[PATCH v2 0/4] regulator: add MP8867/MP8869 support

[PATCH v2 0/4] regulator: add MP8867/MP8869 support

[Jisheng Zhang]

From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>

The MP8867/MP8869 from Monolithic Power Systems is a single output
DC/DC converter. The voltage can be controlled via I2C.

since v1:
  - rebase on regulator for-next branch

Jisheng Zhang (4):
  regulator: bindings: add MPS mp8869 voltage regulator
  regulator: add support for MP8869 regulator
  dt-bindings: mp886x: Document MP8867 support
  regulator: mp886x: add MP8867 support

 .../devicetree/bindings/regulator/mp886x.txt  |  27 ++
 drivers/regulator/Kconfig                     |   7 +
 drivers/regulator/Makefile                    |   1 +
 drivers/regulator/mp886x.c                    | 290 ++++++++++++++++++
 4 files changed, 325 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/mp886x.txt
 create mode 100644 drivers/regulator/mp886x.c

-- 
2.24.0

[PATCH v2 1/4] regulator: bindings: add MPS mp8869 voltage regulator

[Jisheng Zhang]

From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>

The MP8869 from Monolithic Power Systems is a single output dc/dc
converter with voltage control over i2c.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
---
 .../devicetree/bindings/regulator/mp886x.txt  | 25 +++++++++++++++++++
 1 file changed, 25 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/mp886x.txt

diff --git a/Documentation/devicetree/bindings/regulator/mp886x.txt b/Documentation/devicetree/bindings/regulator/mp886x.txt
new file mode 100644
index 000000000000..6858e38eb47d
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/mp886x.txt
@@ -0,0 +1,25 @@
+Monolithic Power Systems MP8869 voltage regulator
+
+Required properties:
+- compatible: "mps,mp8869";
+- reg: I2C slave address.
+- enable-gpios: enable gpios.
+- mps,fb-voltage-divider: An array of two integers containing the resistor
+  values R1 and R2 of the feedback voltage divider in kilo ohms.
+
+Any property defined as part of the core regulator binding, defined in
+./regulator.txt, can also be used.
+
+Example:
+
+	vcpu: regulator@62 {
+		compatible = "mps,mp8869";
+		regulator-name = "vcpu";
+		regulator-min-microvolt = <700000>;
+		regulator-max-microvolt = <850000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-gpios = <&porta 1 GPIO_ACTIVE_LOW>;
+		mps,fb-voltage-divider = <80 240>;
+		reg = <0x62>;
+	};
-- 
2.24.0

[PATCH v2 2/4] regulator: add support for MP8869 regulator

[Jisheng Zhang]

From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>

The MP8869 from Monolithic Power Systems is a single output DC/DC
converter. The voltage can be controlled via I2C.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
---
 drivers/regulator/Kconfig  |   7 ++
 drivers/regulator/Makefile |   1 +
 drivers/regulator/mp886x.c | 230 +++++++++++++++++++++++++++++++++++++
 3 files changed, 238 insertions(+)
 create mode 100644 drivers/regulator/mp886x.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 64a39f34ef37..f4b72cb098ef 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -635,6 +635,13 @@ config REGULATOR_MP8859
 	  Say M here if you want to include support for the regulator as a
 	  module. The module will be named "mp8859".
 
+config REGULATOR_MP886X
+	tristate "MPS MP8869 regulator driver"
+	depends on I2C && (OF || COMPILE_TEST)
+	select REGMAP_I2C
+	help
+	  This driver supports the MP8869 voltage regulator.
+
 config REGULATOR_MPQ7920
 	tristate "Monolithic MPQ7920 PMIC"
 	depends on I2C && OF
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index bc69d6481646..6610ee001d9a 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -80,6 +80,7 @@ obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o
 obj-$(CONFIG_REGULATOR_MCP16502) += mcp16502.o
 obj-$(CONFIG_REGULATOR_MP5416) += mp5416.o
 obj-$(CONFIG_REGULATOR_MP8859) += mp8859.o
+obj-$(CONFIG_REGULATOR_MP886X) += mp886x.o
 obj-$(CONFIG_REGULATOR_MPQ7920) += mpq7920.o
 obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
 obj-$(CONFIG_REGULATOR_MT6323)	+= mt6323-regulator.o
diff --git a/drivers/regulator/mp886x.c b/drivers/regulator/mp886x.c
new file mode 100644
index 000000000000..f77321a449ca
--- /dev/null
+++ b/drivers/regulator/mp886x.c
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// MP8869 regulator driver
+//
+// Copyright (C) 2020 Synaptics Incorporated
+//
+// Author: Jisheng Zhang <jszhang@kernel.org>
+
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+#define MP886X_VSEL		0x00
+#define  MP886X_V_BOOT		(1 << 7)
+#define MP886X_SYSCNTLREG1	0x01
+#define  MP886X_MODE		(1 << 0)
+#define  MP886X_GO		(1 << 6)
+#define  MP886X_EN		(1 << 7)
+
+struct mp886x_device_info {
+	struct device *dev;
+	struct regulator_desc desc;
+	struct regulator_init_data *regulator;
+	struct gpio_desc *en_gpio;
+	u32 r[2];
+	unsigned int sel;
+};
+
+static int mp886x_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	switch (mode) {
+	case REGULATOR_MODE_FAST:
+		regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
+				   MP886X_MODE, MP886X_MODE);
+		break;
+	case REGULATOR_MODE_NORMAL:
+		regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
+				   MP886X_MODE, 0);
+		break;
+	default:
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static unsigned int mp886x_get_mode(struct regulator_dev *rdev)
+{
+	u32 val;
+	int ret;
+
+	ret = regmap_read(rdev->regmap, MP886X_SYSCNTLREG1, &val);
+	if (ret < 0)
+		return ret;
+	if (val & MP886X_MODE)
+		return REGULATOR_MODE_FAST;
+	else
+		return REGULATOR_MODE_NORMAL;
+}
+
+static int mp8869_set_voltage_sel(struct regulator_dev *rdev, unsigned int sel)
+{
+	int ret;
+
+	ret = regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
+				 MP886X_GO, MP886X_GO);
+	if (ret < 0)
+		return ret;
+
+	sel <<= ffs(rdev->desc->vsel_mask) - 1;
+	return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
+				  MP886X_V_BOOT | rdev->desc->vsel_mask, sel);
+}
+
+static inline unsigned int mp8869_scale(unsigned int uv, u32 r1, u32 r2)
+{
+	u32 tmp = uv * r1 / r2;
+
+	return uv + tmp;
+}
+
+static int mp8869_get_voltage_sel(struct regulator_dev *rdev)
+{
+	struct mp886x_device_info *di = rdev_get_drvdata(rdev);
+	int ret, uv;
+	unsigned int val;
+	bool fbloop;
+
+	ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
+	if (ret)
+		return ret;
+
+	fbloop = val & MP886X_V_BOOT;
+	if (fbloop) {
+		uv = rdev->desc->min_uV;
+		uv = mp8869_scale(uv, di->r[0], di->r[1]);
+		return regulator_map_voltage_linear(rdev, uv, uv);
+	}
+
+	val &= rdev->desc->vsel_mask;
+	val >>= ffs(rdev->desc->vsel_mask) - 1;
+
+	return val;
+}
+
+static const struct regulator_ops mp8869_regulator_ops = {
+	.set_voltage_sel = mp8869_set_voltage_sel,
+	.get_voltage_sel = mp8869_get_voltage_sel,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.map_voltage = regulator_map_voltage_linear,
+	.list_voltage = regulator_list_voltage_linear,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_mode = mp886x_set_mode,
+	.get_mode = mp886x_get_mode,
+};
+
+static int mp886x_regulator_register(struct mp886x_device_info *di,
+				     struct regulator_config *config)
+{
+	struct regulator_desc *rdesc = &di->desc;
+	struct regulator_dev *rdev;
+
+	rdesc->name = "mp886x-reg";
+	rdesc->supply_name = "vin";
+	rdesc->ops = of_device_get_match_data(di->dev);
+	rdesc->type = REGULATOR_VOLTAGE;
+	rdesc->n_voltages = 128;
+	rdesc->enable_reg = MP886X_SYSCNTLREG1;
+	rdesc->enable_mask = MP886X_EN;
+	rdesc->min_uV = 600000;
+	rdesc->uV_step = 10000;
+	rdesc->vsel_reg = MP886X_VSEL;
+	rdesc->vsel_mask = 0x3f;
+	rdesc->owner = THIS_MODULE;
+
+	rdev = devm_regulator_register(di->dev, &di->desc, config);
+	if (IS_ERR(rdev))
+		return PTR_ERR(rdev);
+	di->sel = rdesc->ops->get_voltage_sel(rdev);
+	return 0;
+}
+
+static const struct regmap_config mp886x_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+};
+
+static int mp886x_i2c_probe(struct i2c_client *client,
+			    const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct device_node *np = dev->of_node;
+	struct mp886x_device_info *di;
+	struct regulator_config config = { };
+	struct regmap *regmap;
+	int ret;
+
+	di = devm_kzalloc(dev, sizeof(struct mp886x_device_info), GFP_KERNEL);
+	if (!di)
+		return -ENOMEM;
+
+	di->regulator = of_get_regulator_init_data(dev, np, &di->desc);
+	if (!di->regulator) {
+		dev_err(dev, "Platform data not found!\n");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32_array(np, "mps,fb-voltage-divider",
+					 di->r, 2);
+	if (ret)
+		return ret;
+
+	di->en_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_HIGH);
+	if (IS_ERR(di->en_gpio))
+		return PTR_ERR(di->en_gpio);
+
+	di->dev = dev;
+
+	regmap = devm_regmap_init_i2c(client, &mp886x_regmap_config);
+	if (IS_ERR(regmap)) {
+		dev_err(dev, "Failed to allocate regmap!\n");
+		return PTR_ERR(regmap);
+	}
+	i2c_set_clientdata(client, di);
+
+	config.dev = di->dev;
+	config.init_data = di->regulator;
+	config.regmap = regmap;
+	config.driver_data = di;
+	config.of_node = np;
+
+	ret = mp886x_regulator_register(di, &config);
+	if (ret < 0)
+		dev_err(dev, "Failed to register regulator!\n");
+	return ret;
+}
+
+static const struct of_device_id mp886x_dt_ids[] = {
+	{
+		.compatible = "mps,mp8869",
+		.data = &mp8869_regulator_ops
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, mp886x_dt_ids);
+
+static const struct i2c_device_id mp886x_id[] = {
+	{ "mp886x", },
+	{ },
+};
+MODULE_DEVICE_TABLE(i2c, mp886x_id);
+
+static struct i2c_driver mp886x_regulator_driver = {
+	.driver = {
+		.name = "mp886x-regulator",
+		.of_match_table = of_match_ptr(mp886x_dt_ids),
+	},
+	.probe = mp886x_i2c_probe,
+	.id_table = mp886x_id,
+};
+module_i2c_driver(mp886x_regulator_driver);
+
+MODULE_AUTHOR("Jisheng Zhang <jszhang@kernel.org>");
+MODULE_DESCRIPTION("MP886x regulator driver");
+MODULE_LICENSE("GPL v2");
-- 
2.24.0

[PATCH v2 3/4] dt-bindings: mp886x: Document MP8867 support

[Jisheng Zhang]

From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>

MP8867 is an I2C-controlled adjustable voltage regulator made by
Monolithic Power Systems. The difference between MP8867 and MP8869
are:
1.If V_BOOT, the vref of MP8869 is fixed at 600mv while vref of MP8867
is determined by the I2C control.
2.For MP8867, when setting voltage, if the steps is within 5, we need
to manually set the GO_BIT to 0.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
---
 Documentation/devicetree/bindings/regulator/mp886x.txt | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/mp886x.txt b/Documentation/devicetree/bindings/regulator/mp886x.txt
index 6858e38eb47d..551867829459 100644
--- a/Documentation/devicetree/bindings/regulator/mp886x.txt
+++ b/Documentation/devicetree/bindings/regulator/mp886x.txt
@@ -1,7 +1,9 @@
-Monolithic Power Systems MP8869 voltage regulator
+Monolithic Power Systems MP8867/MP8869 voltage regulator
 
 Required properties:
-- compatible: "mps,mp8869";
+- compatible: Must be one of the following.
+	"mps,mp8867"
+	"mps,mp8869"
 - reg: I2C slave address.
 - enable-gpios: enable gpios.
 - mps,fb-voltage-divider: An array of two integers containing the resistor
-- 
2.24.0

[PATCH v2 4/4] regulator: mp886x: add MP8867 support

[Jisheng Zhang]

From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>

MP8867 is an I2C-controlled adjustable voltage regulator made by
Monolithic Power Systems. The difference between MP8867 and MP8869
are:
1.If V_BOOT, the vref of MP8869 is fixed at 600mv while vref of
MP8867 is determined by the I2C control.
2.For MP8867, when setting voltage, if the step is within 5, we
need to manually set the GO BIT to 0.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
---
 drivers/regulator/mp886x.c | 62 +++++++++++++++++++++++++++++++++++++-
 1 file changed, 61 insertions(+), 1 deletion(-)

diff --git a/drivers/regulator/mp886x.c b/drivers/regulator/mp886x.c
index f77321a449ca..1786f7162019 100644
--- a/drivers/regulator/mp886x.c
+++ b/drivers/regulator/mp886x.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 //
-// MP8869 regulator driver
+// MP8867/MP8869 regulator driver
 //
 // Copyright (C) 2020 Synaptics Incorporated
 //
@@ -119,6 +119,62 @@ static const struct regulator_ops mp8869_regulator_ops = {
 	.get_mode = mp886x_get_mode,
 };
 
+static int mp8867_set_voltage_sel(struct regulator_dev *rdev, unsigned int sel)
+{
+	struct mp886x_device_info *di = rdev_get_drvdata(rdev);
+	int ret, delta;
+
+	ret = mp8869_set_voltage_sel(rdev, sel);
+	if (ret < 0)
+		return ret;
+
+	delta = di->sel - sel;
+	if (abs(delta) <= 5)
+		ret = regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
+					 MP886X_GO, 0);
+	di->sel = sel;
+
+	return ret;
+}
+
+static int mp8867_get_voltage_sel(struct regulator_dev *rdev)
+{
+	struct mp886x_device_info *di = rdev_get_drvdata(rdev);
+	int ret, uv;
+	unsigned int val;
+	bool fbloop;
+
+	ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
+	if (ret)
+		return ret;
+
+	fbloop = val & MP886X_V_BOOT;
+
+	val &= rdev->desc->vsel_mask;
+	val >>= ffs(rdev->desc->vsel_mask) - 1;
+
+	if (fbloop) {
+		uv = regulator_list_voltage_linear(rdev, val);
+		uv = mp8869_scale(uv, di->r[0], di->r[1]);
+		return regulator_map_voltage_linear(rdev, uv, uv);
+	}
+
+	return val;
+}
+
+static const struct regulator_ops mp8867_regulator_ops = {
+	.set_voltage_sel = mp8867_set_voltage_sel,
+	.get_voltage_sel = mp8867_get_voltage_sel,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.map_voltage = regulator_map_voltage_linear,
+	.list_voltage = regulator_list_voltage_linear,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_mode = mp886x_set_mode,
+	.get_mode = mp886x_get_mode,
+};
+
 static int mp886x_regulator_register(struct mp886x_device_info *di,
 				     struct regulator_config *config)
 {
@@ -201,6 +257,10 @@ static int mp886x_i2c_probe(struct i2c_client *client,
 }
 
 static const struct of_device_id mp886x_dt_ids[] = {
+	{
+		.compatible = "mps,mp8867",
+		.data = &mp8867_regulator_ops
+	},
 	{
 		.compatible = "mps,mp8869",
 		.data = &mp8869_regulator_ops
-- 
2.24.0

Applied "regulator: mp886x: Document MP8867 support" to the regulator tree

[Mark Brown]

The patch

   regulator: mp886x: Document MP8867 support

has been applied to the regulator tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From b11dec18e6334da2f2a11e07cf43e2a394b12c06 Mon Sep 17 00:00:00 2001
From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Date: Mon, 16 Mar 2020 22:31:00 +0800
Subject: [PATCH] regulator: mp886x: Document MP8867 support

MP8867 is an I2C-controlled adjustable voltage regulator made by
Monolithic Power Systems. The difference between MP8867 and MP8869
are:
1.If V_BOOT, the vref of MP8869 is fixed at 600mv while vref of MP8867
is determined by the I2C control.
2.For MP8867, when setting voltage, if the steps is within 5, we need
to manually set the GO_BIT to 0.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316223100.37805b22@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 Documentation/devicetree/bindings/regulator/mp886x.txt | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/regulator/mp886x.txt b/Documentation/devicetree/bindings/regulator/mp886x.txt
index 6858e38eb47d..551867829459 100644
--- a/Documentation/devicetree/bindings/regulator/mp886x.txt
+++ b/Documentation/devicetree/bindings/regulator/mp886x.txt
@@ -1,7 +1,9 @@
-Monolithic Power Systems MP8869 voltage regulator
+Monolithic Power Systems MP8867/MP8869 voltage regulator
 
 Required properties:
-- compatible: "mps,mp8869";
+- compatible: Must be one of the following.
+	"mps,mp8867"
+	"mps,mp8869"
 - reg: I2C slave address.
 - enable-gpios: enable gpios.
 - mps,fb-voltage-divider: An array of two integers containing the resistor
-- 
2.20.1

Applied "regulator: mp886x: add MP8867 support" to the regulator tree

[Mark Brown]

The patch

   regulator: mp886x: add MP8867 support

has been applied to the regulator tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From 751ca3aa15be815373536eb8b3dc44910b800e9f Mon Sep 17 00:00:00 2001
From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Date: Mon, 16 Mar 2020 22:31:27 +0800
Subject: [PATCH] regulator: mp886x: add MP8867 support

MP8867 is an I2C-controlled adjustable voltage regulator made by
Monolithic Power Systems. The difference between MP8867 and MP8869
are:
1.If V_BOOT, the vref of MP8869 is fixed at 600mv while vref of
MP8867 is determined by the I2C control.
2.For MP8867, when setting voltage, if the step is within 5, we
need to manually set the GO BIT to 0.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316223127.4b1ecc92@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/mp886x.c | 62 +++++++++++++++++++++++++++++++++++++-
 1 file changed, 61 insertions(+), 1 deletion(-)

diff --git a/drivers/regulator/mp886x.c b/drivers/regulator/mp886x.c
index f77321a449ca..1786f7162019 100644
--- a/drivers/regulator/mp886x.c
+++ b/drivers/regulator/mp886x.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 //
-// MP8869 regulator driver
+// MP8867/MP8869 regulator driver
 //
 // Copyright (C) 2020 Synaptics Incorporated
 //
@@ -119,6 +119,62 @@ static const struct regulator_ops mp8869_regulator_ops = {
 	.get_mode = mp886x_get_mode,
 };
 
+static int mp8867_set_voltage_sel(struct regulator_dev *rdev, unsigned int sel)
+{
+	struct mp886x_device_info *di = rdev_get_drvdata(rdev);
+	int ret, delta;
+
+	ret = mp8869_set_voltage_sel(rdev, sel);
+	if (ret < 0)
+		return ret;
+
+	delta = di->sel - sel;
+	if (abs(delta) <= 5)
+		ret = regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
+					 MP886X_GO, 0);
+	di->sel = sel;
+
+	return ret;
+}
+
+static int mp8867_get_voltage_sel(struct regulator_dev *rdev)
+{
+	struct mp886x_device_info *di = rdev_get_drvdata(rdev);
+	int ret, uv;
+	unsigned int val;
+	bool fbloop;
+
+	ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
+	if (ret)
+		return ret;
+
+	fbloop = val & MP886X_V_BOOT;
+
+	val &= rdev->desc->vsel_mask;
+	val >>= ffs(rdev->desc->vsel_mask) - 1;
+
+	if (fbloop) {
+		uv = regulator_list_voltage_linear(rdev, val);
+		uv = mp8869_scale(uv, di->r[0], di->r[1]);
+		return regulator_map_voltage_linear(rdev, uv, uv);
+	}
+
+	return val;
+}
+
+static const struct regulator_ops mp8867_regulator_ops = {
+	.set_voltage_sel = mp8867_set_voltage_sel,
+	.get_voltage_sel = mp8867_get_voltage_sel,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.map_voltage = regulator_map_voltage_linear,
+	.list_voltage = regulator_list_voltage_linear,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_mode = mp886x_set_mode,
+	.get_mode = mp886x_get_mode,
+};
+
 static int mp886x_regulator_register(struct mp886x_device_info *di,
 				     struct regulator_config *config)
 {
@@ -201,6 +257,10 @@ static int mp886x_i2c_probe(struct i2c_client *client,
 }
 
 static const struct of_device_id mp886x_dt_ids[] = {
+	{
+		.compatible = "mps,mp8867",
+		.data = &mp8867_regulator_ops
+	},
 	{
 		.compatible = "mps,mp8869",
 		.data = &mp8869_regulator_ops
-- 
2.20.1

Applied "regulator: add support for MP8869 regulator" to the regulator tree

[Mark Brown]

The patch

   regulator: add support for MP8869 regulator

has been applied to the regulator tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From 97be82880b617fb6bc06ff19e3ddb039501b2dcf Mon Sep 17 00:00:00 2001
From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Date: Mon, 16 Mar 2020 22:30:20 +0800
Subject: [PATCH] regulator: add support for MP8869 regulator

The MP8869 from Monolithic Power Systems is a single output DC/DC
converter. The voltage can be controlled via I2C.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316223020.1a6d92ae@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/Kconfig  |   7 ++
 drivers/regulator/Makefile |   1 +
 drivers/regulator/mp886x.c | 230 +++++++++++++++++++++++++++++++++++++
 3 files changed, 238 insertions(+)
 create mode 100644 drivers/regulator/mp886x.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 64a39f34ef37..f4b72cb098ef 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -635,6 +635,13 @@ config REGULATOR_MP8859
 	  Say M here if you want to include support for the regulator as a
 	  module. The module will be named "mp8859".
 
+config REGULATOR_MP886X
+	tristate "MPS MP8869 regulator driver"
+	depends on I2C && (OF || COMPILE_TEST)
+	select REGMAP_I2C
+	help
+	  This driver supports the MP8869 voltage regulator.
+
 config REGULATOR_MPQ7920
 	tristate "Monolithic MPQ7920 PMIC"
 	depends on I2C && OF
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index bc69d6481646..6610ee001d9a 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -80,6 +80,7 @@ obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o
 obj-$(CONFIG_REGULATOR_MCP16502) += mcp16502.o
 obj-$(CONFIG_REGULATOR_MP5416) += mp5416.o
 obj-$(CONFIG_REGULATOR_MP8859) += mp8859.o
+obj-$(CONFIG_REGULATOR_MP886X) += mp886x.o
 obj-$(CONFIG_REGULATOR_MPQ7920) += mpq7920.o
 obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
 obj-$(CONFIG_REGULATOR_MT6323)	+= mt6323-regulator.o
diff --git a/drivers/regulator/mp886x.c b/drivers/regulator/mp886x.c
new file mode 100644
index 000000000000..f77321a449ca
--- /dev/null
+++ b/drivers/regulator/mp886x.c
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// MP8869 regulator driver
+//
+// Copyright (C) 2020 Synaptics Incorporated
+//
+// Author: Jisheng Zhang <jszhang@kernel.org>
+
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+#define MP886X_VSEL		0x00
+#define  MP886X_V_BOOT		(1 << 7)
+#define MP886X_SYSCNTLREG1	0x01
+#define  MP886X_MODE		(1 << 0)
+#define  MP886X_GO		(1 << 6)
+#define  MP886X_EN		(1 << 7)
+
+struct mp886x_device_info {
+	struct device *dev;
+	struct regulator_desc desc;
+	struct regulator_init_data *regulator;
+	struct gpio_desc *en_gpio;
+	u32 r[2];
+	unsigned int sel;
+};
+
+static int mp886x_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	switch (mode) {
+	case REGULATOR_MODE_FAST:
+		regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
+				   MP886X_MODE, MP886X_MODE);
+		break;
+	case REGULATOR_MODE_NORMAL:
+		regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
+				   MP886X_MODE, 0);
+		break;
+	default:
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static unsigned int mp886x_get_mode(struct regulator_dev *rdev)
+{
+	u32 val;
+	int ret;
+
+	ret = regmap_read(rdev->regmap, MP886X_SYSCNTLREG1, &val);
+	if (ret < 0)
+		return ret;
+	if (val & MP886X_MODE)
+		return REGULATOR_MODE_FAST;
+	else
+		return REGULATOR_MODE_NORMAL;
+}
+
+static int mp8869_set_voltage_sel(struct regulator_dev *rdev, unsigned int sel)
+{
+	int ret;
+
+	ret = regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
+				 MP886X_GO, MP886X_GO);
+	if (ret < 0)
+		return ret;
+
+	sel <<= ffs(rdev->desc->vsel_mask) - 1;
+	return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
+				  MP886X_V_BOOT | rdev->desc->vsel_mask, sel);
+}
+
+static inline unsigned int mp8869_scale(unsigned int uv, u32 r1, u32 r2)
+{
+	u32 tmp = uv * r1 / r2;
+
+	return uv + tmp;
+}
+
+static int mp8869_get_voltage_sel(struct regulator_dev *rdev)
+{
+	struct mp886x_device_info *di = rdev_get_drvdata(rdev);
+	int ret, uv;
+	unsigned int val;
+	bool fbloop;
+
+	ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
+	if (ret)
+		return ret;
+
+	fbloop = val & MP886X_V_BOOT;
+	if (fbloop) {
+		uv = rdev->desc->min_uV;
+		uv = mp8869_scale(uv, di->r[0], di->r[1]);
+		return regulator_map_voltage_linear(rdev, uv, uv);
+	}
+
+	val &= rdev->desc->vsel_mask;
+	val >>= ffs(rdev->desc->vsel_mask) - 1;
+
+	return val;
+}
+
+static const struct regulator_ops mp8869_regulator_ops = {
+	.set_voltage_sel = mp8869_set_voltage_sel,
+	.get_voltage_sel = mp8869_get_voltage_sel,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.map_voltage = regulator_map_voltage_linear,
+	.list_voltage = regulator_list_voltage_linear,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_mode = mp886x_set_mode,
+	.get_mode = mp886x_get_mode,
+};
+
+static int mp886x_regulator_register(struct mp886x_device_info *di,
+				     struct regulator_config *config)
+{
+	struct regulator_desc *rdesc = &di->desc;
+	struct regulator_dev *rdev;
+
+	rdesc->name = "mp886x-reg";
+	rdesc->supply_name = "vin";
+	rdesc->ops = of_device_get_match_data(di->dev);
+	rdesc->type = REGULATOR_VOLTAGE;
+	rdesc->n_voltages = 128;
+	rdesc->enable_reg = MP886X_SYSCNTLREG1;
+	rdesc->enable_mask = MP886X_EN;
+	rdesc->min_uV = 600000;
+	rdesc->uV_step = 10000;
+	rdesc->vsel_reg = MP886X_VSEL;
+	rdesc->vsel_mask = 0x3f;
+	rdesc->owner = THIS_MODULE;
+
+	rdev = devm_regulator_register(di->dev, &di->desc, config);
+	if (IS_ERR(rdev))
+		return PTR_ERR(rdev);
+	di->sel = rdesc->ops->get_voltage_sel(rdev);
+	return 0;
+}
+
+static const struct regmap_config mp886x_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+};
+
+static int mp886x_i2c_probe(struct i2c_client *client,
+			    const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct device_node *np = dev->of_node;
+	struct mp886x_device_info *di;
+	struct regulator_config config = { };
+	struct regmap *regmap;
+	int ret;
+
+	di = devm_kzalloc(dev, sizeof(struct mp886x_device_info), GFP_KERNEL);
+	if (!di)
+		return -ENOMEM;
+
+	di->regulator = of_get_regulator_init_data(dev, np, &di->desc);
+	if (!di->regulator) {
+		dev_err(dev, "Platform data not found!\n");
+		return -EINVAL;
+	}
+
+	ret = of_property_read_u32_array(np, "mps,fb-voltage-divider",
+					 di->r, 2);
+	if (ret)
+		return ret;
+
+	di->en_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_HIGH);
+	if (IS_ERR(di->en_gpio))
+		return PTR_ERR(di->en_gpio);
+
+	di->dev = dev;
+
+	regmap = devm_regmap_init_i2c(client, &mp886x_regmap_config);
+	if (IS_ERR(regmap)) {
+		dev_err(dev, "Failed to allocate regmap!\n");
+		return PTR_ERR(regmap);
+	}
+	i2c_set_clientdata(client, di);
+
+	config.dev = di->dev;
+	config.init_data = di->regulator;
+	config.regmap = regmap;
+	config.driver_data = di;
+	config.of_node = np;
+
+	ret = mp886x_regulator_register(di, &config);
+	if (ret < 0)
+		dev_err(dev, "Failed to register regulator!\n");
+	return ret;
+}
+
+static const struct of_device_id mp886x_dt_ids[] = {
+	{
+		.compatible = "mps,mp8869",
+		.data = &mp8869_regulator_ops
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, mp886x_dt_ids);
+
+static const struct i2c_device_id mp886x_id[] = {
+	{ "mp886x", },
+	{ },
+};
+MODULE_DEVICE_TABLE(i2c, mp886x_id);
+
+static struct i2c_driver mp886x_regulator_driver = {
+	.driver = {
+		.name = "mp886x-regulator",
+		.of_match_table = of_match_ptr(mp886x_dt_ids),
+	},
+	.probe = mp886x_i2c_probe,
+	.id_table = mp886x_id,
+};
+module_i2c_driver(mp886x_regulator_driver);
+
+MODULE_AUTHOR("Jisheng Zhang <jszhang@kernel.org>");
+MODULE_DESCRIPTION("MP886x regulator driver");
+MODULE_LICENSE("GPL v2");
-- 
2.20.1