* [PATCH v10] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
@ 2020-05-19 18:53 Rakesh Pillai
2020-05-19 20:07 ` Doug Anderson
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Rakesh Pillai @ 2020-05-19 18:53 UTC (permalink / raw)
To: devicetree; +Cc: linux-arm-kernel, linux-kernel, linux-arm-msm, Rakesh Pillai
Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on sc7180 soc.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
---
Changes from v9:
- Place the wlan_fw_mem under reserved-memory node
---
arch/arm64/boot/dts/qcom/sc7180-idp.dts | 7 +++++++
arch/arm64/boot/dts/qcom/sc7180.dtsi | 27 +++++++++++++++++++++++++++
2 files changed, 34 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 4e9149d..38b102e 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -389,6 +389,13 @@
};
};
+&wifi {
+ status = "okay";
+ wifi-firmware {
+ iommus = <&apps_smmu 0xc2 0x1>;
+ };
+};
+
/* PINCTRL - additions to nodes defined in sc7180.dtsi */
&qspi_clk {
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index f1280e0..19bd7d0 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -106,6 +106,11 @@
no-map;
};
+ wlan_fw_mem: memory@94100000 {
+ reg = <0 0x94100000 0 0x200000>;
+ no-map;
+ };
+
rmtfs_mem: memory@84400000 {
compatible = "qcom,rmtfs-mem";
reg = <0x0 0x84400000 0x0 0x200000>;
@@ -944,6 +949,28 @@
};
};
+ wifi: wifi@18800000 {
+ compatible = "qcom,wcn3990-wifi";
+ reg = <0 0x18800000 0 0x800000>;
+ reg-names = "membase";
+ iommus = <&apps_smmu 0xc0 0x1>;
+ interrupts =
+ <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
+ <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
+ <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
+ <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
+ <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
+ <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
+ <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
+ <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
+ <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
+ <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
+ <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
+ <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
+ memory-region = <&wlan_fw_mem>;
+ status = "disabled";
+ };
+
config_noc: interconnect@1500000 {
compatible = "qcom,sc7180-config-noc";
reg = <0 0x01500000 0 0x28000>;
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH v10] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
2020-05-19 18:53 [PATCH v10] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Rakesh Pillai
@ 2020-05-19 20:07 ` Doug Anderson
2020-05-19 20:38 ` Doug Anderson
2020-05-20 3:34 ` Sibi Sankar
2 siblings, 0 replies; 4+ messages in thread
From: Doug Anderson @ 2020-05-19 20:07 UTC (permalink / raw)
To: Rakesh Pillai
Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-arm-msm, LKML, Linux ARM
Hi,
On Tue, May 19, 2020 at 11:53 AM Rakesh Pillai <pillair@codeaurora.org> wrote:
>
> Add device node for the ath10k SNOC platform driver probe
> and add resources required for WCN3990 on sc7180 soc.
>
> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> ---
> Changes from v9:
> - Place the wlan_fw_mem under reserved-memory node
> ---
> arch/arm64/boot/dts/qcom/sc7180-idp.dts | 7 +++++++
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 27 +++++++++++++++++++++++++++
> 2 files changed, 34 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 4e9149d..38b102e 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -389,6 +389,13 @@
> };
> };
>
> +&wifi {
> + status = "okay";
> + wifi-firmware {
> + iommus = <&apps_smmu 0xc2 0x1>;
> + };
> +};
> +
> /* PINCTRL - additions to nodes defined in sc7180.dtsi */
>
> &qspi_clk {
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index f1280e0..19bd7d0 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -106,6 +106,11 @@
> no-map;
> };
>
> + wlan_fw_mem: memory@94100000 {
> + reg = <0 0x94100000 0 0x200000>;
> + no-map;
> + };
> +
> rmtfs_mem: memory@84400000 {
> compatible = "qcom,rmtfs-mem";
> reg = <0x0 0x84400000 0x0 0x200000>;
This is less wrong than v9, but still a little wrong. You should be
keeping these ordered by unit address. 94100000 comes after 84400000.
-Doug
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH v10] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
2020-05-19 18:53 [PATCH v10] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Rakesh Pillai
2020-05-19 20:07 ` Doug Anderson
@ 2020-05-19 20:38 ` Doug Anderson
2020-05-20 3:34 ` Sibi Sankar
2 siblings, 0 replies; 4+ messages in thread
From: Doug Anderson @ 2020-05-19 20:38 UTC (permalink / raw)
To: Rakesh Pillai
Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-arm-msm, LKML, Linux ARM
Hi,
On Tue, May 19, 2020 at 11:53 AM Rakesh Pillai <pillair@codeaurora.org> wrote:
>
> + wifi: wifi@18800000 {
> + compatible = "qcom,wcn3990-wifi";
> + reg = <0 0x18800000 0 0x800000>;
> + reg-names = "membase";
> + iommus = <&apps_smmu 0xc0 0x1>;
> + interrupts =
> + <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
> + <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
> + <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
> + <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
> + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
> + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
> + <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
> + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
> + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
> + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
> + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
> + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
> + memory-region = <&wlan_fw_mem>;
> + status = "disabled";
> + };
> +
> config_noc: interconnect@1500000 {
> compatible = "qcom,sc7180-config-noc";
> reg = <0 0x01500000 0 0x28000>;
For completeness sake, I'll also point out that the WiFi node is also
sorted incorrectly. 0x18800000 comes after 0x01500000.
-Doug
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH v10] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node
2020-05-19 18:53 [PATCH v10] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Rakesh Pillai
2020-05-19 20:07 ` Doug Anderson
2020-05-19 20:38 ` Doug Anderson
@ 2020-05-20 3:34 ` Sibi Sankar
2 siblings, 0 replies; 4+ messages in thread
From: Sibi Sankar @ 2020-05-20 3:34 UTC (permalink / raw)
To: Rakesh Pillai
Cc: devicetree, linux-arm-kernel, linux-kernel, linux-arm-msm,
linux-arm-msm-owner
Hey Rakesh,
On 2020-05-20 00:23, Rakesh Pillai wrote:
> Add device node for the ath10k SNOC platform driver probe
> and add resources required for WCN3990 on sc7180 soc.
>
> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
> ---
> Changes from v9:
> - Place the wlan_fw_mem under reserved-memory node
> ---
> arch/arm64/boot/dts/qcom/sc7180-idp.dts | 7 +++++++
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 27
> +++++++++++++++++++++++++++
> 2 files changed, 34 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 4e9149d..38b102e 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -389,6 +389,13 @@
> };
> };
>
> +&wifi {
> + status = "okay";
> + wifi-firmware {
> + iommus = <&apps_smmu 0xc2 0x1>;
> + };
> +};
> +
> /* PINCTRL - additions to nodes defined in sc7180.dtsi */
>
> &qspi_clk {
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index f1280e0..19bd7d0 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -106,6 +106,11 @@
> no-map;
> };
>
> + wlan_fw_mem: memory@94100000 {
> + reg = <0 0x94100000 0 0x200000>;
> + no-map;
> + };
> +
You can skip ^^, its already
present as wlan_mem in the
board dts.
> rmtfs_mem: memory@84400000 {
> compatible = "qcom,rmtfs-mem";
> reg = <0x0 0x84400000 0x0 0x200000>;
> @@ -944,6 +949,28 @@
> };
> };
>
> + wifi: wifi@18800000 {
> + compatible = "qcom,wcn3990-wifi";
> + reg = <0 0x18800000 0 0x800000>;
> + reg-names = "membase";
> + iommus = <&apps_smmu 0xc0 0x1>;
> + interrupts =
> + <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH /* CE0 */ >,
> + <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH /* CE1 */ >,
> + <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH /* CE2 */ >,
> + <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH /* CE3 */ >,
> + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH /* CE4 */ >,
> + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH /* CE5 */ >,
> + <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH /* CE6 */ >,
> + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH /* CE7 */ >,
> + <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH /* CE8 */ >,
> + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH /* CE9 */ >,
> + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH /* CE10 */>,
> + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH /* CE11 */>;
> + memory-region = <&wlan_fw_mem>;
Its named as wlan_mem in sc7180-idp.dts
> + status = "disabled";
> + };
> +
> config_noc: interconnect@1500000 {
> compatible = "qcom,sc7180-config-noc";
> reg = <0 0x01500000 0 0x28000>;
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2020-05-20 3:34 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-05-19 18:53 [PATCH v10] arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node Rakesh Pillai
2020-05-19 20:07 ` Doug Anderson
2020-05-19 20:38 ` Doug Anderson
2020-05-20 3:34 ` Sibi Sankar
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).