[PATCH net-next 00/13] Mellanox ethernet driver update Oct-27-2014

[PATCH net-next 00/13] Mellanox ethernet driver update Oct-27-2014

[Amir Vadai]

Hi,

This patchset introduces some small bug fixes, support in get/set of
vlan offload and get/set/capabilities of the link.

First 7 patches by Saeed, add support in setting/getting link speed and getting
cable capabilities.
Next 2 patches also by Saeed, enable the user to turn rx/tx vlan offloading on
and off.
Jenni fixed a bug in error flow during device initalization.
Ido and Jack fixed some code duplication and errors discovered by static checker.
last patch by me is a fix to make ethtool report the actual rings used by
indirection QP.

Patches were applied and tested against commit 61ed53d ("Merge tag 'ntb-3.18'
of git://github.com/jonmason/ntb")

Thanks,
Amir

Amir Vadai (1):
  net/mlx4_en: Report actual number of rings in indirection table

Eugenia Emantayev (1):
  net/mlx4_en: Move spinlocks and work initalizations to beginning of
    init_netdev

Ido Shamay (1):
  net/mlx4_en: Call napi_synchronize on stop_port

Jack Morgenstein (1):
  net/mlx4_en: Cleanups suggested by clang static checker

Saeed Mahameed (9):
  net/mlx4_core: Introduce mlx4_get_module_info for cable module info
    reading
  ethtool,net/mlx4_en: Cable info, get_module_info/eeprom ethtool
    support
  net/mlx4_core: Introduce ACCESS_REG CMD and eth_prot_ctrl dev cap
  net/mlx4_core: Add ethernet backplane autoneg device capability
  ethtool,net/mlx4_en: Add 100M, 20G, 56G speeds ethtool reporting
    support
  net/mlx4_en: Use PTYS register to query ethtool settings
  net/mlx4_en: Use PTYS register to set ethtool settings (Speed)
  net/mlx4_en: Add support for setting rxvlan offload OFF/ON
  net/mlx4_en: Add ethtool support for [rx|tx]vlan offload set to OFF/ON

 drivers/net/ethernet/mellanox/mlx4/cmd.c         |   9 +
 drivers/net/ethernet/mellanox/mlx4/en_clock.c    |  46 ---
 drivers/net/ethernet/mellanox/mlx4/en_ethtool.c  | 503 ++++++++++++++++++++++-
 drivers/net/ethernet/mellanox/mlx4/en_main.c     |  12 +-
 drivers/net/ethernet/mellanox/mlx4/en_netdev.c   | 127 +++++-
 drivers/net/ethernet/mellanox/mlx4/en_port.c     |  24 +-
 drivers/net/ethernet/mellanox/mlx4/en_port.h     |  35 +-
 drivers/net/ethernet/mellanox/mlx4/en_rx.c       |   1 -
 drivers/net/ethernet/mellanox/mlx4/en_selftest.c |  12 +-
 drivers/net/ethernet/mellanox/mlx4/fw.c          | 123 +++++-
 drivers/net/ethernet/mellanox/mlx4/mlx4_en.h     |  18 +-
 drivers/net/ethernet/mellanox/mlx4/port.c        | 156 +++++++
 include/linux/mlx4/cmd.h                         |   2 +
 include/linux/mlx4/device.h                      |  71 +++-
 include/uapi/linux/ethtool.h                     |  18 +-
 15 files changed, 1044 insertions(+), 113 deletions(-)

-- 
1.8.3.4

[PATCH net-next 01/13] net/mlx4_core: Introduce mlx4_get_module_info for cable module info reading

[Amir Vadai]

From: Saeed Mahameed <saeedm@mellanox.com>

Added new MAD_IFC command to read cable module info with attribute id (0xFF60).
Update include/linux/mlx4/device.h with function declaration (mlx4_get_module_info)
and the needed defines/enums for future use.

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/port.c | 156 ++++++++++++++++++++++++++++++
 include/linux/mlx4/device.h               |  30 ++++++
 2 files changed, 186 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlx4/port.c b/drivers/net/ethernet/mellanox/mlx4/port.c
index 94eeb2c..30eb1ea 100644
--- a/drivers/net/ethernet/mellanox/mlx4/port.c
+++ b/drivers/net/ethernet/mellanox/mlx4/port.c
@@ -1311,3 +1311,159 @@ int mlx4_get_roce_gid_from_slave(struct mlx4_dev *dev, int port, int slave_id,
 	return 0;
 }
 EXPORT_SYMBOL(mlx4_get_roce_gid_from_slave);
+
+/* Cable Module Info */
+#define MODULE_INFO_MAX_READ 48
+
+#define I2C_ADDR_LOW  0x50
+#define I2C_ADDR_HIGH 0x51
+#define I2C_PAGE_SIZE 256
+
+/* Module Info Data */
+struct mlx4_cable_info {
+	u8	i2c_addr;
+	u8	page_num;
+	__be16	dev_mem_address;
+	__be16	reserved1;
+	__be16	size;
+	__be32	reserved2[2];
+	u8	data[MODULE_INFO_MAX_READ];
+};
+
+enum cable_info_err {
+	 CABLE_INF_INV_PORT      = 0x1,
+	 CABLE_INF_OP_NOSUP      = 0x2,
+	 CABLE_INF_NOT_CONN      = 0x3,
+	 CABLE_INF_NO_EEPRM      = 0x4,
+	 CABLE_INF_PAGE_ERR      = 0x5,
+	 CABLE_INF_INV_ADDR      = 0x6,
+	 CABLE_INF_I2C_ADDR      = 0x7,
+	 CABLE_INF_QSFP_VIO      = 0x8,
+	 CABLE_INF_I2C_BUSY      = 0x9,
+};
+
+#define MAD_STATUS_2_CABLE_ERR(mad_status) ((mad_status >> 8) & 0xFF)
+
+static inline const char *cable_info_mad_err_str(u16 mad_status)
+{
+	u8 err = MAD_STATUS_2_CABLE_ERR(mad_status);
+
+	switch (err) {
+	case CABLE_INF_INV_PORT:
+		return "invalid port selected";
+	case CABLE_INF_OP_NOSUP:
+		return "operation not supported for this port (the port is of type CX4 or internal)";
+	case CABLE_INF_NOT_CONN:
+		return "cable is not connected";
+	case CABLE_INF_NO_EEPRM:
+		return "the connected cable has no EPROM (passive copper cable)";
+	case CABLE_INF_PAGE_ERR:
+		return "page number is greater than 15";
+	case CABLE_INF_INV_ADDR:
+		return "invalid device_address or size (that is, size equals 0 or address+size is greater than 256)";
+	case CABLE_INF_I2C_ADDR:
+		return "invalid I2C slave address";
+	case CABLE_INF_QSFP_VIO:
+		return "at least one cable violates the QSFP specification and ignores the modsel signal";
+	case CABLE_INF_I2C_BUSY:
+		return "I2C bus is constantly busy";
+	}
+	return "Unknown Error";
+}
+
+/**
+ * mlx4_get_module_info - Read cable module eeprom data
+ * @dev: mlx4_dev.
+ * @port: port number.
+ * @offset: byte offset in eeprom to start reading data from.
+ * @size: num of bytes to read.
+ * @data: output buffer to put the requested data into.
+ *
+ * Reads cable module eeprom data, puts the outcome data into
+ * data pointer paramer.
+ * Returns num of read bytes on success or a negative error
+ * code.
+ */
+int mlx4_get_module_info(struct mlx4_dev *dev, u8 port,
+			 u16 offset, u16 size, u8 *data)
+{
+	struct mlx4_cmd_mailbox *inbox, *outbox;
+	struct mlx4_mad_ifc *inmad, *outmad;
+	struct mlx4_cable_info *cable_info;
+	u16 i2c_addr;
+	int ret;
+
+	if (size > MODULE_INFO_MAX_READ)
+		size = MODULE_INFO_MAX_READ;
+
+	inbox = mlx4_alloc_cmd_mailbox(dev);
+	if (IS_ERR(inbox))
+		return PTR_ERR(inbox);
+
+	outbox = mlx4_alloc_cmd_mailbox(dev);
+	if (IS_ERR(outbox)) {
+		mlx4_free_cmd_mailbox(dev, inbox);
+		return PTR_ERR(outbox);
+	}
+
+	inmad = (struct mlx4_mad_ifc *)(inbox->buf);
+	outmad = (struct mlx4_mad_ifc *)(outbox->buf);
+
+	inmad->method = 0x1; /* Get */
+	inmad->class_version = 0x1;
+	inmad->mgmt_class = 0x1;
+	inmad->base_version = 0x1;
+	inmad->attr_id = cpu_to_be16(0xFF60); /* Module Info */
+
+	if (offset < I2C_PAGE_SIZE && offset + size > I2C_PAGE_SIZE)
+		/* Cross pages reads are not allowed
+		 * read until offset 256 in low page
+		 */
+		size -= offset + size - I2C_PAGE_SIZE;
+
+	i2c_addr = I2C_ADDR_LOW;
+	if (offset >= I2C_PAGE_SIZE) {
+		/* Reset offset to high page */
+		i2c_addr = I2C_ADDR_HIGH;
+		offset -= I2C_PAGE_SIZE;
+	}
+
+	cable_info = (struct mlx4_cable_info *)inmad->data;
+	cable_info->dev_mem_address = cpu_to_be16(offset);
+	cable_info->page_num = 0;
+	cable_info->i2c_addr = i2c_addr;
+	cable_info->size = cpu_to_be16(size);
+
+	ret = mlx4_cmd_box(dev, inbox->dma, outbox->dma, port, 3,
+			   MLX4_CMD_MAD_IFC, MLX4_CMD_TIME_CLASS_C,
+			   MLX4_CMD_NATIVE);
+	if (ret)
+		goto out;
+
+	if (be16_to_cpu(outmad->status)) {
+		/* Mad returned with bad status */
+		ret = be16_to_cpu(outmad->status);
+		mlx4_warn(dev,
+			  "MLX4_CMD_MAD_IFC Get Module info attr(%x) port(%d) i2c_addr(%x) offset(%d) size(%d): Response Mad Status(%x) - %s\n",
+			  0xFF60, port, i2c_addr, offset, size,
+			  ret, cable_info_mad_err_str(ret));
+
+		if (i2c_addr == I2C_ADDR_HIGH &&
+		    MAD_STATUS_2_CABLE_ERR(ret) == CABLE_INF_I2C_ADDR)
+			/* Some SFP cables do not support i2c slave
+			 * address 0x51 (high page), abort silently.
+			 */
+			ret = 0;
+		else
+			ret = -ret;
+		goto out;
+	}
+	cable_info = (struct mlx4_cable_info *)outmad->data;
+	memcpy(data, cable_info->data, size);
+	ret = size;
+out:
+	mlx4_free_cmd_mailbox(dev, inbox);
+	mlx4_free_cmd_mailbox(dev, outbox);
+	return ret;
+}
+EXPORT_SYMBOL(mlx4_get_module_info);
diff --git a/include/linux/mlx4/device.h b/include/linux/mlx4/device.h
index 37e4404..73910da 100644
--- a/include/linux/mlx4/device.h
+++ b/include/linux/mlx4/device.h
@@ -379,6 +379,13 @@ enum {
 #define MSTR_SM_CHANGE_MASK (MLX4_EQ_PORT_INFO_MSTR_SM_SL_CHANGE_MASK | \
 			     MLX4_EQ_PORT_INFO_MSTR_SM_LID_CHANGE_MASK)
 
+enum mlx4_module_id {
+	MLX4_MODULE_ID_SFP              = 0x3,
+	MLX4_MODULE_ID_QSFP             = 0xC,
+	MLX4_MODULE_ID_QSFP_PLUS        = 0xD,
+	MLX4_MODULE_ID_QSFP28           = 0x11,
+};
+
 static inline u64 mlx4_fw_ver(u64 major, u64 minor, u64 subminor)
 {
 	return (major << 32) | (minor << 16) | subminor;
@@ -799,6 +806,26 @@ struct mlx4_init_port_param {
 	u64			si_guid;
 };
 
+#define MAD_IFC_DATA_SZ 192
+/* MAD IFC Mailbox */
+struct mlx4_mad_ifc {
+	u8	base_version;
+	u8	mgmt_class;
+	u8	class_version;
+	u8	method;
+	__be16	status;
+	__be16	class_specific;
+	__be64	tid;
+	__be16	attr_id;
+	__be16	resv;
+	__be32	attr_mod;
+	__be64	mkey;
+	__be16	dr_slid;
+	__be16	dr_dlid;
+	u8	reserved[28];
+	u8	data[MAD_IFC_DATA_SZ];
+} __packed;
+
 #define mlx4_foreach_port(port, dev, type)				\
 	for ((port) = 1; (port) <= (dev)->caps.num_ports; (port)++)	\
 		if ((type) == (dev)->caps.port_mask[(port)])
@@ -1283,6 +1310,9 @@ int mlx4_mr_rereg_mem_write(struct mlx4_dev *dev, struct mlx4_mr *mr,
 			    u64 iova, u64 size, int npages,
 			    int page_shift, struct mlx4_mpt_entry *mpt_entry);
 
+int mlx4_get_module_info(struct mlx4_dev *dev, u8 port,
+			 u16 offset, u16 size, u8 *data);
+
 /* Returns true if running in low memory profile (kdump kernel) */
 static inline bool mlx4_low_memory_profile(void)
 {
-- 
1.8.3.4

[PATCH net-next 02/13] ethtool,net/mlx4_en: Cable info, get_module_info/eeprom ethtool support

[Amir Vadai]

From: Saeed Mahameed <saeedm@mellanox.com>

Added support for get_module_info/get_module_eeprom ethtool support for cable info reading.

Added new cable types enum in include/uapi/linux/ethtool.h for ethtool use.
+#define ETH_MODULE_SFF_8636            0x3
+#define ETH_MODULE_SFF_8636_LEN        256
+#define ETH_MODULE_SFF_8436            0x4
+#define ETH_MODULE_SFF_8436_LEN        256

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/en_ethtool.c | 83 +++++++++++++++++++++++++
 include/uapi/linux/ethtool.h                    |  4 ++
 2 files changed, 87 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
index ae83da9..279f423 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
@@ -35,6 +35,7 @@
 #include <linux/ethtool.h>
 #include <linux/netdevice.h>
 #include <linux/mlx4/driver.h>
+#include <linux/mlx4/device.h>
 #include <linux/in.h>
 #include <net/ip.h>
 
@@ -1309,6 +1310,86 @@ static int mlx4_en_set_tunable(struct net_device *dev,
 	return ret;
 }
 
+static int mlx4_en_get_module_info(struct net_device *dev,
+				   struct ethtool_modinfo *modinfo)
+{
+	struct mlx4_en_priv *priv = netdev_priv(dev);
+	struct mlx4_en_dev *mdev = priv->mdev;
+	int ret;
+	u8 data[4];
+
+	/* Read first 2 bytes to get Module & REV ID */
+	ret = mlx4_get_module_info(mdev->dev, priv->port,
+				   0/*offset*/, 2/*size*/, data);
+	if (ret < 2)
+		return -EIO;
+
+	switch (data[0] /* identifier */) {
+	case MLX4_MODULE_ID_QSFP:
+		modinfo->type = ETH_MODULE_SFF_8436;
+		modinfo->eeprom_len = ETH_MODULE_SFF_8436_LEN;
+		break;
+	case MLX4_MODULE_ID_QSFP_PLUS:
+		if (data[1] >= 0x3) { /* revision id */
+			modinfo->type = ETH_MODULE_SFF_8636;
+			modinfo->eeprom_len = ETH_MODULE_SFF_8636_LEN;
+		} else {
+			modinfo->type = ETH_MODULE_SFF_8436;
+			modinfo->eeprom_len = ETH_MODULE_SFF_8436_LEN;
+		}
+		break;
+	case MLX4_MODULE_ID_QSFP28:
+		modinfo->type = ETH_MODULE_SFF_8636;
+		modinfo->eeprom_len = ETH_MODULE_SFF_8636_LEN;
+		break;
+	case MLX4_MODULE_ID_SFP:
+		modinfo->type = ETH_MODULE_SFF_8472;
+		modinfo->eeprom_len = ETH_MODULE_SFF_8472_LEN;
+		break;
+	default:
+		return -ENOSYS;
+	}
+
+	return 0;
+}
+
+static int mlx4_en_get_module_eeprom(struct net_device *dev,
+				     struct ethtool_eeprom *ee,
+				     u8 *data)
+{
+	struct mlx4_en_priv *priv = netdev_priv(dev);
+	struct mlx4_en_dev *mdev = priv->mdev;
+	int offset = ee->offset;
+	int i = 0, ret;
+
+	if (ee->len == 0)
+		return -EINVAL;
+
+	memset(data, 0, ee->len);
+
+	while (i < ee->len) {
+		en_dbg(DRV, priv,
+		       "mlx4_get_module_info i(%d) offset(%d) len(%d)\n",
+		       i, offset, ee->len - i);
+
+		ret = mlx4_get_module_info(mdev->dev, priv->port,
+					   offset, ee->len - i, data + i);
+
+		if (!ret) /* Done reading */
+			return 0;
+
+		if (ret < 0) {
+			en_err(priv,
+			       "mlx4_get_module_info i(%d) offset(%d) bytes_to_read(%d) - FAILED (0x%x)\n",
+			       i, offset, ee->len - i, ret);
+			return 0;
+		}
+
+		i += ret;
+		offset += ret;
+	}
+	return 0;
+}
 
 const struct ethtool_ops mlx4_en_ethtool_ops = {
 	.get_drvinfo = mlx4_en_get_drvinfo,
@@ -1341,6 +1422,8 @@ const struct ethtool_ops mlx4_en_ethtool_ops = {
 	.get_priv_flags = mlx4_en_get_priv_flags,
 	.get_tunable		= mlx4_en_get_tunable,
 	.set_tunable		= mlx4_en_set_tunable,
+	.get_module_info = mlx4_en_get_module_info,
+	.get_module_eeprom = mlx4_en_get_module_eeprom
 };
 
 
diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h
index 99b4305..b6acd78 100644
--- a/include/uapi/linux/ethtool.h
+++ b/include/uapi/linux/ethtool.h
@@ -1343,6 +1343,10 @@ enum ethtool_sfeatures_retval_bits {
 #define ETH_MODULE_SFF_8079_LEN		256
 #define ETH_MODULE_SFF_8472		0x2
 #define ETH_MODULE_SFF_8472_LEN		512
+#define ETH_MODULE_SFF_8636		0x3
+#define ETH_MODULE_SFF_8636_LEN		256
+#define ETH_MODULE_SFF_8436		0x4
+#define ETH_MODULE_SFF_8436_LEN		256
 
 /* Reset flags */
 /* The reset() operation must clear the flags for the components which
-- 
1.8.3.4

[PATCH net-next 03/13] net/mlx4_core: Introduce ACCESS_REG CMD and eth_prot_ctrl dev cap

[Amir Vadai]

From: Saeed Mahameed <saeedm@mellanox.com>

Adding ACCESS REG mlx4 command and use it to implement Query method for
PTYS (Port Type and Speed Register).
Query and store eth_prot_ctrl dev cap.

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/cmd.c |   9 +++
 drivers/net/ethernet/mellanox/mlx4/fw.c  | 118 ++++++++++++++++++++++++++++++-
 include/linux/mlx4/cmd.h                 |   2 +
 include/linux/mlx4/device.h              |  40 ++++++++++-
 4 files changed, 166 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/cmd.c b/drivers/net/ethernet/mellanox/mlx4/cmd.c
index b16e1b9..916459e 100644
--- a/drivers/net/ethernet/mellanox/mlx4/cmd.c
+++ b/drivers/net/ethernet/mellanox/mlx4/cmd.c
@@ -1338,6 +1338,15 @@ static struct mlx4_cmd_info cmd_info[] = {
 		.verify = NULL,
 		.wrapper = mlx4_QUERY_IF_STAT_wrapper
 	},
+	{
+		.opcode = MLX4_CMD_ACCESS_REG,
+		.has_inbox = true,
+		.has_outbox = true,
+		.out_is_imm = false,
+		.encode_slave_id = false,
+		.verify = NULL,
+		.wrapper = NULL,
+	},
 	/* Native multicast commands are not available for guests */
 	{
 		.opcode = MLX4_CMD_QP_ATTACH,
diff --git a/drivers/net/ethernet/mellanox/mlx4/fw.c b/drivers/net/ethernet/mellanox/mlx4/fw.c
index 2e88a23..6fd9b85 100644
--- a/drivers/net/ethernet/mellanox/mlx4/fw.c
+++ b/drivers/net/ethernet/mellanox/mlx4/fw.c
@@ -139,7 +139,8 @@ static void dump_dev_cap_flags2(struct mlx4_dev *dev, u64 flags)
 		[10] = "TCP/IP offloads/flow-steering for VXLAN support",
 		[11] = "MAD DEMUX (Secure-Host) support",
 		[12] = "Large cache line (>64B) CQE stride support",
-		[13] = "Large cache line (>64B) EQE stride support"
+		[13] = "Large cache line (>64B) EQE stride support",
+		[14] = "Ethernet protocol control support"
 	};
 	int i;
 
@@ -560,6 +561,7 @@ int mlx4_QUERY_DEV_CAP(struct mlx4_dev *dev, struct mlx4_dev_cap *dev_cap)
 #define QUERY_DEV_CAP_FLOW_STEERING_RANGE_EN_OFFSET	0x76
 #define QUERY_DEV_CAP_FLOW_STEERING_MAX_QP_OFFSET	0x77
 #define QUERY_DEV_CAP_CQ_EQ_CACHE_LINE_STRIDE	0x7a
+#define QUERY_DEV_CAP_ETH_PROT_CTRL_OFFSET	0x7a
 #define QUERY_DEV_CAP_RDMARC_ENTRY_SZ_OFFSET	0x80
 #define QUERY_DEV_CAP_QPC_ENTRY_SZ_OFFSET	0x82
 #define QUERY_DEV_CAP_AUX_ENTRY_SZ_OFFSET	0x84
@@ -737,11 +739,12 @@ int mlx4_QUERY_DEV_CAP(struct mlx4_dev *dev, struct mlx4_dev_cap *dev_cap)
 	MLX4_GET(size, outbox, QUERY_DEV_CAP_MAX_DESC_SZ_RQ_OFFSET);
 	dev_cap->max_rq_desc_sz = size;
 	MLX4_GET(field, outbox, QUERY_DEV_CAP_CQ_EQ_CACHE_LINE_STRIDE);
+	if (field & (1 << 5))
+		dev_cap->flags2 |= MLX4_DEV_CAP_FLAG2_ETH_PROT_CTRL;
 	if (field & (1 << 6))
 		dev_cap->flags2 |= MLX4_DEV_CAP_FLAG2_CQE_STRIDE;
 	if (field & (1 << 7))
 		dev_cap->flags2 |= MLX4_DEV_CAP_FLAG2_EQE_STRIDE;
-
 	MLX4_GET(dev_cap->bmme_flags, outbox,
 		 QUERY_DEV_CAP_BMME_FLAGS_OFFSET);
 	MLX4_GET(dev_cap->reserved_lkey, outbox,
@@ -2144,3 +2147,114 @@ out:
 	mlx4_free_cmd_mailbox(dev, mailbox);
 	return err;
 }
+
+/* Access Reg commands */
+enum mlx4_access_reg_masks {
+	MLX4_ACCESS_REG_STATUS_MASK = 0x7f,
+	MLX4_ACCESS_REG_METHOD_MASK = 0x7f,
+	MLX4_ACCESS_REG_LEN_MASK = 0x7ff
+};
+
+struct mlx4_access_reg {
+	__be16 constant1;
+	u8 status;
+	u8 resrvd1;
+	__be16 reg_id;
+	u8 method;
+	u8 constant2;
+	__be32 resrvd2[2];
+	__be16 len_const;
+	__be16 resrvd3;
+#define MLX4_ACCESS_REG_HEADER_SIZE (20)
+	u8 reg_data[MLX4_MAILBOX_SIZE-MLX4_ACCESS_REG_HEADER_SIZE];
+} __attribute__((__packed__));
+
+/**
+ * mlx4_ACCESS_REG - Generic access reg command.
+ * @dev: mlx4_dev.
+ * @reg_id: register ID to access.
+ * @method: Access method Read/Write.
+ * @reg_len: register length to Read/Write in bytes.
+ * @reg_data: reg_data pointer to Read/Write From/To.
+ *
+ * Access ConnectX registers FW command.
+ * Returns 0 on success and copies outbox mlx4_access_reg data
+ * field into reg_data or a negative error code.
+ */
+static int mlx4_ACCESS_REG(struct mlx4_dev *dev, u16 reg_id,
+			   enum mlx4_access_reg_method method,
+			   u16 reg_len, void *reg_data)
+{
+	struct mlx4_cmd_mailbox *inbox, *outbox;
+	struct mlx4_access_reg *inbuf, *outbuf;
+	int err;
+
+	inbox = mlx4_alloc_cmd_mailbox(dev);
+	if (IS_ERR(inbox))
+		return PTR_ERR(inbox);
+
+	outbox = mlx4_alloc_cmd_mailbox(dev);
+	if (IS_ERR(outbox)) {
+		mlx4_free_cmd_mailbox(dev, inbox);
+		return PTR_ERR(outbox);
+	}
+
+	inbuf = inbox->buf;
+	outbuf = outbox->buf;
+
+	inbuf->constant1 = cpu_to_be16(0x1<<11 | 0x4);
+	inbuf->constant2 = 0x1;
+	inbuf->reg_id = cpu_to_be16(reg_id);
+	inbuf->method = method & MLX4_ACCESS_REG_METHOD_MASK;
+
+	reg_len = min(reg_len, (u16)(sizeof(inbuf->reg_data)));
+	inbuf->len_const =
+		cpu_to_be16(((reg_len/4 + 1) & MLX4_ACCESS_REG_LEN_MASK) |
+			    ((0x3) << 12));
+
+	memcpy(inbuf->reg_data, reg_data, reg_len);
+	err = mlx4_cmd_box(dev, inbox->dma, outbox->dma, 0, 0,
+			   MLX4_CMD_ACCESS_REG, MLX4_CMD_TIME_CLASS_C,
+			   MLX4_CMD_NATIVE);
+	if (err)
+		goto out;
+
+	if (outbuf->status & MLX4_ACCESS_REG_STATUS_MASK) {
+		err = outbuf->status & MLX4_ACCESS_REG_STATUS_MASK;
+		mlx4_err(dev,
+			 "MLX4_CMD_ACCESS_REG(%x) returned REG status (%x)\n",
+			 reg_id, err);
+		goto out;
+	}
+
+	memcpy(reg_data, outbuf->reg_data, reg_len);
+out:
+	mlx4_free_cmd_mailbox(dev, inbox);
+	mlx4_free_cmd_mailbox(dev, outbox);
+	return err;
+}
+
+/* ConnectX registers IDs */
+enum mlx4_reg_id {
+	MLX4_REG_ID_PTYS = 0x5004,
+};
+
+/**
+ * mlx4_ACCESS_PTYS_REG - Access PTYs (Port Type and Speed)
+ * register
+ * @dev: mlx4_dev.
+ * @method: Access method Read/Write.
+ * @ptys_reg: PTYS register data pointer.
+ *
+ * Access ConnectX PTYS register, to Read/Write Port Type/Speed
+ * configuration
+ * Returns 0 on success or a negative error code.
+ */
+int mlx4_ACCESS_PTYS_REG(struct mlx4_dev *dev,
+			 enum mlx4_access_reg_method method,
+			 struct mlx4_ptys_reg *ptys_reg)
+{
+	return mlx4_ACCESS_REG(dev, MLX4_REG_ID_PTYS,
+			       method, sizeof(*ptys_reg), ptys_reg);
+}
+EXPORT_SYMBOL_GPL(mlx4_ACCESS_PTYS_REG);
diff --git a/include/linux/mlx4/cmd.h b/include/linux/mlx4/cmd.h
index 379c026..ff5f5de 100644
--- a/include/linux/mlx4/cmd.h
+++ b/include/linux/mlx4/cmd.h
@@ -67,6 +67,8 @@ enum {
 	MLX4_CMD_MAP_ICM_AUX	 = 0xffc,
 	MLX4_CMD_UNMAP_ICM_AUX	 = 0xffb,
 	MLX4_CMD_SET_ICM_SIZE	 = 0xffd,
+	MLX4_CMD_ACCESS_REG	 = 0x3b,
+
 	/*master notify fw on finish for slave's flr*/
 	MLX4_CMD_INFORM_FLR_DONE = 0x5b,
 	MLX4_CMD_GET_OP_REQ      = 0x59,
diff --git a/include/linux/mlx4/device.h b/include/linux/mlx4/device.h
index 73910da..181cd9f 100644
--- a/include/linux/mlx4/device.h
+++ b/include/linux/mlx4/device.h
@@ -186,7 +186,8 @@ enum {
 	MLX4_DEV_CAP_FLAG2_VXLAN_OFFLOADS	= 1LL <<  10,
 	MLX4_DEV_CAP_FLAG2_MAD_DEMUX		= 1LL <<  11,
 	MLX4_DEV_CAP_FLAG2_CQE_STRIDE		= 1LL <<  12,
-	MLX4_DEV_CAP_FLAG2_EQE_STRIDE		= 1LL <<  13
+	MLX4_DEV_CAP_FLAG2_EQE_STRIDE		= 1LL <<  13,
+	MLX4_DEV_CAP_FLAG2_ETH_PROT_CTRL        = 1LL <<  14
 };
 
 enum {
@@ -1319,4 +1320,41 @@ static inline bool mlx4_low_memory_profile(void)
 	return is_kdump_kernel();
 }
 
+/* ACCESS REG commands */
+enum mlx4_access_reg_method {
+	MLX4_ACCESS_REG_QUERY = 0x1,
+	MLX4_ACCESS_REG_WRITE = 0x2,
+};
+
+/* ACCESS PTYS Reg command */
+enum mlx4_ptys_proto {
+	MLX4_PTYS_IB = 1<<0,
+	MLX4_PTYS_EN = 1<<2,
+};
+
+struct mlx4_ptys_reg {
+	u8 resrvd1;
+	u8 local_port;
+	u8 resrvd2;
+	u8 proto_mask;
+	__be32 resrvd3[2];
+	__be32 eth_proto_cap;
+	__be16 ib_width_cap;
+	__be16 ib_speed_cap;
+	__be32 resrvd4;
+	__be32 eth_proto_admin;
+	__be16 ib_width_admin;
+	__be16 ib_speed_admin;
+	__be32 resrvd5;
+	__be32 eth_proto_oper;
+	__be16 ib_width_oper;
+	__be16 ib_speed_oper;
+	__be32 resrvd6;
+	__be32 eth_proto_lp_adv;
+} __packed;
+
+int mlx4_ACCESS_PTYS_REG(struct mlx4_dev *dev,
+			 enum mlx4_access_reg_method method,
+			 struct mlx4_ptys_reg *ptys_reg);
+
 #endif /* MLX4_DEVICE_H */
-- 
1.8.3.4

[PATCH net-next 04/13] net/mlx4_core: Add ethernet backplane autoneg device capability

[Amir Vadai]

From: Saeed Mahameed <saeedm@mellanox.com>

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/fw.c | 7 ++++++-
 include/linux/mlx4/device.h             | 3 ++-
 2 files changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/fw.c b/drivers/net/ethernet/mellanox/mlx4/fw.c
index 6fd9b85..72289ef 100644
--- a/drivers/net/ethernet/mellanox/mlx4/fw.c
+++ b/drivers/net/ethernet/mellanox/mlx4/fw.c
@@ -140,7 +140,8 @@ static void dump_dev_cap_flags2(struct mlx4_dev *dev, u64 flags)
 		[11] = "MAD DEMUX (Secure-Host) support",
 		[12] = "Large cache line (>64B) CQE stride support",
 		[13] = "Large cache line (>64B) EQE stride support",
-		[14] = "Ethernet protocol control support"
+		[14] = "Ethernet protocol control support",
+		[15] = "Ethernet Backplane autoneg support"
 	};
 	int i;
 
@@ -575,6 +576,7 @@ int mlx4_QUERY_DEV_CAP(struct mlx4_dev *dev, struct mlx4_dev_cap *dev_cap)
 #define QUERY_DEV_CAP_BMME_FLAGS_OFFSET		0x94
 #define QUERY_DEV_CAP_RSVD_LKEY_OFFSET		0x98
 #define QUERY_DEV_CAP_MAX_ICM_SZ_OFFSET		0xa0
+#define QUERY_DEV_CAP_ETH_BACKPL_OFFSET		0x9c
 #define QUERY_DEV_CAP_FW_REASSIGN_MAC		0x9d
 #define QUERY_DEV_CAP_VXLAN			0x9e
 #define QUERY_DEV_CAP_MAD_DEMUX_OFFSET		0xb0
@@ -749,6 +751,9 @@ int mlx4_QUERY_DEV_CAP(struct mlx4_dev *dev, struct mlx4_dev_cap *dev_cap)
 		 QUERY_DEV_CAP_BMME_FLAGS_OFFSET);
 	MLX4_GET(dev_cap->reserved_lkey, outbox,
 		 QUERY_DEV_CAP_RSVD_LKEY_OFFSET);
+	MLX4_GET(field32, outbox, QUERY_DEV_CAP_ETH_BACKPL_OFFSET);
+	if (field32 & (1 << 0))
+		dev_cap->flags2 |= MLX4_DEV_CAP_FLAG2_ETH_BACKPL_AN_REP;
 	MLX4_GET(field, outbox, QUERY_DEV_CAP_FW_REASSIGN_MAC);
 	if (field & 1<<6)
 		dev_cap->flags2 |= MLX4_DEV_CAP_FLAG2_REASSIGN_MAC_EN;
diff --git a/include/linux/mlx4/device.h b/include/linux/mlx4/device.h
index 181cd9f..e4c136e 100644
--- a/include/linux/mlx4/device.h
+++ b/include/linux/mlx4/device.h
@@ -187,7 +187,8 @@ enum {
 	MLX4_DEV_CAP_FLAG2_MAD_DEMUX		= 1LL <<  11,
 	MLX4_DEV_CAP_FLAG2_CQE_STRIDE		= 1LL <<  12,
 	MLX4_DEV_CAP_FLAG2_EQE_STRIDE		= 1LL <<  13,
-	MLX4_DEV_CAP_FLAG2_ETH_PROT_CTRL        = 1LL <<  14
+	MLX4_DEV_CAP_FLAG2_ETH_PROT_CTRL        = 1LL <<  14,
+	MLX4_DEV_CAP_FLAG2_ETH_BACKPL_AN_REP	= 1LL <<  15
 };
 
 enum {
-- 
1.8.3.4

[PATCH net-next 05/13] ethtool,net/mlx4_en: Add 100M, 20G, 56G speeds ethtool reporting support

[Amir Vadai]

From: Saeed Mahameed <saeedm@mellanox.com>

Added 100M, 20G and 56G ethtool speed reporting support.
Update mlx4_en_test_speed self test with the new speeds.

Defined new link speeds in include/uapi/linux/ethtool.h:
+#define SPEED_20000	20000
+#define SPEED_40000	40000
+#define SPEED_56000	56000

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/en_port.c     | 15 ++++++++++++---
 drivers/net/ethernet/mellanox/mlx4/en_port.h     |  9 ++++++---
 drivers/net/ethernet/mellanox/mlx4/en_selftest.c | 12 ++++++++----
 include/uapi/linux/ethtool.h                     | 14 +++++++++++++-
 4 files changed, 39 insertions(+), 11 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/en_port.c b/drivers/net/ethernet/mellanox/mlx4/en_port.c
index 0a0261d..afd3036 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_port.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_port.c
@@ -91,15 +91,24 @@ int mlx4_en_QUERY_PORT(struct mlx4_en_dev *mdev, u8 port)
 	 * already synchronized, no need in locking */
 	state->link_state = !!(qport_context->link_up & MLX4_EN_LINK_UP_MASK);
 	switch (qport_context->link_speed & MLX4_EN_SPEED_MASK) {
+	case MLX4_EN_100M_SPEED:
+		state->link_speed = SPEED_100;
+		break;
 	case MLX4_EN_1G_SPEED:
-		state->link_speed = 1000;
+		state->link_speed = SPEED_1000;
 		break;
 	case MLX4_EN_10G_SPEED_XAUI:
 	case MLX4_EN_10G_SPEED_XFI:
-		state->link_speed = 10000;
+		state->link_speed = SPEED_10000;
+		break;
+	case MLX4_EN_20G_SPEED:
+		state->link_speed = SPEED_20000;
 		break;
 	case MLX4_EN_40G_SPEED:
-		state->link_speed = 40000;
+		state->link_speed = SPEED_40000;
+		break;
+	case MLX4_EN_56G_SPEED:
+		state->link_speed = SPEED_56000;
 		break;
 	default:
 		state->link_speed = -1;
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_port.h b/drivers/net/ethernet/mellanox/mlx4/en_port.h
index 745090b..a5fc93b 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_port.h
+++ b/drivers/net/ethernet/mellanox/mlx4/en_port.h
@@ -54,10 +54,13 @@ enum {
 };
 
 enum {
-	MLX4_EN_1G_SPEED	= 0x02,
-	MLX4_EN_10G_SPEED_XFI	= 0x01,
+	MLX4_EN_100M_SPEED	= 0x04,
 	MLX4_EN_10G_SPEED_XAUI	= 0x00,
+	MLX4_EN_10G_SPEED_XFI	= 0x01,
+	MLX4_EN_1G_SPEED	= 0x02,
+	MLX4_EN_20G_SPEED	= 0x08,
 	MLX4_EN_40G_SPEED	= 0x40,
+	MLX4_EN_56G_SPEED	= 0x20,
 	MLX4_EN_OTHER_SPEED	= 0x0f,
 };
 
@@ -68,7 +71,7 @@ struct mlx4_en_query_port_context {
 	__be16 mtu;
 	u8 reserved2;
 	u8 link_speed;
-#define MLX4_EN_SPEED_MASK	0x43
+#define MLX4_EN_SPEED_MASK	0x6f
 	u16 reserved3[5];
 	__be64 mac;
 	u8 transceiver;
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_selftest.c b/drivers/net/ethernet/mellanox/mlx4/en_selftest.c
index 49d5afc..2d8ee66 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_selftest.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_selftest.c
@@ -129,11 +129,15 @@ static int mlx4_en_test_speed(struct mlx4_en_priv *priv)
 	if (mlx4_en_QUERY_PORT(priv->mdev, priv->port))
 		return -ENOMEM;
 
-	/* The device supports 1G, 10G and 40G speeds */
-	if (priv->port_state.link_speed != 1000 &&
-	    priv->port_state.link_speed != 10000 &&
-	    priv->port_state.link_speed != 40000)
+	/* The device supports 100M, 1G, 10G, 20G, 40G and 56G speed */
+	if (priv->port_state.link_speed != SPEED_100 &&
+	    priv->port_state.link_speed != SPEED_1000 &&
+	    priv->port_state.link_speed != SPEED_10000 &&
+	    priv->port_state.link_speed != SPEED_20000 &&
+	    priv->port_state.link_speed != SPEED_40000 &&
+	    priv->port_state.link_speed != SPEED_56000)
 		return priv->port_state.link_speed;
+
 	return 0;
 }
 
diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h
index b6acd78..eb2095b 100644
--- a/include/uapi/linux/ethtool.h
+++ b/include/uapi/linux/ethtool.h
@@ -1213,6 +1213,10 @@ enum ethtool_sfeatures_retval_bits {
 #define SUPPORTED_40000baseCR4_Full	(1 << 24)
 #define SUPPORTED_40000baseSR4_Full	(1 << 25)
 #define SUPPORTED_40000baseLR4_Full	(1 << 26)
+#define SUPPORTED_56000baseKR4_Full	(1 << 27)
+#define SUPPORTED_56000baseCR4_Full	(1 << 28)
+#define SUPPORTED_56000baseSR4_Full	(1 << 29)
+#define SUPPORTED_56000baseLR4_Full	(1 << 30)
 
 #define ADVERTISED_10baseT_Half		(1 << 0)
 #define ADVERTISED_10baseT_Full		(1 << 1)
@@ -1241,6 +1245,10 @@ enum ethtool_sfeatures_retval_bits {
 #define ADVERTISED_40000baseCR4_Full	(1 << 24)
 #define ADVERTISED_40000baseSR4_Full	(1 << 25)
 #define ADVERTISED_40000baseLR4_Full	(1 << 26)
+#define ADVERTISED_56000baseKR4_Full	(1 << 27)
+#define ADVERTISED_56000baseCR4_Full	(1 << 28)
+#define ADVERTISED_56000baseSR4_Full	(1 << 29)
+#define ADVERTISED_56000baseLR4_Full	(1 << 30)
 
 /* The following are all involved in forcing a particular link
  * mode for the device for setting things.  When getting the
@@ -1248,12 +1256,16 @@ enum ethtool_sfeatures_retval_bits {
  * it was forced up into this mode or autonegotiated.
  */
 
-/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */
+/* The forced speed, 10Mb, 100Mb, gigabit, [2.5|10|20|40|56]GbE. */
 #define SPEED_10		10
 #define SPEED_100		100
 #define SPEED_1000		1000
 #define SPEED_2500		2500
 #define SPEED_10000		10000
+#define SPEED_20000		20000
+#define SPEED_40000		40000
+#define SPEED_56000		56000
+
 #define SPEED_UNKNOWN		-1
 
 /* Duplex, half or full. */
-- 
1.8.3.4

[PATCH net-next 06/13] net/mlx4_en: Use PTYS register to query ethtool settings

[Amir Vadai]

From: Saeed Mahameed <saeedm@mellanox.com>

- If dev cap MLX4_DEV_CAP_FLAG2_ETH_PROT_CTRL is ON, query PTYS register to fill ethtool settings.
else use default values.
- Use autoneg port cap and dev backplane autoneg cap to reprort autoneg interface capbilities.
- Fix typo in mlx4_en_port_state struct field (transciver to transceiver).

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/en_ethtool.c | 311 +++++++++++++++++++++++-
 drivers/net/ethernet/mellanox/mlx4/en_port.c    |   9 +-
 drivers/net/ethernet/mellanox/mlx4/en_port.h    |  26 +-
 drivers/net/ethernet/mellanox/mlx4/mlx4_en.h    |   8 +-
 4 files changed, 338 insertions(+), 16 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
index 279f423..64b6743 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
@@ -375,7 +375,277 @@ static void mlx4_en_get_strings(struct net_device *dev,
 	}
 }
 
-static int mlx4_en_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+static u32 mlx4_en_autoneg_get(struct net_device *dev)
+{
+	struct mlx4_en_priv *priv = netdev_priv(dev);
+	struct mlx4_en_dev *mdev = priv->mdev;
+	u32 autoneg = AUTONEG_DISABLE;
+
+	if ((mdev->dev->caps.flags2 & MLX4_DEV_CAP_FLAG2_ETH_BACKPL_AN_REP) &&
+	    (priv->port_state.flags & MLX4_EN_PORT_ANE))
+		autoneg = AUTONEG_ENABLE;
+
+	return autoneg;
+}
+
+static u32 ptys_get_supported_port(struct mlx4_ptys_reg *ptys_reg)
+{
+	u32 eth_proto = be32_to_cpu(ptys_reg->eth_proto_cap);
+
+	if (eth_proto & (MLX4_PROT_MASK(MLX4_10GBASE_T)
+			 | MLX4_PROT_MASK(MLX4_1000BASE_T)
+			 | MLX4_PROT_MASK(MLX4_100BASE_TX))) {
+			return SUPPORTED_TP;
+	}
+
+	if (eth_proto & (MLX4_PROT_MASK(MLX4_10GBASE_CR)
+			 | MLX4_PROT_MASK(MLX4_10GBASE_SR)
+			 | MLX4_PROT_MASK(MLX4_56GBASE_SR4)
+			 | MLX4_PROT_MASK(MLX4_40GBASE_CR4)
+			 | MLX4_PROT_MASK(MLX4_40GBASE_SR4)
+			 | MLX4_PROT_MASK(MLX4_1000BASE_CX_SGMII))) {
+			return SUPPORTED_FIBRE;
+	}
+
+	if (eth_proto & (MLX4_PROT_MASK(MLX4_56GBASE_KR4)
+			 | MLX4_PROT_MASK(MLX4_40GBASE_KR4)
+			 | MLX4_PROT_MASK(MLX4_20GBASE_KR2)
+			 | MLX4_PROT_MASK(MLX4_10GBASE_KR)
+			 | MLX4_PROT_MASK(MLX4_10GBASE_KX4)
+			 | MLX4_PROT_MASK(MLX4_1000BASE_KX))) {
+			return SUPPORTED_Backplane;
+	}
+	return 0;
+}
+
+static u32 ptys_get_active_port(struct mlx4_ptys_reg *ptys_reg)
+{
+	u32 eth_proto = be32_to_cpu(ptys_reg->eth_proto_oper);
+
+	if (!eth_proto) /* link down */
+		eth_proto = be32_to_cpu(ptys_reg->eth_proto_cap);
+
+	if (eth_proto & (MLX4_PROT_MASK(MLX4_10GBASE_T)
+			 | MLX4_PROT_MASK(MLX4_1000BASE_T)
+			 | MLX4_PROT_MASK(MLX4_100BASE_TX))) {
+			return PORT_TP;
+	}
+
+	if (eth_proto & (MLX4_PROT_MASK(MLX4_10GBASE_SR)
+			 | MLX4_PROT_MASK(MLX4_56GBASE_SR4)
+			 | MLX4_PROT_MASK(MLX4_40GBASE_SR4)
+			 | MLX4_PROT_MASK(MLX4_1000BASE_CX_SGMII))) {
+			return PORT_FIBRE;
+	}
+
+	if (eth_proto & (MLX4_PROT_MASK(MLX4_10GBASE_CR)
+			 | MLX4_PROT_MASK(MLX4_56GBASE_CR4)
+			 | MLX4_PROT_MASK(MLX4_40GBASE_CR4))) {
+			return PORT_DA;
+	}
+
+	if (eth_proto & (MLX4_PROT_MASK(MLX4_56GBASE_KR4)
+			 | MLX4_PROT_MASK(MLX4_40GBASE_KR4)
+			 | MLX4_PROT_MASK(MLX4_20GBASE_KR2)
+			 | MLX4_PROT_MASK(MLX4_10GBASE_KR)
+			 | MLX4_PROT_MASK(MLX4_10GBASE_KX4)
+			 | MLX4_PROT_MASK(MLX4_1000BASE_KX))) {
+			return PORT_NONE;
+	}
+	return PORT_OTHER;
+}
+
+#define MLX4_LINK_MODES_SZ \
+	(FIELD_SIZEOF(struct mlx4_ptys_reg, eth_proto_cap) * 8)
+
+enum ethtool_report {
+	SUPPORTED = 0,
+	ADVERTISED = 1,
+	SPEED = 2
+};
+
+/* Translates mlx4 link mode to equivalent ethtool Link modes/speed */
+static u32 ptys2ethtool_map[MLX4_LINK_MODES_SZ][3] = {
+	[MLX4_100BASE_TX] = {
+		SUPPORTED_100baseT_Full,
+		ADVERTISED_100baseT_Full,
+		SPEED_100
+		},
+
+	[MLX4_1000BASE_T] = {
+		SUPPORTED_1000baseT_Full,
+		ADVERTISED_1000baseT_Full,
+		SPEED_1000
+		},
+	[MLX4_1000BASE_CX_SGMII] = {
+		SUPPORTED_1000baseKX_Full,
+		ADVERTISED_1000baseKX_Full,
+		SPEED_1000
+		},
+	[MLX4_1000BASE_KX] = {
+		SUPPORTED_1000baseKX_Full,
+		ADVERTISED_1000baseKX_Full,
+		SPEED_1000
+		},
+
+	[MLX4_10GBASE_T] = {
+		SUPPORTED_10000baseT_Full,
+		ADVERTISED_10000baseT_Full,
+		SPEED_10000
+		},
+	[MLX4_10GBASE_CX4] = {
+		SUPPORTED_10000baseKX4_Full,
+		ADVERTISED_10000baseKX4_Full,
+		SPEED_10000
+		},
+	[MLX4_10GBASE_KX4] = {
+		SUPPORTED_10000baseKX4_Full,
+		ADVERTISED_10000baseKX4_Full,
+		SPEED_10000
+		},
+	[MLX4_10GBASE_KR] = {
+		SUPPORTED_10000baseKR_Full,
+		ADVERTISED_10000baseKR_Full,
+		SPEED_10000
+		},
+	[MLX4_10GBASE_CR] = {
+		SUPPORTED_10000baseKR_Full,
+		ADVERTISED_10000baseKR_Full,
+		SPEED_10000
+		},
+	[MLX4_10GBASE_SR] = {
+		SUPPORTED_10000baseKR_Full,
+		ADVERTISED_10000baseKR_Full,
+		SPEED_10000
+		},
+
+	[MLX4_20GBASE_KR2] = {
+		SUPPORTED_20000baseMLD2_Full | SUPPORTED_20000baseKR2_Full,
+		ADVERTISED_20000baseMLD2_Full | ADVERTISED_20000baseKR2_Full,
+		SPEED_20000
+		},
+
+	[MLX4_40GBASE_CR4] = {
+		SUPPORTED_40000baseCR4_Full,
+		ADVERTISED_40000baseCR4_Full,
+		SPEED_40000
+		},
+	[MLX4_40GBASE_KR4] = {
+		SUPPORTED_40000baseKR4_Full,
+		ADVERTISED_40000baseKR4_Full,
+		SPEED_40000
+		},
+	[MLX4_40GBASE_SR4] = {
+		SUPPORTED_40000baseSR4_Full,
+		ADVERTISED_40000baseSR4_Full,
+		SPEED_40000
+		},
+
+	[MLX4_56GBASE_KR4] = {
+		SUPPORTED_56000baseKR4_Full,
+		ADVERTISED_56000baseKR4_Full,
+		SPEED_56000
+		},
+	[MLX4_56GBASE_CR4] = {
+		SUPPORTED_56000baseCR4_Full,
+		ADVERTISED_56000baseCR4_Full,
+		SPEED_56000
+		},
+	[MLX4_56GBASE_SR4] = {
+		SUPPORTED_56000baseSR4_Full,
+		ADVERTISED_56000baseSR4_Full,
+		SPEED_56000
+		},
+};
+
+static u32 ptys2ethtool_link_modes(u32 eth_proto, enum ethtool_report report)
+{
+	int i;
+	u32 link_modes = 0;
+
+	for (i = 0; i < MLX4_LINK_MODES_SZ; i++) {
+		if (eth_proto & MLX4_PROT_MASK(i))
+			link_modes |= ptys2ethtool_map[i][report];
+	}
+	return link_modes;
+}
+
+static int ethtool_get_ptys_settings(struct net_device *dev,
+				     struct ethtool_cmd *cmd)
+{
+	struct mlx4_en_priv *priv = netdev_priv(dev);
+	struct mlx4_ptys_reg ptys_reg;
+	u32 eth_proto;
+	int ret;
+
+	memset(&ptys_reg, 0, sizeof(ptys_reg));
+	ptys_reg.local_port = priv->port;
+	ptys_reg.proto_mask = MLX4_PTYS_EN;
+	ret = mlx4_ACCESS_PTYS_REG(priv->mdev->dev,
+				   MLX4_ACCESS_REG_QUERY, &ptys_reg);
+	if (ret) {
+		en_warn(priv, "Failed to run mlx4_ACCESS_PTYS_REG status(%x)",
+			ret);
+		return ret;
+	}
+	en_dbg(DRV, priv, "ptys_reg.proto_mask       %x\n",
+	       ptys_reg.proto_mask);
+	en_dbg(DRV, priv, "ptys_reg.eth_proto_cap    %x\n",
+	       be32_to_cpu(ptys_reg.eth_proto_cap));
+	en_dbg(DRV, priv, "ptys_reg.eth_proto_admin  %x\n",
+	       be32_to_cpu(ptys_reg.eth_proto_admin));
+	en_dbg(DRV, priv, "ptys_reg.eth_proto_oper   %x\n",
+	       be32_to_cpu(ptys_reg.eth_proto_oper));
+	en_dbg(DRV, priv, "ptys_reg.eth_proto_lp_adv %x\n",
+	       be32_to_cpu(ptys_reg.eth_proto_lp_adv));
+
+	cmd->supported = 0;
+	cmd->advertising = 0;
+
+	cmd->supported |= ptys_get_supported_port(&ptys_reg);
+
+	eth_proto = be32_to_cpu(ptys_reg.eth_proto_cap);
+	cmd->supported |= ptys2ethtool_link_modes(eth_proto, SUPPORTED);
+
+	eth_proto = be32_to_cpu(ptys_reg.eth_proto_admin);
+	cmd->advertising |= ptys2ethtool_link_modes(eth_proto, ADVERTISED);
+
+	cmd->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
+	cmd->advertising |= (priv->prof->tx_pause) ? ADVERTISED_Pause : 0;
+
+	cmd->advertising |= (priv->prof->tx_pause ^ priv->prof->rx_pause) ?
+		ADVERTISED_Asym_Pause : 0;
+
+	cmd->port = ptys_get_active_port(&ptys_reg);
+	cmd->transceiver = (SUPPORTED_TP & cmd->supported) ?
+		XCVR_EXTERNAL : XCVR_INTERNAL;
+
+	if (mlx4_en_autoneg_get(dev)) {
+		cmd->supported |= SUPPORTED_Autoneg;
+		cmd->advertising |= ADVERTISED_Autoneg;
+	}
+
+	cmd->autoneg = (priv->port_state.flags & MLX4_EN_PORT_ANC) ?
+		AUTONEG_ENABLE : AUTONEG_DISABLE;
+
+	eth_proto = be32_to_cpu(ptys_reg.eth_proto_lp_adv);
+	cmd->lp_advertising = ptys2ethtool_link_modes(eth_proto, ADVERTISED);
+
+	cmd->lp_advertising |= (priv->port_state.flags & MLX4_EN_PORT_ANC) ?
+			ADVERTISED_Autoneg : 0;
+
+	cmd->phy_address = 0;
+	cmd->mdio_support = 0;
+	cmd->maxtxpkt = 0;
+	cmd->maxrxpkt = 0;
+	cmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
+	cmd->eth_tp_mdix_ctrl = ETH_TP_MDI_AUTO;
+
+	return ret;
+}
+
+static void ethtool_get_default_settings(struct net_device *dev,
+					 struct ethtool_cmd *cmd)
 {
 	struct mlx4_en_priv *priv = netdev_priv(dev);
 	int trans_type;
@@ -383,18 +653,7 @@ static int mlx4_en_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 	cmd->autoneg = AUTONEG_DISABLE;
 	cmd->supported = SUPPORTED_10000baseT_Full;
 	cmd->advertising = ADVERTISED_10000baseT_Full;
-
-	if (mlx4_en_QUERY_PORT(priv->mdev, priv->port))
-		return -ENOMEM;
-
-	trans_type = priv->port_state.transciver;
-	if (netif_carrier_ok(dev)) {
-		ethtool_cmd_speed_set(cmd, priv->port_state.link_speed);
-		cmd->duplex = DUPLEX_FULL;
-	} else {
-		ethtool_cmd_speed_set(cmd, SPEED_UNKNOWN);
-		cmd->duplex = DUPLEX_UNKNOWN;
-	}
+	trans_type = priv->port_state.transceiver;
 
 	if (trans_type > 0 && trans_type <= 0xC) {
 		cmd->port = PORT_FIBRE;
@@ -410,6 +669,32 @@ static int mlx4_en_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 		cmd->port = -1;
 		cmd->transceiver = -1;
 	}
+}
+
+static int mlx4_en_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+	struct mlx4_en_priv *priv = netdev_priv(dev);
+	int ret = -EINVAL;
+
+	if (mlx4_en_QUERY_PORT(priv->mdev, priv->port))
+		return -ENOMEM;
+
+	en_dbg(DRV, priv, "query port state.flags ANC(%x) ANE(%x)\n",
+	       priv->port_state.flags & MLX4_EN_PORT_ANC,
+	       priv->port_state.flags & MLX4_EN_PORT_ANE);
+
+	if (priv->mdev->dev->caps.flags2 & MLX4_DEV_CAP_FLAG2_ETH_PROT_CTRL)
+		ret = ethtool_get_ptys_settings(dev, cmd);
+	if (ret) /* ETH PROT CRTL is not supported or PTYS CMD failed */
+		ethtool_get_default_settings(dev, cmd);
+
+	if (netif_carrier_ok(dev)) {
+		ethtool_cmd_speed_set(cmd, priv->port_state.link_speed);
+		cmd->duplex = DUPLEX_FULL;
+	} else {
+		ethtool_cmd_speed_set(cmd, SPEED_UNKNOWN);
+		cmd->duplex = DUPLEX_UNKNOWN;
+	}
 	return 0;
 }
 
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_port.c b/drivers/net/ethernet/mellanox/mlx4/en_port.c
index afd3036..134b12e 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_port.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_port.c
@@ -114,7 +114,14 @@ int mlx4_en_QUERY_PORT(struct mlx4_en_dev *mdev, u8 port)
 		state->link_speed = -1;
 		break;
 	}
-	state->transciver = qport_context->transceiver;
+
+	state->transceiver = qport_context->transceiver;
+
+	state->flags = 0; /* Reset and recalculate the port flags */
+	state->flags |= (qport_context->link_up & MLX4_EN_ANC_MASK) ?
+		MLX4_EN_PORT_ANC : 0;
+	state->flags |= (qport_context->autoneg & MLX4_EN_AUTONEG_MASK) ?
+		MLX4_EN_PORT_ANE : 0;
 
 out:
 	mlx4_free_cmd_mailbox(mdev->dev, mailbox);
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_port.h b/drivers/net/ethernet/mellanox/mlx4/en_port.h
index a5fc93b..040da4b 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_port.h
+++ b/drivers/net/ethernet/mellanox/mlx4/en_port.h
@@ -53,6 +53,28 @@ enum {
 	MLX4_MCAST_ENABLE       = 2,
 };
 
+enum mlx4_link_mode {
+	MLX4_1000BASE_CX_SGMII	 = 0,
+	MLX4_1000BASE_KX	 = 1,
+	MLX4_10GBASE_CX4	 = 2,
+	MLX4_10GBASE_KX4	 = 3,
+	MLX4_10GBASE_KR		 = 4,
+	MLX4_20GBASE_KR2	 = 5,
+	MLX4_40GBASE_CR4	 = 6,
+	MLX4_40GBASE_KR4	 = 7,
+	MLX4_56GBASE_KR4	 = 8,
+	MLX4_10GBASE_CR		 = 12,
+	MLX4_10GBASE_SR		 = 13,
+	MLX4_40GBASE_SR4	 = 15,
+	MLX4_56GBASE_CR4	 = 17,
+	MLX4_56GBASE_SR4	 = 18,
+	MLX4_100BASE_TX		 = 24,
+	MLX4_1000BASE_T		 = 25,
+	MLX4_10GBASE_T		 = 26,
+};
+
+#define MLX4_PROT_MASK(link_mode) (1<<link_mode)
+
 enum {
 	MLX4_EN_100M_SPEED	= 0x04,
 	MLX4_EN_10G_SPEED_XAUI	= 0x00,
@@ -67,7 +89,9 @@ enum {
 struct mlx4_en_query_port_context {
 	u8 link_up;
 #define MLX4_EN_LINK_UP_MASK	0x80
-	u8 reserved;
+#define MLX4_EN_ANC_MASK	0x40
+	u8 autoneg;
+#define MLX4_EN_AUTONEG_MASK	0x80
 	__be16 mtu;
 	u8 reserved2;
 	u8 link_speed;
diff --git a/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h b/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h
index 8fef658..946754e 100644
--- a/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h
+++ b/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h
@@ -421,10 +421,16 @@ struct mlx4_en_rss_map {
 	enum mlx4_qp_state indir_state;
 };
 
+enum mlx4_en_port_flag {
+	MLX4_EN_PORT_ANC = 1<<0, /* Auto-negotiation complete */
+	MLX4_EN_PORT_ANE = 1<<1, /* Auto-negotiation enabled */
+};
+
 struct mlx4_en_port_state {
 	int link_state;
 	int link_speed;
-	int transciver;
+	int transceiver;
+	u32 flags;
 };
 
 struct mlx4_en_pkt_stats {
-- 
1.8.3.4

[PATCH net-next 07/13] net/mlx4_en: Use PTYS register to set ethtool settings (Speed)

[Amir Vadai]

From: Saeed Mahameed <saeedm@mellanox.com>

Added Support to set speed or advertised link modes via ethtool:
ethtool -s <ifname> [speed <speed>] [advertise <link modes>]

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/en_ethtool.c | 108 +++++++++++++++++++++++-
 1 file changed, 104 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
index 64b6743..144d6bd 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
@@ -570,6 +570,31 @@ static u32 ptys2ethtool_link_modes(u32 eth_proto, enum ethtool_report report)
 	return link_modes;
 }
 
+static u32 ethtool2ptys_link_modes(u32 link_modes, enum ethtool_report report)
+{
+	int i;
+	u32 ptys_modes = 0;
+
+	for (i = 0; i < MLX4_LINK_MODES_SZ; i++) {
+		if (ptys2ethtool_map[i][report] & link_modes)
+			ptys_modes |= 1 << i;
+	}
+	return ptys_modes;
+}
+
+/* Convert actual speed (SPEED_XXX) to ptys link modes */
+static u32 speed2ptys_link_modes(u32 speed)
+{
+	int i;
+	u32 ptys_modes = 0;
+
+	for (i = 0; i < MLX4_LINK_MODES_SZ; i++) {
+		if (ptys2ethtool_map[i][SPEED] == speed)
+			ptys_modes |= 1 << i;
+	}
+	return ptys_modes;
+}
+
 static int ethtool_get_ptys_settings(struct net_device *dev,
 				     struct ethtool_cmd *cmd)
 {
@@ -698,14 +723,89 @@ static int mlx4_en_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 	return 0;
 }
 
+/* Calculate PTYS admin according ethtool speed (SPEED_XXX) */
+static __be32 speed_set_ptys_admin(struct mlx4_en_priv *priv, u32 speed,
+				   __be32 proto_cap)
+{
+	__be32 proto_admin = 0;
+
+	if (!speed) { /* Speed = 0 ==> Reset Link modes */
+		proto_admin = proto_cap;
+		en_info(priv, "Speed was set to 0, Reset advertised Link Modes to default (%x)\n",
+			be32_to_cpu(proto_cap));
+	} else {
+		u32 ptys_link_modes = speed2ptys_link_modes(speed);
+
+		proto_admin = cpu_to_be32(ptys_link_modes) & proto_cap;
+		en_info(priv, "Setting Speed to %d\n", speed);
+	}
+	return proto_admin;
+}
+
 static int mlx4_en_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 {
-	if ((cmd->autoneg == AUTONEG_ENABLE) ||
-	    (ethtool_cmd_speed(cmd) != SPEED_10000) ||
-	    (cmd->duplex != DUPLEX_FULL))
+	struct mlx4_en_priv *priv = netdev_priv(dev);
+	struct mlx4_ptys_reg ptys_reg;
+	__be32 proto_admin;
+	int ret;
+
+	u32 ptys_adv = ethtool2ptys_link_modes(cmd->advertising, ADVERTISED);
+	int speed = ethtool_cmd_speed(cmd);
+
+	en_dbg(DRV, priv, "Set Speed=%d adv=0x%x autoneg=%d duplex=%d\n",
+	       speed, cmd->advertising, cmd->autoneg, cmd->duplex);
+
+	if (!(priv->mdev->dev->caps.flags2 & MLX4_DEV_CAP_FLAG2_ETH_PROT_CTRL) ||
+	    (cmd->autoneg == AUTONEG_ENABLE) || (cmd->duplex == DUPLEX_HALF))
 		return -EINVAL;
 
-	/* Nothing to change */
+	memset(&ptys_reg, 0, sizeof(ptys_reg));
+	ptys_reg.local_port = priv->port;
+	ptys_reg.proto_mask = MLX4_PTYS_EN;
+	ret = mlx4_ACCESS_PTYS_REG(priv->mdev->dev,
+				   MLX4_ACCESS_REG_QUERY, &ptys_reg);
+	if (ret) {
+		en_warn(priv, "Failed to QUERY mlx4_ACCESS_PTYS_REG status(%x)\n",
+			ret);
+		return 0;
+	}
+
+	proto_admin = cpu_to_be32(ptys_adv);
+	if (speed >= 0 && speed != priv->port_state.link_speed)
+		/* If speed was set then speed decides :-) */
+		proto_admin = speed_set_ptys_admin(priv, speed,
+						   ptys_reg.eth_proto_cap);
+
+	proto_admin &= ptys_reg.eth_proto_cap;
+
+	if (proto_admin == ptys_reg.eth_proto_admin)
+		return 0; /* Nothing to change */
+
+	if (!proto_admin) {
+		en_warn(priv, "Not supported link mode(s) requested, check supported link modes.\n");
+		return -EINVAL; /* nothing to change due to bad input */
+	}
+
+	en_dbg(DRV, priv, "mlx4_ACCESS_PTYS_REG SET: ptys_reg.eth_proto_admin = 0x%x\n",
+	       be32_to_cpu(proto_admin));
+
+	ptys_reg.eth_proto_admin = proto_admin;
+	ret = mlx4_ACCESS_PTYS_REG(priv->mdev->dev, MLX4_ACCESS_REG_WRITE,
+				   &ptys_reg);
+	if (ret) {
+		en_warn(priv, "Failed to write mlx4_ACCESS_PTYS_REG eth_proto_admin(0x%x) status(0x%x)",
+			be32_to_cpu(ptys_reg.eth_proto_admin), ret);
+		return ret;
+	}
+
+	en_warn(priv, "Port link mode changed, restarting port...\n");
+	mutex_lock(&priv->mdev->state_lock);
+	if (priv->port_up) {
+		mlx4_en_stop_port(dev, 1);
+		if (mlx4_en_start_port(dev))
+			en_err(priv, "Failed restarting port %d\n", priv->port);
+	}
+	mutex_unlock(&priv->mdev->state_lock);
 	return 0;
 }
 
-- 
1.8.3.4

[PATCH net-next 08/13] net/mlx4_en: Add support for setting rxvlan offload OFF/ON

[Amir Vadai]

From: Saeed Mahameed <saeedm@mellanox.com>

Rename mlx4_en_timestamp_config to mlx4_en_reset_config and extend it to support
choosing RX vlan offload configuration.

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/en_clock.c  | 53 ++++++++++++++++++++------
 drivers/net/ethernet/mellanox/mlx4/en_netdev.c |  2 +-
 drivers/net/ethernet/mellanox/mlx4/mlx4_en.h   | 10 +++--
 3 files changed, 50 insertions(+), 15 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/en_clock.c b/drivers/net/ethernet/mellanox/mlx4/en_clock.c
index 57dda95..285fccf 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_clock.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_clock.c
@@ -35,16 +35,26 @@
 
 #include "mlx4_en.h"
 
-int mlx4_en_timestamp_config(struct net_device *dev, int tx_type, int rx_filter)
+int mlx4_en_reset_config(struct net_device *dev,
+			 struct hwtstamp_config ts_config,
+			 netdev_features_t features)
 {
 	struct mlx4_en_priv *priv = netdev_priv(dev);
 	struct mlx4_en_dev *mdev = priv->mdev;
 	int port_up = 0;
 	int err = 0;
 
-	if (priv->hwtstamp_config.tx_type == tx_type &&
-	    priv->hwtstamp_config.rx_filter == rx_filter)
-		return 0;
+	if (priv->hwtstamp_config.tx_type == ts_config.tx_type &&
+	    priv->hwtstamp_config.rx_filter == ts_config.rx_filter &&
+	    !DEV_FEATURE_CHANGED(dev, features, NETIF_F_HW_VLAN_CTAG_RX))
+		return 0; /* Nothing to change */
+
+	if (DEV_FEATURE_CHANGED(dev, features, NETIF_F_HW_VLAN_CTAG_RX) &&
+	    (features & NETIF_F_HW_VLAN_CTAG_RX) &&
+	    (priv->hwtstamp_config.rx_filter != HWTSTAMP_FILTER_NONE)) {
+		en_warn(priv, "Can't turn ON rx vlan offload while time-stamping rx filter is ON\n");
+		return -EINVAL;
+	}
 
 	mutex_lock(&mdev->state_lock);
 	if (priv->port_up) {
@@ -54,15 +64,36 @@ int mlx4_en_timestamp_config(struct net_device *dev, int tx_type, int rx_filter)
 
 	mlx4_en_free_resources(priv);
 
-	en_warn(priv, "Changing Time Stamp configuration\n");
-
-	priv->hwtstamp_config.tx_type = tx_type;
-	priv->hwtstamp_config.rx_filter = rx_filter;
+	en_warn(priv, "Changing device configuration rx filter(%x) rx vlan(%x)\n",
+		ts_config.rx_filter, !!(features & NETIF_F_HW_VLAN_CTAG_RX));
+
+	priv->hwtstamp_config.tx_type = ts_config.tx_type;
+	priv->hwtstamp_config.rx_filter = ts_config.rx_filter;
+
+	if (DEV_FEATURE_CHANGED(dev, features, NETIF_F_HW_VLAN_CTAG_RX)) {
+		if (features & NETIF_F_HW_VLAN_CTAG_RX)
+			dev->features |= NETIF_F_HW_VLAN_CTAG_RX;
+		else
+			dev->features &= ~NETIF_F_HW_VLAN_CTAG_RX;
+	} else if (ts_config.rx_filter == HWTSTAMP_FILTER_NONE) {
+		/* RX time-stamping is OFF, update the RX vlan offload
+		 * to the latest wanted state
+		 */
+		if (dev->wanted_features & NETIF_F_HW_VLAN_CTAG_RX)
+			dev->features |= NETIF_F_HW_VLAN_CTAG_RX;
+		else
+			dev->features &= ~NETIF_F_HW_VLAN_CTAG_RX;
+	}
 
-	if (rx_filter != HWTSTAMP_FILTER_NONE)
+	/* RX vlan offload and RX time-stamping can't co-exist !
+	 * Regardless of the caller's choice,
+	 * Turn Off RX vlan offload in case of time-stamping is ON
+	 */
+	if (ts_config.rx_filter != HWTSTAMP_FILTER_NONE) {
+		if (dev->features & NETIF_F_HW_VLAN_CTAG_RX)
+			en_warn(priv, "Turning off RX vlan offload since RX time-stamping is ON\n");
 		dev->features &= ~NETIF_F_HW_VLAN_CTAG_RX;
-	else
-		dev->features |= NETIF_F_HW_VLAN_CTAG_RX;
+	}
 
 	err = mlx4_en_alloc_resources(priv);
 	if (err) {
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
index f3032fe..c4bd2c7 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
@@ -2157,7 +2157,7 @@ static int mlx4_en_hwtstamp_set(struct net_device *dev, struct ifreq *ifr)
 		return -ERANGE;
 	}
 
-	if (mlx4_en_timestamp_config(dev, config.tx_type, config.rx_filter)) {
+	if (mlx4_en_reset_config(dev, config, dev->features)) {
 		config.tx_type = HWTSTAMP_TX_OFF;
 		config.rx_filter = HWTSTAMP_FILTER_NONE;
 	}
diff --git a/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h b/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h
index 946754e..6beb4d3 100644
--- a/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h
+++ b/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h
@@ -835,6 +835,13 @@ void mlx4_en_cleanup_filters(struct mlx4_en_priv *priv);
 void mlx4_en_ex_selftest(struct net_device *dev, u32 *flags, u64 *buf);
 void mlx4_en_ptp_overflow_check(struct mlx4_en_dev *mdev);
 
+#define DEV_FEATURE_CHANGED(dev, new_features, feature) \
+	((dev->features & feature) ^ (new_features & feature))
+
+int mlx4_en_reset_config(struct net_device *dev,
+			 struct hwtstamp_config ts_config,
+			 netdev_features_t new_features);
+
 /*
  * Functions for time stamping
  */
@@ -844,9 +851,6 @@ void mlx4_en_fill_hwtstamps(struct mlx4_en_dev *mdev,
 			    u64 timestamp);
 void mlx4_en_init_timestamp(struct mlx4_en_dev *mdev);
 void mlx4_en_remove_timestamp(struct mlx4_en_dev *mdev);
-int mlx4_en_timestamp_config(struct net_device *dev,
-			     int tx_type,
-			     int rx_filter);
 
 /* Globals
  */
-- 
1.8.3.4

[PATCH net-next 09/13] net/mlx4_en: Add ethtool support for [rx|tx]vlan offload set to OFF/ON

[Amir Vadai]

From: Saeed Mahameed <saeedm@mellanox.com>

Move mlx4_en_reset_config to en_netdev.c as it now serves more general purpose.
Add support for turning OFF/ON the rx/tx vlan offlad.

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/en_clock.c  | 77 ----------------------
 drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 90 +++++++++++++++++++++++++-
 2 files changed, 89 insertions(+), 78 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/en_clock.c b/drivers/net/ethernet/mellanox/mlx4/en_clock.c
index 285fccf..9990144 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_clock.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_clock.c
@@ -35,83 +35,6 @@
 
 #include "mlx4_en.h"
 
-int mlx4_en_reset_config(struct net_device *dev,
-			 struct hwtstamp_config ts_config,
-			 netdev_features_t features)
-{
-	struct mlx4_en_priv *priv = netdev_priv(dev);
-	struct mlx4_en_dev *mdev = priv->mdev;
-	int port_up = 0;
-	int err = 0;
-
-	if (priv->hwtstamp_config.tx_type == ts_config.tx_type &&
-	    priv->hwtstamp_config.rx_filter == ts_config.rx_filter &&
-	    !DEV_FEATURE_CHANGED(dev, features, NETIF_F_HW_VLAN_CTAG_RX))
-		return 0; /* Nothing to change */
-
-	if (DEV_FEATURE_CHANGED(dev, features, NETIF_F_HW_VLAN_CTAG_RX) &&
-	    (features & NETIF_F_HW_VLAN_CTAG_RX) &&
-	    (priv->hwtstamp_config.rx_filter != HWTSTAMP_FILTER_NONE)) {
-		en_warn(priv, "Can't turn ON rx vlan offload while time-stamping rx filter is ON\n");
-		return -EINVAL;
-	}
-
-	mutex_lock(&mdev->state_lock);
-	if (priv->port_up) {
-		port_up = 1;
-		mlx4_en_stop_port(dev, 1);
-	}
-
-	mlx4_en_free_resources(priv);
-
-	en_warn(priv, "Changing device configuration rx filter(%x) rx vlan(%x)\n",
-		ts_config.rx_filter, !!(features & NETIF_F_HW_VLAN_CTAG_RX));
-
-	priv->hwtstamp_config.tx_type = ts_config.tx_type;
-	priv->hwtstamp_config.rx_filter = ts_config.rx_filter;
-
-	if (DEV_FEATURE_CHANGED(dev, features, NETIF_F_HW_VLAN_CTAG_RX)) {
-		if (features & NETIF_F_HW_VLAN_CTAG_RX)
-			dev->features |= NETIF_F_HW_VLAN_CTAG_RX;
-		else
-			dev->features &= ~NETIF_F_HW_VLAN_CTAG_RX;
-	} else if (ts_config.rx_filter == HWTSTAMP_FILTER_NONE) {
-		/* RX time-stamping is OFF, update the RX vlan offload
-		 * to the latest wanted state
-		 */
-		if (dev->wanted_features & NETIF_F_HW_VLAN_CTAG_RX)
-			dev->features |= NETIF_F_HW_VLAN_CTAG_RX;
-		else
-			dev->features &= ~NETIF_F_HW_VLAN_CTAG_RX;
-	}
-
-	/* RX vlan offload and RX time-stamping can't co-exist !
-	 * Regardless of the caller's choice,
-	 * Turn Off RX vlan offload in case of time-stamping is ON
-	 */
-	if (ts_config.rx_filter != HWTSTAMP_FILTER_NONE) {
-		if (dev->features & NETIF_F_HW_VLAN_CTAG_RX)
-			en_warn(priv, "Turning off RX vlan offload since RX time-stamping is ON\n");
-		dev->features &= ~NETIF_F_HW_VLAN_CTAG_RX;
-	}
-
-	err = mlx4_en_alloc_resources(priv);
-	if (err) {
-		en_err(priv, "Failed reallocating port resources\n");
-		goto out;
-	}
-	if (port_up) {
-		err = mlx4_en_start_port(dev);
-		if (err)
-			en_err(priv, "Failed starting port\n");
-	}
-
-out:
-	mutex_unlock(&mdev->state_lock);
-	netdev_features_change(dev);
-	return err;
-}
-
 /* mlx4_en_read_clock - read raw cycle counter (to be used by time counter)
  */
 static cycle_t mlx4_en_read_clock(const struct cyclecounter *tc)
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
index c4bd2c7..5d60882 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
@@ -2190,6 +2190,16 @@ static int mlx4_en_set_features(struct net_device *netdev,
 		netdev_features_t features)
 {
 	struct mlx4_en_priv *priv = netdev_priv(netdev);
+	int ret = 0;
+
+	if (DEV_FEATURE_CHANGED(netdev, features, NETIF_F_HW_VLAN_CTAG_RX)) {
+		en_info(priv, "Turn %s RX vlan strip offload\n",
+			(features & NETIF_F_HW_VLAN_CTAG_RX) ? "ON" : "OFF");
+		ret = mlx4_en_reset_config(netdev, priv->hwtstamp_config,
+					   features);
+		if (ret)
+			return ret;
+	}
 
 	if (features & NETIF_F_LOOPBACK)
 		priv->ctrl_flags |= cpu_to_be32(MLX4_WQE_CTRL_FORCE_LOOPBACK);
@@ -2559,7 +2569,8 @@ int mlx4_en_init_netdev(struct mlx4_en_dev *mdev, int port,
 	dev->features = dev->hw_features | NETIF_F_HIGHDMA |
 			NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX |
 			NETIF_F_HW_VLAN_CTAG_FILTER;
-	dev->hw_features |= NETIF_F_LOOPBACK;
+	dev->hw_features |= NETIF_F_LOOPBACK |
+			NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX;
 
 	if (mdev->dev->caps.steering_mode ==
 	    MLX4_STEERING_MODE_DEVICE_MANAGED)
@@ -2633,3 +2644,80 @@ out:
 	return err;
 }
 
+int mlx4_en_reset_config(struct net_device *dev,
+			 struct hwtstamp_config ts_config,
+			 netdev_features_t features)
+{
+	struct mlx4_en_priv *priv = netdev_priv(dev);
+	struct mlx4_en_dev *mdev = priv->mdev;
+	int port_up = 0;
+	int err = 0;
+
+	if (priv->hwtstamp_config.tx_type == ts_config.tx_type &&
+	    priv->hwtstamp_config.rx_filter == ts_config.rx_filter &&
+	    !DEV_FEATURE_CHANGED(dev, features, NETIF_F_HW_VLAN_CTAG_RX))
+		return 0; /* Nothing to change */
+
+	if (DEV_FEATURE_CHANGED(dev, features, NETIF_F_HW_VLAN_CTAG_RX) &&
+	    (features & NETIF_F_HW_VLAN_CTAG_RX) &&
+	    (priv->hwtstamp_config.rx_filter != HWTSTAMP_FILTER_NONE)) {
+		en_warn(priv, "Can't turn ON rx vlan offload while time-stamping rx filter is ON\n");
+		return -EINVAL;
+	}
+
+	mutex_lock(&mdev->state_lock);
+	if (priv->port_up) {
+		port_up = 1;
+		mlx4_en_stop_port(dev, 1);
+	}
+
+	mlx4_en_free_resources(priv);
+
+	en_warn(priv, "Changing device configuration rx filter(%x) rx vlan(%x)\n",
+		ts_config.rx_filter, !!(features & NETIF_F_HW_VLAN_CTAG_RX));
+
+	priv->hwtstamp_config.tx_type = ts_config.tx_type;
+	priv->hwtstamp_config.rx_filter = ts_config.rx_filter;
+
+	if (DEV_FEATURE_CHANGED(dev, features, NETIF_F_HW_VLAN_CTAG_RX)) {
+		if (features & NETIF_F_HW_VLAN_CTAG_RX)
+			dev->features |= NETIF_F_HW_VLAN_CTAG_RX;
+		else
+			dev->features &= ~NETIF_F_HW_VLAN_CTAG_RX;
+	} else if (ts_config.rx_filter == HWTSTAMP_FILTER_NONE) {
+		/* RX time-stamping is OFF, update the RX vlan offload
+		 * to the latest wanted state
+		 */
+		if (dev->wanted_features & NETIF_F_HW_VLAN_CTAG_RX)
+			dev->features |= NETIF_F_HW_VLAN_CTAG_RX;
+		else
+			dev->features &= ~NETIF_F_HW_VLAN_CTAG_RX;
+	}
+
+	/* RX vlan offload and RX time-stamping can't co-exist !
+	 * Regardless of the caller's choice,
+	 * Turn Off RX vlan offload in case of time-stamping is ON
+	 */
+	if (ts_config.rx_filter != HWTSTAMP_FILTER_NONE) {
+		if (dev->features & NETIF_F_HW_VLAN_CTAG_RX)
+			en_warn(priv, "Turning off RX vlan offload since RX time-stamping is ON\n");
+		dev->features &= ~NETIF_F_HW_VLAN_CTAG_RX;
+	}
+
+	err = mlx4_en_alloc_resources(priv);
+	if (err) {
+		en_err(priv, "Failed reallocating port resources\n");
+		goto out;
+	}
+	if (port_up) {
+		err = mlx4_en_start_port(dev);
+		if (err)
+			en_err(priv, "Failed starting port\n");
+	}
+
+out:
+	mutex_unlock(&mdev->state_lock);
+	netdev_features_change(dev);
+	return err;
+}
+
-- 
1.8.3.4

[PATCH net-next 10/13] net/mlx4_en: Cleanups suggested by clang static checker

[Amir Vadai]

From: Jack Morgenstein <jackm@dev.mellanox.co.il>

clang flagged the following. All are actually cosmetic cleanups, not really bugs:

drivers/net/ethernet/mellanox/mlx4/en_main.c:233:3: warning: Value stored to 'err' is never read
                err = -ENOMEM;
                ^     ~~~~~~~
drivers/net/ethernet/mellanox/mlx4/en_main.c:293:3: warning: Value stored to 'err' is never read
                err = -ENOMEM;

drivers/net/ethernet/mellanox/mlx4/en_netdev.c:648:16: warning: Assigned value is garbage or undefined
        entry->reg_id = reg_id;
                      ^ ~~~~~~
drivers/net/ethernet/mellanox/mlx4/en_netdev.c:659:2: warning: Function call argument is an uninitialized value
        mlx4_en_uc_steer_release(priv, priv->dev->dev_addr, *qpn, reg_id);
(NOTE: reg_id is only used in the device-managed flow steering path, in which is it always initialized.
 This is not a bug. Cleanup here is therefore cosmetic only).

drivers/net/ethernet/mellanox/mlx4/en_rx.c:122:3: warning: Value stored to 'frag_info' is never read
                frag_info = &priv->frag_info[i];
                ^           ~~~~~~~~~~~~~~~~~~~


Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>

Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/en_main.c   | 12 +++---------
 drivers/net/ethernet/mellanox/mlx4/en_netdev.c |  2 +-
 drivers/net/ethernet/mellanox/mlx4/en_rx.c     |  1 -
 3 files changed, 4 insertions(+), 11 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/en_main.c b/drivers/net/ethernet/mellanox/mlx4/en_main.c
index 2091ae88..9f16f75 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_main.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_main.c
@@ -221,15 +221,12 @@ static void *mlx4_en_add(struct mlx4_dev *dev)
 {
 	struct mlx4_en_dev *mdev;
 	int i;
-	int err;
 
 	printk_once(KERN_INFO "%s", mlx4_en_version);
 
 	mdev = kzalloc(sizeof(*mdev), GFP_KERNEL);
-	if (!mdev) {
-		err = -ENOMEM;
+	if (!mdev)
 		goto err_free_res;
-	}
 
 	if (mlx4_pd_alloc(dev, &mdev->priv_pdn))
 		goto err_free_dev;
@@ -264,8 +261,7 @@ static void *mlx4_en_add(struct mlx4_dev *dev)
 	}
 
 	/* Build device profile according to supplied module parameters */
-	err = mlx4_en_get_profile(mdev);
-	if (err) {
+	if (mlx4_en_get_profile(mdev)) {
 		mlx4_err(mdev, "Bad module parameters, aborting\n");
 		goto err_mr;
 	}
@@ -286,10 +282,8 @@ static void *mlx4_en_add(struct mlx4_dev *dev)
 	 * Note: we cannot use the shared workqueue because of deadlocks caused
 	 *       by the rtnl lock */
 	mdev->workqueue = create_singlethread_workqueue("mlx4_en");
-	if (!mdev->workqueue) {
-		err = -ENOMEM;
+	if (!mdev->workqueue)
 		goto err_mr;
-	}
 
 	/* At this stage all non-port specific tasks are complete:
 	 * mark the card state as up */
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
index 5d60882..c4450be 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
@@ -575,7 +575,7 @@ static int mlx4_en_get_qp(struct mlx4_en_priv *priv)
 	struct mlx4_mac_entry *entry;
 	int index = 0;
 	int err = 0;
-	u64 reg_id;
+	u64 reg_id = 0;
 	int *qpn = &priv->base_qpn;
 	u64 mac = mlx4_mac_to_u64(priv->dev->dev_addr);
 
diff --git a/drivers/net/ethernet/mellanox/mlx4/en_rx.c b/drivers/net/ethernet/mellanox/mlx4/en_rx.c
index 01660c5..c8e75da 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_rx.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_rx.c
@@ -119,7 +119,6 @@ static int mlx4_en_alloc_frags(struct mlx4_en_priv *priv,
 
 out:
 	while (i--) {
-		frag_info = &priv->frag_info[i];
 		if (page_alloc[i].page != ring_alloc[i].page) {
 			dma_unmap_page(priv->ddev, page_alloc[i].dma,
 				page_alloc[i].page_size, PCI_DMA_FROMDEVICE);
-- 
1.8.3.4

[PATCH net-next 11/13] net/mlx4_en: Call napi_synchronize on stop_port

[Amir Vadai]

From: Ido Shamay <idos@mellanox.com>

This is instead of calling the actual implementation of
napi_synchronize, for better encapsulation.

Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
index c4450be..3c07a75 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
@@ -1843,8 +1843,7 @@ void mlx4_en_stop_port(struct net_device *dev, int detach)
 		}
 		local_bh_enable();
 
-		while (test_bit(NAPI_STATE_SCHED, &cq->napi.state))
-			msleep(1);
+		napi_synchronize(&cq->napi);
 		mlx4_en_deactivate_rx_ring(priv, priv->rx_ring[i]);
 		mlx4_en_deactivate_cq(priv, cq);
 
-- 
1.8.3.4

[PATCH net-next 12/13] net/mlx4_en: Move spinlocks and work initalizations to beginning of init_netdev

[Amir Vadai]

From: Eugenia Emantayev <eugenia@mellanox.com>

Upon failures, destroy_netdev is called, and spinlocks/works must be
initialized before calling it. Otherwise kernel panic may occur.


Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 30 +++++++++++++-------------
 1 file changed, 15 insertions(+), 15 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
index 3c07a75..ca6ffcf 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c
@@ -2440,6 +2440,21 @@ int mlx4_en_init_netdev(struct mlx4_en_dev *mdev, int port,
 
 	priv = netdev_priv(dev);
 	memset(priv, 0, sizeof(struct mlx4_en_priv));
+	spin_lock_init(&priv->stats_lock);
+	INIT_WORK(&priv->rx_mode_task, mlx4_en_do_set_rx_mode);
+	INIT_WORK(&priv->watchdog_task, mlx4_en_restart);
+	INIT_WORK(&priv->linkstate_task, mlx4_en_linkstate);
+	INIT_DELAYED_WORK(&priv->stats_task, mlx4_en_do_get_stats);
+	INIT_DELAYED_WORK(&priv->service_task, mlx4_en_service_task);
+#ifdef CONFIG_MLX4_EN_VXLAN
+	INIT_WORK(&priv->vxlan_add_task, mlx4_en_add_vxlan_offloads);
+	INIT_WORK(&priv->vxlan_del_task, mlx4_en_del_vxlan_offloads);
+#endif
+#ifdef CONFIG_RFS_ACCEL
+	INIT_LIST_HEAD(&priv->filters);
+	spin_lock_init(&priv->filters_lock);
+#endif
+
 	priv->dev = dev;
 	priv->mdev = mdev;
 	priv->ddev = &mdev->pdev->dev;
@@ -2471,16 +2486,6 @@ int mlx4_en_init_netdev(struct mlx4_en_dev *mdev, int port,
 	priv->cqe_size = mdev->dev->caps.cqe_size;
 	priv->mac_index = -1;
 	priv->msg_enable = MLX4_EN_MSG_LEVEL;
-	spin_lock_init(&priv->stats_lock);
-	INIT_WORK(&priv->rx_mode_task, mlx4_en_do_set_rx_mode);
-	INIT_WORK(&priv->watchdog_task, mlx4_en_restart);
-	INIT_WORK(&priv->linkstate_task, mlx4_en_linkstate);
-	INIT_DELAYED_WORK(&priv->stats_task, mlx4_en_do_get_stats);
-	INIT_DELAYED_WORK(&priv->service_task, mlx4_en_service_task);
-#ifdef CONFIG_MLX4_EN_VXLAN
-	INIT_WORK(&priv->vxlan_add_task, mlx4_en_add_vxlan_offloads);
-	INIT_WORK(&priv->vxlan_del_task, mlx4_en_del_vxlan_offloads);
-#endif
 #ifdef CONFIG_MLX4_EN_DCB
 	if (!mlx4_is_slave(priv->mdev->dev)) {
 		if (mdev->dev->caps.flags & MLX4_DEV_CAP_FLAG_SET_ETH_SCHED) {
@@ -2523,11 +2528,6 @@ int mlx4_en_init_netdev(struct mlx4_en_dev *mdev, int port,
 	if (err)
 		goto out;
 
-#ifdef CONFIG_RFS_ACCEL
-	INIT_LIST_HEAD(&priv->filters);
-	spin_lock_init(&priv->filters_lock);
-#endif
-
 	/* Initialize time stamping config */
 	priv->hwtstamp_config.flags = 0;
 	priv->hwtstamp_config.tx_type = HWTSTAMP_TX_OFF;
-- 
1.8.3.4

[PATCH net-next 13/13] net/mlx4_en: Report actual number of rings in indirection table

[Amir Vadai]

Hardware requires the number of rings in indirection table to be a power
of 2. When setting number of channels to a non power of 2 number,
indirection table is using only the closest power of 2 rings.
Report this number in 'ethtool -x' and not the total number of rx rings.


Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlx4/en_ethtool.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
index 144d6bd..8ea4d5b 100644
--- a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
+++ b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c
@@ -982,6 +982,7 @@ static int mlx4_en_get_rxfh(struct net_device *dev, u32 *ring_index, u8 *key)
 	int err = 0;
 
 	rss_rings = priv->prof->rss_rings ?: priv->rx_ring_num;
+	rss_rings = 1 << ilog2(rss_rings);
 
 	while (n--) {
 		ring_index[n] = rss_map->qps[n % rss_rings].qpn -
-- 
1.8.3.4

Re: [PATCH net-next 00/13] Mellanox ethernet driver update Oct-27-2014

[David Miller]

From: Amir Vadai <amirv@mellanox.com>
Date: Mon, 27 Oct 2014 11:37:34 +0200

> This patchset introduces some small bug fixes, support in get/set of
> vlan offload and get/set/capabilities of the link.
> 
> First 7 patches by Saeed, add support in setting/getting link speed and getting
> cable capabilities.
> Next 2 patches also by Saeed, enable the user to turn rx/tx vlan offloading on
> and off.
> Jenni fixed a bug in error flow during device initalization.
> Ido and Jack fixed some code duplication and errors discovered by static checker.
> last patch by me is a fix to make ethtool report the actual rings used by
> indirection QP.
> 
> Patches were applied and tested against commit 61ed53d ("Merge tag 'ntb-3.18'
> of git://github.com/jonmason/ntb")

Series applied to net-next, thanks.

Re: [PATCH net-next 05/13] ethtool,net/mlx4_en: Add 100M, 20G, 56G speeds ethtool reporting support

[Ben Hutchings]

[-- Attachment #1: Type: text/plain, Size: 2537 bytes --]

On Mon, 2014-10-27 at 11:37 +0200, Amir Vadai wrote:
> From: Saeed Mahameed <saeedm@mellanox.com>
> 
> Added 100M, 20G and 56G ethtool speed reporting support.
> Update mlx4_en_test_speed self test with the new speeds.
> 
> Defined new link speeds in include/uapi/linux/ethtool.h:
> +#define SPEED_20000	20000
> +#define SPEED_40000	40000
> +#define SPEED_56000	56000
> 
> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
> Signed-off-by: Amir Vadai <amirv@mellanox.com>
[...]
> --- a/include/uapi/linux/ethtool.h
> +++ b/include/uapi/linux/ethtool.h
> @@ -1213,6 +1213,10 @@ enum ethtool_sfeatures_retval_bits {
>  #define SUPPORTED_40000baseCR4_Full	(1 << 24)
>  #define SUPPORTED_40000baseSR4_Full	(1 << 25)
>  #define SUPPORTED_40000baseLR4_Full	(1 << 26)
> +#define SUPPORTED_56000baseKR4_Full	(1 << 27)
> +#define SUPPORTED_56000baseCR4_Full	(1 << 28)
> +#define SUPPORTED_56000baseSR4_Full	(1 << 29)
> +#define SUPPORTED_56000baseLR4_Full	(1 << 30)
>  
>  #define ADVERTISED_10baseT_Half		(1 << 0)
>  #define ADVERTISED_10baseT_Full		(1 << 1)
> @@ -1241,6 +1245,10 @@ enum ethtool_sfeatures_retval_bits {
>  #define ADVERTISED_40000baseCR4_Full	(1 << 24)
>  #define ADVERTISED_40000baseSR4_Full	(1 << 25)
>  #define ADVERTISED_40000baseLR4_Full	(1 << 26)
> +#define ADVERTISED_56000baseKR4_Full	(1 << 27)
> +#define ADVERTISED_56000baseCR4_Full	(1 << 28)
> +#define ADVERTISED_56000baseSR4_Full	(1 << 29)
> +#define ADVERTISED_56000baseLR4_Full	(1 << 30)

Can these modes be auto-negotiated?  If not then they don't need
advertised/supported bits.
 
>  /* The following are all involved in forcing a particular link
>   * mode for the device for setting things.  When getting the
> @@ -1248,12 +1256,16 @@ enum ethtool_sfeatures_retval_bits {
>   * it was forced up into this mode or autonegotiated.
>   */
>  
> -/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */
> +/* The forced speed, 10Mb, 100Mb, gigabit, [2.5|10|20|40|56]GbE. */
>  #define SPEED_10		10
>  #define SPEED_100		100
>  #define SPEED_1000		1000
>  #define SPEED_2500		2500
>  #define SPEED_10000		10000
> +#define SPEED_20000		20000
> +#define SPEED_40000		40000
> +#define SPEED_56000		56000

We shouldn't add new SPEED macros.  The speed is just a number of Mbit/s
and we don't need to enumerate the possible values.

Ben.

>  #define SPEED_UNKNOWN		-1
>  
>  /* Duplex, half or full. */

-- 
Ben Hutchings
The program is absolutely right; therefore, the computer must be wrong.

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 811 bytes --]

Re: [PATCH net-next 05/13] ethtool,net/mlx4_en: Add 100M, 20G, 56G speeds ethtool reporting support

[Saeed Mahameed]

On 11/6/2014 12:38 AM, Ben Hutchings wrote:
> On Mon, 2014-10-27 at 11:37 +0200, Amir Vadai wrote:
>> From: Saeed Mahameed <saeedm@mellanox.com>
>>
>> Added 100M, 20G and 56G ethtool speed reporting support.
>> Update mlx4_en_test_speed self test with the new speeds.
>>
>> Defined new link speeds in include/uapi/linux/ethtool.h:
>> +#define SPEED_20000	20000
>> +#define SPEED_40000	40000
>> +#define SPEED_56000	56000
>>
>> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
>> Signed-off-by: Amir Vadai <amirv@mellanox.com>
> [...]
>> --- a/include/uapi/linux/ethtool.h
>> +++ b/include/uapi/linux/ethtool.h
>> @@ -1213,6 +1213,10 @@ enum ethtool_sfeatures_retval_bits {
>>   #define SUPPORTED_40000baseCR4_Full	(1 << 24)
>>   #define SUPPORTED_40000baseSR4_Full	(1 << 25)
>>   #define SUPPORTED_40000baseLR4_Full	(1 << 26)
>> +#define SUPPORTED_56000baseKR4_Full	(1 << 27)
>> +#define SUPPORTED_56000baseCR4_Full	(1 << 28)
>> +#define SUPPORTED_56000baseSR4_Full	(1 << 29)
>> +#define SUPPORTED_56000baseLR4_Full	(1 << 30)
>>   
>>   #define ADVERTISED_10baseT_Half		(1 << 0)
>>   #define ADVERTISED_10baseT_Full		(1 << 1)
>> @@ -1241,6 +1245,10 @@ enum ethtool_sfeatures_retval_bits {
>>   #define ADVERTISED_40000baseCR4_Full	(1 << 24)
>>   #define ADVERTISED_40000baseSR4_Full	(1 << 25)
>>   #define ADVERTISED_40000baseLR4_Full	(1 << 26)
>> +#define ADVERTISED_56000baseKR4_Full	(1 << 27)
>> +#define ADVERTISED_56000baseCR4_Full	(1 << 28)
>> +#define ADVERTISED_56000baseSR4_Full	(1 << 29)
>> +#define ADVERTISED_56000baseLR4_Full	(1 << 30)
> Can these modes be auto-negotiated?  If not then they don't need
> advertised/supported bits.
Hi Ben,
At least 56000baseKR4_Full and 56000baseCR4_Full can be negotiated for sure,
regarding SR and LR i will check with arch team.
>>   /* The following are all involved in forcing a particular link
>>    * mode for the device for setting things.  When getting the
>> @@ -1248,12 +1256,16 @@ enum ethtool_sfeatures_retval_bits {
>>    * it was forced up into this mode or autonegotiated.
>>    */
>>   
>> -/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */
>> +/* The forced speed, 10Mb, 100Mb, gigabit, [2.5|10|20|40|56]GbE. */
>>   #define SPEED_10		10
>>   #define SPEED_100		100
>>   #define SPEED_1000		1000
>>   #define SPEED_2500		2500
>>   #define SPEED_10000		10000
>> +#define SPEED_20000		20000
>> +#define SPEED_40000		40000
>> +#define SPEED_56000		56000
> We shouldn't add new SPEED macros.  The speed is just a number of Mbit/s
> and we don't need to enumerate the possible values.
It is a little bit confusing that some speeds still use the defines 
above, and new speeds should be hardcoded.
Why those speeds still there? is it some kind of work that need to be 
done (i.e remove all of those defines) or are they needed in other 
situations.
I thought it is nice that well-known speeds are organized in such MACROs 
and this will prevent drivers from using magic numbers in their code.

Thanks for your time,
-Saeed.

>
> Ben.
>
>>   #define SPEED_UNKNOWN		-1
>>   
>>   /* Duplex, half or full. */