[PATCH v1 0/4] thermal: tsens: Add support for QCS404 platform

[PATCH v1 0/4] thermal: tsens: Add support for QCS404 platform

[Amit Kucheria]

Add support for the Qualcomm QCS404 platform that contains v1 of the TSENS
IP. Introduce a fallback binding to handle "v1" functionality.

These patches apply on top of previous tsens-related patches sent to the
list pending merge along with various qcs404 patches under review
(available in this branch[1] for convenience).

[1] https://git.linaro.org/landing-teams/working/qualcomm/kernel.git/log/?h=integration-linux-qcomlt

Amit Kucheria (4):
  dt: thermal: tsens: Add bindings for qcs404
  drivers: thermal: tsens: Add generic support for TSENS v1 IP
  arm64: dts: qcom: qcs404: Add tsens controller
  arm64: dts: qcom: qcs404: Add thermal zones for each sensor

 .../bindings/thermal/qcom-tsens.txt           |   3 +
 arch/arm64/boot/dts/qcom/qcs404.dtsi          | 226 ++++++++++++++++++
 drivers/thermal/qcom/Makefile                 |   2 +-
 drivers/thermal/qcom/tsens-v1.c               | 196 +++++++++++++++
 drivers/thermal/qcom/tsens.c                  |   3 +
 drivers/thermal/qcom/tsens.h                  |   2 +-
 6 files changed, 430 insertions(+), 2 deletions(-)
 create mode 100644 drivers/thermal/qcom/tsens-v1.c

-- 
2.17.1

[PATCH v1 1/4] dt: thermal: tsens: Add bindings for qcs404

[Amit Kucheria]

qcs404 uses v1 of the TSENS IP block. Create a fallback DT property
"qcom,tsens-v1" to gather common code.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 Documentation/devicetree/bindings/thermal/qcom-tsens.txt | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
index 1d9e8cf61018..799de3062352 100644
--- a/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
+++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.txt
@@ -8,9 +8,12 @@ Required properties:
     - "qcom,msm8996-tsens" (MSM8996)
     - "qcom,msm8998-tsens", "qcom,tsens-v2" (MSM8998)
     - "qcom,sdm845-tsens", "qcom,tsens-v2" (SDM845)
+    - "qcom,qcs404-tsens", "qcom,tsens-v1" (QCS404)
   The generic "qcom,tsens-v2" property must be used as a fallback for any SoC
   with version 2 of the TSENS IP. MSM8996 is the only exception because the
   generic property did not exist when support was added.
+  Similarly, the generic "qcom,tsens-v1" property must be used as a fallback for
+  any SoC with version 1 of the TSENS IP.
 
 - reg: Address range of the thermal registers.
   New platforms containing v2.x.y of the TSENS IP must specify the SROT and TM
-- 
2.17.1

[PATCH v1 2/4] drivers: thermal: tsens: Add generic support for TSENS v1 IP

[Amit Kucheria]

qcs404 has a single TSENS IP block with 10 sensors. It uses version 1.4
of the TSENS IP, functionality for which is encapsulated inside
qcom,tsens-v1 compatible.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/Makefile   |   2 +-
 drivers/thermal/qcom/tsens-v1.c | 196 ++++++++++++++++++++++++++++++++
 drivers/thermal/qcom/tsens.c    |   3 +
 drivers/thermal/qcom/tsens.h    |   2 +-
 4 files changed, 201 insertions(+), 2 deletions(-)
 create mode 100644 drivers/thermal/qcom/tsens-v1.c

diff --git a/drivers/thermal/qcom/Makefile b/drivers/thermal/qcom/Makefile
index a821929ede0b..60269ee90c43 100644
--- a/drivers/thermal/qcom/Makefile
+++ b/drivers/thermal/qcom/Makefile
@@ -1,2 +1,2 @@
 obj-$(CONFIG_QCOM_TSENS)	+= qcom_tsens.o
-qcom_tsens-y			+= tsens.o tsens-common.o tsens-8916.o tsens-8974.o tsens-8960.o tsens-v2.o
+qcom_tsens-y			+= tsens.o tsens-common.o tsens-8916.o tsens-8974.o tsens-8960.o tsens-v2.o tsens-v1.o
diff --git a/drivers/thermal/qcom/tsens-v1.c b/drivers/thermal/qcom/tsens-v1.c
new file mode 100644
index 000000000000..297bcac3b94e
--- /dev/null
+++ b/drivers/thermal/qcom/tsens-v1.c
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, Linaro Limited
+ */
+
+#include <linux/regmap.h>
+#include <linux/bitops.h>
+#include "tsens.h"
+
+/* eeprom layout data for qcs404 (v1) */
+#define BASE0_MASK	0x000007f8
+#define BASE1_MASK	0x0007f800
+#define BASE0_SHIFT	3
+#define BASE1_SHIFT	11
+
+#define S0_P1_MASK	0x0000003f
+#define S1_P1_MASK	0x0003f000
+#define S2_P1_MASK	0x3f000000
+#define S3_P1_MASK	0x000003f0
+#define S4_P1_MASK	0x003f0000
+#define S5_P1_MASK	0x0000003f
+#define S6_P1_MASK	0x0003f000
+#define S7_P1_MASK	0x3f000000
+#define S8_P1_MASK	0x000003f0
+#define S9_P1_MASK	0x003f0000
+
+#define S0_P2_MASK	0x00000fc0
+#define S1_P2_MASK	0x00fc0000
+#define S2_P2_MASK_1_0	0xc0000000
+#define S2_P2_MASK_5_2	0x0000000f
+#define S3_P2_MASK	0x0000fc00
+#define S4_P2_MASK	0x0fc00000
+#define S5_P2_MASK	0x00000fc0
+#define S6_P2_MASK	0x00fc0000
+#define S7_P2_MASK_1_0	0xc0000000
+#define S7_P2_MASK_5_2	0x0000000f
+#define S8_P2_MASK	0x0000fc00
+#define S9_P2_MASK	0x0fc00000
+
+#define S0_P1_SHIFT	0
+#define S0_P2_SHIFT	6
+#define S1_P1_SHIFT	12
+#define S1_P2_SHIFT	18
+#define S2_P1_SHIFT	24
+#define S2_P2_SHIFT_1_0	30
+
+#define S2_P2_SHIFT_5_2	0
+#define S3_P1_SHIFT	4
+#define S3_P2_SHIFT	10
+#define S4_P1_SHIFT	16
+#define S4_P2_SHIFT	22
+
+#define S5_P1_SHIFT	0
+#define S5_P2_SHIFT	6
+#define S6_P1_SHIFT	12
+#define S6_P2_SHIFT	18
+#define S7_P1_SHIFT	24
+#define S7_P2_SHIFT_1_0	30
+
+#define S7_P2_SHIFT_5_2	0
+#define S8_P1_SHIFT	4
+#define S8_P2_SHIFT	10
+#define S9_P1_SHIFT	16
+#define S9_P2_SHIFT	22
+
+#define CAL_SEL_MASK	7
+#define CAL_SEL_SHIFT	0
+
+static int calibrate_v1(struct tsens_device *tmdev)
+{
+	u32 base0 = 0, base1 = 0;
+	u32 p1[tmdev->num_sensors], p2[tmdev->num_sensors];
+	u32 mode = 0, lsb = 0, msb = 0;
+	u32 *qfprom_cdata;
+	int i;
+
+	qfprom_cdata = (u32 *)qfprom_read(tmdev->dev, "calib");
+	if (IS_ERR(qfprom_cdata))
+		return PTR_ERR(qfprom_cdata);
+
+	mode = (qfprom_cdata[4] & CAL_SEL_MASK) >> CAL_SEL_SHIFT;
+	dev_dbg(tmdev->dev, "calibration mode is %d\n", mode);
+
+	switch (mode) {
+	case TWO_PT_CALIB:
+		base1 = (qfprom_cdata[4] & BASE1_MASK) >> BASE1_SHIFT;
+		p2[0] = (qfprom_cdata[0] & S0_P2_MASK) >> S0_P2_SHIFT;
+		p2[1] = (qfprom_cdata[0] & S1_P2_MASK) >> S1_P2_SHIFT;
+		/* This value is split over two registers, 2 bits and 4 bits */
+		lsb   = (qfprom_cdata[0] & S2_P2_MASK_1_0) >> S2_P2_SHIFT_1_0;
+		msb   = (qfprom_cdata[1] & S2_P2_MASK_5_2) >> S2_P2_SHIFT_5_2;
+		p2[2] = msb << 2 | lsb;
+		p2[3] = (qfprom_cdata[1] & S3_P2_MASK) >> S3_P2_SHIFT;
+		p2[4] = (qfprom_cdata[1] & S4_P2_MASK) >> S4_P2_SHIFT;
+		p2[5] = (qfprom_cdata[2] & S5_P2_MASK) >> S5_P2_SHIFT;
+		p2[6] = (qfprom_cdata[2] & S6_P2_MASK) >> S6_P2_SHIFT;
+		/* This value is split over two registers, 2 bits and 4 bits */
+		lsb   = (qfprom_cdata[2] & S7_P2_MASK_1_0) >> S7_P2_SHIFT_1_0;
+		msb   = (qfprom_cdata[3] & S7_P2_MASK_5_2) >> S7_P2_SHIFT_5_2;
+		p2[7] = msb << 2 | lsb;
+		p2[8] = (qfprom_cdata[3] & S8_P2_MASK) >> S8_P2_SHIFT;
+		p2[9] = (qfprom_cdata[3] & S9_P2_MASK) >> S9_P2_SHIFT;
+		for (i = 0; i < tmdev->num_sensors; i++)
+			p2[i] = ((base1 + p2[i]) << 2);
+		/* Fall through */
+	case ONE_PT_CALIB2:
+		base0 = (qfprom_cdata[4] & BASE0_MASK) >> BASE0_SHIFT;
+		p1[0] = (qfprom_cdata[0] & S0_P1_MASK) >> S0_P1_SHIFT;
+		p1[1] = (qfprom_cdata[0] & S1_P1_MASK) >> S1_P1_SHIFT;
+		p1[2] = (qfprom_cdata[0] & S2_P1_MASK) >> S2_P1_SHIFT;
+		p1[3] = (qfprom_cdata[1] & S3_P1_MASK) >> S3_P1_SHIFT;
+		p1[4] = (qfprom_cdata[1] & S4_P1_MASK) >> S4_P1_SHIFT;
+		p1[5] = (qfprom_cdata[2] & S5_P1_MASK) >> S5_P1_SHIFT;
+		p1[6] = (qfprom_cdata[2] & S6_P1_MASK) >> S6_P1_SHIFT;
+		p1[7] = (qfprom_cdata[2] & S7_P1_MASK) >> S7_P1_SHIFT;
+		p1[8] = (qfprom_cdata[3] & S8_P1_MASK) >> S8_P1_SHIFT;
+		p1[9] = (qfprom_cdata[3] & S9_P1_MASK) >> S9_P1_SHIFT;
+		for (i = 0; i < tmdev->num_sensors; i++)
+			p1[i] = (((base0) + p1[i]) << 2);
+		break;
+	default:
+		for (i = 0; i < tmdev->num_sensors; i++) {
+			p1[i] = 500;
+			p2[i] = 780;
+		}
+		break;
+	}
+
+	compute_intercept_slope(tmdev, p1, p2, mode);
+
+	return 0;
+}
+
+#define STATUS_OFFSET		0x44
+#define LAST_TEMP_MASK		0x3ff
+#define STATUS_VALID_BIT	BIT(14)
+
+static int get_temp_tsens_v1(struct tsens_device *tmdev, int id, int *temp)
+{
+	struct tsens_sensor *s = &tmdev->sensor[id];
+	u32 code;
+	unsigned int status_reg;
+	u32 last_temp = 0, last_temp2 = 0, last_temp3 = 0;
+	int ret;
+
+	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * 4;
+	ret = regmap_read(tmdev->tm_map, status_reg, &code);
+	if (ret)
+		return ret;
+	last_temp = code & LAST_TEMP_MASK;
+	if (code & STATUS_VALID_BIT)
+		goto done;
+
+	/* Try a second time */
+	ret = regmap_read(tmdev->tm_map, status_reg, &code);
+	if (ret)
+		return ret;
+	if (code & STATUS_VALID_BIT) {
+		last_temp = code & LAST_TEMP_MASK;
+		goto done;
+	} else {
+		last_temp2 = code & LAST_TEMP_MASK;
+	}
+
+	/* Try a third/last time */
+	ret = regmap_read(tmdev->tm_map, status_reg, &code);
+	if (ret)
+		return ret;
+	if (code & STATUS_VALID_BIT) {
+		last_temp = code & LAST_TEMP_MASK;
+		goto done;
+	} else {
+		last_temp3 = code & LAST_TEMP_MASK;
+	}
+
+	if (last_temp == last_temp2)
+		last_temp = last_temp2;
+	else if (last_temp2 == last_temp3)
+		last_temp = last_temp3;
+done:
+	/* Convert temperature from deciCelsius to milliCelsius */
+	*temp = sign_extend32(last_temp, fls(LAST_TEMP_MASK) - 1) * 100;
+
+	return 0;
+}
+
+static const struct tsens_ops ops_generic_v1 = {
+	.init		= init_common,
+	.calibrate	= calibrate_v1,
+	.get_temp	= get_temp_tsens_v1,
+};
+
+const struct tsens_data data_tsens_v1 = {
+	.ops		= &ops_generic_v1,
+	.reg_offsets	= { [SROT_CTRL_OFFSET] = 0x4 },
+};
diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
index f1ec9bbe4717..d0cc0c09894a 100644
--- a/drivers/thermal/qcom/tsens.c
+++ b/drivers/thermal/qcom/tsens.c
@@ -63,6 +63,9 @@ static const struct of_device_id tsens_table[] = {
 	}, {
 		.compatible = "qcom,msm8996-tsens",
 		.data = &data_8996,
+	}, {
+		.compatible = "qcom,tsens-v1",
+		.data = &data_tsens_v1,
 	}, {
 		.compatible = "qcom,tsens-v2",
 		.data = &data_tsens_v2,
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index 7b7feee5dc46..7060c22ea611 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -92,7 +92,7 @@ int init_common(struct tsens_device *);
 int get_temp_common(struct tsens_device *, int, int *);
 
 /* TSENS v1 targets */
-extern const struct tsens_data data_8916, data_8974, data_8960;
+extern const struct tsens_data data_8916, data_8974, data_8960, data_tsens_v1;
 /* TSENS v2 targets */
 extern const struct tsens_data data_8996, data_tsens_v2;
 
-- 
2.17.1

[PATCH v1 3/4] arm64: dts: qcom: qcs404: Add tsens controller

[Amit Kucheria]

qcs404 has a single TSENS IP block with 10 sensors. The calibration data
is stored in an eeprom (qfprom) that is accessed through the nvmem
framework. We add the qfprom node to allow the tsens sensors to be
calibrated correctly.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404.dtsi | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index e1e2ba9cbfcd..dfd65c53cf5f 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -273,6 +273,26 @@
 			status = "okay";
 		};
 
+		qfprom: qfprom@a4000 {
+			compatible = "qcom,qfprom";
+			reg = <0xa4000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			tsens_caldata: caldata@d0 {
+				reg = <0x1f8 0x14>;
+			};
+		};
+
+		tsens: thermal-sensor@4a9000 {
+			compatible = "qcom,qcs404-tsens", "qcom,tsens-v1";
+			reg = <0x4a9000 0x1000>, /* TM */
+			      <0x4a8000 0x1000>; /* SROT */
+			nvmem-cells = <&tsens_caldata>;
+			nvmem-cell-names = "calib";
+			#qcom,sensors = <10>;
+			#thermal-sensor-cells = <1>;
+		};
+
 		apcs_glb: mailbox@b011000 {
 			compatible = "qcom,qcs404-apcs-apps-global", "syscon";
 			reg = <0xb011000 0x1000>;
-- 
2.17.1

[PATCH v1 4/4] arm64: dts: qcom: qcs404: Add thermal zones for each sensor

[Amit Kucheria]

qcs404 has 10 sensors connected to the single TSENS IP. Define a thermal
zone for each of those sensors to expose the temperature of each zone.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404.dtsi | 206 +++++++++++++++++++++++++++
 1 file changed, 206 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index dfd65c53cf5f..ea882a9ce6e3 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -69,6 +69,7 @@
 			reg = <0x100>;
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
+			#cooling-cells= <2>;
 		};
 
 		CPU1: cpu@1 {
@@ -77,6 +78,7 @@
 			reg = <0x101>;
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
+			#cooling-cells= <2>;
 		};
 
 		CPU2: cpu@2 {
@@ -85,6 +87,7 @@
 			reg = <0x102>;
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
+			#cooling-cells= <2>;
 		};
 
 		CPU3: cpu@3 {
@@ -93,6 +96,7 @@
 			reg = <0x100>;
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
+			#cooling-cells= <2>;
 		};
 
 		L2_0: l2-cache {
@@ -484,4 +488,206 @@
 			label = "wcss";
 		};
 	};
+
+	thermal-zones {
+		aoss-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 0>;
+
+			trips {
+				aoss_alert: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				aoss_crit: trip1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		dsp-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				dsp_alert: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				dsp_crit: trip1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		lpass-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				lpass_alert: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				lpass_crit: trip1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		wlan-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				wlan_alert: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				wlan_crit: trip1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cluster-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				cluster_alert: cluster_alert {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cluster_crit: cluster_crit {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal0 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu_alert0: cpu_alert0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: cpu_crit0 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal1 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal2 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu_alert2: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit2: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal3 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu_alert3: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit3: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		gpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				gpu_alert: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				gpu_crit: trip1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
 };
-- 
2.17.1

Re: [PATCH v1 0/4] thermal: tsens: Add support for QCS404 platform

[Vinod]

On 16-10-18, 00:10, Amit Kucheria wrote:
> Add support for the Qualcomm QCS404 platform that contains v1 of the TSENS
> IP. Introduce a fallback binding to handle "v1" functionality.


Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>

-- 
~Vinod

Re: [PATCH v1 3/4] arm64: dts: qcom: qcs404: Add tsens controller

[Vinod Koul]

On 16-10-18, 00:10, Amit Kucheria wrote:
> qcs404 has a single TSENS IP block with 10 sensors. The calibration data
> is stored in an eeprom (qfprom) that is accessed through the nvmem
> framework. We add the qfprom node to allow the tsens sensors to be
> calibrated correctly.

Andy,

These have dependency on the patch series adding The DT file I sent
yesterday[1]. Please apply these on top of that series

[1]: https://patchwork.kernel.org/project/linux-arm-msm/list/?series=36319

Thanks

> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/qcs404.dtsi | 20 ++++++++++++++++++++
>  1 file changed, 20 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
> index e1e2ba9cbfcd..dfd65c53cf5f 100644
> --- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
> @@ -273,6 +273,26 @@
>  			status = "okay";
>  		};
>  
> +		qfprom: qfprom@a4000 {
> +			compatible = "qcom,qfprom";
> +			reg = <0xa4000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			tsens_caldata: caldata@d0 {
> +				reg = <0x1f8 0x14>;
> +			};
> +		};
> +
> +		tsens: thermal-sensor@4a9000 {
> +			compatible = "qcom,qcs404-tsens", "qcom,tsens-v1";
> +			reg = <0x4a9000 0x1000>, /* TM */
> +			      <0x4a8000 0x1000>; /* SROT */
> +			nvmem-cells = <&tsens_caldata>;
> +			nvmem-cell-names = "calib";
> +			#qcom,sensors = <10>;
> +			#thermal-sensor-cells = <1>;
> +		};
> +
>  		apcs_glb: mailbox@b011000 {
>  			compatible = "qcom,qcs404-apcs-apps-global", "syscon";
>  			reg = <0xb011000 0x1000>;
> -- 
> 2.17.1

-- 
~Vinod