[net-next 00/15][pull request] Intel Wired LAN Driver Updates

[net-next 00/15][pull request] Intel Wired LAN Driver Updates

[Jeff Kirsher]

This series contains updates to e1000e only.

The following are changes since commit 1def9238d4aa2146924994aa4b7dc861f03b9362:
  net_sched: more precise pkt_len computation
and are available in the git repository at:
  git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next master

Bruce Allan (15):
  e1000e: SerDes autoneg flow control
  e1000e: Acquire/release semaphore when writing each EEPROM page
  e1000e: Invalid Image CSUM bit changed for I217
  e1000e: helper functions for accessing EMI registers
  e1000e: 82577: workaround for link drop issue
  e1000e: fix enabling of EEE on 82579 and I217
  e1000e: unexpected "Reset adapter" message when cable pulled
  e1000e: add missing bailout on error
  e1000e: resolve checkpatch PREFER_PR_LEVEL warning
  e1000e: cleanup redundant statistics counter
  e1000e: cleanup unusual comment placement
  e1000e: cleanup unnecessary line wrap
  e1000e: cleanup magic number
  e1000e: cleanup code duplication
  e1000e: merge multiple conditional statements into one

 drivers/net/ethernet/intel/e1000e/defines.h |  10 +-
 drivers/net/ethernet/intel/e1000e/e1000.h   |   2 +-
 drivers/net/ethernet/intel/e1000e/ethtool.c |   1 -
 drivers/net/ethernet/intel/e1000e/hw.h      |   4 +
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 213 +++++++++++++++++++++-------
 drivers/net/ethernet/intel/e1000e/mac.c     | 125 ++++++++++++++++
 drivers/net/ethernet/intel/e1000e/netdev.c  |  67 ++++-----
 drivers/net/ethernet/intel/e1000e/nvm.c     |  26 ++--
 drivers/net/ethernet/intel/e1000e/param.c   |   3 +-
 9 files changed, 340 insertions(+), 111 deletions(-)

-- 
1.7.11.7

[net-next 01/15] e1000e: SerDes autoneg flow control

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

Enables flow control to be set in SerDes autoneg mode. This is what is
done for copper, but relies on a different set of register/bit checks
since this is all done within the Mac registers.

Remove inapplicable comment in defines.h

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |   6 +-
 drivers/net/ethernet/intel/e1000e/hw.h      |   4 +
 drivers/net/ethernet/intel/e1000e/mac.c     | 125 ++++++++++++++++++++++++++++
 3 files changed, 132 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 02a12b6..2073532 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -241,9 +241,9 @@
 #define E1000_CTRL_VME      0x40000000  /* IEEE VLAN mode enable */
 #define E1000_CTRL_PHY_RST  0x80000000  /* PHY Reset */
 
-/* Bit definitions for the Management Data IO (MDIO) and Management Data
- * Clock (MDC) pins in the Device Control Register.
- */
+#define E1000_PCS_LCTL_FORCE_FCTRL	0x80
+
+#define E1000_PCS_LSTS_AN_COMPLETE	0x10000
 
 /* Device Status */
 #define E1000_STATUS_FD         0x00000001      /* Full duplex.0=half,1=full */
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index cf21777..06239fe 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -191,6 +191,10 @@ enum e1e_registers {
 	E1000_ICTXQMTC = 0x0411C, /* Irq Cause Tx Queue MinThreshold Count */
 	E1000_ICRXDMTC = 0x04120, /* Irq Cause Rx Desc MinThreshold Count */
 	E1000_ICRXOC   = 0x04124, /* Irq Cause Receiver Overrun Count */
+	E1000_PCS_LCTL = 0x04208, /* PCS Link Control - RW */
+	E1000_PCS_LSTAT = 0x0420C, /* PCS Link Status - RO */
+	E1000_PCS_ANADV = 0x04218, /* AN advertisement - RW */
+	E1000_PCS_LPAB = 0x0421C, /* Link Partner Ability - RW */
 	E1000_RXCSUM   = 0x05000, /* Rx Checksum Control - RW */
 	E1000_RFCTL    = 0x05008, /* Receive Filter Control */
 	E1000_MTA      = 0x05200, /* Multicast Table Array - RW Array */
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 54d9daf..0fa4c06 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -1021,6 +1021,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 {
 	struct e1000_mac_info *mac = &hw->mac;
 	s32 ret_val = 0;
+	u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg;
 	u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
 	u16 speed, duplex;
 
@@ -1185,6 +1186,130 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		}
 	}
 
+	/* Check for the case where we have SerDes media and auto-neg is
+	 * enabled.  In this case, we need to check and see if Auto-Neg
+	 * has completed, and if so, how the PHY and link partner has
+	 * flow control configured.
+	 */
+	if ((hw->phy.media_type == e1000_media_type_internal_serdes) &&
+	    mac->autoneg) {
+		/* Read the PCS_LSTS and check to see if AutoNeg
+		 * has completed.
+		 */
+		pcs_status_reg = er32(PCS_LSTAT);
+
+		if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) {
+			e_dbg("PCS Auto Neg has not completed.\n");
+			return ret_val;
+		}
+
+		/* The AutoNeg process has completed, so we now need to
+		 * read both the Auto Negotiation Advertisement
+		 * Register (PCS_ANADV) and the Auto_Negotiation Base
+		 * Page Ability Register (PCS_LPAB) to determine how
+		 * flow control was negotiated.
+		 */
+		pcs_adv_reg = er32(PCS_ANADV);
+		pcs_lp_ability_reg = er32(PCS_LPAB);
+
+		/* Two bits in the Auto Negotiation Advertisement Register
+		 * (PCS_ANADV) and two bits in the Auto Negotiation Base
+		 * Page Ability Register (PCS_LPAB) determine flow control
+		 * for both the PHY and the link partner.  The following
+		 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+		 * 1999, describes these PAUSE resolution bits and how flow
+		 * control is determined based upon these settings.
+		 * NOTE:  DC = Don't Care
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+		 *-------|---------|-------|---------|--------------------
+		 *   0   |    0    |  DC   |   DC    | e1000_fc_none
+		 *   0   |    1    |   0   |   DC    | e1000_fc_none
+		 *   0   |    1    |   1   |    0    | e1000_fc_none
+		 *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
+		 *   1   |    0    |   0   |   DC    | e1000_fc_none
+		 *   1   |   DC    |   1   |   DC    | e1000_fc_full
+		 *   1   |    1    |   0   |    0    | e1000_fc_none
+		 *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
+		 *
+		 * Are both PAUSE bits set to 1?  If so, this implies
+		 * Symmetric Flow Control is enabled at both ends.  The
+		 * ASM_DIR bits are irrelevant per the spec.
+		 *
+		 * For Symmetric Flow Control:
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+		 *-------|---------|-------|---------|--------------------
+		 *   1   |   DC    |   1   |   DC    | e1000_fc_full
+		 *
+		 */
+		if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+		    (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) {
+			/* Now we need to check if the user selected Rx ONLY
+			 * of pause frames.  In this case, we had to advertise
+			 * FULL flow control because we could not advertise Rx
+			 * ONLY. Hence, we must now check to see if we need to
+			 * turn OFF the TRANSMISSION of PAUSE frames.
+			 */
+			if (hw->fc.requested_mode == e1000_fc_full) {
+				hw->fc.current_mode = e1000_fc_full;
+				e_dbg("Flow Control = FULL.\n");
+			} else {
+				hw->fc.current_mode = e1000_fc_rx_pause;
+				e_dbg("Flow Control = Rx PAUSE frames only.\n");
+			}
+		}
+		/* For receiving PAUSE frames ONLY.
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+		 *-------|---------|-------|---------|--------------------
+		 *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
+		 */
+		else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+			 (pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+			hw->fc.current_mode = e1000_fc_tx_pause;
+			e_dbg("Flow Control = Tx PAUSE frames only.\n");
+		}
+		/* For transmitting PAUSE frames ONLY.
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+		 *-------|---------|-------|---------|--------------------
+		 *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
+		 */
+		else if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+			 !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+			hw->fc.current_mode = e1000_fc_rx_pause;
+			e_dbg("Flow Control = Rx PAUSE frames only.\n");
+		} else {
+			/* Per the IEEE spec, at this point flow control
+			 * should be disabled.
+			 */
+			hw->fc.current_mode = e1000_fc_none;
+			e_dbg("Flow Control = NONE.\n");
+		}
+
+		/* Now we call a subroutine to actually force the MAC
+		 * controller to use the correct flow control settings.
+		 */
+		pcs_ctrl_reg = er32(PCS_LCTL);
+		pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL;
+		ew32(PCS_LCTL, pcs_ctrl_reg);
+
+		ret_val = e1000e_force_mac_fc(hw);
+		if (ret_val) {
+			e_dbg("Error forcing flow control settings\n");
+			return ret_val;
+		}
+	}
+
 	return 0;
 }
 
-- 
1.7.11.7

[net-next 02/15] e1000e: Acquire/release semaphore when writing each EEPROM page

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

When data blocks are written to the EEPROM, the HW/SW/FW semaphore must be
held for the duration.  With large data blocks on 80003es2lan, 82571 and
82572, this can take too long and cause the firmware to take ownership of
the semaphore and consequently ownership of writes to the EEPROM.
Instead, acquire and release the semaphore for each page of the block
written.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/nvm.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/nvm.c b/drivers/net/ethernet/intel/e1000e/nvm.c
index b646880..71938ed 100644
--- a/drivers/net/ethernet/intel/e1000e/nvm.c
+++ b/drivers/net/ethernet/intel/e1000e/nvm.c
@@ -359,7 +359,7 @@ s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 {
 	struct e1000_nvm_info *nvm = &hw->nvm;
-	s32 ret_val;
+	s32 ret_val = -E1000_ERR_NVM;
 	u16 widx = 0;
 
 	/* A check for invalid values:  offset too large, too many words,
@@ -371,16 +371,18 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 		return -E1000_ERR_NVM;
 	}
 
-	ret_val = nvm->ops.acquire(hw);
-	if (ret_val)
-		return ret_val;
-
 	while (widx < words) {
 		u8 write_opcode = NVM_WRITE_OPCODE_SPI;
 
-		ret_val = e1000_ready_nvm_eeprom(hw);
+		ret_val = nvm->ops.acquire(hw);
 		if (ret_val)
-			goto release;
+			return ret_val;
+
+		ret_val = e1000_ready_nvm_eeprom(hw);
+		if (ret_val) {
+			nvm->ops.release(hw);
+			return ret_val;
+		}
 
 		e1000_standby_nvm(hw);
 
@@ -413,12 +415,10 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 				break;
 			}
 		}
+		usleep_range(10000, 20000);
+		nvm->ops.release(hw);
 	}
 
-	usleep_range(10000, 20000);
-release:
-	nvm->ops.release(hw);
-
 	return ret_val;
 }
 
-- 
1.7.11.7

[net-next 03/15] e1000e: Invalid Image CSUM bit changed for I217

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

On I217, the bit that indicates an invalid EEPROM (NVM) image checksum has
changed from previous ICH/PCH LOMs.  When validating the EEPROM checksum,
check the appropriate bit on different devices.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  4 ++++
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 29 +++++++++++++++++++++--------
 2 files changed, 25 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 2073532..7326ea2 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -639,6 +639,10 @@
 /* NVM Word Offsets */
 #define NVM_COMPAT                 0x0003
 #define NVM_ID_LED_SETTINGS        0x0004
+#define NVM_FUTURE_INIT_WORD1      0x0019
+#define NVM_COMPAT_VALID_CSUM      0x0001
+#define NVM_FUTURE_INIT_WORD1_VALID_CSUM	0x0040
+
 #define NVM_INIT_CONTROL2_REG      0x000F
 #define NVM_INIT_CONTROL3_PORT_B   0x0014
 #define NVM_INIT_3GIO_3            0x001A
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 9763365..7d5f6b7 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -2949,19 +2949,32 @@ static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw)
 {
 	s32 ret_val;
 	u16 data;
+	u16 word;
+	u16 valid_csum_mask;
 
-	/* Read 0x19 and check bit 6.  If this bit is 0, the checksum
-	 * needs to be fixed.  This bit is an indication that the NVM
-	 * was prepared by OEM software and did not calculate the
-	 * checksum...a likely scenario.
+	/* Read NVM and check Invalid Image CSUM bit.  If this bit is 0,
+	 * the checksum needs to be fixed.  This bit is an indication that
+	 * the NVM was prepared by OEM software and did not calculate
+	 * the checksum...a likely scenario.
 	 */
-	ret_val = e1000_read_nvm(hw, 0x19, 1, &data);
+	switch (hw->mac.type) {
+	case e1000_pch_lpt:
+		word = NVM_COMPAT;
+		valid_csum_mask = NVM_COMPAT_VALID_CSUM;
+		break;
+	default:
+		word = NVM_FUTURE_INIT_WORD1;
+		valid_csum_mask = NVM_FUTURE_INIT_WORD1_VALID_CSUM;
+		break;
+	}
+
+	ret_val = e1000_read_nvm(hw, word, 1, &data);
 	if (ret_val)
 		return ret_val;
 
-	if (!(data & 0x40)) {
-		data |= 0x40;
-		ret_val = e1000_write_nvm(hw, 0x19, 1, &data);
+	if (!(data & valid_csum_mask)) {
+		data |= valid_csum_mask;
+		ret_val = e1000_write_nvm(hw, word, 1, &data);
 		if (ret_val)
 			return ret_val;
 		ret_val = e1000e_update_nvm_checksum(hw);
-- 
1.7.11.7

[net-next 04/15] e1000e: helper functions for accessing EMI registers

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

The Extended Management Interface (EMI) registers are accessed by first
writing the EMI register offset to the EMI_ADDR regiter and then either
reading or writing the data to/from the EMI_DATA register.  Add helper
functions for performing these steps and convert existing EMI register
accesses accordingly.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 84 ++++++++++++++++++++++-------
 1 file changed, 65 insertions(+), 19 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 7d5f6b7..8004d71 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -153,7 +153,7 @@
 #define I82579_LPI_CTRL_ENABLE_MASK		0x6000
 #define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
 
-/* EMI Registers */
+/* Extended Management Interface (EMI) Registers */
 #define I82579_EMI_ADDR         0x10
 #define I82579_EMI_DATA         0x11
 #define I82579_LPI_UPDATE_TIMER 0x4805	/* in 40ns units + 40 ns base value */
@@ -789,6 +789,58 @@ static s32 e1000_init_mac_params_ich8lan(struct e1000_hw *hw)
 }
 
 /**
+ *  __e1000_access_emi_reg_locked - Read/write EMI register
+ *  @hw: pointer to the HW structure
+ *  @addr: EMI address to program
+ *  @data: pointer to value to read/write from/to the EMI address
+ *  @read: boolean flag to indicate read or write
+ *
+ *  This helper function assumes the SW/FW/HW Semaphore is already acquired.
+ **/
+static s32 __e1000_access_emi_reg_locked(struct e1000_hw *hw, u16 address,
+					 u16 *data, bool read)
+{
+	s32 ret_val = 0;
+
+	ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR, address);
+	if (ret_val)
+		return ret_val;
+
+	if (read)
+		ret_val = e1e_rphy_locked(hw, I82579_EMI_DATA, data);
+	else
+		ret_val = e1e_wphy_locked(hw, I82579_EMI_DATA, *data);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_read_emi_reg_locked - Read Extended Management Interface register
+ *  @hw: pointer to the HW structure
+ *  @addr: EMI address to program
+ *  @data: value to be read from the EMI address
+ *
+ *  Assumes the SW/FW/HW Semaphore is already acquired.
+ **/
+static s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data)
+{
+	return __e1000_access_emi_reg_locked(hw, addr, data, true);
+}
+
+/**
+ *  e1000_write_emi_reg_locked - Write Extended Management Interface register
+ *  @hw: pointer to the HW structure
+ *  @addr: EMI address to program
+ *  @data: value to be written to the EMI address
+ *
+ *  Assumes the SW/FW/HW Semaphore is already acquired.
+ **/
+static s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data)
+{
+	return __e1000_access_emi_reg_locked(hw, addr, &data, false);
+}
+
+/**
  *  e1000_set_eee_pchlan - Enable/disable EEE support
  *  @hw: pointer to the HW structure
  *
@@ -823,11 +875,11 @@ static s32 e1000_set_eee_pchlan(struct e1000_hw *hw)
 		ret_val = hw->phy.ops.acquire(hw);
 		if (ret_val)
 			return ret_val;
-		ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR,
-					  I217_EEE_LP_ABILITY);
+		ret_val = e1000_read_emi_reg_locked(hw,
+						    I217_EEE_LP_ABILITY,
+						    &dev_spec->eee_lp_ability);
 		if (ret_val)
 			goto release;
-		e1e_rphy_locked(hw, I82579_EMI_DATA, &dev_spec->eee_lp_ability);
 
 		/* EEE is not supported in 100Half, so ignore partner's EEE
 		 * in 100 ability if full-duplex is not advertised.
@@ -1987,18 +2039,12 @@ static s32 e1000_lv_phy_workarounds_ich8lan(struct e1000_hw *hw)
 	ret_val = hw->phy.ops.acquire(hw);
 	if (ret_val)
 		return ret_val;
-	ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR, I82579_MSE_THRESHOLD);
-	if (ret_val)
-		goto release;
 	/* set MSE higher to enable link to stay up when noise is high */
-	ret_val = e1e_wphy_locked(hw, I82579_EMI_DATA, 0x0034);
-	if (ret_val)
-		goto release;
-	ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR, I82579_MSE_LINK_DOWN);
+	ret_val = e1000_write_emi_reg_locked(hw, I82579_MSE_THRESHOLD, 0x0034);
 	if (ret_val)
 		goto release;
 	/* drop link after 5 times MSE threshold was reached */
-	ret_val = e1e_wphy_locked(hw, I82579_EMI_DATA, 0x0005);
+	ret_val = e1000_write_emi_reg_locked(hw, I82579_MSE_LINK_DOWN, 0x0005);
 release:
 	hw->phy.ops.release(hw);
 
@@ -2172,10 +2218,9 @@ static s32 e1000_post_phy_reset_ich8lan(struct e1000_hw *hw)
 		ret_val = hw->phy.ops.acquire(hw);
 		if (ret_val)
 			return ret_val;
-		ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR,
-					  I82579_LPI_UPDATE_TIMER);
-		if (!ret_val)
-			ret_val = e1e_wphy_locked(hw, I82579_EMI_DATA, 0x1387);
+		ret_val = e1000_write_emi_reg_locked(hw,
+						     I82579_LPI_UPDATE_TIMER,
+						     0x1387);
 		hw->phy.ops.release(hw);
 	}
 
@@ -4013,11 +4058,12 @@ void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw)
 		if (!dev_spec->eee_disable) {
 			u16 eee_advert;
 
-			ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR,
-						  I217_EEE_ADVERTISEMENT);
+			ret_val =
+			    e1000_read_emi_reg_locked(hw,
+						      I217_EEE_ADVERTISEMENT,
+						      &eee_advert);
 			if (ret_val)
 				goto release;
-			e1e_rphy_locked(hw, I82579_EMI_DATA, &eee_advert);
 
 			/* Disable LPLU if both link partners support 100BaseT
 			 * EEE and 100Full is advertised on both ends of the
-- 
1.7.11.7

[net-next 05/15] e1000e: 82577: workaround for link drop issue

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

When connected to certain switches, the 82577 PHY might drop link
unexpectedly.  Work around the issue by setting the Mean Square Error
higher than the hardware default.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 8004d71..a7d6c87 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -157,7 +157,8 @@
 #define I82579_EMI_ADDR         0x10
 #define I82579_EMI_DATA         0x11
 #define I82579_LPI_UPDATE_TIMER 0x4805	/* in 40ns units + 40 ns base value */
-#define I82579_MSE_THRESHOLD    0x084F	/* Mean Square Error Threshold */
+#define I82579_MSE_THRESHOLD    0x084F	/* 82579 Mean Square Error Threshold */
+#define I82577_MSE_THRESHOLD    0x0887	/* 82577 Mean Square Error Threshold */
 #define I82579_MSE_LINK_DOWN    0x2411	/* MSE count before dropping link */
 #define I217_EEE_ADVERTISEMENT  0x8001	/* IEEE MMD Register 7.60 */
 #define I217_EEE_LP_ABILITY     0x8002	/* IEEE MMD Register 7.61 */
@@ -1809,6 +1810,11 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
 	if (ret_val)
 		goto release;
 	ret_val = e1e_wphy_locked(hw, BM_PORT_GEN_CFG, phy_data & 0x00FF);
+	if (ret_val)
+		goto release;
+
+	/* set MSE higher to enable link to stay up when noise is high */
+	ret_val = e1000_write_emi_reg_locked(hw, I82577_MSE_THRESHOLD, 0x0034);
 release:
 	hw->phy.ops.release(hw);
 
-- 
1.7.11.7

[net-next 06/15] e1000e: fix enabling of EEE on 82579 and I217

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

Energy Efficient Ethernet on 82579 and I217 should only be enabled if not
disabled by the user, if the link is full duplex and the link partner has
similar EEE capabilities (stored in different EMI registers on the two
different parts).

After enabling EEE, read the IEEE MMD register 3.1 (which is also stored in
different EMI registers on the two different parts) to clear the count of
received Tx/Rx LPI indications.

Also, rename I217_EEE_100_SUPPORTED to I82579_EEE_100_SUPPORTED to indicate
the bit is valid starting with I82579 (released before I217).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 94 ++++++++++++++++++++---------
 1 file changed, 65 insertions(+), 29 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index a7d6c87..15d9314 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -150,6 +150,8 @@
 
 /* PHY Low Power Idle Control */
 #define I82579_LPI_CTRL				PHY_REG(772, 20)
+#define I82579_LPI_CTRL_100_ENABLE		0x2000
+#define I82579_LPI_CTRL_1000_ENABLE		0x4000
 #define I82579_LPI_CTRL_ENABLE_MASK		0x6000
 #define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
 
@@ -160,9 +162,13 @@
 #define I82579_MSE_THRESHOLD    0x084F	/* 82579 Mean Square Error Threshold */
 #define I82577_MSE_THRESHOLD    0x0887	/* 82577 Mean Square Error Threshold */
 #define I82579_MSE_LINK_DOWN    0x2411	/* MSE count before dropping link */
+#define I82579_EEE_PCS_STATUS	0x182D	/* IEEE MMD Register 3.1 >> 8 */
+#define I82579_EEE_LP_ABILITY	0x040F	/* IEEE MMD Register 7.61 */
+#define I82579_EEE_100_SUPPORTED	(1 << 1) /* 100BaseTx EEE supported */
+#define I82579_EEE_1000_SUPPORTED	(1 << 2) /* 1000BaseTx EEE supported */
+#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
 #define I217_EEE_ADVERTISEMENT  0x8001	/* IEEE MMD Register 7.60 */
 #define I217_EEE_LP_ABILITY     0x8002	/* IEEE MMD Register 7.61 */
-#define I217_EEE_100_SUPPORTED  (1 << 1)	/* 100BaseTx EEE supported */
 
 /* Intel Rapid Start Technology Support */
 #define I217_PROXY_CTRL                 BM_PHY_REG(BM_WUC_PAGE, 70)
@@ -845,54 +851,84 @@ static s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data)
  *  e1000_set_eee_pchlan - Enable/disable EEE support
  *  @hw: pointer to the HW structure
  *
- *  Enable/disable EEE based on setting in dev_spec structure.  The bits in
- *  the LPI Control register will remain set only if/when link is up.
+ *  Enable/disable EEE based on setting in dev_spec structure, the duplex of
+ *  the link and the EEE capabilities of the link partner.  The LPI Control
+ *  register bits will remain set only if/when link is up.
  **/
 static s32 e1000_set_eee_pchlan(struct e1000_hw *hw)
 {
 	struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
-	s32 ret_val = 0;
-	u16 phy_reg;
+	s32 ret_val;
+	u16 lpi_ctrl;
 
 	if ((hw->phy.type != e1000_phy_82579) &&
 	    (hw->phy.type != e1000_phy_i217))
 		return 0;
 
-	ret_val = e1e_rphy(hw, I82579_LPI_CTRL, &phy_reg);
+	ret_val = hw->phy.ops.acquire(hw);
 	if (ret_val)
 		return ret_val;
 
-	if (dev_spec->eee_disable)
-		phy_reg &= ~I82579_LPI_CTRL_ENABLE_MASK;
-	else
-		phy_reg |= I82579_LPI_CTRL_ENABLE_MASK;
-
-	ret_val = e1e_wphy(hw, I82579_LPI_CTRL, phy_reg);
+	ret_val = e1e_rphy_locked(hw, I82579_LPI_CTRL, &lpi_ctrl);
 	if (ret_val)
-		return ret_val;
+		goto release;
+
+	/* Clear bits that enable EEE in various speeds */
+	lpi_ctrl &= ~I82579_LPI_CTRL_ENABLE_MASK;
+
+	/* Enable EEE if not disabled by user */
+	if (!dev_spec->eee_disable) {
+		u16 lpa, pcs_status, data;
 
-	if ((hw->phy.type == e1000_phy_i217) && !dev_spec->eee_disable) {
 		/* Save off link partner's EEE ability */
-		ret_val = hw->phy.ops.acquire(hw);
-		if (ret_val)
-			return ret_val;
-		ret_val = e1000_read_emi_reg_locked(hw,
-						    I217_EEE_LP_ABILITY,
+		switch (hw->phy.type) {
+		case e1000_phy_82579:
+			lpa = I82579_EEE_LP_ABILITY;
+			pcs_status = I82579_EEE_PCS_STATUS;
+			break;
+		case e1000_phy_i217:
+			lpa = I217_EEE_LP_ABILITY;
+			pcs_status = I217_EEE_PCS_STATUS;
+			break;
+		default:
+			ret_val = -E1000_ERR_PHY;
+			goto release;
+		}
+		ret_val = e1000_read_emi_reg_locked(hw, lpa,
 						    &dev_spec->eee_lp_ability);
 		if (ret_val)
 			goto release;
 
-		/* EEE is not supported in 100Half, so ignore partner's EEE
-		 * in 100 ability if full-duplex is not advertised.
+		/* Enable EEE only for speeds in which the link partner is
+		 * EEE capable.
 		 */
-		e1e_rphy_locked(hw, PHY_LP_ABILITY, &phy_reg);
-		if (!(phy_reg & NWAY_LPAR_100TX_FD_CAPS))
-			dev_spec->eee_lp_ability &= ~I217_EEE_100_SUPPORTED;
-release:
-		hw->phy.ops.release(hw);
+		if (dev_spec->eee_lp_ability & I82579_EEE_1000_SUPPORTED)
+			lpi_ctrl |= I82579_LPI_CTRL_1000_ENABLE;
+
+		if (dev_spec->eee_lp_ability & I82579_EEE_100_SUPPORTED) {
+			e1e_rphy_locked(hw, PHY_LP_ABILITY, &data);
+			if (data & NWAY_LPAR_100TX_FD_CAPS)
+				lpi_ctrl |= I82579_LPI_CTRL_100_ENABLE;
+			else
+				/* EEE is not supported in 100Half, so ignore
+				 * partner's EEE in 100 ability if full-duplex
+				 * is not advertised.
+				 */
+				dev_spec->eee_lp_ability &=
+				    ~I82579_EEE_100_SUPPORTED;
+		}
+
+		/* R/Clr IEEE MMD 3.1 bits 11:10 - Tx/Rx LPI Received */
+		ret_val = e1000_read_emi_reg_locked(hw, pcs_status, &data);
+		if (ret_val)
+			goto release;
 	}
 
-	return 0;
+	ret_val = e1e_wphy_locked(hw, I82579_LPI_CTRL, lpi_ctrl);
+release:
+	hw->phy.ops.release(hw);
+
+	return ret_val;
 }
 
 /**
@@ -4075,9 +4111,9 @@ void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw)
 			 * EEE and 100Full is advertised on both ends of the
 			 * link.
 			 */
-			if ((eee_advert & I217_EEE_100_SUPPORTED) &&
+			if ((eee_advert & I82579_EEE_100_SUPPORTED) &&
 			    (dev_spec->eee_lp_ability &
-			     I217_EEE_100_SUPPORTED) &&
+			     I82579_EEE_100_SUPPORTED) &&
 			    (hw->phy.autoneg_advertised & ADVERTISE_100_FULL))
 				phy_ctrl &= ~(E1000_PHY_CTRL_D0A_LPLU |
 					      E1000_PHY_CTRL_NOND0A_LPLU);
-- 
1.7.11.7

[net-next 07/15] e1000e: unexpected "Reset adapter" message when cable pulled

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

When there is heavy traffic and the cable is pulled, the driver must reset
the adapter to flush the Tx queue in hardware.  This causes the reset path
to be scheduled and logs the message "Reset adapter" which could be mis-
interpreted as an error by the user.  Change how the reset path is invoked
for this scenario by using the same method done in an existing work-around
for 80003es2lan (i.e. set a flag and if the flag is set in the reset code
do not log the "Reset adapter" message since the reset is expected).

Re-name the FLAG_RX_RESTART_NOW to FLAG_RESTART_NOW since it is used for
resets in both the Rx and Tx specific code.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h  |  2 +-
 drivers/net/ethernet/intel/e1000e/netdev.c | 39 +++++++++++++++---------------
 2 files changed, 21 insertions(+), 20 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 6782a2e..3f8bbc3 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -447,7 +447,7 @@ struct e1000_info {
 #define FLAG_MSI_ENABLED                  (1 << 27)
 /* reserved (1 << 28) */
 #define FLAG_TSO_FORCE                    (1 << 29)
-#define FLAG_RX_RESTART_NOW               (1 << 30)
+#define FLAG_RESTART_NOW                  (1 << 30)
 #define FLAG_MSI_TEST_FAILED              (1 << 31)
 
 #define FLAG2_CRC_STRIPPING               (1 << 0)
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 337644d..7ad8ef6 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1671,7 +1671,7 @@ static irqreturn_t e1000_intr_msi(int irq, void *data)
 			/* disable receives */
 			u32 rctl = er32(RCTL);
 			ew32(RCTL, rctl & ~E1000_RCTL_EN);
-			adapter->flags |= FLAG_RX_RESTART_NOW;
+			adapter->flags |= FLAG_RESTART_NOW;
 		}
 		/* guard against interrupt when we're going down */
 		if (!test_bit(__E1000_DOWN, &adapter->state))
@@ -1734,7 +1734,7 @@ static irqreturn_t e1000_intr(int irq, void *data)
 			/* disable receives */
 			rctl = er32(RCTL);
 			ew32(RCTL, rctl & ~E1000_RCTL_EN);
-			adapter->flags |= FLAG_RX_RESTART_NOW;
+			adapter->flags |= FLAG_RESTART_NOW;
 		}
 		/* guard against interrupt when we're going down */
 		if (!test_bit(__E1000_DOWN, &adapter->state))
@@ -3013,7 +3013,7 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 
 	ew32(RCTL, rctl);
 	/* just started the receive unit, no need to restart */
-	adapter->flags &= ~FLAG_RX_RESTART_NOW;
+	adapter->flags &= ~FLAG_RESTART_NOW;
 }
 
 /**
@@ -4355,11 +4355,11 @@ static void e1000e_enable_receives(struct e1000_adapter *adapter)
 {
 	/* make sure the receive unit is started */
 	if ((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
-	    (adapter->flags & FLAG_RX_RESTART_NOW)) {
+	    (adapter->flags & FLAG_RESTART_NOW)) {
 		struct e1000_hw *hw = &adapter->hw;
 		u32 rctl = er32(RCTL);
 		ew32(RCTL, rctl | E1000_RCTL_EN);
-		adapter->flags &= ~FLAG_RX_RESTART_NOW;
+		adapter->flags &= ~FLAG_RESTART_NOW;
 	}
 }
 
@@ -4528,8 +4528,16 @@ static void e1000_watchdog_task(struct work_struct *work)
 				mod_timer(&adapter->phy_info_timer,
 					  round_jiffies(jiffies + 2 * HZ));
 
-			if (adapter->flags & FLAG_RX_NEEDS_RESTART)
-				schedule_work(&adapter->reset_task);
+			/* The link is lost so the controller stops DMA.
+			 * If there is queued Tx work that cannot be done
+			 * or if on an 8000ES2LAN which requires a Rx packet
+			 * buffer work-around on link down event, reset the
+			 * controller to flush the Tx/Rx packet buffers.
+			 * (Do the reset outside of interrupt context).
+			 */
+			if ((adapter->flags & FLAG_RX_NEEDS_RESTART) ||
+			    (e1000_desc_unused(tx_ring) + 1 < tx_ring->count))
+				adapter->flags |= FLAG_RESTART_NOW;
 			else
 				pm_schedule_suspend(netdev->dev.parent,
 							LINK_TIMEOUT);
@@ -4551,20 +4559,14 @@ link_up:
 	adapter->gotc_old = adapter->stats.gotc;
 	spin_unlock(&adapter->stats64_lock);
 
-	e1000e_update_adaptive(&adapter->hw);
-
-	if (!netif_carrier_ok(netdev) &&
-	    (e1000_desc_unused(tx_ring) + 1 < tx_ring->count)) {
-		/* We've lost link, so the controller stops DMA,
-		 * but we've got queued Tx work that's never going
-		 * to get done, so reset controller to flush Tx.
-		 * (Do the reset outside of interrupt context).
-		 */
+	if (adapter->flags & FLAG_RESTART_NOW) {
 		schedule_work(&adapter->reset_task);
 		/* return immediately since reset is imminent */
 		return;
 	}
 
+	e1000e_update_adaptive(&adapter->hw);
+
 	/* Simple mode for Interrupt Throttle Rate (ITR) */
 	if (adapter->itr_setting == 4) {
 		/* Symmetric Tx/Rx gets a reduced ITR=2000;
@@ -5134,10 +5136,9 @@ static void e1000_reset_task(struct work_struct *work)
 	if (test_bit(__E1000_DOWN, &adapter->state))
 		return;
 
-	if (!((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
-	      (adapter->flags & FLAG_RX_RESTART_NOW))) {
+	if (!(adapter->flags & FLAG_RESTART_NOW)) {
 		e1000e_dump(adapter);
-		e_err("Reset adapter\n");
+		e_err("Reset adapter unexpectedly\n");
 	}
 	e1000e_reinit_locked(adapter);
 }
-- 
1.7.11.7

[net-next 08/15] e1000e: add missing bailout on error

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

...discovered during code inspection.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 15d9314..051dfda 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -2077,6 +2077,8 @@ static s32 e1000_lv_phy_workarounds_ich8lan(struct e1000_hw *hw)
 
 	/* Set MDIO slow mode before any other MDIO access */
 	ret_val = e1000_set_mdio_slow_mode_hv(hw);
+	if (ret_val)
+		return ret_val;
 
 	ret_val = hw->phy.ops.acquire(hw);
 	if (ret_val)
-- 
1.7.11.7

[net-next 09/15] e1000e: resolve checkpatch PREFER_PR_LEVEL warning

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(...  to printk(KERN_INFO ...

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 7ad8ef6..e922bba 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -4300,9 +4300,8 @@ static void e1000_print_link_info(struct e1000_adapter *adapter)
 	u32 ctrl = er32(CTRL);
 
 	/* Link status message must follow this format for user tools */
-	printk(KERN_INFO "e1000e: %s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
-		adapter->netdev->name,
-		adapter->link_speed,
+	pr_info("e1000e: %s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
+		adapter->netdev->name, adapter->link_speed,
 		adapter->link_duplex == FULL_DUPLEX ? "Full" : "Half",
 		(ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE) ? "Rx/Tx" :
 		(ctrl & E1000_CTRL_RFCE) ? "Rx" :
@@ -4521,8 +4520,8 @@ static void e1000_watchdog_task(struct work_struct *work)
 			adapter->link_speed = 0;
 			adapter->link_duplex = 0;
 			/* Link status message must follow this format */
-			printk(KERN_INFO "e1000e: %s NIC Link is Down\n",
-			       adapter->netdev->name);
+			pr_info("e1000e: %s NIC Link is Down\n",
+				adapter->netdev->name);
 			netif_carrier_off(netdev);
 			if (!test_bit(__E1000_DOWN, &adapter->state))
 				mod_timer(&adapter->phy_info_timer,
-- 
1.7.11.7

[net-next 10/15] e1000e: cleanup redundant statistics counter

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

rx_long_byte_count can be removed since it is duplicated in rx_bytes

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ethtool.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index f95bc6e..2225603 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -98,7 +98,6 @@ static const struct e1000_stats e1000_gstrings_stats[] = {
 	E1000_STAT("rx_flow_control_xoff", stats.xoffrxc),
 	E1000_STAT("tx_flow_control_xon", stats.xontxc),
 	E1000_STAT("tx_flow_control_xoff", stats.xofftxc),
-	E1000_STAT("rx_long_byte_count", stats.gorc),
 	E1000_STAT("rx_csum_offload_good", hw_csum_good),
 	E1000_STAT("rx_csum_offload_errors", hw_csum_err),
 	E1000_STAT("rx_header_split", rx_hdr_split),
-- 
1.7.11.7

[net-next 11/15] e1000e: cleanup unusual comment placement

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index e922bba..94312a4 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -765,7 +765,7 @@ static void e1000_alloc_jumbo_rx_buffers(struct e1000_ring *rx_ring,
 	struct e1000_buffer *buffer_info;
 	struct sk_buff *skb;
 	unsigned int i;
-	unsigned int bufsz = 256 - 16 /* for skb_reserve */;
+	unsigned int bufsz = 256 - 16;	/* for skb_reserve */
 
 	i = rx_ring->next_to_use;
 	buffer_info = &rx_ring->buffer_info[i];
-- 
1.7.11.7

[net-next 12/15] e1000e: cleanup unnecessary line wrap

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/param.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/param.c b/drivers/net/ethernet/intel/e1000e/param.c
index 89d536d..b29a8a5 100644
--- a/drivers/net/ethernet/intel/e1000e/param.c
+++ b/drivers/net/ethernet/intel/e1000e/param.c
@@ -447,8 +447,7 @@ void e1000e_check_options(struct e1000_adapter *adapter)
 		if (num_SmartPowerDownEnable > bd) {
 			unsigned int spd = SmartPowerDownEnable[bd];
 			e1000_validate_option(&spd, &opt, adapter);
-			if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN)
-			    && spd)
+			if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN) && spd)
 				adapter->flags |= FLAG_SMART_POWER_DOWN;
 		}
 	}
-- 
1.7.11.7

[net-next 13/15] e1000e: cleanup magic number

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/nvm.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/nvm.c b/drivers/net/ethernet/intel/e1000e/nvm.c
index 71938ed..1e7882c 100644
--- a/drivers/net/ethernet/intel/e1000e/nvm.c
+++ b/drivers/net/ethernet/intel/e1000e/nvm.c
@@ -464,8 +464,8 @@ s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 	if (nvm_data != NVM_PBA_PTR_GUARD) {
 		e_dbg("NVM PBA number is not stored as string\n");
 
-		/* we will need 11 characters to store the PBA */
-		if (pba_num_size < 11) {
+		/* make sure callers buffer is big enough to store the PBA */
+		if (pba_num_size < E1000_PBANUM_LENGTH) {
 			e_dbg("PBA string buffer too small\n");
 			return E1000_ERR_NO_SPACE;
 		}
-- 
1.7.11.7

[net-next 14/15] e1000e: cleanup code duplication

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

The removed code block is duplicated in e1000e_write_itr() so use that
instead.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 6 +-----
 1 file changed, 1 insertion(+), 5 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 94312a4..f51b353 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -2405,7 +2405,6 @@ static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
 
 static void e1000_set_itr(struct e1000_adapter *adapter)
 {
-	struct e1000_hw *hw = &adapter->hw;
 	u16 current_itr;
 	u32 new_itr = adapter->itr;
 
@@ -2468,10 +2467,7 @@ set_itr_now:
 		if (adapter->msix_entries)
 			adapter->rx_ring->set_itr = 1;
 		else
-			if (new_itr)
-				ew32(ITR, 1000000000 / (new_itr * 256));
-			else
-				ew32(ITR, 0);
+			e1000e_write_itr(adapter, new_itr);
 	}
 }
 
-- 
1.7.11.7

[net-next 15/15] e1000e: merge multiple conditional statements into one

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

Cleanup a set of conditional tests.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 11 +++++------
 1 file changed, 5 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index f51b353..f76b164 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -4915,12 +4915,11 @@ static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter,
 	struct e1000_hw *hw =  &adapter->hw;
 	u16 length, offset;
 
-	if (vlan_tx_tag_present(skb)) {
-		if (!((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) &&
-		    (adapter->hw.mng_cookie.status &
-			E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
-			return 0;
-	}
+	if (vlan_tx_tag_present(skb) &&
+	    !((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) &&
+	      (adapter->hw.mng_cookie.status &
+	       E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
+		return 0;
 
 	if (skb->len <= MINIMUM_DHCP_PACKET_SIZE)
 		return 0;
-- 
1.7.11.7

RE: [net-next 03/15] e1000e: Invalid Image CSUM bit changed for I217

[David Laight]

> +	/* Read NVM and check Invalid Image CSUM bit.  If this bit is 0,
> +	 * the checksum needs to be fixed.  This bit is an indication that
> +	 * the NVM was prepared by OEM software and did not calculate
> +	 * the checksum...a likely scenario.

Shouldn't the first line read:
	/* Read NVM and check Valid Image CSUM bit.

	David

RE: [net-next 04/15] e1000e: helper functions for accessing EMI registers

[David Laight]

> From: Bruce Allan <bruce.w.allan@intel.com>
> 
> The Extended Management Interface (EMI) registers are accessed by first
> writing the EMI register offset to the EMI_ADDR regiter and then either
> reading or writing the data to/from the EMI_DATA register.  Add helper
> functions for performing these steps and convert existing EMI register
> accesses accordingly.
> 
> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> ---
>  drivers/net/ethernet/intel/e1000e/ich8lan.c | 84 ++++++++++++++++++++++-------
>  1 file changed, 65 insertions(+), 19 deletions(-)
> 
> diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
> index 7d5f6b7..8004d71 100644
> --- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
> +++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
> @@ -153,7 +153,7 @@
>  #define I82579_LPI_CTRL_ENABLE_MASK		0x6000
>  #define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
> 
> -/* EMI Registers */
> +/* Extended Management Interface (EMI) Registers */
>  #define I82579_EMI_ADDR         0x10
>  #define I82579_EMI_DATA         0x11
>  #define I82579_LPI_UPDATE_TIMER 0x4805	/* in 40ns units + 40 ns base value */
> @@ -789,6 +789,58 @@ static s32 e1000_init_mac_params_ich8lan(struct e1000_hw *hw)
>  }
> 
>  /**
> + *  __e1000_access_emi_reg_locked - Read/write EMI register
> + *  @hw: pointer to the HW structure
> + *  @addr: EMI address to program
> + *  @data: pointer to value to read/write from/to the EMI address
> + *  @read: boolean flag to indicate read or write
> + *
> + *  This helper function assumes the SW/FW/HW Semaphore is already acquired.
> + **/
> +static s32 __e1000_access_emi_reg_locked(struct e1000_hw *hw, u16 address,
> +					 u16 *data, bool read)
> +{
> +	s32 ret_val = 0;
> +
> +	ret_val = e1e_wphy_locked(hw, I82579_EMI_ADDR, address);
> +	if (ret_val)
> +		return ret_val;
> +
> +	if (read)
> +		ret_val = e1e_rphy_locked(hw, I82579_EMI_DATA, data);
> +	else
> +		ret_val = e1e_wphy_locked(hw, I82579_EMI_DATA, *data);
> +
> +	return ret_val;
> +}
> +
> +/**
> + *  e1000_read_emi_reg_locked - Read Extended Management Interface register
> + *  @hw: pointer to the HW structure
> + *  @addr: EMI address to program
> + *  @data: value to be read from the EMI address
> + *
> + *  Assumes the SW/FW/HW Semaphore is already acquired.
> + **/
> +static s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data)
> +{
> +	return __e1000_access_emi_reg_locked(hw, addr, data, true);
> +}
> +
> +/**
> + *  e1000_write_emi_reg_locked - Write Extended Management Interface register
> + *  @hw: pointer to the HW structure
> + *  @addr: EMI address to program
> + *  @data: value to be written to the EMI address
> + *
> + *  Assumes the SW/FW/HW Semaphore is already acquired.
> + **/
> +static s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data)
> +{
> +	return __e1000_access_emi_reg_locked(hw, addr, &data, false);
> +}
> +
> +/**

I'm not sure it is worth having all three routines.
Personally I'd inline the first into the latter two.

	David

Re: [net-next 09/15] e1000e: resolve checkpatch PREFER_PR_LEVEL warning

[Joe Perches]

On Fri, 2013-01-11 at 02:23 -0800, Jeff Kirsher wrote:
> WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
> then pr_info(...  to printk(KERN_INFO ...
[]
> diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
[]
> @@ -4300,9 +4300,8 @@ static void e1000_print_link_info(struct e1000_adapter *adapter)
>  	u32 ctrl = er32(CTRL);
>  
>  	/* Link status message must follow this format for user tools */
> -	printk(KERN_INFO "e1000e: %s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
> -		adapter->netdev->name,
> -		adapter->link_speed,
> +	pr_info("e1000e: %s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
> +		adapter->netdev->name, adapter->link_speed,

Don't these changes break a user-space tool?

If not, please remove the comment above the pr_info()s
and remove the unnecessary e1000e: prefixes.

> @@ -4521,8 +4520,8 @@ static void e1000_watchdog_task(struct work_struct *work)
[]
>  			/* Link status message must follow this format */
> -			printk(KERN_INFO "e1000e: %s NIC Link is Down\n",
> -			       adapter->netdev->name);
> +			pr_info("e1000e: %s NIC Link is Down\n",
> +				adapter->netdev->name);

RE: [net-next 09/15] e1000e: resolve checkpatch PREFER_PR_LEVEL warning

[Allan, Bruce W]

> -----Original Message-----
> From: Joe Perches [mailto:joe@perches.com]
> Sent: Friday, January 11, 2013 9:04 AM
> To: Kirsher, Jeffrey T
> Cc: davem@davemloft.net; Allan, Bruce W; netdev@vger.kernel.org;
> gospo@redhat.com; sassmann@redhat.com
> Subject: Re: [net-next 09/15] e1000e: resolve checkpatch PREFER_PR_LEVEL
> warning
> 
> On Fri, 2013-01-11 at 02:23 -0800, Jeff Kirsher wrote:
> > WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
> > then pr_info(...  to printk(KERN_INFO ...
> []
> > diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c
> b/drivers/net/ethernet/intel/e1000e/netdev.c
> []
> > @@ -4300,9 +4300,8 @@ static void e1000_print_link_info(struct
> e1000_adapter *adapter)
> >  	u32 ctrl = er32(CTRL);
> >
> >  	/* Link status message must follow this format for user tools */
> > -	printk(KERN_INFO "e1000e: %s NIC Link is Up %d Mbps %s Duplex,
> Flow Control: %s\n",
> > -		adapter->netdev->name,
> > -		adapter->link_speed,
> > +	pr_info("e1000e: %s NIC Link is Up %d Mbps %s Duplex, Flow
> Control: %s\n",
> > +		adapter->netdev->name, adapter->link_speed,
> 
> Don't these changes break a user-space tool?
> 
> If not, please remove the comment above the pr_info()s
> and remove the unnecessary e1000e: prefixes.
> 
> > @@ -4521,8 +4520,8 @@ static void e1000_watchdog_task(struct
> work_struct *work)
> []
> >  			/* Link status message must follow this format */
> > -			printk(KERN_INFO "e1000e: %s NIC Link is Down\n",
> > -			       adapter->netdev->name);
> > +			pr_info("e1000e: %s NIC Link is Down\n",
> > +				adapter->netdev->name);
> 

Hmm, I'm not sure how that got past our testing even after I asked to check for
redundant instances of "e1000e".  This patch can be dropped and I will submit an
updated one but it will still have the "must follow this format for user tools" comment
since the user tools key off of "e1000e: <iface> NIC Link is ..." text.

Thanks,
Bruce.

[net-next 02/15] e1000e: Acquire/release semaphore when writing each EEPROM page

[Jeff Kirsher]

From: Bruce Allan <bruce.w.allan@intel.com>

When data blocks are written to the EEPROM, the HW/SW/FW semaphore must be
held for the duration.  With large data blocks on 80003es2lan, 82571 and
82572, this can take too long and cause the firmware to take ownership of
the semaphore and consequently ownership of writes to the EEPROM.
Instead, acquire and release the semaphore for each page of the block
written.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/nvm.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/nvm.c b/drivers/net/ethernet/intel/e1000e/nvm.c
index b646880..71938ed 100644
--- a/drivers/net/ethernet/intel/e1000e/nvm.c
+++ b/drivers/net/ethernet/intel/e1000e/nvm.c
@@ -359,7 +359,7 @@ s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 {
 	struct e1000_nvm_info *nvm = &hw->nvm;
-	s32 ret_val;
+	s32 ret_val = -E1000_ERR_NVM;
 	u16 widx = 0;
 
 	/* A check for invalid values:  offset too large, too many words,
@@ -371,16 +371,18 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 		return -E1000_ERR_NVM;
 	}
 
-	ret_val = nvm->ops.acquire(hw);
-	if (ret_val)
-		return ret_val;
-
 	while (widx < words) {
 		u8 write_opcode = NVM_WRITE_OPCODE_SPI;
 
-		ret_val = e1000_ready_nvm_eeprom(hw);
+		ret_val = nvm->ops.acquire(hw);
 		if (ret_val)
-			goto release;
+			return ret_val;
+
+		ret_val = e1000_ready_nvm_eeprom(hw);
+		if (ret_val) {
+			nvm->ops.release(hw);
+			return ret_val;
+		}
 
 		e1000_standby_nvm(hw);
 
@@ -413,12 +415,10 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 				break;
 			}
 		}
+		usleep_range(10000, 20000);
+		nvm->ops.release(hw);
 	}
 
-	usleep_range(10000, 20000);
-release:
-	nvm->ops.release(hw);
-
 	return ret_val;
 }
 
-- 
1.7.11.7