[PATCH v3 0/9] Support Runtime PM and host mode by Tegra ChipIdea USB driver

[PATCH v3 0/9] Support Runtime PM and host mode by Tegra ChipIdea USB driver

[Dmitry Osipenko]

This series implements Runtime PM support for the Tegra ChipIdea USB driver.
It also squashes the older ehci-tegra driver into the ChipIdea driver, hence
the RPM is supported by both UDC and host controllers, secondly this opens
opportunity for implementing OTG support in the future.

Patchset was tested on various Tegra20, Tegra30 and Tegra124 devices.
Thanks to Peter Geis, Matt Merhar, Nicolas Chauvet and Ion Agorria for
helping with the extensive and productive testing!

Changelog:

v3: - Replaced "goto" with if-statements as was suggested by Thierry Reding.

    - Improved wording of the deprecated Kconfig entry as was suggested
      by Alan Stern.

    - Added ACKs from Thierry Reding and Alan Stern.

    - Added a new minor patch "Specify TX FIFO threshold in UDC SoC info"
      just for completeness, since we can now switch OTG to host mode in
      the ChipIdea driver. Although, OTG support remains a work-in-progress
      for now.

v2: - Improved comments in the code as it was suggested by Peter Chen and
      Sergei Shtylyov for v1.

    - Replaced mdelay() with fsleep() and made ci->hdc to reset to NULL in
      a error code path, like it was suggested by Peter Chen.

    - Redirected deprecated USB_EHCI_TEGRA Kconfig entry to USB_CHIPIDEA_TEGRA
      as was suggested by Alan Stern.

    - Improved commit message and added ACK from Thierry Reding to the patch
      that removes MODULE_ALIAS.

    - Fixed UDC PHY waking up on ASUS TF201 tablet device by utilizing
      additional VBUS sensor. This was reported and tested by Ion Agorria.

    - Added t-b from Ion Agorria.

Dmitry Osipenko (8):
  usb: phy: tegra: Add delay after power up
  usb: phy: tegra: Support waking up from a low power mode
  usb: chipidea: tegra: Remove MODULE_ALIAS
  usb: chipidea: tegra: Rename UDC to USB
  usb: chipidea: tegra: Support runtime PM
  usb: chipidea: tegra: Specify TX FIFO threshold in UDC SoC info
  usb: host: ehci-tegra: Remove the driver
  ARM: tegra_defconfig: Enable USB_CHIPIDEA_HOST and remove
    USB_EHCI_TEGRA

Peter Geis (1):
  usb: chipidea: tegra: Support host mode

 arch/arm/configs/tegra_defconfig     |   3 +-
 drivers/usb/chipidea/Kconfig         |   3 +-
 drivers/usb/chipidea/ci_hdrc_tegra.c | 344 ++++++++++++---
 drivers/usb/chipidea/core.c          |  10 +-
 drivers/usb/chipidea/host.c          | 104 ++++-
 drivers/usb/host/Kconfig             |  10 +-
 drivers/usb/host/Makefile            |   1 -
 drivers/usb/host/ehci-tegra.c        | 604 ---------------------------
 drivers/usb/phy/phy-tegra-usb.c      | 103 ++++-
 include/linux/usb/chipidea.h         |   6 +
 include/linux/usb/tegra_usb_phy.h    |   2 +
 11 files changed, 518 insertions(+), 672 deletions(-)
 delete mode 100644 drivers/usb/host/ehci-tegra.c

-- 
2.29.2

[PATCH v3 1/9] usb: phy: tegra: Add delay after power up

[Dmitry Osipenko]

The PHY hardware needs the delay of 2ms after power up, otherwise initial
interrupt may be lost if USB controller is accessed before PHY is settled
down. Previously this issue was masked by implicit delays, but now it pops
up after squashing the older ehci-tegra driver into the ChipIdea driver.

Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
---
 drivers/usb/phy/phy-tegra-usb.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/usb/phy/phy-tegra-usb.c b/drivers/usb/phy/phy-tegra-usb.c
index 03a333797382..1296524e1bee 100644
--- a/drivers/usb/phy/phy-tegra-usb.c
+++ b/drivers/usb/phy/phy-tegra-usb.c
@@ -784,6 +784,9 @@ static int tegra_usb_phy_power_on(struct tegra_usb_phy *phy)
 
 	phy->powered_on = true;
 
+	/* Let PHY settle down */
+	usleep_range(2000, 2500);
+
 	return 0;
 }
 
-- 
2.29.2

[PATCH v3 2/9] usb: phy: tegra: Support waking up from a low power mode

[Dmitry Osipenko]

Support programming of waking up from a low power mode by implementing the
generic set_wakeup() callback of the USB PHY API.

Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
---
 drivers/usb/phy/phy-tegra-usb.c   | 100 ++++++++++++++++++++++++++----
 include/linux/usb/tegra_usb_phy.h |   2 +
 2 files changed, 91 insertions(+), 11 deletions(-)

diff --git a/drivers/usb/phy/phy-tegra-usb.c b/drivers/usb/phy/phy-tegra-usb.c
index 1296524e1bee..a48452a6172b 100644
--- a/drivers/usb/phy/phy-tegra-usb.c
+++ b/drivers/usb/phy/phy-tegra-usb.c
@@ -45,6 +45,7 @@
 #define TEGRA_PORTSC1_RWC_BITS	(PORT_CSC | PORT_PEC | PORT_OCC)
 
 #define USB_SUSP_CTRL				0x400
+#define   USB_WAKE_ON_RESUME_EN			BIT(2)
 #define   USB_WAKE_ON_CNNT_EN_DEV		BIT(3)
 #define   USB_WAKE_ON_DISCON_EN_DEV		BIT(4)
 #define   USB_SUSP_CLR				BIT(5)
@@ -56,6 +57,15 @@
 #define   USB_SUSP_SET				BIT(14)
 #define   USB_WAKEUP_DEBOUNCE_COUNT(x)		(((x) & 0x7) << 16)
 
+#define USB_PHY_VBUS_SENSORS			0x404
+#define   B_SESS_VLD_WAKEUP_EN			BIT(6)
+#define   B_VBUS_VLD_WAKEUP_EN			BIT(14)
+#define   A_SESS_VLD_WAKEUP_EN			BIT(22)
+#define   A_VBUS_VLD_WAKEUP_EN			BIT(30)
+
+#define USB_PHY_VBUS_WAKEUP_ID			0x408
+#define   VBUS_WAKEUP_WAKEUP_EN			BIT(30)
+
 #define USB1_LEGACY_CTRL			0x410
 #define   USB1_NO_LEGACY_MODE			BIT(0)
 #define   USB1_VBUS_SENSE_CTL_MASK		(3 << 1)
@@ -334,6 +344,11 @@ static int utmip_pad_power_on(struct tegra_usb_phy *phy)
 		writel_relaxed(val, base + UTMIP_BIAS_CFG0);
 	}
 
+	if (phy->pad_wakeup) {
+		phy->pad_wakeup = false;
+		utmip_pad_count--;
+	}
+
 	spin_unlock(&utmip_pad_lock);
 
 	clk_disable_unprepare(phy->pad_clk);
@@ -359,6 +374,17 @@ static int utmip_pad_power_off(struct tegra_usb_phy *phy)
 		goto ulock;
 	}
 
+	/*
+	 * In accordance to TRM, OTG and Bias pad circuits could be turned off
+	 * to save power if wake is enabled, but the VBUS-change detection
+	 * method is board-specific and these circuits may need to be enabled
+	 * to generate wakeup event, hence we will just keep them both enabled.
+	 */
+	if (phy->wakeup_enabled) {
+		phy->pad_wakeup = true;
+		utmip_pad_count++;
+	}
+
 	if (--utmip_pad_count == 0) {
 		val = readl_relaxed(base + UTMIP_BIAS_CFG0);
 		val |= UTMIP_OTGPD | UTMIP_BIASPD;
@@ -503,11 +529,24 @@ static int utmi_phy_power_on(struct tegra_usb_phy *phy)
 		writel_relaxed(val, base + UTMIP_PLL_CFG1);
 	}
 
+	val = readl_relaxed(base + USB_SUSP_CTRL);
+	val &= ~USB_WAKE_ON_RESUME_EN;
+	writel_relaxed(val, base + USB_SUSP_CTRL);
+
 	if (phy->mode == USB_DR_MODE_PERIPHERAL) {
 		val = readl_relaxed(base + USB_SUSP_CTRL);
 		val &= ~(USB_WAKE_ON_CNNT_EN_DEV | USB_WAKE_ON_DISCON_EN_DEV);
 		writel_relaxed(val, base + USB_SUSP_CTRL);
 
+		val = readl_relaxed(base + USB_PHY_VBUS_WAKEUP_ID);
+		val &= ~VBUS_WAKEUP_WAKEUP_EN;
+		writel_relaxed(val, base + USB_PHY_VBUS_WAKEUP_ID);
+
+		val = readl_relaxed(base + USB_PHY_VBUS_SENSORS);
+		val &= ~(A_VBUS_VLD_WAKEUP_EN | A_SESS_VLD_WAKEUP_EN);
+		val &= ~(B_VBUS_VLD_WAKEUP_EN | B_SESS_VLD_WAKEUP_EN);
+		writel_relaxed(val, base + USB_PHY_VBUS_SENSORS);
+
 		val = readl_relaxed(base + UTMIP_BAT_CHRG_CFG0);
 		val &= ~UTMIP_PD_CHRG;
 		writel_relaxed(val, base + UTMIP_BAT_CHRG_CFG0);
@@ -605,31 +644,51 @@ static int utmi_phy_power_off(struct tegra_usb_phy *phy)
 
 	utmi_phy_clk_disable(phy);
 
-	if (phy->mode == USB_DR_MODE_PERIPHERAL) {
+	/* PHY won't resume if reset is asserted */
+	if (!phy->wakeup_enabled) {
 		val = readl_relaxed(base + USB_SUSP_CTRL);
-		val &= ~USB_WAKEUP_DEBOUNCE_COUNT(~0);
-		val |= USB_WAKE_ON_CNNT_EN_DEV | USB_WAKEUP_DEBOUNCE_COUNT(5);
+		val |= UTMIP_RESET;
 		writel_relaxed(val, base + USB_SUSP_CTRL);
 	}
 
-	val = readl_relaxed(base + USB_SUSP_CTRL);
-	val |= UTMIP_RESET;
-	writel_relaxed(val, base + USB_SUSP_CTRL);
-
 	val = readl_relaxed(base + UTMIP_BAT_CHRG_CFG0);
 	val |= UTMIP_PD_CHRG;
 	writel_relaxed(val, base + UTMIP_BAT_CHRG_CFG0);
 
-	val = readl_relaxed(base + UTMIP_XCVR_CFG0);
-	val |= UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN |
-	       UTMIP_FORCE_PDZI_POWERDOWN;
-	writel_relaxed(val, base + UTMIP_XCVR_CFG0);
+	if (!phy->wakeup_enabled) {
+		val = readl_relaxed(base + UTMIP_XCVR_CFG0);
+		val |= UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN |
+		       UTMIP_FORCE_PDZI_POWERDOWN;
+		writel_relaxed(val, base + UTMIP_XCVR_CFG0);
+	}
 
 	val = readl_relaxed(base + UTMIP_XCVR_CFG1);
 	val |= UTMIP_FORCE_PDDISC_POWERDOWN | UTMIP_FORCE_PDCHRP_POWERDOWN |
 	       UTMIP_FORCE_PDDR_POWERDOWN;
 	writel_relaxed(val, base + UTMIP_XCVR_CFG1);
 
+	if (phy->wakeup_enabled) {
+		val = readl_relaxed(base + USB_SUSP_CTRL);
+		val &= ~USB_WAKEUP_DEBOUNCE_COUNT(~0);
+		val |= USB_WAKEUP_DEBOUNCE_COUNT(5);
+		val |= USB_WAKE_ON_RESUME_EN;
+		writel_relaxed(val, base + USB_SUSP_CTRL);
+
+		/*
+		 * Ask VBUS sensor to generate wake event once cable is
+		 * connected.
+		 */
+		if (phy->mode == USB_DR_MODE_PERIPHERAL) {
+			val = readl_relaxed(base + USB_PHY_VBUS_WAKEUP_ID);
+			val |= VBUS_WAKEUP_WAKEUP_EN;
+			writel_relaxed(val, base + USB_PHY_VBUS_WAKEUP_ID);
+
+			val = readl_relaxed(base + USB_PHY_VBUS_SENSORS);
+			val |= A_VBUS_VLD_WAKEUP_EN;
+			writel_relaxed(val, base + USB_PHY_VBUS_SENSORS);
+		}
+	}
+
 	return utmip_pad_power_off(phy);
 }
 
@@ -765,6 +824,15 @@ static int ulpi_phy_power_off(struct tegra_usb_phy *phy)
 	usleep_range(5000, 6000);
 	clk_disable_unprepare(phy->clk);
 
+	/*
+	 * Wakeup currently unimplemented for ULPI, thus PHY needs to be
+	 * force-resumed.
+	 */
+	if (WARN_ON_ONCE(phy->wakeup_enabled)) {
+		ulpi_phy_power_on(phy);
+		return -EOPNOTSUPP;
+	}
+
 	return 0;
 }
 
@@ -827,6 +895,15 @@ static void tegra_usb_phy_shutdown(struct usb_phy *u_phy)
 	phy->freq = NULL;
 }
 
+static int tegra_usb_phy_set_wakeup(struct usb_phy *u_phy, bool enable)
+{
+	struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy);
+
+	phy->wakeup_enabled = enable;
+
+	return 0;
+}
+
 static int tegra_usb_phy_set_suspend(struct usb_phy *u_phy, int suspend)
 {
 	struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy);
@@ -1198,6 +1275,7 @@ static int tegra_usb_phy_probe(struct platform_device *pdev)
 	tegra_phy->u_phy.dev = &pdev->dev;
 	tegra_phy->u_phy.init = tegra_usb_phy_init;
 	tegra_phy->u_phy.shutdown = tegra_usb_phy_shutdown;
+	tegra_phy->u_phy.set_wakeup = tegra_usb_phy_set_wakeup;
 	tegra_phy->u_phy.set_suspend = tegra_usb_phy_set_suspend;
 
 	platform_set_drvdata(pdev, tegra_phy);
diff --git a/include/linux/usb/tegra_usb_phy.h b/include/linux/usb/tegra_usb_phy.h
index c29d1b4c9381..fd1c9f6a4e37 100644
--- a/include/linux/usb/tegra_usb_phy.h
+++ b/include/linux/usb/tegra_usb_phy.h
@@ -79,6 +79,8 @@ struct tegra_usb_phy {
 	bool is_ulpi_phy;
 	struct gpio_desc *reset_gpio;
 	struct reset_control *pad_rst;
+	bool wakeup_enabled;
+	bool pad_wakeup;
 	bool powered_on;
 };
 
-- 
2.29.2

[PATCH v3 3/9] usb: chipidea: tegra: Remove MODULE_ALIAS

[Dmitry Osipenko]

The OF core adds an alias based on the OF device ID table, which is enough
to have the driver autoloaded. The legacy MODULE_ALIAS macro was relevant
to a pre-OF board files which manually created platform devices, this is
irrelevant to the modern ARM kernels since devices are created by the OF
core. Remove the unnecessary macro in order to keep the driver's code
cleaner.

Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
---
 drivers/usb/chipidea/ci_hdrc_tegra.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/usb/chipidea/ci_hdrc_tegra.c b/drivers/usb/chipidea/ci_hdrc_tegra.c
index 7455df0ede49..10eaaba2a3f0 100644
--- a/drivers/usb/chipidea/ci_hdrc_tegra.c
+++ b/drivers/usb/chipidea/ci_hdrc_tegra.c
@@ -128,5 +128,4 @@ module_platform_driver(tegra_udc_driver);
 
 MODULE_DESCRIPTION("NVIDIA Tegra USB device mode driver");
 MODULE_AUTHOR("Thierry Reding <treding@nvidia.com>");
-MODULE_ALIAS("platform:tegra-udc");
 MODULE_LICENSE("GPL v2");
-- 
2.29.2

[PATCH v3 4/9] usb: chipidea: tegra: Rename UDC to USB

[Dmitry Osipenko]

Rename all occurrences in the code from "udc" to "usb" and change the
Kconfig entry in order to show that this driver supports USB modes other
than device-only mode. The follow up patch will add host-mode support and
it will be cleaner to perform the renaming separately, i.e. in this patch.

Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
---
 drivers/usb/chipidea/Kconfig         |  2 +-
 drivers/usb/chipidea/ci_hdrc_tegra.c | 78 ++++++++++++++--------------
 2 files changed, 40 insertions(+), 40 deletions(-)

diff --git a/drivers/usb/chipidea/Kconfig b/drivers/usb/chipidea/Kconfig
index 8bafcfc6080d..8685ead6ccc7 100644
--- a/drivers/usb/chipidea/Kconfig
+++ b/drivers/usb/chipidea/Kconfig
@@ -53,7 +53,7 @@ config USB_CHIPIDEA_GENERIC
 	default USB_CHIPIDEA
 
 config USB_CHIPIDEA_TEGRA
-	tristate "Enable Tegra UDC glue driver" if EMBEDDED
+	tristate "Enable Tegra USB glue driver" if EMBEDDED
 	depends on OF
 	depends on USB_CHIPIDEA_UDC
 	default USB_CHIPIDEA
diff --git a/drivers/usb/chipidea/ci_hdrc_tegra.c b/drivers/usb/chipidea/ci_hdrc_tegra.c
index 10eaaba2a3f0..d8efa80aa1c2 100644
--- a/drivers/usb/chipidea/ci_hdrc_tegra.c
+++ b/drivers/usb/chipidea/ci_hdrc_tegra.c
@@ -12,7 +12,7 @@
 
 #include "ci.h"
 
-struct tegra_udc {
+struct tegra_usb {
 	struct ci_hdrc_platform_data data;
 	struct platform_device *dev;
 
@@ -20,15 +20,15 @@ struct tegra_udc {
 	struct clk *clk;
 };
 
-struct tegra_udc_soc_info {
+struct tegra_usb_soc_info {
 	unsigned long flags;
 };
 
-static const struct tegra_udc_soc_info tegra_udc_soc_info = {
+static const struct tegra_usb_soc_info tegra_udc_soc_info = {
 	.flags = CI_HDRC_REQUIRES_ALIGNED_DMA,
 };
 
-static const struct of_device_id tegra_udc_of_match[] = {
+static const struct of_device_id tegra_usb_of_match[] = {
 	{
 		.compatible = "nvidia,tegra20-udc",
 		.data = &tegra_udc_soc_info,
@@ -45,16 +45,16 @@ static const struct of_device_id tegra_udc_of_match[] = {
 		/* sentinel */
 	}
 };
-MODULE_DEVICE_TABLE(of, tegra_udc_of_match);
+MODULE_DEVICE_TABLE(of, tegra_usb_of_match);
 
-static int tegra_udc_probe(struct platform_device *pdev)
+static int tegra_usb_probe(struct platform_device *pdev)
 {
-	const struct tegra_udc_soc_info *soc;
-	struct tegra_udc *udc;
+	const struct tegra_usb_soc_info *soc;
+	struct tegra_usb *usb;
 	int err;
 
-	udc = devm_kzalloc(&pdev->dev, sizeof(*udc), GFP_KERNEL);
-	if (!udc)
+	usb = devm_kzalloc(&pdev->dev, sizeof(*usb), GFP_KERNEL);
+	if (!usb)
 		return -ENOMEM;
 
 	soc = of_device_get_match_data(&pdev->dev);
@@ -63,69 +63,69 @@ static int tegra_udc_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	udc->phy = devm_usb_get_phy_by_phandle(&pdev->dev, "nvidia,phy", 0);
-	if (IS_ERR(udc->phy)) {
-		err = PTR_ERR(udc->phy);
+	usb->phy = devm_usb_get_phy_by_phandle(&pdev->dev, "nvidia,phy", 0);
+	if (IS_ERR(usb->phy)) {
+		err = PTR_ERR(usb->phy);
 		dev_err(&pdev->dev, "failed to get PHY: %d\n", err);
 		return err;
 	}
 
-	udc->clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(udc->clk)) {
-		err = PTR_ERR(udc->clk);
+	usb->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(usb->clk)) {
+		err = PTR_ERR(usb->clk);
 		dev_err(&pdev->dev, "failed to get clock: %d\n", err);
 		return err;
 	}
 
-	err = clk_prepare_enable(udc->clk);
+	err = clk_prepare_enable(usb->clk);
 	if (err < 0) {
 		dev_err(&pdev->dev, "failed to enable clock: %d\n", err);
 		return err;
 	}
 
 	/* setup and register ChipIdea HDRC device */
-	udc->data.name = "tegra-udc";
-	udc->data.flags = soc->flags;
-	udc->data.usb_phy = udc->phy;
-	udc->data.capoffset = DEF_CAPOFFSET;
-
-	udc->dev = ci_hdrc_add_device(&pdev->dev, pdev->resource,
-				      pdev->num_resources, &udc->data);
-	if (IS_ERR(udc->dev)) {
-		err = PTR_ERR(udc->dev);
+	usb->data.name = "tegra-usb";
+	usb->data.flags = soc->flags;
+	usb->data.usb_phy = usb->phy;
+	usb->data.capoffset = DEF_CAPOFFSET;
+
+	usb->dev = ci_hdrc_add_device(&pdev->dev, pdev->resource,
+				      pdev->num_resources, &usb->data);
+	if (IS_ERR(usb->dev)) {
+		err = PTR_ERR(usb->dev);
 		dev_err(&pdev->dev, "failed to add HDRC device: %d\n", err);
 		goto fail_power_off;
 	}
 
-	platform_set_drvdata(pdev, udc);
+	platform_set_drvdata(pdev, usb);
 
 	return 0;
 
 fail_power_off:
-	clk_disable_unprepare(udc->clk);
+	clk_disable_unprepare(usb->clk);
 	return err;
 }
 
-static int tegra_udc_remove(struct platform_device *pdev)
+static int tegra_usb_remove(struct platform_device *pdev)
 {
-	struct tegra_udc *udc = platform_get_drvdata(pdev);
+	struct tegra_usb *usb = platform_get_drvdata(pdev);
 
-	ci_hdrc_remove_device(udc->dev);
-	clk_disable_unprepare(udc->clk);
+	ci_hdrc_remove_device(usb->dev);
+	clk_disable_unprepare(usb->clk);
 
 	return 0;
 }
 
-static struct platform_driver tegra_udc_driver = {
+static struct platform_driver tegra_usb_driver = {
 	.driver = {
-		.name = "tegra-udc",
-		.of_match_table = tegra_udc_of_match,
+		.name = "tegra-usb",
+		.of_match_table = tegra_usb_of_match,
 	},
-	.probe = tegra_udc_probe,
-	.remove = tegra_udc_remove,
+	.probe = tegra_usb_probe,
+	.remove = tegra_usb_remove,
 };
-module_platform_driver(tegra_udc_driver);
+module_platform_driver(tegra_usb_driver);
 
-MODULE_DESCRIPTION("NVIDIA Tegra USB device mode driver");
+MODULE_DESCRIPTION("NVIDIA Tegra USB driver");
 MODULE_AUTHOR("Thierry Reding <treding@nvidia.com>");
 MODULE_LICENSE("GPL v2");
-- 
2.29.2

[PATCH v3 5/9] usb: chipidea: tegra: Support host mode

[Dmitry Osipenko]

From: Peter Geis <pgwipeout@gmail.com>

Add USB host mode to the Tegra HDRC driver. This allows us to benefit from
support provided by the generic ChipIdea driver instead of duplicating the
effort in a separate ehci-tegra driver.

Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
---
 drivers/usb/chipidea/Kconfig         |   1 -
 drivers/usb/chipidea/ci_hdrc_tegra.c | 243 ++++++++++++++++++++++++++-
 drivers/usb/chipidea/core.c          |  10 +-
 drivers/usb/chipidea/host.c          | 104 +++++++++++-
 include/linux/usb/chipidea.h         |   6 +
 5 files changed, 356 insertions(+), 8 deletions(-)

diff --git a/drivers/usb/chipidea/Kconfig b/drivers/usb/chipidea/Kconfig
index 8685ead6ccc7..661818e8fed6 100644
--- a/drivers/usb/chipidea/Kconfig
+++ b/drivers/usb/chipidea/Kconfig
@@ -55,7 +55,6 @@ config USB_CHIPIDEA_GENERIC
 config USB_CHIPIDEA_TEGRA
 	tristate "Enable Tegra USB glue driver" if EMBEDDED
 	depends on OF
-	depends on USB_CHIPIDEA_UDC
 	default USB_CHIPIDEA
 
 endif
diff --git a/drivers/usb/chipidea/ci_hdrc_tegra.c b/drivers/usb/chipidea/ci_hdrc_tegra.c
index d8efa80aa1c2..5fccdeeefc64 100644
--- a/drivers/usb/chipidea/ci_hdrc_tegra.c
+++ b/drivers/usb/chipidea/ci_hdrc_tegra.c
@@ -4,11 +4,18 @@
  */
 
 #include <linux/clk.h>
+#include <linux/io.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/reset.h>
 
+#include <linux/usb.h>
 #include <linux/usb/chipidea.h>
+#include <linux/usb/hcd.h>
+#include <linux/usb/of.h>
+#include <linux/usb/phy.h>
+
+#include "../host/ehci.h"
 
 #include "ci.h"
 
@@ -16,20 +23,47 @@ struct tegra_usb {
 	struct ci_hdrc_platform_data data;
 	struct platform_device *dev;
 
+	const struct tegra_usb_soc_info *soc;
 	struct usb_phy *phy;
 	struct clk *clk;
+
+	bool needs_double_reset;
 };
 
 struct tegra_usb_soc_info {
 	unsigned long flags;
+	unsigned int txfifothresh;
+	enum usb_dr_mode dr_mode;
+};
+
+static const struct tegra_usb_soc_info tegra20_ehci_soc_info = {
+	.flags = CI_HDRC_REQUIRES_ALIGNED_DMA |
+		 CI_HDRC_OVERRIDE_PHY_CONTROL,
+	.dr_mode = USB_DR_MODE_HOST,
+	.txfifothresh = 10,
+};
+
+static const struct tegra_usb_soc_info tegra30_ehci_soc_info = {
+	.flags = CI_HDRC_REQUIRES_ALIGNED_DMA |
+		 CI_HDRC_OVERRIDE_PHY_CONTROL,
+	.dr_mode = USB_DR_MODE_HOST,
+	.txfifothresh = 16,
 };
 
 static const struct tegra_usb_soc_info tegra_udc_soc_info = {
-	.flags = CI_HDRC_REQUIRES_ALIGNED_DMA,
+	.flags = CI_HDRC_REQUIRES_ALIGNED_DMA |
+		 CI_HDRC_OVERRIDE_PHY_CONTROL,
+	.dr_mode = USB_DR_MODE_UNKNOWN,
 };
 
 static const struct of_device_id tegra_usb_of_match[] = {
 	{
+		.compatible = "nvidia,tegra20-ehci",
+		.data = &tegra20_ehci_soc_info,
+	}, {
+		.compatible = "nvidia,tegra30-ehci",
+		.data = &tegra30_ehci_soc_info,
+	}, {
 		.compatible = "nvidia,tegra20-udc",
 		.data = &tegra_udc_soc_info,
 	}, {
@@ -47,6 +81,181 @@ static const struct of_device_id tegra_usb_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, tegra_usb_of_match);
 
+static int tegra_usb_reset_controller(struct device *dev)
+{
+	struct reset_control *rst, *rst_utmi;
+	struct device_node *phy_np;
+	int err;
+
+	rst = devm_reset_control_get_shared(dev, "usb");
+	if (IS_ERR(rst)) {
+		dev_err(dev, "can't get ehci reset: %pe\n", rst);
+		return PTR_ERR(rst);
+	}
+
+	phy_np = of_parse_phandle(dev->of_node, "nvidia,phy", 0);
+	if (!phy_np)
+		return -ENOENT;
+
+	/*
+	 * The 1st USB controller contains some UTMI pad registers that are
+	 * global for all the controllers on the chip. Those registers are
+	 * also cleared when reset is asserted to the 1st controller.
+	 */
+	rst_utmi = of_reset_control_get_shared(phy_np, "utmi-pads");
+	if (IS_ERR(rst_utmi)) {
+		dev_warn(dev, "can't get utmi-pads reset from the PHY\n");
+		dev_warn(dev, "continuing, but please update your DT\n");
+	} else {
+		/*
+		 * PHY driver performs UTMI-pads reset in a case of a
+		 * non-legacy DT.
+		 */
+		reset_control_put(rst_utmi);
+	}
+
+	of_node_put(phy_np);
+
+	/* reset control is shared, hence initialize it first */
+	err = reset_control_deassert(rst);
+	if (err)
+		return err;
+
+	err = reset_control_assert(rst);
+	if (err)
+		return err;
+
+	udelay(1);
+
+	err = reset_control_deassert(rst);
+	if (err)
+		return err;
+
+	return 0;
+}
+
+static int tegra_usb_notify_event(struct ci_hdrc *ci, unsigned int event)
+{
+	struct tegra_usb *usb = dev_get_drvdata(ci->dev->parent);
+	struct ehci_hcd *ehci;
+
+	switch (event) {
+	case CI_HDRC_CONTROLLER_RESET_EVENT:
+		if (ci->hcd) {
+			ehci = hcd_to_ehci(ci->hcd);
+			ehci->has_tdi_phy_lpm = false;
+			ehci_writel(ehci, usb->soc->txfifothresh << 16,
+				    &ehci->regs->txfill_tuning);
+		}
+		break;
+	}
+
+	return 0;
+}
+
+static int tegra_usb_internal_port_reset(struct ehci_hcd *ehci,
+					 u32 __iomem *portsc_reg,
+					 unsigned long *flags)
+{
+	u32 saved_usbintr, temp;
+	unsigned int i, tries;
+	int retval = 0;
+
+	saved_usbintr = ehci_readl(ehci, &ehci->regs->intr_enable);
+	/* disable USB interrupt */
+	ehci_writel(ehci, 0, &ehci->regs->intr_enable);
+	spin_unlock_irqrestore(&ehci->lock, *flags);
+
+	/*
+	 * Here we have to do Port Reset at most twice for
+	 * Port Enable bit to be set.
+	 */
+	for (i = 0; i < 2; i++) {
+		temp = ehci_readl(ehci, portsc_reg);
+		temp |= PORT_RESET;
+		ehci_writel(ehci, temp, portsc_reg);
+		fsleep(10000);
+		temp &= ~PORT_RESET;
+		ehci_writel(ehci, temp, portsc_reg);
+		fsleep(1000);
+		tries = 100;
+		do {
+			fsleep(1000);
+			/*
+			 * Up to this point, Port Enable bit is
+			 * expected to be set after 2 ms waiting.
+			 * USB1 usually takes extra 45 ms, for safety,
+			 * we take 100 ms as timeout.
+			 */
+			temp = ehci_readl(ehci, portsc_reg);
+		} while (!(temp & PORT_PE) && tries--);
+		if (temp & PORT_PE)
+			break;
+	}
+	if (i == 2)
+		retval = -ETIMEDOUT;
+
+	/*
+	 * Clear Connect Status Change bit if it's set.
+	 * We can't clear PORT_PEC. It will also cause PORT_PE to be cleared.
+	 */
+	if (temp & PORT_CSC)
+		ehci_writel(ehci, PORT_CSC, portsc_reg);
+
+	/*
+	 * Write to clear any interrupt status bits that might be set
+	 * during port reset.
+	 */
+	temp = ehci_readl(ehci, &ehci->regs->status);
+	ehci_writel(ehci, temp, &ehci->regs->status);
+
+	/* restore original interrupt-enable bits */
+	spin_lock_irqsave(&ehci->lock, *flags);
+	ehci_writel(ehci, saved_usbintr, &ehci->regs->intr_enable);
+
+	return retval;
+}
+
+static int tegra_ehci_hub_control(struct ci_hdrc *ci, u16 typeReq, u16 wValue,
+				  u16 wIndex, char *buf, u16 wLength,
+				  bool *done, unsigned long *flags)
+{
+	struct tegra_usb *usb = dev_get_drvdata(ci->dev->parent);
+	struct ehci_hcd *ehci = hcd_to_ehci(ci->hcd);
+	u32 __iomem *status_reg;
+	int retval = 0;
+
+	status_reg = &ehci->regs->port_status[(wIndex & 0xff) - 1];
+
+	switch (typeReq) {
+	case SetPortFeature:
+		if (wValue != USB_PORT_FEAT_RESET || !usb->needs_double_reset)
+			break;
+
+		/* for USB1 port we need to issue Port Reset twice internally */
+		retval = tegra_usb_internal_port_reset(ehci, status_reg, flags);
+		*done  = true;
+		break;
+	}
+
+	return retval;
+}
+
+static void tegra_usb_enter_lpm(struct ci_hdrc *ci, bool enable)
+{
+	/*
+	 * Touching any register which belongs to AHB clock domain will
+	 * hang CPU if USB controller is put into low power mode because
+	 * AHB USB clock is gated on Tegra in the LPM.
+	 *
+	 * Tegra PHY has a separate register for checking the clock status
+	 * and usb_phy_set_suspend() takes care of gating/ungating the clocks
+	 * and restoring the PHY state on Tegra. Hence DEVLC/PORTSC registers
+	 * shouldn't be touched directly by the CI driver.
+	 */
+	usb_phy_set_suspend(ci->usb_phy, enable);
+}
+
 static int tegra_usb_probe(struct platform_device *pdev)
 {
 	const struct tegra_usb_soc_info *soc;
@@ -83,24 +292,49 @@ static int tegra_usb_probe(struct platform_device *pdev)
 		return err;
 	}
 
+	if (device_property_present(&pdev->dev, "nvidia,needs-double-reset"))
+		usb->needs_double_reset = true;
+
+	err = tegra_usb_reset_controller(&pdev->dev);
+	if (err) {
+		dev_err(&pdev->dev, "failed to reset controller: %d\n", err);
+		goto fail_power_off;
+	}
+
+	/*
+	 * USB controller registers shouldn't be touched before PHY is
+	 * initialized, otherwise CPU will hang because clocks are gated.
+	 * PHY driver controls gating of internal USB clocks on Tegra.
+	 */
+	err = usb_phy_init(usb->phy);
+	if (err)
+		goto fail_power_off;
+
+	platform_set_drvdata(pdev, usb);
+
 	/* setup and register ChipIdea HDRC device */
+	usb->soc = soc;
 	usb->data.name = "tegra-usb";
 	usb->data.flags = soc->flags;
 	usb->data.usb_phy = usb->phy;
+	usb->data.dr_mode = soc->dr_mode;
 	usb->data.capoffset = DEF_CAPOFFSET;
+	usb->data.enter_lpm = tegra_usb_enter_lpm;
+	usb->data.hub_control = tegra_ehci_hub_control;
+	usb->data.notify_event = tegra_usb_notify_event;
 
 	usb->dev = ci_hdrc_add_device(&pdev->dev, pdev->resource,
 				      pdev->num_resources, &usb->data);
 	if (IS_ERR(usb->dev)) {
 		err = PTR_ERR(usb->dev);
 		dev_err(&pdev->dev, "failed to add HDRC device: %d\n", err);
-		goto fail_power_off;
+		goto phy_shutdown;
 	}
 
-	platform_set_drvdata(pdev, usb);
-
 	return 0;
 
+phy_shutdown:
+	usb_phy_shutdown(usb->phy);
 fail_power_off:
 	clk_disable_unprepare(usb->clk);
 	return err;
@@ -111,6 +345,7 @@ static int tegra_usb_remove(struct platform_device *pdev)
 	struct tegra_usb *usb = platform_get_drvdata(pdev);
 
 	ci_hdrc_remove_device(usb->dev);
+	usb_phy_shutdown(usb->phy);
 	clk_disable_unprepare(usb->clk);
 
 	return 0;
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index aa40e510b806..3f6c21406dbd 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -195,7 +195,7 @@ static void hw_wait_phy_stable(void)
 }
 
 /* The PHY enters/leaves low power mode */
-static void ci_hdrc_enter_lpm(struct ci_hdrc *ci, bool enable)
+static void ci_hdrc_enter_lpm_common(struct ci_hdrc *ci, bool enable)
 {
 	enum ci_hw_regs reg = ci->hw_bank.lpm ? OP_DEVLC : OP_PORTSC;
 	bool lpm = !!(hw_read(ci, reg, PORTSC_PHCD(ci->hw_bank.lpm)));
@@ -208,6 +208,11 @@ static void ci_hdrc_enter_lpm(struct ci_hdrc *ci, bool enable)
 				0);
 }
 
+static void ci_hdrc_enter_lpm(struct ci_hdrc *ci, bool enable)
+{
+	return ci->platdata->enter_lpm(ci, enable);
+}
+
 static int hw_device_init(struct ci_hdrc *ci, void __iomem *base)
 {
 	u32 reg;
@@ -790,6 +795,9 @@ static int ci_get_platdata(struct device *dev,
 			platdata->pins_device = p;
 	}
 
+	if (!platdata->enter_lpm)
+		platdata->enter_lpm = ci_hdrc_enter_lpm_common;
+
 	return 0;
 }
 
diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c
index 48e4a5ca1835..67247d2ac07a 100644
--- a/drivers/usb/chipidea/host.c
+++ b/drivers/usb/chipidea/host.c
@@ -29,6 +29,12 @@ struct ehci_ci_priv {
 	bool enabled;
 };
 
+struct ci_hdrc_dma_aligned_buffer {
+	void *kmalloc_ptr;
+	void *old_xfer_buffer;
+	u8 data[0];
+};
+
 static int ehci_ci_portpower(struct usb_hcd *hcd, int portnum, bool enable)
 {
 	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
@@ -160,14 +166,15 @@ static int host_start(struct ci_hdrc *ci)
 		pinctrl_select_state(ci->platdata->pctl,
 				     ci->platdata->pins_host);
 
+	ci->hcd = hcd;
+
 	ret = usb_add_hcd(hcd, 0, 0);
 	if (ret) {
+		ci->hcd = NULL;
 		goto disable_reg;
 	} else {
 		struct usb_otg *otg = &ci->otg;
 
-		ci->hcd = hcd;
-
 		if (ci_otg_is_fsm_mode(ci)) {
 			otg->host = &hcd->self;
 			hcd->self.otg_port = 1;
@@ -237,6 +244,7 @@ static int ci_ehci_hub_control(
 	u32		temp;
 	unsigned long	flags;
 	int		retval = 0;
+	bool		done = false;
 	struct device *dev = hcd->self.controller;
 	struct ci_hdrc *ci = dev_get_drvdata(dev);
 
@@ -244,6 +252,13 @@ static int ci_ehci_hub_control(
 
 	spin_lock_irqsave(&ehci->lock, flags);
 
+	if (ci->platdata->hub_control) {
+		retval = ci->platdata->hub_control(ci, typeReq, wValue, wIndex,
+						   buf, wLength, &done, &flags);
+		if (done)
+			goto done;
+	}
+
 	if (typeReq == SetPortFeature && wValue == USB_PORT_FEAT_SUSPEND) {
 		temp = ehci_readl(ehci, status_reg);
 		if ((temp & PORT_PE) == 0 || (temp & PORT_RESET) != 0) {
@@ -349,6 +364,86 @@ static int ci_ehci_bus_suspend(struct usb_hcd *hcd)
 	return 0;
 }
 
+static void ci_hdrc_free_dma_aligned_buffer(struct urb *urb)
+{
+	struct ci_hdrc_dma_aligned_buffer *temp;
+	size_t length;
+
+	if (!(urb->transfer_flags & URB_ALIGNED_TEMP_BUFFER))
+		return;
+
+	temp = container_of(urb->transfer_buffer,
+			    struct ci_hdrc_dma_aligned_buffer, data);
+
+	if (usb_urb_dir_in(urb)) {
+		if (usb_pipeisoc(urb->pipe))
+			length = urb->transfer_buffer_length;
+		else
+			length = urb->actual_length;
+
+		memcpy(temp->old_xfer_buffer, temp->data, length);
+	}
+	urb->transfer_buffer = temp->old_xfer_buffer;
+	kfree(temp->kmalloc_ptr);
+
+	urb->transfer_flags &= ~URB_ALIGNED_TEMP_BUFFER;
+}
+
+static int ci_hdrc_alloc_dma_aligned_buffer(struct urb *urb, gfp_t mem_flags)
+{
+	struct ci_hdrc_dma_aligned_buffer *temp, *kmalloc_ptr;
+	const unsigned int ci_hdrc_usb_dma_align = 32;
+	size_t kmalloc_size;
+
+	if (urb->num_sgs || urb->sg || urb->transfer_buffer_length == 0 ||
+	    !((uintptr_t)urb->transfer_buffer & (ci_hdrc_usb_dma_align - 1)))
+		return 0;
+
+	/* Allocate a buffer with enough padding for alignment */
+	kmalloc_size = urb->transfer_buffer_length +
+		       sizeof(struct ci_hdrc_dma_aligned_buffer) +
+		       ci_hdrc_usb_dma_align - 1;
+
+	kmalloc_ptr = kmalloc(kmalloc_size, mem_flags);
+	if (!kmalloc_ptr)
+		return -ENOMEM;
+
+	/* Position our struct dma_aligned_buffer such that data is aligned */
+	temp = PTR_ALIGN(kmalloc_ptr + 1, ci_hdrc_usb_dma_align) - 1;
+	temp->kmalloc_ptr = kmalloc_ptr;
+	temp->old_xfer_buffer = urb->transfer_buffer;
+	if (usb_urb_dir_out(urb))
+		memcpy(temp->data, urb->transfer_buffer,
+		       urb->transfer_buffer_length);
+	urb->transfer_buffer = temp->data;
+
+	urb->transfer_flags |= URB_ALIGNED_TEMP_BUFFER;
+
+	return 0;
+}
+
+static int ci_hdrc_map_urb_for_dma(struct usb_hcd *hcd, struct urb *urb,
+				   gfp_t mem_flags)
+{
+	int ret;
+
+	ret = ci_hdrc_alloc_dma_aligned_buffer(urb, mem_flags);
+	if (ret)
+		return ret;
+
+	ret = usb_hcd_map_urb_for_dma(hcd, urb, mem_flags);
+	if (ret)
+		ci_hdrc_free_dma_aligned_buffer(urb);
+
+	return ret;
+}
+
+static void ci_hdrc_unmap_urb_for_dma(struct usb_hcd *hcd, struct urb *urb)
+{
+	usb_hcd_unmap_urb_for_dma(hcd, urb);
+	ci_hdrc_free_dma_aligned_buffer(urb);
+}
+
 int ci_hdrc_host_init(struct ci_hdrc *ci)
 {
 	struct ci_role_driver *rdrv;
@@ -366,6 +461,11 @@ int ci_hdrc_host_init(struct ci_hdrc *ci)
 	rdrv->name	= "host";
 	ci->roles[CI_ROLE_HOST] = rdrv;
 
+	if (ci->platdata->flags & CI_HDRC_REQUIRES_ALIGNED_DMA) {
+		ci_ehci_hc_driver.map_urb_for_dma = ci_hdrc_map_urb_for_dma;
+		ci_ehci_hc_driver.unmap_urb_for_dma = ci_hdrc_unmap_urb_for_dma;
+	}
+
 	return 0;
 }
 
diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h
index 025b41687ce9..edf3342507f1 100644
--- a/include/linux/usb/chipidea.h
+++ b/include/linux/usb/chipidea.h
@@ -88,6 +88,12 @@ struct ci_hdrc_platform_data {
 	struct pinctrl_state *pins_default;
 	struct pinctrl_state *pins_host;
 	struct pinctrl_state *pins_device;
+
+	/* platform-specific hooks */
+	int (*hub_control)(struct ci_hdrc *ci, u16 typeReq, u16 wValue,
+			   u16 wIndex, char *buf, u16 wLength,
+			   bool *done, unsigned long *flags);
+	void (*enter_lpm)(struct ci_hdrc *ci, bool enable);
 };
 
 /* Default offset of capability registers */
-- 
2.29.2

[PATCH v3 6/9] usb: chipidea: tegra: Support runtime PM

[Dmitry Osipenko]

Tegra PHY driver now supports waking up controller from a low power mode.
Enable runtime PM in order to put controller into the LPM during idle.

Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
---
 drivers/usb/chipidea/ci_hdrc_tegra.c | 13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/chipidea/ci_hdrc_tegra.c b/drivers/usb/chipidea/ci_hdrc_tegra.c
index 5fccdeeefc64..655671159511 100644
--- a/drivers/usb/chipidea/ci_hdrc_tegra.c
+++ b/drivers/usb/chipidea/ci_hdrc_tegra.c
@@ -38,21 +38,24 @@ struct tegra_usb_soc_info {
 
 static const struct tegra_usb_soc_info tegra20_ehci_soc_info = {
 	.flags = CI_HDRC_REQUIRES_ALIGNED_DMA |
-		 CI_HDRC_OVERRIDE_PHY_CONTROL,
+		 CI_HDRC_OVERRIDE_PHY_CONTROL |
+		 CI_HDRC_SUPPORTS_RUNTIME_PM,
 	.dr_mode = USB_DR_MODE_HOST,
 	.txfifothresh = 10,
 };
 
 static const struct tegra_usb_soc_info tegra30_ehci_soc_info = {
 	.flags = CI_HDRC_REQUIRES_ALIGNED_DMA |
-		 CI_HDRC_OVERRIDE_PHY_CONTROL,
+		 CI_HDRC_OVERRIDE_PHY_CONTROL |
+		 CI_HDRC_SUPPORTS_RUNTIME_PM,
 	.dr_mode = USB_DR_MODE_HOST,
 	.txfifothresh = 16,
 };
 
 static const struct tegra_usb_soc_info tegra_udc_soc_info = {
 	.flags = CI_HDRC_REQUIRES_ALIGNED_DMA |
-		 CI_HDRC_OVERRIDE_PHY_CONTROL,
+		 CI_HDRC_OVERRIDE_PHY_CONTROL |
+		 CI_HDRC_SUPPORTS_RUNTIME_PM,
 	.dr_mode = USB_DR_MODE_UNKNOWN,
 };
 
@@ -323,6 +326,10 @@ static int tegra_usb_probe(struct platform_device *pdev)
 	usb->data.hub_control = tegra_ehci_hub_control;
 	usb->data.notify_event = tegra_usb_notify_event;
 
+	/* Tegra PHY driver currently doesn't support LPM for ULPI */
+	if (of_usb_get_phy_mode(pdev->dev.of_node) == USBPHY_INTERFACE_MODE_ULPI)
+		usb->data.flags &= ~CI_HDRC_SUPPORTS_RUNTIME_PM;
+
 	usb->dev = ci_hdrc_add_device(&pdev->dev, pdev->resource,
 				      pdev->num_resources, &usb->data);
 	if (IS_ERR(usb->dev)) {
-- 
2.29.2

[PATCH v3 7/9] usb: chipidea: tegra: Specify TX FIFO threshold in UDC SoC info

[Dmitry Osipenko]

The UDC/OTG controller could be switched to a host mode and the
TXFILLTUNING register needs to be programmed properly for the host
mode. Hence specify the TX FIFO threshold in the UDC SoC info.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
---
 drivers/usb/chipidea/ci_hdrc_tegra.c | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/chipidea/ci_hdrc_tegra.c b/drivers/usb/chipidea/ci_hdrc_tegra.c
index 655671159511..90f2a8b786be 100644
--- a/drivers/usb/chipidea/ci_hdrc_tegra.c
+++ b/drivers/usb/chipidea/ci_hdrc_tegra.c
@@ -52,11 +52,20 @@ static const struct tegra_usb_soc_info tegra30_ehci_soc_info = {
 	.txfifothresh = 16,
 };
 
-static const struct tegra_usb_soc_info tegra_udc_soc_info = {
+static const struct tegra_usb_soc_info tegra20_udc_soc_info = {
 	.flags = CI_HDRC_REQUIRES_ALIGNED_DMA |
 		 CI_HDRC_OVERRIDE_PHY_CONTROL |
 		 CI_HDRC_SUPPORTS_RUNTIME_PM,
 	.dr_mode = USB_DR_MODE_UNKNOWN,
+	.txfifothresh = 10,
+};
+
+static const struct tegra_usb_soc_info tegra30_udc_soc_info = {
+	.flags = CI_HDRC_REQUIRES_ALIGNED_DMA |
+		 CI_HDRC_OVERRIDE_PHY_CONTROL |
+		 CI_HDRC_SUPPORTS_RUNTIME_PM,
+	.dr_mode = USB_DR_MODE_UNKNOWN,
+	.txfifothresh = 16,
 };
 
 static const struct of_device_id tegra_usb_of_match[] = {
@@ -68,16 +77,16 @@ static const struct of_device_id tegra_usb_of_match[] = {
 		.data = &tegra30_ehci_soc_info,
 	}, {
 		.compatible = "nvidia,tegra20-udc",
-		.data = &tegra_udc_soc_info,
+		.data = &tegra20_udc_soc_info,
 	}, {
 		.compatible = "nvidia,tegra30-udc",
-		.data = &tegra_udc_soc_info,
+		.data = &tegra30_udc_soc_info,
 	}, {
 		.compatible = "nvidia,tegra114-udc",
-		.data = &tegra_udc_soc_info,
+		.data = &tegra30_udc_soc_info,
 	}, {
 		.compatible = "nvidia,tegra124-udc",
-		.data = &tegra_udc_soc_info,
+		.data = &tegra30_udc_soc_info,
 	}, {
 		/* sentinel */
 	}
-- 
2.29.2

[PATCH v3 8/9] usb: host: ehci-tegra: Remove the driver

[Dmitry Osipenko]

The ChipIdea driver now provides USB2 host mode support for NVIDIA Tegra
SoCs. The ehci-tegra driver is obsolete now, remove it and redirect the
older Kconfig entry to the CI driver.

Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
---
 drivers/usb/host/Kconfig      |  10 +-
 drivers/usb/host/Makefile     |   1 -
 drivers/usb/host/ehci-tegra.c | 604 ----------------------------------
 3 files changed, 7 insertions(+), 608 deletions(-)
 delete mode 100644 drivers/usb/host/ehci-tegra.c

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 31e59309da1f..b94f2a070c05 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -269,10 +269,14 @@ config USB_EHCI_HCD_AT91
 config USB_EHCI_TEGRA
 	tristate "NVIDIA Tegra HCD support"
 	depends on ARCH_TEGRA
-	select USB_EHCI_ROOT_HUB_TT
-	select USB_TEGRA_PHY
+	select USB_CHIPIDEA
+	select USB_CHIPIDEA_HOST
+	select USB_CHIPIDEA_TEGRA
 	help
-	  This driver enables support for the internal USB Host Controllers
+	  This option is deprecated now and the driver was removed, use
+	  USB_CHIPIDEA_TEGRA instead.
+
+	  Enable support for the internal USB Host Controllers
 	  found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.
 
 config USB_EHCI_HCD_PPC_OF
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index c1b08703af10..3e4d298d851f 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -47,7 +47,6 @@ obj-$(CONFIG_USB_EHCI_HCD_SPEAR)	+= ehci-spear.o
 obj-$(CONFIG_USB_EHCI_HCD_STI)	+= ehci-st.o
 obj-$(CONFIG_USB_EHCI_EXYNOS)	+= ehci-exynos.o
 obj-$(CONFIG_USB_EHCI_HCD_AT91) += ehci-atmel.o
-obj-$(CONFIG_USB_EHCI_TEGRA)	+= ehci-tegra.o
 obj-$(CONFIG_USB_EHCI_BRCMSTB)	+= ehci-brcm.o
 
 obj-$(CONFIG_USB_OXU210HP_HCD)	+= oxu210hp-hcd.o
diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c
deleted file mode 100644
index 869d9c4de5fc..000000000000
--- a/drivers/usb/host/ehci-tegra.c
+++ /dev/null
@@ -1,604 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * EHCI-compliant USB host controller driver for NVIDIA Tegra SoCs
- *
- * Copyright (C) 2010 Google, Inc.
- * Copyright (C) 2009 - 2013 NVIDIA Corporation
- */
-
-#include <linux/clk.h>
-#include <linux/dma-mapping.h>
-#include <linux/err.h>
-#include <linux/gpio.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/of_gpio.h>
-#include <linux/platform_device.h>
-#include <linux/pm_runtime.h>
-#include <linux/reset.h>
-#include <linux/slab.h>
-#include <linux/usb/ehci_def.h>
-#include <linux/usb/tegra_usb_phy.h>
-#include <linux/usb.h>
-#include <linux/usb/hcd.h>
-#include <linux/usb/otg.h>
-
-#include "ehci.h"
-
-#define PORT_WAKE_BITS (PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E)
-
-#define TEGRA_USB_DMA_ALIGN 32
-
-#define DRIVER_DESC "Tegra EHCI driver"
-#define DRV_NAME "tegra-ehci"
-
-static struct hc_driver __read_mostly tegra_ehci_hc_driver;
-
-struct tegra_ehci_soc_config {
-	bool has_hostpc;
-};
-
-struct tegra_ehci_hcd {
-	struct clk *clk;
-	struct reset_control *rst;
-	int port_resuming;
-	bool needs_double_reset;
-};
-
-static int tegra_reset_usb_controller(struct platform_device *pdev)
-{
-	struct device_node *phy_np;
-	struct usb_hcd *hcd = platform_get_drvdata(pdev);
-	struct tegra_ehci_hcd *tegra =
-		(struct tegra_ehci_hcd *)hcd_to_ehci(hcd)->priv;
-	struct reset_control *rst;
-	int err;
-
-	phy_np = of_parse_phandle(pdev->dev.of_node, "nvidia,phy", 0);
-	if (!phy_np)
-		return -ENOENT;
-
-	/*
-	 * The 1st USB controller contains some UTMI pad registers that are
-	 * global for all the controllers on the chip. Those registers are
-	 * also cleared when reset is asserted to the 1st controller.
-	 */
-	rst = of_reset_control_get_shared(phy_np, "utmi-pads");
-	if (IS_ERR(rst)) {
-		dev_warn(&pdev->dev,
-			 "can't get utmi-pads reset from the PHY\n");
-		dev_warn(&pdev->dev,
-			 "continuing, but please update your DT\n");
-	} else {
-		/*
-		 * PHY driver performs UTMI-pads reset in a case of
-		 * non-legacy DT.
-		 */
-		reset_control_put(rst);
-	}
-
-	of_node_put(phy_np);
-
-	/* reset control is shared, hence initialize it first */
-	err = reset_control_deassert(tegra->rst);
-	if (err)
-		return err;
-
-	err = reset_control_assert(tegra->rst);
-	if (err)
-		return err;
-
-	udelay(1);
-
-	err = reset_control_deassert(tegra->rst);
-	if (err)
-		return err;
-
-	return 0;
-}
-
-static int tegra_ehci_internal_port_reset(
-	struct ehci_hcd	*ehci,
-	u32 __iomem	*portsc_reg
-)
-{
-	u32		temp;
-	unsigned long	flags;
-	int		retval = 0;
-	int		i, tries;
-	u32		saved_usbintr;
-
-	spin_lock_irqsave(&ehci->lock, flags);
-	saved_usbintr = ehci_readl(ehci, &ehci->regs->intr_enable);
-	/* disable USB interrupt */
-	ehci_writel(ehci, 0, &ehci->regs->intr_enable);
-	spin_unlock_irqrestore(&ehci->lock, flags);
-
-	/*
-	 * Here we have to do Port Reset at most twice for
-	 * Port Enable bit to be set.
-	 */
-	for (i = 0; i < 2; i++) {
-		temp = ehci_readl(ehci, portsc_reg);
-		temp |= PORT_RESET;
-		ehci_writel(ehci, temp, portsc_reg);
-		mdelay(10);
-		temp &= ~PORT_RESET;
-		ehci_writel(ehci, temp, portsc_reg);
-		mdelay(1);
-		tries = 100;
-		do {
-			mdelay(1);
-			/*
-			 * Up to this point, Port Enable bit is
-			 * expected to be set after 2 ms waiting.
-			 * USB1 usually takes extra 45 ms, for safety,
-			 * we take 100 ms as timeout.
-			 */
-			temp = ehci_readl(ehci, portsc_reg);
-		} while (!(temp & PORT_PE) && tries--);
-		if (temp & PORT_PE)
-			break;
-	}
-	if (i == 2)
-		retval = -ETIMEDOUT;
-
-	/*
-	 * Clear Connect Status Change bit if it's set.
-	 * We can't clear PORT_PEC. It will also cause PORT_PE to be cleared.
-	 */
-	if (temp & PORT_CSC)
-		ehci_writel(ehci, PORT_CSC, portsc_reg);
-
-	/*
-	 * Write to clear any interrupt status bits that might be set
-	 * during port reset.
-	 */
-	temp = ehci_readl(ehci, &ehci->regs->status);
-	ehci_writel(ehci, temp, &ehci->regs->status);
-
-	/* restore original interrupt enable bits */
-	ehci_writel(ehci, saved_usbintr, &ehci->regs->intr_enable);
-	return retval;
-}
-
-static int tegra_ehci_hub_control(
-	struct usb_hcd	*hcd,
-	u16		typeReq,
-	u16		wValue,
-	u16		wIndex,
-	char		*buf,
-	u16		wLength
-)
-{
-	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
-	struct tegra_ehci_hcd *tegra = (struct tegra_ehci_hcd *)ehci->priv;
-	u32 __iomem	*status_reg;
-	u32		temp;
-	unsigned long	flags;
-	int		retval = 0;
-
-	status_reg = &ehci->regs->port_status[(wIndex & 0xff) - 1];
-
-	spin_lock_irqsave(&ehci->lock, flags);
-
-	if (typeReq == GetPortStatus) {
-		temp = ehci_readl(ehci, status_reg);
-		if (tegra->port_resuming && !(temp & PORT_SUSPEND)) {
-			/* Resume completed, re-enable disconnect detection */
-			tegra->port_resuming = 0;
-			tegra_usb_phy_postresume(hcd->usb_phy);
-		}
-	}
-
-	else if (typeReq == SetPortFeature && wValue == USB_PORT_FEAT_SUSPEND) {
-		temp = ehci_readl(ehci, status_reg);
-		if ((temp & PORT_PE) == 0 || (temp & PORT_RESET) != 0) {
-			retval = -EPIPE;
-			goto done;
-		}
-
-		temp &= ~(PORT_RWC_BITS | PORT_WKCONN_E);
-		temp |= PORT_WKDISC_E | PORT_WKOC_E;
-		ehci_writel(ehci, temp | PORT_SUSPEND, status_reg);
-
-		/*
-		 * If a transaction is in progress, there may be a delay in
-		 * suspending the port. Poll until the port is suspended.
-		 */
-		if (ehci_handshake(ehci, status_reg, PORT_SUSPEND,
-						PORT_SUSPEND, 5000))
-			pr_err("%s: timeout waiting for SUSPEND\n", __func__);
-
-		set_bit((wIndex & 0xff) - 1, &ehci->suspended_ports);
-		goto done;
-	}
-
-	/* For USB1 port we need to issue Port Reset twice internally */
-	if (tegra->needs_double_reset &&
-	   (typeReq == SetPortFeature && wValue == USB_PORT_FEAT_RESET)) {
-		spin_unlock_irqrestore(&ehci->lock, flags);
-		return tegra_ehci_internal_port_reset(ehci, status_reg);
-	}
-
-	/*
-	 * Tegra host controller will time the resume operation to clear the bit
-	 * when the port control state switches to HS or FS Idle. This behavior
-	 * is different from EHCI where the host controller driver is required
-	 * to set this bit to a zero after the resume duration is timed in the
-	 * driver.
-	 */
-	else if (typeReq == ClearPortFeature &&
-					wValue == USB_PORT_FEAT_SUSPEND) {
-		temp = ehci_readl(ehci, status_reg);
-		if ((temp & PORT_RESET) || !(temp & PORT_PE)) {
-			retval = -EPIPE;
-			goto done;
-		}
-
-		if (!(temp & PORT_SUSPEND))
-			goto done;
-
-		/* Disable disconnect detection during port resume */
-		tegra_usb_phy_preresume(hcd->usb_phy);
-
-		ehci->reset_done[wIndex-1] = jiffies + msecs_to_jiffies(25);
-
-		temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
-		/* start resume signalling */
-		ehci_writel(ehci, temp | PORT_RESUME, status_reg);
-		set_bit(wIndex-1, &ehci->resuming_ports);
-
-		spin_unlock_irqrestore(&ehci->lock, flags);
-		msleep(20);
-		spin_lock_irqsave(&ehci->lock, flags);
-
-		/* Poll until the controller clears RESUME and SUSPEND */
-		if (ehci_handshake(ehci, status_reg, PORT_RESUME, 0, 2000))
-			pr_err("%s: timeout waiting for RESUME\n", __func__);
-		if (ehci_handshake(ehci, status_reg, PORT_SUSPEND, 0, 2000))
-			pr_err("%s: timeout waiting for SUSPEND\n", __func__);
-
-		ehci->reset_done[wIndex-1] = 0;
-		clear_bit(wIndex-1, &ehci->resuming_ports);
-
-		tegra->port_resuming = 1;
-		goto done;
-	}
-
-	spin_unlock_irqrestore(&ehci->lock, flags);
-
-	/* Handle the hub control events here */
-	return ehci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength);
-
-done:
-	spin_unlock_irqrestore(&ehci->lock, flags);
-	return retval;
-}
-
-struct dma_aligned_buffer {
-	void *kmalloc_ptr;
-	void *old_xfer_buffer;
-	u8 data[];
-};
-
-static void free_dma_aligned_buffer(struct urb *urb)
-{
-	struct dma_aligned_buffer *temp;
-	size_t length;
-
-	if (!(urb->transfer_flags & URB_ALIGNED_TEMP_BUFFER))
-		return;
-
-	temp = container_of(urb->transfer_buffer,
-		struct dma_aligned_buffer, data);
-
-	if (usb_urb_dir_in(urb)) {
-		if (usb_pipeisoc(urb->pipe))
-			length = urb->transfer_buffer_length;
-		else
-			length = urb->actual_length;
-
-		memcpy(temp->old_xfer_buffer, temp->data, length);
-	}
-	urb->transfer_buffer = temp->old_xfer_buffer;
-	kfree(temp->kmalloc_ptr);
-
-	urb->transfer_flags &= ~URB_ALIGNED_TEMP_BUFFER;
-}
-
-static int alloc_dma_aligned_buffer(struct urb *urb, gfp_t mem_flags)
-{
-	struct dma_aligned_buffer *temp, *kmalloc_ptr;
-	size_t kmalloc_size;
-
-	if (urb->num_sgs || urb->sg ||
-	    urb->transfer_buffer_length == 0 ||
-	    !((uintptr_t)urb->transfer_buffer & (TEGRA_USB_DMA_ALIGN - 1)))
-		return 0;
-
-	/* Allocate a buffer with enough padding for alignment */
-	kmalloc_size = urb->transfer_buffer_length +
-		sizeof(struct dma_aligned_buffer) + TEGRA_USB_DMA_ALIGN - 1;
-
-	kmalloc_ptr = kmalloc(kmalloc_size, mem_flags);
-	if (!kmalloc_ptr)
-		return -ENOMEM;
-
-	/* Position our struct dma_aligned_buffer such that data is aligned */
-	temp = PTR_ALIGN(kmalloc_ptr + 1, TEGRA_USB_DMA_ALIGN) - 1;
-	temp->kmalloc_ptr = kmalloc_ptr;
-	temp->old_xfer_buffer = urb->transfer_buffer;
-	if (usb_urb_dir_out(urb))
-		memcpy(temp->data, urb->transfer_buffer,
-		       urb->transfer_buffer_length);
-	urb->transfer_buffer = temp->data;
-
-	urb->transfer_flags |= URB_ALIGNED_TEMP_BUFFER;
-
-	return 0;
-}
-
-static int tegra_ehci_map_urb_for_dma(struct usb_hcd *hcd, struct urb *urb,
-				      gfp_t mem_flags)
-{
-	int ret;
-
-	ret = alloc_dma_aligned_buffer(urb, mem_flags);
-	if (ret)
-		return ret;
-
-	ret = usb_hcd_map_urb_for_dma(hcd, urb, mem_flags);
-	if (ret)
-		free_dma_aligned_buffer(urb);
-
-	return ret;
-}
-
-static void tegra_ehci_unmap_urb_for_dma(struct usb_hcd *hcd, struct urb *urb)
-{
-	usb_hcd_unmap_urb_for_dma(hcd, urb);
-	free_dma_aligned_buffer(urb);
-}
-
-static const struct tegra_ehci_soc_config tegra30_soc_config = {
-	.has_hostpc = true,
-};
-
-static const struct tegra_ehci_soc_config tegra20_soc_config = {
-	.has_hostpc = false,
-};
-
-static const struct of_device_id tegra_ehci_of_match[] = {
-	{ .compatible = "nvidia,tegra30-ehci", .data = &tegra30_soc_config },
-	{ .compatible = "nvidia,tegra20-ehci", .data = &tegra20_soc_config },
-	{ },
-};
-
-static int tegra_ehci_probe(struct platform_device *pdev)
-{
-	const struct of_device_id *match;
-	const struct tegra_ehci_soc_config *soc_config;
-	struct resource *res;
-	struct usb_hcd *hcd;
-	struct ehci_hcd *ehci;
-	struct tegra_ehci_hcd *tegra;
-	int err = 0;
-	int irq;
-	struct usb_phy *u_phy;
-
-	match = of_match_device(tegra_ehci_of_match, &pdev->dev);
-	if (!match) {
-		dev_err(&pdev->dev, "Error: No device match found\n");
-		return -ENODEV;
-	}
-	soc_config = match->data;
-
-	/* Right now device-tree probed devices don't get dma_mask set.
-	 * Since shared usb code relies on it, set it here for now.
-	 * Once we have dma capability bindings this can go away.
-	 */
-	err = dma_coerce_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
-	if (err)
-		return err;
-
-	hcd = usb_create_hcd(&tegra_ehci_hc_driver, &pdev->dev,
-					dev_name(&pdev->dev));
-	if (!hcd) {
-		dev_err(&pdev->dev, "Unable to create HCD\n");
-		return -ENOMEM;
-	}
-	platform_set_drvdata(pdev, hcd);
-	ehci = hcd_to_ehci(hcd);
-	tegra = (struct tegra_ehci_hcd *)ehci->priv;
-
-	hcd->has_tt = 1;
-
-	tegra->clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(tegra->clk)) {
-		dev_err(&pdev->dev, "Can't get ehci clock\n");
-		err = PTR_ERR(tegra->clk);
-		goto cleanup_hcd_create;
-	}
-
-	tegra->rst = devm_reset_control_get_shared(&pdev->dev, "usb");
-	if (IS_ERR(tegra->rst)) {
-		dev_err(&pdev->dev, "Can't get ehci reset\n");
-		err = PTR_ERR(tegra->rst);
-		goto cleanup_hcd_create;
-	}
-
-	err = clk_prepare_enable(tegra->clk);
-	if (err)
-		goto cleanup_hcd_create;
-
-	err = tegra_reset_usb_controller(pdev);
-	if (err) {
-		dev_err(&pdev->dev, "Failed to reset controller\n");
-		goto cleanup_clk_en;
-	}
-
-	u_phy = devm_usb_get_phy_by_phandle(&pdev->dev, "nvidia,phy", 0);
-	if (IS_ERR(u_phy)) {
-		err = -EPROBE_DEFER;
-		goto cleanup_clk_en;
-	}
-	hcd->usb_phy = u_phy;
-	hcd->skip_phy_initialization = 1;
-
-	tegra->needs_double_reset = of_property_read_bool(pdev->dev.of_node,
-		"nvidia,needs-double-reset");
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	hcd->regs = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(hcd->regs)) {
-		err = PTR_ERR(hcd->regs);
-		goto cleanup_clk_en;
-	}
-	hcd->rsrc_start = res->start;
-	hcd->rsrc_len = resource_size(res);
-
-	ehci->caps = hcd->regs + 0x100;
-	ehci->has_hostpc = soc_config->has_hostpc;
-
-	err = usb_phy_init(hcd->usb_phy);
-	if (err) {
-		dev_err(&pdev->dev, "Failed to initialize phy\n");
-		goto cleanup_clk_en;
-	}
-
-	u_phy->otg = devm_kzalloc(&pdev->dev, sizeof(struct usb_otg),
-			     GFP_KERNEL);
-	if (!u_phy->otg) {
-		err = -ENOMEM;
-		goto cleanup_phy;
-	}
-	u_phy->otg->host = hcd_to_bus(hcd);
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq < 0) {
-		err = irq;
-		goto cleanup_phy;
-	}
-
-	otg_set_host(u_phy->otg, &hcd->self);
-
-	err = usb_add_hcd(hcd, irq, IRQF_SHARED);
-	if (err) {
-		dev_err(&pdev->dev, "Failed to add USB HCD\n");
-		goto cleanup_otg_set_host;
-	}
-	device_wakeup_enable(hcd->self.controller);
-
-	return err;
-
-cleanup_otg_set_host:
-	otg_set_host(u_phy->otg, NULL);
-cleanup_phy:
-	usb_phy_shutdown(hcd->usb_phy);
-cleanup_clk_en:
-	clk_disable_unprepare(tegra->clk);
-cleanup_hcd_create:
-	usb_put_hcd(hcd);
-	return err;
-}
-
-static int tegra_ehci_remove(struct platform_device *pdev)
-{
-	struct usb_hcd *hcd = platform_get_drvdata(pdev);
-	struct tegra_ehci_hcd *tegra =
-		(struct tegra_ehci_hcd *)hcd_to_ehci(hcd)->priv;
-
-	usb_remove_hcd(hcd);
-	otg_set_host(hcd->usb_phy->otg, NULL);
-	usb_phy_shutdown(hcd->usb_phy);
-	clk_disable_unprepare(tegra->clk);
-	usb_put_hcd(hcd);
-
-	return 0;
-}
-
-static void tegra_ehci_hcd_shutdown(struct platform_device *pdev)
-{
-	struct usb_hcd *hcd = platform_get_drvdata(pdev);
-
-	if (hcd->driver->shutdown)
-		hcd->driver->shutdown(hcd);
-}
-
-static struct platform_driver tegra_ehci_driver = {
-	.probe		= tegra_ehci_probe,
-	.remove		= tegra_ehci_remove,
-	.shutdown	= tegra_ehci_hcd_shutdown,
-	.driver		= {
-		.name	= DRV_NAME,
-		.of_match_table = tegra_ehci_of_match,
-	}
-};
-
-static int tegra_ehci_reset(struct usb_hcd *hcd)
-{
-	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
-	int retval;
-	int txfifothresh;
-
-	retval = ehci_setup(hcd);
-	if (retval)
-		return retval;
-
-	/*
-	 * We should really pull this value out of tegra_ehci_soc_config, but
-	 * to avoid needing access to it, make use of the fact that Tegra20 is
-	 * the only one so far that needs a value of 10, and Tegra20 is the
-	 * only one which doesn't set has_hostpc.
-	 */
-	txfifothresh = ehci->has_hostpc ? 0x10 : 10;
-	ehci_writel(ehci, txfifothresh << 16, &ehci->regs->txfill_tuning);
-
-	return 0;
-}
-
-static const struct ehci_driver_overrides tegra_overrides __initconst = {
-	.extra_priv_size	= sizeof(struct tegra_ehci_hcd),
-	.reset			= tegra_ehci_reset,
-};
-
-static int __init ehci_tegra_init(void)
-{
-	if (usb_disabled())
-		return -ENODEV;
-
-	pr_info(DRV_NAME ": " DRIVER_DESC "\n");
-
-	ehci_init_driver(&tegra_ehci_hc_driver, &tegra_overrides);
-
-	/*
-	 * The Tegra HW has some unusual quirks, which require Tegra-specific
-	 * workarounds. We override certain hc_driver functions here to
-	 * achieve that. We explicitly do not enhance ehci_driver_overrides to
-	 * allow this more easily, since this is an unusual case, and we don't
-	 * want to encourage others to override these functions by making it
-	 * too easy.
-	 */
-
-	tegra_ehci_hc_driver.map_urb_for_dma = tegra_ehci_map_urb_for_dma;
-	tegra_ehci_hc_driver.unmap_urb_for_dma = tegra_ehci_unmap_urb_for_dma;
-	tegra_ehci_hc_driver.hub_control = tegra_ehci_hub_control;
-
-	return platform_driver_register(&tegra_ehci_driver);
-}
-module_init(ehci_tegra_init);
-
-static void __exit ehci_tegra_cleanup(void)
-{
-	platform_driver_unregister(&tegra_ehci_driver);
-}
-module_exit(ehci_tegra_cleanup);
-
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:" DRV_NAME);
-MODULE_DEVICE_TABLE(of, tegra_ehci_of_match);
-- 
2.29.2

[PATCH v3 9/9] ARM: tegra_defconfig: Enable USB_CHIPIDEA_HOST and remove USB_EHCI_TEGRA

[Dmitry Osipenko]

The ehci-tegra driver was superseded by the generic ChipIdea USB driver,
update the tegra's defconfig accordingly.

Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
---
 arch/arm/configs/tegra_defconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/configs/tegra_defconfig b/arch/arm/configs/tegra_defconfig
index 74739a52a8ad..ae0709265493 100644
--- a/arch/arm/configs/tegra_defconfig
+++ b/arch/arm/configs/tegra_defconfig
@@ -237,12 +237,13 @@ CONFIG_USB=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_TEGRA=y
 CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_EHCI_TEGRA=y
 CONFIG_USB_ACM=y
 CONFIG_USB_WDM=y
 CONFIG_USB_STORAGE=y
 CONFIG_USB_CHIPIDEA=y
 CONFIG_USB_CHIPIDEA_UDC=y
+CONFIG_USB_CHIPIDEA_HOST=y
+CONFIG_USB_CHIPIDEA_TEGRA=y
 CONFIG_USB_GADGET=y
 CONFIG_MMC=y
 CONFIG_MMC_BLOCK_MINORS=16
-- 
2.29.2

Re: [PATCH v3 0/9] Support Runtime PM and host mode by Tegra ChipIdea USB driver

[Peter Chen]

On 20-12-18 15:02:37, Dmitry Osipenko wrote:
> This series implements Runtime PM support for the Tegra ChipIdea USB driver.
> It also squashes the older ehci-tegra driver into the ChipIdea driver, hence
> the RPM is supported by both UDC and host controllers, secondly this opens
> opportunity for implementing OTG support in the future.
> 
> Patchset was tested on various Tegra20, Tegra30 and Tegra124 devices.
> Thanks to Peter Geis, Matt Merhar, Nicolas Chauvet and Ion Agorria for
> helping with the extensive and productive testing!
> 
> Changelog:
> 
> v3: - Replaced "goto" with if-statements as was suggested by Thierry Reding.
> 
>     - Improved wording of the deprecated Kconfig entry as was suggested
>       by Alan Stern.
> 
>     - Added ACKs from Thierry Reding and Alan Stern.
> 
>     - Added a new minor patch "Specify TX FIFO threshold in UDC SoC info"
>       just for completeness, since we can now switch OTG to host mode in
>       the ChipIdea driver. Although, OTG support remains a work-in-progress
>       for now.
> 
> v2: - Improved comments in the code as it was suggested by Peter Chen and
>       Sergei Shtylyov for v1.
> 
>     - Replaced mdelay() with fsleep() and made ci->hdc to reset to NULL in
>       a error code path, like it was suggested by Peter Chen.
> 
>     - Redirected deprecated USB_EHCI_TEGRA Kconfig entry to USB_CHIPIDEA_TEGRA
>       as was suggested by Alan Stern.
> 
>     - Improved commit message and added ACK from Thierry Reding to the patch
>       that removes MODULE_ALIAS.
> 
>     - Fixed UDC PHY waking up on ASUS TF201 tablet device by utilizing
>       additional VBUS sensor. This was reported and tested by Ion Agorria.
> 
>     - Added t-b from Ion Agorria.
> 
> Dmitry Osipenko (8):
>   usb: phy: tegra: Add delay after power up
>   usb: phy: tegra: Support waking up from a low power mode
>   usb: chipidea: tegra: Remove MODULE_ALIAS
>   usb: chipidea: tegra: Rename UDC to USB
>   usb: chipidea: tegra: Support runtime PM
>   usb: chipidea: tegra: Specify TX FIFO threshold in UDC SoC info
>   usb: host: ehci-tegra: Remove the driver
>   ARM: tegra_defconfig: Enable USB_CHIPIDEA_HOST and remove
>     USB_EHCI_TEGRA
> 
> Peter Geis (1):
>   usb: chipidea: tegra: Support host mode

Chipidea related (patch 3-7) are applied, thanks.

Peter
> 
>  arch/arm/configs/tegra_defconfig     |   3 +-
>  drivers/usb/chipidea/Kconfig         |   3 +-
>  drivers/usb/chipidea/ci_hdrc_tegra.c | 344 ++++++++++++---
>  drivers/usb/chipidea/core.c          |  10 +-
>  drivers/usb/chipidea/host.c          | 104 ++++-
>  drivers/usb/host/Kconfig             |  10 +-
>  drivers/usb/host/Makefile            |   1 -
>  drivers/usb/host/ehci-tegra.c        | 604 ---------------------------
>  drivers/usb/phy/phy-tegra-usb.c      | 103 ++++-
>  include/linux/usb/chipidea.h         |   6 +
>  include/linux/usb/tegra_usb_phy.h    |   2 +
>  11 files changed, 518 insertions(+), 672 deletions(-)
>  delete mode 100644 drivers/usb/host/ehci-tegra.c
> 
> -- 
> 2.29.2
> 

-- 

Thanks,
Peter Chen

Re: [PATCH v3 0/9] Support Runtime PM and host mode by Tegra ChipIdea USB driver

[Dmitry Osipenko]

29.12.2020 08:16, Peter Chen пишет:
> On 20-12-18 15:02:37, Dmitry Osipenko wrote:
>> This series implements Runtime PM support for the Tegra ChipIdea USB driver.
>> It also squashes the older ehci-tegra driver into the ChipIdea driver, hence
>> the RPM is supported by both UDC and host controllers, secondly this opens
>> opportunity for implementing OTG support in the future.
>>
>> Patchset was tested on various Tegra20, Tegra30 and Tegra124 devices.
>> Thanks to Peter Geis, Matt Merhar, Nicolas Chauvet and Ion Agorria for
>> helping with the extensive and productive testing!
>>
>> Changelog:
>>
>> v3: - Replaced "goto" with if-statements as was suggested by Thierry Reding.
>>
>>     - Improved wording of the deprecated Kconfig entry as was suggested
>>       by Alan Stern.
>>
>>     - Added ACKs from Thierry Reding and Alan Stern.
>>
>>     - Added a new minor patch "Specify TX FIFO threshold in UDC SoC info"
>>       just for completeness, since we can now switch OTG to host mode in
>>       the ChipIdea driver. Although, OTG support remains a work-in-progress
>>       for now.
>>
>> v2: - Improved comments in the code as it was suggested by Peter Chen and
>>       Sergei Shtylyov for v1.
>>
>>     - Replaced mdelay() with fsleep() and made ci->hdc to reset to NULL in
>>       a error code path, like it was suggested by Peter Chen.
>>
>>     - Redirected deprecated USB_EHCI_TEGRA Kconfig entry to USB_CHIPIDEA_TEGRA
>>       as was suggested by Alan Stern.
>>
>>     - Improved commit message and added ACK from Thierry Reding to the patch
>>       that removes MODULE_ALIAS.
>>
>>     - Fixed UDC PHY waking up on ASUS TF201 tablet device by utilizing
>>       additional VBUS sensor. This was reported and tested by Ion Agorria.
>>
>>     - Added t-b from Ion Agorria.
>>
>> Dmitry Osipenko (8):
>>   usb: phy: tegra: Add delay after power up
>>   usb: phy: tegra: Support waking up from a low power mode
>>   usb: chipidea: tegra: Remove MODULE_ALIAS
>>   usb: chipidea: tegra: Rename UDC to USB
>>   usb: chipidea: tegra: Support runtime PM
>>   usb: chipidea: tegra: Specify TX FIFO threshold in UDC SoC info
>>   usb: host: ehci-tegra: Remove the driver
>>   ARM: tegra_defconfig: Enable USB_CHIPIDEA_HOST and remove
>>     USB_EHCI_TEGRA
>>
>> Peter Geis (1):
>>   usb: chipidea: tegra: Support host mode
> 
> Chipidea related (patch 3-7) are applied, thanks.

Hello Peter,

Thank you for applying the patches.

Who will apply the remaining patches?

The Chipidea patch #6 depends on the PHY changes, otherwise USB will
suspend and never resume.

Re: [PATCH v3 0/9] Support Runtime PM and host mode by Tegra ChipIdea USB driver

[Dmitry Osipenko]

29.12.2020 17:26, Dmitry Osipenko пишет:
> 29.12.2020 08:16, Peter Chen пишет:
>> On 20-12-18 15:02:37, Dmitry Osipenko wrote:
>>> This series implements Runtime PM support for the Tegra ChipIdea USB driver.
>>> It also squashes the older ehci-tegra driver into the ChipIdea driver, hence
>>> the RPM is supported by both UDC and host controllers, secondly this opens
>>> opportunity for implementing OTG support in the future.
>>>
>>> Patchset was tested on various Tegra20, Tegra30 and Tegra124 devices.
>>> Thanks to Peter Geis, Matt Merhar, Nicolas Chauvet and Ion Agorria for
>>> helping with the extensive and productive testing!
>>>
>>> Changelog:
>>>
>>> v3: - Replaced "goto" with if-statements as was suggested by Thierry Reding.
>>>
>>>     - Improved wording of the deprecated Kconfig entry as was suggested
>>>       by Alan Stern.
>>>
>>>     - Added ACKs from Thierry Reding and Alan Stern.
>>>
>>>     - Added a new minor patch "Specify TX FIFO threshold in UDC SoC info"
>>>       just for completeness, since we can now switch OTG to host mode in
>>>       the ChipIdea driver. Although, OTG support remains a work-in-progress
>>>       for now.
>>>
>>> v2: - Improved comments in the code as it was suggested by Peter Chen and
>>>       Sergei Shtylyov for v1.
>>>
>>>     - Replaced mdelay() with fsleep() and made ci->hdc to reset to NULL in
>>>       a error code path, like it was suggested by Peter Chen.
>>>
>>>     - Redirected deprecated USB_EHCI_TEGRA Kconfig entry to USB_CHIPIDEA_TEGRA
>>>       as was suggested by Alan Stern.
>>>
>>>     - Improved commit message and added ACK from Thierry Reding to the patch
>>>       that removes MODULE_ALIAS.
>>>
>>>     - Fixed UDC PHY waking up on ASUS TF201 tablet device by utilizing
>>>       additional VBUS sensor. This was reported and tested by Ion Agorria.
>>>
>>>     - Added t-b from Ion Agorria.
>>>
>>> Dmitry Osipenko (8):
>>>   usb: phy: tegra: Add delay after power up
>>>   usb: phy: tegra: Support waking up from a low power mode
>>>   usb: chipidea: tegra: Remove MODULE_ALIAS
>>>   usb: chipidea: tegra: Rename UDC to USB
>>>   usb: chipidea: tegra: Support runtime PM
>>>   usb: chipidea: tegra: Specify TX FIFO threshold in UDC SoC info
>>>   usb: host: ehci-tegra: Remove the driver
>>>   ARM: tegra_defconfig: Enable USB_CHIPIDEA_HOST and remove
>>>     USB_EHCI_TEGRA
>>>
>>> Peter Geis (1):
>>>   usb: chipidea: tegra: Support host mode
>>
>> Chipidea related (patch 3-7) are applied, thanks.
> 
> Hello Peter,
> 
> Thank you for applying the patches.
> 
> Who will apply the remaining patches?
> 
> The Chipidea patch #6 depends on the PHY changes, otherwise USB will
> suspend and never resume.
> 

Peter, could you please apply the PHY and defconfig patches along with
the CI patches to -next? I.e. the whole series. Preferentially in
original ordering of patches should be preserved.

Thanks in advance.

Re: [PATCH v3 0/9] Support Runtime PM and host mode by Tegra ChipIdea USB driver

[Peter Chen]

On 21-01-12 09:56:37, Dmitry Osipenko wrote:
> 29.12.2020 17:26, Dmitry Osipenko пишет:
> > 29.12.2020 08:16, Peter Chen пишет:
> >> On 20-12-18 15:02:37, Dmitry Osipenko wrote:
> >>> This series implements Runtime PM support for the Tegra ChipIdea USB driver.
> >>> It also squashes the older ehci-tegra driver into the ChipIdea driver, hence
> >>> the RPM is supported by both UDC and host controllers, secondly this opens
> >>> opportunity for implementing OTG support in the future.
> >>>
> >>> Patchset was tested on various Tegra20, Tegra30 and Tegra124 devices.
> >>> Thanks to Peter Geis, Matt Merhar, Nicolas Chauvet and Ion Agorria for
> >>> helping with the extensive and productive testing!
> >>>
> >>> Changelog:
> >>>
> >>> v3: - Replaced "goto" with if-statements as was suggested by Thierry Reding.
> >>>
> >>>     - Improved wording of the deprecated Kconfig entry as was suggested
> >>>       by Alan Stern.
> >>>
> >>>     - Added ACKs from Thierry Reding and Alan Stern.
> >>>
> >>>     - Added a new minor patch "Specify TX FIFO threshold in UDC SoC info"
> >>>       just for completeness, since we can now switch OTG to host mode in
> >>>       the ChipIdea driver. Although, OTG support remains a work-in-progress
> >>>       for now.
> >>>
> >>> v2: - Improved comments in the code as it was suggested by Peter Chen and
> >>>       Sergei Shtylyov for v1.
> >>>
> >>>     - Replaced mdelay() with fsleep() and made ci->hdc to reset to NULL in
> >>>       a error code path, like it was suggested by Peter Chen.
> >>>
> >>>     - Redirected deprecated USB_EHCI_TEGRA Kconfig entry to USB_CHIPIDEA_TEGRA
> >>>       as was suggested by Alan Stern.
> >>>
> >>>     - Improved commit message and added ACK from Thierry Reding to the patch
> >>>       that removes MODULE_ALIAS.
> >>>
> >>>     - Fixed UDC PHY waking up on ASUS TF201 tablet device by utilizing
> >>>       additional VBUS sensor. This was reported and tested by Ion Agorria.
> >>>
> >>>     - Added t-b from Ion Agorria.
> >>>
> >>> Dmitry Osipenko (8):
> >>>   usb: phy: tegra: Add delay after power up
> >>>   usb: phy: tegra: Support waking up from a low power mode
> >>>   usb: chipidea: tegra: Remove MODULE_ALIAS
> >>>   usb: chipidea: tegra: Rename UDC to USB
> >>>   usb: chipidea: tegra: Support runtime PM
> >>>   usb: chipidea: tegra: Specify TX FIFO threshold in UDC SoC info
> >>>   usb: host: ehci-tegra: Remove the driver
> >>>   ARM: tegra_defconfig: Enable USB_CHIPIDEA_HOST and remove
> >>>     USB_EHCI_TEGRA
> >>>
> >>> Peter Geis (1):
> >>>   usb: chipidea: tegra: Support host mode
> >>
> >> Chipidea related (patch 3-7) are applied, thanks.
> > 
> > Hello Peter,
> > 
> > Thank you for applying the patches.
> > 
> > Who will apply the remaining patches?
> > 
> > The Chipidea patch #6 depends on the PHY changes, otherwise USB will
> > suspend and never resume.
> > 
> 
> Peter, could you please apply the PHY and defconfig patches along with
> the CI patches to -next? I.e. the whole series. Preferentially in
> original ordering of patches should be preserved.
> 

Hi Dmitry,

Usually, Greg could apply all USB patches, if I apply other USB related
patches, it may cause conflict with other patches in other's tree.
Greg, free feel to apply this series with 
Acked-by: Peter Chen <peter.chen@kernel.org>
for chipidea part.

For ARM defconfig patch, I think it should go ARM's tree.

-- 

Thanks,
Peter Chen

Re: [PATCH v3 0/9] Support Runtime PM and host mode by Tegra ChipIdea USB driver

[Dmitry Osipenko]

13.01.2021 04:20, Peter Chen пишет:
> On 21-01-12 09:56:37, Dmitry Osipenko wrote:
>> 29.12.2020 17:26, Dmitry Osipenko пишет:
>>> 29.12.2020 08:16, Peter Chen пишет:
>>>> On 20-12-18 15:02:37, Dmitry Osipenko wrote:
>>>>> This series implements Runtime PM support for the Tegra ChipIdea USB driver.
>>>>> It also squashes the older ehci-tegra driver into the ChipIdea driver, hence
>>>>> the RPM is supported by both UDC and host controllers, secondly this opens
>>>>> opportunity for implementing OTG support in the future.
>>>>>
>>>>> Patchset was tested on various Tegra20, Tegra30 and Tegra124 devices.
>>>>> Thanks to Peter Geis, Matt Merhar, Nicolas Chauvet and Ion Agorria for
>>>>> helping with the extensive and productive testing!
>>>>>
>>>>> Changelog:
>>>>>
>>>>> v3: - Replaced "goto" with if-statements as was suggested by Thierry Reding.
>>>>>
>>>>>     - Improved wording of the deprecated Kconfig entry as was suggested
>>>>>       by Alan Stern.
>>>>>
>>>>>     - Added ACKs from Thierry Reding and Alan Stern.
>>>>>
>>>>>     - Added a new minor patch "Specify TX FIFO threshold in UDC SoC info"
>>>>>       just for completeness, since we can now switch OTG to host mode in
>>>>>       the ChipIdea driver. Although, OTG support remains a work-in-progress
>>>>>       for now.
>>>>>
>>>>> v2: - Improved comments in the code as it was suggested by Peter Chen and
>>>>>       Sergei Shtylyov for v1.
>>>>>
>>>>>     - Replaced mdelay() with fsleep() and made ci->hdc to reset to NULL in
>>>>>       a error code path, like it was suggested by Peter Chen.
>>>>>
>>>>>     - Redirected deprecated USB_EHCI_TEGRA Kconfig entry to USB_CHIPIDEA_TEGRA
>>>>>       as was suggested by Alan Stern.
>>>>>
>>>>>     - Improved commit message and added ACK from Thierry Reding to the patch
>>>>>       that removes MODULE_ALIAS.
>>>>>
>>>>>     - Fixed UDC PHY waking up on ASUS TF201 tablet device by utilizing
>>>>>       additional VBUS sensor. This was reported and tested by Ion Agorria.
>>>>>
>>>>>     - Added t-b from Ion Agorria.
>>>>>
>>>>> Dmitry Osipenko (8):
>>>>>   usb: phy: tegra: Add delay after power up
>>>>>   usb: phy: tegra: Support waking up from a low power mode
>>>>>   usb: chipidea: tegra: Remove MODULE_ALIAS
>>>>>   usb: chipidea: tegra: Rename UDC to USB
>>>>>   usb: chipidea: tegra: Support runtime PM
>>>>>   usb: chipidea: tegra: Specify TX FIFO threshold in UDC SoC info
>>>>>   usb: host: ehci-tegra: Remove the driver
>>>>>   ARM: tegra_defconfig: Enable USB_CHIPIDEA_HOST and remove
>>>>>     USB_EHCI_TEGRA
>>>>>
>>>>> Peter Geis (1):
>>>>>   usb: chipidea: tegra: Support host mode
>>>>
>>>> Chipidea related (patch 3-7) are applied, thanks.
>>>
>>> Hello Peter,
>>>
>>> Thank you for applying the patches.
>>>
>>> Who will apply the remaining patches?
>>>
>>> The Chipidea patch #6 depends on the PHY changes, otherwise USB will
>>> suspend and never resume.
>>>
>>
>> Peter, could you please apply the PHY and defconfig patches along with
>> the CI patches to -next? I.e. the whole series. Preferentially in
>> original ordering of patches should be preserved.
>>
> 
> Hi Dmitry,
> 
> Usually, Greg could apply all USB patches, if I apply other USB related
> patches, it may cause conflict with other patches in other's tree.
> Greg, free feel to apply this series with 
> Acked-by: Peter Chen <peter.chen@kernel.org>
> for chipidea part.
> 
> For ARM defconfig patch, I think it should go ARM's tree.
> 

Thank you for the answer!

It's not the ARM defconfig, but a local tegra_defconfig. It should be
fine to take the patch via the USB tree since Thierry already acked it
and asked to do so.

Greg, please take this whole series. Thanks in advance!

Re: [PATCH v3 0/9] Support Runtime PM and host mode by Tegra ChipIdea USB driver

[Greg Kroah-Hartman]

On Wed, Jan 13, 2021 at 12:01:51PM +0300, Dmitry Osipenko wrote:
> 13.01.2021 04:20, Peter Chen пишет:
> > On 21-01-12 09:56:37, Dmitry Osipenko wrote:
> >> 29.12.2020 17:26, Dmitry Osipenko пишет:
> >>> 29.12.2020 08:16, Peter Chen пишет:
> >>>> On 20-12-18 15:02:37, Dmitry Osipenko wrote:
> >>>>> This series implements Runtime PM support for the Tegra ChipIdea USB driver.
> >>>>> It also squashes the older ehci-tegra driver into the ChipIdea driver, hence
> >>>>> the RPM is supported by both UDC and host controllers, secondly this opens
> >>>>> opportunity for implementing OTG support in the future.
> >>>>>
> >>>>> Patchset was tested on various Tegra20, Tegra30 and Tegra124 devices.
> >>>>> Thanks to Peter Geis, Matt Merhar, Nicolas Chauvet and Ion Agorria for
> >>>>> helping with the extensive and productive testing!
> >>>>>
> >>>>> Changelog:
> >>>>>
> >>>>> v3: - Replaced "goto" with if-statements as was suggested by Thierry Reding.
> >>>>>
> >>>>>     - Improved wording of the deprecated Kconfig entry as was suggested
> >>>>>       by Alan Stern.
> >>>>>
> >>>>>     - Added ACKs from Thierry Reding and Alan Stern.
> >>>>>
> >>>>>     - Added a new minor patch "Specify TX FIFO threshold in UDC SoC info"
> >>>>>       just for completeness, since we can now switch OTG to host mode in
> >>>>>       the ChipIdea driver. Although, OTG support remains a work-in-progress
> >>>>>       for now.
> >>>>>
> >>>>> v2: - Improved comments in the code as it was suggested by Peter Chen and
> >>>>>       Sergei Shtylyov for v1.
> >>>>>
> >>>>>     - Replaced mdelay() with fsleep() and made ci->hdc to reset to NULL in
> >>>>>       a error code path, like it was suggested by Peter Chen.
> >>>>>
> >>>>>     - Redirected deprecated USB_EHCI_TEGRA Kconfig entry to USB_CHIPIDEA_TEGRA
> >>>>>       as was suggested by Alan Stern.
> >>>>>
> >>>>>     - Improved commit message and added ACK from Thierry Reding to the patch
> >>>>>       that removes MODULE_ALIAS.
> >>>>>
> >>>>>     - Fixed UDC PHY waking up on ASUS TF201 tablet device by utilizing
> >>>>>       additional VBUS sensor. This was reported and tested by Ion Agorria.
> >>>>>
> >>>>>     - Added t-b from Ion Agorria.
> >>>>>
> >>>>> Dmitry Osipenko (8):
> >>>>>   usb: phy: tegra: Add delay after power up
> >>>>>   usb: phy: tegra: Support waking up from a low power mode
> >>>>>   usb: chipidea: tegra: Remove MODULE_ALIAS
> >>>>>   usb: chipidea: tegra: Rename UDC to USB
> >>>>>   usb: chipidea: tegra: Support runtime PM
> >>>>>   usb: chipidea: tegra: Specify TX FIFO threshold in UDC SoC info
> >>>>>   usb: host: ehci-tegra: Remove the driver
> >>>>>   ARM: tegra_defconfig: Enable USB_CHIPIDEA_HOST and remove
> >>>>>     USB_EHCI_TEGRA
> >>>>>
> >>>>> Peter Geis (1):
> >>>>>   usb: chipidea: tegra: Support host mode
> >>>>
> >>>> Chipidea related (patch 3-7) are applied, thanks.
> >>>
> >>> Hello Peter,
> >>>
> >>> Thank you for applying the patches.
> >>>
> >>> Who will apply the remaining patches?
> >>>
> >>> The Chipidea patch #6 depends on the PHY changes, otherwise USB will
> >>> suspend and never resume.
> >>>
> >>
> >> Peter, could you please apply the PHY and defconfig patches along with
> >> the CI patches to -next? I.e. the whole series. Preferentially in
> >> original ordering of patches should be preserved.
> >>
> > 
> > Hi Dmitry,
> > 
> > Usually, Greg could apply all USB patches, if I apply other USB related
> > patches, it may cause conflict with other patches in other's tree.
> > Greg, free feel to apply this series with 
> > Acked-by: Peter Chen <peter.chen@kernel.org>
> > for chipidea part.
> > 
> > For ARM defconfig patch, I think it should go ARM's tree.
> > 
> 
> Thank you for the answer!
> 
> It's not the ARM defconfig, but a local tegra_defconfig. It should be
> fine to take the patch via the USB tree since Thierry already acked it
> and asked to do so.
> 
> Greg, please take this whole series. Thanks in advance!

All now applied, thanks!

greg k-h

Re: [PATCH v3 0/9] Support Runtime PM and host mode by Tegra ChipIdea USB driver

[Dmitry Osipenko]

13.01.2021 13:27, Greg Kroah-Hartman пишет:
> On Wed, Jan 13, 2021 at 12:01:51PM +0300, Dmitry Osipenko wrote:
>> 13.01.2021 04:20, Peter Chen пишет:
>>> On 21-01-12 09:56:37, Dmitry Osipenko wrote:
>>>> 29.12.2020 17:26, Dmitry Osipenko пишет:
>>>>> 29.12.2020 08:16, Peter Chen пишет:
>>>>>> On 20-12-18 15:02:37, Dmitry Osipenko wrote:
>>>>>>> This series implements Runtime PM support for the Tegra ChipIdea USB driver.
>>>>>>> It also squashes the older ehci-tegra driver into the ChipIdea driver, hence
>>>>>>> the RPM is supported by both UDC and host controllers, secondly this opens
>>>>>>> opportunity for implementing OTG support in the future.
>>>>>>>
>>>>>>> Patchset was tested on various Tegra20, Tegra30 and Tegra124 devices.
>>>>>>> Thanks to Peter Geis, Matt Merhar, Nicolas Chauvet and Ion Agorria for
>>>>>>> helping with the extensive and productive testing!
>>>>>>>
>>>>>>> Changelog:
>>>>>>>
>>>>>>> v3: - Replaced "goto" with if-statements as was suggested by Thierry Reding.
>>>>>>>
>>>>>>>     - Improved wording of the deprecated Kconfig entry as was suggested
>>>>>>>       by Alan Stern.
>>>>>>>
>>>>>>>     - Added ACKs from Thierry Reding and Alan Stern.
>>>>>>>
>>>>>>>     - Added a new minor patch "Specify TX FIFO threshold in UDC SoC info"
>>>>>>>       just for completeness, since we can now switch OTG to host mode in
>>>>>>>       the ChipIdea driver. Although, OTG support remains a work-in-progress
>>>>>>>       for now.
>>>>>>>
>>>>>>> v2: - Improved comments in the code as it was suggested by Peter Chen and
>>>>>>>       Sergei Shtylyov for v1.
>>>>>>>
>>>>>>>     - Replaced mdelay() with fsleep() and made ci->hdc to reset to NULL in
>>>>>>>       a error code path, like it was suggested by Peter Chen.
>>>>>>>
>>>>>>>     - Redirected deprecated USB_EHCI_TEGRA Kconfig entry to USB_CHIPIDEA_TEGRA
>>>>>>>       as was suggested by Alan Stern.
>>>>>>>
>>>>>>>     - Improved commit message and added ACK from Thierry Reding to the patch
>>>>>>>       that removes MODULE_ALIAS.
>>>>>>>
>>>>>>>     - Fixed UDC PHY waking up on ASUS TF201 tablet device by utilizing
>>>>>>>       additional VBUS sensor. This was reported and tested by Ion Agorria.
>>>>>>>
>>>>>>>     - Added t-b from Ion Agorria.
>>>>>>>
>>>>>>> Dmitry Osipenko (8):
>>>>>>>   usb: phy: tegra: Add delay after power up
>>>>>>>   usb: phy: tegra: Support waking up from a low power mode
>>>>>>>   usb: chipidea: tegra: Remove MODULE_ALIAS
>>>>>>>   usb: chipidea: tegra: Rename UDC to USB
>>>>>>>   usb: chipidea: tegra: Support runtime PM
>>>>>>>   usb: chipidea: tegra: Specify TX FIFO threshold in UDC SoC info
>>>>>>>   usb: host: ehci-tegra: Remove the driver
>>>>>>>   ARM: tegra_defconfig: Enable USB_CHIPIDEA_HOST and remove
>>>>>>>     USB_EHCI_TEGRA
>>>>>>>
>>>>>>> Peter Geis (1):
>>>>>>>   usb: chipidea: tegra: Support host mode
>>>>>>
>>>>>> Chipidea related (patch 3-7) are applied, thanks.
>>>>>
>>>>> Hello Peter,
>>>>>
>>>>> Thank you for applying the patches.
>>>>>
>>>>> Who will apply the remaining patches?
>>>>>
>>>>> The Chipidea patch #6 depends on the PHY changes, otherwise USB will
>>>>> suspend and never resume.
>>>>>
>>>>
>>>> Peter, could you please apply the PHY and defconfig patches along with
>>>> the CI patches to -next? I.e. the whole series. Preferentially in
>>>> original ordering of patches should be preserved.
>>>>
>>>
>>> Hi Dmitry,
>>>
>>> Usually, Greg could apply all USB patches, if I apply other USB related
>>> patches, it may cause conflict with other patches in other's tree.
>>> Greg, free feel to apply this series with 
>>> Acked-by: Peter Chen <peter.chen@kernel.org>
>>> for chipidea part.
>>>
>>> For ARM defconfig patch, I think it should go ARM's tree.
>>>
>>
>> Thank you for the answer!
>>
>> It's not the ARM defconfig, but a local tegra_defconfig. It should be
>> fine to take the patch via the USB tree since Thierry already acked it
>> and asked to do so.
>>
>> Greg, please take this whole series. Thanks in advance!
> 
> All now applied, thanks!

Thank you!