From: Roger Quadros <rogerq@ti.com>
To: <davem@davemloft.net>, Andrew Lunn <andrew@lunn.ch>,
Florian Fainelli <f.fainelli@gmail.com>
Cc: <tony@atomide.com>, <nsekhar@ti.com>, <jsarha@ti.com>,
<netdev@vger.kernel.org>, <linux-omap@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <rogerq@ti.com>
Subject: [PATCH v4 net-next] mdio_bus: Issue GPIO RESET to PHYs.
Date: Fri, 21 Apr 2017 16:15:38 +0300 [thread overview]
Message-ID: <fe0b7ec5-2f83-ba06-579f-3ea0d5c4990c@ti.com> (raw)
In-Reply-To: <f372db02-a919-55b4-9200-20726cd13482@ti.com>
Some boards [1] leave the PHYs at an invalid state
during system power-up or reset thus causing unreliability
issues with the PHY which manifests as PHY not being detected
or link not functional. To fix this, these PHYs need to be RESET
via a GPIO connected to the PHY's RESET pin.
Some boards have a single GPIO controlling the PHY RESET pin of all
PHYs on the bus whereas some others have separate GPIOs controlling
individual PHY RESETs.
In both cases, the RESET de-assertion cannot be done in the PHY driver
as the PHY will not probe till its reset is de-asserted.
So do the RESET de-assertion in the MDIO bus driver.
[1] - am572x-idk, am571x-idk, a437x-idk
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
v4:
- use dev_err() instead of pr_err()
- put PHYs back in RESET on failure or mdiobus_unregister()
- typo fixes uS -> us
v3:
- added more information in the DT binding document.
v2:
- add device tree binding document (mdio.txt)
- specify default reset delay in of_mdio.c instead of mdio_bus.c
Documentation/devicetree/bindings/net/mdio.txt | 33 ++++++++++++++++++
drivers/net/phy/mdio_bus.c | 47 ++++++++++++++++++++++++++
drivers/of/of_mdio.c | 7 ++++
include/linux/phy.h | 7 ++++
4 files changed, 94 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/mdio.txt
diff --git a/Documentation/devicetree/bindings/net/mdio.txt b/Documentation/devicetree/bindings/net/mdio.txt
new file mode 100644
index 0000000..4ffbbac
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mdio.txt
@@ -0,0 +1,33 @@
+Common MDIO bus properties.
+
+These are generic properties that can apply to any MDIO bus.
+
+Optional properties:
+- reset-gpios: List of one or more GPIOs that control the RESET lines
+ of the PHYs on that MDIO bus.
+- reset-delay-us: RESET pulse width in microseconds as per PHY datasheet.
+
+A list of child nodes, one per device on the bus is expected. These
+should follow the generic phy.txt, or a device specific binding document.
+
+Example :
+This example shows these optional properties, plus other properties
+required for the TI Davinci MDIO driver.
+
+ davinci_mdio: ethernet@0x5c030000 {
+ compatible = "ti,davinci_mdio";
+ reg = <0x5c030000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <2>; /* PHY datasheet states 1us min */
+
+ ethphy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ ethphy1: ethernet-phy@3 {
+ reg = <3>;
+ };
+ };
diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c
index fa7d51f..de927f7 100644
--- a/drivers/net/phy/mdio_bus.c
+++ b/drivers/net/phy/mdio_bus.c
@@ -22,8 +22,11 @@
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/device.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/of_device.h>
#include <linux/of_mdio.h>
+#include <linux/of_gpio.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
@@ -307,6 +310,7 @@ int __mdiobus_register(struct mii_bus *bus, struct module *owner)
{
struct mdio_device *mdiodev;
int i, err;
+ struct gpio_desc *gpiod;
if (NULL == bus || NULL == bus->name ||
NULL == bus->read || NULL == bus->write)
@@ -333,6 +337,35 @@ int __mdiobus_register(struct mii_bus *bus, struct module *owner)
if (bus->reset)
bus->reset(bus);
+ /* de-assert bus level PHY GPIO resets */
+ if (bus->num_reset_gpios > 0) {
+ bus->reset_gpiod = devm_kcalloc(&bus->dev,
+ bus->num_reset_gpios,
+ sizeof(struct gpio_desc *),
+ GFP_KERNEL);
+ if (!bus->reset_gpiod)
+ return -ENOMEM;
+ }
+
+ for (i = 0; i < bus->num_reset_gpios; i++) {
+ gpiod = devm_gpiod_get_index(&bus->dev, "reset", i,
+ GPIOD_OUT_LOW);
+ if (IS_ERR(gpiod)) {
+ err = PTR_ERR(gpiod);
+ if (err != -ENOENT) {
+ dev_err(&bus->dev,
+ "mii_bus %s couldn't get reset GPIO\n",
+ bus->id);
+ return err;
+ }
+ } else {
+ bus->reset_gpiod[i] = gpiod;
+ gpiod_set_value_cansleep(gpiod, 1);
+ udelay(bus->reset_delay_us);
+ gpiod_set_value_cansleep(gpiod, 0);
+ }
+ }
+
for (i = 0; i < PHY_MAX_ADDR; i++) {
if ((bus->phy_mask & (1 << i)) == 0) {
struct phy_device *phydev;
@@ -360,6 +393,13 @@ int __mdiobus_register(struct mii_bus *bus, struct module *owner)
mdiodev->device_remove(mdiodev);
mdiodev->device_free(mdiodev);
}
+
+ /* Put PHYs in RESET to save power */
+ for (i = 0; i < bus->num_reset_gpios; i++) {
+ if (bus->reset_gpiod[i])
+ gpiod_set_value_cansleep(bus->reset_gpiod[i], 1);
+ }
+
device_del(&bus->dev);
return err;
}
@@ -381,6 +421,13 @@ void mdiobus_unregister(struct mii_bus *bus)
mdiodev->device_remove(mdiodev);
mdiodev->device_free(mdiodev);
}
+
+ /* Put PHYs in RESET to save power */
+ for (i = 0; i < bus->num_reset_gpios; i++) {
+ if (bus->reset_gpiod[i])
+ gpiod_set_value_cansleep(bus->reset_gpiod[i], 1);
+ }
+
device_del(&bus->dev);
}
EXPORT_SYMBOL(mdiobus_unregister);
diff --git a/drivers/of/of_mdio.c b/drivers/of/of_mdio.c
index 0b29798..7e4c80f 100644
--- a/drivers/of/of_mdio.c
+++ b/drivers/of/of_mdio.c
@@ -22,6 +22,8 @@
#include <linux/of_net.h>
#include <linux/module.h>
+#define DEFAULT_GPIO_RESET_DELAY 10 /* in microseconds */
+
MODULE_AUTHOR("Grant Likely <grant.likely@secretlab.ca>");
MODULE_LICENSE("GPL");
@@ -221,6 +223,11 @@ int of_mdiobus_register(struct mii_bus *mdio, struct device_node *np)
mdio->dev.of_node = np;
+ /* Get bus level PHY reset GPIO details */
+ mdio->reset_delay_us = DEFAULT_GPIO_RESET_DELAY;
+ of_property_read_u32(np, "reset-delay-us", &mdio->reset_delay_us);
+ mdio->num_reset_gpios = of_gpio_named_count(np, "reset-gpios");
+
/* Register the MDIO bus */
rc = mdiobus_register(mdio);
if (rc)
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 43a7748..8ce57f4 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -217,6 +217,13 @@ struct mii_bus {
* matching its address
*/
int irq[PHY_MAX_ADDR];
+
+ /* GPIO reset pulse width in microseconds */
+ int reset_delay_us;
+ /* Number of reset GPIOs */
+ int num_reset_gpios;
+ /* Array of RESET GPIO descriptors */
+ struct gpio_desc **reset_gpiod;
};
#define to_mii_bus(d) container_of(d, struct mii_bus, dev)
--
2.7.4
next prev parent reply other threads:[~2017-04-21 13:16 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-04-05 8:33 [PATCH] net: davinci_mdio: add GPIO reset logic Roger Quadros
2017-04-05 15:03 ` Andrew Lunn
2017-04-06 9:15 ` Roger Quadros
2017-04-06 12:05 ` Andrew Lunn
2017-04-06 16:48 ` Roger Quadros
2017-04-08 13:55 ` David Miller
2017-04-08 15:10 ` Andrew Lunn
2017-04-08 15:18 ` Florian Fainelli
2017-04-10 7:52 ` Roger Quadros
2017-04-19 9:24 ` [PATCH] mdio_bus: Issue GPIO RESET to PHYs Roger Quadros
2017-04-19 11:39 ` Andrew Lunn
2017-04-19 11:56 ` Roger Quadros
2017-04-19 13:38 ` Andrew Lunn
2017-04-20 7:58 ` Roger Quadros
2017-04-20 8:39 ` [PATCH v2] " Roger Quadros
2017-04-20 13:13 ` Andrew Lunn
2017-04-20 13:56 ` Roger Quadros
2017-04-20 14:11 ` [PATCH v3 net-next] " Roger Quadros
2017-04-21 1:12 ` Andrew Lunn
2017-04-21 1:23 ` Florian Fainelli
2017-04-21 1:38 ` Andrew Lunn
2017-04-21 8:04 ` Roger Quadros
2017-04-21 13:15 ` Roger Quadros [this message]
2017-04-21 13:31 ` [PATCH v4 " Lars-Peter Clausen
2017-04-23 23:35 ` Andrew Lunn
2017-04-24 9:04 ` Roger Quadros
2017-04-24 16:32 ` Florian Fainelli
2017-04-25 16:22 ` Lars-Peter Clausen
2017-04-25 16:31 ` Florian Fainelli
2017-04-26 10:46 ` Roger Quadros
2017-04-26 12:27 ` Andrew Lunn
2017-04-26 10:43 ` Roger Quadros
2017-04-24 16:40 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=fe0b7ec5-2f83-ba06-579f-3ea0d5c4990c@ti.com \
--to=rogerq@ti.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=jsarha@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=nsekhar@ti.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).