[PATCH v6 0/7] ARM: mvebu: switch to DT probed mv643xx_eth

[PATCH v6 0/7] ARM: mvebu: switch to DT probed mv643xx_eth

[Sebastian Hesselbarth]

This patch set converts Marvell Dove, Kirkwood, and Orion5x DT enabled
boards to probe mv643xx_eth by DT. The corresponding DT support patches
for mv643xx_eth driver have already been taked by David Miller and are
available in next-20130701. This only contains the ARM part of
mv643xx_eth DT support patches and therefore patch counting is
continued as v6 with respect to the combined patch set.

The first three patches add nodes for ethernet-controller, mdio-bus,
and ethernet PHYs found on the three SoCs and their boards.

The last four patches convert DT boards for each SoC from platform_device
registration to DT based probing by removing the corresponding calls.
For Kirkwood this makes almost all DT board setup (except board-dnskw)
obsolete. Therefore, patch 5 removes board setup files, Kconfig, Makefile,
and defconfig entries for those boards.

This patch set has been tested on Marvell Dove, and compile-tested for
Kirkwood and Orion5x defconfig on top of next-20130701 with some fixes
sent earlier applied (DMA_MEMSET fixes and missing include on edmini_v2).

netdev is added on Cc for completeness, this is all Marvell related and
should go through Jason Cooper's branch if there are no objections.

Sebastian Hesselbarth (7):
  ARM: dove: add gigabit ethernet and mvmdio device tree nodes
  ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes
  ARM: orion5x: add gigabit ethernet and mvmdio device tree nodes
  ARM: dove: remove legacy mv643xx_eth setup
  ARM: kirkwood: remove redundant DT board files
  ARM: kirkwood: remove legacy clk alias for mv643xx_eth
  ARM: orion5x: remove legacy mv643xx_eth board setup

 arch/arm/boot/dts/dove-cubox.dts                   |    7 +
 arch/arm/boot/dts/dove.dtsi                        |   35 +++++
 arch/arm/boot/dts/kirkwood-cloudbox.dts            |   16 ++
 arch/arm/boot/dts/kirkwood-db.dtsi                 |   16 ++
 arch/arm/boot/dts/kirkwood-dnskw.dtsi              |   16 ++
 arch/arm/boot/dts/kirkwood-dockstar.dts            |   17 ++
 arch/arm/boot/dts/kirkwood-dreamplug.dts           |   28 ++++
 arch/arm/boot/dts/kirkwood-goflexnet.dts           |   16 ++
 .../arm/boot/dts/kirkwood-guruplug-server-plus.dts |   30 ++++
 arch/arm/boot/dts/kirkwood-ib62x0.dts              |   16 ++
 arch/arm/boot/dts/kirkwood-iconnect.dts            |   16 ++
 arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts      |   24 +++
 arch/arm/boot/dts/kirkwood-is2.dts                 |    2 +
 arch/arm/boot/dts/kirkwood-km_kirkwood.dts         |   16 ++
 arch/arm/boot/dts/kirkwood-lsxl.dtsi               |   28 ++++
 arch/arm/boot/dts/kirkwood-mplcec4.dts             |   27 ++++
 .../boot/dts/kirkwood-netgear_readynas_duo_v2.dts  |   16 ++
 arch/arm/boot/dts/kirkwood-ns2-common.dtsi         |   16 ++
 arch/arm/boot/dts/kirkwood-ns2.dts                 |    2 +
 arch/arm/boot/dts/kirkwood-ns2lite.dts             |    2 +
 arch/arm/boot/dts/kirkwood-ns2max.dts              |    2 +
 arch/arm/boot/dts/kirkwood-ns2mini.dts             |    2 +
 arch/arm/boot/dts/kirkwood-openblocks_a6.dts       |   16 ++
 arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi  |   16 ++
 arch/arm/boot/dts/kirkwood-topkick.dts             |   16 ++
 arch/arm/boot/dts/kirkwood-ts219-6281.dts          |    4 +-
 arch/arm/boot/dts/kirkwood-ts219-6282.dts          |    4 +-
 arch/arm/boot/dts/kirkwood-ts219.dtsi              |   16 ++
 arch/arm/boot/dts/kirkwood.dtsi                    |   52 +++++++
 .../dts/orion5x-lacie-ethernet-disk-mini-v2.dts    |   17 ++
 arch/arm/boot/dts/orion5x.dtsi                     |   29 ++++
 arch/arm/configs/kirkwood_defconfig                |   22 ---
 arch/arm/mach-dove/board-dt.c                      |    9 -
 arch/arm/mach-kirkwood/Kconfig                     |  156 --------------------
 arch/arm/mach-kirkwood/Makefile                    |   23 +---
 arch/arm/mach-kirkwood/board-db88f628x-bp.c        |   24 ---
 arch/arm/mach-kirkwood/board-dnskw.c               |    7 -
 arch/arm/mach-kirkwood/board-dockstar.c            |   32 ----
 arch/arm/mach-kirkwood/board-dreamplug.c           |   35 -----
 arch/arm/mach-kirkwood/board-dt.c                  |   86 +-----------
 arch/arm/mach-kirkwood/board-goflexnet.c           |   34 -----
 arch/arm/mach-kirkwood/board-guruplug.c            |   33 ----
 arch/arm/mach-kirkwood/board-ib62x0.c              |   29 ----
 arch/arm/mach-kirkwood/board-iconnect.c            |   24 ---
 arch/arm/mach-kirkwood/board-iomega_ix2_200.c      |   34 -----
 arch/arm/mach-kirkwood/board-km_kirkwood.c         |   44 ------
 arch/arm/mach-kirkwood/board-lsxl.c                |   36 -----
 arch/arm/mach-kirkwood/board-mplcec4.c             |   35 -----
 arch/arm/mach-kirkwood/board-ns2.c                 |   35 -----
 arch/arm/mach-kirkwood/board-openblocks_a6.c       |   26 ----
 arch/arm/mach-kirkwood/board-readynas.c            |   27 ----
 arch/arm/mach-kirkwood/board-sheevaplug.c          |   27 ----
 arch/arm/mach-kirkwood/board-ts219.c               |   40 -----
 arch/arm/mach-kirkwood/board-usi_topkick.c         |   29 ----
 arch/arm/mach-orion5x/edmini_v2-setup.c            |   10 --
 55 files changed, 520 insertions(+), 857 deletions(-)
 delete mode 100644 arch/arm/mach-kirkwood/board-db88f628x-bp.c
 delete mode 100644 arch/arm/mach-kirkwood/board-dockstar.c
 delete mode 100644 arch/arm/mach-kirkwood/board-dreamplug.c
 delete mode 100644 arch/arm/mach-kirkwood/board-goflexnet.c
 delete mode 100644 arch/arm/mach-kirkwood/board-guruplug.c
 delete mode 100644 arch/arm/mach-kirkwood/board-ib62x0.c
 delete mode 100644 arch/arm/mach-kirkwood/board-iconnect.c
 delete mode 100644 arch/arm/mach-kirkwood/board-iomega_ix2_200.c
 delete mode 100644 arch/arm/mach-kirkwood/board-km_kirkwood.c
 delete mode 100644 arch/arm/mach-kirkwood/board-lsxl.c
 delete mode 100644 arch/arm/mach-kirkwood/board-mplcec4.c
 delete mode 100644 arch/arm/mach-kirkwood/board-ns2.c
 delete mode 100644 arch/arm/mach-kirkwood/board-openblocks_a6.c
 delete mode 100644 arch/arm/mach-kirkwood/board-readynas.c
 delete mode 100644 arch/arm/mach-kirkwood/board-sheevaplug.c
 delete mode 100644 arch/arm/mach-kirkwood/board-ts219.c
 delete mode 100644 arch/arm/mach-kirkwood/board-usi_topkick.c

---
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
-- 
1.7.2.5

[PATCH v6 1/7] ARM: dove: add gigabit ethernet and mvmdio device tree nodes

[Sebastian Hesselbarth]

This patch adds orion-eth and mvmdio device tree nodes for DT enabled
Dove boards. As there is only one ethernet controller on Dove, a default
phy node is also added with a note to set its reg property on a per-board
basis.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Changelog:
v5->v6:
- rebase for v3.11-rc1

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
---
 arch/arm/boot/dts/dove-cubox.dts |    7 +++++++
 arch/arm/boot/dts/dove.dtsi      |   35 +++++++++++++++++++++++++++++++++++
 2 files changed, 42 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts
index 5cae2ab..955188f 100644
--- a/arch/arm/boot/dts/dove-cubox.dts
+++ b/arch/arm/boot/dts/dove-cubox.dts
@@ -57,6 +57,13 @@
 
 &uart0 { status = "okay"; };
 &sata0 { status = "okay"; };
+&mdio { status = "okay"; };
+&eth { status = "okay"; };
+
+&ethphy {
+	compatible = "marvell,88e1310";
+	reg = <1>;
+};
 
 &i2c0 {
 	status = "okay";
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi
index 2cef34f..5e394a6 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/dove.dtsi
@@ -256,5 +256,40 @@
 				dmacap,xor;
 			};
 		};
+
+		mdio: mdio-bus@72004 {
+			compatible = "marvell,orion-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72004 0x84>;
+			interrupts = <30>;
+			clocks = <&gate_clk 2>;
+			status = "disabled";
+
+			ethphy: ethernet-phy {
+				device-type = "ethernet-phy";
+				/* set phy address in board file */
+			};
+		};
+
+		eth: ethernet-controller@72000 {
+			compatible = "marvell,orion-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72000 0x4000>;
+			clocks = <&gate_clk 2>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet-port@0 {
+				device_type = "network";
+				compatible = "marvell,orion-eth-port";
+				reg = <0>;
+				interrupts = <29>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				phy-handle = <&ethphy>;
+			};
+		};
 	};
 };
-- 
1.7.2.5

[PATCH v6 2/7] ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes

[Sebastian Hesselbarth]

This patch adds mv643xx_eth and mvmdio device tree nodes for DT enabled
Kirkwood boards. Phy nodes are also added with reg property set on a
per-board basis.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Changelog:
v5->v6:
- rebase for v3.11-rc1
- also convert Sheevaplug and DB628x

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
---
 arch/arm/boot/dts/kirkwood-cloudbox.dts            |   16 ++++++
 arch/arm/boot/dts/kirkwood-db.dtsi                 |   16 ++++++
 arch/arm/boot/dts/kirkwood-dnskw.dtsi              |   16 ++++++
 arch/arm/boot/dts/kirkwood-dockstar.dts            |   17 ++++++
 arch/arm/boot/dts/kirkwood-dreamplug.dts           |   28 +++++++++++
 arch/arm/boot/dts/kirkwood-goflexnet.dts           |   16 ++++++
 .../arm/boot/dts/kirkwood-guruplug-server-plus.dts |   30 +++++++++++
 arch/arm/boot/dts/kirkwood-ib62x0.dts              |   16 ++++++
 arch/arm/boot/dts/kirkwood-iconnect.dts            |   16 ++++++
 arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts      |   24 +++++++++
 arch/arm/boot/dts/kirkwood-is2.dts                 |    2 +
 arch/arm/boot/dts/kirkwood-km_kirkwood.dts         |   16 ++++++
 arch/arm/boot/dts/kirkwood-lsxl.dtsi               |   28 +++++++++++
 arch/arm/boot/dts/kirkwood-mplcec4.dts             |   27 ++++++++++
 .../boot/dts/kirkwood-netgear_readynas_duo_v2.dts  |   16 ++++++
 arch/arm/boot/dts/kirkwood-ns2-common.dtsi         |   16 ++++++
 arch/arm/boot/dts/kirkwood-ns2.dts                 |    2 +
 arch/arm/boot/dts/kirkwood-ns2lite.dts             |    2 +
 arch/arm/boot/dts/kirkwood-ns2max.dts              |    2 +
 arch/arm/boot/dts/kirkwood-ns2mini.dts             |    2 +
 arch/arm/boot/dts/kirkwood-openblocks_a6.dts       |   16 ++++++
 arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi  |   16 ++++++
 arch/arm/boot/dts/kirkwood-topkick.dts             |   16 ++++++
 arch/arm/boot/dts/kirkwood-ts219-6281.dts          |    4 +-
 arch/arm/boot/dts/kirkwood-ts219-6282.dts          |    4 +-
 arch/arm/boot/dts/kirkwood-ts219.dtsi              |   16 ++++++
 arch/arm/boot/dts/kirkwood.dtsi                    |   52 ++++++++++++++++++++
 27 files changed, 430 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/kirkwood-cloudbox.dts b/arch/arm/boot/dts/kirkwood-cloudbox.dts
index 00c48d2..85eed62 100644
--- a/arch/arm/boot/dts/kirkwood-cloudbox.dts
+++ b/arch/arm/boot/dts/kirkwood-cloudbox.dts
@@ -89,3 +89,19 @@
 		gpios = <&gpio0 17 0>;
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-db.dtsi b/arch/arm/boot/dts/kirkwood-db.dtsi
index c87cfb8..ca8bf36 100644
--- a/arch/arm/boot/dts/kirkwood-db.dtsi
+++ b/arch/arm/boot/dts/kirkwood-db.dtsi
@@ -87,3 +87,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-dnskw.dtsi b/arch/arm/boot/dts/kirkwood-dnskw.dtsi
index 0afe1d0..f600ed7 100644
--- a/arch/arm/boot/dts/kirkwood-dnskw.dtsi
+++ b/arch/arm/boot/dts/kirkwood-dnskw.dtsi
@@ -219,3 +219,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/kirkwood-dockstar.dts
index 7714742..915aca6 100644
--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
@@ -90,3 +90,20 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		compatible = "marvell,88e1116";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/kirkwood-dreamplug.dts
index 36c7ba3..300fbf8 100644
--- a/arch/arm/boot/dts/kirkwood-dreamplug.dts
+++ b/arch/arm/boot/dts/kirkwood-dreamplug.dts
@@ -99,3 +99,31 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		device_type = "ethernet-phy";
+		reg = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts
index 31caa64..e9ba68e 100644
--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
@@ -170,3 +170,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts b/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
index 1e642f3..e696c31 100644
--- a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
+++ b/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
@@ -96,3 +96,33 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		compatible = "marvell,88e1121";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		device_type = "ethernet-phy";
+		compatible = "marvell,88e1121";
+		reg = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/kirkwood-ib62x0.dts
index 20c4b08..69019b8 100644
--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
+++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
@@ -122,3 +122,19 @@
 
 
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts
index 441204e..3d99164 100644
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
@@ -176,3 +176,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@11 {
+		device_type = "ethernet-phy";
+		reg = <11>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
index 00a7bfe..b08c733 100644
--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
@@ -194,3 +194,27 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy1: ethernet-phy@11 {
+		device_type = "ethernet-phy";
+		reg = <11>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-is2.dts b/arch/arm/boot/dts/kirkwood-is2.dts
index c3f036b..ff9be45 100644
--- a/arch/arm/boot/dts/kirkwood-is2.dts
+++ b/arch/arm/boot/dts/kirkwood-is2.dts
@@ -30,3 +30,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
index 5d9f5ea..466280b 100644
--- a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
+++ b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
@@ -50,3 +50,19 @@
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-lsxl.dtsi b/arch/arm/boot/dts/kirkwood-lsxl.dtsi
index 31b17f5..93397b1 100644
--- a/arch/arm/boot/dts/kirkwood-lsxl.dtsi
+++ b/arch/arm/boot/dts/kirkwood-lsxl.dtsi
@@ -207,3 +207,31 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-mplcec4.dts b/arch/arm/boot/dts/kirkwood-mplcec4.dts
index 6179333..def825f 100644
--- a/arch/arm/boot/dts/kirkwood-mplcec4.dts
+++ b/arch/arm/boot/dts/kirkwood-mplcec4.dts
@@ -191,3 +191,30 @@
 	};
 };
 
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@1 {
+		device_type = "ethernet-phy";
+		reg = <1>;
+	};
+
+	ethphy1: ethernet-phy@2 {
+		device_type = "ethernet-phy";
+		reg = <2>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
index ad6ade7..716b203 100644
--- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
+++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
@@ -184,3 +184,19 @@
                 };
         };
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
index 2afac04..e7b8017 100644
--- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
@@ -84,3 +84,19 @@
 	};
 
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy {
+		device_type = "ethernet-phy";
+                /* overwrite reg property in board file */
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ns2.dts b/arch/arm/boot/dts/kirkwood-ns2.dts
index b50e93d..e93276d 100644
--- a/arch/arm/boot/dts/kirkwood-ns2.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2.dts
@@ -30,3 +30,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-ns2lite.dts b/arch/arm/boot/dts/kirkwood-ns2lite.dts
index af8259f..34f5e69 100644
--- a/arch/arm/boot/dts/kirkwood-ns2lite.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2lite.dts
@@ -30,3 +30,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <0>; };
diff --git a/arch/arm/boot/dts/kirkwood-ns2max.dts b/arch/arm/boot/dts/kirkwood-ns2max.dts
index 85f24d2..f834c55 100644
--- a/arch/arm/boot/dts/kirkwood-ns2max.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2max.dts
@@ -49,3 +49,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-ns2mini.dts b/arch/arm/boot/dts/kirkwood-ns2mini.dts
index 329e530..b6b66ea 100644
--- a/arch/arm/boot/dts/kirkwood-ns2mini.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2mini.dts
@@ -50,3 +50,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <0>; };
diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
index 38dc851..7235f0c 100644
--- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
+++ b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
@@ -166,3 +166,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
index f7143f1..f55a145 100644
--- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
@@ -91,3 +91,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-topkick.dts b/arch/arm/boot/dts/kirkwood-topkick.dts
index f2052d7..184b8c5 100644
--- a/arch/arm/boot/dts/kirkwood-topkick.dts
+++ b/arch/arm/boot/dts/kirkwood-topkick.dts
@@ -203,3 +203,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6281.dts b/arch/arm/boot/dts/kirkwood-ts219-6281.dts
index 6dd1038..222435d 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6281.dts
+++ b/arch/arm/boot/dts/kirkwood-ts219-6281.dts
@@ -50,4 +50,6 @@
 			gpios = <&gpio0 16 1>;
 		};
 	};
-};
\ No newline at end of file
+};
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6282.dts b/arch/arm/boot/dts/kirkwood-ts219-6282.dts
index 6fdc5ff..510c555 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6282.dts
+++ b/arch/arm/boot/dts/kirkwood-ts219-6282.dts
@@ -58,4 +58,6 @@
 			gpios = <&gpio1 5 1>;
 		};
 	};
-};
\ No newline at end of file
+};
+
+&ethphy0 { reg = <0>; };
diff --git a/arch/arm/boot/dts/kirkwood-ts219.dtsi b/arch/arm/boot/dts/kirkwood-ts219.dtsi
index 0c9a94c..102eaeb 100644
--- a/arch/arm/boot/dts/kirkwood-ts219.dtsi
+++ b/arch/arm/boot/dts/kirkwood-ts219.dtsi
@@ -96,3 +96,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy {
+		device_type = "ethernet-phy";
+                /* overwrite reg property in board file */
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 078637c..ad56dd8 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -190,5 +190,57 @@
 			clocks = <&gate_clk 17>;
 			status = "okay";
 		};
+
+		mdio: mdio-bus@72004 {
+			compatible = "marvell,orion-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72004 0x84>;
+			interrupts = <46>;
+			clocks = <&gate_clk 0>;
+			status = "disabled";
+
+			/* add phy nodes in board file */
+		};
+
+		eth0: ethernet-controller@72000 {
+			compatible = "marvell,kirkwood-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72000 0x4000>;
+			clocks = <&gate_clk 0>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet0-port@0 {
+				device_type = "network";
+				compatible = "marvell,kirkwood-eth-port";
+				reg = <0>;
+				interrupts = <11>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				/* set phy-handle property in board file */
+			};
+		};
+
+		eth1: ethernet-controller@76000 {
+			compatible = "marvell,kirkwood-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x76000 0x4000>;
+			clocks = <&gate_clk 19>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet1-port@1 {
+				device_type = "network";
+				compatible = "marvell,kirkwood-eth-port";
+				reg = <1>;
+				interrupts = <15>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				/* set phy-handle property in board file */
+			};
+		};
 	};
 };
-- 
1.7.2.5

[PATCH v6 3/7] ARM: orion5x: add gigabit ethernet and mvmdio device tree nodes

[Sebastian Hesselbarth]

This patch adds mv643xx_eth and mvmdio device tree nodes for DT enabled
Orion5x boards. Phy nodes are also added with reg property set on a
per-board basis.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Changelog:
v5->v6:
- rebase for v3.11-rc1

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
---
 .../dts/orion5x-lacie-ethernet-disk-mini-v2.dts    |   17 +++++++++++
 arch/arm/boot/dts/orion5x.dtsi                     |   29 ++++++++++++++++++++
 2 files changed, 46 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
index 0077fc8..aed83de 100644
--- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
+++ b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
@@ -53,3 +53,20 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy: ethernet-phy {
+		device-type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth {
+	status = "okay";
+
+	ethernet-port@0 {
+		phy-handle = <&ethphy>;
+	};
+};
diff --git a/arch/arm/boot/dts/orion5x.dtsi b/arch/arm/boot/dts/orion5x.dtsi
index f82ece7..2d241fc 100644
--- a/arch/arm/boot/dts/orion5x.dtsi
+++ b/arch/arm/boot/dts/orion5x.dtsi
@@ -131,5 +131,34 @@
 			interrupts = <28>;
 			status = "okay";
 		};
+
+		mdio: mdio-bus@72004 {
+			compatible = "marvell,orion-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72004 0x84>;
+			interrupts = <22>;
+			status = "disabled";
+
+			/* add phy nodes in board file */
+		};
+
+		eth: ethernet-controller@72000 {
+			compatible = "marvell,orion-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72000 0x4000>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet-port@0 {
+				device_type = "network";
+				compatible = "marvell,orion-eth-port";
+				reg = <0>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				/* set phy-handle property in board file */
+			};
+		};
 	};
 };
-- 
1.7.2.5

[PATCH v6 4/7] ARM: dove: remove legacy mv643xx_eth setup

[Sebastian Hesselbarth]

With DT support for mv643xx_eth we do not need legacy platform_data
based setup for DT enabled boards anymore.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Changelog:
v5->v6:
- rebase for v3.11-rc1

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
---
 arch/arm/mach-dove/board-dt.c |    9 ---------
 1 files changed, 0 insertions(+), 9 deletions(-)

diff --git a/arch/arm/mach-dove/board-dt.c b/arch/arm/mach-dove/board-dt.c
index f3755ac..b5ccc1c 100644
--- a/arch/arm/mach-dove/board-dt.c
+++ b/arch/arm/mach-dove/board-dt.c
@@ -33,10 +33,6 @@ static void __init dove_legacy_clk_init(void)
 	clkspec.np = np;
 	clkspec.args_count = 1;
 
-	clkspec.args[0] = CLOCK_GATING_BIT_GBE;
-	orion_clkdev_add(NULL, "mv643xx_eth_port.0",
-			 of_clk_get_from_provider(&clkspec));
-
 	clkspec.args[0] = CLOCK_GATING_BIT_PCIE0;
 	orion_clkdev_add("0", "pcie",
 			 of_clk_get_from_provider(&clkspec));
@@ -52,10 +48,6 @@ static void __init dove_of_clk_init(void)
 	dove_legacy_clk_init();
 }
 
-static struct mv643xx_eth_platform_data dove_dt_ge00_data = {
-	.phy_addr = MV643XX_ETH_PHY_ADDR_DEFAULT,
-};
-
 static void __init dove_dt_init(void)
 {
 	pr_info("Dove 88AP510 SoC\n");
@@ -69,7 +61,6 @@ static void __init dove_dt_init(void)
 	dove_of_clk_init();
 
 	/* Internal devices not ported to DT yet */
-	dove_ge00_init(&dove_dt_ge00_data);
 	dove_pcie_init(1, 1);
 
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
-- 
1.7.2.5

[PATCH v6 5/7] ARM: kirkwood: remove redundant DT board files

[Sebastian Hesselbarth]

With DT support for mv643xx_eth board specific init for some boards now
is unneccessary. Remove those board files, Kconfig entries, and
corresponding entries in kirkwood_defconfig.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Changelog:
v5->v6:
- rebase for v3.11-rc1

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
---
 arch/arm/configs/kirkwood_defconfig           |   22 ----
 arch/arm/mach-kirkwood/Kconfig                |  156 -------------------------
 arch/arm/mach-kirkwood/Makefile               |   23 +----
 arch/arm/mach-kirkwood/board-db88f628x-bp.c   |   24 ----
 arch/arm/mach-kirkwood/board-dnskw.c          |    7 -
 arch/arm/mach-kirkwood/board-dockstar.c       |   32 -----
 arch/arm/mach-kirkwood/board-dreamplug.c      |   35 ------
 arch/arm/mach-kirkwood/board-dt.c             |   84 +-------------
 arch/arm/mach-kirkwood/board-goflexnet.c      |   34 ------
 arch/arm/mach-kirkwood/board-guruplug.c       |   33 -----
 arch/arm/mach-kirkwood/board-ib62x0.c         |   29 -----
 arch/arm/mach-kirkwood/board-iconnect.c       |   24 ----
 arch/arm/mach-kirkwood/board-iomega_ix2_200.c |   34 ------
 arch/arm/mach-kirkwood/board-km_kirkwood.c    |   44 -------
 arch/arm/mach-kirkwood/board-lsxl.c           |   36 ------
 arch/arm/mach-kirkwood/board-mplcec4.c        |   35 ------
 arch/arm/mach-kirkwood/board-ns2.c            |   35 ------
 arch/arm/mach-kirkwood/board-openblocks_a6.c  |   26 ----
 arch/arm/mach-kirkwood/board-readynas.c       |   27 -----
 arch/arm/mach-kirkwood/board-sheevaplug.c     |   27 -----
 arch/arm/mach-kirkwood/board-ts219.c          |   40 -------
 arch/arm/mach-kirkwood/board-usi_topkick.c    |   29 -----
 22 files changed, 2 insertions(+), 834 deletions(-)
 delete mode 100644 arch/arm/mach-kirkwood/board-db88f628x-bp.c
 delete mode 100644 arch/arm/mach-kirkwood/board-dockstar.c
 delete mode 100644 arch/arm/mach-kirkwood/board-dreamplug.c
 delete mode 100644 arch/arm/mach-kirkwood/board-goflexnet.c
 delete mode 100644 arch/arm/mach-kirkwood/board-guruplug.c
 delete mode 100644 arch/arm/mach-kirkwood/board-ib62x0.c
 delete mode 100644 arch/arm/mach-kirkwood/board-iconnect.c
 delete mode 100644 arch/arm/mach-kirkwood/board-iomega_ix2_200.c
 delete mode 100644 arch/arm/mach-kirkwood/board-km_kirkwood.c
 delete mode 100644 arch/arm/mach-kirkwood/board-lsxl.c
 delete mode 100644 arch/arm/mach-kirkwood/board-mplcec4.c
 delete mode 100644 arch/arm/mach-kirkwood/board-ns2.c
 delete mode 100644 arch/arm/mach-kirkwood/board-openblocks_a6.c
 delete mode 100644 arch/arm/mach-kirkwood/board-readynas.c
 delete mode 100644 arch/arm/mach-kirkwood/board-sheevaplug.c
 delete mode 100644 arch/arm/mach-kirkwood/board-ts219.c
 delete mode 100644 arch/arm/mach-kirkwood/board-usi_topkick.c

diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
index 0f2aa61..3235808 100644
--- a/arch/arm/configs/kirkwood_defconfig
+++ b/arch/arm/configs/kirkwood_defconfig
@@ -29,29 +29,7 @@ CONFIG_MACH_SHEEVAPLUG=y
 CONFIG_MACH_T5325=y
 CONFIG_MACH_TS219=y
 CONFIG_MACH_TS41X=y
-CONFIG_MACH_CLOUDBOX_DT=y
-CONFIG_MACH_DB88F628X_BP_DT=y
 CONFIG_MACH_DLINK_KIRKWOOD_DT=y
-CONFIG_MACH_DOCKSTAR_DT=y
-CONFIG_MACH_DREAMPLUG_DT=y
-CONFIG_MACH_GOFLEXNET_DT=y
-CONFIG_MACH_GURUPLUG_DT=y
-CONFIG_MACH_IB62X0_DT=y
-CONFIG_MACH_ICONNECT_DT=y
-CONFIG_MACH_INETSPACE_V2_DT=y
-CONFIG_MACH_IOMEGA_IX2_200_DT=y
-CONFIG_MACH_KM_KIRKWOOD_DT=y
-CONFIG_MACH_LSXL_DT=y
-CONFIG_MACH_MPLCEC4_DT=y
-CONFIG_MACH_NETSPACE_LITE_V2_DT=y
-CONFIG_MACH_NETSPACE_MAX_V2_DT=y
-CONFIG_MACH_NETSPACE_MINI_V2_DT=y
-CONFIG_MACH_NETSPACE_V2_DT=y
-CONFIG_MACH_NSA310_DT=y
-CONFIG_MACH_OPENBLOCKS_A6_DT=y
-CONFIG_MACH_READYNAS_DT=y
-CONFIG_MACH_SHEEVAPLUG_DT=y
-CONFIG_MACH_TOPKICK_DT=y
 CONFIG_MACH_TS219_DT=y
 # CONFIG_CPU_FEROCEON_OLD_ID is not set
 CONFIG_PCI_MVEBU=y
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index b634f96..493c71a 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -139,20 +139,6 @@ config ARCH_KIRKWOOD_DT
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Kirkwood using flattened device tree.
 
-config MACH_CLOUDBOX_DT
-	bool "LaCie CloudBox NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  CloudBox NAS, using Flattened Device Tree.
-
-config MACH_DB88F628X_BP_DT
-	bool "Marvell DB-88F628x-BP Development Board (Flattened Device Tree)"
-	help
-	  Say 'Y' here if you want your kernel to support the Marvell
-	  DB-88F6281-BP and DB-88F6282-BP Development Board (Flattened
-	  Device Tree).
-
 config MACH_DLINK_KIRKWOOD_DT
 	bool "D-Link Kirkwood-based NAS (Flattened Device Tree)"
 	select ARCH_KIRKWOOD_DT
@@ -161,148 +147,6 @@ config MACH_DLINK_KIRKWOOD_DT
 	  Kirkwood-based D-Link NASes such as DNS-320 & DNS-325,
 	  using Flattened Device Tree.
 
-config MACH_DOCKSTAR_DT
-	bool "Seagate FreeAgent Dockstar (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Seagate FreeAgent Dockstar (Flattened Device Tree).
-
-config MACH_DREAMPLUG_DT
-	bool "Marvell DreamPlug (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell DreamPlug (Flattened Device Tree).
-
-config MACH_GOFLEXNET_DT
-	bool "Seagate GoFlex Net (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Seagate GoFlex Net (Flattened Device Tree).
-
-config MACH_GURUPLUG_DT
-	bool "Marvell GuruPlug Reference Board (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell GuruPlug Reference Board (Flattened Device Tree).
-
-config MACH_IB62X0_DT
-	bool "RaidSonic IB-NAS6210, IB-NAS6220 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  RaidSonic IB-NAS6210 & IB-NAS6220 devices, using
-	  Flattened Device Tree.
-
-config MACH_ICONNECT_DT
-	bool "Iomega Iconnect (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here to enable Iomega Iconnect support.
-
-config MACH_INETSPACE_V2_DT
-	bool "LaCie Internet Space v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Internet Space v2 NAS, using Flattened Device Tree.
-
-config MACH_IOMEGA_IX2_200_DT
-	bool "Iomega StorCenter ix2-200 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Iomega StorCenter ix2-200 (Flattened Device Tree).
-
-config MACH_KM_KIRKWOOD_DT
-	bool "Keymile Kirkwood Reference Design (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Keymile Kirkwood Reference Desgin, using Flattened Device Tree.
-
-config MACH_LSXL_DT
-	bool "Buffalo Linkstation LS-XHL, LS-CHLv2 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	select POWER_RESET_RESTART
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Buffalo Linkstation LS-XHL & LS-CHLv2 devices, using
-	  Flattened Device Tree.
-
-config MACH_MPLCEC4_DT
-	bool "MPL CEC4 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  MPL CEC4 (Flattened Device Tree).
-
-config MACH_NETSPACE_LITE_V2_DT
-	bool "LaCie Network Space Lite v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space Lite v2 NAS, using Flattened Device Tree.
-
-config MACH_NETSPACE_MAX_V2_DT
-	bool "LaCie Network Space Max v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space Max v2 NAS, using Flattened Device Tree.
-
-config MACH_NETSPACE_MINI_V2_DT
-	bool "LaCie Network Space Mini v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space Mini v2 NAS using Flattened Device Tree.
-
-	  This board is embedded in a product named CloudBox, which
-	  provides automatic backup on a 100GB cloud storage. This
-	  should not confused with a more recent LaCie NAS also named
-	  CloudBox. For this last, the disk capacity is 1TB or above.
-
-config MACH_NETSPACE_V2_DT
-	bool "LaCie Network Space v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space v2 NAS, using Flattened Device Tree.
-
-config MACH_OPENBLOCKS_A6_DT
-	bool "Plat'Home OpenBlocks A6 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Plat'Home OpenBlocks A6 (Flattened Device Tree).
-
-config MACH_READYNAS_DT
-	bool "NETGEAR ReadyNAS Duo v2 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	select ARM_APPENDED_DTB
-	select ARM_ATAG_DTB_COMPAT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  NETGEAR ReadyNAS Duo v2 using Fattened Device Tree.
-
-config MACH_SHEEVAPLUG_DT
-	bool "Marvell (eSATA) SheevaPlug (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell (eSATA) SheevaPlug (Flattened Device Tree).
-
-config MACH_TOPKICK_DT
-	bool "USI Topkick (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  USI Topkick, using Flattened Device Tree
-
 config MACH_TS219_DT
 	bool "Device Tree for QNAP TS-11X, TS-21X NAS"
 	select ARCH_KIRKWOOD_DT
diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
index ac4cd75..062f8c7 100644
--- a/arch/arm/mach-kirkwood/Makefile
+++ b/arch/arm/mach-kirkwood/Makefile
@@ -19,26 +19,5 @@ obj-$(CONFIG_MACH_TS219)		+= ts219-setup.o tsx1x-common.o
 obj-$(CONFIG_MACH_TS41X)		+= ts41x-setup.o tsx1x-common.o
 
 obj-$(CONFIG_ARCH_KIRKWOOD_DT)		+= board-dt.o
-obj-$(CONFIG_MACH_CLOUDBOX_DT)		+= board-ns2.o
-obj-$(CONFIG_MACH_DB88F628X_BP_DT)	+= board-db88f628x-bp.o
 obj-$(CONFIG_MACH_DLINK_KIRKWOOD_DT)	+= board-dnskw.o
-obj-$(CONFIG_MACH_DOCKSTAR_DT)		+= board-dockstar.o
-obj-$(CONFIG_MACH_DREAMPLUG_DT)		+= board-dreamplug.o
-obj-$(CONFIG_MACH_GOFLEXNET_DT)		+= board-goflexnet.o
-obj-$(CONFIG_MACH_GURUPLUG_DT)		+= board-guruplug.o
-obj-$(CONFIG_MACH_IB62X0_DT)		+= board-ib62x0.o
-obj-$(CONFIG_MACH_ICONNECT_DT)		+= board-iconnect.o
-obj-$(CONFIG_MACH_INETSPACE_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_IOMEGA_IX2_200_DT)	+= board-iomega_ix2_200.o
-obj-$(CONFIG_MACH_KM_KIRKWOOD_DT)	+= board-km_kirkwood.o
-obj-$(CONFIG_MACH_LSXL_DT)		+= board-lsxl.o
-obj-$(CONFIG_MACH_MPLCEC4_DT)		+= board-mplcec4.o
-obj-$(CONFIG_MACH_NETSPACE_LITE_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_NETSPACE_MAX_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_NETSPACE_MINI_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_NETSPACE_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_OPENBLOCKS_A6_DT)	+= board-openblocks_a6.o
-obj-$(CONFIG_MACH_READYNAS_DT)		+= board-readynas.o
-obj-$(CONFIG_MACH_SHEEVAPLUG_DT)	+= board-sheevaplug.o
-obj-$(CONFIG_MACH_TOPKICK_DT)		+= board-usi_topkick.o
-obj-$(CONFIG_MACH_TS219_DT)		+= board-ts219.o tsx1x-common.o
+obj-$(CONFIG_MACH_TS219_DT)		+= tsx1x-common.o
diff --git a/arch/arm/mach-kirkwood/board-db88f628x-bp.c b/arch/arm/mach-kirkwood/board-db88f628x-bp.c
deleted file mode 100644
index 2f574bc..0000000
--- a/arch/arm/mach-kirkwood/board-db88f628x-bp.c
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * Saeed Bishara <saeed@marvell.com>
- *
- * Marvell DB-88F628{1,2}-BP Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/of.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data db88f628x_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init db88f628x_init(void)
-{
-	kirkwood_ge00_init(&db88f628x_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-dnskw.c b/arch/arm/mach-kirkwood/board-dnskw.c
index a1aa87f..2af7a95 100644
--- a/arch/arm/mach-kirkwood/board-dnskw.c
+++ b/arch/arm/mach-kirkwood/board-dnskw.c
@@ -14,14 +14,9 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
 #include <linux/gpio.h>
 #include "common.h"
 
-static struct mv643xx_eth_platform_data dnskw_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
 /* Register any GPIO for output and set the value */
 static void __init dnskw_gpio_register(unsigned gpio, char *name, int def)
 {
@@ -36,8 +31,6 @@ static void __init dnskw_gpio_register(unsigned gpio, char *name, int def)
 
 void __init dnskw_init(void)
 {
-	kirkwood_ge00_init(&dnskw_ge00_data);
-
 	/* Set NAS to turn back on after a power failure */
 	dnskw_gpio_register(37, "dnskw:power:recover", 1);
 }
diff --git a/arch/arm/mach-kirkwood/board-dockstar.c b/arch/arm/mach-kirkwood/board-dockstar.c
deleted file mode 100644
index d7196db..0000000
--- a/arch/arm/mach-kirkwood/board-dockstar.c
+++ /dev/null
@@ -1,32 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-dockstar.c
- *
- * Seagate FreeAgent Dockstar Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
- * Copied and modified for Seagate GoFlex Net support by
- * Joshua Coombs <josh.coombs@gmail.com> based on ArchLinux ARM's
- * GoFlex kernel patches.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data dockstar_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init dockstar_dt_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&dockstar_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-dreamplug.c b/arch/arm/mach-kirkwood/board-dreamplug.c
deleted file mode 100644
index 0903242..0000000
--- a/arch/arm/mach-kirkwood/board-dreamplug.c
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
- *
- * arch/arm/mach-kirkwood/board-dreamplug.c
- *
- * Marvell DreamPlug Reference Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data dreamplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data dreamplug_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-void __init dreamplug_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&dreamplug_ge00_data);
-	kirkwood_ge01_init(&dreamplug_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
index 6e122ed..a3271f6 100644
--- a/arch/arm/mach-kirkwood/board-dt.c
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -102,96 +102,14 @@ static void __init kirkwood_dt_init(void)
 	kexec_reinit = kirkwood_enable_pcie;
 #endif
 
-	if (of_machine_is_compatible("globalscale,dreamplug"))
-		dreamplug_init();
-
-	if (of_machine_is_compatible("globalscale,guruplug"))
-		guruplug_dt_init();
-
-	if (of_machine_is_compatible("globalscale,sheevaplug"))
-		sheevaplug_dt_init();
-
 	if (of_machine_is_compatible("dlink,dns-kirkwood"))
 		dnskw_init();
 
-	if (of_machine_is_compatible("iom,iconnect"))
-		iconnect_init();
-
-	if (of_machine_is_compatible("raidsonic,ib-nas62x0"))
-		ib62x0_init();
-
-	if (of_machine_is_compatible("qnap,ts219"))
-		qnap_dt_ts219_init();
-
-	if (of_machine_is_compatible("seagate,dockstar"))
-		dockstar_dt_init();
-
-	if (of_machine_is_compatible("seagate,goflexnet"))
-		goflexnet_init();
-
-	if (of_machine_is_compatible("buffalo,lsxl"))
-		lsxl_init();
-
-	if (of_machine_is_compatible("iom,ix2-200"))
-		iomega_ix2_200_init();
-
-	if (of_machine_is_compatible("keymile,km_kirkwood"))
-		km_kirkwood_init();
-
-	if (of_machine_is_compatible("lacie,cloudbox") ||
-	    of_machine_is_compatible("lacie,inetspace_v2") ||
-	    of_machine_is_compatible("lacie,netspace_lite_v2") ||
-	    of_machine_is_compatible("lacie,netspace_max_v2") ||
-	    of_machine_is_compatible("lacie,netspace_mini_v2") ||
-	    of_machine_is_compatible("lacie,netspace_v2"))
-		ns2_init();
-
-	if (of_machine_is_compatible("marvell,db-88f6281-bp") ||
-	    of_machine_is_compatible("marvell,db-88f6282-bp"))
-		db88f628x_init();
-
-	if (of_machine_is_compatible("mpl,cec4"))
-		mplcec4_init();
-
-	if (of_machine_is_compatible("netgear,readynas-duo-v2"))
-		netgear_readynas_init();
-
-	if (of_machine_is_compatible("plathome,openblocks-a6"))
-		openblocks_a6_init();
-
-	if (of_machine_is_compatible("usi,topkick"))
-		usi_topkick_init();
-
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 
 static const char * const kirkwood_dt_board_compat[] = {
-	"globalscale,dreamplug",
-	"globalscale,guruplug",
-	"globalscale,sheevaplug",
-	"dlink,dns-320",
-	"dlink,dns-325",
-	"iom,iconnect",
-	"raidsonic,ib-nas62x0",
-	"qnap,ts219",
-	"seagate,dockstar",
-	"seagate,goflexnet",
-	"buffalo,lsxl",
-	"iom,ix2-200",
-	"keymile,km_kirkwood",
-	"lacie,cloudbox",
-	"lacie,inetspace_v2",
-	"lacie,netspace_lite_v2",
-	"lacie,netspace_max_v2",
-	"lacie,netspace_mini_v2",
-	"lacie,netspace_v2",
-	"marvell,db-88f6281-bp",
-	"marvell,db-88f6282-bp",
-	"mpl,cec4",
-	"netgear,readynas-duo-v2",
-	"plathome,openblocks-a6",
-	"usi,topkick",
-	"zyxel,nsa310",
+	"marvell,kirkwood",
 	NULL
 };
 
diff --git a/arch/arm/mach-kirkwood/board-goflexnet.c b/arch/arm/mach-kirkwood/board-goflexnet.c
deleted file mode 100644
index 9db979a..0000000
--- a/arch/arm/mach-kirkwood/board-goflexnet.c
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
- *
- * arch/arm/mach-kirkwood/board-goflexnet.c
- *
- * Seagate GoFlext Net Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
- * Copied and modified for Seagate GoFlex Net support by
- * Joshua Coombs <josh.coombs@gmail.com> based on ArchLinux ARM's
- * GoFlex kernel patches.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data goflexnet_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init goflexnet_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&goflexnet_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-guruplug.c b/arch/arm/mach-kirkwood/board-guruplug.c
deleted file mode 100644
index a857163..0000000
--- a/arch/arm/mach-kirkwood/board-guruplug.c
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-guruplug.c
- *
- * Marvell Guruplug Reference Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data guruplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data guruplug_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-void __init guruplug_dt_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&guruplug_ge00_data);
-	kirkwood_ge01_init(&guruplug_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-ib62x0.c b/arch/arm/mach-kirkwood/board-ib62x0.c
deleted file mode 100644
index 9a857ae..0000000
--- a/arch/arm/mach-kirkwood/board-ib62x0.c
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- * Copyright 2012 (C), Simon Baatz <gmbnomis@gmail.com>
- *
- * arch/arm/mach-kirkwood/board-ib62x0.c
- *
- * RaidSonic ICY BOX IB-NAS6210 & IB-NAS6220 init for drivers not
- * converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data ib62x0_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init ib62x0_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&ib62x0_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-iconnect.c b/arch/arm/mach-kirkwood/board-iconnect.c
deleted file mode 100644
index 98b5ad1..0000000
--- a/arch/arm/mach-kirkwood/board-iconnect.c
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-iconnect.c
- *
- * Iomega i-connect Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/of.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data iconnect_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(11),
-};
-
-void __init iconnect_init(void)
-{
-	kirkwood_ge00_init(&iconnect_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
deleted file mode 100644
index e5f7041..0000000
--- a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-iomega_ix2_200.c
- *
- * Iomega StorCenter ix2-200
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/ethtool.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = {
-	.phy_addr       = MV643XX_ETH_PHY_NONE,
-	.speed          = SPEED_1000,
-	.duplex         = DUPLEX_FULL,
-};
-
-static struct mv643xx_eth_platform_data iomega_ix2_200_ge01_data = {
-        .phy_addr       = MV643XX_ETH_PHY_ADDR(11),
-};
-
-void __init iomega_ix2_200_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&iomega_ix2_200_ge00_data);
-	kirkwood_ge01_init(&iomega_ix2_200_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-km_kirkwood.c b/arch/arm/mach-kirkwood/board-km_kirkwood.c
deleted file mode 100644
index 44e4605..0000000
--- a/arch/arm/mach-kirkwood/board-km_kirkwood.c
+++ /dev/null
@@ -1,44 +0,0 @@
-/*
- * Copyright 2012 2012 KEYMILE AG, CH-3097 Bern
- * Valentin Longchamp <valentin.longchamp@keymile.com>
- *
- * arch/arm/mach-kirkwood/board-km_kirkwood.c
- *
- * Keymile km_kirkwood Reference Desing Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/clk.h>
-#include <linux/clk-private.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data km_kirkwood_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init km_kirkwood_init(void)
-{
-	struct clk *sata_clk;
-	/*
-	 * Our variant of kirkwood (integrated in the Bobcat) hangs on accessing
-	 * SATA bits (14-15) of the Clock Gating Control Register. Since these
-	 * devices are also not present in this variant, their clocks get
-	 * disabled because unused when clk_disable_unused() gets called.
-	 * That's why we change the flags to these clocks to CLK_IGNORE_UNUSED
-	 */
-	sata_clk = clk_get_sys("sata_mv.0", "0");
-	if (!IS_ERR(sata_clk))
-		sata_clk->flags |= CLK_IGNORE_UNUSED;
-	sata_clk = clk_get_sys("sata_mv.0", "1");
-	if (!IS_ERR(sata_clk))
-		sata_clk->flags |= CLK_IGNORE_UNUSED;
-
-	kirkwood_ge00_init(&km_kirkwood_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-lsxl.c b/arch/arm/mach-kirkwood/board-lsxl.c
deleted file mode 100644
index 3483952..0000000
--- a/arch/arm/mach-kirkwood/board-lsxl.c
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * Copyright 2012 (C), Michael Walle <michael@walle.cc>
- *
- * arch/arm/mach-kirkwood/board-lsxl.c
- *
- * Buffalo Linkstation LS-XHL and LS-CHLv2 init for drivers not
- * converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data lsxl_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data lsxl_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init lsxl_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-
-	kirkwood_ge00_init(&lsxl_ge00_data);
-	kirkwood_ge01_init(&lsxl_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-mplcec4.c b/arch/arm/mach-kirkwood/board-mplcec4.c
deleted file mode 100644
index 938712e..0000000
--- a/arch/arm/mach-kirkwood/board-mplcec4.c
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * Copyright (C) 2012 MPL AG, Switzerland
- * Stefan Peter <s.peter@mpl.ch>
- *
- * arch/arm/mach-kirkwood/board-mplcec4.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data mplcec4_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-static struct mv643xx_eth_platform_data mplcec4_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(2),
-};
-
-void __init mplcec4_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&mplcec4_ge00_data);
-	kirkwood_ge01_init(&mplcec4_ge01_data);
-}
-
-
-
diff --git a/arch/arm/mach-kirkwood/board-ns2.c b/arch/arm/mach-kirkwood/board-ns2.c
deleted file mode 100644
index f8f6605..0000000
--- a/arch/arm/mach-kirkwood/board-ns2.c
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * Copyright 2012 (C), Simon Guinot <simon.guinot@sequanux.org>
- *
- * arch/arm/mach-kirkwood/board-ns2.c
- *
- * LaCie Network Space v2 board (and parents) initialization for drivers
- * not converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/of.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data ns2_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init ns2_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	if (of_machine_is_compatible("lacie,cloudbox") ||
-	    of_machine_is_compatible("lacie,netspace_lite_v2") ||
-	    of_machine_is_compatible("lacie,netspace_mini_v2"))
-		ns2_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
-	kirkwood_ge00_init(&ns2_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-openblocks_a6.c b/arch/arm/mach-kirkwood/board-openblocks_a6.c
deleted file mode 100644
index b11d8fd..0000000
--- a/arch/arm/mach-kirkwood/board-openblocks_a6.c
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * Copyright 2012 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- *
- * arch/arm/mach-kirkwood/board-openblocks_a6.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data openblocks_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init openblocks_a6_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&openblocks_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-readynas.c b/arch/arm/mach-kirkwood/board-readynas.c
deleted file mode 100644
index 341b82d..0000000
--- a/arch/arm/mach-kirkwood/board-readynas.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * NETGEAR ReadyNAS Duo v2 Board setup for drivers not already
- * converted to DT.
- *
- * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data netgear_readynas_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init netgear_readynas_init(void)
-{
-	kirkwood_ge00_init(&netgear_readynas_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-sheevaplug.c b/arch/arm/mach-kirkwood/board-sheevaplug.c
deleted file mode 100644
index fa38937..0000000
--- a/arch/arm/mach-kirkwood/board-sheevaplug.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-sheevaplug.c
- *
- * Marvell Sheevaplug Reference Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data sheevaplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init sheevaplug_dt_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&sheevaplug_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-ts219.c b/arch/arm/mach-kirkwood/board-ts219.c
deleted file mode 100644
index 860f44a..0000000
--- a/arch/arm/mach-kirkwood/board-ts219.c
+++ /dev/null
@@ -1,40 +0,0 @@
-/*
- *
- * QNAP TS-11x/TS-21x Turbo NAS Board Setup via DT
- *
- * Copyright (C) 2012 Andrew Lunn <andrew@lunn.ch>
- *
- * Based on the board file ts219-setup.c:
- *
- * Copyright (C) 2009  Martin Michlmayr <tbm@cyrius.com>
- * Copyright (C) 2008  Byron Bradley <byron.bbradley@gmail.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data qnap_ts219_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init qnap_dt_ts219_init(void)
-{
-	u32 dev, rev;
-
-	kirkwood_pcie_id(&dev, &rev);
-	if (dev == MV88F6282_DEV_ID)
-		qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
-
-	kirkwood_ge00_init(&qnap_ts219_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-usi_topkick.c b/arch/arm/mach-kirkwood/board-usi_topkick.c
deleted file mode 100644
index 1cc04ec..0000000
--- a/arch/arm/mach-kirkwood/board-usi_topkick.c
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
- *
- * arch/arm/mach-kirkwood/board-usi_topkick.c
- *
- * USI Topkick Init for drivers not converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data topkick_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init usi_topkick_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&topkick_ge00_data);
-}
-- 
1.7.2.5

[PATCH v6 6/7] ARM: kirkwood: remove legacy clk alias for mv643xx_eth

[Sebastian Hesselbarth]

With all boards converted to DT enabled mv643xx_eth we can now
remove the clock alias for gbe clocks.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Changelog:
v5->v6:
- rebase for v3.11-rc1

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
---
 arch/arm/mach-kirkwood/board-dt.c |    2 --
 1 files changed, 0 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
index a3271f6..881f37e 100644
--- a/arch/arm/mach-kirkwood/board-dt.c
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -60,12 +60,10 @@ static void __init kirkwood_legacy_clk_init(void)
 	 */
 	clkspec.args[0] = CGC_BIT_GE0;
 	clk = of_clk_get_from_provider(&clkspec);
-	orion_clkdev_add(NULL, "mv643xx_eth_port.0", clk);
 	clk_prepare_enable(clk);
 
 	clkspec.args[0] = CGC_BIT_GE1;
 	clk = of_clk_get_from_provider(&clkspec);
-	orion_clkdev_add(NULL, "mv643xx_eth_port.1", clk);
 	clk_prepare_enable(clk);
 }
 
-- 
1.7.2.5

[PATCH v6 7/7] ARM: orion5x: remove legacy mv643xx_eth board setup

[Sebastian Hesselbarth]

With DT support for mv643xx_eth we do not need legacy platform_data
based setup for DT enabled boards. This patch removes eth setup
for all orion5x DT board files.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Changelog:
v5->v6:
- rebase for v3.11-rc1

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
---
 arch/arm/mach-orion5x/edmini_v2-setup.c |   10 ----------
 1 files changed, 0 insertions(+), 10 deletions(-)

diff --git a/arch/arm/mach-orion5x/edmini_v2-setup.c b/arch/arm/mach-orion5x/edmini_v2-setup.c
index 1cecedc..7d316ed 100644
--- a/arch/arm/mach-orion5x/edmini_v2-setup.c
+++ b/arch/arm/mach-orion5x/edmini_v2-setup.c
@@ -25,7 +25,6 @@
 #include <linux/irq.h>
 #include <linux/mbus.h>
 #include <linux/mtd/physmap.h>
-#include <linux/mv643xx_eth.h>
 #include <linux/leds.h>
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
@@ -97,14 +96,6 @@ static struct platform_device edmini_v2_nor_flash = {
 };
 
 /*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data edmini_v2_eth_data = {
-	.phy_addr	= 8,
-};
-
-/*****************************************************************************
  * RTC 5C372a on I2C bus
  ****************************************************************************/
 
@@ -153,7 +144,6 @@ void __init edmini_v2_init(void)
 	 * Configure peripherals.
 	 */
 	orion5x_ehci0_init();
-	orion5x_eth_init(&edmini_v2_eth_data);
 
 	mvebu_mbus_add_window("devbus-boot", EDMINI_V2_NOR_BOOT_BASE,
 			      EDMINI_V2_NOR_BOOT_SIZE);
-- 
1.7.2.5

Re: [PATCH v6 5/7] ARM: kirkwood: remove redundant DT board files

[Arnaud Ebalard]

Hi Sebastian,

Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> writes:

> With DT support for mv643xx_eth board specific init for some boards now
> is unneccessary. Remove those board files, Kconfig entries, and
> corresponding entries in kirkwood_defconfig.

Applying above your set an old quilt cleaning patch Jason asked at some
point, it became empty except for arch/arm/mach_kirkwood/common.h in
which some declarations were left behind. If this is correct, can you
just merge the hunks below in your 5/7 in next round?

AFAICT, only dnskw_init() remains, which matches the list of board-*.c
files in arch/arm/mach_kirkwood/ (i.e. board-dt.c and board-dnskw.c).

Cheers,

a+

Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
---
 arch/arm/mach-kirkwood/common.h | 108 ----------------------------------------
 1 file changed, 108 deletions(-)

diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
index 1c09f3f..1cbdd2b 100644
--- a/arch/arm/mach-kirkwood/common.h
+++ b/arch/arm/mach-kirkwood/common.h
@@ -57,26 +57,6 @@ void kirkwood_restart(char, const char *);
 void kirkwood_clk_init(void);
 
 /* board init functions for boards not fully converted to fdt */
-#ifdef CONFIG_MACH_DREAMPLUG_DT
-void dreamplug_init(void);
-#else
-static inline void dreamplug_init(void) {};
-#endif
-#ifdef CONFIG_MACH_GURUPLUG_DT
-void guruplug_dt_init(void);
-#else
-static inline void guruplug_dt_init(void) {};
-#endif
-#ifdef CONFIG_MACH_SHEEVAPLUG_DT
-void sheevaplug_dt_init(void);
-#else
-static inline void sheevaplug_dt_init(void) {};
-#endif
-#ifdef CONFIG_MACH_TS219_DT
-void qnap_dt_ts219_init(void);
-#else
-static inline void qnap_dt_ts219_init(void) {};
-#endif
 
 #ifdef CONFIG_MACH_DLINK_KIRKWOOD_DT
 void dnskw_init(void);
@@ -84,94 +64,6 @@ void dnskw_init(void);
 static inline void dnskw_init(void) {};
 #endif
 
-#ifdef CONFIG_MACH_ICONNECT_DT
-void iconnect_init(void);
-#else
-static inline void iconnect_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_IB62X0_DT
-void ib62x0_init(void);
-#else
-static inline void ib62x0_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_DOCKSTAR_DT
-void dockstar_dt_init(void);
-#else
-static inline void dockstar_dt_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_GOFLEXNET_DT
-void goflexnet_init(void);
-#else
-static inline void goflexnet_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_LSXL_DT
-void lsxl_init(void);
-#else
-static inline void lsxl_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_IOMEGA_IX2_200_DT
-void iomega_ix2_200_init(void);
-#else
-static inline void iomega_ix2_200_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_KM_KIRKWOOD_DT
-void km_kirkwood_init(void);
-#else
-static inline void km_kirkwood_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_DB88F628X_BP_DT
-void db88f628x_init(void);
-#else
-static inline void db88f628x_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_MPLCEC4_DT
-void mplcec4_init(void);
-#else
-static inline void mplcec4_init(void) {};
-#endif
-
-#if defined(CONFIG_MACH_INETSPACE_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_MAX_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_LITE_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_MINI_V2_DT)
-void ns2_init(void);
-#else
-static inline void ns2_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_OPENBLOCKS_A6_DT
-void openblocks_a6_init(void);
-#else
-static inline void openblocks_a6_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_READYNAS_DT
-void netgear_readynas_init(void);
-#else
-static inline void netgear_readynas_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_TOPKICK_DT
-void usi_topkick_init(void);
-#else
-static inline void usi_topkick_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_CLOUDBOX_DT
-void cloudbox_init(void);
-#else
-static inline void cloudbox_init(void) {};
-#endif
-
 /* early init functions not converted to fdt yet */
 char *kirkwood_id(void);
 void kirkwood_l2_init(void);
-- 
1.8.3.1

Re: [PATCH v6 5/7] ARM: kirkwood: remove redundant DT board files

[Sebastian Hesselbarth]

On 07/03/2013 01:09 AM, Arnaud Ebalard wrote:
> Hi Sebastian,
>
> Sebastian Hesselbarth<sebastian.hesselbarth@gmail.com>  writes:
>
>> With DT support for mv643xx_eth board specific init for some boards now
>> is unneccessary. Remove those board files, Kconfig entries, and
>> corresponding entries in kirkwood_defconfig.
>
> Applying above your set an old quilt cleaning patch Jason asked at some
> point, it became empty except for arch/arm/mach_kirkwood/common.h in
> which some declarations were left behind. If this is correct, can you
> just merge the hunks below in your 5/7 in next round?
>
> AFAICT, only dnskw_init() remains, which matches the list of board-*.c
> files in arch/arm/mach_kirkwood/ (i.e. board-dt.c and board-dnskw.c).

Arnaud,

thanks for sending this! I will squash it into v6 and send a v7 of this
patch. Looks like ARM SoC pull request causes some issues with Russell's
tree, so there is plenty of time left to resend (and re-test :))

And you are right, only board-dt.c and board-dnskw.c remain in
mach-kirkwood. With irqchip/clocksource patches in, IMHO kirkwood is
quite ready for mach-mvebu. mach-dove is still missing DT pcie, and I 
haven't had any success to get my hands on a board with pcie to test,
yet.

Sebastian

> Signed-off-by: Arnaud Ebalard<arno@natisbad.org>
> ---
>   arch/arm/mach-kirkwood/common.h | 108 ----------------------------------------
>   1 file changed, 108 deletions(-)
>
> diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
> index 1c09f3f..1cbdd2b 100644
> --- a/arch/arm/mach-kirkwood/common.h
> +++ b/arch/arm/mach-kirkwood/common.h
> @@ -57,26 +57,6 @@ void kirkwood_restart(char, const char *);
>   void kirkwood_clk_init(void);
>
>   /* board init functions for boards not fully converted to fdt */
> -#ifdef CONFIG_MACH_DREAMPLUG_DT
> -void dreamplug_init(void);
> -#else
> -static inline void dreamplug_init(void) {};
> -#endif
> -#ifdef CONFIG_MACH_GURUPLUG_DT
> -void guruplug_dt_init(void);
> -#else
> -static inline void guruplug_dt_init(void) {};
> -#endif
> -#ifdef CONFIG_MACH_SHEEVAPLUG_DT
> -void sheevaplug_dt_init(void);
> -#else
> -static inline void sheevaplug_dt_init(void) {};
> -#endif
> -#ifdef CONFIG_MACH_TS219_DT
> -void qnap_dt_ts219_init(void);
> -#else
> -static inline void qnap_dt_ts219_init(void) {};
> -#endif
>
>   #ifdef CONFIG_MACH_DLINK_KIRKWOOD_DT
>   void dnskw_init(void);
> @@ -84,94 +64,6 @@ void dnskw_init(void);
>   static inline void dnskw_init(void) {};
>   #endif
>
> -#ifdef CONFIG_MACH_ICONNECT_DT
> -void iconnect_init(void);
> -#else
> -static inline void iconnect_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_IB62X0_DT
> -void ib62x0_init(void);
> -#else
> -static inline void ib62x0_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_DOCKSTAR_DT
> -void dockstar_dt_init(void);
> -#else
> -static inline void dockstar_dt_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_GOFLEXNET_DT
> -void goflexnet_init(void);
> -#else
> -static inline void goflexnet_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_LSXL_DT
> -void lsxl_init(void);
> -#else
> -static inline void lsxl_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_IOMEGA_IX2_200_DT
> -void iomega_ix2_200_init(void);
> -#else
> -static inline void iomega_ix2_200_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_KM_KIRKWOOD_DT
> -void km_kirkwood_init(void);
> -#else
> -static inline void km_kirkwood_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_DB88F628X_BP_DT
> -void db88f628x_init(void);
> -#else
> -static inline void db88f628x_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_MPLCEC4_DT
> -void mplcec4_init(void);
> -#else
> -static inline void mplcec4_init(void) {};
> -#endif
> -
> -#if defined(CONFIG_MACH_INETSPACE_V2_DT) || \
> -	defined(CONFIG_MACH_NETSPACE_V2_DT) || \
> -	defined(CONFIG_MACH_NETSPACE_MAX_V2_DT) || \
> -	defined(CONFIG_MACH_NETSPACE_LITE_V2_DT) || \
> -	defined(CONFIG_MACH_NETSPACE_MINI_V2_DT)
> -void ns2_init(void);
> -#else
> -static inline void ns2_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_OPENBLOCKS_A6_DT
> -void openblocks_a6_init(void);
> -#else
> -static inline void openblocks_a6_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_READYNAS_DT
> -void netgear_readynas_init(void);
> -#else
> -static inline void netgear_readynas_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_TOPKICK_DT
> -void usi_topkick_init(void);
> -#else
> -static inline void usi_topkick_init(void) {};
> -#endif
> -
> -#ifdef CONFIG_MACH_CLOUDBOX_DT
> -void cloudbox_init(void);
> -#else
> -static inline void cloudbox_init(void) {};
> -#endif
> -
>   /* early init functions not converted to fdt yet */
>   char *kirkwood_id(void);
>   void kirkwood_l2_init(void);

Re: [PATCH v6 5/7] ARM: kirkwood: remove redundant DT board files

[Sebastian Hesselbarth]

On 07/03/13 01:09, Arnaud Ebalard wrote:
> Hi Sebastian,
>
> Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> writes:
>
>> With DT support for mv643xx_eth board specific init for some boards now
>> is unneccessary. Remove those board files, Kconfig entries, and
>> corresponding entries in kirkwood_defconfig.
>
> Applying above your set an old quilt cleaning patch Jason asked at some
> point, it became empty except for arch/arm/mach_kirkwood/common.h in
> which some declarations were left behind. If this is correct, can you
> just merge the hunks below in your 5/7 in next round?
>
> AFAICT, only dnskw_init() remains, which matches the list of board-*.c
> files in arch/arm/mach_kirkwood/ (i.e. board-dt.c and board-dnskw.c).

While updating the patch with yours, I stumbled upon MACH_TS219_DT that
also remains because it includes tsx1x-common.c.

I cannot recall if Jason or Andrew said something about removing it..

Sebastian

Re: [PATCH v6 5/7] ARM: kirkwood: remove redundant DT board files

[Jason Cooper]

On Wed, Jul 03, 2013 at 01:31:47PM +0200, Sebastian Hesselbarth wrote:
> On 07/03/13 01:09, Arnaud Ebalard wrote:
> >Hi Sebastian,
> >
> >Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> writes:
> >
> >>With DT support for mv643xx_eth board specific init for some boards now
> >>is unneccessary. Remove those board files, Kconfig entries, and
> >>corresponding entries in kirkwood_defconfig.
> >
> >Applying above your set an old quilt cleaning patch Jason asked at some
> >point, it became empty except for arch/arm/mach_kirkwood/common.h in
> >which some declarations were left behind. If this is correct, can you
> >just merge the hunks below in your 5/7 in next round?
> >
> >AFAICT, only dnskw_init() remains, which matches the list of board-*.c
> >files in arch/arm/mach_kirkwood/ (i.e. board-dt.c and board-dnskw.c).
> 
> While updating the patch with yours, I stumbled upon MACH_TS219_DT that
> also remains because it includes tsx1x-common.c.
> 
> I cannot recall if Jason or Andrew said something about removing it..

board-ts219.c can be removed as well.  It needed a check for running on
the 6282 variant in order to set the phy address properly.  This can now
be handled in kirkwood-ts219-628[12].dts.

thx,

Jason.

Re: [PATCH v6 5/7] ARM: kirkwood: remove redundant DT board files

[Jason Cooper]

On Wed, Jul 03, 2013 at 01:31:47PM +0200, Sebastian Hesselbarth wrote:
> On 07/03/13 01:09, Arnaud Ebalard wrote:
> >Hi Sebastian,
> >
> >Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> writes:
> >
> >>With DT support for mv643xx_eth board specific init for some boards now
> >>is unneccessary. Remove those board files, Kconfig entries, and
> >>corresponding entries in kirkwood_defconfig.
> >
> >Applying above your set an old quilt cleaning patch Jason asked at some
> >point, it became empty except for arch/arm/mach_kirkwood/common.h in
> >which some declarations were left behind. If this is correct, can you
> >just merge the hunks below in your 5/7 in next round?
> >
> >AFAICT, only dnskw_init() remains, which matches the list of board-*.c
> >files in arch/arm/mach_kirkwood/ (i.e. board-dt.c and board-dnskw.c).
> 
> While updating the patch with yours, I stumbled upon MACH_TS219_DT that
> also remains because it includes tsx1x-common.c.

Oh yeah, that line can be removed as well.  It was originally included
for qnap_tsx1x_power_off().  This was replaced by

  e8fc721 power/reset: Add a new driver to turn QNAP board power off

thx,

Jason.

[PATCH v7 5/7] ARM: kirkwood: remove redundant DT board files

[Sebastian Hesselbarth]

With DT support for mv643xx_eth board specific init for some boards now
is unneccessary. Remove those board files, Kconfig entries, and
corresponding entries in kirkwood_defconfig.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Changelog:
v6->v7:
- cleanup mach-kirkwood/common.h (Reported by Arnaud Ebalard)
- also remove MACH_TS219_DT (Suggested by Jason Cooper)

v5->v6:
- rebase for v3.11-rc1

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
---
 arch/arm/configs/kirkwood_defconfig           |   23 ----
 arch/arm/mach-kirkwood/Kconfig                |  171 -------------------------
 arch/arm/mach-kirkwood/Makefile               |   22 ---
 arch/arm/mach-kirkwood/board-db88f628x-bp.c   |   24 ----
 arch/arm/mach-kirkwood/board-dnskw.c          |    7 -
 arch/arm/mach-kirkwood/board-dockstar.c       |   32 -----
 arch/arm/mach-kirkwood/board-dreamplug.c      |   35 -----
 arch/arm/mach-kirkwood/board-dt.c             |   84 +------------
 arch/arm/mach-kirkwood/board-goflexnet.c      |   34 -----
 arch/arm/mach-kirkwood/board-guruplug.c       |   33 -----
 arch/arm/mach-kirkwood/board-ib62x0.c         |   29 ----
 arch/arm/mach-kirkwood/board-iconnect.c       |   24 ----
 arch/arm/mach-kirkwood/board-iomega_ix2_200.c |   34 -----
 arch/arm/mach-kirkwood/board-km_kirkwood.c    |   44 -------
 arch/arm/mach-kirkwood/board-lsxl.c           |   36 -----
 arch/arm/mach-kirkwood/board-mplcec4.c        |   35 -----
 arch/arm/mach-kirkwood/board-ns2.c            |   35 -----
 arch/arm/mach-kirkwood/board-openblocks_a6.c  |   26 ----
 arch/arm/mach-kirkwood/board-readynas.c       |   27 ----
 arch/arm/mach-kirkwood/board-sheevaplug.c     |   27 ----
 arch/arm/mach-kirkwood/board-ts219.c          |   40 ------
 arch/arm/mach-kirkwood/board-usi_topkick.c    |   29 ----
 arch/arm/mach-kirkwood/common.h               |  109 ----------------
 23 files changed, 1 insertions(+), 959 deletions(-)
 delete mode 100644 arch/arm/mach-kirkwood/board-db88f628x-bp.c
 delete mode 100644 arch/arm/mach-kirkwood/board-dockstar.c
 delete mode 100644 arch/arm/mach-kirkwood/board-dreamplug.c
 delete mode 100644 arch/arm/mach-kirkwood/board-goflexnet.c
 delete mode 100644 arch/arm/mach-kirkwood/board-guruplug.c
 delete mode 100644 arch/arm/mach-kirkwood/board-ib62x0.c
 delete mode 100644 arch/arm/mach-kirkwood/board-iconnect.c
 delete mode 100644 arch/arm/mach-kirkwood/board-iomega_ix2_200.c
 delete mode 100644 arch/arm/mach-kirkwood/board-km_kirkwood.c
 delete mode 100644 arch/arm/mach-kirkwood/board-lsxl.c
 delete mode 100644 arch/arm/mach-kirkwood/board-mplcec4.c
 delete mode 100644 arch/arm/mach-kirkwood/board-ns2.c
 delete mode 100644 arch/arm/mach-kirkwood/board-openblocks_a6.c
 delete mode 100644 arch/arm/mach-kirkwood/board-readynas.c
 delete mode 100644 arch/arm/mach-kirkwood/board-sheevaplug.c
 delete mode 100644 arch/arm/mach-kirkwood/board-ts219.c
 delete mode 100644 arch/arm/mach-kirkwood/board-usi_topkick.c

diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
index 0f2aa61..b180588 100644
--- a/arch/arm/configs/kirkwood_defconfig
+++ b/arch/arm/configs/kirkwood_defconfig
@@ -29,30 +29,7 @@ CONFIG_MACH_SHEEVAPLUG=y
 CONFIG_MACH_T5325=y
 CONFIG_MACH_TS219=y
 CONFIG_MACH_TS41X=y
-CONFIG_MACH_CLOUDBOX_DT=y
-CONFIG_MACH_DB88F628X_BP_DT=y
 CONFIG_MACH_DLINK_KIRKWOOD_DT=y
-CONFIG_MACH_DOCKSTAR_DT=y
-CONFIG_MACH_DREAMPLUG_DT=y
-CONFIG_MACH_GOFLEXNET_DT=y
-CONFIG_MACH_GURUPLUG_DT=y
-CONFIG_MACH_IB62X0_DT=y
-CONFIG_MACH_ICONNECT_DT=y
-CONFIG_MACH_INETSPACE_V2_DT=y
-CONFIG_MACH_IOMEGA_IX2_200_DT=y
-CONFIG_MACH_KM_KIRKWOOD_DT=y
-CONFIG_MACH_LSXL_DT=y
-CONFIG_MACH_MPLCEC4_DT=y
-CONFIG_MACH_NETSPACE_LITE_V2_DT=y
-CONFIG_MACH_NETSPACE_MAX_V2_DT=y
-CONFIG_MACH_NETSPACE_MINI_V2_DT=y
-CONFIG_MACH_NETSPACE_V2_DT=y
-CONFIG_MACH_NSA310_DT=y
-CONFIG_MACH_OPENBLOCKS_A6_DT=y
-CONFIG_MACH_READYNAS_DT=y
-CONFIG_MACH_SHEEVAPLUG_DT=y
-CONFIG_MACH_TOPKICK_DT=y
-CONFIG_MACH_TS219_DT=y
 # CONFIG_CPU_FEROCEON_OLD_ID is not set
 CONFIG_PCI_MVEBU=y
 CONFIG_PREEMPT=y
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index b634f96..e28cb72 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -139,20 +139,6 @@ config ARCH_KIRKWOOD_DT
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Kirkwood using flattened device tree.
 
-config MACH_CLOUDBOX_DT
-	bool "LaCie CloudBox NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  CloudBox NAS, using Flattened Device Tree.
-
-config MACH_DB88F628X_BP_DT
-	bool "Marvell DB-88F628x-BP Development Board (Flattened Device Tree)"
-	help
-	  Say 'Y' here if you want your kernel to support the Marvell
-	  DB-88F6281-BP and DB-88F6282-BP Development Board (Flattened
-	  Device Tree).
-
 config MACH_DLINK_KIRKWOOD_DT
 	bool "D-Link Kirkwood-based NAS (Flattened Device Tree)"
 	select ARCH_KIRKWOOD_DT
@@ -161,163 +147,6 @@ config MACH_DLINK_KIRKWOOD_DT
 	  Kirkwood-based D-Link NASes such as DNS-320 & DNS-325,
 	  using Flattened Device Tree.
 
-config MACH_DOCKSTAR_DT
-	bool "Seagate FreeAgent Dockstar (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Seagate FreeAgent Dockstar (Flattened Device Tree).
-
-config MACH_DREAMPLUG_DT
-	bool "Marvell DreamPlug (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell DreamPlug (Flattened Device Tree).
-
-config MACH_GOFLEXNET_DT
-	bool "Seagate GoFlex Net (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Seagate GoFlex Net (Flattened Device Tree).
-
-config MACH_GURUPLUG_DT
-	bool "Marvell GuruPlug Reference Board (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell GuruPlug Reference Board (Flattened Device Tree).
-
-config MACH_IB62X0_DT
-	bool "RaidSonic IB-NAS6210, IB-NAS6220 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  RaidSonic IB-NAS6210 & IB-NAS6220 devices, using
-	  Flattened Device Tree.
-
-config MACH_ICONNECT_DT
-	bool "Iomega Iconnect (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here to enable Iomega Iconnect support.
-
-config MACH_INETSPACE_V2_DT
-	bool "LaCie Internet Space v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Internet Space v2 NAS, using Flattened Device Tree.
-
-config MACH_IOMEGA_IX2_200_DT
-	bool "Iomega StorCenter ix2-200 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Iomega StorCenter ix2-200 (Flattened Device Tree).
-
-config MACH_KM_KIRKWOOD_DT
-	bool "Keymile Kirkwood Reference Design (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Keymile Kirkwood Reference Desgin, using Flattened Device Tree.
-
-config MACH_LSXL_DT
-	bool "Buffalo Linkstation LS-XHL, LS-CHLv2 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	select POWER_RESET_RESTART
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Buffalo Linkstation LS-XHL & LS-CHLv2 devices, using
-	  Flattened Device Tree.
-
-config MACH_MPLCEC4_DT
-	bool "MPL CEC4 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  MPL CEC4 (Flattened Device Tree).
-
-config MACH_NETSPACE_LITE_V2_DT
-	bool "LaCie Network Space Lite v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space Lite v2 NAS, using Flattened Device Tree.
-
-config MACH_NETSPACE_MAX_V2_DT
-	bool "LaCie Network Space Max v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space Max v2 NAS, using Flattened Device Tree.
-
-config MACH_NETSPACE_MINI_V2_DT
-	bool "LaCie Network Space Mini v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space Mini v2 NAS using Flattened Device Tree.
-
-	  This board is embedded in a product named CloudBox, which
-	  provides automatic backup on a 100GB cloud storage. This
-	  should not confused with a more recent LaCie NAS also named
-	  CloudBox. For this last, the disk capacity is 1TB or above.
-
-config MACH_NETSPACE_V2_DT
-	bool "LaCie Network Space v2 NAS (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the LaCie
-	  Network Space v2 NAS, using Flattened Device Tree.
-
-config MACH_OPENBLOCKS_A6_DT
-	bool "Plat'Home OpenBlocks A6 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Plat'Home OpenBlocks A6 (Flattened Device Tree).
-
-config MACH_READYNAS_DT
-	bool "NETGEAR ReadyNAS Duo v2 (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	select ARM_APPENDED_DTB
-	select ARM_ATAG_DTB_COMPAT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  NETGEAR ReadyNAS Duo v2 using Fattened Device Tree.
-
-config MACH_SHEEVAPLUG_DT
-	bool "Marvell (eSATA) SheevaPlug (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  Marvell (eSATA) SheevaPlug (Flattened Device Tree).
-
-config MACH_TOPKICK_DT
-	bool "USI Topkick (Flattened Device Tree)"
-	select ARCH_KIRKWOOD_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  USI Topkick, using Flattened Device Tree
-
-config MACH_TS219_DT
-	bool "Device Tree for QNAP TS-11X, TS-21X NAS"
-	select ARCH_KIRKWOOD_DT
-	select ARM_APPENDED_DTB
-	select ARM_ATAG_DTB_COMPAT
-	select POWER_RESET_QNAP
-	help
-	  Say 'Y' here if you want your kernel to support the QNAP
-	  TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and
-	  TS-219P+ Turbo NAS devices using Fattened Device Tree.
-	  There are two different Device Tree descriptions, depending
-	  on if the device is based on an if the board uses the MV6281
-	  or MV6282. If you have the wrong one, the buttons will not
-	  work.
-
 endmenu
 
 endif
diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
index ac4cd75..9489c82 100644
--- a/arch/arm/mach-kirkwood/Makefile
+++ b/arch/arm/mach-kirkwood/Makefile
@@ -19,26 +19,4 @@ obj-$(CONFIG_MACH_TS219)		+= ts219-setup.o tsx1x-common.o
 obj-$(CONFIG_MACH_TS41X)		+= ts41x-setup.o tsx1x-common.o
 
 obj-$(CONFIG_ARCH_KIRKWOOD_DT)		+= board-dt.o
-obj-$(CONFIG_MACH_CLOUDBOX_DT)		+= board-ns2.o
-obj-$(CONFIG_MACH_DB88F628X_BP_DT)	+= board-db88f628x-bp.o
 obj-$(CONFIG_MACH_DLINK_KIRKWOOD_DT)	+= board-dnskw.o
-obj-$(CONFIG_MACH_DOCKSTAR_DT)		+= board-dockstar.o
-obj-$(CONFIG_MACH_DREAMPLUG_DT)		+= board-dreamplug.o
-obj-$(CONFIG_MACH_GOFLEXNET_DT)		+= board-goflexnet.o
-obj-$(CONFIG_MACH_GURUPLUG_DT)		+= board-guruplug.o
-obj-$(CONFIG_MACH_IB62X0_DT)		+= board-ib62x0.o
-obj-$(CONFIG_MACH_ICONNECT_DT)		+= board-iconnect.o
-obj-$(CONFIG_MACH_INETSPACE_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_IOMEGA_IX2_200_DT)	+= board-iomega_ix2_200.o
-obj-$(CONFIG_MACH_KM_KIRKWOOD_DT)	+= board-km_kirkwood.o
-obj-$(CONFIG_MACH_LSXL_DT)		+= board-lsxl.o
-obj-$(CONFIG_MACH_MPLCEC4_DT)		+= board-mplcec4.o
-obj-$(CONFIG_MACH_NETSPACE_LITE_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_NETSPACE_MAX_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_NETSPACE_MINI_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_NETSPACE_V2_DT)	+= board-ns2.o
-obj-$(CONFIG_MACH_OPENBLOCKS_A6_DT)	+= board-openblocks_a6.o
-obj-$(CONFIG_MACH_READYNAS_DT)		+= board-readynas.o
-obj-$(CONFIG_MACH_SHEEVAPLUG_DT)	+= board-sheevaplug.o
-obj-$(CONFIG_MACH_TOPKICK_DT)		+= board-usi_topkick.o
-obj-$(CONFIG_MACH_TS219_DT)		+= board-ts219.o tsx1x-common.o
diff --git a/arch/arm/mach-kirkwood/board-db88f628x-bp.c b/arch/arm/mach-kirkwood/board-db88f628x-bp.c
deleted file mode 100644
index 2f574bc..0000000
--- a/arch/arm/mach-kirkwood/board-db88f628x-bp.c
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * Saeed Bishara <saeed@marvell.com>
- *
- * Marvell DB-88F628{1,2}-BP Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/of.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data db88f628x_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init db88f628x_init(void)
-{
-	kirkwood_ge00_init(&db88f628x_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-dnskw.c b/arch/arm/mach-kirkwood/board-dnskw.c
index a1aa87f..2af7a95 100644
--- a/arch/arm/mach-kirkwood/board-dnskw.c
+++ b/arch/arm/mach-kirkwood/board-dnskw.c
@@ -14,14 +14,9 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
 #include <linux/gpio.h>
 #include "common.h"
 
-static struct mv643xx_eth_platform_data dnskw_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
 /* Register any GPIO for output and set the value */
 static void __init dnskw_gpio_register(unsigned gpio, char *name, int def)
 {
@@ -36,8 +31,6 @@ static void __init dnskw_gpio_register(unsigned gpio, char *name, int def)
 
 void __init dnskw_init(void)
 {
-	kirkwood_ge00_init(&dnskw_ge00_data);
-
 	/* Set NAS to turn back on after a power failure */
 	dnskw_gpio_register(37, "dnskw:power:recover", 1);
 }
diff --git a/arch/arm/mach-kirkwood/board-dockstar.c b/arch/arm/mach-kirkwood/board-dockstar.c
deleted file mode 100644
index d7196db..0000000
--- a/arch/arm/mach-kirkwood/board-dockstar.c
+++ /dev/null
@@ -1,32 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-dockstar.c
- *
- * Seagate FreeAgent Dockstar Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
- * Copied and modified for Seagate GoFlex Net support by
- * Joshua Coombs <josh.coombs@gmail.com> based on ArchLinux ARM's
- * GoFlex kernel patches.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data dockstar_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init dockstar_dt_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&dockstar_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-dreamplug.c b/arch/arm/mach-kirkwood/board-dreamplug.c
deleted file mode 100644
index 0903242..0000000
--- a/arch/arm/mach-kirkwood/board-dreamplug.c
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
- *
- * arch/arm/mach-kirkwood/board-dreamplug.c
- *
- * Marvell DreamPlug Reference Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data dreamplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data dreamplug_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-void __init dreamplug_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&dreamplug_ge00_data);
-	kirkwood_ge01_init(&dreamplug_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
index 6e122ed..a3271f6 100644
--- a/arch/arm/mach-kirkwood/board-dt.c
+++ b/arch/arm/mach-kirkwood/board-dt.c
@@ -102,96 +102,14 @@ static void __init kirkwood_dt_init(void)
 	kexec_reinit = kirkwood_enable_pcie;
 #endif
 
-	if (of_machine_is_compatible("globalscale,dreamplug"))
-		dreamplug_init();
-
-	if (of_machine_is_compatible("globalscale,guruplug"))
-		guruplug_dt_init();
-
-	if (of_machine_is_compatible("globalscale,sheevaplug"))
-		sheevaplug_dt_init();
-
 	if (of_machine_is_compatible("dlink,dns-kirkwood"))
 		dnskw_init();
 
-	if (of_machine_is_compatible("iom,iconnect"))
-		iconnect_init();
-
-	if (of_machine_is_compatible("raidsonic,ib-nas62x0"))
-		ib62x0_init();
-
-	if (of_machine_is_compatible("qnap,ts219"))
-		qnap_dt_ts219_init();
-
-	if (of_machine_is_compatible("seagate,dockstar"))
-		dockstar_dt_init();
-
-	if (of_machine_is_compatible("seagate,goflexnet"))
-		goflexnet_init();
-
-	if (of_machine_is_compatible("buffalo,lsxl"))
-		lsxl_init();
-
-	if (of_machine_is_compatible("iom,ix2-200"))
-		iomega_ix2_200_init();
-
-	if (of_machine_is_compatible("keymile,km_kirkwood"))
-		km_kirkwood_init();
-
-	if (of_machine_is_compatible("lacie,cloudbox") ||
-	    of_machine_is_compatible("lacie,inetspace_v2") ||
-	    of_machine_is_compatible("lacie,netspace_lite_v2") ||
-	    of_machine_is_compatible("lacie,netspace_max_v2") ||
-	    of_machine_is_compatible("lacie,netspace_mini_v2") ||
-	    of_machine_is_compatible("lacie,netspace_v2"))
-		ns2_init();
-
-	if (of_machine_is_compatible("marvell,db-88f6281-bp") ||
-	    of_machine_is_compatible("marvell,db-88f6282-bp"))
-		db88f628x_init();
-
-	if (of_machine_is_compatible("mpl,cec4"))
-		mplcec4_init();
-
-	if (of_machine_is_compatible("netgear,readynas-duo-v2"))
-		netgear_readynas_init();
-
-	if (of_machine_is_compatible("plathome,openblocks-a6"))
-		openblocks_a6_init();
-
-	if (of_machine_is_compatible("usi,topkick"))
-		usi_topkick_init();
-
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 
 static const char * const kirkwood_dt_board_compat[] = {
-	"globalscale,dreamplug",
-	"globalscale,guruplug",
-	"globalscale,sheevaplug",
-	"dlink,dns-320",
-	"dlink,dns-325",
-	"iom,iconnect",
-	"raidsonic,ib-nas62x0",
-	"qnap,ts219",
-	"seagate,dockstar",
-	"seagate,goflexnet",
-	"buffalo,lsxl",
-	"iom,ix2-200",
-	"keymile,km_kirkwood",
-	"lacie,cloudbox",
-	"lacie,inetspace_v2",
-	"lacie,netspace_lite_v2",
-	"lacie,netspace_max_v2",
-	"lacie,netspace_mini_v2",
-	"lacie,netspace_v2",
-	"marvell,db-88f6281-bp",
-	"marvell,db-88f6282-bp",
-	"mpl,cec4",
-	"netgear,readynas-duo-v2",
-	"plathome,openblocks-a6",
-	"usi,topkick",
-	"zyxel,nsa310",
+	"marvell,kirkwood",
 	NULL
 };
 
diff --git a/arch/arm/mach-kirkwood/board-goflexnet.c b/arch/arm/mach-kirkwood/board-goflexnet.c
deleted file mode 100644
index 9db979a..0000000
--- a/arch/arm/mach-kirkwood/board-goflexnet.c
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
- *
- * arch/arm/mach-kirkwood/board-goflexnet.c
- *
- * Seagate GoFlext Net Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
- * Copied and modified for Seagate GoFlex Net support by
- * Joshua Coombs <josh.coombs@gmail.com> based on ArchLinux ARM's
- * GoFlex kernel patches.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data goflexnet_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init goflexnet_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&goflexnet_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-guruplug.c b/arch/arm/mach-kirkwood/board-guruplug.c
deleted file mode 100644
index a857163..0000000
--- a/arch/arm/mach-kirkwood/board-guruplug.c
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-guruplug.c
- *
- * Marvell Guruplug Reference Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data guruplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data guruplug_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-void __init guruplug_dt_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&guruplug_ge00_data);
-	kirkwood_ge01_init(&guruplug_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-ib62x0.c b/arch/arm/mach-kirkwood/board-ib62x0.c
deleted file mode 100644
index 9a857ae..0000000
--- a/arch/arm/mach-kirkwood/board-ib62x0.c
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- * Copyright 2012 (C), Simon Baatz <gmbnomis@gmail.com>
- *
- * arch/arm/mach-kirkwood/board-ib62x0.c
- *
- * RaidSonic ICY BOX IB-NAS6210 & IB-NAS6220 init for drivers not
- * converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data ib62x0_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init ib62x0_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&ib62x0_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-iconnect.c b/arch/arm/mach-kirkwood/board-iconnect.c
deleted file mode 100644
index 98b5ad1..0000000
--- a/arch/arm/mach-kirkwood/board-iconnect.c
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-iconnect.c
- *
- * Iomega i-connect Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/of.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data iconnect_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(11),
-};
-
-void __init iconnect_init(void)
-{
-	kirkwood_ge00_init(&iconnect_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
deleted file mode 100644
index e5f7041..0000000
--- a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-iomega_ix2_200.c
- *
- * Iomega StorCenter ix2-200
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/ethtool.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = {
-	.phy_addr       = MV643XX_ETH_PHY_NONE,
-	.speed          = SPEED_1000,
-	.duplex         = DUPLEX_FULL,
-};
-
-static struct mv643xx_eth_platform_data iomega_ix2_200_ge01_data = {
-        .phy_addr       = MV643XX_ETH_PHY_ADDR(11),
-};
-
-void __init iomega_ix2_200_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&iomega_ix2_200_ge00_data);
-	kirkwood_ge01_init(&iomega_ix2_200_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-km_kirkwood.c b/arch/arm/mach-kirkwood/board-km_kirkwood.c
deleted file mode 100644
index 44e4605..0000000
--- a/arch/arm/mach-kirkwood/board-km_kirkwood.c
+++ /dev/null
@@ -1,44 +0,0 @@
-/*
- * Copyright 2012 2012 KEYMILE AG, CH-3097 Bern
- * Valentin Longchamp <valentin.longchamp@keymile.com>
- *
- * arch/arm/mach-kirkwood/board-km_kirkwood.c
- *
- * Keymile km_kirkwood Reference Desing Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/clk.h>
-#include <linux/clk-private.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data km_kirkwood_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init km_kirkwood_init(void)
-{
-	struct clk *sata_clk;
-	/*
-	 * Our variant of kirkwood (integrated in the Bobcat) hangs on accessing
-	 * SATA bits (14-15) of the Clock Gating Control Register. Since these
-	 * devices are also not present in this variant, their clocks get
-	 * disabled because unused when clk_disable_unused() gets called.
-	 * That's why we change the flags to these clocks to CLK_IGNORE_UNUSED
-	 */
-	sata_clk = clk_get_sys("sata_mv.0", "0");
-	if (!IS_ERR(sata_clk))
-		sata_clk->flags |= CLK_IGNORE_UNUSED;
-	sata_clk = clk_get_sys("sata_mv.0", "1");
-	if (!IS_ERR(sata_clk))
-		sata_clk->flags |= CLK_IGNORE_UNUSED;
-
-	kirkwood_ge00_init(&km_kirkwood_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-lsxl.c b/arch/arm/mach-kirkwood/board-lsxl.c
deleted file mode 100644
index 3483952..0000000
--- a/arch/arm/mach-kirkwood/board-lsxl.c
+++ /dev/null
@@ -1,36 +0,0 @@
-/*
- * Copyright 2012 (C), Michael Walle <michael@walle.cc>
- *
- * arch/arm/mach-kirkwood/board-lsxl.c
- *
- * Buffalo Linkstation LS-XHL and LS-CHLv2 init for drivers not
- * converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data lsxl_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-static struct mv643xx_eth_platform_data lsxl_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init lsxl_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-
-	kirkwood_ge00_init(&lsxl_ge00_data);
-	kirkwood_ge01_init(&lsxl_ge01_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-mplcec4.c b/arch/arm/mach-kirkwood/board-mplcec4.c
deleted file mode 100644
index 938712e..0000000
--- a/arch/arm/mach-kirkwood/board-mplcec4.c
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * Copyright (C) 2012 MPL AG, Switzerland
- * Stefan Peter <s.peter@mpl.ch>
- *
- * arch/arm/mach-kirkwood/board-mplcec4.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data mplcec4_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
-};
-
-static struct mv643xx_eth_platform_data mplcec4_ge01_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(2),
-};
-
-void __init mplcec4_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&mplcec4_ge00_data);
-	kirkwood_ge01_init(&mplcec4_ge01_data);
-}
-
-
-
diff --git a/arch/arm/mach-kirkwood/board-ns2.c b/arch/arm/mach-kirkwood/board-ns2.c
deleted file mode 100644
index f8f6605..0000000
--- a/arch/arm/mach-kirkwood/board-ns2.c
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * Copyright 2012 (C), Simon Guinot <simon.guinot@sequanux.org>
- *
- * arch/arm/mach-kirkwood/board-ns2.c
- *
- * LaCie Network Space v2 board (and parents) initialization for drivers
- * not converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/of.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data ns2_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init ns2_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	if (of_machine_is_compatible("lacie,cloudbox") ||
-	    of_machine_is_compatible("lacie,netspace_lite_v2") ||
-	    of_machine_is_compatible("lacie,netspace_mini_v2"))
-		ns2_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
-	kirkwood_ge00_init(&ns2_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-openblocks_a6.c b/arch/arm/mach-kirkwood/board-openblocks_a6.c
deleted file mode 100644
index b11d8fd..0000000
--- a/arch/arm/mach-kirkwood/board-openblocks_a6.c
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * Copyright 2012 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- *
- * arch/arm/mach-kirkwood/board-openblocks_a6.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data openblocks_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init openblocks_a6_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&openblocks_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-readynas.c b/arch/arm/mach-kirkwood/board-readynas.c
deleted file mode 100644
index 341b82d..0000000
--- a/arch/arm/mach-kirkwood/board-readynas.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * NETGEAR ReadyNAS Duo v2 Board setup for drivers not already
- * converted to DT.
- *
- * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data netgear_readynas_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init netgear_readynas_init(void)
-{
-	kirkwood_ge00_init(&netgear_readynas_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-sheevaplug.c b/arch/arm/mach-kirkwood/board-sheevaplug.c
deleted file mode 100644
index fa38937..0000000
--- a/arch/arm/mach-kirkwood/board-sheevaplug.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-kirkwood/board-sheevaplug.c
- *
- * Marvell Sheevaplug Reference Board Init for drivers not converted to
- * flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data sheevaplug_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init sheevaplug_dt_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&sheevaplug_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-ts219.c b/arch/arm/mach-kirkwood/board-ts219.c
deleted file mode 100644
index 860f44a..0000000
--- a/arch/arm/mach-kirkwood/board-ts219.c
+++ /dev/null
@@ -1,40 +0,0 @@
-/*
- *
- * QNAP TS-11x/TS-21x Turbo NAS Board Setup via DT
- *
- * Copyright (C) 2012 Andrew Lunn <andrew@lunn.ch>
- *
- * Based on the board file ts219-setup.c:
- *
- * Copyright (C) 2009  Martin Michlmayr <tbm@cyrius.com>
- * Copyright (C) 2008  Byron Bradley <byron.bbradley@gmail.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx_eth.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/kirkwood.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data qnap_ts219_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-void __init qnap_dt_ts219_init(void)
-{
-	u32 dev, rev;
-
-	kirkwood_pcie_id(&dev, &rev);
-	if (dev == MV88F6282_DEV_ID)
-		qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
-
-	kirkwood_ge00_init(&qnap_ts219_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/board-usi_topkick.c b/arch/arm/mach-kirkwood/board-usi_topkick.c
deleted file mode 100644
index 1cc04ec..0000000
--- a/arch/arm/mach-kirkwood/board-usi_topkick.c
+++ /dev/null
@@ -1,29 +0,0 @@
-/*
- * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
- *
- * arch/arm/mach-kirkwood/board-usi_topkick.c
- *
- * USI Topkick Init for drivers not converted to flattened device tree yet.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/gpio.h>
-#include "common.h"
-
-static struct mv643xx_eth_platform_data topkick_ge00_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
-};
-
-void __init usi_topkick_init(void)
-{
-	/*
-	 * Basic setup. Needs to be called early.
-	 */
-	kirkwood_ge00_init(&topkick_ge00_data);
-}
diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
index fcf3ba6..9d8caae 100644
--- a/arch/arm/mach-kirkwood/common.h
+++ b/arch/arm/mach-kirkwood/common.h
@@ -59,121 +59,12 @@ void kirkwood_restart(enum reboot_mode, const char *);
 void kirkwood_clk_init(void);
 
 /* board init functions for boards not fully converted to fdt */
-#ifdef CONFIG_MACH_DREAMPLUG_DT
-void dreamplug_init(void);
-#else
-static inline void dreamplug_init(void) {};
-#endif
-#ifdef CONFIG_MACH_GURUPLUG_DT
-void guruplug_dt_init(void);
-#else
-static inline void guruplug_dt_init(void) {};
-#endif
-#ifdef CONFIG_MACH_SHEEVAPLUG_DT
-void sheevaplug_dt_init(void);
-#else
-static inline void sheevaplug_dt_init(void) {};
-#endif
-#ifdef CONFIG_MACH_TS219_DT
-void qnap_dt_ts219_init(void);
-#else
-static inline void qnap_dt_ts219_init(void) {};
-#endif
-
 #ifdef CONFIG_MACH_DLINK_KIRKWOOD_DT
 void dnskw_init(void);
 #else
 static inline void dnskw_init(void) {};
 #endif
 
-#ifdef CONFIG_MACH_ICONNECT_DT
-void iconnect_init(void);
-#else
-static inline void iconnect_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_IB62X0_DT
-void ib62x0_init(void);
-#else
-static inline void ib62x0_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_DOCKSTAR_DT
-void dockstar_dt_init(void);
-#else
-static inline void dockstar_dt_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_GOFLEXNET_DT
-void goflexnet_init(void);
-#else
-static inline void goflexnet_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_LSXL_DT
-void lsxl_init(void);
-#else
-static inline void lsxl_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_IOMEGA_IX2_200_DT
-void iomega_ix2_200_init(void);
-#else
-static inline void iomega_ix2_200_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_KM_KIRKWOOD_DT
-void km_kirkwood_init(void);
-#else
-static inline void km_kirkwood_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_DB88F628X_BP_DT
-void db88f628x_init(void);
-#else
-static inline void db88f628x_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_MPLCEC4_DT
-void mplcec4_init(void);
-#else
-static inline void mplcec4_init(void) {};
-#endif
-
-#if defined(CONFIG_MACH_INETSPACE_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_MAX_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_LITE_V2_DT) || \
-	defined(CONFIG_MACH_NETSPACE_MINI_V2_DT)
-void ns2_init(void);
-#else
-static inline void ns2_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_OPENBLOCKS_A6_DT
-void openblocks_a6_init(void);
-#else
-static inline void openblocks_a6_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_READYNAS_DT
-void netgear_readynas_init(void);
-#else
-static inline void netgear_readynas_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_TOPKICK_DT
-void usi_topkick_init(void);
-#else
-static inline void usi_topkick_init(void) {};
-#endif
-
-#ifdef CONFIG_MACH_CLOUDBOX_DT
-void cloudbox_init(void);
-#else
-static inline void cloudbox_init(void) {};
-#endif
-
 /* early init functions not converted to fdt yet */
 char *kirkwood_id(void);
 void kirkwood_l2_init(void);
-- 
1.7.2.5

[PATCH v7 2/7] ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes

[Sebastian Hesselbarth]

This patch adds mv643xx_eth and mvmdio device tree nodes for DT enabled
Kirkwood boards. Phy nodes are also added with reg property set on a
per-board basis.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
---
Changelog:
v6->v7:
- fix ethernet 1 port 0 name in kirkwood.dtsi (Reported by Jonas Gorski)

v5->v6:
- rebase for v3.11-rc1
- also convert Sheevaplug and DB628x

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
---
 arch/arm/boot/dts/kirkwood-cloudbox.dts            |   16 ++++++
 arch/arm/boot/dts/kirkwood-db.dtsi                 |   16 ++++++
 arch/arm/boot/dts/kirkwood-dnskw.dtsi              |   16 ++++++
 arch/arm/boot/dts/kirkwood-dockstar.dts            |   17 +++++++
 arch/arm/boot/dts/kirkwood-dreamplug.dts           |   28 +++++++++++
 arch/arm/boot/dts/kirkwood-goflexnet.dts           |   16 ++++++
 .../arm/boot/dts/kirkwood-guruplug-server-plus.dts |   30 +++++++++++
 arch/arm/boot/dts/kirkwood-ib62x0.dts              |   16 ++++++
 arch/arm/boot/dts/kirkwood-iconnect.dts            |   16 ++++++
 arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts      |   24 +++++++++
 arch/arm/boot/dts/kirkwood-is2.dts                 |    2 +
 arch/arm/boot/dts/kirkwood-km_kirkwood.dts         |   16 ++++++
 arch/arm/boot/dts/kirkwood-lsxl.dtsi               |   28 +++++++++++
 arch/arm/boot/dts/kirkwood-mplcec4.dts             |   27 ++++++++++
 .../boot/dts/kirkwood-netgear_readynas_duo_v2.dts  |   16 ++++++
 arch/arm/boot/dts/kirkwood-ns2-common.dtsi         |   16 ++++++
 arch/arm/boot/dts/kirkwood-ns2.dts                 |    2 +
 arch/arm/boot/dts/kirkwood-ns2lite.dts             |    2 +
 arch/arm/boot/dts/kirkwood-ns2max.dts              |    2 +
 arch/arm/boot/dts/kirkwood-ns2mini.dts             |    2 +
 arch/arm/boot/dts/kirkwood-openblocks_a6.dts       |   16 ++++++
 arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi  |   16 ++++++
 arch/arm/boot/dts/kirkwood-topkick.dts             |   16 ++++++
 arch/arm/boot/dts/kirkwood-ts219-6281.dts          |    4 +-
 arch/arm/boot/dts/kirkwood-ts219-6282.dts          |    4 +-
 arch/arm/boot/dts/kirkwood-ts219.dtsi              |   16 ++++++
 arch/arm/boot/dts/kirkwood.dtsi                    |   52 ++++++++++++++++++++
 27 files changed, 430 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/kirkwood-cloudbox.dts b/arch/arm/boot/dts/kirkwood-cloudbox.dts
index 00c48d2..85eed62 100644
--- a/arch/arm/boot/dts/kirkwood-cloudbox.dts
+++ b/arch/arm/boot/dts/kirkwood-cloudbox.dts
@@ -89,3 +89,19 @@
 		gpios = <&gpio0 17 0>;
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-db.dtsi b/arch/arm/boot/dts/kirkwood-db.dtsi
index c87cfb8..ca8bf36 100644
--- a/arch/arm/boot/dts/kirkwood-db.dtsi
+++ b/arch/arm/boot/dts/kirkwood-db.dtsi
@@ -87,3 +87,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-dnskw.dtsi b/arch/arm/boot/dts/kirkwood-dnskw.dtsi
index 0afe1d0..f600ed7 100644
--- a/arch/arm/boot/dts/kirkwood-dnskw.dtsi
+++ b/arch/arm/boot/dts/kirkwood-dnskw.dtsi
@@ -219,3 +219,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/kirkwood-dockstar.dts
index 7714742..915aca6 100644
--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
@@ -90,3 +90,20 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		compatible = "marvell,88e1116";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/kirkwood-dreamplug.dts
index 36c7ba3..300fbf8 100644
--- a/arch/arm/boot/dts/kirkwood-dreamplug.dts
+++ b/arch/arm/boot/dts/kirkwood-dreamplug.dts
@@ -99,3 +99,31 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		device_type = "ethernet-phy";
+		reg = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts
index 31caa64..e9ba68e 100644
--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
@@ -170,3 +170,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts b/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
index 1e642f3..e696c31 100644
--- a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
+++ b/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
@@ -96,3 +96,33 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		compatible = "marvell,88e1121";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		device_type = "ethernet-phy";
+		compatible = "marvell,88e1121";
+		reg = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/kirkwood-ib62x0.dts
index 20c4b08..69019b8 100644
--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
+++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
@@ -122,3 +122,19 @@
 
 
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts
index 441204e..3d99164 100644
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
@@ -176,3 +176,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@11 {
+		device_type = "ethernet-phy";
+		reg = <11>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
index 00a7bfe..b08c733 100644
--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
@@ -194,3 +194,27 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy1: ethernet-phy@11 {
+		device_type = "ethernet-phy";
+		reg = <11>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-is2.dts b/arch/arm/boot/dts/kirkwood-is2.dts
index c3f036b..ff9be45 100644
--- a/arch/arm/boot/dts/kirkwood-is2.dts
+++ b/arch/arm/boot/dts/kirkwood-is2.dts
@@ -30,3 +30,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
index 5d9f5ea..466280b 100644
--- a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
+++ b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
@@ -50,3 +50,19 @@
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-lsxl.dtsi b/arch/arm/boot/dts/kirkwood-lsxl.dtsi
index 31b17f5..93397b1 100644
--- a/arch/arm/boot/dts/kirkwood-lsxl.dtsi
+++ b/arch/arm/boot/dts/kirkwood-lsxl.dtsi
@@ -207,3 +207,31 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@8 {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-mplcec4.dts b/arch/arm/boot/dts/kirkwood-mplcec4.dts
index 6179333..def825f 100644
--- a/arch/arm/boot/dts/kirkwood-mplcec4.dts
+++ b/arch/arm/boot/dts/kirkwood-mplcec4.dts
@@ -191,3 +191,30 @@
 	};
 };
 
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@1 {
+		device_type = "ethernet-phy";
+		reg = <1>;
+	};
+
+	ethphy1: ethernet-phy@2 {
+		device_type = "ethernet-phy";
+		reg = <2>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
index ad6ade7..716b203 100644
--- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
+++ b/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
@@ -184,3 +184,19 @@
                 };
         };
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
index 2afac04..e7b8017 100644
--- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
@@ -84,3 +84,19 @@
 	};
 
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy {
+		device_type = "ethernet-phy";
+                /* overwrite reg property in board file */
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ns2.dts b/arch/arm/boot/dts/kirkwood-ns2.dts
index b50e93d..e93276d 100644
--- a/arch/arm/boot/dts/kirkwood-ns2.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2.dts
@@ -30,3 +30,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-ns2lite.dts b/arch/arm/boot/dts/kirkwood-ns2lite.dts
index af8259f..34f5e69 100644
--- a/arch/arm/boot/dts/kirkwood-ns2lite.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2lite.dts
@@ -30,3 +30,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <0>; };
diff --git a/arch/arm/boot/dts/kirkwood-ns2max.dts b/arch/arm/boot/dts/kirkwood-ns2max.dts
index 85f24d2..f834c55 100644
--- a/arch/arm/boot/dts/kirkwood-ns2max.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2max.dts
@@ -49,3 +49,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-ns2mini.dts b/arch/arm/boot/dts/kirkwood-ns2mini.dts
index 329e530..b6b66ea 100644
--- a/arch/arm/boot/dts/kirkwood-ns2mini.dts
+++ b/arch/arm/boot/dts/kirkwood-ns2mini.dts
@@ -50,3 +50,5 @@
 		};
 	};
 };
+
+&ethphy0 { reg = <0>; };
diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
index 38dc851..7235f0c 100644
--- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
+++ b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
@@ -166,3 +166,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
index f7143f1..f55a145 100644
--- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
@@ -91,3 +91,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-topkick.dts b/arch/arm/boot/dts/kirkwood-topkick.dts
index f2052d7..184b8c5 100644
--- a/arch/arm/boot/dts/kirkwood-topkick.dts
+++ b/arch/arm/boot/dts/kirkwood-topkick.dts
@@ -203,3 +203,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6281.dts b/arch/arm/boot/dts/kirkwood-ts219-6281.dts
index 6dd1038..222435d 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6281.dts
+++ b/arch/arm/boot/dts/kirkwood-ts219-6281.dts
@@ -50,4 +50,6 @@
 			gpios = <&gpio0 16 1>;
 		};
 	};
-};
\ No newline at end of file
+};
+
+&ethphy0 { reg = <8>; };
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6282.dts b/arch/arm/boot/dts/kirkwood-ts219-6282.dts
index 6fdc5ff..510c555 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6282.dts
+++ b/arch/arm/boot/dts/kirkwood-ts219-6282.dts
@@ -58,4 +58,6 @@
 			gpios = <&gpio1 5 1>;
 		};
 	};
-};
\ No newline at end of file
+};
+
+&ethphy0 { reg = <0>; };
diff --git a/arch/arm/boot/dts/kirkwood-ts219.dtsi b/arch/arm/boot/dts/kirkwood-ts219.dtsi
index 0c9a94c..102eaeb 100644
--- a/arch/arm/boot/dts/kirkwood-ts219.dtsi
+++ b/arch/arm/boot/dts/kirkwood-ts219.dtsi
@@ -96,3 +96,19 @@
 		};
 	};
 };
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy {
+		device_type = "ethernet-phy";
+                /* overwrite reg property in board file */
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 9809fc1..e3f3f71 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -192,5 +192,57 @@
 			clocks = <&gate_clk 17>;
 			status = "okay";
 		};
+
+		mdio: mdio-bus@72004 {
+			compatible = "marvell,orion-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72004 0x84>;
+			interrupts = <46>;
+			clocks = <&gate_clk 0>;
+			status = "disabled";
+
+			/* add phy nodes in board file */
+		};
+
+		eth0: ethernet-controller@72000 {
+			compatible = "marvell,kirkwood-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x72000 0x4000>;
+			clocks = <&gate_clk 0>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet0-port@0 {
+				device_type = "network";
+				compatible = "marvell,kirkwood-eth-port";
+				reg = <0>;
+				interrupts = <11>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				/* set phy-handle property in board file */
+			};
+		};
+
+		eth1: ethernet-controller@76000 {
+			compatible = "marvell,kirkwood-eth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x76000 0x4000>;
+			clocks = <&gate_clk 19>;
+			marvell,tx-checksum-limit = <1600>;
+			status = "disabled";
+
+			ethernet1-port@0 {
+				device_type = "network";
+				compatible = "marvell,kirkwood-eth-port";
+				reg = <0>;
+				interrupts = <15>;
+				/* overwrite MAC address in bootloader */
+				local-mac-address = [00 00 00 00 00 00];
+				/* set phy-handle property in board file */
+			};
+		};
 	};
 };
-- 
1.7.10.4

Re: [PATCH v6 0/7] ARM: mvebu: switch to DT probed mv643xx_eth

[Jason Cooper]

On Tue, Jul 02, 2013 at 01:00:17PM +0200, Sebastian Hesselbarth wrote:
> This patch set converts Marvell Dove, Kirkwood, and Orion5x DT enabled
> boards to probe mv643xx_eth by DT. The corresponding DT support patches
> for mv643xx_eth driver have already been taked by David Miller and are
> available in next-20130701. This only contains the ARM part of
> mv643xx_eth DT support patches and therefore patch counting is
> continued as v6 with respect to the combined patch set.
> 
> The first three patches add nodes for ethernet-controller, mdio-bus,
> and ethernet PHYs found on the three SoCs and their boards.
> 
> The last four patches convert DT boards for each SoC from platform_device
> registration to DT based probing by removing the corresponding calls.
> For Kirkwood this makes almost all DT board setup (except board-dnskw)
> obsolete. Therefore, patch 5 removes board setup files, Kconfig, Makefile,
> and defconfig entries for those boards.
> 
> This patch set has been tested on Marvell Dove, and compile-tested for
> Kirkwood and Orion5x defconfig on top of next-20130701 with some fixes
> sent earlier applied (DMA_MEMSET fixes and missing include on edmini_v2).
> 
> netdev is added on Cc for completeness, this is all Marvell related and
> should go through Jason Cooper's branch if there are no objections.
> 
> Sebastian Hesselbarth (7):
>   ARM: dove: add gigabit ethernet and mvmdio device tree nodes
>   ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes
>   ARM: orion5x: add gigabit ethernet and mvmdio device tree nodes
>   ARM: dove: remove legacy mv643xx_eth setup
>   ARM: kirkwood: remove redundant DT board files
>   ARM: kirkwood: remove legacy clk alias for mv643xx_eth
>   ARM: orion5x: remove legacy mv643xx_eth board setup
> 
>  arch/arm/boot/dts/dove-cubox.dts                   |    7 +
>  arch/arm/boot/dts/dove.dtsi                        |   35 +++++
>  arch/arm/boot/dts/kirkwood-cloudbox.dts            |   16 ++
>  arch/arm/boot/dts/kirkwood-db.dtsi                 |   16 ++
>  arch/arm/boot/dts/kirkwood-dnskw.dtsi              |   16 ++
>  arch/arm/boot/dts/kirkwood-dockstar.dts            |   17 ++
>  arch/arm/boot/dts/kirkwood-dreamplug.dts           |   28 ++++
>  arch/arm/boot/dts/kirkwood-goflexnet.dts           |   16 ++
>  .../arm/boot/dts/kirkwood-guruplug-server-plus.dts |   30 ++++
>  arch/arm/boot/dts/kirkwood-ib62x0.dts              |   16 ++
>  arch/arm/boot/dts/kirkwood-iconnect.dts            |   16 ++
>  arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts      |   24 +++
>  arch/arm/boot/dts/kirkwood-is2.dts                 |    2 +
>  arch/arm/boot/dts/kirkwood-km_kirkwood.dts         |   16 ++
>  arch/arm/boot/dts/kirkwood-lsxl.dtsi               |   28 ++++
>  arch/arm/boot/dts/kirkwood-mplcec4.dts             |   27 ++++
>  .../boot/dts/kirkwood-netgear_readynas_duo_v2.dts  |   16 ++
>  arch/arm/boot/dts/kirkwood-ns2-common.dtsi         |   16 ++
>  arch/arm/boot/dts/kirkwood-ns2.dts                 |    2 +
>  arch/arm/boot/dts/kirkwood-ns2lite.dts             |    2 +
>  arch/arm/boot/dts/kirkwood-ns2max.dts              |    2 +
>  arch/arm/boot/dts/kirkwood-ns2mini.dts             |    2 +
>  arch/arm/boot/dts/kirkwood-openblocks_a6.dts       |   16 ++
>  arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi  |   16 ++
>  arch/arm/boot/dts/kirkwood-topkick.dts             |   16 ++
>  arch/arm/boot/dts/kirkwood-ts219-6281.dts          |    4 +-
>  arch/arm/boot/dts/kirkwood-ts219-6282.dts          |    4 +-
>  arch/arm/boot/dts/kirkwood-ts219.dtsi              |   16 ++
>  arch/arm/boot/dts/kirkwood.dtsi                    |   52 +++++++
>  .../dts/orion5x-lacie-ethernet-disk-mini-v2.dts    |   17 ++
>  arch/arm/boot/dts/orion5x.dtsi                     |   29 ++++
>  arch/arm/configs/kirkwood_defconfig                |   22 ---
>  arch/arm/mach-dove/board-dt.c                      |    9 -
>  arch/arm/mach-kirkwood/Kconfig                     |  156 --------------------
>  arch/arm/mach-kirkwood/Makefile                    |   23 +---
>  arch/arm/mach-kirkwood/board-db88f628x-bp.c        |   24 ---
>  arch/arm/mach-kirkwood/board-dnskw.c               |    7 -
>  arch/arm/mach-kirkwood/board-dockstar.c            |   32 ----
>  arch/arm/mach-kirkwood/board-dreamplug.c           |   35 -----
>  arch/arm/mach-kirkwood/board-dt.c                  |   86 +-----------
>  arch/arm/mach-kirkwood/board-goflexnet.c           |   34 -----
>  arch/arm/mach-kirkwood/board-guruplug.c            |   33 ----
>  arch/arm/mach-kirkwood/board-ib62x0.c              |   29 ----
>  arch/arm/mach-kirkwood/board-iconnect.c            |   24 ---
>  arch/arm/mach-kirkwood/board-iomega_ix2_200.c      |   34 -----
>  arch/arm/mach-kirkwood/board-km_kirkwood.c         |   44 ------
>  arch/arm/mach-kirkwood/board-lsxl.c                |   36 -----
>  arch/arm/mach-kirkwood/board-mplcec4.c             |   35 -----
>  arch/arm/mach-kirkwood/board-ns2.c                 |   35 -----
>  arch/arm/mach-kirkwood/board-openblocks_a6.c       |   26 ----
>  arch/arm/mach-kirkwood/board-readynas.c            |   27 ----
>  arch/arm/mach-kirkwood/board-sheevaplug.c          |   27 ----
>  arch/arm/mach-kirkwood/board-ts219.c               |   40 -----
>  arch/arm/mach-kirkwood/board-usi_topkick.c         |   29 ----
>  arch/arm/mach-orion5x/edmini_v2-setup.c            |   10 --
>  55 files changed, 520 insertions(+), 857 deletions(-)
>  delete mode 100644 arch/arm/mach-kirkwood/board-db88f628x-bp.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-dockstar.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-dreamplug.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-goflexnet.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-guruplug.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-ib62x0.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-iconnect.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-iomega_ix2_200.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-km_kirkwood.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-lsxl.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-mplcec4.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-ns2.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-openblocks_a6.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-readynas.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-sheevaplug.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-ts219.c
>  delete mode 100644 arch/arm/mach-kirkwood/board-usi_topkick.c

Applied whole series to mvebu/boards (v7 of #2 and #5)

thx,

Jason.