From: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
To: Konrad Dybcio <konrad.dybcio@linaro.org>, <agross@kernel.org>,
<andersson@kernel.org>, <robh+dt@kernel.org>,
<krzysztof.kozlowski+dt@linaro.org>, <mturquette@baylibre.com>,
<sboyd@kernel.org>, <ulf.hansson@linaro.org>,
<linus.walleij@linaro.org>, <catalin.marinas@arm.com>,
<will@kernel.org>, <shawnguo@kernel.org>, <arnd@arndb.de>,
<marcel.ziswiler@toradex.com>, <dmitry.baryshkov@linaro.org>,
<nfraprado@collabora.com>, <broonie@kernel.org>,
<robimarko@gmail.com>, <quic_gurus@quicinc.com>,
<bhupesh.sharma@linaro.org>, <linux-arm-msm@vger.kernel.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-clk@vger.kernel.org>, <linux-mmc@vger.kernel.org>,
<linux-gpio@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH 09/10] arm64: dts: qcom: add IPQ5332 SoC and MI01.2 board support
Date: Mon, 30 Jan 2023 17:26:32 +0530 [thread overview]
Message-ID: <efe976be-79b9-1f1b-69a1-18dd3b0798df@quicinc.com> (raw)
In-Reply-To: <8b9ed619-8ff1-53f1-1f3a-c10a3585b9c4@quicinc.com>
On 1/26/2023 10:20 PM, Kathiravan Thirumoorthy wrote:
> Thanks Konrad for taking time to review the patch.
>
>
> On 1/26/2023 3:29 AM, Konrad Dybcio wrote:
>>
>> On 25.01.2023 11:45, Kathiravan Thirumoorthy wrote:
>>> From: Kathiravan T <quic_kathirav@quicinc.com>
>>>
>>> Add initial device tree support for the Qualcomm IPQ5332 SoC and
>>> MI01.2 board.
>>>
>>> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
>>> ---
>>> arch/arm64/boot/dts/qcom/Makefile | 1 +
>>> arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts | 71 +++++
>>> arch/arm64/boot/dts/qcom/ipq5332.dtsi | 273
>>> ++++++++++++++++++++
>>> 3 files changed, 345 insertions(+)
>>> create mode 100644 arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
>>> create mode 100644 arch/arm64/boot/dts/qcom/ipq5332.dtsi
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/Makefile
>>> b/arch/arm64/boot/dts/qcom/Makefile
>>> index 3e79496292e7..fbd5bc583a9b 100644
>>> --- a/arch/arm64/boot/dts/qcom/Makefile
>>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>>> @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) +=
>>> apq8094-sony-xperia-kitakami-karin_windy.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
>>> +dtb-$(CONFIG_ARCH_QCOM) += ipq5332-mi01.2.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb
>>> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb
>>> diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
>>> b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
>>> new file mode 100644
>>> index 000000000000..7984d8f824ce
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
>>> @@ -0,0 +1,71 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
>>> +/*
>>> + * IPQ5332 AP-MI01.2 board device tree source
>>> + *
>>> + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All
>>> rights reserved.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +#include "ipq5332.dtsi"
>>> +
>>> +/ {
>>> + model = "Qualcomm Technologies, Inc. IPQ5332/AP-MI01.2";
>>> + compatible = "qcom,ipq5332-ap-mi01.2", "qcom,ipq5332";
>>> +
>>> + aliases {
>>> + serial0 = &blsp1_uart0;
>>> + };
>>> +
>>> + chosen {
>>> + stdout-path = "serial0";
>>> + };
>>> +};
>>> +
>>> +&blsp1_uart0 {
>>> + pinctrl-0 = <&serial_0_pins>;
>>> + pinctrl-names = "default";
>>> + status = "okay";
>>> +};
>>> +
>>> +&sdhc {
>>> + pinctrl-0 = <&sdc_default_state>;
>>> + pinctrl-names = "default";
>>> + non-removable;
>>> + status = "okay";
>>> +};
>>> +
>>> +&sleep_clk {
>>> + clock-frequency = <32000>;
>>> +};
>>> +
>>> +&xo_board {
>>> + clock-frequency = <24000000>;
>>> +};
>>> +
>>> +/* PINCTRL */
>>> +
>>> +&tlmm {
>>> + sdc_default_state: sdc-default-state {
>>> + clk-pins {
>>> + pins = "gpio13";
>>> + function = "sdc_clk";
>>> + drive-strength = <8>;
>>> + bias-disable;
>>> + };
>>> +
>>> + cmd-pins {
>>> + pins = "gpio12";
>>> + function = "sdc_cmd";
>>> + drive-strength = <8>;
>>> + bias-pull-up;
>>> + };
>>> +
>>> + data-pins {
>>> + pins = "gpio8", "gpio9", "gpio10", "gpio11";
>>> + function = "sdc_data";
>>> + drive-strength = <8>;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +};
>>> diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi
>>> b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
>>> new file mode 100644
>>> index 000000000000..d04244a3cd3a
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
>>> @@ -0,0 +1,273 @@
>>> +// SPDX-License-Identifier: BSD-3-Clause
>>> +/*
>>> + * IPQ5332 device tree source
>>> + *
>>> + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All
>>> rights reserved.
>>> + */
>>> +
>>> +#include <dt-bindings/clock/qcom,gcc-ipq5332.h>
>>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>>> +
>>> +/ {
>>> + interrupt-parent = <&intc>;
>>> + #address-cells = <2>;
>>> + #size-cells = <2>;
>>> +
>>> + clocks {
>>> + sleep_clk: sleep-clk {
>>> + compatible = "fixed-clock";
>>> + #clock-cells = <0>;
>>> + };
>>> +
>>> + xo_board: xo-board-clk {
>>> + compatible = "fixed-clock";
>>> + #clock-cells = <0>;
>>> + };
>>> + };
>>> +
>>> + cpus {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + CPU0: cpu@0 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a53";
>>> + reg = <0x0>;
>>> + enable-method = "psci";
>>> + next-level-cache = <&L2_0>;
>>> + };
>>> +
>>> + CPU1: cpu@1 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a53";
>>> + reg = <0x1>;
>>> + enable-method = "psci";
>>> + next-level-cache = <&L2_0>;
>>> + };
>>> +
>>> + CPU2: cpu@2 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a53";
>>> + reg = <0x2>;
>>> + enable-method = "psci";
>>> + next-level-cache = <&L2_0>;
>>> + };
>>> +
>>> + CPU3: cpu@3 {
>>> + device_type = "cpu";
>>> + compatible = "arm,cortex-a53";
>>> + reg = <0x3>;
>>> + enable-method = "psci";
>>> + next-level-cache = <&L2_0>;
>>> + };
>>> +
>>> + L2_0: l2-cache {
>>> + compatible = "cache";
>>> + cache-level = <0x2>;
>>> + };
>>> + };
>>> +
>>> + firmware {
>>> + scm {
>>> + compatible = "qcom,scm-ipq5332", "qcom,scm";
>>> + };
>>> + };
>>> +
>>> + memory@40000000 {
>>> + device_type = "memory";
>>> + /* We expect the bootloader to fill in the size */
>>> + reg = <0x0 0x40000000 0x0 0x0>;
>>> + };
>>> +
>>> + pmu {
>>> + compatible = "arm,cortex-a53-pmu";
>>> + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
>>> IRQ_TYPE_LEVEL_HIGH)>;
>>> + };
>>> +
>>> + psci {
>>> + compatible = "arm,psci-1.0";
>>> + method = "smc";
>>> + };
>>> +
>>> + reserved-memory {
>>> + #address-cells = <2>;
>>> + #size-cells = <2>;
>>> + ranges;
>>> +
>>> + tz: memory@4a600000 {
>> memory@ is discouraged, the node name should be somewhat
>> descriptive of what lies in this reserved region. On the
>> other hand, tz: sounds like a label to a trust zone device
>> of some kind. I propose:
>>
>> tz_mem: tz@4a600000 {
>>
>> instead.
>
>
> Ack.
>
>
>>
>>> + no-map;
>>> + reg = <0x0 0x4a600000 0x0 0x200000>;
>>> + };
>>> + };
>>> +
>>> + soc@0 {
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + ranges = <0 0 0 0xffffffff>;
>>> + compatible = "simple-bus";
>> Move compatible first, please.
>
>
> Ack.
>
>
>>
>>> +
>>> + tlmm: pinctrl@1000000 {
>>> + compatible = "qcom,ipq5332-tlmm";
>>> + reg = <0x01000000 0x300000>;
>>> + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
>>> + gpio-controller;
>>> + #gpio-cells = <2>;
>>> + gpio-ranges = <&tlmm 0 0 53>;
>>> + interrupt-controller;
>>> + #interrupt-cells = <2>;
>>> +
>>> + serial_0_pins: serial0-state {
>> You may be interested in having a suspend state for this
>> one, so you may wish to rename this futureproofing-ly to
>> serial0-active-state.
>
>
> Ack. AFAIK, we don't support suspend state, anyways let me got back
> and check it.
Konrad, we don't support the suspend state for the console UART, so left
the node name as it is in V2.
>
>
>>
>>> + pins = "gpio18", "gpio19";
>>> + function = "blsp0_uart0";
>>> + drive-strength = <8>;
>>> + bias-pull-up;
>>> + };
>>> + };
>>> +
>>> + gcc: clock-controller@1800000 {
>>> + compatible = "qcom,ipq5332-gcc";
>>> + reg = <0x01800000 0x80000>;
>>> + #clock-cells = <0x1>;
>>> + #reset-cells = <0x1>;
>> Decimal values for -cells, please.
>
>
> Ack.
>
>
>>
>>> + #power-domain-cells = <1>;
>>> + clock-names = "xo",
>>> + "sleep_clk",
>>> + "pcie_2lane_phy_pipe_clk",
>>> + "pcie_2lane_phy_pipe_clk_x1",
>>> + "usb_pcie_wrapper_pipe_clk";
>>> + clocks = <&xo_board>,
>>> + <&sleep_clk>,
>>> + <0>,
>>> + <0>,
>>> + <0>;
>>> + };
>>> +
>>> + sdhc: mmc@7804000 {
>>> + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5";
>>> + reg = <0x07804000 0x1000>, <0x07805000 0x1000>;
>>> +
>>> + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>;
>>> + interrupt-names = "hc_irq", "pwr_irq";
>>> +
>>> + clocks = <&gcc GCC_SDCC1_AHB_CLK>,
>>> + <&gcc GCC_SDCC1_APPS_CLK>,
>>> + <&xo_board>;
>>> + clock-names = "iface", "core", "xo";
>>> + mmc-ddr-1_8v;
>>> + mmc-hs200-1_8v;
>>> + max-frequency = <192000000>;
>> As Krzysztof pointed out, this one should go.
>
>
> Ack.
Krzysztof & Konrad,
These are the properties of the SDHC controller present in the SoC. So I
think no need to move out these properties to board DTS. Please let me
know if my understanding is otherwise.
>
>
>>
>>> + bus-width = <4>;
>> Oh that's interesting.. a 4-wide bus for eMMC?
>
>
> Yes, eMMC is 4bit bus width with HS200 mode only.
>
>
>>
>>> + status = "disabled";
>>> + };
>>> +
>>> + blsp1_uart0: serial@78af000 {
>>> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
>>> + reg = <0x078af000 0x200>;
>>> + interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
>>> + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
>>> + <&gcc GCC_BLSP1_AHB_CLK>;
>>> + clock-names = "core", "iface";
>>> + status = "disabled";
>>> + };
>>> +
>>> + intc: interrupt-controller@b000000 {
>>> + compatible = "qcom,msm-qgic2";
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>> Please move these two above ranges..
>
>
> Ack.
>
>
>>
>>> + interrupt-controller;
>>> + #interrupt-cells = <0x3>;
>> Decimal value, please.
>
>
> Ack.
>
>
>>
>>> + reg = <0x0b000000 0x1000>, /* GICD */
>>> + <0x0b002000 0x1000>, /* GICC */
>>> + <0x0b001000 0x1000>, /* GICH */
>>> + <0x0b004000 0x1000>; /* GICV */
>> ..and reg just below compatible...
>
> Ack.
>
>
>>
>>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> ..and interrupts just below reg, please.
>
> Ack.
>
>
>>
>>> + ranges = <0 0x0b00c000 0x3000>;
>>> +
>>> + v2m0: v2m@0 {
>>> + compatible = "arm,gic-v2m-frame";
>>> + reg = <0x0 0xffd>;
>> Please pad the reg for consistency.
>
>
> Sure.
>
>
>>> + msi-controller;
>>> + };
>>> +
>>> + v2m1: v2m@1 {
>>> + compatible = "arm,gic-v2m-frame";
>>> + reg = <0x00001000 0xffd>;
>>> + msi-controller;
>>> + };
>>> +
>>> + v2m2: v2m@2 {
>>> + compatible = "arm,gic-v2m-frame";
>>> + reg = <0x00002000 0xffd>;
>>> + msi-controller;
>>> + };
>>> + };
>>> +
>>> + timer@b120000 {
>>> + compatible = "arm,armv7-timer-mem";
>>> + reg = <0x0b120000 0x1000>;
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + ranges;
>>> +
>>> + frame@b120000 {
>>> + frame-number = <0>;
>>> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
>>> + reg = <0x0b121000 0x1000>,
>>> + <0x0b122000 0x1000>;
>> reg
>> interrupts
>> frame-number
>>
>> would be more consistent with most other nodes.
> Ack.
>>
>>> + };
>>> +
>>> + frame@b123000 {
>>> + frame-number = <1>;
>>> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>>> + reg = <0x0b123000 0x1000>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + frame@b124000 {
>>> + frame-number = <2>;
>>> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>>> + reg = <0x0b124000 0x1000>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + frame@b125000 {
>>> + frame-number = <3>;
>>> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
>>> + reg = <0x0b125000 0x1000>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + frame@b126000 {
>>> + frame-number = <4>;
>>> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>>> + reg = <0x0b126000 0x1000>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + frame@b127000 {
>>> + frame-number = <5>;
>>> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>>> + reg = <0x0b127000 0x1000>;
>>> + status = "disabled";
>>> + };
>>> +
>>> + frame@b128000 {
>>> + frame-number = <6>;
>>> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>>> + reg = <0x0b128000 0x1000>;
>>> + status = "disabled";
>>> + };
>>> + };
>>> +
>>> + };
>>> +
>>> + timer {
>>> + compatible = "arm,armv8-timer";
>>> + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) |
>>> IRQ_TYPE_LEVEL_LOW)>,
>>> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) |
>>> IRQ_TYPE_LEVEL_LOW)>,
>>> + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) |
>>> IRQ_TYPE_LEVEL_LOW)>,
>>> + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) |
>>> IRQ_TYPE_LEVEL_LOW)>;
>> The indentation seems off here.
>
>
> Will fix it in V2. Thanks.
>
>
>>
>> Konrad
>>> + };
>>> +};
next prev parent reply other threads:[~2023-01-30 11:57 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-25 10:45 [PATCH 00/10] Add minimal boot support for IPQ5332 Kathiravan Thirumoorthy
2023-01-25 10:45 ` [PATCH 01/10] dt-bindings: pinctrl: qcom: add IPQ5332 pinctrl Kathiravan Thirumoorthy
2023-01-25 11:10 ` Krzysztof Kozlowski
2023-01-25 15:49 ` Kathiravan Thirumoorthy
2023-01-25 16:20 ` Krzysztof Kozlowski
2023-01-25 16:38 ` Kathiravan Thirumoorthy
2023-01-25 10:45 ` [PATCH 02/10] pinctrl: qcom: Introduce IPQ5332 TLMM driver Kathiravan Thirumoorthy
2023-01-25 10:45 ` [PATCH 03/10] clk: qcom: Add STROMER PLUS PLL type for IPQ5332 Kathiravan Thirumoorthy
2023-01-25 20:35 ` Stephen Boyd
2023-01-25 10:45 ` [PATCH 04/10] dt-bindings: clock: Add Qualcomm IPQ5332 GCC Kathiravan Thirumoorthy
2023-01-25 11:13 ` Krzysztof Kozlowski
2023-01-25 15:50 ` Kathiravan Thirumoorthy
2023-01-25 10:45 ` [PATCH 05/10] clk: qcom: add Global Clock controller (GCC) driver for IPQ5332 SoC Kathiravan Thirumoorthy
2023-01-25 11:14 ` Krzysztof Kozlowski
2023-01-25 15:53 ` Kathiravan Thirumoorthy
2023-01-25 20:54 ` Stephen Boyd
2023-01-26 16:45 ` Kathiravan Thirumoorthy
2023-01-25 10:45 ` [PATCH 06/10] dt-bindings: qcom: add ipq5332 boards Kathiravan Thirumoorthy
2023-01-25 11:15 ` Krzysztof Kozlowski
2023-01-25 15:55 ` Kathiravan Thirumoorthy
2023-01-25 10:45 ` [PATCH 07/10] dt-bindings: firmware: document IPQ5332 SCM Kathiravan Thirumoorthy
2023-01-25 11:16 ` Krzysztof Kozlowski
2023-01-25 15:55 ` Kathiravan Thirumoorthy
2023-01-25 10:45 ` [PATCH 08/10] dt-bindings: mmc: sdhci-msm: add IPQ5332 compatible Kathiravan Thirumoorthy
2023-01-25 11:17 ` Krzysztof Kozlowski
2023-01-27 10:56 ` Ulf Hansson
2023-01-25 10:45 ` [PATCH 09/10] arm64: dts: qcom: add IPQ5332 SoC and MI01.2 board support Kathiravan Thirumoorthy
2023-01-25 11:22 ` Krzysztof Kozlowski
2023-01-25 16:05 ` Kathiravan Thirumoorthy
2023-01-25 21:59 ` Konrad Dybcio
2023-01-26 16:50 ` Kathiravan Thirumoorthy
2023-01-30 11:56 ` Kathiravan Thirumoorthy [this message]
2023-01-31 19:24 ` Krzysztof Kozlowski
2023-01-25 10:45 ` [PATCH 10/10] arm64: defconfig: Enable IPQ5332 SoC base configs Kathiravan Thirumoorthy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=efe976be-79b9-1f1b-69a1-18dd3b0798df@quicinc.com \
--to=quic_kathirav@quicinc.com \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=arnd@arndb.de \
--cc=bhupesh.sharma@linaro.org \
--cc=broonie@kernel.org \
--cc=catalin.marinas@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@linaro.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=marcel.ziswiler@toradex.com \
--cc=mturquette@baylibre.com \
--cc=nfraprado@collabora.com \
--cc=quic_gurus@quicinc.com \
--cc=robh+dt@kernel.org \
--cc=robimarko@gmail.com \
--cc=sboyd@kernel.org \
--cc=shawnguo@kernel.org \
--cc=ulf.hansson@linaro.org \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).