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_HDA_INTEL is not set
#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_EHCI_SPLIT_ISO is not set
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
#
# USB Device Class drivers
#
# CONFIG_OBSOLETE_OSS_USB_DRIVER is not set
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=m
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
#
# USB Input Devices
#
CONFIG_USB_HID=m
CONFIG_USB_HID_MOUSE_POLLING_INTERVAL=10
CONFIG_USB_HIDINPUT=y
CONFIG_HID_FF=y
CONFIG_HID_PID=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_THRUSTMASTER_FF is not set
CONFIG_USB_HIDDEV=y
#
# USB HID Boot Protocol drivers
#
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_ACECAD is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_ITMTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
#
# Video4Linux support is needed for USB Multimedia device support
#
#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# USB port drivers
#
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TEST is not set
#
# USB DSL modem support
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set
#
# SN Devices
#
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISER4_FS=m
# CONFIG_REISER4_DEBUG is not set
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_REISERFS_FS_XATTR is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_QUOTA=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=m
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
# CONFIG_UNION_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="cp437"
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
CONFIG_CIFS_XATTR=y
CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
CONFIG_CODA_FS=m
# CONFIG_CODA_FS_OLD_API is not set
# CONFIG_AFS_FS is not set
# CONFIG_SH_FS is not set
# CONFIG_9P_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=m
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
#
# Instrumentation Support
#
# CONFIG_PROFILING is not set
# CONFIG_KPROBES is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_LOG_BUF_SHIFT=19
# CONFIG_DETECT_SOFTLOCKUP is not set
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_EARLY_PRINTK is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES_586=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_DEFLATE=m
# CONFIG_CRYPTO_LZF is not set
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
CONFIG_CRYPTO_TEST=m
#
# Hardware crypto devices
#
# CONFIG_CRYPTO_DEV_PADLOCK is not set
#
# Library routines
#
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_DYN_PAGEFLAGS=y
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-14 14:20 PROBLEM: PS/2 keyboard does not work with 2.6.15 Walt H
@ 2006-01-14 17:09 ` Alan Stern
2006-01-14 19:27 ` Walt H
0 siblings, 1 reply; 32+ messages in thread
From: Alan Stern @ 2006-01-14 17:09 UTC (permalink / raw)
To: Walt H; +Cc: linux-kernel, linux-usb-devel, dmitry.torokhov, vojtech
On Sat, 14 Jan 2006, Walt H wrote:
> I've an AMD based SMP setup w/ Chaintech 7KDD motherboard. It's an older
> board, and there are no more recent BIOS updates available for me than
> what I'm running. I've tried enabling/disabling legacy USB
> keyboard/mouse emulation in the BIOS with no change. I'm using a USB
> mouse connected via the OHCI controller in addition to the ps/2
> keyboard. If I comment out the handoff code in pci-quirks.c the
> keyboard works, even after loading the USB modules. I'm running a ck
> based 2.6.15 kernel BTW.
>
> During bootup with handoff code enabled, I do see a message print when
> PS/2 gets init'd, and I think it is
> "i8042.c: Can't read CTR while initializing i8042", but it scrolls by
> too fast so I'm not positive.
>
> lspci and config attached. Anything else you need? Please CC replies
> to me, as I'm not subscribed. I tried to CC relevant people involved,
> sorry if I missed anyone. Thanks,
What happens if you comment out only the OHCI part of the hand-off code,
or only the EHCI part?
Check dmesg to see exactly what that i8042 message says. Are there any
lines reporting handoff problems in ohci-hcd or ehci-hcd?
Alan Stern
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-14 17:09 ` Alan Stern
@ 2006-01-14 19:27 ` Walt H
2006-01-15 15:45 ` Alan Stern
0 siblings, 1 reply; 32+ messages in thread
From: Walt H @ 2006-01-14 19:27 UTC (permalink / raw)
To: Alan Stern; +Cc: linux-kernel, linux-usb-devel, dmitry.torokhov, vojtech
Alan Stern wrote:
> On Sat, 14 Jan 2006, Walt H wrote:
>
> > I've an AMD based SMP setup w/ Chaintech 7KDD motherboard. It's an
> > older board, and there are no more recent BIOS updates available
> > for me than what I'm running. I've tried enabling/disabling legacy
> > USB keyboard/mouse emulation in the BIOS with no change. I'm using
> > a USB mouse connected via the OHCI controller in addition to the
> > ps/2 keyboard. If I comment out the handoff code in pci-quirks.c
> > the keyboard works, even after loading the USB modules. I'm running
> > a ck based 2.6.15 kernel BTW.
> >
> > During bootup with handoff code enabled, I do see a message print
> > when PS/2 gets init'd, and I think it is "i8042.c: Can't read CTR
> > while initializing i8042", but it scrolls by too fast so I'm not
> > positive.
> >
> > lspci and config attached. Anything else you need? Please CC
> > replies to me, as I'm not subscribed. I tried to CC relevant
> > people involved, sorry if I missed anyone. Thanks,
>
>
> What happens if you comment out only the OHCI part of the hand-off
> code, or only the EHCI part?
>
> Check dmesg to see exactly what that i8042 message says. Are there
> any lines reporting handoff problems in ohci-hcd or ehci-hcd?
>
> Alan Stern
>
>
OK. No lines reporting handoff problems in any of the boots. The only
boot in which I still have a keyboard is when I comment out the OHCI
handoff. I saved dmesg's of all boots, and ran diffs against them. The
uncommented handoffs and the EHCI commented handoff are essentially the
same (where the OHCI handoff code still executes in both). The relevant
(diff'd) sections are:
@@ -153,3 +153,2 @@
-i8042.c: Can't read CTR while initializing i8042.
-pnp: Device 00:09 does not supported disabling.
-pnp: Device 00:08 does not supported disabling.
+serio: i8042 AUX port at 0x60,0x64 irq 12
+serio: i8042 KBD port at 0x60,0x64 irq 1
@@ -219,0 +219 @@
+input: AT Translated Set 2 keyboard as /class/input/input0
@@ -234,0 +235 @@
+input: PS/2 Generic Mouse as /class/input/input1
@@ -268 +269 @@
-input: Logitech USB Mouse as /class/input/input0
+input: Logitech USB Mouse as /class/input/input2
Hope that helps,
-Walt
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-14 19:27 ` Walt H
@ 2006-01-15 15:45 ` Alan Stern
0 siblings, 0 replies; 32+ messages in thread
From: Alan Stern @ 2006-01-15 15:45 UTC (permalink / raw)
To: Walt H
Cc: David Brownell, linux-kernel, USB development list,
dmitry.torokhov, vojtech
On Sat, 14 Jan 2006, Walt H wrote:
> OK. No lines reporting handoff problems in any of the boots. The only
> boot in which I still have a keyboard is when I comment out the OHCI
> handoff. I saved dmesg's of all boots, and ran diffs against them. The
> uncommented handoffs and the EHCI commented handoff are essentially the
> same (where the OHCI handoff code still executes in both). The relevant
> (diff'd) sections are:
>
> @@ -153,3 +153,2 @@
> -i8042.c: Can't read CTR while initializing i8042.
> -pnp: Device 00:09 does not supported disabling.
> -pnp: Device 00:08 does not supported disabling.
> +serio: i8042 AUX port at 0x60,0x64 irq 12
> +serio: i8042 KBD port at 0x60,0x64 irq 1
> @@ -219,0 +219 @@
> +input: AT Translated Set 2 keyboard as /class/input/input0
> @@ -234,0 +235 @@
> +input: PS/2 Generic Mouse as /class/input/input1
> @@ -268 +269 @@
> -input: Logitech USB Mouse as /class/input/input0
> +input: Logitech USB Mouse as /class/input/input2
>
> Hope that helps,
That's good; you've narrowed it down to the OHCI handoff.
Now try editing the quirk_usb_handoff_ohci() routine. There's the section
enclosed in "#ifndef __hppa__" and the two writel() calls after it. Add
printk statements to see which writes are taking place, try commenting out
some of the writes -- in general, see what makes a difference.
Unfortunately I can't give you any detailed suggestions because I don't
know how the hardware is supposed to work.
Alan Stern
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-09 17:54 ` Dmitry Torokhov
2006-01-09 20:08 ` Martin Bretschneider
@ 2006-02-04 7:01 ` mahesh
1 sibling, 0 replies; 32+ messages in thread
From: mahesh @ 2006-02-04 7:01 UTC (permalink / raw)
To: linux-kernel
Dmitry Torokhov <dmitry.torokhov <at> gmail.com> writes:
On 1/9/06, Alan Stern <stern <at> rowland.harvard.edu> wrote:
> On Mon, 9 Jan 2006, Dmitry Torokhov wrote:
>
> > > It would be nice to know which part of the usb-handoff code causes the
> > > problem.
> >
> > Well, it's not handoff code causing problems per se, it's just that it
> > does not look like it performs handoff. If it did then disabling USB
> > legacy emulation in BIOS would have no effect, right?
>
> On the other hand, if the BIOS worked correctly then the ps/2 port would
> have no problems regardless of whether USB legacy emulation was on or off.
> Given that the keyboard works during bootup, I see only two possibilities:
>
> The USB handoff code somehow causes the BIOS to mess up the
> state of the 8042;
>
> The 8042 driver interacts badly with the firmware when USB
> legacy emulation is on, and the USB handoff code doesn't
> successfully turn off legacy emulation.
>
> My earlier suggestion was an attempt to test the first possibility. The
> second is harder to test because it implies problems in both the 8042
> driver and the USB handoff code.
>
My experience is that USB legacy emulation in BIOS + ACPI works as
long as you do not touch it and gets terribly confused if someone
tries to actually use i8042 (like enable active multiplexing mode with
4 AUX ports). As soon as BIOS takes its dirty hands off i8042
everything works fine.
The problem it seems that when usb-handoff code was moved from pci
quirks and enabled inconditionally something happened so it stopped
doing handoff.
Dmitry
hi
I experienced same problem, but after complilng latest kernel the problem is
rectified. So I think problem with kernel 2.6.11,13 ..could be rectified by
compiling with a higher version of kernel.
regd
mahesh
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-11 16:01 ` Jan Rekorajski
@ 2006-01-11 19:57 ` Pete Zaitcev
0 siblings, 0 replies; 32+ messages in thread
From: Pete Zaitcev @ 2006-01-11 19:57 UTC (permalink / raw)
To: Jan Rekorajski
Cc: stern, linux-kernel, vojtech, mailing-lists-mmv, jengelh,
linux-usb-devel, gregkh, nouser, zaitcev
On Wed, 11 Jan 2006 17:01:20 +0100, Jan Rekorajski <baggins@sith.mimuw.edu.pl> wrote:
> > > This happens on Dell Precision 380, x86_64 kernel with SMP/HT, no options
> > > on kernel command line, same kernel .config (modulo make oldconfig).
> > > I tried all solutions I found on google, none works (beside connecting
> > > USB keyboard or disabling USB in BIOS).
> >
> > Assuming your BIOS isn't totally out-of-date, what happens if you try
> > turning off the usb-handoff code and preventing the *hci-hcd.ko drivers
> > from loading, as described ealier in this thread?
>
> Wrong assumption, my BIOS was totally out-of-date. After upgrading to
> A04 the problem went away and now everything works fine.
Very good. I suggested this because the PW 380 is a poster child of the
buggy BIOS, and also of industry involvement: Dell fixed the problems
for us. Buy a beer for Matt Domsch.
Here's the original RHEL bug (do not add silly comments or I'll make
it private):
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=165749
Notice that the bug deals with broken sharing between EHCI and its
companion controller. This is also something a BIOS breaks often.
But you should've seen wild theories people posted about it to Ubuntu
forums, they just crack me up.
-- Pete
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-11 15:26 ` Alan Stern
@ 2006-01-11 16:01 ` Jan Rekorajski
2006-01-11 19:57 ` Pete Zaitcev
0 siblings, 1 reply; 32+ messages in thread
From: Jan Rekorajski @ 2006-01-11 16:01 UTC (permalink / raw)
To: Alan Stern
Cc: linux-kernel, Vojtech Pavlik, Martin Bretschneider,
dtor_core @ ameritech. net Jan Engelhardt, linux-usb-devel,
Greg KH, Leonid
On Wed, 11 Jan 2006, Alan Stern wrote:
> On Wed, 11 Jan 2006, Jan Rekorajski wrote:
>
> > On Tue, 10 Jan 2006, Dmitry Torokhov wrote:
> >
> > > We'll just have to wait for another report. "Sluggish typing" report
> > > looks promising.
> >
> > With 2.6.14.6:
> >
> > serio: i8042 AUX port at 0x60,0x64 irq 12
> > serio: i8042 KBD port at 0x60,0x64 irq 1
> >
> > and my keyboard works.
> >
> > with 2.6.15:
> >
> > i8042.c: Can't read CTR while initializing i8042.
> >
> > and no PS/2 keyboard.
> >
> > This happens on Dell Precision 380, x86_64 kernel with SMP/HT, no options
> > on kernel command line, same kernel .config (modulo make oldconfig).
> > I tried all solutions I found on google, none works (beside connecting
> > USB keyboard or disabling USB in BIOS).
>
> Assuming your BIOS isn't totally out-of-date, what happens if you try
> turning off the usb-handoff code and preventing the *hci-hcd.ko drivers
> from loading, as described ealier in this thread?
Wrong assumption, my BIOS was totally out-of-date. After upgrading to
A04 the problem went away and now everything works fine.
Jan
--
Jan Rękorajski | ALL SUSPECTS ARE GUILTY. PERIOD!
baggins<at>mimuw.edu.pl | OTHERWISE THEY WOULDN'T BE SUSPECTS, WOULD THEY?
BOFH, MANIAC | -- TROOPS by Kevin Rubio
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-11 0:01 ` Jan Rekorajski
2006-01-11 0:19 ` Pete Zaitcev
@ 2006-01-11 15:26 ` Alan Stern
2006-01-11 16:01 ` Jan Rekorajski
1 sibling, 1 reply; 32+ messages in thread
From: Alan Stern @ 2006-01-11 15:26 UTC (permalink / raw)
To: Jan Rekorajski
Cc: linux-kernel, Vojtech Pavlik, Martin Bretschneider,
dtor_core @ ameritech. net Jan Engelhardt, linux-usb-devel,
Greg KH, Leonid
On Wed, 11 Jan 2006, Jan Rekorajski wrote:
> On Tue, 10 Jan 2006, Dmitry Torokhov wrote:
>
> > We'll just have to wait for another report. "Sluggish typing" report
> > looks promising.
>
> With 2.6.14.6:
>
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
>
> and my keyboard works.
>
> with 2.6.15:
>
> i8042.c: Can't read CTR while initializing i8042.
>
> and no PS/2 keyboard.
>
> This happens on Dell Precision 380, x86_64 kernel with SMP/HT, no options
> on kernel command line, same kernel .config (modulo make oldconfig).
> I tried all solutions I found on google, none works (beside connecting
> USB keyboard or disabling USB in BIOS).
Assuming your BIOS isn't totally out-of-date, what happens if you try
turning off the usb-handoff code and preventing the *hci-hcd.ko drivers
from loading, as described ealier in this thread?
If your keyboard works in that state, what happens when you disable
the handoff code and driver for each one of the drivers, alone?
Alan Stern
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
[not found] ` <d120d5000601101425g576f8fd3kc9de80a4b320c3bf@mail.gmail.com>
@ 2006-01-11 2:45 ` Dave Neuer
0 siblings, 0 replies; 32+ messages in thread
From: Dave Neuer @ 2006-01-11 2:45 UTC (permalink / raw)
To: dtor_core, linux-kernel
On 1/10/06, Dmitry Torokhov <dmitry.torokhov@gmail.com> wrote:
> On 1/10/06, Dave Neuer <mr.fred.smoothie@pobox.com> wrote:
> > On 1/10/06, Dmitry Torokhov <dmitry.torokhov@gmail.com> wrote:
> > <snip>
> > > Yes, I think it is related because as soon as USB is fully initialized
> > > PS/2 starts working as well. Look for USB-related options in your BIOS
> > > and also try 2.6.15 and please post your result. Don't upgrade your
> > > BIOS yet ;)
> > >
> > > Thanks!
> >
> > I don't even think that there is a BIOS update for my now
> > 3-or-4-year-old MB which would fix this; it appears to be a very
> > poorly supported part. Gigabyte sucks, IMO.
> >
> > Anyway, I'll give 2.6.15 a try tonight and get back to you. Just to be
> > clear; you want me to check booting w/
> >
> > 1) USB enabled and no tricks
> > 2) USB mouse support disabled / USB disabled
> > 3) USB enabled w/ boot param "i8042.noacpi=1"
> > 4) The normal trick I outlined above, if none of the above work?
> >
>
> I am mostly interested in 1 and 2. I expect 1 fail and 2 succeed.
>
> --
> Dmitry
OK. Prior to trying this, I'd also upgraded udev to 0.79.
Now, on 2.6.14-rt2, PS/2 keyboard works, mouse doesn't if USB is
enabled in the BIOS, regardless of whether or not usb-handoff is
specified on the kernel commandline. However, my "load USB host
controller driver, unplug and re-plug the PS/2 mouse" trick no longer
works on 2.6.14-rt2 -- the only difference I can see being having
upgraded to udev 0.79.
On vanilla 2.6.15, neither PS/2 keyboard nor PS/2 mouse work unless
USB is disabled in the BIOS.
MB is a Gigabyte GA-7DPXDW-P (F5) w/ dual Athlon MP 1900's, BIOS says
it's Award 6.00 something.
2.6.15 .config and lspci -vv output follow (2.6.14-rt2 .config is
largely the same as 2.6.15, minus RT-stuff):
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.15
# Thu Jan 5 00:04:14 2006
#
CONFIG_X86_32=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_CPUSETS is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
#
# Block layer
#
# CONFIG_LBD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_AS is not set
CONFIG_IOSCHED_DEADLINE=y
# CONFIG_IOSCHED_CFQ is not set
# CONFIG_DEFAULT_AS is not set
CONFIG_DEFAULT_DEADLINE=y
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="deadline"
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_CMPXCHG64=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_TSC=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
# CONFIG_SCHED_SMT is not set
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
# CONFIG_X86_MCE is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
CONFIG_X86_REBOOTFIXUPS=y
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
#
# Firmware Drivers
#
# CONFIG_EDD is not set
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_HIGHMEM=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
CONFIG_IRQBALANCE=y
CONFIG_REGPARM=y
CONFIG_SECCOMP=y
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_PHYSICAL_START=0x100000
# CONFIG_KEXEC is not set
#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_AC=m
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_VIDEO=m
# CONFIG_ACPI_HOTKEY is not set
CONFIG_ACPI_FAN=m
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_THERMAL=m
CONFIG_ACPI_ASUS=m
CONFIG_ACPI_IBM=m
CONFIG_ACPI_TOSHIBA=m
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=m
#
# APM (Advanced Power Management) BIOS Support
#
CONFIG_APM=m
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
CONFIG_APM_DO_ENABLE=y
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_RTC_IS_GMT is not set
# CONFIG_APM_ALLOW_INTS is not set
CONFIG_APM_REAL_MODE_POWER_OFF=y
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=m
# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=m
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=m
CONFIG_X86_POWERNOW_K6=m
CONFIG_X86_POWERNOW_K7=m
CONFIG_X86_POWERNOW_K7_ACPI=y
CONFIG_X86_POWERNOW_K8=m
CONFIG_X86_POWERNOW_K8_ACPI=y
CONFIG_X86_GX_SUSPMOD=m
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
# CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE is not set
CONFIG_X86_SPEEDSTEP_ICH=m
CONFIG_X86_SPEEDSTEP_SMI=m
CONFIG_X86_P4_CLOCKMOD=m
CONFIG_X86_CPUFREQ_NFORCE2=m
CONFIG_X86_LONGRUN=m
CONFIG_X86_LONGHAUL=m
#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
CONFIG_X86_SPEEDSTEP_LIB=m
# CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCIEPORTBUS=y
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_LEGACY_PROC is not set
# CONFIG_PCI_DEBUG is not set
CONFIG_ISA_DMA_API=y
CONFIG_ISA=y
CONFIG_EISA=y
CONFIG_EISA_VLB_PRIMING=y
CONFIG_EISA_PCI_EISA=y
CONFIG_EISA_VIRTUAL_ROOT=y
# CONFIG_EISA_NAMES is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
# CONFIG_HOTPLUG_CPU is not set
#
# PCCARD (PCMCIA/CardBus) support
#
CONFIG_PCCARD=m
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=m
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_PCMCIA_IOCTL=y
CONFIG_CARDBUS=y
#
# PC-card bridges
#
CONFIG_YENTA=m
CONFIG_PD6729=m
CONFIG_I82092=m
CONFIG_I82365=m
CONFIG_TCIC=m
CONFIG_PCMCIA_PROBE=y
CONFIG_PCCARD_NONSTATIC=m
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_AOUT is not set
# CONFIG_BINFMT_MISC is not set
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_INET6_TUNNEL=m
CONFIG_IPV6_TUNNEL=m
# CONFIG_NETFILTER is not set
#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
CONFIG_ATM=m
# CONFIG_ATM_CLIP is not set
# CONFIG_ATM_LANE is not set
# CONFIG_ATM_BR2684 is not set
# CONFIG_BRIDGE is not set
CONFIG_VLAN_8021Q=m
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m
#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIDTL1=m
CONFIG_BT_HCIBT3C=m
CONFIG_BT_HCIBLUECARD=m
CONFIG_BT_HCIBTUART=m
CONFIG_BT_HCIVHCI=m
# CONFIG_IEEE80211 is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
CONFIG_DEBUG_DRIVER=y
#
# Connector - unified userspace <-> kernelspace linker
#
CONFIG_CONNECTOR=m
#
# Memory Technology Devices (MTD)
#
CONFIG_MTD=y
CONFIG_MTD_DEBUG=y
CONFIG_MTD_DEBUG_VERBOSE=3
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
#
# RAM/ROM/Flash chip drivers
#
# CONFIG_MTD_CFI is not set
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
# CONFIG_MTD_TS5500 is not set
# CONFIG_MTD_PLATRAM is not set
#
# Self-contained MTD device drivers
#
# CONFIG_MTD_PMC551 is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
CONFIG_MTD_MTDRAM=m
CONFIG_MTDRAM_TOTAL_SIZE=4096
CONFIG_MTDRAM_ERASE_SIZE=128
# CONFIG_MTD_BLKMTD is not set
# CONFIG_MTD_BLOCK2MTD is not set
#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
#
# NAND Flash Device Drivers
#
# CONFIG_MTD_NAND is not set
#
# OneNAND Flash Device Drivers
#
# CONFIG_MTD_ONENAND is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set
#
# Protocols
#
# CONFIG_ISAPNP is not set
# CONFIG_PNPBIOS is not set
CONFIG_PNPACPI=y
#
# Block devices
#
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_DEV_XD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_INITRD=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_CMD640=y
CONFIG_BLK_DEV_CMD640_ENHANCED=y
CONFIG_BLK_DEV_IDEPNP=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
CONFIG_BLK_DEV_OPTI621=y
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_CS5535 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
CONFIG_BLK_DEV_PDC202XX_OLD=y
# CONFIG_PDC202XX_BURST is not set
CONFIG_BLK_DEV_PDC202XX_NEW=y
CONFIG_PDC202XX_FORCE=y
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_IDE_CHIPSETS=y
#
# Note: most of these also require special kernel boot parameters
#
CONFIG_BLK_DEV_4DRIVES=y
# CONFIG_BLK_DEV_ALI14XX is not set
# CONFIG_BLK_DEV_DTC2278 is not set
# CONFIG_BLK_DEV_HT6560B is not set
# CONFIG_BLK_DEV_QD65XX is not set
# CONFIG_BLK_DEV_UMC8672 is not set
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_IVB=y
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=m
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=m
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=m
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=m
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA24XX is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# PCMCIA SCSI adapter support
#
# CONFIG_PCMCIA_AHA152X is not set
# CONFIG_PCMCIA_FDOMAIN is not set
# CONFIG_PCMCIA_NINJA_SCSI is not set
# CONFIG_PCMCIA_QLOGIC is not set
# CONFIG_PCMCIA_SYM53C500 is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=m
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set
CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
# CONFIG_IEEE1394_EXPORT_FULL_API is not set
#
# Device Drivers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=m
#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
CONFIG_IEEE1394_CMP=m
# CONFIG_IEEE1394_AMDTP is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_NET_SB1000 is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# PHY device support
#
# CONFIG_PHYLIB is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
# CONFIG_CS89x0 is not set
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
CONFIG_E100=m
# CONFIG_LNE390 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# PCMCIA network device support
#
# CONFIG_NET_PCMCIA is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# ATM drivers
#
# CONFIG_ATM_DUMMY is not set
# CONFIG_ATM_TCP is not set
# CONFIG_ATM_LANAI is not set
# CONFIG_ATM_ENI is not set
# CONFIG_ATM_FIRESTREAM is not set
# CONFIG_ATM_ZATM is not set
# CONFIG_ATM_NICSTAR is not set
# CONFIG_ATM_IDT77252 is not set
# CONFIG_ATM_AMBASSADOR is not set
# CONFIG_ATM_HORIZON is not set
# CONFIG_ATM_IA is not set
# CONFIG_ATM_FORE200E_MAYBE is not set
# CONFIG_ATM_HE is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
CONFIG_INPUT_EVBUG=y
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_SERIAL=m
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
# CONFIG_INPUT_WISTRON_BTNS is not set
# CONFIG_INPUT_UINPUT is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_CS=m
CONFIG_SERIAL_8250_ACPI=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
CONFIG_SERIAL_8250_RSA=y
# CONFIG_SERIAL_8250_FOURPORT is not set
# CONFIG_SERIAL_8250_ACCENT is not set
# CONFIG_SERIAL_8250_BOCA is not set
# CONFIG_SERIAL_8250_HUB6 is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
#
# IPMI
#
CONFIG_IPMI_HANDLER=m
# CONFIG_IPMI_PANIC_EVENT is not set
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_NVRAM is not set
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
CONFIG_AGP=m
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_ATI is not set
CONFIG_AGP_AMD=m
# CONFIG_AGP_AMD64 is not set
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
# CONFIG_DRM is not set
#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
# CONFIG_CARDMAN_4000 is not set
# CONFIG_CARDMAN_4040 is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m
#
# TPM devices
#
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ALGOPCA=m
#
# I2C Hardware Bus support
#
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI1563=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
CONFIG_I2C_I801=m
CONFIG_I2C_I810=m
CONFIG_I2C_PIIX4=m
CONFIG_I2C_ISA=m
CONFIG_I2C_NFORCE2=m
CONFIG_I2C_PARPORT_LIGHT=m
CONFIG_I2C_PROSAVAGE=m
CONFIG_I2C_SAVAGE4=m
CONFIG_SCx200_ACB=m
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
# CONFIG_I2C_STUB is not set
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
CONFIG_I2C_VOODOO3=m
CONFIG_I2C_PCA_ISA=m
#
# Miscellaneous I2C Chip support
#
CONFIG_SENSORS_DS1337=m
# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=m
CONFIG_SENSORS_PCF8574=m
# CONFIG_SENSORS_PCA9539 is not set
CONFIG_SENSORS_PCF8591=m
CONFIG_SENSORS_RTC8564=m
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_RTC_X1205_I2C is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
CONFIG_SENSORS_ADM1031=m
# CONFIG_SENSORS_ADM9240 is not set
CONFIG_SENSORS_ASB100=m
# CONFIG_SENSORS_ATXP1 is not set
CONFIG_SENSORS_DS1621=m
CONFIG_SENSORS_FSCHER=m
CONFIG_SENSORS_FSCPOS=m
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
CONFIG_SENSORS_MAX1619=m
CONFIG_SENSORS_PC87360=m
CONFIG_SENSORS_SIS5595=m
CONFIG_SENSORS_SMSC47M1=m
CONFIG_SENSORS_SMSC47B397=m
CONFIG_SENSORS_VIA686A=m
CONFIG_SENSORS_W83781D=m
# CONFIG_SENSORS_W83792D is not set
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_HDAPS is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Misc devices
#
# CONFIG_IBM_ASM is not set
#
# Multimedia Capabilities Port drivers
#
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
#
# Video For Linux
#
#
# Video Adapters
#
CONFIG_VIDEO_BT848=m
# CONFIG_VIDEO_SAA6588 is not set
CONFIG_VIDEO_PMS=m
CONFIG_VIDEO_CPIA=m
CONFIG_VIDEO_CPIA_USB=m
CONFIG_VIDEO_SAA5246A=m
CONFIG_VIDEO_SAA5249=m
CONFIG_TUNER_3036=m
CONFIG_VIDEO_STRADIS=m
CONFIG_VIDEO_ZORAN=m
CONFIG_VIDEO_ZORAN_BUZ=m
CONFIG_VIDEO_ZORAN_DC10=m
CONFIG_VIDEO_ZORAN_DC30=m
CONFIG_VIDEO_ZORAN_LML33=m
CONFIG_VIDEO_ZORAN_LML33R10=m
CONFIG_VIDEO_SAA7134=m
# CONFIG_VIDEO_SAA7134_ALSA is not set
CONFIG_VIDEO_MXB=m
CONFIG_VIDEO_DPC=m
CONFIG_VIDEO_HEXIUM_ORION=m
CONFIG_VIDEO_HEXIUM_GEMINI=m
CONFIG_VIDEO_CX88=m
# CONFIG_VIDEO_EM28XX is not set
CONFIG_VIDEO_OVCAMCHIP=m
# CONFIG_VIDEO_AUDIO_DECODER is not set
# CONFIG_VIDEO_DECODER is not set
#
# Radio Adapters
#
CONFIG_RADIO_CADET=m
CONFIG_RADIO_RTRACK=m
CONFIG_RADIO_RTRACK2=m
CONFIG_RADIO_AZTECH=m
CONFIG_RADIO_GEMTEK=m
CONFIG_RADIO_GEMTEK_PCI=m
CONFIG_RADIO_MAXIRADIO=m
CONFIG_RADIO_MAESTRO=m
CONFIG_RADIO_SF16FMI=m
CONFIG_RADIO_SF16FMR2=m
CONFIG_RADIO_TERRATEC=m
CONFIG_RADIO_TRUST=m
CONFIG_RADIO_TYPHOON=m
# CONFIG_RADIO_TYPHOON_PROC_FS is not set
CONFIG_RADIO_ZOLTRIX=m
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
CONFIG_VIDEO_SAA7146=m
CONFIG_VIDEO_SAA7146_VV=m
CONFIG_VIDEO_VIDEOBUF=m
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_IR=m
CONFIG_VIDEO_TVEEPROM=m
#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_MACMODES is not set
CONFIG_FB_MODE_HELPERS=y
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=m
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_I810 is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_CYBLA is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
#
CONFIG_SOUND=y
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_AC97_BUS=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
#
# ISA devices
#
# CONFIG_SND_AD1816A is not set
# CONFIG_SND_AD1848 is not set
# CONFIG_SND_CS4231 is not set
# CONFIG_SND_CS4232 is not set
# CONFIG_SND_CS4236 is not set
# CONFIG_SND_ES968 is not set
# CONFIG_SND_ES1688 is not set
# CONFIG_SND_ES18XX is not set
# CONFIG_SND_GUSCLASSIC is not set
# CONFIG_SND_GUSEXTREME is not set
# CONFIG_SND_GUSMAX is not set
# CONFIG_SND_INTERWAVE is not set
# CONFIG_SND_INTERWAVE_STB is not set
# CONFIG_SND_OPTI92X_AD1848 is not set
# CONFIG_SND_OPTI92X_CS4231 is not set
# CONFIG_SND_OPTI93X is not set
# CONFIG_SND_SB8 is not set
# CONFIG_SND_SB16 is not set
# CONFIG_SND_SBAWE is not set
# CONFIG_SND_WAVEFRONT is not set
# CONFIG_SND_ALS100 is not set
# CONFIG_SND_AZT2320 is not set
# CONFIG_SND_CMI8330 is not set
# CONFIG_SND_DT019X is not set
# CONFIG_SND_OPL3SA2 is not set
# CONFIG_SND_SGALAXY is not set
# CONFIG_SND_SSCAPE is not set
#
# PCI devices
#
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
CONFIG_SND_ICE1712=m
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_HDA_INTEL is not set
#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
#
# PCMCIA devices
#
# CONFIG_SND_VXPOCKET is not set
# CONFIG_SND_PDAUDIOCF is not set
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_SL811_HCD=m
CONFIG_USB_SL811_CS=m
#
# USB Device Class drivers
#
# CONFIG_OBSOLETE_OSS_USB_DRIVER is not set
CONFIG_USB_ACM=m
# CONFIG_USB_PRINTER is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
#
# USB Input Devices
#
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
CONFIG_HID_FF=y
CONFIG_HID_PID=y
CONFIG_LOGITECH_FF=y
CONFIG_THRUSTMASTER_FF=y
CONFIG_USB_HIDDEV=y
#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
CONFIG_USB_AIPTEK=m
CONFIG_USB_WACOM=m
# CONFIG_USB_ACECAD is not set
CONFIG_USB_KBTAB=m
# CONFIG_USB_POWERMATE is not set
CONFIG_USB_MTOUCH=m
# CONFIG_USB_ITMTOUCH is not set
CONFIG_USB_EGALAX=m
# CONFIG_USB_YEALINK is not set
CONFIG_USB_XPAD=m
CONFIG_USB_ATI_REMOTE=m
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set
#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m
#
# USB Multimedia devices
#
CONFIG_USB_DABUSB=m
CONFIG_USB_VICAM=m
CONFIG_USB_DSBR=m
CONFIG_USB_IBMCAM=m
CONFIG_USB_KONICAWC=m
CONFIG_USB_OV511=m
CONFIG_USB_SE401=m
CONFIG_USB_SN9C102=m
CONFIG_USB_STV680=m
CONFIG_USB_W9968CF=m
CONFIG_USB_PWC=m
#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
# CONFIG_USB_NET_GL620A is not set
# CONFIG_USB_NET_NET1080 is not set
# CONFIG_USB_NET_PLUSB is not set
# CONFIG_USB_NET_RNDIS_HOST is not set
# CONFIG_USB_NET_CDC_SUBSET is not set
# CONFIG_USB_NET_ZAURUS is not set
# CONFIG_USB_MON is not set
#
# USB port drivers
#
#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRPRIME=m
# CONFIG_USB_SERIAL_ANYDATA is not set
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
# CONFIG_USB_SERIAL_IR is not set
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_PL2303=m
# CONFIG_USB_SERIAL_HP4X is not set
# CONFIG_USB_SERIAL_SAFE is not set
CONFIG_USB_SERIAL_TI=m
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_AUERSWALD=m
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
CONFIG_USB_LCD=m
CONFIG_USB_LED=m
CONFIG_USB_CYTHERM=m
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
CONFIG_USB_IDMOUSE=m
CONFIG_USB_SISUSBVGA=m
# CONFIG_USB_SISUSBVGA_CON is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TEST is not set
#
# USB DSL modem support
#
CONFIG_USB_ATM=m
CONFIG_USB_SPEEDTOUCH=m
# CONFIG_USB_CXACRU is not set
# CONFIG_USB_XUSBATM is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
CONFIG_MMC=m
# CONFIG_MMC_DEBUG is not set
CONFIG_MMC_BLOCK=m
CONFIG_MMC_WBSD=m
#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set
#
# SN Devices
#
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
CONFIG_MINIX_FS=y
CONFIG_ROMFS_FS=y
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
CONFIG_BEFS_FS=m
# CONFIG_BEFS_DEBUG is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=2
CONFIG_JFFS2_FS_WRITEBUFFER=y
CONFIG_JFFS2_SUMMARY=y
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_RPCSEC_GSS_SPKM3=m
CONFIG_SMB_FS=m
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="cp437"
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
CONFIG_LDM_PARTITION=y
# CONFIG_LDM_DEBUG is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=y
#
# Instrumentation Support
#
# CONFIG_PROFILING is not set
# CONFIG_KPROBES is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_LOG_BUF_SHIFT=15
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
CONFIG_DEBUG_PREEMPT=y
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_FRAME_POINTER is not set
CONFIG_RCU_TORTURE_TEST=y
CONFIG_EARLY_PRINTK=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
#
# Security options
#
# CONFIG_KEYS is not set
CONFIG_SECURITY=y
# CONFIG_SECURITY_NETWORK is not set
CONFIG_SECURITY_CAPABILITIES=m
# CONFIG_SECURITY_ROOTPLUG is not set
# CONFIG_SECURITY_SECLVL is not set
# CONFIG_SECURITY_SELINUX is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_NULL is not set
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES_586=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
# CONFIG_CRYPTO_TEST is not set
#
# Hardware crypto devices
#
CONFIG_CRYPTO_DEV_PADLOCK=m
CONFIG_CRYPTO_DEV_PADLOCK_AES=y
#
# Library routines
#
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 MP
[IGD4-2P] System Controller (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at fc000000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at e000 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 MP
[IGD4-2P] AGP Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
0000:00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-768 [Opus]
ISA (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-768
[Opus] IDE (rev 04) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at f000 [size=16]
0000:00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI (rev 03)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:07.5 Multimedia audio controller: Advanced Micro Devices [AMD]
AMD-768 [Opus] Audio (rev 03)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin B routed to IRQ 7
Region 0: I/O ports at d000 [size=256]
Region 1: I/O ports at d400 [size=64]
0000:00:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-768 [Opus]
PCI (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000cfff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 50000000-500fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:01:05.0 VGA compatible controller: nVidia Corporation NV11
[GeForce2 MX/MX 400] (rev b2) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc.: Unknown device 403d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 7
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at f9000000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit-
FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
0000:02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-768
[Opus] USB (rev 07) (prog-if 10 [OHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin D routed to IRQ 11
Region 0: Memory at fb029000 (32-bit, non-prefetchable) [size=4K]
0000:02:04.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: AFAVLAB Technology Inc: Unknown device 0035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (250ns min, 10500ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fb02b000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:04.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: AFAVLAB Technology Inc: Unknown device 0035
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (250ns min, 10500ns max), cache line size 08
Interrupt: pin B routed to IRQ 7
Region 0: Memory at fb02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:04.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if
20 [EHCI])
Subsystem: AFAVLAB Technology Inc: Unknown device 00e0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8500ns max), cache line size 08
Interrupt: pin C routed to IRQ 11
Region 0: Memory at fb02d000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:05.0 Multimedia audio controller: VIA Technologies Inc.
ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02)
Subsystem: VIA Technologies Inc. M-Audio Delta Audiophile
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=32]
Region 1: I/O ports at a400 [size=16]
Region 2: I/O ports at a800 [size=16]
Region 3: I/O ports at ac00 [size=64]
Capabilities: [80] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23
IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Adaptec: Unknown device 0030
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fb028000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fb020000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02:07.0 Ethernet controller: Intel Corporation 82557/8/9
[Ethernet Pro 100] (rev 0d)
Subsystem: Intel Corporation EtherExpress PRO/100 Server Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fb02a000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b000 [size=64]
Region 2: Memory at fb000000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at 50000000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:02:08.0 RAID bus controller: Promise Technology, Inc. PDC20276
(MBFastTrak133 Lite) (rev 01) (prog-if 85)
Subsystem: Giga-byte Technology MBUltra 133
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at b400 [size=8]
Region 1: I/O ports at b800 [size=4]
Region 2: I/O ports at bc00 [size=8]
Region 3: I/O ports at c000 [size=4]
Region 4: I/O ports at c400 [size=16]
Region 5: Memory at fb024000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-11 0:01 ` Jan Rekorajski
@ 2006-01-11 0:19 ` Pete Zaitcev
2006-01-11 15:26 ` Alan Stern
1 sibling, 0 replies; 32+ messages in thread
From: Pete Zaitcev @ 2006-01-11 0:19 UTC (permalink / raw)
To: Jan Rekorajski
Cc: linux-kernel, dtor_core, vojtech, stern, mailing-lists-mmv,
jengelh, linux-usb-devel, gregkh, nouser, zaitcev
On Wed, 11 Jan 2006 01:01:51 +0100, Jan Rekorajski <baggins@sith.mimuw.edu.pl> wrote:
> This happens on Dell Precision 380, [...]
Continue no further. What is the BIOS's A-version? Anything below A04
is unusable.
-- Pete
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-10 15:37 ` Dmitry Torokhov
@ 2006-01-11 0:01 ` Jan Rekorajski
2006-01-11 0:19 ` Pete Zaitcev
2006-01-11 15:26 ` Alan Stern
[not found] ` <161717d50601101019k34a901a8x37fb28187a609490@mail.gmail.com>
1 sibling, 2 replies; 32+ messages in thread
From: Jan Rekorajski @ 2006-01-11 0:01 UTC (permalink / raw)
To: linux-kernel
Cc: Vojtech Pavlik, Alan Stern, Martin Bretschneider,
dtor_core @ ameritech. net Jan Engelhardt, linux-usb-devel,
Greg KH, Leonid
On Tue, 10 Jan 2006, Dmitry Torokhov wrote:
> We'll just have to wait for another report. "Sluggish typing" report
> looks promising.
With 2.6.14.6:
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
and my keyboard works.
with 2.6.15:
i8042.c: Can't read CTR while initializing i8042.
and no PS/2 keyboard.
This happens on Dell Precision 380, x86_64 kernel with SMP/HT, no options
on kernel command line, same kernel .config (modulo make oldconfig).
I tried all solutions I found on google, none works (beside connecting
USB keyboard or disabling USB in BIOS).
Jan
--
Jan Rękorajski | ALL SUSPECTS ARE GUILTY. PERIOD!
baggins<at>mimuw.edu.pl | OTHERWISE THEY WOULDN'T BE SUSPECTS, WOULD THEY?
BOFH, MANIAC | -- TROOPS by Kevin Rubio
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-10 15:28 ` Vojtech Pavlik
@ 2006-01-10 15:37 ` Dmitry Torokhov
2006-01-11 0:01 ` Jan Rekorajski
[not found] ` <161717d50601101019k34a901a8x37fb28187a609490@mail.gmail.com>
0 siblings, 2 replies; 32+ messages in thread
From: Dmitry Torokhov @ 2006-01-10 15:37 UTC (permalink / raw)
To: Vojtech Pavlik
Cc: Alan Stern, Martin Bretschneider, linux-kernel, Jan Engelhardt,
linux-usb-devel, Greg KH, Leonid
On 1/10/06, Vojtech Pavlik <vojtech@suse.cz> wrote:
> On Tue, Jan 10, 2006 at 10:12:21AM -0500, Alan Stern wrote:
> > On Tue, 10 Jan 2006, Vojtech Pavlik wrote:
> >
> > > It's usually that the BIOS does an incomplete emulation of the i8042
> > > chip, while still getting in the way to the real i8042. Usually GRUB and
> > > DOS don't care about sending any commands to the i8042, and so they
> > > work. The Linux i8042.c driver needs to use them to enable the PS/2
> > > mouse port and do other probing, and if the commans are not working, it
> > > just bails out.
> > >
> > > The question of course is why the handoff code doesn't work on that
> > > platform.
> >
> > It turned out that a BIOS upgrade fixed the problem, but this doesn't
> > answer your question.
> >
> > The problem wasn't an incomplete emulation of the i8042, because when the
> > USB handoff code was commented out the PS/2 keyboard worked okay. This
> > means the handoff, when enabled, wasn't being done correctly. That could
> > be the fault of the USB drivers or the BIOS (or both). We have no way to
> > tell which, because the users have all switched to the newer BIOS.
>
> As usual with BIOS interaction problems.
>
We'll just have to wait for another report. "Sluggish typing" report
looks promising.
--
Dmitry
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-10 15:12 ` Alan Stern
@ 2006-01-10 15:28 ` Vojtech Pavlik
2006-01-10 15:37 ` Dmitry Torokhov
0 siblings, 1 reply; 32+ messages in thread
From: Vojtech Pavlik @ 2006-01-10 15:28 UTC (permalink / raw)
To: Alan Stern
Cc: dtor_core, Martin Bretschneider, linux-kernel, Jan Engelhardt,
linux-usb-devel, Greg KH, Leonid
On Tue, Jan 10, 2006 at 10:12:21AM -0500, Alan Stern wrote:
> On Tue, 10 Jan 2006, Vojtech Pavlik wrote:
>
> > It's usually that the BIOS does an incomplete emulation of the i8042
> > chip, while still getting in the way to the real i8042. Usually GRUB and
> > DOS don't care about sending any commands to the i8042, and so they
> > work. The Linux i8042.c driver needs to use them to enable the PS/2
> > mouse port and do other probing, and if the commans are not working, it
> > just bails out.
> >
> > The question of course is why the handoff code doesn't work on that
> > platform.
>
> It turned out that a BIOS upgrade fixed the problem, but this doesn't
> answer your question.
>
> The problem wasn't an incomplete emulation of the i8042, because when the
> USB handoff code was commented out the PS/2 keyboard worked okay. This
> means the handoff, when enabled, wasn't being done correctly. That could
> be the fault of the USB drivers or the BIOS (or both). We have no way to
> tell which, because the users have all switched to the newer BIOS.
As usual with BIOS interaction problems.
--
Vojtech Pavlik
SuSE Labs, SuSE CR
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-10 7:43 ` Vojtech Pavlik
@ 2006-01-10 15:12 ` Alan Stern
2006-01-10 15:28 ` Vojtech Pavlik
0 siblings, 1 reply; 32+ messages in thread
From: Alan Stern @ 2006-01-10 15:12 UTC (permalink / raw)
To: Vojtech Pavlik
Cc: dtor_core, Martin Bretschneider, linux-kernel, Jan Engelhardt,
linux-usb-devel, Greg KH, Leonid
On Tue, 10 Jan 2006, Vojtech Pavlik wrote:
> It's usually that the BIOS does an incomplete emulation of the i8042
> chip, while still getting in the way to the real i8042. Usually GRUB and
> DOS don't care about sending any commands to the i8042, and so they
> work. The Linux i8042.c driver needs to use them to enable the PS/2
> mouse port and do other probing, and if the commans are not working, it
> just bails out.
>
> The question of course is why the handoff code doesn't work on that
> platform.
It turned out that a BIOS upgrade fixed the problem, but this doesn't
answer your question.
The problem wasn't an incomplete emulation of the i8042, because when the
USB handoff code was commented out the PS/2 keyboard worked okay. This
means the handoff, when enabled, wasn't being done correctly. That could
be the fault of the USB drivers or the BIOS (or both). We have no way to
tell which, because the users have all switched to the newer BIOS.
Alan Stern
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-09 17:23 ` Alan Stern
2006-01-09 17:54 ` Dmitry Torokhov
@ 2006-01-10 7:43 ` Vojtech Pavlik
2006-01-10 15:12 ` Alan Stern
1 sibling, 1 reply; 32+ messages in thread
From: Vojtech Pavlik @ 2006-01-10 7:43 UTC (permalink / raw)
To: Alan Stern
Cc: dtor_core, Martin Bretschneider, linux-kernel, Jan Engelhardt,
linux-usb-devel, Greg KH, Leonid
On Mon, Jan 09, 2006 at 12:23:04PM -0500, Alan Stern wrote:
> On Mon, 9 Jan 2006, Dmitry Torokhov wrote:
>
> > > It would be nice to know which part of the usb-handoff code causes the
> > > problem.
> >
> > Well, it's not handoff code causing problems per se, it's just that it
> > does not look like it performs handoff. If it did then disabling USB
> > legacy emulation in BIOS would have no effect, right?
>
> On the other hand, if the BIOS worked correctly then the ps/2 port would
> have no problems regardless of whether USB legacy emulation was on or off.
> Given that the keyboard works during bootup, I see only two possibilities:
>
> The USB handoff code somehow causes the BIOS to mess up the
> state of the 8042;
>
> The 8042 driver interacts badly with the firmware when USB
> legacy emulation is on, and the USB handoff code doesn't
> successfully turn off legacy emulation.
It's usually that the BIOS does an incomplete emulation of the i8042
chip, while still getting in the way to the real i8042. Usually GRUB and
DOS don't care about sending any commands to the i8042, and so they
work. The Linux i8042.c driver needs to use them to enable the PS/2
mouse port and do other probing, and if the commans are not working, it
just bails out.
The question of course is why the handoff code doesn't work on that
platform.
--
Vojtech Pavlik
SuSE Labs, SuSE CR
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-09 17:54 ` Dmitry Torokhov
@ 2006-01-09 20:08 ` Martin Bretschneider
2006-02-04 7:01 ` mahesh
1 sibling, 0 replies; 32+ messages in thread
From: Martin Bretschneider @ 2006-01-09 20:08 UTC (permalink / raw)
To: dtor_core
Cc: dmitry.torokhov, Alan Stern, linux-kernel, Jan Engelhardt,
linux-usb-devel, Greg KH, Leonid
Dmitry Torokhov <dmitry.torokhov@gmail.com> wrote:
Hi Dmitry,
> My experience is that USB legacy emulation in BIOS + ACPI works as
> long as you do not touch it and gets terribly confused if someone
> tries to actually use i8042 (like enable active multiplexing mode
> with 4 AUX ports). As soon as BIOS takes its dirty hands off i8042
> everything works fine.
>
> The problem it seems that when usb-handoff code was moved from pci
> quirks and enabled inconditionally something happened so it stopped
> doing handoff.
This words made me think about upgrading the BIOS. My former version
that caused the problem and made me start this thread was F6 from july
2005 and the most recent version is from december 2005[1]. Using this
BIOS the former problem is gone! Jens who has go the same motherboard
had the same idea and can confirm this "success" with the newer
BIOS. That is to say that I can use the keyboard (and mouse) using the
ps/2 ports with kernel 2.6.15 and enabled "USB keyboard support" in
the BIOS. The keyboard and mouse do also work -- as expected --
conncected to the USB.
Thus, I do not know what you kernel developers should do now. You can
say to the guys who have the ps/2 problem that they should update
their BIOS. But what should they do if their motherboard supplier
has not fixed the problem or does not provide BIOS updates at all?
And what exactly was the problem?
Honestly, I do not want to reflash the BIOS of my motherboard to the
older version for later debugging of modified kernel source code
since a power blackout during flashing the BIOS could destroy my
motherboard...
Kind regards from Martin
[1]
http://tw.giga-byte.com/Motherboard/Support/BIOS/BIOS_GA-K8NF-9.htm
--
http://www.bretschneidernet.de OpenPGP-key: 0x4EA52583
(*_ Ernest Hemingway:
$ cd /pub/ //\ I like to listen. I have learned a great deal
$ more beer V_/_ from listening carefully. Most people never listen.
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-09 18:36 ` Martin Bretschneider
@ 2006-01-09 19:09 ` Alan Stern
0 siblings, 0 replies; 32+ messages in thread
From: Alan Stern @ 2006-01-09 19:09 UTC (permalink / raw)
To: Martin Bretschneider
Cc: Dmitry Torokhov, linux-kernel, Jan Engelhardt, linux-usb-devel,
Greg KH, Leonid
On Mon, 9 Jan 2006, Martin Bretschneider wrote:
> Yes, I also use the OHCI controller (I guessed that this is
> necessary for low speed USB devices...), I commented the calls of
> quirk_usb_disable_?hci and renamed the compiled modules so that they
> cannot be loaded. Thus, the PS/2 keyboard *does* work with "USB
> keyboard support" enabled in the BIOS with kernel 2.6.15. But - of
> cource - no USB device does work.
Good work! This proves that the i8042 driver _is_ compatible with BIOS
legacy support.
The next step is to find out which part of the USB handoff code isn't
working right. Martin, first try uncommenting just the
quirk_usb_disable_ohci call but leave the modules renamed. That will
indicate whether the problem is in the handoff code or in the driver.
Next, try renaming the ohci-hcd.ko file back to its correct name so it
does get loaded. If the keyboard continues to work then the problem must
lie in either UHCI or EHCI. Try doing the same two-part test (enable the
quirk code and then un-rename the file) with each of them to see exactly
at what point the keyboard stops working.
Alan Stern
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-09 15:32 ` Alan Stern
2006-01-09 16:50 ` Dmitry Torokhov
@ 2006-01-09 18:36 ` Martin Bretschneider
2006-01-09 19:09 ` Alan Stern
1 sibling, 1 reply; 32+ messages in thread
From: Martin Bretschneider @ 2006-01-09 18:36 UTC (permalink / raw)
To: Alan Stern
Cc: Dmitry Torokhov, linux-kernel, Jan Engelhardt, linux-usb-devel,
Greg KH, Leonid
Alan Stern <stern@rowland.harvard.edu> wrote:
Hi Alan,
> On Mon, 9 Jan 2006, Dmitry Torokhov wrote:
>
> > On Sunday 08 January 2006 16:23, Martin Bretschneider wrote:
> > > Hello,
> > >
> > > Jens Nödler who has got the same motheboard (Gigabyte GA-K8NF-9
> > > with nforce4 chipset) can confirm my problem. But he found out
> > > that the keyboard connected to the ps/2 port does work with
> > > kernel 2.6.15 if "USB keyboard support" is disabled in the BIOS.
> > >
> >
> > Ok, I an getting enough reports to conclude that the new
> > usb-handoff code does not seem to be working. Let's try CCing USB
> > list and other parties involved :)
> >
> > Greg, Alan, any ideas?
>
> It would be nice to know which part of the usb-handoff code causes
> the problem. In the 2.6.15 source file
> drivers/usb/host/pci-quirks.c, at the end of the file is this
> routine:
>
> static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
> {
> if (pdev->class == PCI_CLASS_SERIAL_USB_UHCI)
> quirk_usb_handoff_uhci(pdev);
> else if (pdev->class == PCI_CLASS_SERIAL_USB_OHCI)
> quirk_usb_handoff_ohci(pdev);
> else if (pdev->class == PCI_CLASS_SERIAL_USB_EHCI)
> quirk_usb_disable_ehci(pdev);
> }
>
> If you comment out the call to quirk_usb_handoff_uhci and rename
> the /lib/modules/2.6.15/kernel/drivers/usb/host/uhci-hcd.ko file so
> that it doesn't get loaded automatically, does that fix things?
>
> Similarly, if you comment out the call to quirk_usb_disable_ehci
> and rename /lib/modules/.../ehci-hcd.ko so that it doesn't get
> loaded, does that help?
>
> Leonid's system log showed that he doesn't have an OHCI controller,
> but if Martin does then he should do the same test with
> quirk_usb_handoff_ohci.
Yes, I also use the OHCI controller (I guessed that this is
necessary for low speed USB devices...), I commented the calls of
quirk_usb_disable_?hci and renamed the compiled modules so that they
cannot be loaded. Thus, the PS/2 keyboard *does* work with "USB
keyboard support" enabled in the BIOS with kernel 2.6.15. But - of
cource - no USB device does work.
Kind regards, Martin
--
http://www.bretschneidernet.de OpenPGP-key: 0x4EA52583
(o_ Ernest Hemingway:
(o_ (o_ (o_ //\ I like to listen. I have learned a great deal
(\)_(\)_(\)_V_/_ from listening carefully. Most people never listen.
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-09 17:23 ` Alan Stern
@ 2006-01-09 17:54 ` Dmitry Torokhov
2006-01-09 20:08 ` Martin Bretschneider
2006-02-04 7:01 ` mahesh
2006-01-10 7:43 ` Vojtech Pavlik
1 sibling, 2 replies; 32+ messages in thread
From: Dmitry Torokhov @ 2006-01-09 17:54 UTC (permalink / raw)
To: Alan Stern
Cc: Martin Bretschneider, linux-kernel, Jan Engelhardt,
linux-usb-devel, Greg KH, Leonid
On 1/9/06, Alan Stern <stern@rowland.harvard.edu> wrote:
> On Mon, 9 Jan 2006, Dmitry Torokhov wrote:
>
> > > It would be nice to know which part of the usb-handoff code causes the
> > > problem.
> >
> > Well, it's not handoff code causing problems per se, it's just that it
> > does not look like it performs handoff. If it did then disabling USB
> > legacy emulation in BIOS would have no effect, right?
>
> On the other hand, if the BIOS worked correctly then the ps/2 port would
> have no problems regardless of whether USB legacy emulation was on or off.
> Given that the keyboard works during bootup, I see only two possibilities:
>
> The USB handoff code somehow causes the BIOS to mess up the
> state of the 8042;
>
> The 8042 driver interacts badly with the firmware when USB
> legacy emulation is on, and the USB handoff code doesn't
> successfully turn off legacy emulation.
>
> My earlier suggestion was an attempt to test the first possibility. The
> second is harder to test because it implies problems in both the 8042
> driver and the USB handoff code.
>
My experience is that USB legacy emulation in BIOS + ACPI works as
long as you do not touch it and gets terribly confused if someone
tries to actually use i8042 (like enable active multiplexing mode with
4 AUX ports). As soon as BIOS takes its dirty hands off i8042
everything works fine.
The problem it seems that when usb-handoff code was moved from pci
quirks and enabled inconditionally something happened so it stopped
doing handoff.
--
Dmitry
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-09 16:50 ` Dmitry Torokhov
@ 2006-01-09 17:23 ` Alan Stern
2006-01-09 17:54 ` Dmitry Torokhov
2006-01-10 7:43 ` Vojtech Pavlik
0 siblings, 2 replies; 32+ messages in thread
From: Alan Stern @ 2006-01-09 17:23 UTC (permalink / raw)
To: dtor_core
Cc: Martin Bretschneider, linux-kernel, Jan Engelhardt,
linux-usb-devel, Greg KH, Leonid
On Mon, 9 Jan 2006, Dmitry Torokhov wrote:
> > It would be nice to know which part of the usb-handoff code causes the
> > problem.
>
> Well, it's not handoff code causing problems per se, it's just that it
> does not look like it performs handoff. If it did then disabling USB
> legacy emulation in BIOS would have no effect, right?
On the other hand, if the BIOS worked correctly then the ps/2 port would
have no problems regardless of whether USB legacy emulation was on or off.
Given that the keyboard works during bootup, I see only two possibilities:
The USB handoff code somehow causes the BIOS to mess up the
state of the 8042;
The 8042 driver interacts badly with the firmware when USB
legacy emulation is on, and the USB handoff code doesn't
successfully turn off legacy emulation.
My earlier suggestion was an attempt to test the first possibility. The
second is harder to test because it implies problems in both the 8042
driver and the USB handoff code.
Alan Stern
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-09 15:32 ` Alan Stern
@ 2006-01-09 16:50 ` Dmitry Torokhov
2006-01-09 17:23 ` Alan Stern
2006-01-09 18:36 ` Martin Bretschneider
1 sibling, 1 reply; 32+ messages in thread
From: Dmitry Torokhov @ 2006-01-09 16:50 UTC (permalink / raw)
To: Alan Stern
Cc: Martin Bretschneider, linux-kernel, Jan Engelhardt,
linux-usb-devel, Greg KH, Leonid
On 1/9/06, Alan Stern <stern@rowland.harvard.edu> wrote:
> On Mon, 9 Jan 2006, Dmitry Torokhov wrote:
>
> > On Sunday 08 January 2006 16:23, Martin Bretschneider wrote:
> > > Hello,
> > >
> > > Jens Nödler who has got the same motheboard (Gigabyte GA-K8NF-9 with
> > > nforce4 chipset) can confirm my problem. But he found out that the
> > > keyboard connected to the ps/2 port does work with kernel 2.6.15 if
> > > "USB keyboard support" is disabled in the BIOS.
> > >
> >
> > Ok, I an getting enough reports to conclude that the new usb-handoff
> > code does not seem to be working. Let's try CCing USB list and other
> > parties involved :)
> >
> > Greg, Alan, any ideas?
>
> It would be nice to know which part of the usb-handoff code causes the
> problem.
Well, it's not handoff code causing problems per se, it's just that it
does not look like it performs handoff. If it did then disabling USB
legacy emulation in BIOS would have no effect, right?
--
Dmitry
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-09 6:26 ` Dmitry Torokhov
@ 2006-01-09 15:32 ` Alan Stern
2006-01-09 16:50 ` Dmitry Torokhov
2006-01-09 18:36 ` Martin Bretschneider
0 siblings, 2 replies; 32+ messages in thread
From: Alan Stern @ 2006-01-09 15:32 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: Martin Bretschneider, linux-kernel, Jan Engelhardt,
linux-usb-devel, Greg KH, Leonid
On Mon, 9 Jan 2006, Dmitry Torokhov wrote:
> On Sunday 08 January 2006 16:23, Martin Bretschneider wrote:
> > Hello,
> >
> > Jens Nödler who has got the same motheboard (Gigabyte GA-K8NF-9 with
> > nforce4 chipset) can confirm my problem. But he found out that the
> > keyboard connected to the ps/2 port does work with kernel 2.6.15 if
> > "USB keyboard support" is disabled in the BIOS.
> >
>
> Ok, I an getting enough reports to conclude that the new usb-handoff
> code does not seem to be working. Let's try CCing USB list and other
> parties involved :)
>
> Greg, Alan, any ideas?
It would be nice to know which part of the usb-handoff code causes the
problem. In the 2.6.15 source file drivers/usb/host/pci-quirks.c, at the
end of the file is this routine:
static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
{
if (pdev->class == PCI_CLASS_SERIAL_USB_UHCI)
quirk_usb_handoff_uhci(pdev);
else if (pdev->class == PCI_CLASS_SERIAL_USB_OHCI)
quirk_usb_handoff_ohci(pdev);
else if (pdev->class == PCI_CLASS_SERIAL_USB_EHCI)
quirk_usb_disable_ehci(pdev);
}
If you comment out the call to quirk_usb_handoff_uhci and rename the
/lib/modules/2.6.15/kernel/drivers/usb/host/uhci-hcd.ko file so that it
doesn't get loaded automatically, does that fix things?
Similarly, if you comment out the call to quirk_usb_disable_ehci and
rename /lib/modules/.../ehci-hcd.ko so that it doesn't get loaded, does
that help?
Leonid's system log showed that he doesn't have an OHCI controller, but if
Martin does then he should do the same test with quirk_usb_handoff_ohci.
Alan Stern
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-08 22:19 ` Dmitry Torokhov
@ 2006-01-09 9:50 ` Martin Bretschneider
0 siblings, 0 replies; 32+ messages in thread
From: Martin Bretschneider @ 2006-01-09 9:50 UTC (permalink / raw)
To: Dmitry Torokhov, linux-kernel
Dmitry Torokhov <dtor_core@ameritech.net> wrote:
Hi Dmitry,
> On Sunday 08 January 2006 16:23, Martin Bretschneider wrote:
> > Hello,
> >
> > Jens Nödler who has got the same motheboard (Gigabyte GA-K8NF-9
> > with nforce4 chipset) can confirm my problem. But he found out
> > that the keyboard connected to the ps/2 port does work with
> > kernel 2.6.15 if "USB keyboard support" is disabled in the BIOS.
> >
>
> And what about your box? Does it also help you?
Yes, it does:)
Martin
--
http://www.bretschneidernet.de OpenPGP-key: 0x4EA52583
(o__o) Philip R. Zimmermann:
//\/\\ If privacy is outlawed,
V_/\_V only outlaws will have privacy.
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-08 21:23 ` Martin Bretschneider
2006-01-08 22:19 ` Dmitry Torokhov
@ 2006-01-09 6:26 ` Dmitry Torokhov
2006-01-09 15:32 ` Alan Stern
1 sibling, 1 reply; 32+ messages in thread
From: Dmitry Torokhov @ 2006-01-09 6:26 UTC (permalink / raw)
To: Martin Bretschneider
Cc: linux-kernel, Jan Engelhardt, linux-usb-devel, Greg KH,
Alan Stern, Leonid
On Sunday 08 January 2006 16:23, Martin Bretschneider wrote:
> Hello,
>
> Jens Nödler who has got the same motheboard (Gigabyte GA-K8NF-9 with
> nforce4 chipset) can confirm my problem. But he found out that the
> keyboard connected to the ps/2 port does work with kernel 2.6.15 if
> "USB keyboard support" is disabled in the BIOS.
>
Ok, I an getting enough reports to conclude that the new usb-handoff
code does not seem to be working. Let's try CCing USB list and other
parties involved :)
Greg, Alan, any ideas?
--
Dmitry
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
@ 2006-01-09 6:10 Leonid
0 siblings, 0 replies; 32+ messages in thread
From: Leonid @ 2006-01-09 6:10 UTC (permalink / raw)
To: linux-kernel
Dimitry,
I have the same problem. I have Dell Dimension 380 box,
PS/2 mouse and keyboard.
Kernel worked under 2.6.13.1 and 2.6.14
Then I upgraded to 2.6.15:
cp linux-2.6.14/.config linux-2.6.15/.config
cd linux-2.6.15
make oldconfig
... and usual kernel compilation ...
Result: system is successfully booted, no error messages, loads X window,
... but both keyboard and mouse are dead: they do not respond.
It was not the first time I have this famous problem. Last time it
was different keyboard, different motherboard, different kernel. That time
your advice to use kernel parameter "i8042.noacpi=1" helped. This time this
does not help. My BIOS setup has an only two choices: to enable USB controller
or to disable it. When I disable USB controller, then after booting keyboard
and mouse are working, but no USB devices work.
Configuration files:
http://lacerta.miz.nao.ac.jp/misc/config_2_6_14.txt (2.6.14 which works)
http://lacerta.miz.nao.ac.jp/misc/config_2_6_15.txt (2.6.15 which does not work)
Kernel messages:
http://lacerta.miz.nao.ac.jp/misc/kernel_2_6_14.txt (2.6.14 which works)
http://lacerta.miz.nao.ac.jp/misc/kernel_2_6_15.txt (2.6.15 which does not work)
http://lacerta.miz.nao.ac.jp/misc/kernel_2_6_15_nousb.txt (2.6.15 with
disabled USB controller, which works, but no USB devices are visible)
(2.6.15, kernel option i8042.noacpi=1 -- does not help)
http://lacerta.miz.nao.ac.jp/misc/kernel_2_6_15_i8042_noacpi.txt
(2.6.15, kernel option acpi=off -- does not help)
http://lacerta.miz.nao.ac.jp/misc/kernel_2_6_15_acpi_off.txt
(2.6.15, kernel option usb-handoff -- does not help)
http://lacerta.miz.nao.ac.jp/misc/kernel_2_6_15_usb-handoff.txt
(2.6.15, kernel option i8042.debug=1 )
http://lacerta.miz.nao.ac.jp/misc/kernel_2_6_15_i8042_debug.txt
http://lacerta.miz.nao.ac.jp/misc/messages_2_6_15_i8042_debug.txt
Results of
cat /proc/acpi/dst > proc_acpi_dst.txt
http://lacerta.miz.nao.ac.jp/misc/proc_acpi_dst.txt
Leonid
09-JAN-2006 15:07:07
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-08 21:23 ` Martin Bretschneider
@ 2006-01-08 22:19 ` Dmitry Torokhov
2006-01-09 9:50 ` Martin Bretschneider
2006-01-09 6:26 ` Dmitry Torokhov
1 sibling, 1 reply; 32+ messages in thread
From: Dmitry Torokhov @ 2006-01-08 22:19 UTC (permalink / raw)
To: Martin Bretschneider; +Cc: linux-kernel, Dmitry Torokhov, Jan Engelhardt
On Sunday 08 January 2006 16:23, Martin Bretschneider wrote:
> Hello,
>
> Jens Nödler who has got the same motheboard (Gigabyte GA-K8NF-9 with
> nforce4 chipset) can confirm my problem. But he found out that the
> keyboard connected to the ps/2 port does work with kernel 2.6.15 if
> "USB keyboard support" is disabled in the BIOS.
>
And what about your box? Does it also help you?
--
Dmitry
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-05 13:58 Martin Bretschneider
` (2 preceding siblings ...)
2006-01-06 16:29 ` Martin Bretschneider
@ 2006-01-08 21:23 ` Martin Bretschneider
2006-01-08 22:19 ` Dmitry Torokhov
2006-01-09 6:26 ` Dmitry Torokhov
3 siblings, 2 replies; 32+ messages in thread
From: Martin Bretschneider @ 2006-01-08 21:23 UTC (permalink / raw)
To: linux-kernel, Dmitry Torokhov, Jan Engelhardt
Hello,
Jens Nödler who has got the same motheboard (Gigabyte GA-K8NF-9 with
nforce4 chipset) can confirm my problem. But he found out that the
keyboard connected to the ps/2 port does work with kernel 2.6.15 if
"USB keyboard support" is disabled in the BIOS.
Martin
--
http://www.bretschneidernet.de OpenPGP-key: 0x4EA52583
(*_ Jean-Luc Picard (Star Trek TNG):
$ cd /pub/ //\ Sometimes it's possible to make no mistakes
$ more beer V_/_ and still lose. It is not a weakness. It is life.
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-06 16:29 ` Martin Bretschneider
@ 2006-01-06 19:00 ` Jesper Juhl
0 siblings, 0 replies; 32+ messages in thread
From: Jesper Juhl @ 2006-01-06 19:00 UTC (permalink / raw)
To: Martin Bretschneider; +Cc: linux-kernel, Jan Engelhardt, Dmitry Torokhov
On 1/6/06, Martin Bretschneider <mailing-lists-mmv@bretschneidernet.de> wrote:
> Martin Bretschneider <mailing-lists-mmv@bretschneidernet.de> wrote:
>
> with some debugging help of Dmitry Torokhov and Jan Engelhardt I
> could *not* find the cause why the PS/2 keyboard does not work.
>
> But other things do work:
> - If I connect the keyboard with the USB, it does work with 2.6.15.
> - If I use another pc with an old AMD 500, the PS/2 keyboard does
> work.
>
> So, it could be a strange problem between the motherboard chipset
> (nforce4), the 2.6.15 kernel and the PS/2 connection.
>
> I am going to test some Kernels beetween 2.6.14.2 and 2.6.15 to find
> the problem in some time.
>
Once you've narrowed down what two release kernels are "last one
working" & "first one broken" you can get even closer by doing a git
bisection search between those two to (hopefully) narrow it down to
the exact git commit that broke it.
It's a bit of work, but usually very useful to track down the exact
thing that broke it if nothing else finds the problem :)
--
Jesper Juhl <jesper.juhl@gmail.com>
Don't top-post http://www.catb.org/~esr/jargon/html/T/top-post.html
Plain text mails only, please http://www.expita.com/nomime.html
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-05 13:58 Martin Bretschneider
2006-01-05 14:37 ` Dmitry Torokhov
2006-01-06 7:21 ` Jan Engelhardt
@ 2006-01-06 16:29 ` Martin Bretschneider
2006-01-06 19:00 ` Jesper Juhl
2006-01-08 21:23 ` Martin Bretschneider
3 siblings, 1 reply; 32+ messages in thread
From: Martin Bretschneider @ 2006-01-06 16:29 UTC (permalink / raw)
To: linux-kernel, Jan Engelhardt, Dmitry Torokhov
Martin Bretschneider <mailing-lists-mmv@bretschneidernet.de> wrote:
with some debugging help of Dmitry Torokhov and Jan Engelhardt I
could *not* find the cause why the PS/2 keyboard does not work.
But other things do work:
- If I connect the keyboard with the USB, it does work with 2.6.15.
- If I use another pc with an old AMD 500, the PS/2 keyboard does
work.
So, it could be a strange problem between the motherboard chipset
(nforce4), the 2.6.15 kernel and the PS/2 connection.
I am going to test some Kernels beetween 2.6.14.2 and 2.6.15 to find
the problem in some time.
Martin
--
http://www.bretschneidernet.de OpenPGP-key: 0x4EA52583
_o)(o_ Sallust:
-./\\//\.- Nam idem velle atque idem
_\_VV_/_ nolle, ea demum firma amicitia est.
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-05 13:58 Martin Bretschneider
2006-01-05 14:37 ` Dmitry Torokhov
@ 2006-01-06 7:21 ` Jan Engelhardt
2006-01-06 16:29 ` Martin Bretschneider
2006-01-08 21:23 ` Martin Bretschneider
3 siblings, 0 replies; 32+ messages in thread
From: Jan Engelhardt @ 2006-01-06 7:21 UTC (permalink / raw)
To: Martin Bretschneider; +Cc: linux-kernel
>I cannot tell if the PS/2 mouse does not work either since I cannot
>start X.
If you have another box, you could ssh in and start X. Or you could start
"showkey", to see if it's a problem (e.g. empty keymap) that kbd introduces
during boot.
Therefore, does keyboard work when you boot with the "-b" option?
Jan Engelhardt
--
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: PROBLEM: PS/2 keyboard does not work with 2.6.15
2006-01-05 13:58 Martin Bretschneider
@ 2006-01-05 14:37 ` Dmitry Torokhov
2006-01-06 7:21 ` Jan Engelhardt
` (2 subsequent siblings)
3 siblings, 0 replies; 32+ messages in thread
From: Dmitry Torokhov @ 2006-01-05 14:37 UTC (permalink / raw)
To: Martin Bretschneider; +Cc: linux-kernel
On 1/5/06, Martin Bretschneider <mailing-lists-mmv@bretschneidernet.de> wrote:
> Hi kernel-devs,
>
> [1.]
> a keyboard that is connected to to PS/2 port does not work with
> kernel 2.6.15. That is to say that no action is seen at the login
> promt if I enter any key.
>
Could you please boot with "i8042.debug", then reboot and send me
/var/log/messages or whatever file your syslog dumps kernel messages?
Thanks!
--
Dmitry
^ permalink raw reply [flat|nested] 32+ messages in thread
* PROBLEM: PS/2 keyboard does not work with 2.6.15
@ 2006-01-05 13:58 Martin Bretschneider
2006-01-05 14:37 ` Dmitry Torokhov
` (3 more replies)
0 siblings, 4 replies; 32+ messages in thread
From: Martin Bretschneider @ 2006-01-05 13:58 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 3148 bytes --]
Hi kernel-devs,
[1.]
a keyboard that is connected to to PS/2 port does not work with
kernel 2.6.15. That is to say that no action is seen at the login
promt if I enter any key.
[2.]
I used PS/2 keyboards for a long time with kernels < 2.6.15
like 2.6.14.2, 2.6.13 or 2.6.11.10. I used "make oldconfig" to move
the .config file form 2.6.14.2 to 2.6.15 and answered "no" to every
question¹
The keyboard is pluged the right way since I can walk around in the
lilo menu before the kernel is being loaded. If I choose another
kernel the PS/2 keyboard does work. I can connect to the pc with a
running 2.6.15 from another pc using ssh. Everything looks normal,
there are no strange errors in /var/log/syslog or from the output
dmesg. I can also use the soundcard...
I also tried another keyboard that do work on kernels < 2.6.15 with
no success.
I cannot tell if the PS/2 mouse does not work either since I cannot
start X.
[3.]
PS/2 keyboard, input
[4.] cat /proc/version
Linux version 2.6.15-06.01.03 (root@mars.bretschneidernet.de)
(gcc-Version 4.0.3 20051201 (prerelease) (Debian 4.0.2-5)) #1 PREEMPT
Tue Jan 3 20:50:32 CET 2006
[5.]
2.6.14.2
[8.1] ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux mars.bretschneidernet.de 2.6.15-06.01.03 #1 PREEMPT Tue Jan 3
20:50:32 CET 2006 i686 GNU/Linux
Gnu C 4.0.3
Gnu make 3.81beta4
binutils 2.16.91
util-linux 2.12p
mount 2.12p
module-init-tools 3.2.2
e2fsprogs 1.38
reiserfsprogs line
reiser4progs line
xfsprogs 2.6.28
PPP 2.4.4b1
Linux C Library 2.3.5
Dynamic linker (ldd) 2.3.5
Procps 3.1.14
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 5.93
udev 079
Modules Loaded parport_pc lp parport binfmt_misc rfcomm l2cap
bluetooth ipt_state ip_conntrack nfnetlink iptable_filter ip_tables
nls_iso8859_1 nls_cp437 vfat fat isofs it87 hwmon_vid hwmon i2c_isa
cryptoloop loop ppp_deflate zlib_deflate zlib_inflate bsd_comp
ppp_generic slhc thermal processor snd_emu10k1_synth snd_emux_synth
snd_seq_virmidi snd_seq_midi_emul snd_seq_oss snd_seq_midi
snd_seq_midi_event snd_seq snd_emu10k1 snd_rawmidi snd_seq_device
snd_ac97_codec snd_pcm_oss snd_mixer_oss snd_pcm snd_timer
snd_ac97_bus snd_page_alloc snd_util_mem snd_hwdep ehci_hcd ohci_hcd
forcedeth usbcore i2c_nforce2 i2c_core
[other information are attached]
[8.7.]
The motherboard is a Gigabyte GA-K8NF-9 using the nforce4 chipset.
The CPU in an AMD64 that does only run in the 32bit mode.
Kind regards from Martin
[1] The .config files can be seen on
http://www.bretschneidernet.de/tmp/config-2.6.14.2 and
http://www.bretschneidernet.de/tmp/config-2.6.15
--
http://www.bretschneidernet.de OpenPGP-key: 0x4EA52583
(o__ (O_ Philip R. Zimmermann:
//\' //\ If privacy is outlawed,
V_/_ V_/_ only outlaws will have privacy.
[-- Attachment #2: more_information.txt.gz --]
[-- Type: application/x-gzip, Size: 4138 bytes --]
^ permalink raw reply [flat|nested] 32+ messages in thread
end of thread, other threads:[~2006-02-04 11:30 UTC | newest]
Thread overview: 32+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2006-01-14 14:20 PROBLEM: PS/2 keyboard does not work with 2.6.15 Walt H
2006-01-14 17:09 ` Alan Stern
2006-01-14 19:27 ` Walt H
2006-01-15 15:45 ` Alan Stern
-- strict thread matches above, loose matches on Subject: below --
2006-01-09 6:10 Leonid
2006-01-05 13:58 Martin Bretschneider
2006-01-05 14:37 ` Dmitry Torokhov
2006-01-06 7:21 ` Jan Engelhardt
2006-01-06 16:29 ` Martin Bretschneider
2006-01-06 19:00 ` Jesper Juhl
2006-01-08 21:23 ` Martin Bretschneider
2006-01-08 22:19 ` Dmitry Torokhov
2006-01-09 9:50 ` Martin Bretschneider
2006-01-09 6:26 ` Dmitry Torokhov
2006-01-09 15:32 ` Alan Stern
2006-01-09 16:50 ` Dmitry Torokhov
2006-01-09 17:23 ` Alan Stern
2006-01-09 17:54 ` Dmitry Torokhov
2006-01-09 20:08 ` Martin Bretschneider
2006-02-04 7:01 ` mahesh
2006-01-10 7:43 ` Vojtech Pavlik
2006-01-10 15:12 ` Alan Stern
2006-01-10 15:28 ` Vojtech Pavlik
2006-01-10 15:37 ` Dmitry Torokhov
2006-01-11 0:01 ` Jan Rekorajski
2006-01-11 0:19 ` Pete Zaitcev
2006-01-11 15:26 ` Alan Stern
2006-01-11 16:01 ` Jan Rekorajski
2006-01-11 19:57 ` Pete Zaitcev
[not found] ` <161717d50601101019k34a901a8x37fb28187a609490@mail.gmail.com>
[not found] ` <d120d5000601101225h32b44f7eobae654056cf0318c@mail.gmail.com>
[not found] ` <161717d50601101419q373cde76y6b374f1ae289ca22@mail.gmail.com>
[not found] ` <d120d5000601101425g576f8fd3kc9de80a4b320c3bf@mail.gmail.com>
2006-01-11 2:45 ` Dave Neuer
2006-01-09 18:36 ` Martin Bretschneider
2006-01-09 19:09 ` Alan Stern
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).