[PATCH v4 0/7] ARM: davinci: add support for the am1808 based enbw_cmc board

[PATCH v4 0/7] ARM: davinci: add support for the am1808 based enbw_cmc board

[Heiko Schocher]

this patchserie add support for the davinci am1808 based
enbw_cmc board.

changes for v2:
Post this patchserie now as v2, as reworked in the
comments I got for the RFC serie.

changes for v3:
- Interrupt Controller:
  - comment from Sergei Shtylyov:
    - rename compatible" prop to "ti,cp_intc"
    - cp_intc_init() is now also for the of case
      the name of the init function (it calls the
      "new" __cp_intc_init() function, which was
      the "old" cp_intc_init()). Through this
      rework the changes for OF is better visible.
      As the OF case uses the irq_domain rework from
      Grant Likely, maybe the none OF case can use
      this also, but this should be tested on a hw ...

changes for v4:
- Interrupt Controller:
  - split in two patches as Nori Sekhar suggested
    one for the irq_domain change
    one for DT support
  - add comment from Grant Likely for the DT part:
    remove if/else clause, not needed.
    Make use of DT runtime configurable
    The non OF case is not tested!
     
Got no comments to the following points, I noted in the
RFC series, so posting this patchseries with them:

- ARM: davinci: configure davinci aemif chipselects through OF
  not moved to mfd, as mentioned in this discussion:
  http://davinci-linux-open-source.1494791.n2.nabble.com/PATCH-arm-davinci-configure-davinci-aemif-chipselects-through-OF-td7059739.html
  instead use a phandle in the DTS, so drivers which
  uses the davinci aemif, can call davinci_aemif_setup_timing_of()

  This is just thought as an RFC ... The enbw_cmc board
  support not really need to setup this bus timings, as
  they are setup in U-Boot ... but I want to post this,
  as I think, it is a nice to have, and I am not really
  sure, if this has to be a MFD device (If so, all bus
  interfaces for other SoCs should be converted also to
  MFD devices) ... as an example how this can be used
  I add this to the davinci nand controller OF support
  patch, in this patchserie.

- ARM: davinci: mux: add OF support
  I want to get rid of the pin setup code in board code ...
  This patch introduces a davinci_cfg_reg_of() function,
  which davinci drivers can call, if they found a
  "pinmux-handle", so used in the following drivers in
  this patchserie:

  drivers/net/ethernet/ti/davinci_emac
  drivers/i2c/busses/i2c-davinci.c
  drivers/mtd/nand/davinci_nand.c

  This is removed for v4 serie, as Nori Sekhar suggested.

- post this board support with USB support, even though
  USB is only working with the 10 ms "workaround", posted here:
  http://comments.gmane.org/gmane.linux.usb.general/54505
  I see this issue also on the AM1808 TMDXEXP1808L evalboard.

  change for v4:
  The 10 ms delay is no longer needed, see discussion here:

  http://www.spinics.net/lists/linux-usb/msg64232.html

  shows the way to go ...

- MMC and USB are not using OF support yet, ideas how to port
  this are welcome. I need for USB and MMC board specific
  callbacks, how to solve this with OF support?

Signed-off-by: Heiko Schocher <hs-ynQEQJNshbs@public.gmane.org>
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ@public.gmane.org
Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org
Cc: linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: netdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: David Woodhouse <dwmw2-wEGCiKHe2LqWVfeAwA7xHQ@public.gmane.org>
Cc: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
Cc: Wolfram Sang <w.sang-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
Cc: Sekhar Nori <nsekhar-l0cyMroinI0@public.gmane.org>
Cc: Kevin Hilman <khilman-l0cyMroinI0@public.gmane.org>
Cc: Wolfgang Denk <wd-ynQEQJNshbs@public.gmane.org>
Cc: Sergei Shtylyov <sshtylyov-Igf4POYTYCDQT0dZR+AlfA@public.gmane.org>
Cc: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>

Heiko Schocher (7):
  ARM: davinci, intc: Add irq domain support
  ARM: davinci, intc: Add OF support for TI interrupt controller
  ARM: davinci: configure davinci aemif chipselects through OF
  ARM: davinci: net: davinci_emac: add OF support
  ARM: davinci: i2c: add OF support
  ARM: mtd: nand: davinci: add OF support for davinci nand controller
  ARM: davinci: add support for the am1808 based enbw_cmc board

 .../devicetree/bindings/arm/davinci/aemif.txt      |  119 +++++++
 .../devicetree/bindings/arm/davinci/i2c.txt        |   31 ++
 .../devicetree/bindings/arm/davinci/intc.txt       |   27 ++
 .../devicetree/bindings/arm/davinci/nand.txt       |   72 ++++
 .../devicetree/bindings/net/davinci_emac.txt       |   41 +++
 arch/arm/boot/dts/enbw_cmc.dts                     |  172 +++++++++
 arch/arm/configs/enbw_cmc_defconfig                |  123 +++++++
 arch/arm/mach-davinci/Kconfig                      |    9 +
 arch/arm/mach-davinci/Makefile                     |    1 +
 arch/arm/mach-davinci/aemif.c                      |   86 +++++-
 arch/arm/mach-davinci/board-enbw-cmc.c             |  374 ++++++++++++++++++++
 arch/arm/mach-davinci/cp_intc.c                    |   74 ++++-
 arch/arm/mach-davinci/include/mach/aemif.h         |    1 +
 arch/arm/mach-davinci/include/mach/uncompress.h    |    1 +
 drivers/i2c/busses/i2c-davinci.c                   |   32 ++
 drivers/mtd/nand/davinci_nand.c                    |   80 ++++-
 drivers/net/ethernet/ti/davinci_emac.c             |   87 +++++-
 17 files changed, 1317 insertions(+), 13 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/arm/davinci/aemif.txt
 create mode 100644 Documentation/devicetree/bindings/arm/davinci/i2c.txt
 create mode 100644 Documentation/devicetree/bindings/arm/davinci/intc.txt
 create mode 100644 Documentation/devicetree/bindings/arm/davinci/nand.txt
 create mode 100644 Documentation/devicetree/bindings/net/davinci_emac.txt
 create mode 100644 arch/arm/boot/dts/enbw_cmc.dts
 create mode 100644 arch/arm/configs/enbw_cmc_defconfig
 create mode 100644 arch/arm/mach-davinci/board-enbw-cmc.c

-- 
1.7.7.6

[PATCH v4 4/7] ARM: davinci: net: davinci_emac: add OF support

[Heiko Schocher]

add of support for the davinci_emac driver.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatoly Sivov <mm05@mail.ru>

---
- changes for v2:
  - add comment from Anatoly Sivov
    - fix typo in davinci_emac.txt
  - add comment from Grant Likely:
    - add prefix "ti,davinci-" to davinci specific property names
    - remove version property
    - use compatible name "ti,davinci-dm6460-emac"
    - use devm_kzalloc()
    - use of_match_ptr()
    - document all new properties
    - remove of_address_to_resource() and do not overwrite
      resource table
    - whitespace fixes
    - remove hw_ram_addr as it is not used in current
      board code
- no changes for v3
- changes for v4:
  add comments from Nori Sekhar:
  - move devictree documentation to:
    Documentation/devicetree/bindings/net/davinci_emac.txt
  - fix typo in it
  - rename compatible property to "ti,davinci-dm6467-emac"
  - remove pinmux-handle
  - set version directly in pdata->version
---
 .../devicetree/bindings/net/davinci_emac.txt       |   41 +++++++++
 drivers/net/ethernet/ti/davinci_emac.c             |   87 +++++++++++++++++++-
 2 files changed, 127 insertions(+), 1 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/davinci_emac.txt

diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt
new file mode 100644
index 0000000..48b259e
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/davinci_emac.txt
@@ -0,0 +1,41 @@
+* Texas Instruments Davinci EMAC
+
+This file provides information, what the device node
+for the davinci_emac interface contains.
+
+Required properties:
+- compatible: "ti,davinci-dm6467-emac";
+- reg: Offset and length of the register set for the device
+- ti,davinci-ctrl-reg-offset: offset to control register
+- ti,davinci-ctrl-mod-reg-offset: offset to control module register
+- ti,davinci-ctrl-ram-offset: offset to control module ram
+- ti,davinci-ctrl-ram-size: size of control module ram
+- ti,davinci-rmii-en: use RMII
+- ti,davinci-no-bd-ram: has the emac controller BD RAM
+- phy-handle: Contains a phandle to an Ethernet PHY.
+              if not, davinci_emac driver defaults to 100/FULL
+- interrupts: interrupt mapping for the davinci emac interrupts sources:
+              4 sources: <Receive Threshold Interrupt
+			  Receive Interrupt
+			  Transmit Interrupt
+			  Miscellaneous Interrupt>
+
+Optional properties:
+- local-mac-address : 6 bytes, mac address
+
+Example (enbw_cmc board):
+	eth0: emac@1e20000 {
+		compatible = "ti,davinci-dm6467-emac";
+		reg = <0x220000 0x4000>;
+		ti,davinci-ctrl-reg-offset = <0x3000>;
+		ti,davinci-ctrl-mod-reg-offset = <0x2000>;
+		ti,davinci-ctrl-ram-offset = <0>;
+		ti,davinci-ctrl-ram-size = <0x2000>;
+		local-mac-address = [ 00 00 00 00 00 00 ];
+		interrupts = <33
+				34
+				35
+				36
+				>;
+		interrupt-parent = <&intc>;
+	};
diff --git a/drivers/net/ethernet/ti/davinci_emac.c b/drivers/net/ethernet/ti/davinci_emac.c
index 4da93a5..645618d 100644
--- a/drivers/net/ethernet/ti/davinci_emac.c
+++ b/drivers/net/ethernet/ti/davinci_emac.c
@@ -58,6 +58,12 @@
 #include <linux/io.h>
 #include <linux/uaccess.h>
 #include <linux/davinci_emac.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_net.h>
+
+#include <mach/mux.h>
 
 #include <asm/irq.h>
 #include <asm/page.h>
@@ -339,6 +345,9 @@ struct emac_priv {
 	u32 rx_addr_type;
 	atomic_t cur_tx;
 	const char *phy_id;
+#ifdef CONFIG_OF
+	struct device_node *phy_node;
+#endif
 	struct phy_device *phydev;
 	spinlock_t lock;
 	/*platform specific members*/
@@ -1762,6 +1771,75 @@ static const struct net_device_ops emac_netdev_ops = {
 #endif
 };
 
+#ifdef CONFIG_OF
+static struct emac_platform_data
+	*davinci_emac_of_get_pdata(struct platform_device *pdev,
+	struct emac_priv *priv)
+{
+	struct device_node *np;
+	struct emac_platform_data *pdata = NULL;
+	const u8 *mac_addr;
+	u32 data;
+	int ret;
+
+	pdata = pdev->dev.platform_data;
+	if (!pdata) {
+		pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+		if (!pdata)
+			goto nodata;
+	}
+
+	np = pdev->dev.of_node;
+	if (!np)
+		goto nodata;
+	else
+		pdata->version = EMAC_VERSION_2;
+
+	mac_addr = of_get_mac_address(np);
+	if (mac_addr)
+		memcpy(pdata->mac_addr, mac_addr, ETH_ALEN);
+
+	ret = of_property_read_u32(np, "ti,davinci-ctrl-reg-offset", &data);
+	if (!ret)
+		pdata->ctrl_reg_offset = data;
+
+	ret = of_property_read_u32(np, "ti,davinci-ctrl-mod-reg-offset",
+		&data);
+	if (!ret)
+		pdata->ctrl_mod_reg_offset = data;
+
+	ret = of_property_read_u32(np, "ti,davinci-ctrl-ram-offset", &data);
+	if (!ret)
+		pdata->ctrl_ram_offset = data;
+
+	ret = of_property_read_u32(np, "ti,davinci-ctrl-ram-size", &data);
+	if (!ret)
+		pdata->ctrl_ram_size = data;
+
+	ret = of_property_read_u32(np, "ti,davinci-rmii-en", &data);
+	if (!ret)
+		pdata->rmii_en = data;
+
+	ret = of_property_read_u32(np, "ti,davinci-no-bd-ram", &data);
+	if (!ret)
+		pdata->no_bd_ram = data;
+
+	priv->phy_node = of_parse_phandle(np, "phy-handle", 0);
+	if (!priv->phy_node)
+		pdata->phy_id = "";
+
+	pdev->dev.platform_data = pdata;
+nodata:
+	return  pdata;
+}
+#else
+static struct emac_platform_data
+	*davinci_emac_of_get_pdata(struct platform_device *pdev,
+	struct emac_priv *priv)
+{
+	return  pdev->dev.platform_data;
+}
+#endif
 /**
  * davinci_emac_probe: EMAC device probe
  * @pdev: The DaVinci EMAC device that we are removing
@@ -1804,7 +1882,7 @@ static int __devinit davinci_emac_probe(struct platform_device *pdev)
 
 	spin_lock_init(&priv->lock);
 
-	pdata = pdev->dev.platform_data;
+	pdata = davinci_emac_of_get_pdata(pdev, priv);
 	if (!pdata) {
 		dev_err(&pdev->dev, "no platform data\n");
 		rc = -ENODEV;
@@ -2015,6 +2093,12 @@ static const struct dev_pm_ops davinci_emac_pm_ops = {
 	.resume		= davinci_emac_resume,
 };
 
+static const struct of_device_id davinci_emac_of_match[] = {
+	{.compatible = "ti,davinci-dm6467-emac", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, davinci_emac_of_match);
+
 /**
  * davinci_emac_driver: EMAC platform driver structure
  */
@@ -2023,6 +2107,7 @@ static struct platform_driver davinci_emac_driver = {
 		.name	 = "davinci_emac",
 		.owner	 = THIS_MODULE,
 		.pm	 = &davinci_emac_pm_ops,
+		.of_match_table = of_match_ptr(davinci_emac_of_match),
 	},
 	.probe = davinci_emac_probe,
 	.remove = __devexit_p(davinci_emac_remove),
-- 
1.7.7.6

[PATCH v4 7/7] ARM: davinci: add support for the am1808 based enbw_cmc board

[Heiko Schocher]

- AM1808 based board
- 64 MiB DDR ram
- 2 MiB Nor flash
- 128 MiB NAND flash
- use internal RTC
- I2C support
- hwmon lm75 support
- UBI/UBIFS support
- MMC support
- USB OTG support

Signed-off-by: Heiko Schocher <hs-ynQEQJNshbs@public.gmane.org>
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ@public.gmane.org
Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org
Cc: linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: netdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: David Woodhouse <dwmw2-wEGCiKHe2LqWVfeAwA7xHQ@public.gmane.org>
Cc: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
Cc: Wolfram Sang <w.sang-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
Cc: Sekhar Nori <nsekhar-l0cyMroinI0@public.gmane.org>
Cc: Kevin Hilman <khilman-l0cyMroinI0@public.gmane.org>
Cc: Wolfgang Denk <wd-ynQEQJNshbs@public.gmane.org>
Cc: Scott Wood <scottwood-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Cc: Sylwester Nawrocki <s.nawrocki-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>

---
- post this board support with USB support, even though
  USB is only working with the 10 ms "workaround", posted here:
  http://comments.gmane.org/gmane.linux.usb.general/54505
  I see this issue also on the AM1808 TMDXEXP1808L evalboard.
- MMC and USB are not using OF support yet, ideas how to port
  this are welcome. I need for USB and MMC boards board
  specific callbacks, how to solve this with OF support?

- changes for v2:
  - changes in the nand node due to comments from Scott Wood:
    - add "ti,davinci-" prefix
    - Dashes are preferred to underscores
    - rename "nandflash" to "nand"
    - introduce new "ti,davinci" specific properties for setting
      up ecc_mode, ecc_bits, options and bbt options, instead
      using linux defines
  - changes for i2c due to comments from Sylwester Nawrocki:
    - use "cell-index" instead "id"
    - OF_DEV_AUXDATA in the machine code, instead pre-define
      platform device name
  - add comment from Grant Likely for i2c:
    - removed "id" resp. "cell-index" completely
    - fixed documentation
    - use of_match_ptr()
    - use devm_kzalloc() for allocating plattform data mem
    - fixed a whitespace issue
  - add net comments from Grant Likely:
    - add prefix "ti,davinci-" to davinci specific property names
    - remove version property
    - use compatible name "ti,davinci-dm6460-emac"
  - add comment from Grant Likely:
    - rename compatible node
    - do not use cell-index
    - CONFIG_OF required for this board
    TODO:
    - create a generic board support file, as I got no
      answer to my ping to grant, maybe this could be done
      in a second step?
- changes for v3:
  - add comments from Sergei Shtylyov:
    - rename compatible" prop to "ti,cp_intc"
    - cp_intc_init now used for Interrupt controller init
- changes for v4:
  add comment from Nori Sekhar:
  - rename davinci emac compatible property to "ti,davinci-dm6467-emac"
  - remove "pinmux-handle" property as discussed here:
    http://www.spinics.net/lists/arm-kernel/msg175701.html
    with Nori Sekhar
---
 arch/arm/boot/dts/enbw_cmc.dts                  |  172 +++++++++++
 arch/arm/configs/enbw_cmc_defconfig             |  123 ++++++++
 arch/arm/mach-davinci/Kconfig                   |    9 +
 arch/arm/mach-davinci/Makefile                  |    1 +
 arch/arm/mach-davinci/board-enbw-cmc.c          |  374 +++++++++++++++++++++++
 arch/arm/mach-davinci/include/mach/uncompress.h |    1 +
 6 files changed, 680 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/boot/dts/enbw_cmc.dts
 create mode 100644 arch/arm/configs/enbw_cmc_defconfig
 create mode 100644 arch/arm/mach-davinci/board-enbw-cmc.c

diff --git a/arch/arm/boot/dts/enbw_cmc.dts b/arch/arm/boot/dts/enbw_cmc.dts
new file mode 100644
index 0000000..2d5dea9
--- /dev/null
+++ b/arch/arm/boot/dts/enbw_cmc.dts
@@ -0,0 +1,172 @@
+/*
+ * Device Tree for the EnBW CMC plattform
+ *
+ * Copyright 2011 DENX Software Engineering GmbH
+ * Heiko Schocher <hs-ynQEQJNshbs@public.gmane.org>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+/dts-v1/;
+/include/ "skeleton.dtsi"
+
+/ {
+	model = "EnBW CMC";
+	compatible = "enbw,cmc";
+
+	aliases {
+		ethernet0 = &eth0;
+	};
+
+	arm {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xfffee000 0x00020000>;
+		intc: interrupt-controller@1 {
+			compatible = "ti,cp_intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			ti,intc-size = <101>;
+			reg = <0x0 0x2000>;
+		};
+	};
+	soc@1c00000 {
+		compatible = "ti,da850";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x01c00000 0x400000>;
+
+		serial0: serial@1c42000 {
+			compatible = "ti,da850", "ns16550a";
+			reg = <0x42000 0x100>;
+			clock-frequency = <150000000>;
+			reg-shift = <2>;
+			interrupts = <25>;
+			interrupt-parent = <&intc>;
+		};
+		serial1: serial@1d0c000 {
+			compatible = "ti,da850", "ns16550a";
+			reg = <0x10c000 0x100>;
+			clock-frequency = <150000000>;
+			reg-shift = <2>;
+			interrupts = <53>;
+			interrupt-parent = <&intc>;
+		};
+		serial2: serial@1d0d000 {
+			compatible = "ti,da850", "ns16550a";
+			reg = <0x10d000 0x100>;
+			clock-frequency = <150000000>;
+			reg-shift = <2>;
+			interrupts = <61>;
+			interrupt-parent = <&intc>;
+		};
+
+		eth0: emac@1e20000 {
+			compatible = "ti,davinci-dm6467-emac";
+			reg = <0x220000 0x4000>;
+			ti,davinci-ctrl-reg-offset = <0x3000>;
+			ti,davinci-ctrl-mod-reg-offset = <0x2000>;
+			ti,davinci-ctrl-ram-offset = <0>;
+			ti,davinci-ctrl-ram-size = <0x2000>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <33
+					34
+					35
+					36
+					>;
+			interrupt-parent = <&intc>;
+		};
+
+		i2c@1c22000 {
+			compatible = "ti,davinci-i2c";
+			reg = <0x22000 0x1000>;
+			clock-frequency = <100000>;
+			interrupts = <15>;
+			interrupt-parent = <&intc>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dtt@48 {
+				compatible = "national,lm75";
+				reg = <0x48>;
+			};
+		};
+	};
+	onchipram@8000000 {
+		compatible = "ti,davinci-onchipram";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x80000000 0x20000>;
+	};
+	aemif@60000000 {
+		compatible = "ti,davinci-aemif";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <0x68000000 0x80000>;
+		ranges = <2 0 0x60000000 0x02000000
+			  3 0 0x62000000 0x02000000
+			  4 0 0x64000000 0x02000000
+			  5 0 0x66000000 0x02000000
+			  6 0 0x68000000 0x02000000>;
+		cs2@68000000 {
+			compatible = "ti,davinci-cs";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/* all timings in nanoseconds */
+			cs = <2>;
+			asize = <1>;
+			ta = <0>;
+			rhold = <7>;
+			rstrobe = <42>;
+			rsetup = <14>;
+			whold = <7>;
+			wstrobe = <42>;
+			wsetup = <14>;
+			ew = <0>;
+			ss = <0>;
+		};
+		flash@2,0 {
+			compatible = "cfi-flash";
+			reg = <2 0x0 0x400000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bank-width = <2>;
+			device-width = <2>;
+		};
+		nand_cs: cs3@68000000 {
+			compatible = "ti,davinci-cs";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/* all timings in nanoseconds */
+			cs = <3>;
+			asize = <0>;
+			ta = <0>;
+			rhold = <7>;
+			rstrobe = <42>;
+			rsetup = <7>;
+			whold = <7>;
+			wstrobe = <14>;
+			wsetup = <7>;
+			ew = <0>;
+			ss = <0>;
+		};
+		nand@3,0 {
+			compatible = "ti,davinci-nand";
+			reg = <3 0x0 0x807ff
+				6 0x0 0x8000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ti,davinci-chipselect = <1>;
+			ti,davinci-mask-ale = <0>;
+			ti,davinci-mask-cle = <0>;
+			ti,davinci-mask-chipsel = <0>;
+			ti,davinci-ecc-mode = "hw";
+			ti,davinci-ecc-bits = <4>;
+			ti,davinci-nand-use-bbt;
+			timing-handle = <&nand_cs>;
+		};
+
+	};
+};
diff --git a/arch/arm/configs/enbw_cmc_defconfig b/arch/arm/configs/enbw_cmc_defconfig
new file mode 100644
index 0000000..9d98e7f
--- /dev/null
+++ b/arch/arm/configs/enbw_cmc_defconfig
@@ -0,0 +1,123 @@
+CONFIG_EXPERIMENTAL=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_DAVINCI=y
+CONFIG_ARCH_DAVINCI_DA850=y
+# CONFIG_MACH_DAVINCI_DA850_EVM is not set
+CONFIG_GPIO_PCA953X=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_USE_OF=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_INET_LRO is not set
+CONFIG_IPV6=y
+CONFIG_NETFILTER=y
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_FW_LOADER is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_DAVINCI=y
+CONFIG_MTD_UBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=1
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_NETDEVICES=y
+CONFIG_MII=y
+CONFIG_TI_DAVINCI_EMAC=y
+# CONFIG_WLAN is not set
+CONFIG_INPUT_POLLDEV=y
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_EVBUG=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=3
+CONFIG_SERIAL_8250_RUNTIME_UARTS=3
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_DAVINCI=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_PCF857X=y
+CONFIG_SENSORS_LM75=y
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_CORE=y
+CONFIG_DAVINCI_WATCHDOG=y
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_MUSB_DA8XX=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_UAS=y
+CONFIG_USB_LIBUSUAL=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_FUSB300=y
+CONFIG_USB_ETH=y
+CONFIG_MMC=y
+CONFIG_MMC_DAVINCI=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_OMAP=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
+CONFIG_CRAMFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_DEBUG_FS=y
+CONFIG_TIMER_STATS=y
+CONFIG_DEBUG_RT_MUTEXES=y
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_CCITT=m
+CONFIG_CRC_T10DIF=m
diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig
index 32d837d..4cb0469 100644
--- a/arch/arm/mach-davinci/Kconfig
+++ b/arch/arm/mach-davinci/Kconfig
@@ -202,6 +202,15 @@ config DA850_WL12XX
 	  Say Y if you want to use a wl1271 expansion card connected to the
 	  AM18x EVM.
 
+config MACH_ENBW_CMC
+	bool "EnBW Communication Module Compact"
+	default ARCH_DAVINCI_DA850
+	depends on ARCH_DAVINCI_DA850
+	select OF
+	help
+	  Say Y here to select the EnBW Communication Module Compact
+	  board.
+
 config GPIO_PCA953X
 	default MACH_DAVINCI_DA850_EVM
 
diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile
index 2db78bd..12f3166 100644
--- a/arch/arm/mach-davinci/Makefile
+++ b/arch/arm/mach-davinci/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_MACH_DAVINCI_DA850_EVM)	+= board-da850-evm.o
 obj-$(CONFIG_MACH_TNETV107X)		+= board-tnetv107x-evm.o
 obj-$(CONFIG_MACH_MITYOMAPL138)		+= board-mityomapl138.o
 obj-$(CONFIG_MACH_OMAPL138_HAWKBOARD)	+= board-omapl138-hawk.o
+obj-$(CONFIG_MACH_ENBW_CMC)		+= board-enbw-cmc.o
 
 # Power Management
 obj-$(CONFIG_CPU_FREQ)			+= cpufreq.o
diff --git a/arch/arm/mach-davinci/board-enbw-cmc.c b/arch/arm/mach-davinci/board-enbw-cmc.c
new file mode 100644
index 0000000..fcec14f
--- /dev/null
+++ b/arch/arm/mach-davinci/board-enbw-cmc.c
@@ -0,0 +1,374 @@
+/*
+ * EnBW Communication Module Compact board
+ * Copyright 2011 DENX Software Engineering GmbH
+ * Author: Heiko Schocher <hs-ynQEQJNshbs@public.gmane.org>
+ *
+ * based on:
+ * TI DA850/OMAP-L138 EVM board
+ *
+ * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Derived from: arch/arm/mach-davinci/board-da850-evm.c
+ * Original Copyrights follow:
+ *
+ * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#include <linux/console.h>
+#include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/phy_fixed.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/aemif.h>
+#include <mach/cp_intc.h>
+#include <mach/da8xx.h>
+#include <mach/mux.h>
+#include <mach/nand.h>
+#include <mach/spi.h>
+
+#define ENBW_CMC_MMCSD_CD_PIN          GPIO_TO_PIN(3, 13)
+
+/*
+ * USB1 VBUS is controlled by GPIO7[12], over-current is reported on GPIO7[8].
+ */
+#define DA850_USB_VBUS_PIN	GPIO_TO_PIN(7, 12)
+#define ON_BD_USB_OVC		GPIO_TO_PIN(7, 8)
+
+#if defined(CONFIG_USB_OHCI_HCD)
+static irqreturn_t enbw_cmc_usb_ocic_irq(int irq, void *dev_id);
+static da8xx_ocic_handler_t enbw_cmc_usb_ocic_handler;
+
+static int enbw_cmc_usb_set_power(unsigned port, int on)
+{
+	gpio_set_value(DA850_USB_VBUS_PIN, on);
+	return 0;
+}
+
+static int enbw_cmc_usb_get_power(unsigned port)
+{
+	return gpio_get_value(DA850_USB_VBUS_PIN);
+}
+
+static int enbw_cmc_usb_get_oci(unsigned port)
+{
+	return !gpio_get_value(ON_BD_USB_OVC);
+}
+
+static irqreturn_t enbw_cmc_usb_ocic_irq(int, void *);
+
+static int enbw_cmc_usb_ocic_notify(da8xx_ocic_handler_t handler)
+{
+	int irq         = gpio_to_irq(ON_BD_USB_OVC);
+	int error       = 0;
+
+	if (handler != NULL) {
+		enbw_cmc_usb_ocic_handler = handler;
+
+		error = request_irq(irq, enbw_cmc_usb_ocic_irq,
+					IRQF_DISABLED | IRQF_TRIGGER_RISING |
+					IRQF_TRIGGER_FALLING,
+					"OHCI over-current indicator", NULL);
+		if (error)
+			pr_err("%s: could not request IRQ to watch "
+				"over-current indicator changes\n", __func__);
+	} else {
+		free_irq(irq, NULL);
+	}
+	return error;
+}
+
+static struct da8xx_ohci_root_hub enbw_cmc_usb11_pdata = {
+	.set_power      = enbw_cmc_usb_set_power,
+	.get_power      = enbw_cmc_usb_get_power,
+	.get_oci        = enbw_cmc_usb_get_oci,
+	.ocic_notify    = enbw_cmc_usb_ocic_notify,
+	.potpgt         = (10 + 1) / 2,  /* 10 ms max */
+};
+
+static irqreturn_t enbw_cmc_usb_ocic_irq(int irq, void *dev_id)
+{
+	enbw_cmc_usb_ocic_handler(&enbw_cmc_usb11_pdata, 1);
+	return IRQ_HANDLED;
+}
+#endif
+
+static __init void enbw_cmc_usb_init(void)
+{
+	int ret;
+	u32 cfgchip2;
+
+	/* Set up USB clock/mode in the CFGCHIP2 register. */
+	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	/* USB2.0 PHY reference clock is AUXCLK with 24MHz */
+	cfgchip2 &= ~CFGCHIP2_REFFREQ;
+	cfgchip2 |=  CFGCHIP2_REFFREQ_24MHZ;
+
+	/*
+	 * Select internal reference clock for USB 2.0 PHY
+	 * and use it as a clock source for USB 1.1 PHY
+	 * (this is the default setting anyway).
+	 */
+	cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX;
+	cfgchip2 |=  CFGCHIP2_USB2PHYCLKMUX;
+
+	cfgchip2 &= ~CFGCHIP2_OTGMODE;
+	cfgchip2 |=  CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN;
+
+	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	/*
+	 * SP2525A @ 5V supplies 500mA,
+	 * with the power on to power good time of 10 ms.
+	 */
+	ret = da8xx_register_usb20(500, 10);
+	if (ret)
+		pr_warning("%s: USB 2.0 registration failed: %d\n",
+			   __func__, ret);
+
+#if defined(CONFIG_USB_OHCI_HCD)
+	ret = gpio_request_one(DA850_USB_VBUS_PIN,
+			GPIOF_DIR_OUT, "USB 1.1 VBUS");
+	if (ret < 0) {
+		pr_err("%s: failed to request GPIO for USB 1.1 port "
+			"power control: %d\n", __func__, ret);
+		return;
+	}
+	gpio_direction_input(DA850_USB_VBUS_PIN);
+
+	ret = gpio_request(ON_BD_USB_OVC, "ON_BD_USB_OVC");
+	if (ret) {
+		printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port "
+		       "over-current indicator: %d\n", __func__, ret);
+		gpio_free(DA850_USB_VBUS_PIN);
+		return;
+	}
+	gpio_direction_input(ON_BD_USB_OVC);
+
+	ret = da8xx_register_usb11(&enbw_cmc_usb11_pdata);
+	if (ret) {
+		pr_warning("%s: USB 1.1 registration failed: %d\n",
+			   __func__, ret);
+		gpio_free(ON_BD_USB_OVC);
+		gpio_free(DA850_USB_VBUS_PIN);
+	}
+#endif
+
+	return;
+}
+
+static int enbw_cmc_mmc_get_ro(int index)
+{
+	return 0;
+}
+
+static int enbw_cmc_mmc_get_cd(int index)
+{
+	return gpio_get_value(ENBW_CMC_MMCSD_CD_PIN) ? 1 : 0;
+}
+
+static struct davinci_mmc_config enbw_cmc_mmc_config = {
+	.get_ro		= enbw_cmc_mmc_get_ro,
+	.get_cd		= enbw_cmc_mmc_get_cd,
+	.wires		= 4,
+	.max_freq	= 50000000,
+	.caps		= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
+	.version	= MMC_CTLR_VERSION_2,
+};
+
+static int __init enbw_cmc_config_emac(void)
+{
+	void __iomem *cfg_chip3_base;
+	u32 val;
+	struct davinci_soc_info *soc_info = &davinci_soc_info;
+
+	if (!machine_is_enbw_cmc())
+		return 0;
+
+	cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
+	val = __raw_readl(cfg_chip3_base);
+	val &= ~BIT(8);
+	pr_info("EMAC: MII PHY configured, RMII PHY will not be"
+						" functional\n");
+
+	/* configure the CFGCHIP3 register for MII */
+	__raw_writel(val, cfg_chip3_base);
+
+	/* use complete info from OF */
+	soc_info->emac_pdata = NULL;
+
+	return 0;
+}
+device_initcall(enbw_cmc_config_emac);
+
+static const s16 da850_dma0_rsv_chans[][2] = {
+	/* (offset, number) */
+	{-1, -1}
+};
+
+static const s16 da850_dma0_rsv_slots[][2] = {
+	/* (offset, number) */
+	{-1, -1}
+};
+
+static const s16 da850_dma1_rsv_chans[][2] = {
+	/* (offset, number) */
+	{-1, -1}
+};
+
+static const s16 da850_dma1_rsv_slots[][2] = {
+	/* (offset, number) */
+	{-1, -1}
+};
+
+static struct edma_rsv_info da850_edma_cc0_rsv = {
+	.rsv_chans	= da850_dma0_rsv_chans,
+	.rsv_slots	= da850_dma0_rsv_slots,
+};
+
+static struct edma_rsv_info da850_edma_cc1_rsv = {
+	.rsv_chans	= da850_dma1_rsv_chans,
+	.rsv_slots	= da850_dma1_rsv_slots,
+};
+
+static struct edma_rsv_info *da850_edma_rsv[2] = {
+	&da850_edma_cc0_rsv,
+	&da850_edma_cc1_rsv,
+};
+
+#ifdef CONFIG_CPU_FREQ
+static __init int da850_evm_init_cpufreq(void)
+{
+	switch (system_rev & 0xF) {
+	case 3:
+		da850_max_speed = 456000;
+		break;
+	case 2:
+		da850_max_speed = 408000;
+		break;
+	case 1:
+		da850_max_speed = 372000;
+		break;
+	}
+
+	return da850_register_cpufreq("pll0_sysclk3");
+}
+#else
+static __init int da850_evm_init_cpufreq(void) { return 0; }
+#endif
+
+struct of_dev_auxdata enbw_cmc_auxdata_lookup[] __initdata = {
+	OF_DEV_AUXDATA("ti,davinci-wdt", 0x01c21000, "ti,davinci-wdt", NULL),
+	OF_DEV_AUXDATA("ti,davinci-i2c", 0x01c22000, "i2c_davinci.1", NULL),
+	OF_DEV_AUXDATA("ti,davinci-i2c", 0x01e28000, "i2c_davinci.2", NULL),
+	OF_DEV_AUXDATA("ti,davinci-dm6467-emac", 0x01e20000, "davinci_emac.1",
+			NULL),
+	{}
+};
+
+const struct of_device_id enbw_cmc_bus_match_table[] = {
+	{ .compatible = "simple-bus", },
+	{ .compatible = "ti,da850", },
+	{ .compatible = "ti,davinci-onchipram", },
+	{ .compatible = "ti,davinci-aemif", },
+	{} /* Empty terminated list */
+};
+
+static __init void enbw_cmc_init(void)
+{
+	int ret;
+
+	of_platform_populate(NULL, enbw_cmc_bus_match_table,
+		enbw_cmc_auxdata_lookup, NULL);
+
+	ret = da8xx_register_watchdog();
+	if (ret)
+		pr_warning("enbw_cmc_init: watchdog registration failed: %d\n",
+				ret);
+
+	ret = da850_register_edma(da850_edma_rsv);
+	if (ret)
+		pr_warning("enbw_cmc_init: edma registration failed: %d\n",
+				ret);
+
+	/*
+	 * shut down uart 0 this port is not used on the board
+	 */
+	__raw_writel(0, IO_ADDRESS(DA8XX_UART0_BASE) + 0x30);
+
+	ret = da8xx_register_rtc();
+	if (ret)
+		pr_warning("enbw_cmc_init: rtc setup failed: %d\n", ret);
+
+	ret = da850_evm_init_cpufreq();
+	if (ret)
+		pr_warning("enbw_cmc_init: cpufreq registration failed: %d\n",
+				ret);
+
+	ret = da8xx_register_cpuidle();
+	if (ret)
+		pr_warning("enbw_cmc_init: cpuidle registration failed: %d\n",
+				ret);
+
+	ret = gpio_request(ENBW_CMC_MMCSD_CD_PIN, "MMC CD\n");
+	if (ret)
+		pr_warning("enbw_cmc_init: can not open GPIO %d\n",
+				ENBW_CMC_MMCSD_CD_PIN);
+	gpio_direction_input(ENBW_CMC_MMCSD_CD_PIN);
+
+	ret = da850_register_mmcsd1(&enbw_cmc_mmc_config);
+	if (ret)
+		pr_warning("enbw_cmc_init: mmcsd1 registration failed:"
+				" %d\n", ret);
+
+	enbw_cmc_usb_init();
+}
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+static int __init enbw_cmc_console_init(void)
+{
+	if (!machine_is_enbw_cmc())
+		return 0;
+
+	return add_preferred_console("ttyS", 2, "115200");
+}
+console_initcall(enbw_cmc_console_init);
+#endif
+
+static void __init enbw_cmc_map_io(void)
+{
+	da850_init();
+}
+
+static const char *enbw_cmc_board_compat[] __initconst = {
+	"enbw,cmc",
+	NULL
+};
+
+MACHINE_START(ENBW_CMC, "EnBW CMC")
+	.map_io		= enbw_cmc_map_io,
+	.init_irq	= cp_intc_init,
+	.timer		= &davinci_timer,
+	.init_machine	= enbw_cmc_init,
+	.dt_compat	= enbw_cmc_board_compat,
+	.dma_zone_size	= SZ_128M,
+	.restart	= da8xx_restart,
+MACHINE_END
diff --git a/arch/arm/mach-davinci/include/mach/uncompress.h b/arch/arm/mach-davinci/include/mach/uncompress.h
index da2fb2c..6119543 100644
--- a/arch/arm/mach-davinci/include/mach/uncompress.h
+++ b/arch/arm/mach-davinci/include/mach/uncompress.h
@@ -98,6 +98,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		DEBUG_LL_DA8XX(davinci_da850_evm,	2);
 		DEBUG_LL_DA8XX(mityomapl138,		1);
 		DEBUG_LL_DA8XX(omapl138_hawkboard,	2);
+		DEBUG_LL_DA8XX(enbw_cmc,		2);
 
 		/* TNETV107x boards */
 		DEBUG_LL_TNETV107X(tnetv107x,		1);
-- 
1.7.7.6