[PATCH v3 00/13] PCI: brcmstb: enable PCIe for STB chips

[PATCH v3 00/13] PCI: brcmstb: enable PCIe for STB chips

[Jim Quinlan]

v3:
  Commit "device core: Introduce multiple dma pfn offsets"
  Commit "arm: dma-mapping: Invoke dma offset func if needed"
  -- The above two commits have been squashed.  More importantly,
     the code has been modified so that the functionality for
     multiple pfn offsets subsumes the use of dev->dma_pfn_offset.
     In fact, dma_pfn_offset is removed and supplanted by
     dma_pfn_offset_map, which is a pointer to an array.  The
     more common case of a uniform offset is now handled as
     a map with a single entry, while cases requiring multiple
     pfn offsets use a map with multiple entries.  Code paths
     that used to do this:

         dev->dma_pfn_offset = mydrivers_pfn_offset;

     have been changed to do this:

         attach_uniform_dma_pfn_offset(dev, pfn_offset);

  Commit "dt-bindings: PCI: Add bindings for more Brcmstb chips"
  -- Add if/then clause for required props: resets, reset-names (RobH)
  -- Change compatible list from const to enum (RobH)
  -- Change list of u32-tuples to u64 (RobH)

  Commit "of: Include a dev param in of_dma_get_range()"
  -- modify of/unittests.c to add NULL param in of_dma_get_range() call.

  Commit "device core: Add ability to handle multiple dma offsets"
  -- align comment in device.h (AndyS).
  -- s/cpu_beg/cpu_start/ and s/dma_beg/dma_start/ in struct
     dma_pfn_offset_region (AndyS).

v2:
Commit: "device core: Add ability to handle multiple dma offsets"
  o Added helper func attach_dma_pfn_offset_map() in address.c (Chistoph)
  o Helpers funcs added to __phys_to_dma() & __dma_to_phys() (Christoph)
  o Added warning when multiple offsets are needed and !DMA_PFN_OFFSET_MAP
  o dev->dma_pfn_map => dev->dma_pfn_offset_map
  o s/frm/from/ for dma_pfn_offset_frm_{phys,dma}_addr() (Christoph)
  o In device.h: s/const void */const struct dma_pfn_offset_region */
  o removed 'unlikely' from unlikely(dev->dma_pfn_offset_map) since
    guarded by CONFIG_DMA_PFN_OFFSET_MAP (Christoph)
  o Since dev->dma_pfn_offset is copied in usb/core/{usb,message}.c, now
    dev->dma_pfn_offset_map is copied as well.
  o Merged two of the DMA commits into one (Christoph).

Commit "arm: dma-mapping: Invoke dma offset func if needed":
  o Use helper functions instead of #if CONFIG_DMA_PFN_OFFSET

Other commits' changes:
  o Removed need for carrying of_id var in priv (Nicolas)
  o Commit message rewordings (Bjorn)
  o Commit log messages filled to 75 chars (Bjorn)
  o devm_reset_control_get_shared())
    => devm_reset_control_get_optional_shared (Philipp)
  o Add call to reset_control_assert() in PCIe remove routines (Philipp)

v1:
This patchset expands the usefulness of the Broadcom Settop Box PCIe
controller by building upon the PCIe driver used currently by the
Raspbery Pi.  Other forms of this patchset were submitted by me years
ago and not accepted; the major sticking point was the code required
for the DMA remapping needed for the PCIe driver to work [1].

There have been many changes to the DMA and OF subsystems since that
time, making a cleaner and less intrusive patchset possible.  This
patchset implements a generalization of "dev->dma_pfn_offset", except
that instead of a single scalar offset it provides for multiple
offsets via a function which depends upon the "dma-ranges" property of
the PCIe host controller.  This is required for proper functionality
of the BrcmSTB PCIe controller and possibly some other devices.

[1] https://lore.kernel.org/linux-arm-kernel/1516058925-46522-5-git-send-email-jim2101024@gmail.com/

Jim Quinlan (13):
  PCI: brcmstb: PCIE_BRCMSTB depends on ARCH_BRCMSTB
  ata: ahci_brcm: Fix use of BCM7216 reset controller
  dt-bindings: PCI: Add bindings for more Brcmstb chips
  PCI: brcmstb: Add bcm7278 reigister info
  PCI: brcmstb: Add suspend and resume pm_ops
  PCI: brcmstb: Add bcm7278 PERST support
  PCI: brcmstb: Add control of rescal reset
  of: Include a dev param in of_dma_get_range()
  device core: Introduce multiple dma pfn offsets
  PCI: brcmstb: Set internal memory viewport sizes
  PCI: brcmstb: Accommodate MSI for older chips
  PCI: brcmstb: Set bus max burst size by chip type
  PCI: brcmstb: Add bcm7211, bcm7216, bcm7445, bcm7278 to match list

 .../bindings/pci/brcm,stb-pcie.yaml           |  58 ++-
 arch/arm/include/asm/dma-mapping.h            |   9 +-
 arch/arm/mach-keystone/keystone.c             |   9 +-
 arch/sh/drivers/pci/pcie-sh7786.c             |   3 +-
 arch/sh/kernel/dma-coherent.c                 |  17 +-
 arch/x86/pci/sta2x11-fixup.c                  |   7 +-
 drivers/acpi/arm64/iort.c                     |   5 +-
 drivers/ata/ahci_brcm.c                       |  14 +-
 drivers/gpu/drm/sun4i/sun4i_backend.c         |   7 +-
 drivers/iommu/io-pgtable-arm.c                |   2 +-
 .../platform/sunxi/sun4i-csi/sun4i_csi.c      |   5 +-
 .../platform/sunxi/sun6i-csi/sun6i_csi.c      |   5 +-
 drivers/of/address.c                          |  97 ++++-
 drivers/of/device.c                           |  10 +-
 drivers/of/of_private.h                       |   8 +-
 drivers/of/unittest.c                         |   2 +-
 drivers/pci/controller/Kconfig                |   3 +-
 drivers/pci/controller/pcie-brcmstb.c         | 408 +++++++++++++++---
 drivers/remoteproc/remoteproc_core.c          |   2 +-
 .../staging/media/sunxi/cedrus/cedrus_hw.c    |   7 +-
 drivers/usb/core/message.c                    |   4 +-
 drivers/usb/core/usb.c                        |   2 +-
 include/linux/device.h                        |   4 +-
 include/linux/dma-direct.h                    |  16 +-
 include/linux/dma-mapping.h                   |  45 ++
 kernel/dma/coherent.c                         |  11 +-
 26 files changed, 631 insertions(+), 129 deletions(-)

-- 
2.17.1

[PATCH v3 01/13] PCI: brcmstb: PCIE_BRCMSTB depends on ARCH_BRCMSTB

[Jim Quinlan]

From: Jim Quinlan <jquinlan@broadcom.com>

Have PCIE_BRCMSTB depend on ARCH_BRCMSTB.  Also set the default value to
ARCH_BRCMSTB.

Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 drivers/pci/controller/Kconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
index 91bfdb784829..c0f3d4d10047 100644
--- a/drivers/pci/controller/Kconfig
+++ b/drivers/pci/controller/Kconfig
@@ -244,9 +244,10 @@ config VMD
 
 config PCIE_BRCMSTB
 	tristate "Broadcom Brcmstb PCIe host controller"
-	depends on ARCH_BCM2835 || COMPILE_TEST
+	depends on ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST
 	depends on OF
 	depends on PCI_MSI_IRQ_DOMAIN
+	default ARCH_BRCMSTB
 	help
 	  Say Y here to enable PCIe host controller support for
 	  Broadcom STB based SoCs, like the Raspberry Pi 4.
-- 
2.17.1

[PATCH v3 02/13] ata: ahci_brcm: Fix use of BCM7216 reset controller

[Jim Quinlan]

From: Jim Quinlan <jquinlan@broadcom.com>

A reset controller "rescal" is shared between the AHCI driver and the PCIe
driver for the BrcmSTB 7216 chip.  The code is modified to allow this
sharing and to deassert() properly.

Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>

Fixes: 272ecd60a636 ("ata: ahci_brcm: BCM7216 reset is self de-asserting")
Fixes: c345ec6a50e9 ("ata: ahci_brcm: Support BCM7216 reset controller
name")
---
 drivers/ata/ahci_brcm.c | 14 +++++---------
 1 file changed, 5 insertions(+), 9 deletions(-)

diff --git a/drivers/ata/ahci_brcm.c b/drivers/ata/ahci_brcm.c
index 6853dbb4131d..c4ea555573dd 100644
--- a/drivers/ata/ahci_brcm.c
+++ b/drivers/ata/ahci_brcm.c
@@ -428,7 +428,6 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *of_id;
 	struct device *dev = &pdev->dev;
-	const char *reset_name = NULL;
 	struct brcm_ahci_priv *priv;
 	struct ahci_host_priv *hpriv;
 	struct resource *res;
@@ -452,11 +451,11 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 
 	/* Reset is optional depending on platform and named differently */
 	if (priv->version == BRCM_SATA_BCM7216)
-		reset_name = "rescal";
+		priv->rcdev = devm_reset_control_get_optional_shared(&pdev->dev,
+								     "rescal");
 	else
-		reset_name = "ahci";
-
-	priv->rcdev = devm_reset_control_get_optional(&pdev->dev, reset_name);
+		priv->rcdev = devm_reset_control_get_optional(&pdev->dev,
+							      "ahci");
 	if (IS_ERR(priv->rcdev))
 		return PTR_ERR(priv->rcdev);
 
@@ -479,10 +478,7 @@ static int brcm_ahci_probe(struct platform_device *pdev)
 		break;
 	}
 
-	if (priv->version == BRCM_SATA_BCM7216)
-		ret = reset_control_reset(priv->rcdev);
-	else
-		ret = reset_control_deassert(priv->rcdev);
+	ret = reset_control_deassert(priv->rcdev);
 	if (ret)
 		return ret;
 
-- 
2.17.1

[PATCH v3 03/13] dt-bindings: PCI: Add bindings for more Brcmstb chips

[Jim Quinlan]

From: Jim Quinlan <jquinlan@broadcom.com>

- Add compatible strings for three more Broadcom STB chips: 7278, 7216,
  7211 (STB version of RPi4).
- add new property 'brcm,scb-sizes'
- add new property 'resets'
- add new property 'reset-names' for 7216 only
- allow 'ranges' and 'dma-ranges' to have more than one item and update
  the example to show this.

Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
---
 .../bindings/pci/brcm,stb-pcie.yaml           | 58 ++++++++++++++++---
 1 file changed, 51 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml b/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
index 8680a0f86c5a..4a012d77513f 100644
--- a/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
@@ -9,12 +9,15 @@ title: Brcmstb PCIe Host Controller Device Tree Bindings
 maintainers:
   - Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
 
-allOf:
-  - $ref: /schemas/pci/pci-bus.yaml#
-
 properties:
   compatible:
-    const: brcm,bcm2711-pcie # The Raspberry Pi 4
+    items:
+      - enum:
+          - brcm,bcm2711-pcie # The Raspberry Pi 4
+          - brcm,bcm7211-pcie # Broadcom STB version of RPi4
+          - brcm,bcm7278-pcie # Broadcom 7278 Arm
+          - brcm,bcm7216-pcie # Broadcom 7216 Arm
+          - brcm,bcm7445-pcie # Broadcom 7445 Arm
 
   reg:
     maxItems: 1
@@ -34,10 +37,12 @@ properties:
       - const: msi
 
   ranges:
-    maxItems: 1
+    minItems: 1
+    maxItems: 4
 
   dma-ranges:
-    maxItems: 1
+    minItems: 1
+    maxItems: 6
 
   clocks:
     maxItems: 1
@@ -58,8 +63,33 @@ properties:
 
   aspm-no-l0s: true
 
+  resets:
+    description: for "brcm,bcm7216-pcie", must be a valid reset
+      phandle pointing to the RESCAL reset controller provider node.
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+
+  reset-names:
+    items:
+      - const: rescal
+
+  brcm,scb-sizes:
+    description: u64 giving the 64bit PCIe memory
+      viewport size of a memory controller.  There may be up to
+      three controllers, and each size must be a power of two
+      with a size greater or equal to the amount of memory the
+      controller supports.  Note that each memory controller
+      may have two component regions -- base and extended -- so
+      this information cannot be deduced from the dma-ranges.
+
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint64-array
+      - items:
+          minItems: 1
+          maxItems: 3
+
 required:
   - reg
+  - ranges
   - dma-ranges
   - "#interrupt-cells"
   - interrupts
@@ -68,6 +98,18 @@ required:
   - interrupt-map
   - msi-controller
 
+allOf:
+  - $ref: /schemas/pci/pci-bus.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: brcm,bcm7216-pcie
+    then:
+      required:
+        - resets
+        - reset-names
+
 unevaluatedProperties: false
 
 examples:
@@ -93,7 +135,9 @@ examples:
                     msi-parent = <&pcie0>;
                     msi-controller;
                     ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000 0x0 0x04000000>;
-                    dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 0x0 0x80000000>;
+                    dma-ranges = <0x42000000 0x1 0x00000000 0x0 0x40000000 0x0 0x80000000>,
+                                 <0x42000000 0x1 0x80000000 0x3 0x00000000 0x0 0x80000000>;
                     brcm,enable-ssc;
+                    brcm,scb-sizes =  <0x0000000080000000 0x0000000080000000>;
             };
     };
-- 
2.17.1

[PATCH v3 04/13] PCI: brcmstb: Add bcm7278 reigister info

[Jim Quinlan]

From: Jim Quinlan <jquinlan@broadcom.com>

Add in compatibility strings and code for three Broadcom STB chips.  Some
of the register locations, shifts, and masks are different for certain
chips, requiring the use of different constants based on of_id.

We would like to add the following at this time to the match list but we
need to wait until the end of this patchset so that everything works.

    { .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
    { .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
    { .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
    { .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },

Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
---
 drivers/pci/controller/pcie-brcmstb.c | 108 +++++++++++++++++++++++---
 1 file changed, 96 insertions(+), 12 deletions(-)

diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 73020b4ff090..7c707e483181 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -120,9 +120,8 @@
 #define  PCIE_EXT_SLOT_SHIFT				15
 #define  PCIE_EXT_FUNC_SHIFT				12
 
-#define PCIE_RGR1_SW_INIT_1				0x9210
 #define  PCIE_RGR1_SW_INIT_1_PERST_MASK			0x1
-#define  PCIE_RGR1_SW_INIT_1_INIT_MASK			0x2
+#define  PCIE_RGR1_SW_INIT_1_PERST_SHIFT		0x0
 
 /* PCIe parameters */
 #define BRCM_NUM_PCIE_OUT_WINS		0x4
@@ -152,6 +151,76 @@
 #define SSC_STATUS_SSC_MASK		0x400
 #define SSC_STATUS_PLL_LOCK_MASK	0x800
 
+#define IDX_ADDR(pcie)	\
+	(pcie->reg_offsets[EXT_CFG_INDEX])
+#define DATA_ADDR(pcie)	\
+	(pcie->reg_offsets[EXT_CFG_DATA])
+#define PCIE_RGR1_SW_INIT_1(pcie) \
+	(pcie->reg_offsets[RGR1_SW_INIT_1])
+
+enum {
+	RGR1_SW_INIT_1,
+	EXT_CFG_INDEX,
+	EXT_CFG_DATA,
+};
+
+enum {
+	RGR1_SW_INIT_1_INIT_MASK,
+	RGR1_SW_INIT_1_INIT_SHIFT,
+};
+
+enum pcie_type {
+	GENERIC,
+	BCM7278,
+	BCM2711,
+};
+
+struct pcie_cfg_data {
+	const int *reg_field_info;
+	const int *offsets;
+	const enum pcie_type type;
+};
+
+static const int pcie_reg_field_info[] = {
+	[RGR1_SW_INIT_1_INIT_MASK] = 0x2,
+	[RGR1_SW_INIT_1_INIT_SHIFT] = 0x1,
+};
+
+static const int pcie_reg_field_info_bcm7278[] = {
+	[RGR1_SW_INIT_1_INIT_MASK] = 0x1,
+	[RGR1_SW_INIT_1_INIT_SHIFT] = 0x0,
+};
+
+static const int pcie_offsets[] = {
+	[RGR1_SW_INIT_1] = 0x9210,
+	[EXT_CFG_INDEX]  = 0x9000,
+	[EXT_CFG_DATA]   = 0x9004,
+};
+
+static const struct pcie_cfg_data generic_cfg = {
+	.reg_field_info	= pcie_reg_field_info,
+	.offsets	= pcie_offsets,
+	.type		= GENERIC,
+};
+
+static const int pcie_offset_bcm7278[] = {
+	[RGR1_SW_INIT_1] = 0xc010,
+	[EXT_CFG_INDEX] = 0x9000,
+	[EXT_CFG_DATA] = 0x9004,
+};
+
+static const struct pcie_cfg_data bcm7278_cfg = {
+	.reg_field_info = pcie_reg_field_info_bcm7278,
+	.offsets	= pcie_offset_bcm7278,
+	.type		= BCM7278,
+};
+
+static const struct pcie_cfg_data bcm2711_cfg = {
+	.reg_field_info	= pcie_reg_field_info,
+	.offsets	= pcie_offsets,
+	.type		= BCM2711,
+};
+
 struct brcm_msi {
 	struct device		*dev;
 	void __iomem		*base;
@@ -176,6 +245,9 @@ struct brcm_pcie {
 	int			gen;
 	u64			msi_target_addr;
 	struct brcm_msi		*msi;
+	const int		*reg_offsets;
+	const int		*reg_field_info;
+	enum pcie_type		type;
 };
 
 /*
@@ -602,20 +674,21 @@ static struct pci_ops brcm_pcie_ops = {
 
 static inline void brcm_pcie_bridge_sw_init_set(struct brcm_pcie *pcie, u32 val)
 {
-	u32 tmp;
+	u32 tmp, mask =  pcie->reg_field_info[RGR1_SW_INIT_1_INIT_MASK];
+	u32 shift = pcie->reg_field_info[RGR1_SW_INIT_1_INIT_SHIFT];
 
-	tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1);
-	u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_INIT_MASK);
-	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1);
+	tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+	tmp = (tmp & ~mask) | ((val << shift) & mask);
+	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
 }
 
 static inline void brcm_pcie_perst_set(struct brcm_pcie *pcie, u32 val)
 {
 	u32 tmp;
 
-	tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1);
+	tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
 	u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK);
-	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1);
+	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
 }
 
 static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
@@ -924,10 +997,16 @@ static int brcm_pcie_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct of_device_id brcm_pcie_match[] = {
+	{ .compatible = "brcm,bcm2711-pcie", .data = &bcm2711_cfg },
+	{},
+};
+
 static int brcm_pcie_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node, *msi_np;
 	struct pci_host_bridge *bridge;
+	const struct pcie_cfg_data *data;
 	struct brcm_pcie *pcie;
 	struct pci_bus *child;
 	struct resource *res;
@@ -937,9 +1016,18 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 	if (!bridge)
 		return -ENOMEM;
 
+	data = of_device_get_match_data(&pdev->dev);
+	if (!data) {
+		pr_err("failed to look up compatible string\n");
+		return -EINVAL;
+	}
+
 	pcie = pci_host_bridge_priv(bridge);
 	pcie->dev = &pdev->dev;
 	pcie->np = np;
+	pcie->reg_offsets = data->offsets;
+	pcie->reg_field_info = data->reg_field_info;
+	pcie->type = data->type;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	pcie->base = devm_ioremap_resource(&pdev->dev, res);
@@ -1005,10 +1093,6 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 	return ret;
 }
 
-static const struct of_device_id brcm_pcie_match[] = {
-	{ .compatible = "brcm,bcm2711-pcie" },
-	{},
-};
 MODULE_DEVICE_TABLE(of, brcm_pcie_match);
 
 static struct platform_driver brcm_pcie_driver = {
-- 
2.17.1

[PATCH v3 05/13] PCI: brcmstb: Add suspend and resume pm_ops

[Jim Quinlan]

From: Jim Quinlan <jquinlan@broadcom.com>

Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend
and resume.  Now the PCIe driver may do so as well.

Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
---
 drivers/pci/controller/pcie-brcmstb.c | 49 +++++++++++++++++++++++++++
 1 file changed, 49 insertions(+)

diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 7c707e483181..f444751e247c 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -979,6 +979,49 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
 	brcm_pcie_bridge_sw_init_set(pcie, 1);
 }
 
+static int brcm_pcie_suspend(struct device *dev)
+{
+	struct brcm_pcie *pcie = dev_get_drvdata(dev);
+	int ret = 0;
+
+	brcm_pcie_turn_off(pcie);
+	clk_disable_unprepare(pcie->clk);
+
+	return ret;
+}
+
+static int brcm_pcie_resume(struct device *dev)
+{
+	struct brcm_pcie *pcie = dev_get_drvdata(dev);
+	void __iomem *base;
+	u32 tmp;
+	int ret;
+
+	base = pcie->base;
+	clk_prepare_enable(pcie->clk);
+
+	/* Take bridge out of reset so we can access the SERDES reg */
+	brcm_pcie_bridge_sw_init_set(pcie, 0);
+
+	/* SERDES_IDDQ = 0 */
+	tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
+	u32p_replace_bits(&tmp, 0,
+			  PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK);
+	writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
+
+	/* wait for serdes to be stable */
+	udelay(100);
+
+	ret = brcm_pcie_setup(pcie);
+	if (ret)
+		return ret;
+
+	if (pcie->msi)
+		brcm_msi_set_regs(pcie->msi);
+
+	return 0;
+}
+
 static void __brcm_pcie_remove(struct brcm_pcie *pcie)
 {
 	brcm_msi_remove(pcie);
@@ -1095,12 +1138,18 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 
 MODULE_DEVICE_TABLE(of, brcm_pcie_match);
 
+static const struct dev_pm_ops brcm_pcie_pm_ops = {
+	.suspend_noirq = brcm_pcie_suspend,
+	.resume_noirq = brcm_pcie_resume,
+};
+
 static struct platform_driver brcm_pcie_driver = {
 	.probe = brcm_pcie_probe,
 	.remove = brcm_pcie_remove,
 	.driver = {
 		.name = "brcm-pcie",
 		.of_match_table = brcm_pcie_match,
+		.pm = &brcm_pcie_pm_ops,
 	},
 };
 module_platform_driver(brcm_pcie_driver);
-- 
2.17.1

[PATCH v3 06/13] PCI: brcmstb: Add bcm7278 PERST support

[Jim Quinlan]

From: Jim Quinlan <jquinlan@broadcom.com>

The PERST bit was moved to a different register in 7278-type STB chips.  In
addition, the polarity of the bit was also changed; for other chips writing
a 1 specified assert; for 7278-type chips, writing a 0 specifies assert.

Signal-wise, PERST is an asserted-low signal.

Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
---
 drivers/pci/controller/pcie-brcmstb.c | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index f444751e247c..0bcae9eba048 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -81,6 +81,7 @@
 
 #define PCIE_MISC_PCIE_CTRL				0x4064
 #define  PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK	0x1
+#define PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK		0x4
 
 #define PCIE_MISC_PCIE_STATUS				0x4068
 #define  PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK		0x80
@@ -686,9 +687,17 @@ static inline void brcm_pcie_perst_set(struct brcm_pcie *pcie, u32 val)
 {
 	u32 tmp;
 
-	tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
-	u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK);
-	writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+	if (pcie->type == BCM7278) {
+		/* Perst bit has moved and assert value is 0 */
+		tmp = readl(pcie->base + PCIE_MISC_PCIE_CTRL);
+		u32p_replace_bits(&tmp,
+				  !val, PCIE_MISC_PCIE_CTRL_PCIE_PERSTB_MASK);
+		writel(tmp, pcie->base +  PCIE_MISC_PCIE_CTRL);
+	} else {
+		tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+		u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK);
+		writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1(pcie));
+	}
 }
 
 static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
-- 
2.17.1

[PATCH v3 07/13] PCI: brcmstb: Add control of rescal reset

[Jim Quinlan]

From: Jim Quinlan <jquinlan@broadcom.com>

Some STB chips have a special purpose reset controller named RESCAL (reset
calibration).  The PCIe HW can now control RESCAL to start and stop its
operation.

Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
---
 drivers/pci/controller/pcie-brcmstb.c | 81 ++++++++++++++++++++++++++-
 1 file changed, 80 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 0bcae9eba048..fa356bc149c3 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -23,6 +23,7 @@
 #include <linux/of_platform.h>
 #include <linux/pci.h>
 #include <linux/printk.h>
+#include <linux/reset.h>
 #include <linux/sizes.h>
 #include <linux/slab.h>
 #include <linux/string.h>
@@ -152,7 +153,17 @@
 #define SSC_STATUS_SSC_MASK		0x400
 #define SSC_STATUS_PLL_LOCK_MASK	0x800
 
-#define IDX_ADDR(pcie)	\
+/* Rescal registers */
+#define PCIE_DVT_PMU_PCIE_PHY_CTRL				0xc700
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS			0x3
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_MASK		0x4
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_SHIFT	0x2
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_MASK		0x2
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_SHIFT		0x1
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_MASK		0x1
+#define  PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_SHIFT		0x0
+
+#define IDX_ADDR(pcie) \
 	(pcie->reg_offsets[EXT_CFG_INDEX])
 #define DATA_ADDR(pcie)	\
 	(pcie->reg_offsets[EXT_CFG_DATA])
@@ -249,6 +260,7 @@ struct brcm_pcie {
 	const int		*reg_offsets;
 	const int		*reg_field_info;
 	enum pcie_type		type;
+	struct reset_control	*rescal;
 };
 
 /*
@@ -964,6 +976,47 @@ static void brcm_pcie_enter_l23(struct brcm_pcie *pcie)
 		dev_err(pcie->dev, "failed to enter low-power link state\n");
 }
 
+static int brcm_phy_cntl(struct brcm_pcie *pcie, const int start)
+{
+	static const u32 shifts[PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS] = {
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_SHIFT,
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_SHIFT,
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_SHIFT,};
+	static const u32 masks[PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS] = {
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_PWRDN_MASK,
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_RESET_MASK,
+		PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_DIG_RESET_MASK,};
+	const int beg = start ? 0 : PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS - 1;
+	const int end = start ? PCIE_DVT_PMU_PCIE_PHY_CTRL_DAST_NFLDS : -1;
+	u32 tmp, combined_mask = 0;
+	u32 val = !!start;
+	void __iomem *base = pcie->base;
+	int i;
+
+	for (i = beg; i != end; start ? i++ : i--) {
+		tmp = readl(base + PCIE_DVT_PMU_PCIE_PHY_CTRL);
+		tmp = (tmp & ~masks[i]) | ((val << shifts[i]) & masks[i]);
+		writel(tmp, base + PCIE_DVT_PMU_PCIE_PHY_CTRL);
+		usleep_range(50, 200);
+		combined_mask |= masks[i];
+	}
+
+	tmp = readl(base + PCIE_DVT_PMU_PCIE_PHY_CTRL);
+	val = start ? combined_mask : 0;
+
+	return (tmp & combined_mask) == val ? 0 : -EIO;
+}
+
+static inline int brcm_phy_start(struct brcm_pcie *pcie)
+{
+	return pcie->rescal ? brcm_phy_cntl(pcie, 1) : 0;
+}
+
+static inline int brcm_phy_stop(struct brcm_pcie *pcie)
+{
+	return pcie->rescal ? brcm_phy_cntl(pcie, 0) : 0;
+}
+
 static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
 {
 	void __iomem *base = pcie->base;
@@ -994,6 +1047,9 @@ static int brcm_pcie_suspend(struct device *dev)
 	int ret = 0;
 
 	brcm_pcie_turn_off(pcie);
+	ret = brcm_phy_stop(pcie);
+	if (ret)
+		dev_err(pcie->dev, "failed to stop phy\n");
 	clk_disable_unprepare(pcie->clk);
 
 	return ret;
@@ -1009,6 +1065,12 @@ static int brcm_pcie_resume(struct device *dev)
 	base = pcie->base;
 	clk_prepare_enable(pcie->clk);
 
+	ret = brcm_phy_start(pcie);
+	if (ret) {
+		dev_err(pcie->dev, "failed to start phy\n");
+		return ret;
+	}
+
 	/* Take bridge out of reset so we can access the SERDES reg */
 	brcm_pcie_bridge_sw_init_set(pcie, 0);
 
@@ -1035,6 +1097,9 @@ static void __brcm_pcie_remove(struct brcm_pcie *pcie)
 {
 	brcm_msi_remove(pcie);
 	brcm_pcie_turn_off(pcie);
+	if (brcm_phy_stop(pcie))
+		dev_err(pcie->dev, "failed to stop phy\n");
+	reset_control_assert(pcie->rescal);
 	clk_disable_unprepare(pcie->clk);
 }
 
@@ -1105,6 +1170,20 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "could not enable clock\n");
 		return ret;
 	}
+	pcie->rescal = devm_reset_control_get_optional_shared(&pdev->dev,
+							      "rescal");
+	if (IS_ERR(pcie->rescal))
+		return PTR_ERR(pcie->rescal);
+
+	ret = reset_control_deassert(pcie->rescal);
+	if (ret)
+		dev_err(&pdev->dev, "failed to deassert 'rescal'\n");
+
+	ret = brcm_phy_start(pcie);
+	if (ret) {
+		dev_err(pcie->dev, "failed to start phy\n");
+		return ret;
+	}
 
 	ret = brcm_pcie_setup(pcie);
 	if (ret)
-- 
2.17.1

[PATCH v3 08/13] of: Include a dev param in of_dma_get_range()

[Jim Quinlan]

Currently there is only one caller of of_dma_get_range().  A struct device
*dev param is needed For implementing multiple dma offsets.  This function
will still work if dev == NULL.

Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
---
 drivers/of/address.c    | 4 +++-
 drivers/of/device.c     | 2 +-
 drivers/of/of_private.h | 8 ++++----
 drivers/of/unittest.c   | 2 +-
 4 files changed, 9 insertions(+), 7 deletions(-)

diff --git a/drivers/of/address.c b/drivers/of/address.c
index 8eea3f6e29a4..96d8cfb14a60 100644
--- a/drivers/of/address.c
+++ b/drivers/of/address.c
@@ -920,6 +920,7 @@ EXPORT_SYMBOL(of_io_request_and_map);
 
 /**
  * of_dma_get_range - Get DMA range info
+ * @dev:	device pointer; only needed for a corner case.
  * @np:		device node to get DMA range info
  * @dma_addr:	pointer to store initial DMA address of DMA range
  * @paddr:	pointer to store initial CPU address of DMA range
@@ -935,7 +936,8 @@ EXPORT_SYMBOL(of_io_request_and_map);
  * It returns -ENODEV if "dma-ranges" property was not found
  * for this device in DT.
  */
-int of_dma_get_range(struct device_node *np, u64 *dma_addr, u64 *paddr, u64 *size)
+int of_dma_get_range(struct device *dev, struct device_node *np, u64 *dma_addr,
+		     u64 *paddr, u64 *size)
 {
 	struct device_node *node = of_node_get(np);
 	const __be32 *ranges = NULL;
diff --git a/drivers/of/device.c b/drivers/of/device.c
index 27203bfd0b22..ef6a741f9f0b 100644
--- a/drivers/of/device.c
+++ b/drivers/of/device.c
@@ -95,7 +95,7 @@ int of_dma_configure(struct device *dev, struct device_node *np, bool force_dma)
 	const struct iommu_ops *iommu;
 	u64 mask, end;
 
-	ret = of_dma_get_range(np, &dma_addr, &paddr, &size);
+	ret = of_dma_get_range(dev, np, &dma_addr, &paddr, &size);
 	if (ret < 0) {
 		/*
 		 * For legacy reasons, we have to assume some devices need
diff --git a/drivers/of/of_private.h b/drivers/of/of_private.h
index edc682249c00..7a83d3a81ab6 100644
--- a/drivers/of/of_private.h
+++ b/drivers/of/of_private.h
@@ -158,11 +158,11 @@ extern int of_bus_n_addr_cells(struct device_node *np);
 extern int of_bus_n_size_cells(struct device_node *np);
 
 #ifdef CONFIG_OF_ADDRESS
-extern int of_dma_get_range(struct device_node *np, u64 *dma_addr,
-			    u64 *paddr, u64 *size);
+extern int of_dma_get_range(struct device *dev, struct device_node *np,
+			    u64 *dma_addr, u64 *paddr, u64 *size);
 #else
-static inline int of_dma_get_range(struct device_node *np, u64 *dma_addr,
-				   u64 *paddr, u64 *size)
+static inline int of_dma_get_range(struct device *dev, struct device_node *np,
+				   u64 *dma_addr, u64 *paddr, u64 *size)
 {
 	return -ENODEV;
 }
diff --git a/drivers/of/unittest.c b/drivers/of/unittest.c
index 398de04fd19c..57a22517c428 100644
--- a/drivers/of/unittest.c
+++ b/drivers/of/unittest.c
@@ -881,7 +881,7 @@ static void __init of_unittest_dma_ranges_one(const char *path,
 		return;
 	}
 
-	rc = of_dma_get_range(np, &dma_addr, &paddr, &size);
+	rc = of_dma_get_range(NULL, np, &dma_addr, &paddr, &size);
 
 	unittest(!rc, "of_dma_get_range failed on node %pOF rc=%i\n", np, rc);
 	if (!rc) {
-- 
2.17.1

[PATCH v3 10/13] PCI: brcmstb: Set internal memory viewport sizes

[Jim Quinlan]

BrcmSTB PCIe controllers are intimately connected to the memory
controller(s) on the SOC.  There is a "viewport" for each memory controller
that allows inbound accesses to CPU memory.  Each viewport's size must be
set to a power of two, and that size must be equal to or larger than the
amount of memory each controller supports.

Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
---
 drivers/pci/controller/pcie-brcmstb.c | 67 ++++++++++++++++++++-------
 1 file changed, 49 insertions(+), 18 deletions(-)

diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index fa356bc149c3..338e9ed44230 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -55,6 +55,8 @@
 #define  PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK	0x300000
 #define  PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128		0x0
 #define  PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK		0xf8000000
+#define  PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK		0x07c00000
+#define  PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK		0x0000001f
 
 #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO		0x400c
 #define PCIE_MEM_WIN0_LO(win)	\
@@ -152,6 +154,7 @@
 #define SSC_STATUS_OFFSET		0x1
 #define SSC_STATUS_SSC_MASK		0x400
 #define SSC_STATUS_PLL_LOCK_MASK	0x800
+#define PCIE_BRCM_MAX_MEMC		3
 
 /* Rescal registers */
 #define PCIE_DVT_PMU_PCIE_PHY_CTRL				0xc700
@@ -261,6 +264,8 @@ struct brcm_pcie {
 	const int		*reg_field_info;
 	enum pcie_type		type;
 	struct reset_control	*rescal;
+	int			num_memc;
+	u64			memc_size[PCIE_BRCM_MAX_MEMC];
 };
 
 /*
@@ -717,22 +722,40 @@ static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
 							u64 *rc_bar2_offset)
 {
 	struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
-	struct device *dev = pcie->dev;
 	struct resource_entry *entry;
+	struct device *dev = pcie->dev;
+	u64 lowest_pcie_addr = ~(u64)0;
+	int ret, i = 0;
+	u64 size = 0;
 
-	entry = resource_list_first_type(&bridge->dma_ranges, IORESOURCE_MEM);
-	if (!entry)
-		return -ENODEV;
+	resource_list_for_each_entry(entry, &bridge->dma_ranges) {
+		u64 pcie_beg = entry->res->start - entry->offset;
 
+		size += entry->res->end - entry->res->start + 1;
+		if (pcie_beg < lowest_pcie_addr)
+			lowest_pcie_addr = pcie_beg;
+	}
 
-	/*
-	 * The controller expects the inbound window offset to be calculated as
-	 * the difference between PCIe's address space and CPU's. The offset
-	 * provided by the firmware is calculated the opposite way, so we
-	 * negate it.
-	 */
-	*rc_bar2_offset = -entry->offset;
-	*rc_bar2_size = 1ULL << fls64(entry->res->end - entry->res->start);
+	ret = of_property_read_variable_u64_array(
+		pcie->np, "brcm,scb-sizes", pcie->memc_size, 1,
+		PCIE_BRCM_MAX_MEMC);
+
+	if (ret <= 0) {
+		/* Make an educated guess */
+		pcie->num_memc = 1;
+		pcie->memc_size[0] = 1 << fls64(size - 1);
+	} else {
+		pcie->num_memc = ret;
+	}
+
+	/* Each memc is viewed through a "port" that is a power of 2 */
+	for (i = 0, size = 0; i < pcie->num_memc; i++)
+		size += pcie->memc_size[i];
+
+	/* System memory starts at this address in PCIe-space */
+	*rc_bar2_offset = lowest_pcie_addr;
+	/* The sum of all memc views must also be a power of 2 */
+	*rc_bar2_size = 1ULL << fls64(size - 1);
 
 	/*
 	 * We validate the inbound memory view even though we should trust
@@ -784,12 +807,11 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	void __iomem *base = pcie->base;
 	struct device *dev = pcie->dev;
 	struct resource_entry *entry;
-	unsigned int scb_size_val;
 	bool ssc_good = false;
 	struct resource *res;
 	int num_out_wins = 0;
 	u16 nlw, cls, lnksta;
-	int i, ret;
+	int i, ret, memc;
 	u32 tmp, aspm_support;
 
 	/* Reset the bridge */
@@ -825,11 +847,20 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	writel(upper_32_bits(rc_bar2_offset),
 	       base + PCIE_MISC_RC_BAR2_CONFIG_HI);
 
-	scb_size_val = rc_bar2_size ?
-		       ilog2(rc_bar2_size) - 15 : 0xf; /* 0xf is 1GB */
 	tmp = readl(base + PCIE_MISC_MISC_CTRL);
-	u32p_replace_bits(&tmp, scb_size_val,
-			  PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK);
+	for (memc = 0; memc < pcie->num_memc; memc++) {
+		u32 scb_size_val = ilog2(pcie->memc_size[memc]) - 15;
+
+		if (memc == 0)
+			u32p_replace_bits(&tmp, scb_size_val,
+					  PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK);
+		else if (memc == 1)
+			u32p_replace_bits(&tmp, scb_size_val,
+					  PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK);
+		else if (memc == 2)
+			u32p_replace_bits(&tmp, scb_size_val,
+					  PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK);
+	}
 	writel(tmp, base + PCIE_MISC_MISC_CTRL);
 
 	/*
-- 
2.17.1

[PATCH v3 11/13] PCI: brcmstb: Accommodate MSI for older chips

[Jim Quinlan]

From: Jim Quinlan <jquinlan@broadcom.com>

Older BrcmSTB chips do not have a separate register for MSI interrupts; the
MSIs are in a register that also contains unrelated interrupts.  In
addition, the interrupts lie in bits [31..24] for these legacy chips.  This
commit provides common code for both legacy and non-legacy MSI interrupt
registers.

Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
---
 drivers/pci/controller/pcie-brcmstb.c | 72 +++++++++++++++++++--------
 1 file changed, 52 insertions(+), 20 deletions(-)

diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 338e9ed44230..9930419e3ac2 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -80,7 +80,8 @@
 #define PCIE_MISC_MSI_BAR_CONFIG_HI			0x4048
 
 #define PCIE_MISC_MSI_DATA_CONFIG			0x404c
-#define  PCIE_MISC_MSI_DATA_CONFIG_VAL			0xffe06540
+#define  PCIE_MISC_MSI_DATA_CONFIG_VAL_32		0xffe06540
+#define  PCIE_MISC_MSI_DATA_CONFIG_VAL_8		0xfff86540
 
 #define PCIE_MISC_PCIE_CTRL				0x4064
 #define  PCIE_MISC_PCIE_CTRL_PCIE_L23_REQUEST_MASK	0x1
@@ -92,6 +93,9 @@
 #define  PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_MASK	0x10
 #define  PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK	0x40
 
+#define PCIE_MISC_REVISION				0x406c
+#define  BRCM_PCIE_HW_REV_33				0x0303
+
 #define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT		0x4070
 #define  PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK	0xfff00000
 #define  PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK	0xfff0
@@ -112,10 +116,14 @@
 #define  PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK	0x2
 #define  PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK		0x08000000
 
-#define PCIE_MSI_INTR2_STATUS				0x4500
-#define PCIE_MSI_INTR2_CLR				0x4508
-#define PCIE_MSI_INTR2_MASK_SET				0x4510
-#define PCIE_MSI_INTR2_MASK_CLR				0x4514
+
+#define PCIE_INTR2_CPU_BASE		0x4300
+#define PCIE_MSI_INTR2_BASE		0x4500
+/* Offsets from PCIE_INTR2_CPU_BASE and PCIE_MSI_INTR2_BASE */
+#define  MSI_INT_STATUS			0x0
+#define  MSI_INT_CLR			0x8
+#define  MSI_INT_MASK_SET		0x10
+#define  MSI_INT_MASK_CLR		0x14
 
 #define PCIE_EXT_CFG_DATA				0x8000
 
@@ -130,6 +138,8 @@
 /* PCIe parameters */
 #define BRCM_NUM_PCIE_OUT_WINS		0x4
 #define BRCM_INT_PCI_MSI_NR		32
+#define BRCM_INT_PCI_MSI_LEGACY_NR	8
+#define BRCM_INT_PCI_MSI_SHIFT		0
 
 /* MSI target adresses */
 #define BRCM_MSI_TARGET_ADDR_LT_4GB	0x0fffffffcULL
@@ -247,6 +257,12 @@ struct brcm_msi {
 	int			irq;
 	/* used indicates which MSI interrupts have been alloc'd */
 	unsigned long		used;
+	bool			legacy;
+	/* Some chips have MSIs in bits [31..24] of a shared register. */
+	int			legacy_shift;
+	int			nr; /* No. of MSI available, depends on chip */
+	/* This is the base pointer for interrupt status/set/clr regs */
+	void __iomem		*intr_base;
 };
 
 /* Internal PCIe Host Controller Information.*/
@@ -266,6 +282,7 @@ struct brcm_pcie {
 	struct reset_control	*rescal;
 	int			num_memc;
 	u64			memc_size[PCIE_BRCM_MAX_MEMC];
+	u32			hw_rev;
 };
 
 /*
@@ -456,8 +473,10 @@ static void brcm_pcie_msi_isr(struct irq_desc *desc)
 	msi = irq_desc_get_handler_data(desc);
 	dev = msi->dev;
 
-	status = readl(msi->base + PCIE_MSI_INTR2_STATUS);
-	for_each_set_bit(bit, &status, BRCM_INT_PCI_MSI_NR) {
+	status = readl(msi->intr_base + MSI_INT_STATUS);
+	status >>= msi->legacy_shift;
+
+	for_each_set_bit(bit, &status, msi->nr) {
 		virq = irq_find_mapping(msi->inner_domain, bit);
 		if (virq)
 			generic_handle_irq(virq);
@@ -474,7 +493,7 @@ static void brcm_msi_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
 
 	msg->address_lo = lower_32_bits(msi->target_addr);
 	msg->address_hi = upper_32_bits(msi->target_addr);
-	msg->data = (0xffff & PCIE_MISC_MSI_DATA_CONFIG_VAL) | data->hwirq;
+	msg->data = (0xffff & PCIE_MISC_MSI_DATA_CONFIG_VAL_32) | data->hwirq;
 }
 
 static int brcm_msi_set_affinity(struct irq_data *irq_data,
@@ -486,8 +505,9 @@ static int brcm_msi_set_affinity(struct irq_data *irq_data,
 static void brcm_msi_ack_irq(struct irq_data *data)
 {
 	struct brcm_msi *msi = irq_data_get_irq_chip_data(data);
+	const int shift_amt = data->hwirq + msi->legacy_shift;
 
-	writel(1 << data->hwirq, msi->base + PCIE_MSI_INTR2_CLR);
+	writel(1 << shift_amt, msi->intr_base + MSI_INT_CLR);
 }
 
 
@@ -503,7 +523,7 @@ static int brcm_msi_alloc(struct brcm_msi *msi)
 	int hwirq;
 
 	mutex_lock(&msi->lock);
-	hwirq = bitmap_find_free_region(&msi->used, BRCM_INT_PCI_MSI_NR, 0);
+	hwirq = bitmap_find_free_region(&msi->used, msi->nr, 0);
 	mutex_unlock(&msi->lock);
 
 	return hwirq;
@@ -552,7 +572,7 @@ static int brcm_allocate_domains(struct brcm_msi *msi)
 	struct fwnode_handle *fwnode = of_node_to_fwnode(msi->np);
 	struct device *dev = msi->dev;
 
-	msi->inner_domain = irq_domain_add_linear(NULL, BRCM_INT_PCI_MSI_NR,
+	msi->inner_domain = irq_domain_add_linear(NULL, msi->nr,
 						  &msi_domain_ops, msi);
 	if (!msi->inner_domain) {
 		dev_err(dev, "failed to create IRQ domain\n");
@@ -590,7 +610,10 @@ static void brcm_msi_remove(struct brcm_pcie *pcie)
 
 static void brcm_msi_set_regs(struct brcm_msi *msi)
 {
-	writel(0xffffffff, msi->base + PCIE_MSI_INTR2_MASK_CLR);
+	u32 val = __GENMASK(31, msi->legacy_shift);
+
+	writel(val, msi->intr_base + MSI_INT_MASK_CLR);
+	writel(val, msi->intr_base + MSI_INT_CLR);
 
 	/*
 	 * The 0 bit of PCIE_MISC_MSI_BAR_CONFIG_LO is repurposed to MSI
@@ -601,8 +624,10 @@ static void brcm_msi_set_regs(struct brcm_msi *msi)
 	writel(upper_32_bits(msi->target_addr),
 	       msi->base + PCIE_MISC_MSI_BAR_CONFIG_HI);
 
-	writel(PCIE_MISC_MSI_DATA_CONFIG_VAL,
-	       msi->base + PCIE_MISC_MSI_DATA_CONFIG);
+	val = msi->legacy ? PCIE_MISC_MSI_DATA_CONFIG_VAL_8 :
+		PCIE_MISC_MSI_DATA_CONFIG_VAL_32;
+
+	writel(val, msi->base + PCIE_MISC_MSI_DATA_CONFIG);
 }
 
 static int brcm_pcie_enable_msi(struct brcm_pcie *pcie)
@@ -627,6 +652,17 @@ static int brcm_pcie_enable_msi(struct brcm_pcie *pcie)
 	msi->np = pcie->np;
 	msi->target_addr = pcie->msi_target_addr;
 	msi->irq = irq;
+	msi->legacy = pcie->hw_rev < BRCM_PCIE_HW_REV_33;
+
+	if (msi->legacy) {
+		msi->intr_base = msi->base + PCIE_INTR2_CPU_BASE;
+		msi->nr = BRCM_INT_PCI_MSI_LEGACY_NR;
+		msi->legacy_shift = 24;
+	} else {
+		msi->intr_base = msi->base + PCIE_MSI_INTR2_BASE;
+		msi->nr = BRCM_INT_PCI_MSI_NR;
+		msi->legacy_shift = 0;
+	}
 
 	ret = brcm_allocate_domains(msi);
 	if (ret)
@@ -885,12 +921,6 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	tmp &= ~PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK;
 	writel(tmp, base + PCIE_MISC_RC_BAR3_CONFIG_LO);
 
-	/* Mask all interrupts since we are not handling any yet */
-	writel(0xffffffff, pcie->base + PCIE_MSI_INTR2_MASK_SET);
-
-	/* clear any interrupts we find on boot */
-	writel(0xffffffff, pcie->base + PCIE_MSI_INTR2_CLR);
-
 	if (pcie->gen)
 		brcm_pcie_set_gen(pcie, pcie->gen);
 
@@ -1220,6 +1250,8 @@ static int brcm_pcie_probe(struct platform_device *pdev)
 	if (ret)
 		goto fail;
 
+	pcie->hw_rev = readl(pcie->base + PCIE_MISC_REVISION);
+
 	msi_np = of_parse_phandle(pcie->np, "msi-parent", 0);
 	if (pci_msi_enabled() && msi_np == pcie->np) {
 		ret = brcm_pcie_enable_msi(pcie);
-- 
2.17.1

[PATCH v3 12/13] PCI: brcmstb: Set bus max burst size by chip type

[Jim Quinlan]

From: Jim Quinlan <jquinlan@broadcom.com>

The proper value of the parameter SCB_MAX_BURST_SIZE varies per chip.  The
2711 family requires 128B whereas other devices can employ 512.  The
assignment is complicated by the fact that the values for this two-bit
field have different meanings;

  Value   Type_Generic    Type_7278

     00       Reserved         128B
     01           128B         256B
     10           256B         512B
     11           512B     Reserved

Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
---
 drivers/pci/controller/pcie-brcmstb.c | 18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)

diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 9930419e3ac2..131cf0a51398 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -53,7 +53,7 @@
 #define  PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK		0x1000
 #define  PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK	0x2000
 #define  PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK	0x300000
-#define  PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128		0x0
+
 #define  PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK		0xf8000000
 #define  PCIE_MISC_MISC_CTRL_SCB1_SIZE_MASK		0x07c00000
 #define  PCIE_MISC_MISC_CTRL_SCB2_SIZE_MASK		0x0000001f
@@ -848,7 +848,7 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	int num_out_wins = 0;
 	u16 nlw, cls, lnksta;
 	int i, ret, memc;
-	u32 tmp, aspm_support;
+	u32 tmp, burst, aspm_support;
 
 	/* Reset the bridge */
 	brcm_pcie_bridge_sw_init_set(pcie, 1);
@@ -864,10 +864,22 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	/* Wait for SerDes to be stable */
 	usleep_range(100, 200);
 
+	/*
+	 * SCB_MAX_BURST_SIZE is a two bit field.  For GENERIC chips it
+	 * is encoded as 0=128, 1=256, 2=512, 3=Rsvd, for BCM7278 it
+	 * is encoded as 0=Rsvd, 1=128, 2=256, 3=512.
+	 */
+	if (pcie->type == BCM2711)
+		burst = 0x0; /* 128B */
+	else if (pcie->type == BCM7278)
+		burst = 0x3; /* 512 bytes */
+	else
+		burst = 0x2; /* 512 bytes */
+
 	/* Set SCB_MAX_BURST_SIZE, CFG_READ_UR_MODE, SCB_ACCESS_EN */
 	u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK);
 	u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK);
-	u32p_replace_bits(&tmp, PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128,
+	u32p_replace_bits(&tmp, burst,
 			  PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK);
 	writel(tmp, base + PCIE_MISC_MISC_CTRL);
 
-- 
2.17.1

[PATCH v3 13/13] PCI: brcmstb: Add bcm7211, bcm7216, bcm7445, bcm7278 to match list

[Jim Quinlan]

Now that the support is in place with previous commits, we add several
chips that use the BrcmSTB driver.

Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
---
 drivers/pci/controller/pcie-brcmstb.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index 131cf0a51398..22dbecb5403c 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -1189,6 +1189,10 @@ static int brcm_pcie_remove(struct platform_device *pdev)
 
 static const struct of_device_id brcm_pcie_match[] = {
 	{ .compatible = "brcm,bcm2711-pcie", .data = &bcm2711_cfg },
+	{ .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
+	{ .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
+	{ .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
+	{ .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
 	{},
 };
 
-- 
2.17.1

Re: [PATCH v3 13/13] PCI: brcmstb: Add bcm7211, bcm7216, bcm7445, bcm7278 to match list

[Florian Fainelli]

On 6/3/2020 12:20 PM, Jim Quinlan wrote:
> Now that the support is in place with previous commits, we add several
> chips that use the BrcmSTB driver.
> 
> Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>

Acked-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [PATCH v3 12/13] PCI: brcmstb: Set bus max burst size by chip type

[Florian Fainelli]

On 6/3/2020 12:20 PM, Jim Quinlan wrote:
> From: Jim Quinlan <jquinlan@broadcom.com>
> 
> The proper value of the parameter SCB_MAX_BURST_SIZE varies per chip.  The
> 2711 family requires 128B whereas other devices can employ 512.  The
> assignment is complicated by the fact that the values for this two-bit
> field have different meanings;
> 
>   Value   Type_Generic    Type_7278

It looks like Type_Generic and Type_7278 should be swapped in this
description. Other than that:

Acked-by: Florian Fainelli <f.fainelli@gmail.com>

> 
>      00       Reserved         128B
>      01           128B         256B
>      10           256B         512B
>      11           512B     Reserved
-- 
Florian

Re: [PATCH v3 05/13] PCI: brcmstb: Add suspend and resume pm_ops

[Bjorn Helgaas]

On Wed, Jun 03, 2020 at 03:20:37PM -0400, Jim Quinlan wrote:
> From: Jim Quinlan <jquinlan@broadcom.com>
> 
> Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend
> and resume.  Now the PCIe driver may do so as well.
> 
> Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
> ---
>  drivers/pci/controller/pcie-brcmstb.c | 49 +++++++++++++++++++++++++++
>  1 file changed, 49 insertions(+)
> 
> diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
> index 7c707e483181..f444751e247c 100644
> --- a/drivers/pci/controller/pcie-brcmstb.c
> +++ b/drivers/pci/controller/pcie-brcmstb.c
> @@ -979,6 +979,49 @@ static void brcm_pcie_turn_off(struct brcm_pcie *pcie)
>  	brcm_pcie_bridge_sw_init_set(pcie, 1);
>  }
>  
> +static int brcm_pcie_suspend(struct device *dev)
> +{
> +	struct brcm_pcie *pcie = dev_get_drvdata(dev);
> +	int ret = 0;
> +
> +	brcm_pcie_turn_off(pcie);
> +	clk_disable_unprepare(pcie->clk);
> +
> +	return ret;

No need for "ret".

> +}

Re: [PATCH v3 04/13] PCI: brcmstb: Add bcm7278 reigister info

[Florian Fainelli]

On 6/3/2020 12:20 PM, Jim Quinlan wrote:
> From: Jim Quinlan <jquinlan@broadcom.com>
> 
> Add in compatibility strings and code for three Broadcom STB chips.  Some
> of the register locations, shifts, and masks are different for certain
> chips, requiring the use of different constants based on of_id.
> 
> We would like to add the following at this time to the match list but we
> need to wait until the end of this patchset so that everything works.
> 
>     { .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
>     { .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
>     { .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
>     { .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },

If you need to resubmit, there is a typo in the subject: reigister vs.
register. Other than that:

Acked-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [PATCH v3 06/13] PCI: brcmstb: Add bcm7278 PERST support

[Florian Fainelli]

On 6/3/2020 12:20 PM, Jim Quinlan wrote:
> From: Jim Quinlan <jquinlan@broadcom.com>
> 
> The PERST bit was moved to a different register in 7278-type STB chips.  In
> addition, the polarity of the bit was also changed; for other chips writing
> a 1 specified assert; for 7278-type chips, writing a 0 specifies assert.
> 
> Signal-wise, PERST is an asserted-low signal.
> 
> Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>

Acked-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [PATCH v3 07/13] PCI: brcmstb: Add control of rescal reset

[Florian Fainelli]

On 6/3/2020 12:20 PM, Jim Quinlan wrote:
> From: Jim Quinlan <jquinlan@broadcom.com>
> 
> Some STB chips have a special purpose reset controller named RESCAL (reset
> calibration).  The PCIe HW can now control RESCAL to start and stop its
> operation.
> 
> Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>

Acked-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [PATCH v3 10/13] PCI: brcmstb: Set internal memory viewport sizes

[Florian Fainelli]

On 6/3/2020 12:20 PM, Jim Quinlan wrote:
> BrcmSTB PCIe controllers are intimately connected to the memory
> controller(s) on the SOC.  There is a "viewport" for each memory controller
> that allows inbound accesses to CPU memory.  Each viewport's size must be
> set to a power of two, and that size must be equal to or larger than the
> amount of memory each controller supports.
> 
> Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>

Acked-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [PATCH v3 11/13] PCI: brcmstb: Accommodate MSI for older chips

[Florian Fainelli]

On 6/3/2020 12:20 PM, Jim Quinlan wrote:
> From: Jim Quinlan <jquinlan@broadcom.com>
> 
> Older BrcmSTB chips do not have a separate register for MSI interrupts; the
> MSIs are in a register that also contains unrelated interrupts.  In
> addition, the interrupts lie in bits [31..24] for these legacy chips.  This
> commit provides common code for both legacy and non-legacy MSI interrupt
> registers.
> 
> Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>

Acked-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [PATCH v3 02/13] ata: ahci_brcm: Fix use of BCM7216 reset controller

[Florian Fainelli]

On 6/3/2020 12:20 PM, Jim Quinlan wrote:
> From: Jim Quinlan <jquinlan@broadcom.com>
> 
> A reset controller "rescal" is shared between the AHCI driver and the PCIe
> driver for the BrcmSTB 7216 chip.  The code is modified to allow this
> sharing and to deassert() properly.
> 
> Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
> 
> Fixes: 272ecd60a636 ("ata: ahci_brcm: BCM7216 reset is self de-asserting")
> Fixes: c345ec6a50e9 ("ata: ahci_brcm: Support BCM7216 reset controller
> name")
> ---

[snip]

> @@ -479,10 +478,7 @@ static int brcm_ahci_probe(struct platform_device *pdev)
>  		break;
>  	}
>  
> -	if (priv->version == BRCM_SATA_BCM7216)
> -		ret = reset_control_reset(priv->rcdev);
> -	else
> -		ret = reset_control_deassert(priv->rcdev);
> +	ret = reset_control_deassert(priv->rcdev);
>  	if (ret)
>  		return ret;

Do we need a similar change for brcm_ahci_resume()?
-- 
Florian