linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH 1/2] wcn36xx: populate band before determining rate on RX
@ 2021-10-28 22:31 Benjamin Li
  2021-10-28 22:31 ` [PATCH 2/2] wcn36xx: fix RX BD rate mapping for 5GHz legacy rates Benjamin Li
  0 siblings, 1 reply; 7+ messages in thread
From: Benjamin Li @ 2021-10-28 22:31 UTC (permalink / raw)
  To: Kalle Valo
  Cc: Bryan O'Donoghue, Loic Poulain, linux-arm-msm, Benjamin Li,
	David S. Miller, Jakub Kicinski, wcn36xx, linux-wireless, netdev,
	linux-kernel

status.band is used in determination of status.rate -- for 5GHz on legacy
rates there is a linear shift between the BD descriptor's rate field and
the wcn36xx driver's rate table (wcn_5ghz_rates).

We have a special clause to populate status.band for hardware scan offload
frames. However, this block occurs after status.rate is already populated.
Correctly handle this dependency by moving the band block before the rate
block.

This patch addresses kernel warnings & missing scan results for 5GHz APs
that send their probe responses at the higher four legacy rates (24-54
Mbps), when using hardware scan offload:

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:4532 ieee80211_rx_napi+0x744/0x8d8
  Modules linked in: wcn36xx [...]
  CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W         4.19.107-g73909fa #1
  Hardware name: Square, Inc. T2 (all variants) (DT)
  Call trace:
  dump_backtrace+0x0/0x148
  show_stack+0x14/0x1c
  dump_stack+0xb8/0xf0
  __warn+0x2ac/0x2d8
  warn_slowpath_null+0x44/0x54
  ieee80211_rx_napi+0x744/0x8d8
  ieee80211_tasklet_handler+0xa4/0xe0
  tasklet_action_common+0xe0/0x118
  tasklet_action+0x20/0x28
  __do_softirq+0x108/0x1ec
  irq_exit+0xd4/0xd8
  __handle_domain_irq+0x84/0xbc
  gic_handle_irq+0x4c/0xb8
  el1_irq+0xe8/0x190
  lpm_cpuidle_enter+0x220/0x260
  cpuidle_enter_state+0x114/0x1c0
  cpuidle_enter+0x34/0x48
  do_idle+0x150/0x268
  cpu_startup_entry+0x20/0x24
  rest_init+0xd4/0xe0
  start_kernel+0x398/0x430
  ---[ end trace ae28cb759352b403 ]---

Fixes: 8a27ca394782 ("wcn36xx: Correct band/freq reporting on RX")
Signed-off-by: Benjamin Li <benl@squareup.com>
---
 drivers/net/wireless/ath/wcn36xx/txrx.c | 37 +++++++++++++------------
 1 file changed, 19 insertions(+), 18 deletions(-)

diff --git a/drivers/net/wireless/ath/wcn36xx/txrx.c b/drivers/net/wireless/ath/wcn36xx/txrx.c
index 75951ccbc840e..f0a9f069a92a9 100644
--- a/drivers/net/wireless/ath/wcn36xx/txrx.c
+++ b/drivers/net/wireless/ath/wcn36xx/txrx.c
@@ -314,8 +314,6 @@ int wcn36xx_rx_skb(struct wcn36xx *wcn, struct sk_buff *skb)
 	fc = __le16_to_cpu(hdr->frame_control);
 	sn = IEEE80211_SEQ_TO_SN(__le16_to_cpu(hdr->seq_ctrl));
 
-	status.freq = WCN36XX_CENTER_FREQ(wcn);
-	status.band = WCN36XX_BAND(wcn);
 	status.mactime = 10;
 	status.signal = -get_rssi0(bd);
 	status.antenna = 1;
@@ -327,6 +325,25 @@ int wcn36xx_rx_skb(struct wcn36xx *wcn, struct sk_buff *skb)
 
 	wcn36xx_dbg(WCN36XX_DBG_RX, "status.flags=%x\n", status.flag);
 
+	if (bd->scan_learn) {
+		/* If packet originate from hardware scanning, extract the
+		 * band/channel from bd descriptor.
+		 */
+		u8 hwch = (bd->reserved0 << 4) + bd->rx_ch;
+
+		if (bd->rf_band != 1 && hwch <= sizeof(ab_rx_ch_map) && hwch >= 1) {
+			status.band = NL80211_BAND_5GHZ;
+			status.freq = ieee80211_channel_to_frequency(ab_rx_ch_map[hwch - 1],
+								     status.band);
+		} else {
+			status.band = NL80211_BAND_2GHZ;
+			status.freq = ieee80211_channel_to_frequency(hwch, status.band);
+		}
+	} else {
+		status.band = WCN36XX_BAND(wcn);
+		status.freq = WCN36XX_CENTER_FREQ(wcn);
+	}
+
 	if (bd->rate_id < ARRAY_SIZE(wcn36xx_rate_table)) {
 		rate = &wcn36xx_rate_table[bd->rate_id];
 		status.encoding = rate->encoding;
@@ -353,22 +370,6 @@ int wcn36xx_rx_skb(struct wcn36xx *wcn, struct sk_buff *skb)
 	    ieee80211_is_probe_resp(hdr->frame_control))
 		status.boottime_ns = ktime_get_boottime_ns();
 
-	if (bd->scan_learn) {
-		/* If packet originates from hardware scanning, extract the
-		 * band/channel from bd descriptor.
-		 */
-		u8 hwch = (bd->reserved0 << 4) + bd->rx_ch;
-
-		if (bd->rf_band != 1 && hwch <= sizeof(ab_rx_ch_map) && hwch >= 1) {
-			status.band = NL80211_BAND_5GHZ;
-			status.freq = ieee80211_channel_to_frequency(ab_rx_ch_map[hwch - 1],
-								     status.band);
-		} else {
-			status.band = NL80211_BAND_2GHZ;
-			status.freq = ieee80211_channel_to_frequency(hwch, status.band);
-		}
-	}
-
 	memcpy(IEEE80211_SKB_RXCB(skb), &status, sizeof(status));
 
 	if (ieee80211_is_beacon(hdr->frame_control)) {
-- 
2.25.1


^ permalink raw reply related	[flat|nested] 7+ messages in thread
end of thread, other threads:[~2021-11-01 13:00 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-10-28 22:31 [PATCH 1/2] wcn36xx: populate band before determining rate on RX Benjamin Li
2021-10-28 22:31 ` [PATCH 2/2] wcn36xx: fix RX BD rate mapping for 5GHz legacy rates Benjamin Li
2021-10-29  0:30   ` Bryan O'Donoghue
2021-10-29  0:39     ` Benjamin Li
2021-10-29  1:11       ` Bryan O'Donoghue
2021-11-01 13:00       ` Kalle Valo
2021-10-29 18:30   ` kernel test robot

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).