[net-next 03/15] ixgbe: fix fc autoneg ethtool reporting.

[Jeff Kirsher <jeffrey.t.kirsher@intel.com>]

From: Don Skidmore <donald.c.skidmore@intel.com>

Originally ixgbe_device_supports_autoneg_fc() was only expected to
be called by copper devices.  This would lead to false information
to be displayed via ethtool.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_common.c  | 40 +++++++++++++++++++-----
 drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c |  9 +++---
 2 files changed, 37 insertions(+), 12 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
index 9bcdeb8..3c6859f 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -67,15 +67,39 @@ static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw);
  **/
 s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
 {
+	bool supported = false;
+	ixgbe_link_speed speed;
+	bool link_up;
 
-	switch (hw->device_id) {
-	case IXGBE_DEV_ID_X540T:
-	case IXGBE_DEV_ID_X540T1:
-	case IXGBE_DEV_ID_82599_T3_LOM:
-		return 0;
+	switch (hw->phy.media_type) {
+	case ixgbe_media_type_fiber:
+		hw->mac.ops.check_link(hw, &speed, &link_up, false);
+		/* if link is down, assume supported */
+		if (link_up)
+			supported = speed == IXGBE_LINK_SPEED_1GB_FULL ?
+				true : false;
+		else
+			supported = true;
+		break;
+	case ixgbe_media_type_backplane:
+		supported = true;
+		break;
+	case ixgbe_media_type_copper:
+		/* only some copper devices support flow control autoneg */
+		switch (hw->device_id) {
+		case IXGBE_DEV_ID_82599_T3_LOM:
+		case IXGBE_DEV_ID_X540T:
+		case IXGBE_DEV_ID_X540T1:
+			supported = true;
+			break;
+		default:
+			break;
+		}
 	default:
-		return IXGBE_ERR_FC_NOT_SUPPORTED;
+		break;
 	}
+
+	return supported;
 }
 
 /**
@@ -234,7 +258,7 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw)
 						      IXGBE_GSSR_MAC_CSR_SM);
 
 	} else if ((hw->phy.media_type == ixgbe_media_type_copper) &&
-		    (ixgbe_device_supports_autoneg_fc(hw) == 0)) {
+		    (ixgbe_device_supports_autoneg_fc(hw))) {
 		hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE,
 				      MDIO_MMD_AN, reg_cu);
 	}
@@ -2392,7 +2416,7 @@ void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
 
 	/* Autoneg flow control on copper adapters */
 	case ixgbe_media_type_copper:
-		if (ixgbe_device_supports_autoneg_fc(hw) == 0)
+		if (ixgbe_device_supports_autoneg_fc(hw))
 			ret_val = ixgbe_fc_autoneg_copper(hw);
 		break;
 
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
index 24e2e7a..ae58a92 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
@@ -355,10 +355,11 @@ static void ixgbe_get_pauseparam(struct net_device *netdev,
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
 	struct ixgbe_hw *hw = &adapter->hw;
 
-	if (hw->fc.disable_fc_autoneg)
-		pause->autoneg = 0;
-	else
+	if (ixgbe_device_supports_autoneg_fc(hw) &&
+	    !hw->fc.disable_fc_autoneg)
 		pause->autoneg = 1;
+	else
+		pause->autoneg = 0;
 
 	if (hw->fc.current_mode == ixgbe_fc_rx_pause) {
 		pause->rx_pause = 1;
@@ -384,7 +385,7 @@ static int ixgbe_set_pauseparam(struct net_device *netdev,
 
 	/* some devices do not support autoneg of link flow control */
 	if ((pause->autoneg == AUTONEG_ENABLE) &&
-	    (ixgbe_device_supports_autoneg_fc(hw) != 0))
+	    !ixgbe_device_supports_autoneg_fc(hw))
 		return -EINVAL;
 
 	fc.disable_fc_autoneg = (pause->autoneg != AUTONEG_ENABLE);
-- 
1.7.11.7