* [PATCH 4/4] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel_sprout
@ 2022-12-14 9:33 Lux Aliaga
2022-12-14 9:52 ` Krzysztof Kozlowski
0 siblings, 1 reply; 8+ messages in thread
From: Lux Aliaga @ 2022-12-14 9:33 UTC (permalink / raw)
Cc: Lux Aliaga, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Rob Herring, Krzysztof Kozlowski, Kees Cook, Anton Vorontsov,
Colin Cross, Tony Luck, linux-arm-msm, devicetree, linux-kernel
This commit implements support for the Xiaomi Mi A3
(xiaomi-laurel_sprout). Here's a summary on what's working.
- dmesg output to bootloader preconfigured display
- USB
- UFS
- SMD RPM regulators
Signed-off-by: Lux Aliaga <they@mint.lgbt>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../dts/qcom/sm6125-xiaomi-laurel_sprout.dts | 251 ++++++++++++++++++
2 files changed, 252 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index d7669a7cee9f..7b4fbb4cbb84 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -140,6 +140,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-shift-axolotl.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm850-samsung-w737.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm6125-sony-xperia-seine-pdx201.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-laurel_sprout.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm6350-sony-xperia-lena-pdx213.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm7225-fairphone-fp4.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
new file mode 100644
index 000000000000..edc5f13bae28
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
@@ -0,0 +1,251 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Lux Aliaga <they@mint.lgbt>
+ */
+
+/dts-v1/;
+
+#include "sm6125.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/gpio-keys.h>
+
+/ {
+ /* required for bootloader to select correct board */
+ qcom,msm-id = <0x18a 0x00>; /* sm6125 v1 */
+ qcom,board-id = <0x0b 0x00>;
+
+ model = "Xiaomi Mi A3";
+ compatible = "xiaomi,laurel_sprout", "qcom,sm6125";
+ chassis-type = "handset";
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer0: framebuffer@5c000000 {
+ compatible = "simple-framebuffer";
+ reg = <0 0x5c000000 0 (1560 * 720 * 4)>;
+ width = <720>;
+ height = <1560>;
+ stride = <(720 * 4)>;
+ format = "a8r8g8b8";
+ };
+ };
+
+ extcon_usb: extcon-usb {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+ };
+
+ reserved_memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ debug_mem: memory@ffb00000 {
+ reg = <0x0 0xffb00000 0x0 0xc0000>;
+ no-map;
+ };
+
+ last_log_mem: memory@ffbc0000 {
+ reg = <0x0 0xffbc0000 0x0 0x80000>;
+ no-map;
+ };
+
+ pstore_mem: ramoops@ffc00000 {
+ compatible = "ramoops";
+ reg = <0x0 0xffc40000 0x0 0xc0000>;
+ record-size = <0x1000>;
+ console-size = <0x40000>;
+ msg-size = <0x20000 0x20000>;
+ };
+
+ cmdline_mem: memory@ffd00000 {
+ reg = <0x0 0xffd40000 0x0 0x1000>;
+ no-map;
+ };
+ };
+};
+
+&rpm_requests {
+ regulators-0 {
+ compatible = "qcom,rpm-pm6125-regulators";
+
+ vreg_s6a: s6 {
+ regulator-min-microvolt = <936000>;
+ regulator-max-microvolt = <1422000>;
+ };
+
+ vreg_l1a: l1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1256000>;
+ };
+
+ vreg_l2a: l2 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1056000>;
+ };
+
+ vreg_l3a: l3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1064000>;
+ };
+
+ vreg_l4a: l4 {
+ regulator-min-microvolt = <872000>;
+ regulator-max-microvolt = <976000>;
+ };
+
+ vreg_l5a: l5 {
+ regulator-min-microvolt = <1648000>;
+ regulator-max-microvolt = <3104000>;
+ };
+
+ vreg_l6a: l6 {
+ regulator-min-microvolt = <576000>;
+ regulator-max-microvolt = <656000>;
+ };
+
+ vreg_l7a: l7 {
+ regulator-min-microvolt = <872000>;
+ regulator-max-microvolt = <976000>;
+ };
+
+ vreg_l8a: l8 {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <728000>;
+ };
+
+ vreg_l9a: l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1896000>;
+ };
+
+ vreg_l10a: l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1896000>;
+ };
+
+ vreg_l11a: l11 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1952000>;
+ };
+
+ vreg_l12a: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1996000>;
+ };
+
+ vreg_l13a: l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1832000>;
+ };
+
+ vreg_l14a: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1904000>;
+ };
+
+ vreg_l15a: l15 {
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3232000>;
+ };
+
+ vreg_l16a: l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1904000>;
+ };
+
+ vreg_l17a: l17 {
+ regulator-min-microvolt = <1248000>;
+ regulator-max-microvolt = <1304000>;
+ };
+
+ vreg_l18a: l18 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1264000>;
+ };
+
+ vreg_l19a: l19 {
+ regulator-min-microvolt = <1648000>;
+ regulator-max-microvolt = <2952000>;
+ };
+
+ vreg_l20a: l20 {
+ regulator-min-microvolt = <1648000>;
+ regulator-max-microvolt = <2952000>;
+ };
+
+ vreg_l21a: l21 {
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2856000>;
+ };
+
+ vreg_l22a: l22 {
+ regulator-min-microvolt = <2944000>;
+ regulator-max-microvolt = <3304000>;
+ };
+
+ vreg_l23a: l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3400000>;
+ };
+
+ vreg_l24a: l24 {
+ regulator-min-microvolt = <2944000>;
+ regulator-max-microvolt = <3304000>;
+ };
+ };
+};
+
+&hsusb_phy1 {
+ status = "okay";
+};
+
+
+&sdc2_off_state {
+ sd-cd {
+ pins = "gpio98";
+ bias-disable;
+ drive-strength = <2>;
+ };
+};
+
+&sdc2_on_state {
+ sd-cd {
+ pins = "gpio98";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+};
+
+&ufs_mem_hc {
+ vcc-supply = <&vreg_l24a>;
+ vccq2-supply = <&vreg_l11a>;
+ vcc-max-microamp = <600000>;
+ vccq2-max-microamp = <600000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l4a>;
+ vdda-pll-supply = <&vreg_l10a>;
+ vdda-phy-max-microamp = <51400>;
+ vdda-pll-max-microamp = <14200>;
+ vddp-ref-clk-supply = <&vreg_l18a>;
+
+ status = "okay";
+};
+
+&tlmm {
+ gpio-reserved-ranges = <22 2>, <28 6>;
+};
+
+&usb3 {
+ status = "okay";
+};
+
+&usb3_dwc3 {
+ extcon = <&extcon_usb>;
+};
--
2.38.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH 4/4] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel_sprout
2022-12-14 9:33 [PATCH 4/4] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel_sprout Lux Aliaga
@ 2022-12-14 9:52 ` Krzysztof Kozlowski
2022-12-14 17:26 ` Lux Aliaga
0 siblings, 1 reply; 8+ messages in thread
From: Krzysztof Kozlowski @ 2022-12-14 9:52 UTC (permalink / raw)
To: Lux Aliaga
Cc: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Kees Cook, Anton Vorontsov, Colin Cross,
Tony Luck, linux-arm-msm, devicetree, linux-kernel
On 14/12/2022 10:33, Lux Aliaga wrote:
> This commit implements support for the Xiaomi Mi A3
> (xiaomi-laurel_sprout). Here's a summary on what's working.
>
> - dmesg output to bootloader preconfigured display
> - USB
> - UFS
> - SMD RPM regulators
>
> Signed-off-by: Lux Aliaga <they@mint.lgbt>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../dts/qcom/sm6125-xiaomi-laurel_sprout.dts | 251 ++++++++++++++++++
> 2 files changed, 252 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index d7669a7cee9f..7b4fbb4cbb84 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -140,6 +140,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-shift-axolotl.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm850-samsung-w737.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm6125-sony-xperia-seine-pdx201.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-laurel_sprout.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm6350-sony-xperia-lena-pdx213.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm7225-fairphone-fp4.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
> new file mode 100644
> index 000000000000..edc5f13bae28
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
> @@ -0,0 +1,251 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022, Lux Aliaga <they@mint.lgbt>
> + */
> +
> +/dts-v1/;
> +
> +#include "sm6125.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +
> +/ {
> + /* required for bootloader to select correct board */
> + qcom,msm-id = <0x18a 0x00>; /* sm6125 v1 */
> + qcom,board-id = <0x0b 0x00>;
> +
> + model = "Xiaomi Mi A3";
> + compatible = "xiaomi,laurel_sprout", "qcom,sm6125";
> + chassis-type = "handset";
> +
> + chosen {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + framebuffer0: framebuffer@5c000000 {
> + compatible = "simple-framebuffer";
> + reg = <0 0x5c000000 0 (1560 * 720 * 4)>;
> + width = <720>;
> + height = <1560>;
> + stride = <(720 * 4)>;
> + format = "a8r8g8b8";
> + };
> + };
> +
> + extcon_usb: extcon-usb {
Node name: usb-id
> + compatible = "linux,extcon-usb-gpio";
> + id-gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
> + };
> +
> + reserved_memory {
No underscores in node names. Use same node name as other boards, don't
invent own stuff.
> + #address-cells = <2>;
> + #size-cells = <2>;
> + debug_mem: memory@ffb00000 {
> + reg = <0x0 0xffb00000 0x0 0xc0000>;
> + no-map;
> + };
> +
> + last_log_mem: memory@ffbc0000 {
> + reg = <0x0 0xffbc0000 0x0 0x80000>;
> + no-map;
> + };
> +
> + pstore_mem: ramoops@ffc00000 {
> + compatible = "ramoops";
> + reg = <0x0 0xffc40000 0x0 0xc0000>;
> + record-size = <0x1000>;
> + console-size = <0x40000>;
> + msg-size = <0x20000 0x20000>;
> + };
> +
> + cmdline_mem: memory@ffd00000 {
> + reg = <0x0 0xffd40000 0x0 0x1000>;
> + no-map;
> + };
> + };
> +};
> +
> +&rpm_requests {
> + regulators-0 {
> + compatible = "qcom,rpm-pm6125-regulators";
> +
> + vreg_s6a: s6 {
> + regulator-min-microvolt = <936000>;
> + regulator-max-microvolt = <1422000>;
> + };
> +
> + vreg_l1a: l1 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1256000>;
> + };
> +
> + vreg_l2a: l2 {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1056000>;
> + };
> +
> + vreg_l3a: l3 {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1064000>;
> + };
> +
> + vreg_l4a: l4 {
> + regulator-min-microvolt = <872000>;
> + regulator-max-microvolt = <976000>;
> + };
> +
> + vreg_l5a: l5 {
> + regulator-min-microvolt = <1648000>;
> + regulator-max-microvolt = <3104000>;
> + };
> +
> + vreg_l6a: l6 {
> + regulator-min-microvolt = <576000>;
> + regulator-max-microvolt = <656000>;
> + };
> +
> + vreg_l7a: l7 {
> + regulator-min-microvolt = <872000>;
> + regulator-max-microvolt = <976000>;
> + };
> +
> + vreg_l8a: l8 {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <728000>;
> + };
> +
> + vreg_l9a: l9 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1896000>;
> + };
> +
> + vreg_l10a: l10 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1896000>;
> + };
> +
> + vreg_l11a: l11 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1952000>;
> + };
> +
> + vreg_l12a: l12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1996000>;
> + };
> +
> + vreg_l13a: l13 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1832000>;
> + };
> +
> + vreg_l14a: l14 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1904000>;
> + };
> +
> + vreg_l15a: l15 {
> + regulator-min-microvolt = <3104000>;
> + regulator-max-microvolt = <3232000>;
> + };
> +
> + vreg_l16a: l16 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1904000>;
> + };
> +
> + vreg_l17a: l17 {
> + regulator-min-microvolt = <1248000>;
> + regulator-max-microvolt = <1304000>;
> + };
> +
> + vreg_l18a: l18 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1264000>;
> + };
> +
> + vreg_l19a: l19 {
> + regulator-min-microvolt = <1648000>;
> + regulator-max-microvolt = <2952000>;
> + };
> +
> + vreg_l20a: l20 {
> + regulator-min-microvolt = <1648000>;
> + regulator-max-microvolt = <2952000>;
> + };
> +
> + vreg_l21a: l21 {
> + regulator-min-microvolt = <2600000>;
> + regulator-max-microvolt = <2856000>;
> + };
> +
> + vreg_l22a: l22 {
> + regulator-min-microvolt = <2944000>;
> + regulator-max-microvolt = <3304000>;
> + };
> +
> + vreg_l23a: l23 {
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3400000>;
> + };
> +
> + vreg_l24a: l24 {
> + regulator-min-microvolt = <2944000>;
> + regulator-max-microvolt = <3304000>;
> + };
> + };
> +};
> +
> +&hsusb_phy1 {
> + status = "okay";
> +};
> +
> +
> +&sdc2_off_state {
> + sd-cd {
Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).
that's missing -pins suffix but most likely it does not match other DTS
neither. So probably was based on some old kernel.
> + pins = "gpio98";
> + bias-disable;
> + drive-strength = <2>;
> + };
> +};
> +
> +&sdc2_on_state {
> + sd-cd {
Same problems.
> + pins = "gpio98";
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> +};
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 4/4] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel_sprout
2022-12-14 9:52 ` Krzysztof Kozlowski
@ 2022-12-14 17:26 ` Lux Aliaga
2022-12-14 17:45 ` Lux Aliaga
2022-12-15 8:30 ` Krzysztof Kozlowski
0 siblings, 2 replies; 8+ messages in thread
From: Lux Aliaga @ 2022-12-14 17:26 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Kees Cook, Anton Vorontsov, Colin Cross,
Tony Luck, linux-arm-msm, devicetree, linux-kernel
I'm a bit confused at the "Node name: usb-id" comment. Should I change
"extcon_usb" or "extcon-usb" to usb-id?
On 14/12/2022 06:52, Krzysztof Kozlowski wrote:
> On 14/12/2022 10:33, Lux Aliaga wrote:
>> This commit implements support for the Xiaomi Mi A3
>> (xiaomi-laurel_sprout). Here's a summary on what's working.
>>
>> - dmesg output to bootloader preconfigured display
>> - USB
>> - UFS
>> - SMD RPM regulators
>>
>> Signed-off-by: Lux Aliaga <they@mint.lgbt>
>> ---
>> arch/arm64/boot/dts/qcom/Makefile | 1 +
>> .../dts/qcom/sm6125-xiaomi-laurel_sprout.dts | 251 ++++++++++++++++++
>> 2 files changed, 252 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index d7669a7cee9f..7b4fbb4cbb84 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -140,6 +140,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-shift-axolotl.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += sdm850-samsung-w737.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += sm6125-sony-xperia-seine-pdx201.dtb
>> +dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-laurel_sprout.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += sm6350-sony-xperia-lena-pdx213.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += sm7225-fairphone-fp4.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>> new file mode 100644
>> index 000000000000..edc5f13bae28
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>> @@ -0,0 +1,251 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +/*
>> + * Copyright (c) 2022, Lux Aliaga <they@mint.lgbt>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "sm6125.dtsi"
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> +#include <dt-bindings/input/gpio-keys.h>
>> +
>> +/ {
>> + /* required for bootloader to select correct board */
>> + qcom,msm-id = <0x18a 0x00>; /* sm6125 v1 */
>> + qcom,board-id = <0x0b 0x00>;
>> +
>> + model = "Xiaomi Mi A3";
>> + compatible = "xiaomi,laurel_sprout", "qcom,sm6125";
>> + chassis-type = "handset";
>> +
>> + chosen {
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> +
>> + framebuffer0: framebuffer@5c000000 {
>> + compatible = "simple-framebuffer";
>> + reg = <0 0x5c000000 0 (1560 * 720 * 4)>;
>> + width = <720>;
>> + height = <1560>;
>> + stride = <(720 * 4)>;
>> + format = "a8r8g8b8";
>> + };
>> + };
>> +
>> + extcon_usb: extcon-usb {
> Node name: usb-id
>
>> + compatible = "linux,extcon-usb-gpio";
>> + id-gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + reserved_memory {
> No underscores in node names. Use same node name as other boards, don't
> invent own stuff.
>
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + debug_mem: memory@ffb00000 {
>> + reg = <0x0 0xffb00000 0x0 0xc0000>;
>> + no-map;
>> + };
>> +
>> + last_log_mem: memory@ffbc0000 {
>> + reg = <0x0 0xffbc0000 0x0 0x80000>;
>> + no-map;
>> + };
>> +
>> + pstore_mem: ramoops@ffc00000 {
>> + compatible = "ramoops";
>> + reg = <0x0 0xffc40000 0x0 0xc0000>;
>> + record-size = <0x1000>;
>> + console-size = <0x40000>;
>> + msg-size = <0x20000 0x20000>;
>> + };
>> +
>> + cmdline_mem: memory@ffd00000 {
>> + reg = <0x0 0xffd40000 0x0 0x1000>;
>> + no-map;
>> + };
>> + };
>> +};
>> +
>> +&rpm_requests {
>> + regulators-0 {
>> + compatible = "qcom,rpm-pm6125-regulators";
>> +
>> + vreg_s6a: s6 {
>> + regulator-min-microvolt = <936000>;
>> + regulator-max-microvolt = <1422000>;
>> + };
>> +
>> + vreg_l1a: l1 {
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1256000>;
>> + };
>> +
>> + vreg_l2a: l2 {
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1056000>;
>> + };
>> +
>> + vreg_l3a: l3 {
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1064000>;
>> + };
>> +
>> + vreg_l4a: l4 {
>> + regulator-min-microvolt = <872000>;
>> + regulator-max-microvolt = <976000>;
>> + };
>> +
>> + vreg_l5a: l5 {
>> + regulator-min-microvolt = <1648000>;
>> + regulator-max-microvolt = <3104000>;
>> + };
>> +
>> + vreg_l6a: l6 {
>> + regulator-min-microvolt = <576000>;
>> + regulator-max-microvolt = <656000>;
>> + };
>> +
>> + vreg_l7a: l7 {
>> + regulator-min-microvolt = <872000>;
>> + regulator-max-microvolt = <976000>;
>> + };
>> +
>> + vreg_l8a: l8 {
>> + regulator-min-microvolt = <400000>;
>> + regulator-max-microvolt = <728000>;
>> + };
>> +
>> + vreg_l9a: l9 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1896000>;
>> + };
>> +
>> + vreg_l10a: l10 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1896000>;
>> + };
>> +
>> + vreg_l11a: l11 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1952000>;
>> + };
>> +
>> + vreg_l12a: l12 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1996000>;
>> + };
>> +
>> + vreg_l13a: l13 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1832000>;
>> + };
>> +
>> + vreg_l14a: l14 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1904000>;
>> + };
>> +
>> + vreg_l15a: l15 {
>> + regulator-min-microvolt = <3104000>;
>> + regulator-max-microvolt = <3232000>;
>> + };
>> +
>> + vreg_l16a: l16 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1904000>;
>> + };
>> +
>> + vreg_l17a: l17 {
>> + regulator-min-microvolt = <1248000>;
>> + regulator-max-microvolt = <1304000>;
>> + };
>> +
>> + vreg_l18a: l18 {
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1264000>;
>> + };
>> +
>> + vreg_l19a: l19 {
>> + regulator-min-microvolt = <1648000>;
>> + regulator-max-microvolt = <2952000>;
>> + };
>> +
>> + vreg_l20a: l20 {
>> + regulator-min-microvolt = <1648000>;
>> + regulator-max-microvolt = <2952000>;
>> + };
>> +
>> + vreg_l21a: l21 {
>> + regulator-min-microvolt = <2600000>;
>> + regulator-max-microvolt = <2856000>;
>> + };
>> +
>> + vreg_l22a: l22 {
>> + regulator-min-microvolt = <2944000>;
>> + regulator-max-microvolt = <3304000>;
>> + };
>> +
>> + vreg_l23a: l23 {
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3400000>;
>> + };
>> +
>> + vreg_l24a: l24 {
>> + regulator-min-microvolt = <2944000>;
>> + regulator-max-microvolt = <3304000>;
>> + };
>> + };
>> +};
>> +
>> +&hsusb_phy1 {
>> + status = "okay";
>> +};
>> +
>> +
>> +&sdc2_off_state {
>> + sd-cd {
> Does not look like you tested the DTS against bindings. Please run `make
> dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
> for instructions).
>
> that's missing -pins suffix but most likely it does not match other DTS
> neither. So probably was based on some old kernel.
>
>> + pins = "gpio98";
>> + bias-disable;
>> + drive-strength = <2>;
>> + };
>> +};
>> +
>> +&sdc2_on_state {
>> + sd-cd {
> Same problems.
>
>> + pins = "gpio98";
>> + bias-pull-up;
>> + drive-strength = <2>;
>> + };
>> +};
> Best regards,
> Krzysztof
>
--
Lux Aliaga
https://nixgoat.me/
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 4/4] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel_sprout
2022-12-14 17:26 ` Lux Aliaga
@ 2022-12-14 17:45 ` Lux Aliaga
2022-12-14 20:27 ` Konrad Dybcio
2022-12-15 8:31 ` Krzysztof Kozlowski
2022-12-15 8:30 ` Krzysztof Kozlowski
1 sibling, 2 replies; 8+ messages in thread
From: Lux Aliaga @ 2022-12-14 17:45 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Kees Cook, Anton Vorontsov, Colin Cross,
Tony Luck, linux-arm-msm, devicetree, linux-kernel
Ok. I think that comment is incorrect. Changing the node name on
extcon_usb breaks the "extcon" property in &usb3_dwc3, even after
changing the reference.
On 14/12/2022 14:26, Lux Aliaga wrote:
> I'm a bit confused at the "Node name: usb-id" comment. Should I change
> "extcon_usb" or "extcon-usb" to usb-id?
>
> On 14/12/2022 06:52, Krzysztof Kozlowski wrote:
>> On 14/12/2022 10:33, Lux Aliaga wrote:
>>> This commit implements support for the Xiaomi Mi A3
>>> (xiaomi-laurel_sprout). Here's a summary on what's working.
>>>
>>> - dmesg output to bootloader preconfigured display
>>> - USB
>>> - UFS
>>> - SMD RPM regulators
>>>
>>> Signed-off-by: Lux Aliaga <they@mint.lgbt>
>>> ---
>>> arch/arm64/boot/dts/qcom/Makefile | 1 +
>>> .../dts/qcom/sm6125-xiaomi-laurel_sprout.dts | 251
>>> ++++++++++++++++++
>>> 2 files changed, 252 insertions(+)
>>> create mode 100644
>>> arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/Makefile
>>> b/arch/arm64/boot/dts/qcom/Makefile
>>> index d7669a7cee9f..7b4fbb4cbb84 100644
>>> --- a/arch/arm64/boot/dts/qcom/Makefile
>>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>>> @@ -140,6 +140,7 @@ dtb-$(CONFIG_ARCH_QCOM) +=
>>> sdm845-shift-axolotl.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += sdm850-samsung-w737.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += sm6125-sony-xperia-seine-pdx201.dtb
>>> +dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-laurel_sprout.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += sm6350-sony-xperia-lena-pdx213.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += sm7225-fairphone-fp4.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb
>>> diff --git
>>> a/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>>> b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>>> new file mode 100644
>>> index 000000000000..edc5f13bae28
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>>> @@ -0,0 +1,251 @@
>>> +// SPDX-License-Identifier: BSD-3-Clause
>>> +/*
>>> + * Copyright (c) 2022, Lux Aliaga <they@mint.lgbt>
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "sm6125.dtsi"
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +#include <dt-bindings/input/input.h>
>>> +#include <dt-bindings/input/gpio-keys.h>
>>> +
>>> +/ {
>>> + /* required for bootloader to select correct board */
>>> + qcom,msm-id = <0x18a 0x00>; /* sm6125 v1 */
>>> + qcom,board-id = <0x0b 0x00>;
>>> +
>>> + model = "Xiaomi Mi A3";
>>> + compatible = "xiaomi,laurel_sprout", "qcom,sm6125";
>>> + chassis-type = "handset";
>>> +
>>> + chosen {
>>> + #address-cells = <2>;
>>> + #size-cells = <2>;
>>> + ranges;
>>> +
>>> + framebuffer0: framebuffer@5c000000 {
>>> + compatible = "simple-framebuffer";
>>> + reg = <0 0x5c000000 0 (1560 * 720 * 4)>;
>>> + width = <720>;
>>> + height = <1560>;
>>> + stride = <(720 * 4)>;
>>> + format = "a8r8g8b8";
>>> + };
>>> + };
>>> +
>>> + extcon_usb: extcon-usb {
>> Node name: usb-id
>>
>>> + compatible = "linux,extcon-usb-gpio";
>>> + id-gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
>>> + };
>>> +
>>> + reserved_memory {
>> No underscores in node names. Use same node name as other boards, don't
>> invent own stuff.
>>
>>> + #address-cells = <2>;
>>> + #size-cells = <2>;
>>> + debug_mem: memory@ffb00000 {
>>> + reg = <0x0 0xffb00000 0x0 0xc0000>;
>>> + no-map;
>>> + };
>>> +
>>> + last_log_mem: memory@ffbc0000 {
>>> + reg = <0x0 0xffbc0000 0x0 0x80000>;
>>> + no-map;
>>> + };
>>> +
>>> + pstore_mem: ramoops@ffc00000 {
>>> + compatible = "ramoops";
>>> + reg = <0x0 0xffc40000 0x0 0xc0000>;
>>> + record-size = <0x1000>;
>>> + console-size = <0x40000>;
>>> + msg-size = <0x20000 0x20000>;
>>> + };
>>> +
>>> + cmdline_mem: memory@ffd00000 {
>>> + reg = <0x0 0xffd40000 0x0 0x1000>;
>>> + no-map;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&rpm_requests {
>>> + regulators-0 {
>>> + compatible = "qcom,rpm-pm6125-regulators";
>>> +
>>> + vreg_s6a: s6 {
>>> + regulator-min-microvolt = <936000>;
>>> + regulator-max-microvolt = <1422000>;
>>> + };
>>> +
>>> + vreg_l1a: l1 {
>>> + regulator-min-microvolt = <1200000>;
>>> + regulator-max-microvolt = <1256000>;
>>> + };
>>> +
>>> + vreg_l2a: l2 {
>>> + regulator-min-microvolt = <1000000>;
>>> + regulator-max-microvolt = <1056000>;
>>> + };
>>> +
>>> + vreg_l3a: l3 {
>>> + regulator-min-microvolt = <1000000>;
>>> + regulator-max-microvolt = <1064000>;
>>> + };
>>> +
>>> + vreg_l4a: l4 {
>>> + regulator-min-microvolt = <872000>;
>>> + regulator-max-microvolt = <976000>;
>>> + };
>>> +
>>> + vreg_l5a: l5 {
>>> + regulator-min-microvolt = <1648000>;
>>> + regulator-max-microvolt = <3104000>;
>>> + };
>>> +
>>> + vreg_l6a: l6 {
>>> + regulator-min-microvolt = <576000>;
>>> + regulator-max-microvolt = <656000>;
>>> + };
>>> +
>>> + vreg_l7a: l7 {
>>> + regulator-min-microvolt = <872000>;
>>> + regulator-max-microvolt = <976000>;
>>> + };
>>> +
>>> + vreg_l8a: l8 {
>>> + regulator-min-microvolt = <400000>;
>>> + regulator-max-microvolt = <728000>;
>>> + };
>>> +
>>> + vreg_l9a: l9 {
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1896000>;
>>> + };
>>> +
>>> + vreg_l10a: l10 {
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1896000>;
>>> + };
>>> +
>>> + vreg_l11a: l11 {
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1952000>;
>>> + };
>>> +
>>> + vreg_l12a: l12 {
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1996000>;
>>> + };
>>> +
>>> + vreg_l13a: l13 {
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1832000>;
>>> + };
>>> +
>>> + vreg_l14a: l14 {
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1904000>;
>>> + };
>>> +
>>> + vreg_l15a: l15 {
>>> + regulator-min-microvolt = <3104000>;
>>> + regulator-max-microvolt = <3232000>;
>>> + };
>>> +
>>> + vreg_l16a: l16 {
>>> + regulator-min-microvolt = <1800000>;
>>> + regulator-max-microvolt = <1904000>;
>>> + };
>>> +
>>> + vreg_l17a: l17 {
>>> + regulator-min-microvolt = <1248000>;
>>> + regulator-max-microvolt = <1304000>;
>>> + };
>>> +
>>> + vreg_l18a: l18 {
>>> + regulator-min-microvolt = <1200000>;
>>> + regulator-max-microvolt = <1264000>;
>>> + };
>>> +
>>> + vreg_l19a: l19 {
>>> + regulator-min-microvolt = <1648000>;
>>> + regulator-max-microvolt = <2952000>;
>>> + };
>>> +
>>> + vreg_l20a: l20 {
>>> + regulator-min-microvolt = <1648000>;
>>> + regulator-max-microvolt = <2952000>;
>>> + };
>>> +
>>> + vreg_l21a: l21 {
>>> + regulator-min-microvolt = <2600000>;
>>> + regulator-max-microvolt = <2856000>;
>>> + };
>>> +
>>> + vreg_l22a: l22 {
>>> + regulator-min-microvolt = <2944000>;
>>> + regulator-max-microvolt = <3304000>;
>>> + };
>>> +
>>> + vreg_l23a: l23 {
>>> + regulator-min-microvolt = <3000000>;
>>> + regulator-max-microvolt = <3400000>;
>>> + };
>>> +
>>> + vreg_l24a: l24 {
>>> + regulator-min-microvolt = <2944000>;
>>> + regulator-max-microvolt = <3304000>;
>>> + };
>>> + };
>>> +};
>>> +
>>> +&hsusb_phy1 {
>>> + status = "okay";
>>> +};
>>> +
>>> +
>>> +&sdc2_off_state {
>>> + sd-cd {
>> Does not look like you tested the DTS against bindings. Please run `make
>> dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
>> for instructions).
>>
>> that's missing -pins suffix but most likely it does not match other DTS
>> neither. So probably was based on some old kernel.
>>
>>> + pins = "gpio98";
>>> + bias-disable;
>>> + drive-strength = <2>;
>>> + };
>>> +};
>>> +
>>> +&sdc2_on_state {
>>> + sd-cd {
>> Same problems.
>>
>>> + pins = "gpio98";
>>> + bias-pull-up;
>>> + drive-strength = <2>;
>>> + };
>>> +};
>> Best regards,
>> Krzysztof
>>
--
Lux Aliaga
https://nixgoat.me/
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 4/4] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel_sprout
2022-12-14 17:45 ` Lux Aliaga
@ 2022-12-14 20:27 ` Konrad Dybcio
2022-12-15 8:31 ` Krzysztof Kozlowski
1 sibling, 0 replies; 8+ messages in thread
From: Konrad Dybcio @ 2022-12-14 20:27 UTC (permalink / raw)
To: Lux Aliaga, Krzysztof Kozlowski
Cc: Andy Gross, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Kees Cook, Anton Vorontsov, Colin Cross, Tony Luck,
linux-arm-msm, devicetree, linux-kernel
On 14.12.2022 18:45, Lux Aliaga wrote:
> Ok. I think that comment is incorrect. Changing the node name on extcon_usb breaks the "extcon" property in &usb3_dwc3, even after changing the reference.
>
Please don't toppost, reply under the paragraph you're referencing.
Konrad
> On 14/12/2022 14:26, Lux Aliaga wrote:
>> I'm a bit confused at the "Node name: usb-id" comment. Should I change "extcon_usb" or "extcon-usb" to usb-id?
>>
>> On 14/12/2022 06:52, Krzysztof Kozlowski wrote:
>>> On 14/12/2022 10:33, Lux Aliaga wrote:
>>>> This commit implements support for the Xiaomi Mi A3
>>>> (xiaomi-laurel_sprout). Here's a summary on what's working.
>>>>
>>>> - dmesg output to bootloader preconfigured display
>>>> - USB
>>>> - UFS
>>>> - SMD RPM regulators
>>>>
>>>> Signed-off-by: Lux Aliaga <they@mint.lgbt>
>>>> ---
>>>> arch/arm64/boot/dts/qcom/Makefile | 1 +
>>>> .../dts/qcom/sm6125-xiaomi-laurel_sprout.dts | 251 ++++++++++++++++++
>>>> 2 files changed, 252 insertions(+)
>>>> create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>>>>
>>>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>>>> index d7669a7cee9f..7b4fbb4cbb84 100644
>>>> --- a/arch/arm64/boot/dts/qcom/Makefile
>>>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>>>> @@ -140,6 +140,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-shift-axolotl.dtb
>>>> dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
>>>> dtb-$(CONFIG_ARCH_QCOM) += sdm850-samsung-w737.dtb
>>>> dtb-$(CONFIG_ARCH_QCOM) += sm6125-sony-xperia-seine-pdx201.dtb
>>>> +dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-laurel_sprout.dtb
>>>> dtb-$(CONFIG_ARCH_QCOM) += sm6350-sony-xperia-lena-pdx213.dtb
>>>> dtb-$(CONFIG_ARCH_QCOM) += sm7225-fairphone-fp4.dtb
>>>> dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb
>>>> diff --git a/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>>>> new file mode 100644
>>>> index 000000000000..edc5f13bae28
>>>> --- /dev/null
>>>> +++ b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-laurel_sprout.dts
>>>> @@ -0,0 +1,251 @@
>>>> +// SPDX-License-Identifier: BSD-3-Clause
>>>> +/*
>>>> + * Copyright (c) 2022, Lux Aliaga <they@mint.lgbt>
>>>> + */
>>>> +
>>>> +/dts-v1/;
>>>> +
>>>> +#include "sm6125.dtsi"
>>>> +#include <dt-bindings/gpio/gpio.h>
>>>> +#include <dt-bindings/input/input.h>
>>>> +#include <dt-bindings/input/gpio-keys.h>
>>>> +
>>>> +/ {
>>>> + /* required for bootloader to select correct board */
>>>> + qcom,msm-id = <0x18a 0x00>; /* sm6125 v1 */
>>>> + qcom,board-id = <0x0b 0x00>;
>>>> +
>>>> + model = "Xiaomi Mi A3";
>>>> + compatible = "xiaomi,laurel_sprout", "qcom,sm6125";
>>>> + chassis-type = "handset";
>>>> +
>>>> + chosen {
>>>> + #address-cells = <2>;
>>>> + #size-cells = <2>;
>>>> + ranges;
>>>> +
>>>> + framebuffer0: framebuffer@5c000000 {
>>>> + compatible = "simple-framebuffer";
>>>> + reg = <0 0x5c000000 0 (1560 * 720 * 4)>;
>>>> + width = <720>;
>>>> + height = <1560>;
>>>> + stride = <(720 * 4)>;
>>>> + format = "a8r8g8b8";
>>>> + };
>>>> + };
>>>> +
>>>> + extcon_usb: extcon-usb {
>>> Node name: usb-id
>>>
>>>> + compatible = "linux,extcon-usb-gpio";
>>>> + id-gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
>>>> + };
>>>> +
>>>> + reserved_memory {
>>> No underscores in node names. Use same node name as other boards, don't
>>> invent own stuff.
>>>
>>>> + #address-cells = <2>;
>>>> + #size-cells = <2>;
>>>> + debug_mem: memory@ffb00000 {
>>>> + reg = <0x0 0xffb00000 0x0 0xc0000>;
>>>> + no-map;
>>>> + };
>>>> +
>>>> + last_log_mem: memory@ffbc0000 {
>>>> + reg = <0x0 0xffbc0000 0x0 0x80000>;
>>>> + no-map;
>>>> + };
>>>> +
>>>> + pstore_mem: ramoops@ffc00000 {
>>>> + compatible = "ramoops";
>>>> + reg = <0x0 0xffc40000 0x0 0xc0000>;
>>>> + record-size = <0x1000>;
>>>> + console-size = <0x40000>;
>>>> + msg-size = <0x20000 0x20000>;
>>>> + };
>>>> +
>>>> + cmdline_mem: memory@ffd00000 {
>>>> + reg = <0x0 0xffd40000 0x0 0x1000>;
>>>> + no-map;
>>>> + };
>>>> + };
>>>> +};
>>>> +
>>>> +&rpm_requests {
>>>> + regulators-0 {
>>>> + compatible = "qcom,rpm-pm6125-regulators";
>>>> +
>>>> + vreg_s6a: s6 {
>>>> + regulator-min-microvolt = <936000>;
>>>> + regulator-max-microvolt = <1422000>;
>>>> + };
>>>> +
>>>> + vreg_l1a: l1 {
>>>> + regulator-min-microvolt = <1200000>;
>>>> + regulator-max-microvolt = <1256000>;
>>>> + };
>>>> +
>>>> + vreg_l2a: l2 {
>>>> + regulator-min-microvolt = <1000000>;
>>>> + regulator-max-microvolt = <1056000>;
>>>> + };
>>>> +
>>>> + vreg_l3a: l3 {
>>>> + regulator-min-microvolt = <1000000>;
>>>> + regulator-max-microvolt = <1064000>;
>>>> + };
>>>> +
>>>> + vreg_l4a: l4 {
>>>> + regulator-min-microvolt = <872000>;
>>>> + regulator-max-microvolt = <976000>;
>>>> + };
>>>> +
>>>> + vreg_l5a: l5 {
>>>> + regulator-min-microvolt = <1648000>;
>>>> + regulator-max-microvolt = <3104000>;
>>>> + };
>>>> +
>>>> + vreg_l6a: l6 {
>>>> + regulator-min-microvolt = <576000>;
>>>> + regulator-max-microvolt = <656000>;
>>>> + };
>>>> +
>>>> + vreg_l7a: l7 {
>>>> + regulator-min-microvolt = <872000>;
>>>> + regulator-max-microvolt = <976000>;
>>>> + };
>>>> +
>>>> + vreg_l8a: l8 {
>>>> + regulator-min-microvolt = <400000>;
>>>> + regulator-max-microvolt = <728000>;
>>>> + };
>>>> +
>>>> + vreg_l9a: l9 {
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <1896000>;
>>>> + };
>>>> +
>>>> + vreg_l10a: l10 {
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <1896000>;
>>>> + };
>>>> +
>>>> + vreg_l11a: l11 {
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <1952000>;
>>>> + };
>>>> +
>>>> + vreg_l12a: l12 {
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <1996000>;
>>>> + };
>>>> +
>>>> + vreg_l13a: l13 {
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <1832000>;
>>>> + };
>>>> +
>>>> + vreg_l14a: l14 {
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <1904000>;
>>>> + };
>>>> +
>>>> + vreg_l15a: l15 {
>>>> + regulator-min-microvolt = <3104000>;
>>>> + regulator-max-microvolt = <3232000>;
>>>> + };
>>>> +
>>>> + vreg_l16a: l16 {
>>>> + regulator-min-microvolt = <1800000>;
>>>> + regulator-max-microvolt = <1904000>;
>>>> + };
>>>> +
>>>> + vreg_l17a: l17 {
>>>> + regulator-min-microvolt = <1248000>;
>>>> + regulator-max-microvolt = <1304000>;
>>>> + };
>>>> +
>>>> + vreg_l18a: l18 {
>>>> + regulator-min-microvolt = <1200000>;
>>>> + regulator-max-microvolt = <1264000>;
>>>> + };
>>>> +
>>>> + vreg_l19a: l19 {
>>>> + regulator-min-microvolt = <1648000>;
>>>> + regulator-max-microvolt = <2952000>;
>>>> + };
>>>> +
>>>> + vreg_l20a: l20 {
>>>> + regulator-min-microvolt = <1648000>;
>>>> + regulator-max-microvolt = <2952000>;
>>>> + };
>>>> +
>>>> + vreg_l21a: l21 {
>>>> + regulator-min-microvolt = <2600000>;
>>>> + regulator-max-microvolt = <2856000>;
>>>> + };
>>>> +
>>>> + vreg_l22a: l22 {
>>>> + regulator-min-microvolt = <2944000>;
>>>> + regulator-max-microvolt = <3304000>;
>>>> + };
>>>> +
>>>> + vreg_l23a: l23 {
>>>> + regulator-min-microvolt = <3000000>;
>>>> + regulator-max-microvolt = <3400000>;
>>>> + };
>>>> +
>>>> + vreg_l24a: l24 {
>>>> + regulator-min-microvolt = <2944000>;
>>>> + regulator-max-microvolt = <3304000>;
>>>> + };
>>>> + };
>>>> +};
>>>> +
>>>> +&hsusb_phy1 {
>>>> + status = "okay";
>>>> +};
>>>> +
>>>> +
>>>> +&sdc2_off_state {
>>>> + sd-cd {
>>> Does not look like you tested the DTS against bindings. Please run `make
>>> dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
>>> for instructions).
>>>
>>> that's missing -pins suffix but most likely it does not match other DTS
>>> neither. So probably was based on some old kernel.
>>>
>>>> + pins = "gpio98";
>>>> + bias-disable;
>>>> + drive-strength = <2>;
>>>> + };
>>>> +};
>>>> +
>>>> +&sdc2_on_state {
>>>> + sd-cd {
>>> Same problems.
>>>
>>>> + pins = "gpio98";
>>>> + bias-pull-up;
>>>> + drive-strength = <2>;
>>>> + };
>>>> +};
>>> Best regards,
>>> Krzysztof
>>>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 4/4] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel_sprout
2022-12-14 17:26 ` Lux Aliaga
2022-12-14 17:45 ` Lux Aliaga
@ 2022-12-15 8:30 ` Krzysztof Kozlowski
1 sibling, 0 replies; 8+ messages in thread
From: Krzysztof Kozlowski @ 2022-12-15 8:30 UTC (permalink / raw)
To: Lux Aliaga
Cc: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Kees Cook, Anton Vorontsov, Colin Cross,
Tony Luck, linux-arm-msm, devicetree, linux-kernel
On 14/12/2022 18:26, Lux Aliaga wrote:
> I'm a bit confused at the "Node name: usb-id" comment. Should I change
> "extcon_usb" or "extcon-usb" to usb-id?
Please change the node name, not the label. So extcon-usb goes to usb-id.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 4/4] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel_sprout
2022-12-14 17:45 ` Lux Aliaga
2022-12-14 20:27 ` Konrad Dybcio
@ 2022-12-15 8:31 ` Krzysztof Kozlowski
2022-12-15 16:06 ` Lux Aliaga
1 sibling, 1 reply; 8+ messages in thread
From: Krzysztof Kozlowski @ 2022-12-15 8:31 UTC (permalink / raw)
To: Lux Aliaga
Cc: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Kees Cook, Anton Vorontsov, Colin Cross,
Tony Luck, linux-arm-msm, devicetree, linux-kernel
On 14/12/2022 18:45, Lux Aliaga wrote:
> Ok. I think that comment is incorrect. Changing the node name on
> extcon_usb breaks the "extcon" property in &usb3_dwc3, even after
> changing the reference.
You top-post and I have no clue what do you refer to. Don't top-post.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 4/4] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel_sprout
2022-12-15 8:31 ` Krzysztof Kozlowski
@ 2022-12-15 16:06 ` Lux Aliaga
0 siblings, 0 replies; 8+ messages in thread
From: Lux Aliaga @ 2022-12-15 16:06 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andy Gross, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Kees Cook, Anton Vorontsov, Colin Cross,
Tony Luck, linux-arm-msm, devicetree, linux-kernel
On 15/12/2022 05:31, Krzysztof Kozlowski wrote:
> On 14/12/2022 18:45, Lux Aliaga wrote:
>> Ok. I think that comment is incorrect. Changing the node name on
>> extcon_usb breaks the "extcon" property in &usb3_dwc3, even after
>> changing the reference.
> You top-post and I have no clue what do you refer to. Don't top-post.
My apologies. I replied a bit too quickly and didn't check if the
concerns I proposed were redacted correctly. An email you sent already
answered my concern, so I'll proceed to send a new version of the patchset.
Kind regards.
--
Lux Aliaga
https://nixgoat.me/
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2022-12-15 16:07 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-12-14 9:33 [PATCH 4/4] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel_sprout Lux Aliaga
2022-12-14 9:52 ` Krzysztof Kozlowski
2022-12-14 17:26 ` Lux Aliaga
2022-12-14 17:45 ` Lux Aliaga
2022-12-14 20:27 ` Konrad Dybcio
2022-12-15 8:31 ` Krzysztof Kozlowski
2022-12-15 16:06 ` Lux Aliaga
2022-12-15 8:30 ` Krzysztof Kozlowski
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).