[PATCH net-next 0/8] ethtool: Extend module EEPROM dump API

[PATCH net-next 0/8] ethtool: Extend module EEPROM dump API

[Moshe Shemesh]

Ethtool supports module EEPROM dumps via the `ethtool -m <dev>` command.
But in current state its functionality is limited - offset and length
parameters, which are used to specify a linear desired region of EEPROM
data to dump, is not enough, considering emergence of complex module
EEPROM layouts such as CMIS 4.0.
Moreover, CMIS 4.0 extends the amount of pages that may be accessible by
introducing another parameter for page addressing - banks.

Besides, currently module EEPROM is represented as a chunk of
concatenated pages, where lower 128 bytes of all pages, except page 00h,
are omitted. Offset and length are used to address parts of this fake
linear memory. But in practice drivers, which implement
get_module_info() and get_module_eeprom() ethtool ops still calculate
page number and set I2C address on their own.

This series tackles these issues by adding ethtool op, which allows to
pass page number, bank number and I2C address in addition to offset and
length parameters to the driver, adds corresponding netlink
infrastructure and implements the new interface in mlx5 driver.

This allows to extend userspace 'ethtool -m' CLI by adding new
parameters - page, bank and i2c. New command line format:
 ethtool -m <dev> [hex on|off] [raw on|off] [offset N] [length N] [page N] [bank N] [i2c N]

The consequence of this series is a possibility to dump arbitrary EEPROM
page at a time, in contrast to dumps of concatenated pages. Therefore,
offset and length change their semantics and may be used only to specify
a part of data within half page boundary, which size is currently limited
to 128 bytes.

As for drivers that support legacy get_module_info() and
get_module_eeprom() pair, the series addresses it by implementing a
fallback mechanism. As mentioned earlier, such drivers derive a page
number from 'global' offset, so this can be done vice versa without
their involvement thanks to standardization. If kernel netlink handler
of 'ethtool -m' command detects that new ethtool op is not supported by
the driver, it calculates offset from given page number and page offset
and calls old ndos, if they are available.

Change log:
RFC v5 -> v1:
- Added support for generic SFP (by Andrew).
- Fixd fallback code by exporting functions ethtool_get_module_eeprom_call()
  and ethtool_get_module_info_call() (by Andrew).
- Fix ETH_MODULE_EEPROM_PAGE_LEN in fallback to
  ETH_MODULE_EEPROM_PAGE_LEN * 2 when accounting for high I2C.

RFC v4 -> RFC v5:
- Limited KAPI to only read 1/2 page at once.
- Redefined ETH_MODULE_EEPROM_PAGE_LEN as 128.
- Made page number mandatory for any request.
- Added extack messages for invalid parameters failures.

RFC v3 -> RFC v4:
- Renamed many identifiers to use 'eeprom' instead of 'eeprom_data'.
- Renamed netlink enums and defines to use 'MODULE_EEPROM' instead of
   'EEPROM_DATA'.
- Renamed struct ethtool_eeprom_data to ethtool_module_eeprom.
- Added MODULE_EEPROM_MAX_OFFSET (257 * 256) macro and check global offset
    against it to avoid overflow.
- Removed ndo pointer check from _parse_request().
- Removed separate length element from netlink response.
- Limited reads to 128 bytes without crossing half page bound.

RFC v2 -> RFC v3:
- Removed page number limitations
- Added length limit when page is present in fallback
- Changed page, bank and i2c_address type to u8 all over the patchset
- Added 0x51 I2C address usage increasing offset by 256 for SFP

RFC v1 -> RFC v2:
- Limited i2c_address values by 127
- Added page bound check for offset and length
- Added defines for these two points
- Added extack to ndo parameters
- Moved ethnl_ops_begin(dev) and set error path accordingly


Andrew Lunn (3):
  net: ethtool: Export helpers for getting EEPROM info
  phy: sfp: add netlink SFP support to generic SFP code
  ethtool: wire in generic SFP module access

Vladyslav Tarasiuk (5):
  ethtool: Allow network drivers to dump arbitrary EEPROM data
  net/mlx5: Refactor module EEPROM query
  net/mlx5: Implement get_module_eeprom_by_page()
  net/mlx5: Add support for DSFP module EEPROM dumps
  ethtool: Add fallback to get_module_eeprom from netlink command

 Documentation/networking/ethtool-netlink.rst  |  36 ++-
 .../ethernet/mellanox/mlx5/core/en_ethtool.c  |  44 ++++
 .../net/ethernet/mellanox/mlx5/core/port.c    | 110 ++++++--
 drivers/net/phy/sfp-bus.c                     |  20 ++
 drivers/net/phy/sfp.c                         |  25 ++
 drivers/net/phy/sfp.h                         |   3 +
 include/linux/ethtool.h                       |  33 ++-
 include/linux/mlx5/port.h                     |  12 +
 include/linux/sfp.h                           |  10 +
 include/uapi/linux/ethtool_netlink.h          |  19 ++
 net/ethtool/Makefile                          |   2 +-
 net/ethtool/common.h                          |   5 +
 net/ethtool/eeprom.c                          | 246 ++++++++++++++++++
 net/ethtool/ioctl.c                           |  14 +-
 net/ethtool/netlink.c                         |  11 +
 net/ethtool/netlink.h                         |   2 +
 16 files changed, 553 insertions(+), 39 deletions(-)
 create mode 100644 net/ethtool/eeprom.c

-- 
2.26.2

[PATCH net-next 1/8] ethtool: Allow network drivers to dump arbitrary EEPROM data

[Moshe Shemesh]

From: Vladyslav Tarasiuk <vladyslavt@nvidia.com>

Define get_module_eeprom_by_page() ethtool callback and implement
netlink infrastructure.

get_module_eeprom_by_page() allows network drivers to dump a part of
module's EEPROM specified by page and bank numbers along with offset and
length. It is effectively a netlink replacement for get_module_info()
and get_module_eeprom() pair, which is needed due to emergence of
complex non-linear EEPROM layouts.

Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
---
 Documentation/networking/ethtool-netlink.rst |  36 +++-
 include/linux/ethtool.h                      |  33 +++-
 include/uapi/linux/ethtool_netlink.h         |  19 +++
 net/ethtool/Makefile                         |   2 +-
 net/ethtool/eeprom.c                         | 171 +++++++++++++++++++
 net/ethtool/netlink.c                        |  11 ++
 net/ethtool/netlink.h                        |   2 +
 7 files changed, 270 insertions(+), 4 deletions(-)
 create mode 100644 net/ethtool/eeprom.c

diff --git a/Documentation/networking/ethtool-netlink.rst b/Documentation/networking/ethtool-netlink.rst
index fd84f4ed898a..77e4a838f247 100644
--- a/Documentation/networking/ethtool-netlink.rst
+++ b/Documentation/networking/ethtool-netlink.rst
@@ -1338,6 +1338,38 @@ in an implementation specific way.
 ``ETHTOOL_A_FEC_AUTO`` requests the driver to choose FEC mode based on SFP
 module parameters. This does not mean autonegotiation.
 
+MODULE_EEPROM
+=============
+
+Fetch module EEPROM data dump.
+This interface is designed to allow dumps of at most 1/2 page at once. This
+means only dumps of 128 (or less) bytes are allowed, without crossing half page
+boundary located at offset 128. For pages other than 0 only high 128 bytes are
+accessible.
+
+Request contents:
+
+  =======================================  ======  ==========================
+  ``ETHTOOL_A_MODULE_EEPROM_HEADER``       nested  request header
+  ``ETHTOOL_A_MODULE_EEPROM_OFFSET``       u32     offset within a page
+  ``ETHTOOL_A_MODULE_EEPROM_LENGTH``       u32     amount of bytes to read
+  ``ETHTOOL_A_MODULE_EEPROM_PAGE``         u8      page number
+  ``ETHTOOL_A_MODULE_EEPROM_BANK``         u8      bank number
+  ``ETHTOOL_A_MODULE_EEPROM_I2C_ADDRESS``  u8      page I2C address
+  =======================================  ======  ==========================
+
+Kernel response contents:
+
+ +---------------------------------------------+--------+---------------------+
+ | ``ETHTOOL_A_MODULE_EEPROM_HEADER``          | nested | reply header        |
+ +---------------------------------------------+--------+---------------------+
+ | ``ETHTOOL_A_MODULE_EEPROM_DATA``            | nested | array of bytes from |
+ |                                             |        | module EEPROM       |
+ +---------------------------------------------+--------+---------------------+
+
+``ETHTOOL_A_MODULE_EEPROM_DATA`` has an attribute length equal to the amount of
+bytes driver actually read.
+
 Request translation
 ===================
 
@@ -1415,8 +1447,8 @@ are netlink only.
   ``ETHTOOL_GET_DUMP_FLAG``           n/a
   ``ETHTOOL_GET_DUMP_DATA``           n/a
   ``ETHTOOL_GET_TS_INFO``             ``ETHTOOL_MSG_TSINFO_GET``
-  ``ETHTOOL_GMODULEINFO``             n/a
-  ``ETHTOOL_GMODULEEEPROM``           n/a
+  ``ETHTOOL_GMODULEINFO``             ``ETHTOOL_MSG_MODULE_EEPROM_GET``
+  ``ETHTOOL_GMODULEEEPROM``           ``ETHTOOL_MSG_MODULE_EEPROM_GET``
   ``ETHTOOL_GEEE``                    ``ETHTOOL_MSG_EEE_GET``
   ``ETHTOOL_SEEE``                    ``ETHTOOL_MSG_EEE_SET``
   ``ETHTOOL_GRSSH``                   n/a
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index 5c631a298994..7106c73fca34 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -81,6 +81,7 @@ enum {
 #define ETH_RSS_HASH_NO_CHANGE	0
 
 struct net_device;
+struct netlink_ext_ack;
 
 /* Some generic methods drivers may use in their ethtool_ops */
 u32 ethtool_op_get_link(struct net_device *dev);
@@ -265,6 +266,31 @@ struct ethtool_pause_stats {
 	u64 rx_pause_frames;
 };
 
+#define ETH_MODULE_EEPROM_PAGE_LEN	128
+#define ETH_MODULE_MAX_I2C_ADDRESS	0x7f
+
+/**
+ * struct ethtool_module_eeprom - EEPROM dump from specified page
+ * @offset: Offset within the specified EEPROM page to begin read, in bytes.
+ * @length: Number of bytes to read.
+ * @page: Page number to read from.
+ * @bank: Page bank number to read from, if applicable by EEPROM spec.
+ * @i2c_address: I2C address of a page. Value less than 0x7f expected. Most
+ *	EEPROMs use 0x50 or 0x51.
+ * @data: Pointer to buffer with EEPROM data of @length size.
+ *
+ * This can be used to manage pages during EEPROM dump in ethtool and pass
+ * required information to the driver.
+ */
+struct ethtool_module_eeprom {
+	__u32	offset;
+	__u32	length;
+	__u8	page;
+	__u8	bank;
+	__u8	i2c_address;
+	__u8	*data;
+};
+
 /**
  * struct ethtool_ops - optional netdev operations
  * @cap_link_lanes_supported: indicates if the driver supports lanes
@@ -412,6 +438,9 @@ struct ethtool_pause_stats {
  *	cannot use the standard PHY library helpers.
  * @get_phy_tunable: Read the value of a PHY tunable.
  * @set_phy_tunable: Set the value of a PHY tunable.
+ * @get_module_eeprom_by_page: Get a region of plug-in module EEPROM data from
+ *	specified page. Returns a negative error code or the amount of bytes
+ *	read.
  *
  * All operations are optional (i.e. the function pointer may be set
  * to %NULL) and callers must take this into account.  Callers must
@@ -517,6 +546,9 @@ struct ethtool_ops {
 				   const struct ethtool_tunable *, void *);
 	int	(*set_phy_tunable)(struct net_device *,
 				   const struct ethtool_tunable *, const void *);
+	int	(*get_module_eeprom_by_page)(struct net_device *dev,
+					     const struct ethtool_module_eeprom *page,
+					     struct netlink_ext_ack *extack);
 };
 
 int ethtool_check_ops(const struct ethtool_ops *ops);
@@ -540,7 +572,6 @@ int ethtool_virtdev_set_link_ksettings(struct net_device *dev,
 				       const struct ethtool_link_ksettings *cmd,
 				       u32 *dev_speed, u8 *dev_duplex);
 
-struct netlink_ext_ack;
 struct phy_device;
 struct phy_tdr_config;
 
diff --git a/include/uapi/linux/ethtool_netlink.h b/include/uapi/linux/ethtool_netlink.h
index 7f1bdb5b31ba..9612dcd48a6a 100644
--- a/include/uapi/linux/ethtool_netlink.h
+++ b/include/uapi/linux/ethtool_netlink.h
@@ -44,6 +44,7 @@ enum {
 	ETHTOOL_MSG_TUNNEL_INFO_GET,
 	ETHTOOL_MSG_FEC_GET,
 	ETHTOOL_MSG_FEC_SET,
+	ETHTOOL_MSG_MODULE_EEPROM_GET,
 
 	/* add new constants above here */
 	__ETHTOOL_MSG_USER_CNT,
@@ -84,6 +85,7 @@ enum {
 	ETHTOOL_MSG_TUNNEL_INFO_GET_REPLY,
 	ETHTOOL_MSG_FEC_GET_REPLY,
 	ETHTOOL_MSG_FEC_NTF,
+	ETHTOOL_MSG_MODULE_EEPROM_GET_REPLY,
 
 	/* add new constants above here */
 	__ETHTOOL_MSG_KERNEL_CNT,
@@ -646,6 +648,23 @@ enum {
 	ETHTOOL_A_FEC_MAX = (__ETHTOOL_A_FEC_CNT - 1)
 };
 
+/* MODULE EEPROM */
+
+enum {
+	ETHTOOL_A_MODULE_EEPROM_UNSPEC,
+	ETHTOOL_A_MODULE_EEPROM_HEADER,			/* nest - _A_HEADER_* */
+
+	ETHTOOL_A_MODULE_EEPROM_OFFSET,			/* u32 */
+	ETHTOOL_A_MODULE_EEPROM_LENGTH,			/* u32 */
+	ETHTOOL_A_MODULE_EEPROM_PAGE,			/* u8 */
+	ETHTOOL_A_MODULE_EEPROM_BANK,			/* u8 */
+	ETHTOOL_A_MODULE_EEPROM_I2C_ADDRESS,		/* u8 */
+	ETHTOOL_A_MODULE_EEPROM_DATA,			/* nested */
+
+	__ETHTOOL_A_MODULE_EEPROM_CNT,
+	ETHTOOL_A_MODULE_EEPROM_MAX = (__ETHTOOL_A_MODULE_EEPROM_CNT - 1)
+};
+
 /* generic netlink info */
 #define ETHTOOL_GENL_NAME "ethtool"
 #define ETHTOOL_GENL_VERSION 1
diff --git a/net/ethtool/Makefile b/net/ethtool/Makefile
index c2dc9033a8f7..83842685fd8c 100644
--- a/net/ethtool/Makefile
+++ b/net/ethtool/Makefile
@@ -7,4 +7,4 @@ obj-$(CONFIG_ETHTOOL_NETLINK)	+= ethtool_nl.o
 ethtool_nl-y	:= netlink.o bitset.o strset.o linkinfo.o linkmodes.o \
 		   linkstate.o debug.o wol.o features.o privflags.o rings.o \
 		   channels.o coalesce.o pause.o eee.o tsinfo.o cabletest.o \
-		   tunnels.o fec.o
+		   tunnels.o fec.o eeprom.o
diff --git a/net/ethtool/eeprom.c b/net/ethtool/eeprom.c
new file mode 100644
index 000000000000..8536dd905da5
--- /dev/null
+++ b/net/ethtool/eeprom.c
@@ -0,0 +1,171 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/ethtool.h>
+#include "netlink.h"
+#include "common.h"
+
+struct eeprom_req_info {
+	struct ethnl_req_info	base;
+	u32			offset;
+	u32			length;
+	u8			page;
+	u8			bank;
+	u8			i2c_address;
+};
+
+struct eeprom_reply_data {
+	struct ethnl_reply_data base;
+	u32			length;
+	u8			*data;
+};
+
+#define MODULE_EEPROM_REQINFO(__req_base) \
+	container_of(__req_base, struct eeprom_req_info, base)
+
+#define MODULE_EEPROM_REPDATA(__reply_base) \
+	container_of(__reply_base, struct eeprom_reply_data, base)
+
+static int eeprom_prepare_data(const struct ethnl_req_info *req_base,
+			       struct ethnl_reply_data *reply_base,
+			       struct genl_info *info)
+{
+	struct eeprom_reply_data *reply = MODULE_EEPROM_REPDATA(reply_base);
+	struct eeprom_req_info *request = MODULE_EEPROM_REQINFO(req_base);
+	struct ethtool_module_eeprom page_data = {0};
+	struct net_device *dev = reply_base->dev;
+	int ret;
+
+	if (!dev->ethtool_ops->get_module_eeprom_by_page)
+		return -EOPNOTSUPP;
+
+	page_data.offset = request->offset;
+	page_data.length = request->length;
+	page_data.i2c_address = request->i2c_address;
+	page_data.page = request->page;
+	page_data.bank = request->bank;
+	page_data.data = kmalloc(page_data.length, GFP_KERNEL);
+	if (!page_data.data)
+		return -ENOMEM;
+
+	ret = ethnl_ops_begin(dev);
+	if (ret)
+		goto err_free;
+
+	ret = dev->ethtool_ops->get_module_eeprom_by_page(dev, &page_data,
+							  info->extack);
+	if (ret < 0)
+		goto err_ops;
+
+	reply->length = ret;
+	reply->data = page_data.data;
+
+	ethnl_ops_complete(dev);
+	return 0;
+
+err_ops:
+	ethnl_ops_complete(dev);
+err_free:
+	kfree(page_data.data);
+	return ret;
+}
+
+static int eeprom_parse_request(struct ethnl_req_info *req_info, struct nlattr **tb,
+				struct netlink_ext_ack *extack)
+{
+	struct eeprom_req_info *request = MODULE_EEPROM_REQINFO(req_info);
+
+	if (!tb[ETHTOOL_A_MODULE_EEPROM_OFFSET] ||
+	    !tb[ETHTOOL_A_MODULE_EEPROM_LENGTH] ||
+	    !tb[ETHTOOL_A_MODULE_EEPROM_PAGE] ||
+	    !tb[ETHTOOL_A_MODULE_EEPROM_I2C_ADDRESS])
+		return -EINVAL;
+
+	request->i2c_address = nla_get_u8(tb[ETHTOOL_A_MODULE_EEPROM_I2C_ADDRESS]);
+	request->offset = nla_get_u32(tb[ETHTOOL_A_MODULE_EEPROM_OFFSET]);
+	request->length = nla_get_u32(tb[ETHTOOL_A_MODULE_EEPROM_LENGTH]);
+
+	if (!request->length)
+		return -EINVAL;
+
+	/* The following set of conditions limit the API to only dump 1/2
+	 * EEPROM page without crossing low page boundary located at offset 128.
+	 * This means user may only request dumps of length limited to 128 from
+	 * either low 128 bytes or high 128 bytes.
+	 * For pages higher than 0 only high 128 bytes are accessible.
+	 */
+	request->page = nla_get_u8(tb[ETHTOOL_A_MODULE_EEPROM_PAGE]);
+	if (request->page && request->offset < ETH_MODULE_EEPROM_PAGE_LEN) {
+		NL_SET_ERR_MSG_ATTR(extack, tb[ETHTOOL_A_MODULE_EEPROM_PAGE],
+				    "reading from lower half page is allowed for page 0 only");
+		return -EINVAL;
+	}
+
+	if (request->offset < ETH_MODULE_EEPROM_PAGE_LEN &&
+	    request->offset + request->length > ETH_MODULE_EEPROM_PAGE_LEN) {
+		NL_SET_ERR_MSG_ATTR(extack, tb[ETHTOOL_A_MODULE_EEPROM_LENGTH],
+				    "reading cross half page boundary is illegal");
+		return -EINVAL;
+	} else if (request->offset >= ETH_MODULE_EEPROM_PAGE_LEN * 2) {
+		NL_SET_ERR_MSG_ATTR(extack, tb[ETHTOOL_A_MODULE_EEPROM_OFFSET],
+				    "offset is out of bounds");
+		return -EINVAL;
+	} else if (request->offset + request->length > ETH_MODULE_EEPROM_PAGE_LEN * 2) {
+		NL_SET_ERR_MSG_ATTR(extack, tb[ETHTOOL_A_MODULE_EEPROM_LENGTH],
+				    "reading cross page boundary is illegal");
+		return -EINVAL;
+	}
+
+	if (tb[ETHTOOL_A_MODULE_EEPROM_BANK])
+		request->bank = nla_get_u8(tb[ETHTOOL_A_MODULE_EEPROM_BANK]);
+
+	return 0;
+}
+
+static int eeprom_reply_size(const struct ethnl_req_info *req_base,
+			     const struct ethnl_reply_data *reply_base)
+{
+	const struct eeprom_req_info *request = MODULE_EEPROM_REQINFO(req_base);
+
+	return nla_total_size(sizeof(u8) * request->length); /* _EEPROM_DATA */
+}
+
+static int eeprom_fill_reply(struct sk_buff *skb,
+			     const struct ethnl_req_info *req_base,
+			     const struct ethnl_reply_data *reply_base)
+{
+	struct eeprom_reply_data *reply = MODULE_EEPROM_REPDATA(reply_base);
+
+	return nla_put(skb, ETHTOOL_A_MODULE_EEPROM_DATA, reply->length, reply->data);
+}
+
+static void eeprom_cleanup_data(struct ethnl_reply_data *reply_base)
+{
+	struct eeprom_reply_data *reply = MODULE_EEPROM_REPDATA(reply_base);
+
+	kfree(reply->data);
+}
+
+const struct ethnl_request_ops ethnl_module_eeprom_request_ops = {
+	.request_cmd		= ETHTOOL_MSG_MODULE_EEPROM_GET,
+	.reply_cmd		= ETHTOOL_MSG_MODULE_EEPROM_GET_REPLY,
+	.hdr_attr		= ETHTOOL_A_MODULE_EEPROM_HEADER,
+	.req_info_size		= sizeof(struct eeprom_req_info),
+	.reply_data_size	= sizeof(struct eeprom_reply_data),
+
+	.parse_request		= eeprom_parse_request,
+	.prepare_data		= eeprom_prepare_data,
+	.reply_size		= eeprom_reply_size,
+	.fill_reply		= eeprom_fill_reply,
+	.cleanup_data		= eeprom_cleanup_data,
+};
+
+const struct nla_policy ethnl_module_eeprom_get_policy[] = {
+	[ETHTOOL_A_MODULE_EEPROM_HEADER]	= NLA_POLICY_NESTED(ethnl_header_policy),
+	[ETHTOOL_A_MODULE_EEPROM_OFFSET]	= { .type = NLA_U32 },
+	[ETHTOOL_A_MODULE_EEPROM_LENGTH]	= { .type = NLA_U32 },
+	[ETHTOOL_A_MODULE_EEPROM_PAGE]		= { .type = NLA_U8 },
+	[ETHTOOL_A_MODULE_EEPROM_BANK]		= { .type = NLA_U8 },
+	[ETHTOOL_A_MODULE_EEPROM_I2C_ADDRESS]	=
+		NLA_POLICY_RANGE(NLA_U8, 0, ETH_MODULE_MAX_I2C_ADDRESS),
+};
+
diff --git a/net/ethtool/netlink.c b/net/ethtool/netlink.c
index 705a4b201564..5f5d7c4b3d4a 100644
--- a/net/ethtool/netlink.c
+++ b/net/ethtool/netlink.c
@@ -246,6 +246,7 @@ ethnl_default_requests[__ETHTOOL_MSG_USER_CNT] = {
 	[ETHTOOL_MSG_EEE_GET]		= &ethnl_eee_request_ops,
 	[ETHTOOL_MSG_FEC_GET]		= &ethnl_fec_request_ops,
 	[ETHTOOL_MSG_TSINFO_GET]	= &ethnl_tsinfo_request_ops,
+	[ETHTOOL_MSG_MODULE_EEPROM_GET]	= &ethnl_module_eeprom_request_ops,
 };
 
 static struct ethnl_dump_ctx *ethnl_dump_context(struct netlink_callback *cb)
@@ -931,6 +932,16 @@ static const struct genl_ops ethtool_genl_ops[] = {
 		.policy = ethnl_fec_set_policy,
 		.maxattr = ARRAY_SIZE(ethnl_fec_set_policy) - 1,
 	},
+	{
+		.cmd	= ETHTOOL_MSG_MODULE_EEPROM_GET,
+		.flags  = GENL_UNS_ADMIN_PERM,
+		.doit	= ethnl_default_doit,
+		.start	= ethnl_default_start,
+		.dumpit	= ethnl_default_dumpit,
+		.done	= ethnl_default_done,
+		.policy = ethnl_module_eeprom_get_policy,
+		.maxattr = ARRAY_SIZE(ethnl_module_eeprom_get_policy) - 1,
+	},
 };
 
 static const struct genl_multicast_group ethtool_nl_mcgrps[] = {
diff --git a/net/ethtool/netlink.h b/net/ethtool/netlink.h
index 785f7ee45930..4305ac971bb0 100644
--- a/net/ethtool/netlink.h
+++ b/net/ethtool/netlink.h
@@ -345,6 +345,7 @@ extern const struct ethnl_request_ops ethnl_pause_request_ops;
 extern const struct ethnl_request_ops ethnl_eee_request_ops;
 extern const struct ethnl_request_ops ethnl_tsinfo_request_ops;
 extern const struct ethnl_request_ops ethnl_fec_request_ops;
+extern const struct ethnl_request_ops ethnl_module_eeprom_request_ops;
 
 extern const struct nla_policy ethnl_header_policy[ETHTOOL_A_HEADER_FLAGS + 1];
 extern const struct nla_policy ethnl_header_policy_stats[ETHTOOL_A_HEADER_FLAGS + 1];
@@ -378,6 +379,7 @@ extern const struct nla_policy ethnl_cable_test_tdr_act_policy[ETHTOOL_A_CABLE_T
 extern const struct nla_policy ethnl_tunnel_info_get_policy[ETHTOOL_A_TUNNEL_INFO_HEADER + 1];
 extern const struct nla_policy ethnl_fec_get_policy[ETHTOOL_A_FEC_HEADER + 1];
 extern const struct nla_policy ethnl_fec_set_policy[ETHTOOL_A_FEC_AUTO + 1];
+extern const struct nla_policy ethnl_module_eeprom_get_policy[ETHTOOL_A_MODULE_EEPROM_DATA + 1];
 
 int ethnl_set_linkinfo(struct sk_buff *skb, struct genl_info *info);
 int ethnl_set_linkmodes(struct sk_buff *skb, struct genl_info *info);
-- 
2.26.2

[PATCH net-next 2/8] net/mlx5: Refactor module EEPROM query

[Moshe Shemesh]

From: Vladyslav Tarasiuk <vladyslavt@nvidia.com>

Prepare for ethtool_ops::get_module_eeprom_data() implementation by
extracting common part of mlx5_query_module_eeprom() into a separate
function.

Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
---
 .../net/ethernet/mellanox/mlx5/core/port.c    | 79 +++++++++++--------
 include/linux/mlx5/port.h                     |  9 +++
 2 files changed, 54 insertions(+), 34 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlx5/core/port.c b/drivers/net/ethernet/mellanox/mlx5/core/port.c
index 4bb219565c58..9b9f870d67a4 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/port.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/port.c
@@ -353,67 +353,78 @@ static void mlx5_sfp_eeprom_params_set(u16 *i2c_addr, int *page_num, u16 *offset
 	*offset -= MLX5_EEPROM_PAGE_LENGTH;
 }
 
-int mlx5_query_module_eeprom(struct mlx5_core_dev *dev,
-			     u16 offset, u16 size, u8 *data)
+static int mlx5_query_mcia(struct mlx5_core_dev *dev,
+			   struct mlx5_module_eeprom_query_params *params, u8 *data)
 {
-	int module_num, status, err, page_num = 0;
 	u32 in[MLX5_ST_SZ_DW(mcia_reg)] = {};
 	u32 out[MLX5_ST_SZ_DW(mcia_reg)];
-	u16 i2c_addr = 0;
-	u8 module_id;
+	int status, err;
 	void *ptr;
+	u16 size;
+
+	size = min_t(int, params->size, MLX5_EEPROM_MAX_BYTES);
+
+	MLX5_SET(mcia_reg, in, l, 0);
+	MLX5_SET(mcia_reg, in, size, size);
+	MLX5_SET(mcia_reg, in, module, params->module_number);
+	MLX5_SET(mcia_reg, in, device_address, params->offset);
+	MLX5_SET(mcia_reg, in, page_number, params->page);
+	MLX5_SET(mcia_reg, in, i2c_device_address, params->i2c_address);
 
-	err = mlx5_query_module_num(dev, &module_num);
+	err = mlx5_core_access_reg(dev, in, sizeof(in), out,
+				   sizeof(out), MLX5_REG_MCIA, 0, 0);
 	if (err)
 		return err;
 
-	err = mlx5_query_module_id(dev, module_num, &module_id);
+	status = MLX5_GET(mcia_reg, out, status);
+	if (status) {
+		mlx5_core_err(dev, "query_mcia_reg failed: status: 0x%x\n",
+			      status);
+		return -EIO;
+	}
+
+	ptr = MLX5_ADDR_OF(mcia_reg, out, dword_0);
+	memcpy(data, ptr, size);
+
+	return size;
+}
+
+int mlx5_query_module_eeprom(struct mlx5_core_dev *dev,
+			     u16 offset, u16 size, u8 *data)
+{
+	struct mlx5_module_eeprom_query_params query = {0};
+	u8 module_id;
+	int err;
+
+	err = mlx5_query_module_num(dev, &query.module_number);
+	if (err)
+		return err;
+
+	err = mlx5_query_module_id(dev, query.module_number, &module_id);
 	if (err)
 		return err;
 
 	switch (module_id) {
 	case MLX5_MODULE_ID_SFP:
-		mlx5_sfp_eeprom_params_set(&i2c_addr, &page_num, &offset);
+		mlx5_sfp_eeprom_params_set(&query.i2c_address, &query.page, &query.offset);
 		break;
 	case MLX5_MODULE_ID_QSFP:
 	case MLX5_MODULE_ID_QSFP_PLUS:
 	case MLX5_MODULE_ID_QSFP28:
-		mlx5_qsfp_eeprom_params_set(&i2c_addr, &page_num, &offset);
+		mlx5_qsfp_eeprom_params_set(&query.i2c_address, &query.page, &query.offset);
 		break;
 	default:
 		mlx5_core_err(dev, "Module ID not recognized: 0x%x\n", module_id);
 		return -EINVAL;
 	}
 
-	if (offset + size > MLX5_EEPROM_PAGE_LENGTH)
+	if (query.offset + size > MLX5_EEPROM_PAGE_LENGTH)
 		/* Cross pages read, read until offset 256 in low page */
 		size -= offset + size - MLX5_EEPROM_PAGE_LENGTH;
 
-	size = min_t(int, size, MLX5_EEPROM_MAX_BYTES);
+	query.size = size;
 
-	MLX5_SET(mcia_reg, in, l, 0);
-	MLX5_SET(mcia_reg, in, module, module_num);
-	MLX5_SET(mcia_reg, in, i2c_device_address, i2c_addr);
-	MLX5_SET(mcia_reg, in, page_number, page_num);
-	MLX5_SET(mcia_reg, in, device_address, offset);
-	MLX5_SET(mcia_reg, in, size, size);
-
-	err = mlx5_core_access_reg(dev, in, sizeof(in), out,
-				   sizeof(out), MLX5_REG_MCIA, 0, 0);
-	if (err)
-		return err;
-
-	status = MLX5_GET(mcia_reg, out, status);
-	if (status) {
-		mlx5_core_err(dev, "query_mcia_reg failed: status: 0x%x\n",
-			      status);
-		return -EIO;
-	}
-
-	ptr = MLX5_ADDR_OF(mcia_reg, out, dword_0);
-	memcpy(data, ptr, size);
-
-	return size;
+	return mlx5_query_mcia(dev, &query, data);
 }
 EXPORT_SYMBOL_GPL(mlx5_query_module_eeprom);
 
diff --git a/include/linux/mlx5/port.h b/include/linux/mlx5/port.h
index 23edd2db4803..90b87aa82db3 100644
--- a/include/linux/mlx5/port.h
+++ b/include/linux/mlx5/port.h
@@ -62,6 +62,15 @@ enum mlx5_an_status {
 #define MLX5_EEPROM_PAGE_LENGTH		256
 #define MLX5_EEPROM_HIGH_PAGE_LENGTH	128
 
+struct mlx5_module_eeprom_query_params {
+	u16 size;
+	u16 offset;
+	u16 i2c_address;
+	u32 page;
+	u32 bank;
+	u32 module_number;
+};
+
 enum mlx5e_link_mode {
 	MLX5E_1000BASE_CX_SGMII	 = 0,
 	MLX5E_1000BASE_KX	 = 1,
-- 
2.26.2

[PATCH net-next 3/8] net/mlx5: Implement get_module_eeprom_by_page()

[Moshe Shemesh]

From: Vladyslav Tarasiuk <vladyslavt@nvidia.com>

Implement ethtool_ops::get_module_eeprom_by_page() to enable
support of new SFP standards.

Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
---
 .../ethernet/mellanox/mlx5/core/en_ethtool.c  | 44 +++++++++++++++++++
 .../net/ethernet/mellanox/mlx5/core/port.c    | 41 +++++++++++++++++
 include/linux/mlx5/port.h                     |  2 +
 3 files changed, 87 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c b/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
index 964558086ad6..c238804b0664 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
@@ -1770,6 +1770,49 @@ static int mlx5e_get_module_eeprom(struct net_device *netdev,
 	return 0;
 }
 
+static int mlx5e_get_module_eeprom_by_page(struct net_device *netdev,
+					   const struct ethtool_module_eeprom *page_data,
+					   struct netlink_ext_ack *extack)
+{
+	struct mlx5e_priv *priv = netdev_priv(netdev);
+	struct mlx5_module_eeprom_query_params query;
+	struct mlx5_core_dev *mdev = priv->mdev;
+	u8 *data = page_data->data;
+	int size_read;
+	int i = 0;
+
+	if (!page_data->length)
+		return -EINVAL;
+
+	memset(data, 0, page_data->length);
+
+	query.offset = page_data->offset;
+	query.i2c_address = page_data->i2c_address;
+	query.bank = page_data->bank;
+	query.page = page_data->page;
+	while (i < page_data->length) {
+		query.size = page_data->length - i;
+		size_read = mlx5_query_module_eeprom_by_page(mdev, &query, data + i);
+
+		/* Done reading, return how many bytes was read */
+		if (!size_read)
+			return i;
+
+		if (size_read == -EINVAL)
+			return -EINVAL;
+		if (size_read < 0) {
+			netdev_err(priv->netdev, "%s: mlx5_query_module_eeprom_by_page failed:0x%x\n",
+				   __func__, size_read);
+			return i;
+		}
+
+		i += size_read;
+		query.offset += size_read;
+	}
+
+	return i;
+}
+
 int mlx5e_ethtool_flash_device(struct mlx5e_priv *priv,
 			       struct ethtool_flash *flash)
 {
@@ -2159,6 +2202,7 @@ const struct ethtool_ops mlx5e_ethtool_ops = {
 	.set_wol	   = mlx5e_set_wol,
 	.get_module_info   = mlx5e_get_module_info,
 	.get_module_eeprom = mlx5e_get_module_eeprom,
+	.get_module_eeprom_by_page = mlx5e_get_module_eeprom_by_page,
 	.flash_device      = mlx5e_flash_device,
 	.get_priv_flags    = mlx5e_get_priv_flags,
 	.set_priv_flags    = mlx5e_set_priv_flags,
diff --git a/drivers/net/ethernet/mellanox/mlx5/core/port.c b/drivers/net/ethernet/mellanox/mlx5/core/port.c
index 9b9f870d67a4..522a41f8f1e2 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/port.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/port.c
@@ -428,6 +428,47 @@ int mlx5_query_module_eeprom(struct mlx5_core_dev *dev,
 }
 EXPORT_SYMBOL_GPL(mlx5_query_module_eeprom);
 
+int mlx5_query_module_eeprom_by_page(struct mlx5_core_dev *dev,
+				     struct mlx5_module_eeprom_query_params *params,
+				     u8 *data)
+{
+	u8 module_id;
+	int err;
+
+	err = mlx5_query_module_num(dev, &params->module_number);
+	if (err)
+		return err;
+
+	err = mlx5_query_module_id(dev, params->module_number, &module_id);
+	if (err)
+		return err;
+
+	switch (module_id) {
+	case MLX5_MODULE_ID_SFP:
+		if (params->page > 0)
+			return -EINVAL;
+		break;
+	case MLX5_MODULE_ID_QSFP:
+	case MLX5_MODULE_ID_QSFP28:
+	case MLX5_MODULE_ID_QSFP_PLUS:
+		if (params->page > 3)
+			return -EINVAL;
+		break;
+	default:
+		mlx5_core_err(dev, "Module ID not recognized: 0x%x\n", module_id);
+		return -EINVAL;
+	}
+
+	if (params->i2c_address != MLX5_I2C_ADDR_HIGH &&
+	    params->i2c_address != MLX5_I2C_ADDR_LOW) {
+		mlx5_core_err(dev, "I2C address not recognized: 0x%x\n", params->i2c_address);
+		return -EINVAL;
+	}
+
+	return mlx5_query_mcia(dev, params, data);
+}
+EXPORT_SYMBOL_GPL(mlx5_query_module_eeprom_by_page);
+
 static int mlx5_query_port_pvlc(struct mlx5_core_dev *dev, u32 *pvlc,
 				int pvlc_size,  u8 local_port)
 {
diff --git a/include/linux/mlx5/port.h b/include/linux/mlx5/port.h
index 90b87aa82db3..58d56adb9842 100644
--- a/include/linux/mlx5/port.h
+++ b/include/linux/mlx5/port.h
@@ -209,6 +209,8 @@ void mlx5_query_port_fcs(struct mlx5_core_dev *mdev, bool *supported,
 			 bool *enabled);
 int mlx5_query_module_eeprom(struct mlx5_core_dev *dev,
 			     u16 offset, u16 size, u8 *data);
+int mlx5_query_module_eeprom_by_page(struct mlx5_core_dev *dev,
+				     struct mlx5_module_eeprom_query_params *params, u8 *data);
 
 int mlx5_query_port_dcbx_param(struct mlx5_core_dev *mdev, u32 *out);
 int mlx5_set_port_dcbx_param(struct mlx5_core_dev *mdev, u32 *in);
-- 
2.26.2

[PATCH net-next 4/8] net/mlx5: Add support for DSFP module EEPROM dumps

[Moshe Shemesh]

From: Vladyslav Tarasiuk <vladyslavt@nvidia.com>

Allow the driver to recognise DSFP transceiver module ID and therefore
allow its EEPROM dumps using ethtool.

Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
---
 drivers/net/ethernet/mellanox/mlx5/core/port.c | 2 ++
 include/linux/mlx5/port.h                      | 1 +
 2 files changed, 3 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlx5/core/port.c b/drivers/net/ethernet/mellanox/mlx5/core/port.c
index 522a41f8f1e2..1ef2b6a848c1 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/port.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/port.c
@@ -454,6 +454,8 @@ int mlx5_query_module_eeprom_by_page(struct mlx5_core_dev *dev,
 		if (params->page > 3)
 			return -EINVAL;
 		break;
+	case MLX5_MODULE_ID_DSFP:
+		break;
 	default:
 		mlx5_core_err(dev, "Module ID not recognized: 0x%x\n", module_id);
 		return -EINVAL;
diff --git a/include/linux/mlx5/port.h b/include/linux/mlx5/port.h
index 58d56adb9842..77ea4f9c5265 100644
--- a/include/linux/mlx5/port.h
+++ b/include/linux/mlx5/port.h
@@ -45,6 +45,7 @@ enum mlx5_module_id {
 	MLX5_MODULE_ID_QSFP             = 0xC,
 	MLX5_MODULE_ID_QSFP_PLUS        = 0xD,
 	MLX5_MODULE_ID_QSFP28           = 0x11,
+	MLX5_MODULE_ID_DSFP		= 0x1B,
 };
 
 enum mlx5_an_status {
-- 
2.26.2

[PATCH net-next 5/8] net: ethtool: Export helpers for getting EEPROM info

[Moshe Shemesh]

From: Andrew Lunn <andrew@lunn.ch>

There are two ways to retrieve information from SFP EEPROMs.  Many
devices make use of the common code, and assign the sfp_bus pointer in
the netdev to point to the bus holding the SFP device. Some MAC
drivers directly implement ops in there ethool structure.

Export within net/ethtool the two helpers used to call these methods,
so that they can also be used in the new netlink code.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
 net/ethtool/common.h |  5 +++++
 net/ethtool/ioctl.c  | 14 +++++++-------
 2 files changed, 12 insertions(+), 7 deletions(-)

diff --git a/net/ethtool/common.h b/net/ethtool/common.h
index a9d071248698..2dc2b80aea5f 100644
--- a/net/ethtool/common.h
+++ b/net/ethtool/common.h
@@ -47,4 +47,9 @@ int __ethtool_get_ts_info(struct net_device *dev, struct ethtool_ts_info *info);
 
 extern const struct ethtool_phy_ops *ethtool_phy_ops;
 
+int ethtool_get_module_info_call(struct net_device *dev,
+				 struct ethtool_modinfo *modinfo);
+int ethtool_get_module_eeprom_call(struct net_device *dev,
+				   struct ethtool_eeprom *ee, u8 *data);
+
 #endif /* _ETHTOOL_COMMON_H */
diff --git a/net/ethtool/ioctl.c b/net/ethtool/ioctl.c
index 26b3e7086075..eec8e588894b 100644
--- a/net/ethtool/ioctl.c
+++ b/net/ethtool/ioctl.c
@@ -2204,8 +2204,8 @@ static int ethtool_get_ts_info(struct net_device *dev, void __user *useraddr)
 	return 0;
 }
 
-static int __ethtool_get_module_info(struct net_device *dev,
-				     struct ethtool_modinfo *modinfo)
+int ethtool_get_module_info_call(struct net_device *dev,
+				 struct ethtool_modinfo *modinfo)
 {
 	const struct ethtool_ops *ops = dev->ethtool_ops;
 	struct phy_device *phydev = dev->phydev;
@@ -2231,7 +2231,7 @@ static int ethtool_get_module_info(struct net_device *dev,
 	if (copy_from_user(&modinfo, useraddr, sizeof(modinfo)))
 		return -EFAULT;
 
-	ret = __ethtool_get_module_info(dev, &modinfo);
+	ret = ethtool_get_module_info_call(dev, &modinfo);
 	if (ret)
 		return ret;
 
@@ -2241,8 +2241,8 @@ static int ethtool_get_module_info(struct net_device *dev,
 	return 0;
 }
 
-static int __ethtool_get_module_eeprom(struct net_device *dev,
-				       struct ethtool_eeprom *ee, u8 *data)
+int ethtool_get_module_eeprom_call(struct net_device *dev,
+				   struct ethtool_eeprom *ee, u8 *data)
 {
 	const struct ethtool_ops *ops = dev->ethtool_ops;
 	struct phy_device *phydev = dev->phydev;
@@ -2265,12 +2265,12 @@ static int ethtool_get_module_eeprom(struct net_device *dev,
 	int ret;
 	struct ethtool_modinfo modinfo;
 
-	ret = __ethtool_get_module_info(dev, &modinfo);
+	ret = ethtool_get_module_info_call(dev, &modinfo);
 	if (ret)
 		return ret;
 
 	return ethtool_get_any_eeprom(dev, useraddr,
-				      __ethtool_get_module_eeprom,
+				      ethtool_get_module_eeprom_call,
 				      modinfo.eeprom_len);
 }
 
-- 
2.26.2

[PATCH net-next 6/8] ethtool: Add fallback to get_module_eeprom from netlink command

[Moshe Shemesh]

From: Vladyslav Tarasiuk <vladyslavt@nvidia.com>

In case netlink get_module_eeprom_by_page() callback is not implemented
by the driver, try to call old get_module_info() and get_module_eeprom()
pair. Recalculate parameters to get_module_eeprom() offset and len using
page number and their sizes. Return error if this can't be done.

Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
 net/ethtool/eeprom.c | 62 +++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 61 insertions(+), 1 deletion(-)

diff --git a/net/ethtool/eeprom.c b/net/ethtool/eeprom.c
index 8536dd905da5..1a49c133d401 100644
--- a/net/ethtool/eeprom.c
+++ b/net/ethtool/eeprom.c
@@ -25,6 +25,66 @@ struct eeprom_reply_data {
 #define MODULE_EEPROM_REPDATA(__reply_base) \
 	container_of(__reply_base, struct eeprom_reply_data, base)
 
+static int fallback_set_params(struct eeprom_req_info *request,
+			       struct ethtool_modinfo *modinfo,
+			       struct ethtool_eeprom *eeprom)
+{
+	u32 offset = request->offset;
+	u32 length = request->length;
+
+	if (request->page)
+		offset = request->page * ETH_MODULE_EEPROM_PAGE_LEN + offset;
+
+	if (modinfo->type == ETH_MODULE_SFF_8079 &&
+	    request->i2c_address == 0x51)
+		offset += ETH_MODULE_EEPROM_PAGE_LEN * 2;
+
+	if (offset >= modinfo->eeprom_len)
+		return -EINVAL;
+
+	eeprom->cmd = ETHTOOL_GMODULEEEPROM;
+	eeprom->len = length;
+	eeprom->offset = offset;
+
+	return 0;
+}
+
+static int eeprom_fallback(struct eeprom_req_info *request,
+			   struct eeprom_reply_data *reply,
+			   struct genl_info *info)
+{
+	struct net_device *dev = reply->base.dev;
+	struct ethtool_modinfo modinfo = {0};
+	struct ethtool_eeprom eeprom = {0};
+	u8 *data;
+	int err;
+
+	modinfo.cmd = ETHTOOL_GMODULEINFO;
+	err = ethtool_get_module_info_call(dev, &modinfo);
+	if (err < 0)
+		return err;
+
+	err = fallback_set_params(request, &modinfo, &eeprom);
+	if (err < 0)
+		return err;
+
+	data = kmalloc(eeprom.len, GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+	err = ethtool_get_module_eeprom_call(dev, &eeprom, data);
+	if (err < 0)
+		goto err_out;
+
+	reply->data = data;
+	reply->length = eeprom.len;
+
+	return 0;
+
+err_out:
+	kfree(data);
+	return err;
+}
+
 static int eeprom_prepare_data(const struct ethnl_req_info *req_base,
 			       struct ethnl_reply_data *reply_base,
 			       struct genl_info *info)
@@ -36,7 +96,7 @@ static int eeprom_prepare_data(const struct ethnl_req_info *req_base,
 	int ret;
 
 	if (!dev->ethtool_ops->get_module_eeprom_by_page)
-		return -EOPNOTSUPP;
+		return eeprom_fallback(request, reply, info);
 
 	page_data.offset = request->offset;
 	page_data.length = request->length;
-- 
2.26.2

[PATCH net-next 7/8] phy: sfp: add netlink SFP support to generic SFP code

[Moshe Shemesh]

From: Andrew Lunn <andrew@lunn.ch>

The new netlink API for reading SFP data requires a new op to be
implemented. The idea of the new netlink SFP code is that userspace is
responsible to parsing the EEPROM data and requesting pages, rather
than have the kernel decide what pages are interesting and returning
them. This allows greater flexibility for newer formats.

Currently the generic SFP code only supports simple SFPs. Allow i2c
address 0x50 and 0x51 to be accessed with page and bank must always be
0. This interface will later be extended when for example QSFP support
is added.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
---
 drivers/net/phy/sfp-bus.c | 20 ++++++++++++++++++++
 drivers/net/phy/sfp.c     | 25 +++++++++++++++++++++++++
 drivers/net/phy/sfp.h     |  3 +++
 include/linux/sfp.h       | 10 ++++++++++
 4 files changed, 58 insertions(+)

diff --git a/drivers/net/phy/sfp-bus.c b/drivers/net/phy/sfp-bus.c
index 2e11176c6b94..e61de66e973b 100644
--- a/drivers/net/phy/sfp-bus.c
+++ b/drivers/net/phy/sfp-bus.c
@@ -555,6 +555,26 @@ int sfp_get_module_eeprom(struct sfp_bus *bus, struct ethtool_eeprom *ee,
 }
 EXPORT_SYMBOL_GPL(sfp_get_module_eeprom);
 
+/**
+ * sfp_get_module_eeprom_by_page() - Read a page from the SFP module EEPROM
+ * @bus: a pointer to the &struct sfp_bus structure for the sfp module
+ * @page: a &struct ethtool_module_eeprom
+ * @extack: extack for reporting problems
+ *
+ * Read an EEPROM page as specified by the supplied @page. See the
+ * documentation for &struct ethtool_module_eeprom for the page to be read.
+ *
+ * Returns 0 on success or a negative errno number. More error
+ * information might be provided via extack
+ */
+int sfp_get_module_eeprom_by_page(struct sfp_bus *bus,
+				  const struct ethtool_module_eeprom *page,
+				  struct netlink_ext_ack *extack)
+{
+	return bus->socket_ops->module_eeprom_by_page(bus->sfp, page, extack);
+}
+EXPORT_SYMBOL_GPL(sfp_get_module_eeprom_by_page);
+
 /**
  * sfp_upstream_start() - Inform the SFP that the network device is up
  * @bus: a pointer to the &struct sfp_bus structure for the sfp module
diff --git a/drivers/net/phy/sfp.c b/drivers/net/phy/sfp.c
index 7998acc689b7..37f722c763d7 100644
--- a/drivers/net/phy/sfp.c
+++ b/drivers/net/phy/sfp.c
@@ -2330,6 +2330,30 @@ static int sfp_module_eeprom(struct sfp *sfp, struct ethtool_eeprom *ee,
 	return 0;
 }
 
+static int sfp_module_eeprom_by_page(struct sfp *sfp,
+				     const struct ethtool_module_eeprom *page,
+				     struct netlink_ext_ack *extack)
+{
+	if (page->bank) {
+		NL_SET_ERR_MSG(extack, "Banks not supported");
+		return -EOPNOTSUPP;
+	}
+
+	if (page->page) {
+		NL_SET_ERR_MSG(extack, "Only page 0 supported");
+		return -EOPNOTSUPP;
+	}
+
+	if (page->i2c_address != 0x50 &&
+	    page->i2c_address != 0x51) {
+		NL_SET_ERR_MSG(extack, "Only address 0x50 and 0x51 supported");
+		return -EOPNOTSUPP;
+	}
+
+	return sfp_read(sfp, page->i2c_address == 0x51, page->offset,
+			page->data, page->length);
+};
+
 static const struct sfp_socket_ops sfp_module_ops = {
 	.attach = sfp_attach,
 	.detach = sfp_detach,
@@ -2337,6 +2361,7 @@ static const struct sfp_socket_ops sfp_module_ops = {
 	.stop = sfp_stop,
 	.module_info = sfp_module_info,
 	.module_eeprom = sfp_module_eeprom,
+	.module_eeprom_by_page = sfp_module_eeprom_by_page,
 };
 
 static void sfp_timeout(struct work_struct *work)
diff --git a/drivers/net/phy/sfp.h b/drivers/net/phy/sfp.h
index b83f70526270..27226535c72b 100644
--- a/drivers/net/phy/sfp.h
+++ b/drivers/net/phy/sfp.h
@@ -14,6 +14,9 @@ struct sfp_socket_ops {
 	int (*module_info)(struct sfp *sfp, struct ethtool_modinfo *modinfo);
 	int (*module_eeprom)(struct sfp *sfp, struct ethtool_eeprom *ee,
 			     u8 *data);
+	int (*module_eeprom_by_page)(struct sfp *sfp,
+				     const struct ethtool_module_eeprom *page,
+				     struct netlink_ext_ack *extack);
 };
 
 int sfp_add_phy(struct sfp_bus *bus, struct phy_device *phydev);
diff --git a/include/linux/sfp.h b/include/linux/sfp.h
index 38893e4dd0f0..302094b855fb 100644
--- a/include/linux/sfp.h
+++ b/include/linux/sfp.h
@@ -542,6 +542,9 @@ phy_interface_t sfp_select_interface(struct sfp_bus *bus,
 int sfp_get_module_info(struct sfp_bus *bus, struct ethtool_modinfo *modinfo);
 int sfp_get_module_eeprom(struct sfp_bus *bus, struct ethtool_eeprom *ee,
 			  u8 *data);
+int sfp_get_module_eeprom_by_page(struct sfp_bus *bus,
+				  const struct ethtool_module_eeprom *page,
+				  struct netlink_ext_ack *extack);
 void sfp_upstream_start(struct sfp_bus *bus);
 void sfp_upstream_stop(struct sfp_bus *bus);
 void sfp_bus_put(struct sfp_bus *bus);
@@ -587,6 +590,13 @@ static inline int sfp_get_module_eeprom(struct sfp_bus *bus,
 	return -EOPNOTSUPP;
 }
 
+static inline int sfp_get_module_eeprom_by_page(struct sfp_bus *bus,
+						const struct ethtool_module_eeprom *page,
+						struct netlink_ext_ack *extack)
+{
+	return -EOPNOTSUPP;
+}
+
 static inline void sfp_upstream_start(struct sfp_bus *bus)
 {
 }
-- 
2.26.2

[PATCH net-next 8/8] ethtool: wire in generic SFP module access

[Moshe Shemesh]

From: Andrew Lunn <andrew@lunn.ch>

If the device has a sfp bus attached, call its
sfp_get_module_eeprom_by_page() function, otherwise use the ethtool op
for the device. This follows how the IOCTL works.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
 net/ethtool/eeprom.c | 25 ++++++++++++++++++++-----
 1 file changed, 20 insertions(+), 5 deletions(-)

diff --git a/net/ethtool/eeprom.c b/net/ethtool/eeprom.c
index 1a49c133d401..2a6733a6449a 100644
--- a/net/ethtool/eeprom.c
+++ b/net/ethtool/eeprom.c
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 
 #include <linux/ethtool.h>
+#include <linux/sfp.h>
 #include "netlink.h"
 #include "common.h"
 
@@ -85,6 +86,21 @@ static int eeprom_fallback(struct eeprom_req_info *request,
 	return err;
 }
 
+static int get_module_eeprom_by_page(struct net_device *dev,
+				     struct ethtool_module_eeprom *page_data,
+				     struct netlink_ext_ack *extack)
+{
+	const struct ethtool_ops *ops = dev->ethtool_ops;
+
+	if (dev->sfp_bus)
+		return sfp_get_module_eeprom_by_page(dev->sfp_bus, page_data, extack);
+
+	if (ops->get_module_info)
+		return ops->get_module_eeprom_by_page(dev, page_data, extack);
+
+	return -EOPNOTSUPP;
+}
+
 static int eeprom_prepare_data(const struct ethnl_req_info *req_base,
 			       struct ethnl_reply_data *reply_base,
 			       struct genl_info *info)
@@ -95,9 +111,6 @@ static int eeprom_prepare_data(const struct ethnl_req_info *req_base,
 	struct net_device *dev = reply_base->dev;
 	int ret;
 
-	if (!dev->ethtool_ops->get_module_eeprom_by_page)
-		return eeprom_fallback(request, reply, info);
-
 	page_data.offset = request->offset;
 	page_data.length = request->length;
 	page_data.i2c_address = request->i2c_address;
@@ -111,8 +124,7 @@ static int eeprom_prepare_data(const struct ethnl_req_info *req_base,
 	if (ret)
 		goto err_free;
 
-	ret = dev->ethtool_ops->get_module_eeprom_by_page(dev, &page_data,
-							  info->extack);
+	ret = get_module_eeprom_by_page(dev, &page_data, info->extack);
 	if (ret < 0)
 		goto err_ops;
 
@@ -126,6 +138,9 @@ static int eeprom_prepare_data(const struct ethnl_req_info *req_base,
 	ethnl_ops_complete(dev);
 err_free:
 	kfree(page_data.data);
+
+	if (ret == -EOPNOTSUPP)
+		return eeprom_fallback(request, reply, info);
 	return ret;
 }
 
-- 
2.26.2

Re: [PATCH net-next 0/8] ethtool: Extend module EEPROM dump API

[patchwork-bot+netdevbpf]

Hello:

This series was applied to netdev/net-next.git (refs/heads/master):

On Fri, 9 Apr 2021 11:06:33 +0300 you wrote:
> Ethtool supports module EEPROM dumps via the `ethtool -m <dev>` command.
> But in current state its functionality is limited - offset and length
> parameters, which are used to specify a linear desired region of EEPROM
> data to dump, is not enough, considering emergence of complex module
> EEPROM layouts such as CMIS 4.0.
> Moreover, CMIS 4.0 extends the amount of pages that may be accessible by
> introducing another parameter for page addressing - banks.
> 
> [...]

Here is the summary with links:
  - [net-next,1/8] ethtool: Allow network drivers to dump arbitrary EEPROM data
    https://git.kernel.org/netdev/net-next/c/c781ff12a2f3
  - [net-next,2/8] net/mlx5: Refactor module EEPROM query
    https://git.kernel.org/netdev/net-next/c/e19b0a3474ab
  - [net-next,3/8] net/mlx5: Implement get_module_eeprom_by_page()
    https://git.kernel.org/netdev/net-next/c/e109d2b204da
  - [net-next,4/8] net/mlx5: Add support for DSFP module EEPROM dumps
    https://git.kernel.org/netdev/net-next/c/4c88fa412a10
  - [net-next,5/8] net: ethtool: Export helpers for getting EEPROM info
    https://git.kernel.org/netdev/net-next/c/95dfc7effd88
  - [net-next,6/8] ethtool: Add fallback to get_module_eeprom from netlink command
    https://git.kernel.org/netdev/net-next/c/96d971e307cc
  - [net-next,7/8] phy: sfp: add netlink SFP support to generic SFP code
    https://git.kernel.org/netdev/net-next/c/d740513f05a2
  - [net-next,8/8] ethtool: wire in generic SFP module access
    https://git.kernel.org/netdev/net-next/c/c97a31f66ebc

You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html