* [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI @ 2024-02-27 22:04 Adam Ford 2024-02-27 22:04 ` [PATCH V7 1/6] dt-bindings: phy: add binding for the i.MX8MP HDMI PHY Adam Ford ` (7 more replies) 0 siblings, 8 replies; 10+ messages in thread From: Adam Ford @ 2024-02-27 22:04 UTC (permalink / raw) To: linux-arm-kernel, linux-phy Cc: aford, Adam Ford, Vinod Koul, Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, Lucas Stach, devicetree, imx, linux-kernel The i.MX8M Plus has an HDMI controller, which depends on several other systems. The Parallel Video Interface (PVI) and the HDMI-TX are already in the Linux-Next staging area 20240209, but the HDMI PHY driver and several device trees updates are still needed. This series is adapted from multiple series from Lucas Stach with edits and suggestions from feedback from various attempts, but it since it's difficult to use and test them independently, I merged them into on unified series. The version history is a bit ambiguous since different components were submitted at different times and had different amount of attempts. The previous attempt I did used the wrong starting point for the PHY, so this update includes a newer starting point with tags from that version and fixes from various people's feedback. I hope I caught them all, but I apologize if I missed something. Any tags from the previous attempt I made were intentionally dropped, because of the significant change, but I kept tags from the newer version I grabbed from patchwork. Because several items from the last attempt were merged, this series is only focussed on adding the HDMI PHY driver, and enabling the power domain, irqsteer interrupt controller, and HDMI pipeline in the device tree. The version numbers are a bit strange since these all got pulled from various attempts with different versions, but I wanted to push them together as a series to complete the pending work. This series restarted at V4 based on the version of the PHY driver and the other drivers and power-domain changes have been applied already. V7: Patch 5/7 marks the PVI driver disabled by default to prevent EPROBE_DEFER errors. No other changes to other patches in the series V6: Make the PHY driver depend on COMMON_CLK to fix build errors Make LCDIF3 disabled by default since it depends on hardware. V5 primarily updates feedback from the PHY driver itself, but a small adjustment was made to the register size in the device tree. Adam Ford (1): arm64: defconfig: Enable DRM_IMX8MP_DW_HDMI_BRIDGE as module Adam Ford (1): arm64: defconfig: Enable DRM_IMX8MP_DW_HDMI_BRIDGE as module Lucas Stach (5): dt-bindings: phy: add binding for the i.MX8MP HDMI PHY phy: freescale: add Samsung HDMI PHY arm64: dts: imx8mp: add HDMI power-domains arm64: dts: imx8mp: add HDMI irqsteer arm64: dts: imx8mp: add HDMI display pipeline .../bindings/phy/fsl,imx8mp-hdmi-phy.yaml | 62 ++ arch/arm64/boot/dts/freescale/imx8mp.dtsi | 147 ++++ arch/arm64/configs/defconfig | 1 + drivers/phy/freescale/Kconfig | 6 + drivers/phy/freescale/Makefile | 1 + drivers/phy/freescale/phy-fsl-samsung-hdmi.c | 720 ++++++++++++++++++ 6 files changed, 937 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/fsl,imx8mp-hdmi-phy.yaml create mode 100644 drivers/phy/freescale/phy-fsl-samsung-hdmi.c -- 2.43.0 ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V7 1/6] dt-bindings: phy: add binding for the i.MX8MP HDMI PHY 2024-02-27 22:04 [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Adam Ford @ 2024-02-27 22:04 ` Adam Ford 2024-02-27 22:04 ` [PATCH V7 2/6] phy: freescale: add Samsung " Adam Ford ` (6 subsequent siblings) 7 siblings, 0 replies; 10+ messages in thread From: Adam Ford @ 2024-02-27 22:04 UTC (permalink / raw) To: linux-arm-kernel, linux-phy Cc: aford, Lucas Stach, Adam Ford, Krzysztof Kozlowski, Luca Ceresoli, Vinod Koul, Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, devicetree, imx, linux-kernel From: Lucas Stach <l.stach@pengutronix.de> Add a DT binding for the HDMI PHY found on the i.MX8MP SoC. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> --- V6: No Change V5: No Change V4: No Change V3: Removed mintems at the request of Krzysztof and add his reviewed-by V2: I (Adam) tried to help move this along, so I took Lucas' patch and attempted to apply fixes based on feedback. I don't have all the history, so apologies for that. Added phy-cells to the required list and fixed an error due to the word 'binding' being in the title. --- .../bindings/phy/fsl,imx8mp-hdmi-phy.yaml | 62 +++++++++++++++++++ 1 file changed, 62 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/fsl,imx8mp-hdmi-phy.yaml diff --git a/Documentation/devicetree/bindings/phy/fsl,imx8mp-hdmi-phy.yaml b/Documentation/devicetree/bindings/phy/fsl,imx8mp-hdmi-phy.yaml new file mode 100644 index 000000000000..c43e86a8c2e0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/fsl,imx8mp-hdmi-phy.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/fsl,imx8mp-hdmi-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX8MP HDMI PHY + +maintainers: + - Lucas Stach <l.stach@pengutronix.de> + +properties: + compatible: + enum: + - fsl,imx8mp-hdmi-phy + + reg: + maxItems: 1 + + "#clock-cells": + const: 0 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: apb + - const: ref + + "#phy-cells": + const: 0 + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - "#clock-cells" + - clocks + - clock-names + - "#phy-cells" + - power-domains + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mp-clock.h> + #include <dt-bindings/power/imx8mp-power.h> + + phy@32fdff00 { + compatible = "fsl,imx8mp-hdmi-phy"; + reg = <0x32fdff00 0x100>; + clocks = <&clk IMX8MP_CLK_HDMI_APB>, + <&clk IMX8MP_CLK_HDMI_24M>; + clock-names = "apb", "ref"; + power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_HDMI_TX_PHY>; + #clock-cells = <0>; + #phy-cells = <0>; + }; -- 2.43.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V7 2/6] phy: freescale: add Samsung HDMI PHY 2024-02-27 22:04 [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Adam Ford 2024-02-27 22:04 ` [PATCH V7 1/6] dt-bindings: phy: add binding for the i.MX8MP HDMI PHY Adam Ford @ 2024-02-27 22:04 ` Adam Ford 2024-02-27 22:04 ` [PATCH V7 3/6] arm64: dts: imx8mp: add HDMI power-domains Adam Ford ` (5 subsequent siblings) 7 siblings, 0 replies; 10+ messages in thread From: Adam Ford @ 2024-02-27 22:04 UTC (permalink / raw) To: linux-arm-kernel, linux-phy Cc: aford, Lucas Stach, Luca Ceresoli, Richard Leitner, Marco Felsch, Alexander Stein, Frieder Schrempf, Adam Ford, Marek Vasut, Vinod Koul, Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, devicetree, imx, linux-kernel From: Lucas Stach <l.stach@pengutronix.de> This adds the driver for the Samsung HDMI PHY found on the i.MX8MP SoC. Based on downstream implementation from Sandor Yu <Sandor.yu@nxp.com>. According to the TRM, the PHY receives parallel data from the link and serializes it. It also sets the PLL clock needed for the TX serializer. Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> (v2) Tested-by: Richard Leitner <richard.leitner@skidata.com> (v2) Co-developed-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> # Kontron BL Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Marek Vasut <marex@denx.de> Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> --- V6: Set Kconfig dependency to include COMMON_CLK due to build errors V5: Remove an unnecessary include Migrate from of_clk_add_provider to of_clk_add_hw_provider Make const structures static Fix uninitialized variables and prevent div by 0 Mark PM functions as __maybe_unused V4: - I (Adam) added a comment in the code for clarifcation based on questions from Luca concerning a difference between the code and the ref manual. - Fixed the GENMASK on REG14 - Expanded the commit message briefly describing a bit more of what this driver does. - Removed some unnecessary include files. v3: - use GENMASK/FIELD_PREP - lowercase hex values - correct coding style v2: - use DEFINE_RUNTIME_DEV_PM_OPS --- drivers/phy/freescale/Kconfig | 6 + drivers/phy/freescale/Makefile | 1 + drivers/phy/freescale/phy-fsl-samsung-hdmi.c | 720 +++++++++++++++++++ 3 files changed, 727 insertions(+) create mode 100644 drivers/phy/freescale/phy-fsl-samsung-hdmi.c diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig index 853958fb2c06..45aaaea14fb4 100644 --- a/drivers/phy/freescale/Kconfig +++ b/drivers/phy/freescale/Kconfig @@ -35,6 +35,12 @@ config PHY_FSL_IMX8M_PCIE Enable this to add support for the PCIE PHY as found on i.MX8M family of SOCs. +config PHY_FSL_SAMSUNG_HDMI_PHY + tristate "Samsung HDMI PHY support" + depends on OF && HAS_IOMEM && COMMON_CLK + help + Enable this to add support for the Samsung HDMI PHY in i.MX8MP. + endif config PHY_FSL_LYNX_28G diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile index cedb328bc4d2..c4386bfdb853 100644 --- a/drivers/phy/freescale/Makefile +++ b/drivers/phy/freescale/Makefile @@ -4,3 +4,4 @@ obj-$(CONFIG_PHY_MIXEL_LVDS_PHY) += phy-fsl-imx8qm-lvds-phy.o obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) += phy-fsl-imx8-mipi-dphy.o obj-$(CONFIG_PHY_FSL_IMX8M_PCIE) += phy-fsl-imx8m-pcie.o obj-$(CONFIG_PHY_FSL_LYNX_28G) += phy-fsl-lynx-28g.o +obj-$(CONFIG_PHY_FSL_SAMSUNG_HDMI_PHY) += phy-fsl-samsung-hdmi.o diff --git a/drivers/phy/freescale/phy-fsl-samsung-hdmi.c b/drivers/phy/freescale/phy-fsl-samsung-hdmi.c new file mode 100644 index 000000000000..89e2c01f2ccf --- /dev/null +++ b/drivers/phy/freescale/phy-fsl-samsung-hdmi.c @@ -0,0 +1,720 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 NXP + * Copyright 2022 Pengutronix, Lucas Stach <kernel@pengutronix.de> + */ + +#include <linux/bitfield.h> +#include <linux/bits.h> +#include <linux/clk.h> +#include <linux/clk-provider.h> +#include <linux/delay.h> +#include <linux/iopoll.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/pm_runtime.h> + +#define PHY_REG_00 0x00 +#define PHY_REG_01 0x04 +#define PHY_REG_02 0x08 +#define PHY_REG_08 0x20 +#define PHY_REG_09 0x24 +#define PHY_REG_10 0x28 +#define PHY_REG_11 0x2c + +#define PHY_REG_12 0x30 +#define REG12_CK_DIV_MASK GENMASK(5, 4) + +#define PHY_REG_13 0x34 +#define REG13_TG_CODE_LOW_MASK GENMASK(7, 0) + +#define PHY_REG_14 0x38 +#define REG14_TOL_MASK GENMASK(7, 4) +#define REG14_RP_CODE_MASK GENMASK(3, 1) +#define REG14_TG_CODE_HIGH_MASK GENMASK(0, 0) + +#define PHY_REG_15 0x3c +#define PHY_REG_16 0x40 +#define PHY_REG_17 0x44 +#define PHY_REG_18 0x48 +#define PHY_REG_19 0x4c +#define PHY_REG_20 0x50 + +#define PHY_REG_21 0x54 +#define REG21_SEL_TX_CK_INV BIT(7) +#define REG21_PMS_S_MASK GENMASK(3, 0) + +#define PHY_REG_22 0x58 +#define PHY_REG_23 0x5c +#define PHY_REG_24 0x60 +#define PHY_REG_25 0x64 +#define PHY_REG_26 0x68 +#define PHY_REG_27 0x6c +#define PHY_REG_28 0x70 +#define PHY_REG_29 0x74 +#define PHY_REG_30 0x78 +#define PHY_REG_31 0x7c +#define PHY_REG_32 0x80 + +/* + * REG33 does not match the ref manual. According to Sandor Yu from NXP, + * "There is a doc issue on the i.MX8MP latest RM" + * REG33 is being used per guidance from Sandor + */ + +#define PHY_REG_33 0x84 +#define REG33_MODE_SET_DONE BIT(7) +#define REG33_FIX_DA BIT(1) + +#define PHY_REG_34 0x88 +#define REG34_PHY_READY BIT(7) +#define REG34_PLL_LOCK BIT(6) +#define REG34_PHY_CLK_READY BIT(5) + +#define PHY_REG_35 0x8c +#define PHY_REG_36 0x90 +#define PHY_REG_37 0x94 +#define PHY_REG_38 0x98 +#define PHY_REG_39 0x9c +#define PHY_REG_40 0xa0 +#define PHY_REG_41 0xa4 +#define PHY_REG_42 0xa8 +#define PHY_REG_43 0xac +#define PHY_REG_44 0xb0 +#define PHY_REG_45 0xb4 +#define PHY_REG_46 0xb8 +#define PHY_REG_47 0xbc + +#define PHY_PLL_DIV_REGS_NUM 6 + +struct phy_config { + u32 pixclk; + u8 pll_div_regs[PHY_PLL_DIV_REGS_NUM]; +}; + +static const struct phy_config phy_pll_cfg[] = { + { + .pixclk = 22250000, + .pll_div_regs = { 0x4b, 0xf1, 0x89, 0x88, 0x80, 0x40 }, + }, { + .pixclk = 23750000, + .pll_div_regs = { 0x50, 0xf1, 0x86, 0x85, 0x80, 0x40 }, + }, { + .pixclk = 24000000, + .pll_div_regs = { 0x50, 0xf0, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 24024000, + .pll_div_regs = { 0x50, 0xf1, 0x99, 0x02, 0x80, 0x40 }, + }, { + .pixclk = 25175000, + .pll_div_regs = { 0x54, 0xfc, 0xcc, 0x91, 0x80, 0x40 }, + }, { + .pixclk = 25200000, + .pll_div_regs = { 0x54, 0xf0, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 26750000, + .pll_div_regs = { 0x5a, 0xf2, 0x89, 0x88, 0x80, 0x40 }, + }, { + .pixclk = 27000000, + .pll_div_regs = { 0x5a, 0xf0, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 27027000, + .pll_div_regs = { 0x5a, 0xf2, 0xfd, 0x0c, 0x80, 0x40 }, + }, { + .pixclk = 29500000, + .pll_div_regs = { 0x62, 0xf4, 0x95, 0x08, 0x80, 0x40 }, + }, { + .pixclk = 30750000, + .pll_div_regs = { 0x66, 0xf4, 0x82, 0x01, 0x88, 0x45 }, + }, { + .pixclk = 30888000, + .pll_div_regs = { 0x66, 0xf4, 0x99, 0x18, 0x88, 0x45 }, + }, { + .pixclk = 33750000, + .pll_div_regs = { 0x70, 0xf4, 0x82, 0x01, 0x80, 0x40 }, + }, { + .pixclk = 35000000, + .pll_div_regs = { 0x58, 0xb8, 0x8b, 0x88, 0x80, 0x40 }, + }, { + .pixclk = 36000000, + .pll_div_regs = { 0x5a, 0xb0, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 36036000, + .pll_div_regs = { 0x5a, 0xb2, 0xfd, 0x0c, 0x80, 0x40 }, + }, { + .pixclk = 40000000, + .pll_div_regs = { 0x64, 0xb0, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 43200000, + .pll_div_regs = { 0x5a, 0x90, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 43243200, + .pll_div_regs = { 0x5a, 0x92, 0xfd, 0x0c, 0x80, 0x40 }, + }, { + .pixclk = 44500000, + .pll_div_regs = { 0x5c, 0x92, 0x98, 0x11, 0x84, 0x41 }, + }, { + .pixclk = 47000000, + .pll_div_regs = { 0x62, 0x94, 0x95, 0x82, 0x80, 0x40 }, + }, { + .pixclk = 47500000, + .pll_div_regs = { 0x63, 0x96, 0xa1, 0x82, 0x80, 0x40 }, + }, { + .pixclk = 50349650, + .pll_div_regs = { 0x54, 0x7c, 0xc3, 0x8f, 0x80, 0x40 }, + }, { + .pixclk = 50400000, + .pll_div_regs = { 0x54, 0x70, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 53250000, + .pll_div_regs = { 0x58, 0x72, 0x84, 0x03, 0x82, 0x41 }, + }, { + .pixclk = 53500000, + .pll_div_regs = { 0x5a, 0x72, 0x89, 0x88, 0x80, 0x40 }, + }, { + .pixclk = 54000000, + .pll_div_regs = { 0x5a, 0x70, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 54054000, + .pll_div_regs = { 0x5a, 0x72, 0xfd, 0x0c, 0x80, 0x40 }, + }, { + .pixclk = 59000000, + .pll_div_regs = { 0x62, 0x74, 0x95, 0x08, 0x80, 0x40 }, + }, { + .pixclk = 59340659, + .pll_div_regs = { 0x62, 0x74, 0xdb, 0x52, 0x88, 0x47 }, + }, { + .pixclk = 59400000, + .pll_div_regs = { 0x63, 0x70, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 61500000, + .pll_div_regs = { 0x66, 0x74, 0x82, 0x01, 0x88, 0x45 }, + }, { + .pixclk = 63500000, + .pll_div_regs = { 0x69, 0x74, 0x89, 0x08, 0x80, 0x40 }, + }, { + .pixclk = 67500000, + .pll_div_regs = { 0x54, 0x52, 0x87, 0x03, 0x80, 0x40 }, + }, { + .pixclk = 70000000, + .pll_div_regs = { 0x58, 0x58, 0x8b, 0x88, 0x80, 0x40 }, + }, { + .pixclk = 72000000, + .pll_div_regs = { 0x5a, 0x50, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 72072000, + .pll_div_regs = { 0x5a, 0x52, 0xfd, 0x0c, 0x80, 0x40 }, + }, { + .pixclk = 74176000, + .pll_div_regs = { 0x5d, 0x58, 0xdb, 0xA2, 0x88, 0x41 }, + }, { + .pixclk = 74250000, + .pll_div_regs = { 0x5c, 0x52, 0x90, 0x0d, 0x84, 0x41 }, + }, { + .pixclk = 78500000, + .pll_div_regs = { 0x62, 0x54, 0x87, 0x01, 0x80, 0x40 }, + }, { + .pixclk = 80000000, + .pll_div_regs = { 0x64, 0x50, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 82000000, + .pll_div_regs = { 0x66, 0x54, 0x82, 0x01, 0x88, 0x45 }, + }, { + .pixclk = 82500000, + .pll_div_regs = { 0x67, 0x54, 0x88, 0x01, 0x90, 0x49 }, + }, { + .pixclk = 89000000, + .pll_div_regs = { 0x70, 0x54, 0x84, 0x83, 0x80, 0x40 }, + }, { + .pixclk = 90000000, + .pll_div_regs = { 0x70, 0x54, 0x82, 0x01, 0x80, 0x40 }, + }, { + .pixclk = 94000000, + .pll_div_regs = { 0x4e, 0x32, 0xa7, 0x10, 0x80, 0x40 }, + }, { + .pixclk = 95000000, + .pll_div_regs = { 0x50, 0x31, 0x86, 0x85, 0x80, 0x40 }, + }, { + .pixclk = 98901099, + .pll_div_regs = { 0x52, 0x3a, 0xdb, 0x4c, 0x88, 0x47 }, + }, { + .pixclk = 99000000, + .pll_div_regs = { 0x52, 0x32, 0x82, 0x01, 0x88, 0x47 }, + }, { + .pixclk = 100699300, + .pll_div_regs = { 0x54, 0x3c, 0xc3, 0x8f, 0x80, 0x40 }, + }, { + .pixclk = 100800000, + .pll_div_regs = { 0x54, 0x30, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 102500000, + .pll_div_regs = { 0x55, 0x32, 0x8c, 0x05, 0x90, 0x4b }, + }, { + .pixclk = 104750000, + .pll_div_regs = { 0x57, 0x32, 0x98, 0x07, 0x90, 0x49 }, + }, { + .pixclk = 106500000, + .pll_div_regs = { 0x58, 0x32, 0x84, 0x03, 0x82, 0x41 }, + }, { + .pixclk = 107000000, + .pll_div_regs = { 0x5a, 0x32, 0x89, 0x88, 0x80, 0x40 }, + }, { + .pixclk = 108000000, + .pll_div_regs = { 0x5a, 0x30, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 108108000, + .pll_div_regs = { 0x5a, 0x32, 0xfd, 0x0c, 0x80, 0x40 }, + }, { + .pixclk = 118000000, + .pll_div_regs = { 0x62, 0x34, 0x95, 0x08, 0x80, 0x40 }, + }, { + .pixclk = 118800000, + .pll_div_regs = { 0x63, 0x30, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 123000000, + .pll_div_regs = { 0x66, 0x34, 0x82, 0x01, 0x88, 0x45 }, + }, { + .pixclk = 127000000, + .pll_div_regs = { 0x69, 0x34, 0x89, 0x08, 0x80, 0x40 }, + }, { + .pixclk = 135000000, + .pll_div_regs = { 0x70, 0x34, 0x82, 0x01, 0x80, 0x40 }, + }, { + .pixclk = 135580000, + .pll_div_regs = { 0x71, 0x39, 0xe9, 0x82, 0x9c, 0x5b }, + }, { + .pixclk = 137520000, + .pll_div_regs = { 0x72, 0x38, 0x99, 0x10, 0x85, 0x41 }, + }, { + .pixclk = 138750000, + .pll_div_regs = { 0x73, 0x35, 0x88, 0x05, 0x90, 0x4d }, + }, { + .pixclk = 140000000, + .pll_div_regs = { 0x75, 0x36, 0xa7, 0x90, 0x80, 0x40 }, + }, { + .pixclk = 144000000, + .pll_div_regs = { 0x78, 0x30, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 148352000, + .pll_div_regs = { 0x7b, 0x35, 0xdb, 0x39, 0x90, 0x45 }, + }, { + .pixclk = 148500000, + .pll_div_regs = { 0x7b, 0x35, 0x84, 0x03, 0x90, 0x45 }, + }, { + .pixclk = 154000000, + .pll_div_regs = { 0x40, 0x18, 0x83, 0x01, 0x00, 0x40 }, + }, { + .pixclk = 157000000, + .pll_div_regs = { 0x41, 0x11, 0xa7, 0x14, 0x80, 0x40 }, + }, { + .pixclk = 160000000, + .pll_div_regs = { 0x42, 0x12, 0xa1, 0x20, 0x80, 0x40 }, + }, { + .pixclk = 162000000, + .pll_div_regs = { 0x43, 0x18, 0x8b, 0x08, 0x96, 0x55 }, + }, { + .pixclk = 164000000, + .pll_div_regs = { 0x45, 0x11, 0x83, 0x82, 0x90, 0x4b }, + }, { + .pixclk = 165000000, + .pll_div_regs = { 0x45, 0x11, 0x84, 0x81, 0x90, 0x4b }, + }, { + .pixclk = 180000000, + .pll_div_regs = { 0x4b, 0x10, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 185625000, + .pll_div_regs = { 0x4e, 0x12, 0x9a, 0x95, 0x80, 0x40 }, + }, { + .pixclk = 188000000, + .pll_div_regs = { 0x4e, 0x12, 0xa7, 0x10, 0x80, 0x40 }, + }, { + .pixclk = 198000000, + .pll_div_regs = { 0x52, 0x12, 0x82, 0x01, 0x88, 0x47 }, + }, { + .pixclk = 205000000, + .pll_div_regs = { 0x55, 0x12, 0x8c, 0x05, 0x90, 0x4b }, + }, { + .pixclk = 209500000, + .pll_div_regs = { 0x57, 0x12, 0x98, 0x07, 0x90, 0x49 }, + }, { + .pixclk = 213000000, + .pll_div_regs = { 0x58, 0x12, 0x84, 0x03, 0x82, 0x41 }, + }, { + .pixclk = 216000000, + .pll_div_regs = { 0x5a, 0x10, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 216216000, + .pll_div_regs = { 0x5a, 0x12, 0xfd, 0x0c, 0x80, 0x40 }, + }, { + .pixclk = 237600000, + .pll_div_regs = { 0x63, 0x10, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 254000000, + .pll_div_regs = { 0x69, 0x14, 0x89, 0x08, 0x80, 0x40 }, + }, { + .pixclk = 277500000, + .pll_div_regs = { 0x73, 0x15, 0x88, 0x05, 0x90, 0x4d }, + }, { + .pixclk = 288000000, + .pll_div_regs = { 0x78, 0x10, 0x00, 0x00, 0x80, 0x00 }, + }, { + .pixclk = 297000000, + .pll_div_regs = { 0x7b, 0x15, 0x84, 0x03, 0x90, 0x45 }, + }, +}; + +struct reg_settings { + u8 reg; + u8 val; +}; + +static const struct reg_settings common_phy_cfg[] = { + { PHY_REG_00, 0x00 }, { PHY_REG_01, 0xd1 }, + { PHY_REG_08, 0x4f }, { PHY_REG_09, 0x30 }, + { PHY_REG_10, 0x33 }, { PHY_REG_11, 0x65 }, + /* REG12 pixclk specific */ + /* REG13 pixclk specific */ + /* REG14 pixclk specific */ + { PHY_REG_15, 0x80 }, { PHY_REG_16, 0x6c }, + { PHY_REG_17, 0xf2 }, { PHY_REG_18, 0x67 }, + { PHY_REG_19, 0x00 }, { PHY_REG_20, 0x10 }, + /* REG21 pixclk specific */ + { PHY_REG_22, 0x30 }, { PHY_REG_23, 0x32 }, + { PHY_REG_24, 0x60 }, { PHY_REG_25, 0x8f }, + { PHY_REG_26, 0x00 }, { PHY_REG_27, 0x00 }, + { PHY_REG_28, 0x08 }, { PHY_REG_29, 0x00 }, + { PHY_REG_30, 0x00 }, { PHY_REG_31, 0x00 }, + { PHY_REG_32, 0x00 }, { PHY_REG_33, 0x80 }, + { PHY_REG_34, 0x00 }, { PHY_REG_35, 0x00 }, + { PHY_REG_36, 0x00 }, { PHY_REG_37, 0x00 }, + { PHY_REG_38, 0x00 }, { PHY_REG_39, 0x00 }, + { PHY_REG_40, 0x00 }, { PHY_REG_41, 0xe0 }, + { PHY_REG_42, 0x83 }, { PHY_REG_43, 0x0f }, + { PHY_REG_44, 0x3E }, { PHY_REG_45, 0xf8 }, + { PHY_REG_46, 0x00 }, { PHY_REG_47, 0x00 } +}; + +struct fsl_samsung_hdmi_phy { + struct device *dev; + void __iomem *regs; + struct clk *apbclk; + struct clk *refclk; + + /* clk provider */ + struct clk_hw hw; + const struct phy_config *cur_cfg; +}; + +static inline struct fsl_samsung_hdmi_phy * +to_fsl_samsung_hdmi_phy(struct clk_hw *hw) +{ + return container_of(hw, struct fsl_samsung_hdmi_phy, hw); +} + +static void +fsl_samsung_hdmi_phy_configure_pixclk(struct fsl_samsung_hdmi_phy *phy, + const struct phy_config *cfg) +{ + u8 div = 0x1; + + switch (cfg->pixclk) { + case 22250000 ... 33750000: + div = 0xf; + break; + case 35000000 ... 40000000: + div = 0xb; + break; + case 43200000 ... 47500000: + div = 0x9; + break; + case 50349650 ... 63500000: + div = 0x7; + break; + case 67500000 ... 90000000: + div = 0x5; + break; + case 94000000 ... 148500000: + div = 0x3; + break; + case 154000000 ... 297000000: + div = 0x1; + break; + } + + writeb(REG21_SEL_TX_CK_INV | FIELD_PREP(REG21_PMS_S_MASK, div), + phy->regs + PHY_REG_21); +} + +static void +fsl_samsung_hdmi_phy_configure_pll_lock_det(struct fsl_samsung_hdmi_phy *phy, + const struct phy_config *cfg) +{ + u32 pclk = cfg->pixclk; + u32 fld_tg_code; + u32 pclk_khz; + u8 div = 1; + + switch (cfg->pixclk) { + case 22250000 ... 47500000: + div = 1; + break; + case 50349650 ... 99000000: + div = 2; + break; + case 100699300 ... 198000000: + div = 4; + break; + case 205000000 ... 297000000: + div = 8; + break; + } + + writeb(FIELD_PREP(REG12_CK_DIV_MASK, ilog2(div)), phy->regs + PHY_REG_12); + + /* + * Calculation for the frequency lock detector target code (fld_tg_code) + * is based on reference manual register description of PHY_REG13 + * (13.10.3.1.14.2): + * 1st) Calculate int_pllclk which is determinded by FLD_CK_DIV + * 2nd) Increase resolution to avoid rounding issues + * 3th) Do the div (256 / Freq. of int_pllclk) * 24 + * 4th) Reduce the resolution and always round up since the NXP + * settings rounding up always too. TODO: Check if that is + * correct. + */ + pclk /= div; + pclk_khz = pclk / 1000; + fld_tg_code = 256 * 1000 * 1000 / pclk_khz * 24; + fld_tg_code = DIV_ROUND_UP(fld_tg_code, 1000); + + /* FLD_TOL and FLD_RP_CODE taken from downstream driver */ + writeb(FIELD_PREP(REG13_TG_CODE_LOW_MASK, fld_tg_code), + phy->regs + PHY_REG_13); + writeb(FIELD_PREP(REG14_TOL_MASK, 2) | + FIELD_PREP(REG14_RP_CODE_MASK, 2) | + FIELD_PREP(REG14_TG_CODE_HIGH_MASK, fld_tg_code >> 8), + phy->regs + PHY_REG_14); +} + +static int fsl_samsung_hdmi_phy_configure(struct fsl_samsung_hdmi_phy *phy, + const struct phy_config *cfg) +{ + int i, ret; + u8 val; + + /* HDMI PHY init */ + writeb(REG33_FIX_DA, phy->regs + PHY_REG_33); + + /* common PHY registers */ + for (i = 0; i < ARRAY_SIZE(common_phy_cfg); i++) + writeb(common_phy_cfg[i].val, phy->regs + common_phy_cfg[i].reg); + + /* set individual PLL registers PHY_REG2 ... PHY_REG7 */ + for (i = 0; i < PHY_PLL_DIV_REGS_NUM; i++) + writeb(cfg->pll_div_regs[i], phy->regs + PHY_REG_02 + i * 4); + + fsl_samsung_hdmi_phy_configure_pixclk(phy, cfg); + fsl_samsung_hdmi_phy_configure_pll_lock_det(phy, cfg); + + writeb(REG33_FIX_DA | REG33_MODE_SET_DONE, phy->regs + PHY_REG_33); + + ret = readb_poll_timeout(phy->regs + PHY_REG_34, val, + val & REG34_PLL_LOCK, 50, 20000); + if (ret) + dev_err(phy->dev, "PLL failed to lock\n"); + + return ret; +} + +static unsigned long phy_clk_recalc_rate(struct clk_hw *hw, + unsigned long parent_rate) +{ + struct fsl_samsung_hdmi_phy *phy = to_fsl_samsung_hdmi_phy(hw); + + if (!phy->cur_cfg) + return 74250000; + + return phy->cur_cfg->pixclk; +} + +static long phy_clk_round_rate(struct clk_hw *hw, + unsigned long rate, unsigned long *parent_rate) +{ + int i; + + for (i = ARRAY_SIZE(phy_pll_cfg) - 1; i >= 0; i--) + if (phy_pll_cfg[i].pixclk <= rate) + return phy_pll_cfg[i].pixclk; + + return -EINVAL; +} + +static int phy_clk_set_rate(struct clk_hw *hw, + unsigned long rate, unsigned long parent_rate) +{ + struct fsl_samsung_hdmi_phy *phy = to_fsl_samsung_hdmi_phy(hw); + int i; + + for (i = ARRAY_SIZE(phy_pll_cfg) - 1; i >= 0; i--) + if (phy_pll_cfg[i].pixclk <= rate) + break; + + if (i < 0) + return -EINVAL; + + phy->cur_cfg = &phy_pll_cfg[i]; + + return fsl_samsung_hdmi_phy_configure(phy, phy->cur_cfg); +} + +static const struct clk_ops phy_clk_ops = { + .recalc_rate = phy_clk_recalc_rate, + .round_rate = phy_clk_round_rate, + .set_rate = phy_clk_set_rate, +}; + +static int phy_clk_register(struct fsl_samsung_hdmi_phy *phy) +{ + struct device *dev = phy->dev; + struct device_node *np = dev->of_node; + struct clk_init_data init; + const char *parent_name; + struct clk *phyclk; + int ret; + + parent_name = __clk_get_name(phy->refclk); + + init.parent_names = &parent_name; + init.num_parents = 1; + init.flags = 0; + init.name = "hdmi_pclk"; + init.ops = &phy_clk_ops; + + phy->hw.init = &init; + + phyclk = devm_clk_register(dev, &phy->hw); + if (IS_ERR(phyclk)) + return dev_err_probe(dev, PTR_ERR(phyclk), + "failed to register clock\n"); + + ret = of_clk_add_hw_provider(np, of_clk_hw_simple_get, phyclk); + if (ret) + return dev_err_probe(dev, ret, + "failed to register clock provider\n"); + + return 0; +} + +static int fsl_samsung_hdmi_phy_probe(struct platform_device *pdev) +{ + struct fsl_samsung_hdmi_phy *phy; + int ret; + + phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL); + if (!phy) + return -ENOMEM; + + platform_set_drvdata(pdev, phy); + phy->dev = &pdev->dev; + + phy->regs = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(phy->regs)) + return PTR_ERR(phy->regs); + + phy->apbclk = devm_clk_get(phy->dev, "apb"); + if (IS_ERR(phy->apbclk)) + return dev_err_probe(phy->dev, PTR_ERR(phy->apbclk), + "failed to get apb clk\n"); + + phy->refclk = devm_clk_get(phy->dev, "ref"); + if (IS_ERR(phy->refclk)) + return dev_err_probe(phy->dev, PTR_ERR(phy->refclk), + "failed to get ref clk\n"); + + ret = clk_prepare_enable(phy->apbclk); + if (ret) { + dev_err(phy->dev, "failed to enable apbclk\n"); + return ret; + } + + pm_runtime_get_noresume(phy->dev); + pm_runtime_set_active(phy->dev); + pm_runtime_enable(phy->dev); + + ret = phy_clk_register(phy); + if (ret) { + dev_err(&pdev->dev, "register clk failed\n"); + goto register_clk_failed; + } + + pm_runtime_put(phy->dev); + + return 0; + +register_clk_failed: + clk_disable_unprepare(phy->apbclk); + + return ret; +} + +static int fsl_samsung_hdmi_phy_remove(struct platform_device *pdev) +{ + of_clk_del_provider(pdev->dev.of_node); + + return 0; +} + +static int __maybe_unused fsl_samsung_hdmi_phy_suspend(struct device *dev) +{ + struct fsl_samsung_hdmi_phy *phy = dev_get_drvdata(dev); + + clk_disable_unprepare(phy->apbclk); + + return 0; +} + +static int __maybe_unused fsl_samsung_hdmi_phy_resume(struct device *dev) +{ + struct fsl_samsung_hdmi_phy *phy = dev_get_drvdata(dev); + int ret = 0; + + ret = clk_prepare_enable(phy->apbclk); + if (ret) { + dev_err(phy->dev, "failed to enable apbclk\n"); + return ret; + } + + if (phy->cur_cfg) + ret = fsl_samsung_hdmi_phy_configure(phy, phy->cur_cfg); + + return ret; + +} + +static DEFINE_RUNTIME_DEV_PM_OPS(fsl_samsung_hdmi_phy_pm_ops, + fsl_samsung_hdmi_phy_suspend, + fsl_samsung_hdmi_phy_resume, NULL); + +static const struct of_device_id fsl_samsung_hdmi_phy_of_match[] = { + { + .compatible = "fsl,imx8mp-hdmi-phy", + }, { + /* sentinel */ + } +}; +MODULE_DEVICE_TABLE(of, fsl_samsung_hdmi_phy_of_match); + +static struct platform_driver fsl_samsung_hdmi_phy_driver = { + .probe = fsl_samsung_hdmi_phy_probe, + .remove = fsl_samsung_hdmi_phy_remove, + .driver = { + .name = "fsl-samsung-hdmi-phy", + .of_match_table = fsl_samsung_hdmi_phy_of_match, + .pm = pm_ptr(&fsl_samsung_hdmi_phy_pm_ops), + }, +}; +module_platform_driver(fsl_samsung_hdmi_phy_driver); + +MODULE_AUTHOR("Sandor Yu <Sandor.yu@nxp.com>"); +MODULE_DESCRIPTION("SAMSUNG HDMI 2.0 Transmitter PHY Driver"); +MODULE_LICENSE("GPL"); -- 2.43.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V7 3/6] arm64: dts: imx8mp: add HDMI power-domains 2024-02-27 22:04 [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Adam Ford 2024-02-27 22:04 ` [PATCH V7 1/6] dt-bindings: phy: add binding for the i.MX8MP HDMI PHY Adam Ford 2024-02-27 22:04 ` [PATCH V7 2/6] phy: freescale: add Samsung " Adam Ford @ 2024-02-27 22:04 ` Adam Ford 2024-03-29 3:19 ` Shawn Guo 2024-02-27 22:04 ` [PATCH V7 4/6] arm64: dts: imx8mp: add HDMI irqsteer Adam Ford ` (4 subsequent siblings) 7 siblings, 1 reply; 10+ messages in thread From: Adam Ford @ 2024-02-27 22:04 UTC (permalink / raw) To: linux-arm-kernel, linux-phy Cc: aford, Lucas Stach, Adam Ford, Marek Vasut, Luca Ceresoli, Vinod Koul, Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, devicetree, imx, linux-kernel From: Lucas Stach <l.stach@pengutronix.de> This adds the PGC and HDMI blk-ctrl nodes providing power control for HDMI subsystem peripherals. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Marek Vasut <marex@denx.de> Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> --- V6: No Change V5: No Change V4: No Change V3: The hdmi_blk_ctrl was in the wrong place, so move it to AIPS4. power-domains@ fixed to read power-domain@ V2: Add missing power-domains hdcp and hrv --- arch/arm64/boot/dts/freescale/imx8mp.dtsi | 38 +++++++++++++++++++++++ 1 file changed, 38 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index bfc5c81a5bd4..c9bcb6641de7 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -836,6 +836,23 @@ pgc_mediamix: power-domain@10 { <&clk IMX8MP_CLK_MEDIA_APB_ROOT>; }; + pgc_hdmimix: power-domain@14 { + #power-domain-cells = <0>; + reg = <IMX8MP_POWER_DOMAIN_HDMIMIX>; + clocks = <&clk IMX8MP_CLK_HDMI_ROOT>, + <&clk IMX8MP_CLK_HDMI_APB>; + assigned-clocks = <&clk IMX8MP_CLK_HDMI_AXI>, + <&clk IMX8MP_CLK_HDMI_APB>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>, + <&clk IMX8MP_SYS_PLL1_133M>; + assigned-clock-rates = <500000000>, <133000000>; + }; + + pgc_hdmi_phy: power-domain@15 { + #power-domain-cells = <0>; + reg = <IMX8MP_POWER_DOMAIN_HDMI_PHY>; + }; + pgc_mipi_phy2: power-domain@16 { #power-domain-cells = <0>; reg = <IMX8MP_POWER_DOMAIN_MIPI_PHY2>; @@ -1889,6 +1906,27 @@ hsio_blk_ctrl: blk-ctrl@32f10000 { #power-domain-cells = <1>; #clock-cells = <0>; }; + + hdmi_blk_ctrl: blk-ctrl@32fc0000 { + compatible = "fsl,imx8mp-hdmi-blk-ctrl", "syscon"; + reg = <0x32fc0000 0x1000>; + clocks = <&clk IMX8MP_CLK_HDMI_APB>, + <&clk IMX8MP_CLK_HDMI_ROOT>, + <&clk IMX8MP_CLK_HDMI_REF_266M>, + <&clk IMX8MP_CLK_HDMI_24M>, + <&clk IMX8MP_CLK_HDMI_FDCC_TST>; + clock-names = "apb", "axi", "ref_266m", "ref_24m", "fdcc"; + power-domains = <&pgc_hdmimix>, <&pgc_hdmimix>, + <&pgc_hdmimix>, <&pgc_hdmimix>, + <&pgc_hdmimix>, <&pgc_hdmimix>, + <&pgc_hdmimix>, <&pgc_hdmi_phy>, + <&pgc_hdmimix>, <&pgc_hdmimix>; + power-domain-names = "bus", "irqsteer", "lcdif", + "pai", "pvi", "trng", + "hdmi-tx", "hdmi-tx-phy", + "hdcp", "hrv"; + #power-domain-cells = <1>; + }; }; pcie: pcie@33800000 { -- 2.43.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH V7 3/6] arm64: dts: imx8mp: add HDMI power-domains 2024-02-27 22:04 ` [PATCH V7 3/6] arm64: dts: imx8mp: add HDMI power-domains Adam Ford @ 2024-03-29 3:19 ` Shawn Guo 0 siblings, 0 replies; 10+ messages in thread From: Shawn Guo @ 2024-03-29 3:19 UTC (permalink / raw) To: Adam Ford Cc: linux-arm-kernel, linux-phy, aford, Lucas Stach, Marek Vasut, Luca Ceresoli, Vinod Koul, Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, devicetree, imx, linux-kernel On Tue, Feb 27, 2024 at 04:04:37PM -0600, Adam Ford wrote: > From: Lucas Stach <l.stach@pengutronix.de> > > This adds the PGC and HDMI blk-ctrl nodes providing power control for > HDMI subsystem peripherals. > > Signed-off-by: Adam Ford <aford173@gmail.com> > Signed-off-by: Lucas Stach <l.stach@pengutronix.de> > Tested-by: Marek Vasut <marex@denx.de> > Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> Applied 3 ~ 6, thanks! ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V7 4/6] arm64: dts: imx8mp: add HDMI irqsteer 2024-02-27 22:04 [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Adam Ford ` (2 preceding siblings ...) 2024-02-27 22:04 ` [PATCH V7 3/6] arm64: dts: imx8mp: add HDMI power-domains Adam Ford @ 2024-02-27 22:04 ` Adam Ford 2024-02-27 22:04 ` [PATCH V7 5/6] arm64: dts: imx8mp: add HDMI display pipeline Adam Ford ` (3 subsequent siblings) 7 siblings, 0 replies; 10+ messages in thread From: Adam Ford @ 2024-02-27 22:04 UTC (permalink / raw) To: linux-arm-kernel, linux-phy Cc: aford, Lucas Stach, Adam Ford, Marek Vasut, Luca Ceresoli, Vinod Koul, Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, devicetree, imx, linux-kernel From: Lucas Stach <l.stach@pengutronix.de> The HDMI irqsteer is a secondary interrupt controller within the HDMI subsystem that maps all HDMI peripheral IRQs into a single upstream IRQ line. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Marek Vasut <marex@denx.de> Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> --- V6: No Change V5: Increase size to 4KB to match the ref manual V2: Add my (Adam) s-o-b and re-order position under AIPS4 --- arch/arm64/boot/dts/freescale/imx8mp.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index c9bcb6641de7..18bfa7d9aa7f 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -1927,6 +1927,19 @@ hdmi_blk_ctrl: blk-ctrl@32fc0000 { "hdcp", "hrv"; #power-domain-cells = <1>; }; + + irqsteer_hdmi: interrupt-controller@32fc2000 { + compatible = "fsl,imx-irqsteer"; + reg = <0x32fc2000 0x1000>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + fsl,channel = <1>; + fsl,num-irqs = <64>; + clocks = <&clk IMX8MP_CLK_HDMI_APB>; + clock-names = "ipg"; + power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_IRQSTEER>; + }; }; pcie: pcie@33800000 { -- 2.43.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V7 5/6] arm64: dts: imx8mp: add HDMI display pipeline 2024-02-27 22:04 [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Adam Ford ` (3 preceding siblings ...) 2024-02-27 22:04 ` [PATCH V7 4/6] arm64: dts: imx8mp: add HDMI irqsteer Adam Ford @ 2024-02-27 22:04 ` Adam Ford 2024-02-27 22:04 ` [PATCH V7 6/6] arm64: defconfig: Enable DRM_IMX8MP_DW_HDMI_BRIDGE as module Adam Ford ` (2 subsequent siblings) 7 siblings, 0 replies; 10+ messages in thread From: Adam Ford @ 2024-02-27 22:04 UTC (permalink / raw) To: linux-arm-kernel, linux-phy Cc: aford, Lucas Stach, Adam Ford, Marek Vasut, Luca Ceresoli, Vinod Koul, Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, devicetree, imx, linux-kernel From: Lucas Stach <l.stach@pengutronix.de> This adds the DT nodes for all the peripherals that make up the HDMI display pipeline. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Marek Vasut <marex@denx.de> Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> --- V7: Make PVI node disabled by default to avoid EPROBE_DEFER V6: Make LCDIF3 disabled by default V5: No change V3: Re-ordered the HDMI parts to properly come after irqstree_hdmi inside AIPS4. Change size of LCDIF3 and PVI to match TRM sizes of 4KB. V2: I took this from Lucas' original submission with the following: Removed extra clock from HDMI-TX since it is now part of the power domain Added interrupt-parent to PVI Changed the name of the HDMI tranmitter to fsl,imx8mp-hdmi-tx Added ports to HDMI-tx --- arch/arm64/boot/dts/freescale/imx8mp.dtsi | 96 +++++++++++++++++++++++ 1 file changed, 96 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index 18bfa7d9aa7f..e3510fef6030 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -1940,6 +1940,102 @@ irqsteer_hdmi: interrupt-controller@32fc2000 { clock-names = "ipg"; power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_IRQSTEER>; }; + + hdmi_pvi: display-bridge@32fc4000 { + compatible = "fsl,imx8mp-hdmi-pvi"; + reg = <0x32fc4000 0x1000>; + interrupt-parent = <&irqsteer_hdmi>; + interrupts = <12>; + power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_PVI>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + pvi_from_lcdif3: endpoint { + remote-endpoint = <&lcdif3_to_pvi>; + }; + }; + + port@1 { + reg = <1>; + pvi_to_hdmi_tx: endpoint { + remote-endpoint = <&hdmi_tx_from_pvi>; + }; + }; + }; + }; + + lcdif3: display-controller@32fc6000 { + compatible = "fsl,imx8mp-lcdif"; + reg = <0x32fc6000 0x1000>; + interrupt-parent = <&irqsteer_hdmi>; + interrupts = <8>; + clocks = <&hdmi_tx_phy>, + <&clk IMX8MP_CLK_HDMI_APB>, + <&clk IMX8MP_CLK_HDMI_ROOT>; + clock-names = "pix", "axi", "disp_axi"; + power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_LCDIF>; + status = "disabled"; + + port { + lcdif3_to_pvi: endpoint { + remote-endpoint = <&pvi_from_lcdif3>; + }; + }; + }; + + hdmi_tx: hdmi@32fd8000 { + compatible = "fsl,imx8mp-hdmi-tx"; + reg = <0x32fd8000 0x7eff>; + interrupt-parent = <&irqsteer_hdmi>; + interrupts = <0>; + clocks = <&clk IMX8MP_CLK_HDMI_APB>, + <&clk IMX8MP_CLK_HDMI_REF_266M>, + <&clk IMX8MP_CLK_32K>, + <&hdmi_tx_phy>; + clock-names = "iahb", "isfr", "cec", "pix"; + assigned-clocks = <&clk IMX8MP_CLK_HDMI_REF_266M>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>; + power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_HDMI_TX>; + reg-io-width = <1>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hdmi_tx_from_pvi: endpoint { + remote-endpoint = <&pvi_to_hdmi_tx>; + }; + }; + + port@1 { + reg = <1>; + /* Point endpoint to the HDMI connector */ + }; + }; + }; + + hdmi_tx_phy: phy@32fdff00 { + compatible = "fsl,imx8mp-hdmi-phy"; + reg = <0x32fdff00 0x100>; + clocks = <&clk IMX8MP_CLK_HDMI_APB>, + <&clk IMX8MP_CLK_HDMI_24M>; + clock-names = "apb", "ref"; + assigned-clocks = <&clk IMX8MP_CLK_HDMI_24M>; + assigned-clock-parents = <&clk IMX8MP_CLK_24M>; + power-domains = <&hdmi_blk_ctrl IMX8MP_HDMIBLK_PD_HDMI_TX_PHY>; + #clock-cells = <0>; + #phy-cells = <0>; + status = "disabled"; + }; }; pcie: pcie@33800000 { -- 2.43.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V7 6/6] arm64: defconfig: Enable DRM_IMX8MP_DW_HDMI_BRIDGE as module 2024-02-27 22:04 [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Adam Ford ` (4 preceding siblings ...) 2024-02-27 22:04 ` [PATCH V7 5/6] arm64: dts: imx8mp: add HDMI display pipeline Adam Ford @ 2024-02-27 22:04 ` Adam Ford 2024-03-26 9:13 ` [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Tommaso Merciai 2024-03-28 19:19 ` (subset) " Vinod Koul 7 siblings, 0 replies; 10+ messages in thread From: Adam Ford @ 2024-02-27 22:04 UTC (permalink / raw) To: linux-arm-kernel, linux-phy Cc: aford, Adam Ford, Luca Ceresoli, Vinod Koul, Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, Lucas Stach, devicetree, imx, linux-kernel The i.MX8M Plus has support for an HDMI transmitter. The video is genereated by lcdif3, routed to the hdmi parallel video interface, then fed to a DW HDMI bridge to support up to 4K video output. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> --- V7: No Change V6: No Change V5: Added Review and tested-by from Luca No functional change since V1 --- arch/arm64/configs/defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 34681284043f..ee644d27652b 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -887,6 +887,7 @@ CONFIG_DRM_ANALOGIX_ANX7625=m CONFIG_DRM_I2C_ADV7511=m CONFIG_DRM_I2C_ADV7511_AUDIO=y CONFIG_DRM_CDNS_MHDP8546=m +CONFIG_DRM_IMX8MP_DW_HDMI_BRIDGE=m CONFIG_DRM_DW_HDMI_AHB_AUDIO=m CONFIG_DRM_DW_HDMI_CEC=m CONFIG_DRM_IMX_DCSS=m -- 2.43.0 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI 2024-02-27 22:04 [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Adam Ford ` (5 preceding siblings ...) 2024-02-27 22:04 ` [PATCH V7 6/6] arm64: defconfig: Enable DRM_IMX8MP_DW_HDMI_BRIDGE as module Adam Ford @ 2024-03-26 9:13 ` Tommaso Merciai 2024-03-28 19:19 ` (subset) " Vinod Koul 7 siblings, 0 replies; 10+ messages in thread From: Tommaso Merciai @ 2024-03-26 9:13 UTC (permalink / raw) To: Adam Ford Cc: linux-arm-kernel, linux-phy, aford, Vinod Koul, Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, Lucas Stach, devicetree, imx, linux-kernel Hi Adam, Thanks for your work. For all the series: Tested-by: Tommaso Merciai <tomm.merciai@gmail.com> Regards, Tommaso On Tue, Feb 27, 2024 at 04:04:34PM -0600, Adam Ford wrote: > The i.MX8M Plus has an HDMI controller, which depends on several > other systems. The Parallel Video Interface (PVI) and the > HDMI-TX are already in the Linux-Next staging area 20240209, but > the HDMI PHY driver and several device trees updates are still needed. > > This series is adapted from multiple series from Lucas Stach with > edits and suggestions from feedback from various attempts, but it > since it's difficult to use and test them independently, > I merged them into on unified series. The version history is a > bit ambiguous since different components were submitted at different > times and had different amount of attempts. > > The previous attempt I did used the wrong starting point for the PHY, > so this update includes a newer starting point with tags from that version > and fixes from various people's feedback. I hope I caught them all, but > I apologize if I missed something. Any tags from the previous attempt I > made were intentionally dropped, because of the significant change, > but I kept tags from the newer version I grabbed from patchwork. > > Because several items from the last attempt were merged, this > series is only focussed on adding the HDMI PHY driver, and enabling > the power domain, irqsteer interrupt controller, and HDMI pipeline > in the device tree. The version numbers are a bit strange since > these all got pulled from various attempts with different versions, > but I wanted to push them together as a series to complete the pending > work. > > This series restarted at V4 based on the version of the PHY driver and > the other drivers and power-domain changes have been applied already. > > V7: Patch 5/7 marks the PVI driver disabled by default to prevent > EPROBE_DEFER errors. > > No other changes to other patches in the series > > V6: Make the PHY driver depend on COMMON_CLK to fix build errors > Make LCDIF3 disabled by default since it depends on hardware. > > V5 primarily updates feedback from the PHY driver itself, but a small > adjustment was made to the register size in the device tree. > Adam Ford (1): > arm64: defconfig: Enable DRM_IMX8MP_DW_HDMI_BRIDGE as module > > > Adam Ford (1): > arm64: defconfig: Enable DRM_IMX8MP_DW_HDMI_BRIDGE as module > > Lucas Stach (5): > dt-bindings: phy: add binding for the i.MX8MP HDMI PHY > phy: freescale: add Samsung HDMI PHY > arm64: dts: imx8mp: add HDMI power-domains > arm64: dts: imx8mp: add HDMI irqsteer > arm64: dts: imx8mp: add HDMI display pipeline > > .../bindings/phy/fsl,imx8mp-hdmi-phy.yaml | 62 ++ > arch/arm64/boot/dts/freescale/imx8mp.dtsi | 147 ++++ > arch/arm64/configs/defconfig | 1 + > drivers/phy/freescale/Kconfig | 6 + > drivers/phy/freescale/Makefile | 1 + > drivers/phy/freescale/phy-fsl-samsung-hdmi.c | 720 ++++++++++++++++++ > 6 files changed, 937 insertions(+) > create mode 100644 Documentation/devicetree/bindings/phy/fsl,imx8mp-hdmi-phy.yaml > create mode 100644 drivers/phy/freescale/phy-fsl-samsung-hdmi.c > > -- > 2.43.0 > > ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: (subset) [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI 2024-02-27 22:04 [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Adam Ford ` (6 preceding siblings ...) 2024-03-26 9:13 ` [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Tommaso Merciai @ 2024-03-28 19:19 ` Vinod Koul 7 siblings, 0 replies; 10+ messages in thread From: Vinod Koul @ 2024-03-28 19:19 UTC (permalink / raw) To: linux-arm-kernel, linux-phy, Adam Ford Cc: aford, Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, Lucas Stach, devicetree, imx, linux-kernel On Tue, 27 Feb 2024 16:04:34 -0600, Adam Ford wrote: > The i.MX8M Plus has an HDMI controller, which depends on several > other systems. The Parallel Video Interface (PVI) and the > HDMI-TX are already in the Linux-Next staging area 20240209, but > the HDMI PHY driver and several device trees updates are still needed. > > This series is adapted from multiple series from Lucas Stach with > edits and suggestions from feedback from various attempts, but it > since it's difficult to use and test them independently, > I merged them into on unified series. The version history is a > bit ambiguous since different components were submitted at different > times and had different amount of attempts. > > [...] Applied, thanks! [1/6] dt-bindings: phy: add binding for the i.MX8MP HDMI PHY commit: d0f4b70eb9a9ed05a37d963655698906cd4dac9a [2/6] phy: freescale: add Samsung HDMI PHY commit: 6ad082bee9025fa8e0ef8ee478c5a614b9db9e3d Best regards, -- ~Vinod ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2024-03-29 3:19 UTC | newest] Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2024-02-27 22:04 [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Adam Ford 2024-02-27 22:04 ` [PATCH V7 1/6] dt-bindings: phy: add binding for the i.MX8MP HDMI PHY Adam Ford 2024-02-27 22:04 ` [PATCH V7 2/6] phy: freescale: add Samsung " Adam Ford 2024-02-27 22:04 ` [PATCH V7 3/6] arm64: dts: imx8mp: add HDMI power-domains Adam Ford 2024-03-29 3:19 ` Shawn Guo 2024-02-27 22:04 ` [PATCH V7 4/6] arm64: dts: imx8mp: add HDMI irqsteer Adam Ford 2024-02-27 22:04 ` [PATCH V7 5/6] arm64: dts: imx8mp: add HDMI display pipeline Adam Ford 2024-02-27 22:04 ` [PATCH V7 6/6] arm64: defconfig: Enable DRM_IMX8MP_DW_HDMI_BRIDGE as module Adam Ford 2024-03-26 9:13 ` [PATCH V7 0/6] soc: imx8mp: Finish support for HDMI Tommaso Merciai 2024-03-28 19:19 ` (subset) " Vinod Koul
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).