[PATCH net-next 00/19] mlxsw: Preparations for VxLAN support

[PATCH net-next 00/19] mlxsw: Preparations for VxLAN support

[Ido Schimmel]

This patchset prepares mlxsw for VxLAN support. It contains small and
mostly non-functional changes.

The first eight patches perform small changes in the code to make it
more receptive towards the actual VxLAN changes in the next patchset.

Patches 9-17 add the registers used to configure the device for VxLAN
offload.

Last two patches add the required resources and trap IDs.

The next patchset is available here [1].

1. https://github.com/idosch/linux/tree/vxlan

Ido Schimmel (19):
  mlxsw: spectrum: Remove misuses of private header file
  mlxsw: spectrum_switchdev: Prepare for VxLAN FDB notifications
  mlxsw: spectrum_switchdev: Check notification relevance based on upper
    device
  mlxsw: spectrum_switchdev: Do not assume notifier information type
  mlxsw: spectrum: Move L3 protocol and address definitions to global
    header file
  mlxsw: spectrum: Add a new type of KVD linear record
  mlxsw: reg: Extend FDB flush types for NVE
  mlxsw: spectrum: Seed LAG hash function
  mlxsw: reg: Add Tunneling NVE General Configuration Register
  mlxsw: reg: Add Tunnel Port Configuration Register
  mlxsw: reg: Add Tunneling NVE Underlay Multicast Table Register
  mlxsw: reg: Add Tunneling NVE Encapsulation ECN Mapping Register
  mlxsw: reg: Add Tunneling NVE Decapsulation ECN Mapping Register
  mlxsw: reg: Add Tunneling NVE QoS Configuration Register
  mlxsw: reg: Add Tunneling NVE QoS Default Register
  mlxsw: reg: Add definition of unicast tunnel record for SFD register
  mlxsw: reg: Add Monitoring Parsing State Register
  mlxsw: resources: Add NVE resources
  mlxsw: spectrum: Add NVE packet traps

 drivers/net/ethernet/mellanox/mlxsw/reg.h     | 581 +++++++++++++++++-
 .../net/ethernet/mellanox/mlxsw/resources.h   |   4 +
 .../net/ethernet/mellanox/mlxsw/spectrum.c    |   8 +-
 .../net/ethernet/mellanox/mlxsw/spectrum.h    |  17 +
 .../ethernet/mellanox/mlxsw/spectrum2_kvdl.c  |   1 +
 .../ethernet/mellanox/mlxsw/spectrum_router.h |  15 -
 .../mellanox/mlxsw/spectrum_switchdev.c       |  21 +-
 drivers/net/ethernet/mellanox/mlxsw/trap.h    |   2 +
 8 files changed, 627 insertions(+), 22 deletions(-)

-- 
2.17.1

[PATCH net-next 01/19] mlxsw: spectrum: Remove misuses of private header file

[Ido Schimmel]

The spectrum_router.h header file is private to the router block and
should only be included by direct consumers of it, such as dpipe and the
multicast routing code.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/spectrum.h           | 4 ++++
 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.h    | 4 ----
 drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c | 1 -
 3 files changed, 4 insertions(+), 5 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum.h b/drivers/net/ethernet/mellanox/mlxsw/spectrum.h
index 3cdb7aca90b7..206ecc69b51c 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum.h
@@ -416,6 +416,10 @@ mlxsw_sp_port_vlan_router_leave(struct mlxsw_sp_port_vlan *mlxsw_sp_port_vlan);
 void mlxsw_sp_rif_destroy(struct mlxsw_sp_rif *rif);
 void mlxsw_sp_rif_destroy_by_dev(struct mlxsw_sp *mlxsw_sp,
 				 struct net_device *dev);
+struct mlxsw_sp_rif *mlxsw_sp_rif_find_by_dev(const struct mlxsw_sp *mlxsw_sp,
+					      const struct net_device *dev);
+u8 mlxsw_sp_router_port(const struct mlxsw_sp *mlxsw_sp);
+struct mlxsw_sp_fid *mlxsw_sp_rif_fid(const struct mlxsw_sp_rif *rif);
 
 /* spectrum_kvdl.c */
 enum mlxsw_sp_kvdl_entry_type {
diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.h b/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.h
index 1a60391daafa..354cb0834f3a 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.h
@@ -35,8 +35,6 @@ struct mlxsw_sp_neigh_entry;
 struct mlxsw_sp_nexthop;
 struct mlxsw_sp_ipip_entry;
 
-struct mlxsw_sp_rif *mlxsw_sp_rif_find_by_dev(const struct mlxsw_sp *mlxsw_sp,
-					      const struct net_device *dev);
 struct mlxsw_sp_rif *mlxsw_sp_rif_by_index(const struct mlxsw_sp *mlxsw_sp,
 					   u16 rif_index);
 u16 mlxsw_sp_rif_index(const struct mlxsw_sp_rif *rif);
@@ -44,9 +42,7 @@ u16 mlxsw_sp_ipip_lb_rif_index(const struct mlxsw_sp_rif_ipip_lb *rif);
 u16 mlxsw_sp_ipip_lb_ul_vr_id(const struct mlxsw_sp_rif_ipip_lb *rif);
 u32 mlxsw_sp_ipip_dev_ul_tb_id(const struct net_device *ol_dev);
 int mlxsw_sp_rif_dev_ifindex(const struct mlxsw_sp_rif *rif);
-u8 mlxsw_sp_router_port(const struct mlxsw_sp *mlxsw_sp);
 const struct net_device *mlxsw_sp_rif_dev(const struct mlxsw_sp_rif *rif);
-struct mlxsw_sp_fid *mlxsw_sp_rif_fid(const struct mlxsw_sp_rif *rif);
 int mlxsw_sp_rif_counter_value_get(struct mlxsw_sp *mlxsw_sp,
 				   struct mlxsw_sp_rif *rif,
 				   enum mlxsw_sp_rif_counter_dir dir,
diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
index db715da7bab7..1a9370a46b0e 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
@@ -17,7 +17,6 @@
 #include <net/switchdev.h>
 
 #include "spectrum_span.h"
-#include "spectrum_router.h"
 #include "spectrum_switchdev.h"
 #include "spectrum.h"
 #include "core.h"
-- 
2.17.1

[PATCH net-next 02/19] mlxsw: spectrum_switchdev: Prepare for VxLAN FDB notifications

[Ido Schimmel]

VxLAN FDB notifications need to be handled differently than bridge FDB
notifications, so initialize the work item based on the received
notification and rename the invoked function accordingly.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
index 1a9370a46b0e..c9c605fdce10 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
@@ -2288,7 +2288,7 @@ struct mlxsw_sp_switchdev_event_work {
 	unsigned long event;
 };
 
-static void mlxsw_sp_switchdev_event_work(struct work_struct *work)
+static void mlxsw_sp_switchdev_bridge_fdb_event_work(struct work_struct *work)
 {
 	struct mlxsw_sp_switchdev_event_work *switchdev_work =
 		container_of(work, struct mlxsw_sp_switchdev_event_work, work);
@@ -2352,7 +2352,6 @@ static int mlxsw_sp_switchdev_event(struct notifier_block *unused,
 	if (!switchdev_work)
 		return NOTIFY_BAD;
 
-	INIT_WORK(&switchdev_work->work, mlxsw_sp_switchdev_event_work);
 	switchdev_work->dev = dev;
 	switchdev_work->event = event;
 
@@ -2361,6 +2360,8 @@ static int mlxsw_sp_switchdev_event(struct notifier_block *unused,
 	case SWITCHDEV_FDB_DEL_TO_DEVICE: /* fall through */
 	case SWITCHDEV_FDB_ADD_TO_BRIDGE: /* fall through */
 	case SWITCHDEV_FDB_DEL_TO_BRIDGE:
+		INIT_WORK(&switchdev_work->work,
+			  mlxsw_sp_switchdev_bridge_fdb_event_work);
 		memcpy(&switchdev_work->fdb_info, ptr,
 		       sizeof(switchdev_work->fdb_info));
 		switchdev_work->fdb_info.addr = kzalloc(ETH_ALEN, GFP_ATOMIC);
-- 
2.17.1

[PATCH net-next 03/19] mlxsw: spectrum_switchdev: Check notification relevance based on upper device

[Ido Schimmel]

VxLAN FDB updates are sent with the VxLAN device which is not our upper
and will therefore be ignored by current code.

Solve this by checking whether the upper device (bridge) is our upper.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
index c9c605fdce10..9edaec95ddd2 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
@@ -2344,8 +2344,15 @@ static int mlxsw_sp_switchdev_event(struct notifier_block *unused,
 	struct net_device *dev = switchdev_notifier_info_to_dev(ptr);
 	struct mlxsw_sp_switchdev_event_work *switchdev_work;
 	struct switchdev_notifier_fdb_info *fdb_info = ptr;
+	struct net_device *br_dev;
 
-	if (!mlxsw_sp_port_dev_lower_find_rcu(dev))
+	/* Tunnel devices are not our uppers, so check their master instead */
+	br_dev = netdev_master_upper_dev_get_rcu(dev);
+	if (!br_dev)
+		return NOTIFY_DONE;
+	if (!netif_is_bridge_master(br_dev))
+		return NOTIFY_DONE;
+	if (!mlxsw_sp_port_dev_lower_find_rcu(br_dev))
 		return NOTIFY_DONE;
 
 	switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC);
-- 
2.17.1

[PATCH net-next 04/19] mlxsw: spectrum_switchdev: Do not assume notifier information type

[Ido Schimmel]

VxLAN notifications are going to use a different notifier information
type, so cast to the correct type based on the received event.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
index 9edaec95ddd2..fa16ad2c6a50 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
@@ -2343,7 +2343,8 @@ static int mlxsw_sp_switchdev_event(struct notifier_block *unused,
 {
 	struct net_device *dev = switchdev_notifier_info_to_dev(ptr);
 	struct mlxsw_sp_switchdev_event_work *switchdev_work;
-	struct switchdev_notifier_fdb_info *fdb_info = ptr;
+	struct switchdev_notifier_fdb_info *fdb_info;
+	struct switchdev_notifier_info *info = ptr;
 	struct net_device *br_dev;
 
 	/* Tunnel devices are not our uppers, so check their master instead */
@@ -2367,6 +2368,9 @@ static int mlxsw_sp_switchdev_event(struct notifier_block *unused,
 	case SWITCHDEV_FDB_DEL_TO_DEVICE: /* fall through */
 	case SWITCHDEV_FDB_ADD_TO_BRIDGE: /* fall through */
 	case SWITCHDEV_FDB_DEL_TO_BRIDGE:
+		fdb_info = container_of(info,
+					struct switchdev_notifier_fdb_info,
+					info);
 		INIT_WORK(&switchdev_work->work,
 			  mlxsw_sp_switchdev_bridge_fdb_event_work);
 		memcpy(&switchdev_work->fdb_info, ptr,
-- 
2.17.1

[PATCH net-next 05/19] mlxsw: spectrum: Move L3 protocol and address definitions to global header file

[Ido Schimmel]

The L3 protocol and address definitions are going to be used by the NVE
code, so move them to the global header file from the one private to the
router.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/spectrum.h        | 11 +++++++++++
 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.h | 11 -----------
 2 files changed, 11 insertions(+), 11 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum.h b/drivers/net/ethernet/mellanox/mlxsw/spectrum.h
index 206ecc69b51c..534a8be6a6db 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum.h
@@ -383,6 +383,17 @@ static inline void mlxsw_sp_port_dcb_fini(struct mlxsw_sp_port *mlxsw_sp_port)
 #endif
 
 /* spectrum_router.c */
+enum mlxsw_sp_l3proto {
+	MLXSW_SP_L3_PROTO_IPV4,
+	MLXSW_SP_L3_PROTO_IPV6,
+#define MLXSW_SP_L3_PROTO_MAX	(MLXSW_SP_L3_PROTO_IPV6 + 1)
+};
+
+union mlxsw_sp_l3addr {
+	__be32 addr4;
+	struct in6_addr addr6;
+};
+
 int mlxsw_sp_router_init(struct mlxsw_sp *mlxsw_sp);
 void mlxsw_sp_router_fini(struct mlxsw_sp *mlxsw_sp);
 int mlxsw_sp_netdevice_router_port_event(struct net_device *dev);
diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.h b/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.h
index 354cb0834f3a..3dbafdeaab2b 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum_router.h
@@ -7,17 +7,6 @@
 #include "spectrum.h"
 #include "reg.h"
 
-enum mlxsw_sp_l3proto {
-	MLXSW_SP_L3_PROTO_IPV4,
-	MLXSW_SP_L3_PROTO_IPV6,
-#define MLXSW_SP_L3_PROTO_MAX	(MLXSW_SP_L3_PROTO_IPV6 + 1)
-};
-
-union mlxsw_sp_l3addr {
-	__be32 addr4;
-	struct in6_addr addr6;
-};
-
 struct mlxsw_sp_rif_ipip_lb;
 struct mlxsw_sp_rif_ipip_lb_config {
 	enum mlxsw_reg_ritr_loopback_ipip_type lb_ipipt;
-- 
2.17.1

[PATCH net-next 06/19] mlxsw: spectrum: Add a new type of KVD linear record

[Ido Schimmel]

When the device needs to flood an overlay packet to remote VTEPs it
retrieves a pointer to the head of a linked-list of records that store
the IP addresses of these VTEPs.

These records are stored in the KVD linear memory and configured via the
Tunneling NVE Underlay Multicast Table (TNUMT) register.

Add a new KVD linear entry type for these records, so that we will be
able to allocate and free them.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/spectrum.h       | 2 ++
 drivers/net/ethernet/mellanox/mlxsw/spectrum2_kvdl.c | 1 +
 2 files changed, 3 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum.h b/drivers/net/ethernet/mellanox/mlxsw/spectrum.h
index 534a8be6a6db..1f68ac2a20f4 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum.h
@@ -438,6 +438,7 @@ enum mlxsw_sp_kvdl_entry_type {
 	MLXSW_SP_KVDL_ENTRY_TYPE_ACTSET,
 	MLXSW_SP_KVDL_ENTRY_TYPE_PBS,
 	MLXSW_SP_KVDL_ENTRY_TYPE_MCRIGR,
+	MLXSW_SP_KVDL_ENTRY_TYPE_TNUMT,
 };
 
 static inline unsigned int
@@ -448,6 +449,7 @@ mlxsw_sp_kvdl_entry_size(enum mlxsw_sp_kvdl_entry_type type)
 	case MLXSW_SP_KVDL_ENTRY_TYPE_ACTSET: /* fall through */
 	case MLXSW_SP_KVDL_ENTRY_TYPE_PBS: /* fall through */
 	case MLXSW_SP_KVDL_ENTRY_TYPE_MCRIGR: /* fall through */
+	case MLXSW_SP_KVDL_ENTRY_TYPE_TNUMT: /* fall through */
 	default:
 		return 1;
 	}
diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum2_kvdl.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum2_kvdl.c
index 68c8b148bef2..8d14770766b4 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum2_kvdl.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum2_kvdl.c
@@ -35,6 +35,7 @@ static const struct mlxsw_sp2_kvdl_part_info mlxsw_sp2_kvdl_parts_info[] = {
 				 MAX_KVD_ACTION_SETS),
 	MLXSW_SP2_KVDL_PART_INFO(PBS, 0x24, KVD_SIZE, KVD_SIZE),
 	MLXSW_SP2_KVDL_PART_INFO(MCRIGR, 0x26, KVD_SIZE, KVD_SIZE),
+	MLXSW_SP2_KVDL_PART_INFO(TNUMT, 0x29, KVD_SIZE, KVD_SIZE),
 };
 
 #define MLXSW_SP2_KVDL_PARTS_INFO_LEN ARRAY_SIZE(mlxsw_sp2_kvdl_parts_info)
-- 
2.17.1

[PATCH net-next 07/19] mlxsw: reg: Extend FDB flush types for NVE

[Ido Schimmel]

The device has the ability to flush all the FDB records that perform NVE
encapsulation or only a subset of these with a specific filtering
identifier (FID).

Expose these types so that they could be used by subsequent patches
where we need to flush the FDB records when an NVE device is unlinked
from a bridge (FID).

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index df81e0a1eb64..a0441f3d4284 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -1069,6 +1069,8 @@ enum mlxsw_reg_sfdf_flush_type {
 	MLXSW_REG_SFDF_FLUSH_PER_PORT_AND_FID,
 	MLXSW_REG_SFDF_FLUSH_PER_LAG,
 	MLXSW_REG_SFDF_FLUSH_PER_LAG_AND_FID,
+	MLXSW_REG_SFDF_FLUSH_PER_NVE,
+	MLXSW_REG_SFDF_FLUSH_PER_NVE_AND_FID,
 };
 
 /* reg_sfdf_flush_type
@@ -1079,6 +1081,10 @@ enum mlxsw_reg_sfdf_flush_type {
  * 3 - All FID dynamic entries pointing to port are flushed.
  * 4 - All dynamic entries pointing to LAG are flushed.
  * 5 - All FID dynamic entries pointing to LAG are flushed.
+ * 6 - All entries of type "Unicast Tunnel" or "Multicast Tunnel" are
+ *     flushed.
+ * 7 - All entries of type "Unicast Tunnel" or "Multicast Tunnel" are
+ *     flushed, per FID.
  * Access: RW
  */
 MLXSW_ITEM32(reg, sfdf, flush_type, 0x04, 28, 4);
-- 
2.17.1

[PATCH net-next 08/19] mlxsw: spectrum: Seed LAG hash function

[Ido Schimmel]

Currently, the seed of the LAG hash function is always set to 0, which
means it is identical across all switches. Instead, use a random number.

This is especially important now that VxLAN is supported, as the LAG
hash function is used to calculate the UDP source port of the
encapsulated packet.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h      | 9 ++++++++-
 drivers/net/ethernet/mellanox/mlxsw/spectrum.c | 5 ++++-
 2 files changed, 12 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index a0441f3d4284..4988d24a628c 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -1321,12 +1321,19 @@ MLXSW_ITEM32(reg, slcr, type, 0x00, 0, 4);
  */
 MLXSW_ITEM32(reg, slcr, lag_hash, 0x04, 0, 20);
 
-static inline void mlxsw_reg_slcr_pack(char *payload, u16 lag_hash)
+/* reg_slcr_seed
+ * LAG seed value. The seed is the same for all ports.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, slcr, seed, 0x08, 0, 32);
+
+static inline void mlxsw_reg_slcr_pack(char *payload, u16 lag_hash, u32 seed)
 {
 	MLXSW_REG_ZERO(slcr, payload);
 	mlxsw_reg_slcr_pp_set(payload, MLXSW_REG_SLCR_PP_GLOBAL);
 	mlxsw_reg_slcr_type_set(payload, MLXSW_REG_SLCR_TYPE_CRC);
 	mlxsw_reg_slcr_lag_hash_set(payload, lag_hash);
+	mlxsw_reg_slcr_seed_set(payload, seed);
 }
 
 /* SLCOR - Switch LAG Collector Register
diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
index 2b14fd0dcc42..d42980df57b7 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
@@ -21,6 +21,7 @@
 #include <linux/dcbnl.h>
 #include <linux/inetdevice.h>
 #include <linux/netlink.h>
+#include <linux/random.h>
 #include <net/switchdev.h>
 #include <net/pkt_cls.h>
 #include <net/tc_act/tc_mirred.h>
@@ -3666,8 +3667,10 @@ static void mlxsw_sp_traps_fini(struct mlxsw_sp *mlxsw_sp)
 static int mlxsw_sp_lag_init(struct mlxsw_sp *mlxsw_sp)
 {
 	char slcr_pl[MLXSW_REG_SLCR_LEN];
+	u32 seed;
 	int err;
 
+	get_random_bytes(&seed, sizeof(seed));
 	mlxsw_reg_slcr_pack(slcr_pl, MLXSW_REG_SLCR_LAG_HASH_SMAC |
 				     MLXSW_REG_SLCR_LAG_HASH_DMAC |
 				     MLXSW_REG_SLCR_LAG_HASH_ETHERTYPE |
@@ -3676,7 +3679,7 @@ static int mlxsw_sp_lag_init(struct mlxsw_sp *mlxsw_sp)
 				     MLXSW_REG_SLCR_LAG_HASH_DIP |
 				     MLXSW_REG_SLCR_LAG_HASH_SPORT |
 				     MLXSW_REG_SLCR_LAG_HASH_DPORT |
-				     MLXSW_REG_SLCR_LAG_HASH_IPPROTO);
+				     MLXSW_REG_SLCR_LAG_HASH_IPPROTO, seed);
 	err = mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(slcr), slcr_pl);
 	if (err)
 		return err;
-- 
2.17.1

[PATCH net-next 09/19] mlxsw: reg: Add Tunneling NVE General Configuration Register

[Ido Schimmel]

This register configures global NVE configuration such as source IP of
the NVE tunnel and UDP source port calculation.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h | 185 ++++++++++++++++++++++
 1 file changed, 185 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index 4988d24a628c..3b58f1013677 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -8292,6 +8292,190 @@ static inline void mlxsw_reg_mgpc_pack(char *payload, u32 counter_index,
 	mlxsw_reg_mgpc_opcode_set(payload, opcode);
 }
 
+/* TNGCR - Tunneling NVE General Configuration Register
+ * ----------------------------------------------------
+ * The TNGCR register is used for setting up the NVE Tunneling configuration.
+ */
+#define MLXSW_REG_TNGCR_ID 0xA001
+#define MLXSW_REG_TNGCR_LEN 0x44
+
+MLXSW_REG_DEFINE(tngcr, MLXSW_REG_TNGCR_ID, MLXSW_REG_TNGCR_LEN);
+
+enum mlxsw_reg_tngcr_type {
+	MLXSW_REG_TNGCR_TYPE_VXLAN,
+	MLXSW_REG_TNGCR_TYPE_VXLAN_GPE,
+	MLXSW_REG_TNGCR_TYPE_GENEVE,
+	MLXSW_REG_TNGCR_TYPE_NVGRE,
+};
+
+/* reg_tngcr_type
+ * Tunnel type for encapsulation and decapsulation. The types are mutually
+ * exclusive.
+ * Note: For Spectrum the NVE parsing must be enabled in MPRS.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, type, 0x00, 0, 4);
+
+/* reg_tngcr_nve_valid
+ * The VTEP is valid. Allows adding FDB entries for tunnel encapsulation.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_valid, 0x04, 31, 1);
+
+/* reg_tngcr_nve_ttl_uc
+ * The TTL for NVE tunnel encapsulation underlay unicast packets.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_ttl_uc, 0x04, 0, 8);
+
+/* reg_tngcr_nve_ttl_mc
+ * The TTL for NVE tunnel encapsulation underlay multicast packets.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_ttl_mc, 0x08, 0, 8);
+
+enum {
+	/* Do not copy flow label. Calculate flow label using nve_flh. */
+	MLXSW_REG_TNGCR_FL_NO_COPY,
+	/* Copy flow label from inner packet if packet is IPv6 and
+	 * encapsulation is by IPv6. Otherwise, calculate flow label using
+	 * nve_flh.
+	 */
+	MLXSW_REG_TNGCR_FL_COPY,
+};
+
+/* reg_tngcr_nve_flc
+ * For NVE tunnel encapsulation: Flow label copy from inner packet.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_flc, 0x0C, 25, 1);
+
+enum {
+	/* Flow label is static. In Spectrum this means '0'. Spectrum-2
+	 * uses {nve_fl_prefix, nve_fl_suffix}.
+	 */
+	MLXSW_REG_TNGCR_FL_NO_HASH,
+	/* 8 LSBs of the flow label are calculated from ECMP hash of the
+	 * inner packet. 12 MSBs are configured by nve_fl_prefix.
+	 */
+	MLXSW_REG_TNGCR_FL_HASH,
+};
+
+/* reg_tngcr_nve_flh
+ * NVE flow label hash.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_flh, 0x0C, 24, 1);
+
+/* reg_tngcr_nve_fl_prefix
+ * NVE flow label prefix. Constant 12 MSBs of the flow label.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_fl_prefix, 0x0C, 8, 12);
+
+/* reg_tngcr_nve_fl_suffix
+ * NVE flow label suffix. Constant 8 LSBs of the flow label.
+ * Reserved when nve_flh=1 and for Spectrum.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_fl_suffix, 0x0C, 0, 8);
+
+enum {
+	/* Source UDP port is fixed (default '0') */
+	MLXSW_REG_TNGCR_UDP_SPORT_NO_HASH,
+	/* Source UDP port is calculated based on hash */
+	MLXSW_REG_TNGCR_UDP_SPORT_HASH,
+};
+
+/* reg_tngcr_nve_udp_sport_type
+ * NVE UDP source port type.
+ * Spectrum uses LAG hash (SLCRv2). Spectrum-2 uses ECMP hash (RECRv2).
+ * When the source UDP port is calculated based on hash, then the 8 LSBs
+ * are calculated from hash the 8 MSBs are configured by
+ * nve_udp_sport_prefix.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_udp_sport_type, 0x10, 24, 1);
+
+/* reg_tngcr_nve_udp_sport_prefix
+ * NVE UDP source port prefix. Constant 8 MSBs of the UDP source port.
+ * Reserved when NVE type is NVGRE.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_udp_sport_prefix, 0x10, 8, 8);
+
+/* reg_tngcr_nve_group_size_mc
+ * The amount of sequential linked lists of MC entries. The first linked
+ * list is configured by SFD.underlay_mc_ptr.
+ * Valid values: 1, 2, 4, 8, 16, 32, 64
+ * The linked list are configured by TNUMT.
+ * The hash is set by LAG hash.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_group_size_mc, 0x18, 0, 8);
+
+/* reg_tngcr_nve_group_size_flood
+ * The amount of sequential linked lists of flooding entries. The first
+ * linked list is configured by SFMR.nve_tunnel_flood_ptr
+ * Valid values: 1, 2, 4, 8, 16, 32, 64
+ * The linked list are configured by TNUMT.
+ * The hash is set by LAG hash.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, nve_group_size_flood, 0x1C, 0, 8);
+
+/* reg_tngcr_learn_enable
+ * During decapsulation, whether to learn from NVE port.
+ * Reserved when Spectrum-2. See TNPC.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, learn_enable, 0x20, 31, 1);
+
+/* reg_tngcr_underlay_virtual_router
+ * Underlay virtual router.
+ * Reserved when Spectrum-2.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, underlay_virtual_router, 0x20, 0, 16);
+
+/* reg_tngcr_underlay_rif
+ * Underlay ingress router interface. RIF type should be loopback generic.
+ * Reserved when Spectrum.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, underlay_rif, 0x24, 0, 16);
+
+/* reg_tngcr_usipv4
+ * Underlay source IPv4 address of the NVE.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tngcr, usipv4, 0x28, 0, 32);
+
+/* reg_tngcr_usipv6
+ * Underlay source IPv6 address of the NVE. For Spectrum, must not be
+ * modified under traffic of NVE tunneling encapsulation.
+ * Access: RW
+ */
+MLXSW_ITEM_BUF(reg, tngcr, usipv6, 0x30, 16);
+
+static inline void mlxsw_reg_tngcr_pack(char *payload,
+					enum mlxsw_reg_tngcr_type type,
+					bool valid, u8 ttl)
+{
+	MLXSW_REG_ZERO(tngcr, payload);
+	mlxsw_reg_tngcr_type_set(payload, type);
+	mlxsw_reg_tngcr_nve_valid_set(payload, valid);
+	mlxsw_reg_tngcr_nve_ttl_uc_set(payload, ttl);
+	mlxsw_reg_tngcr_nve_ttl_mc_set(payload, ttl);
+	mlxsw_reg_tngcr_nve_flc_set(payload, MLXSW_REG_TNGCR_FL_NO_COPY);
+	mlxsw_reg_tngcr_nve_flh_set(payload, 0);
+	mlxsw_reg_tngcr_nve_udp_sport_type_set(payload,
+					       MLXSW_REG_TNGCR_UDP_SPORT_HASH);
+	mlxsw_reg_tngcr_nve_udp_sport_prefix_set(payload, 0);
+	mlxsw_reg_tngcr_nve_group_size_mc_set(payload, 1);
+	mlxsw_reg_tngcr_nve_group_size_flood_set(payload, 1);
+}
+
 /* TIGCR - Tunneling IPinIP General Configuration Register
  * -------------------------------------------------------
  * The TIGCR register is used for setting up the IPinIP Tunnel configuration.
@@ -8841,6 +9025,7 @@ static const struct mlxsw_reg_info *mlxsw_reg_infos[] = {
 	MLXSW_REG(mcc),
 	MLXSW_REG(mcda),
 	MLXSW_REG(mgpc),
+	MLXSW_REG(tngcr),
 	MLXSW_REG(tigcr),
 	MLXSW_REG(sbpr),
 	MLXSW_REG(sbcm),
-- 
2.17.1

[PATCH net-next 10/19] mlxsw: reg: Add Tunnel Port Configuration Register

[Ido Schimmel]

This register enables / disables learning on different types of tunnel
ports (e.g., NVE, VPLS).

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h | 46 +++++++++++++++++++++++
 1 file changed, 46 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index 3b58f1013677..de97764a71b2 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -8476,6 +8476,51 @@ static inline void mlxsw_reg_tngcr_pack(char *payload,
 	mlxsw_reg_tngcr_nve_group_size_flood_set(payload, 1);
 }
 
+/* TNPC - Tunnel Port Configuration Register
+ * -----------------------------------------
+ * The TNPC register is used for tunnel port configuration.
+ * Reserved when Spectrum.
+ */
+#define MLXSW_REG_TNPC_ID 0xA020
+#define MLXSW_REG_TNPC_LEN 0x18
+
+MLXSW_REG_DEFINE(tnpc, MLXSW_REG_TNPC_ID, MLXSW_REG_TNPC_LEN);
+
+enum mlxsw_reg_tnpc_tunnel_port {
+	MLXSW_REG_TNPC_TUNNEL_PORT_NVE,
+	MLXSW_REG_TNPC_TUNNEL_PORT_VPLS,
+	MLXSW_REG_TNPC_TUNNEL_FLEX_TUNNEL0,
+	MLXSW_REG_TNPC_TUNNEL_FLEX_TUNNEL1,
+};
+
+/* reg_tnpc_tunnel_port
+ * Tunnel port.
+ * Access: Index
+ */
+MLXSW_ITEM32(reg, tnpc, tunnel_port, 0x00, 0, 4);
+
+/* reg_tnpc_learn_enable_v6
+ * During IPv6 underlay decapsulation, whether to learn from tunnel port.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tnpc, learn_enable_v6, 0x04, 1, 1);
+
+/* reg_tnpc_learn_enable_v4
+ * During IPv4 underlay decapsulation, whether to learn from tunnel port.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tnpc, learn_enable_v4, 0x04, 0, 1);
+
+static inline void mlxsw_reg_tnpc_pack(char *payload,
+				       enum mlxsw_reg_tnpc_tunnel_port tport,
+				       bool learn_enable)
+{
+	MLXSW_REG_ZERO(tnpc, payload);
+	mlxsw_reg_tnpc_tunnel_port_set(payload, tport);
+	mlxsw_reg_tnpc_learn_enable_v4_set(payload, learn_enable);
+	mlxsw_reg_tnpc_learn_enable_v6_set(payload, learn_enable);
+}
+
 /* TIGCR - Tunneling IPinIP General Configuration Register
  * -------------------------------------------------------
  * The TIGCR register is used for setting up the IPinIP Tunnel configuration.
@@ -9026,6 +9071,7 @@ static const struct mlxsw_reg_info *mlxsw_reg_infos[] = {
 	MLXSW_REG(mcda),
 	MLXSW_REG(mgpc),
 	MLXSW_REG(tngcr),
+	MLXSW_REG(tnpc),
 	MLXSW_REG(tigcr),
 	MLXSW_REG(sbpr),
 	MLXSW_REG(sbcm),
-- 
2.17.1

[PATCH net-next 11/19] mlxsw: reg: Add Tunneling NVE Underlay Multicast Table Register

[Ido Schimmel]

This register builds the linked list of underlay destination IPs used
for BUM traffic on the overlay.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h | 91 +++++++++++++++++++++++
 1 file changed, 91 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index de97764a71b2..a8cc7a58c390 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -8476,6 +8476,96 @@ static inline void mlxsw_reg_tngcr_pack(char *payload,
 	mlxsw_reg_tngcr_nve_group_size_flood_set(payload, 1);
 }
 
+/* TNUMT - Tunneling NVE Underlay Multicast Table Register
+ * -------------------------------------------------------
+ * The TNUMT register is for building the underlay MC table. It is used
+ * for MC, flooding and BC traffic into the NVE tunnel.
+ */
+#define MLXSW_REG_TNUMT_ID 0xA003
+#define MLXSW_REG_TNUMT_LEN 0x20
+
+MLXSW_REG_DEFINE(tnumt, MLXSW_REG_TNUMT_ID, MLXSW_REG_TNUMT_LEN);
+
+enum mlxsw_reg_tnumt_record_type {
+	MLXSW_REG_TNUMT_RECORD_TYPE_IPV4,
+	MLXSW_REG_TNUMT_RECORD_TYPE_IPV6,
+	MLXSW_REG_TNUMT_RECORD_TYPE_LABEL,
+};
+
+/* reg_tnumt_record_type
+ * Record type.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tnumt, record_type, 0x00, 28, 4);
+
+enum mlxsw_reg_tnumt_tunnel_port {
+	MLXSW_REG_TNUMT_TUNNEL_PORT_NVE,
+	MLXSW_REG_TNUMT_TUNNEL_PORT_VPLS,
+	MLXSW_REG_TNUMT_TUNNEL_FLEX_TUNNEL0,
+	MLXSW_REG_TNUMT_TUNNEL_FLEX_TUNNEL1,
+};
+
+/* reg_tnumt_tunnel_port
+ * Tunnel port.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tnumt, tunnel_port, 0x00, 24, 4);
+
+/* reg_tnumt_underlay_mc_ptr
+ * Index to the underlay multicast table.
+ * For Spectrum the index is to the KVD linear.
+ * Access: Index
+ */
+MLXSW_ITEM32(reg, tnumt, underlay_mc_ptr, 0x00, 0, 24);
+
+/* reg_tnumt_vnext
+ * The next_underlay_mc_ptr is valid.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tnumt, vnext, 0x04, 31, 1);
+
+/* reg_tnumt_next_underlay_mc_ptr
+ * The next index to the underlay multicast table.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tnumt, next_underlay_mc_ptr, 0x04, 0, 24);
+
+/* reg_tnumt_record_size
+ * Number of IP addresses in the record.
+ * Range is 1..cap_max_nve_mc_entries_ipv{4,6}
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tnumt, record_size, 0x08, 0, 3);
+
+/* reg_tnumt_udip
+ * The underlay IPv4 addresses. udip[i] is reserved if i >= size
+ * Access: RW
+ */
+MLXSW_ITEM32_INDEXED(reg, tnumt, udip, 0x0C, 0, 32, 0x04, 0x00, false);
+
+/* reg_tnumt_udip_ptr
+ * The pointer to the underlay IPv6 addresses. udip_ptr[i] is reserved if
+ * i >= size. The IPv6 addresses are configured by RIPS.
+ * Access: RW
+ */
+MLXSW_ITEM32_INDEXED(reg, tnumt, udip_ptr, 0x0C, 0, 24, 0x04, 0x00, false);
+
+static inline void mlxsw_reg_tnumt_pack(char *payload,
+					enum mlxsw_reg_tnumt_record_type type,
+					enum mlxsw_reg_tnumt_tunnel_port tport,
+					u32 underlay_mc_ptr, bool vnext,
+					u32 next_underlay_mc_ptr,
+					u8 record_size)
+{
+	MLXSW_REG_ZERO(tnumt, payload);
+	mlxsw_reg_tnumt_record_type_set(payload, type);
+	mlxsw_reg_tnumt_tunnel_port_set(payload, tport);
+	mlxsw_reg_tnumt_underlay_mc_ptr_set(payload, underlay_mc_ptr);
+	mlxsw_reg_tnumt_vnext_set(payload, vnext);
+	mlxsw_reg_tnumt_next_underlay_mc_ptr_set(payload, next_underlay_mc_ptr);
+	mlxsw_reg_tnumt_record_size_set(payload, record_size);
+}
+
 /* TNPC - Tunnel Port Configuration Register
  * -----------------------------------------
  * The TNPC register is used for tunnel port configuration.
@@ -9071,6 +9161,7 @@ static const struct mlxsw_reg_info *mlxsw_reg_infos[] = {
 	MLXSW_REG(mcda),
 	MLXSW_REG(mgpc),
 	MLXSW_REG(tngcr),
+	MLXSW_REG(tnumt),
 	MLXSW_REG(tnpc),
 	MLXSW_REG(tigcr),
 	MLXSW_REG(sbpr),
-- 
2.17.1

[PATCH net-next 12/19] mlxsw: reg: Add Tunneling NVE Encapsulation ECN Mapping Register

[Ido Schimmel]

This register performs mapping from overlay ECN to underlay ECN during
NVE encapsulation.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h | 31 +++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index a8cc7a58c390..aabba7360050 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -8566,6 +8566,36 @@ static inline void mlxsw_reg_tnumt_pack(char *payload,
 	mlxsw_reg_tnumt_record_size_set(payload, record_size);
 }
 
+/* TNEEM - Tunneling NVE Encapsulation ECN Mapping Register
+ * --------------------------------------------------------
+ * The TNEEM register maps ECN of the IP header at the ingress to the
+ * encapsulation to the ECN of the underlay network.
+ */
+#define MLXSW_REG_TNEEM_ID 0xA012
+#define MLXSW_REG_TNEEM_LEN 0x0C
+
+MLXSW_REG_DEFINE(tneem, MLXSW_REG_TNEEM_ID, MLXSW_REG_TNEEM_LEN);
+
+/* reg_tneem_overlay_ecn
+ * ECN of the IP header in the overlay network.
+ * Access: Index
+ */
+MLXSW_ITEM32(reg, tneem, overlay_ecn, 0x04, 24, 2);
+
+/* reg_tneem_underlay_ecn
+ * ECN of the IP header in the underlay network.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tneem, underlay_ecn, 0x04, 16, 2);
+
+static inline void mlxsw_reg_tneem_pack(char *payload, u8 overlay_ecn,
+					u8 underlay_ecn)
+{
+	MLXSW_REG_ZERO(tneem, payload);
+	mlxsw_reg_tneem_overlay_ecn_set(payload, overlay_ecn);
+	mlxsw_reg_tneem_underlay_ecn_set(payload, underlay_ecn);
+}
+
 /* TNPC - Tunnel Port Configuration Register
  * -----------------------------------------
  * The TNPC register is used for tunnel port configuration.
@@ -9162,6 +9192,7 @@ static const struct mlxsw_reg_info *mlxsw_reg_infos[] = {
 	MLXSW_REG(mgpc),
 	MLXSW_REG(tngcr),
 	MLXSW_REG(tnumt),
+	MLXSW_REG(tneem),
 	MLXSW_REG(tnpc),
 	MLXSW_REG(tigcr),
 	MLXSW_REG(sbpr),
-- 
2.17.1

[PATCH net-next 13/19] mlxsw: reg: Add Tunneling NVE Decapsulation ECN Mapping Register

[Ido Schimmel]

This register configures the actions that are done during NVE
decapsulation based on the ECN bits.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h | 57 +++++++++++++++++++++++
 1 file changed, 57 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index aabba7360050..915a6e241168 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -8596,6 +8596,62 @@ static inline void mlxsw_reg_tneem_pack(char *payload, u8 overlay_ecn,
 	mlxsw_reg_tneem_underlay_ecn_set(payload, underlay_ecn);
 }
 
+/* TNDEM - Tunneling NVE Decapsulation ECN Mapping Register
+ * --------------------------------------------------------
+ * The TNDEM register configures the actions that are done in the
+ * decapsulation.
+ */
+#define MLXSW_REG_TNDEM_ID 0xA013
+#define MLXSW_REG_TNDEM_LEN 0x0C
+
+MLXSW_REG_DEFINE(tndem, MLXSW_REG_TNDEM_ID, MLXSW_REG_TNDEM_LEN);
+
+/* reg_tndem_underlay_ecn
+ * ECN field of the IP header in the underlay network.
+ * Access: Index
+ */
+MLXSW_ITEM32(reg, tndem, underlay_ecn, 0x04, 24, 2);
+
+/* reg_tndem_overlay_ecn
+ * ECN field of the IP header in the overlay network.
+ * Access: Index
+ */
+MLXSW_ITEM32(reg, tndem, overlay_ecn, 0x04, 16, 2);
+
+/* reg_tndem_eip_ecn
+ * Egress IP ECN. ECN field of the IP header of the packet which goes out
+ * from the decapsulation.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tndem, eip_ecn, 0x04, 8, 2);
+
+/* reg_tndem_trap_en
+ * Trap enable:
+ * 0 - No trap due to decap ECN
+ * 1 - Trap enable with trap_id
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tndem, trap_en, 0x08, 28, 4);
+
+/* reg_tndem_trap_id
+ * Trap ID. Either DECAP_ECN0 or DECAP_ECN1.
+ * Reserved when trap_en is '0'.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tndem, trap_id, 0x08, 0, 9);
+
+static inline void mlxsw_reg_tndem_pack(char *payload, u8 underlay_ecn,
+					u8 overlay_ecn, u8 ecn, bool trap_en,
+					u16 trap_id)
+{
+	MLXSW_REG_ZERO(tndem, payload);
+	mlxsw_reg_tndem_underlay_ecn_set(payload, underlay_ecn);
+	mlxsw_reg_tndem_overlay_ecn_set(payload, overlay_ecn);
+	mlxsw_reg_tndem_eip_ecn_set(payload, ecn);
+	mlxsw_reg_tndem_trap_en_set(payload, trap_en);
+	mlxsw_reg_tndem_trap_id_set(payload, trap_id);
+}
+
 /* TNPC - Tunnel Port Configuration Register
  * -----------------------------------------
  * The TNPC register is used for tunnel port configuration.
@@ -9193,6 +9249,7 @@ static const struct mlxsw_reg_info *mlxsw_reg_infos[] = {
 	MLXSW_REG(tngcr),
 	MLXSW_REG(tnumt),
 	MLXSW_REG(tneem),
+	MLXSW_REG(tndem),
 	MLXSW_REG(tnpc),
 	MLXSW_REG(tigcr),
 	MLXSW_REG(sbpr),
-- 
2.17.1

[PATCH net-next 14/19] mlxsw: reg: Add Tunneling NVE QoS Configuration Register

[Ido Schimmel]

The register configures how QoS is set in Encapsulation into the
underlay network.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h | 26 +++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index 915a6e241168..28fe45783824 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -8566,6 +8566,31 @@ static inline void mlxsw_reg_tnumt_pack(char *payload,
 	mlxsw_reg_tnumt_record_size_set(payload, record_size);
 }
 
+/* TNQCR - Tunneling NVE QoS Configuration Register
+ * ------------------------------------------------
+ * The TNQCR register configures how QoS is set in encapsulation into the
+ * underlay network.
+ */
+#define MLXSW_REG_TNQCR_ID 0xA010
+#define MLXSW_REG_TNQCR_LEN 0x0C
+
+MLXSW_REG_DEFINE(tnqcr, MLXSW_REG_TNQCR_ID, MLXSW_REG_TNQCR_LEN);
+
+/* reg_tnqcr_enc_set_dscp
+ * For encapsulation: How to set DSCP field:
+ * 0 - Copy the DSCP from the overlay (inner) IP header to the underlay
+ * (outer) IP header. If there is no IP header, use TNQDR.dscp
+ * 1 - Set the DSCP field as TNQDR.dscp
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tnqcr, enc_set_dscp, 0x04, 28, 1);
+
+static inline void mlxsw_reg_tnqcr_pack(char *payload)
+{
+	MLXSW_REG_ZERO(tnqcr, payload);
+	mlxsw_reg_tnqcr_enc_set_dscp_set(payload, 0);
+}
+
 /* TNEEM - Tunneling NVE Encapsulation ECN Mapping Register
  * --------------------------------------------------------
  * The TNEEM register maps ECN of the IP header at the ingress to the
@@ -9248,6 +9273,7 @@ static const struct mlxsw_reg_info *mlxsw_reg_infos[] = {
 	MLXSW_REG(mgpc),
 	MLXSW_REG(tngcr),
 	MLXSW_REG(tnumt),
+	MLXSW_REG(tnqcr),
 	MLXSW_REG(tneem),
 	MLXSW_REG(tndem),
 	MLXSW_REG(tnpc),
-- 
2.17.1

[PATCH net-next 15/19] mlxsw: reg: Add Tunneling NVE QoS Default Register

[Ido Schimmel]

The TNQDR register configures the default QoS settings for NVE
encapsulation.

It will be used to set the default DSCP of each port to 0, so that when
DSCP is set to inherit and the overlay packet does not have an IP header
the outer DSCP will be set to 0, in accordance with the software data
path.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h | 30 +++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index 28fe45783824..200cbde2350a 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -8591,6 +8591,35 @@ static inline void mlxsw_reg_tnqcr_pack(char *payload)
 	mlxsw_reg_tnqcr_enc_set_dscp_set(payload, 0);
 }
 
+/* TNQDR - Tunneling NVE QoS Default Register
+ * ------------------------------------------
+ * The TNQDR register configures the default QoS settings for NVE
+ * encapsulation.
+ */
+#define MLXSW_REG_TNQDR_ID 0xA011
+#define MLXSW_REG_TNQDR_LEN 0x08
+
+MLXSW_REG_DEFINE(tnqdr, MLXSW_REG_TNQDR_ID, MLXSW_REG_TNQDR_LEN);
+
+/* reg_tnqdr_local_port
+ * Local port number (receive port). CPU port is supported.
+ * Access: Index
+ */
+MLXSW_ITEM32(reg, tnqdr, local_port, 0x00, 16, 8);
+
+/* reg_tnqdr_dscp
+ * For encapsulation, the default DSCP.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, tnqdr, dscp, 0x04, 0, 6);
+
+static inline void mlxsw_reg_tnqdr_pack(char *payload, u8 local_port)
+{
+	MLXSW_REG_ZERO(tnqdr, payload);
+	mlxsw_reg_tnqdr_local_port_set(payload, local_port);
+	mlxsw_reg_tnqdr_dscp_set(payload, 0);
+}
+
 /* TNEEM - Tunneling NVE Encapsulation ECN Mapping Register
  * --------------------------------------------------------
  * The TNEEM register maps ECN of the IP header at the ingress to the
@@ -9274,6 +9303,7 @@ static const struct mlxsw_reg_info *mlxsw_reg_infos[] = {
 	MLXSW_REG(tngcr),
 	MLXSW_REG(tnumt),
 	MLXSW_REG(tnqcr),
+	MLXSW_REG(tnqdr),
 	MLXSW_REG(tneem),
 	MLXSW_REG(tndem),
 	MLXSW_REG(tnpc),
-- 
2.17.1

[PATCH net-next 16/19] mlxsw: reg: Add definition of unicast tunnel record for SFD register

[Ido Schimmel]

Will be used to program the device with FDB records pointing to a NVE
tunnel.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h | 56 +++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index 200cbde2350a..068af0ea7574 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -295,6 +295,7 @@ enum mlxsw_reg_sfd_rec_type {
 	MLXSW_REG_SFD_REC_TYPE_UNICAST = 0x0,
 	MLXSW_REG_SFD_REC_TYPE_UNICAST_LAG = 0x1,
 	MLXSW_REG_SFD_REC_TYPE_MULTICAST = 0x2,
+	MLXSW_REG_SFD_REC_TYPE_UNICAST_TUNNEL = 0xC,
 };
 
 /* reg_sfd_rec_type
@@ -525,6 +526,61 @@ mlxsw_reg_sfd_mc_pack(char *payload, int rec_index,
 	mlxsw_reg_sfd_mc_mid_set(payload, rec_index, mid);
 }
 
+/* reg_sfd_uc_tunnel_uip_msb
+ * When protocol is IPv4, the most significant byte of the underlay IPv4
+ * destination IP.
+ * When protocol is IPv6, reserved.
+ * Access: RW
+ */
+MLXSW_ITEM32_INDEXED(reg, sfd, uc_tunnel_uip_msb, MLXSW_REG_SFD_BASE_LEN, 24,
+		     8, MLXSW_REG_SFD_REC_LEN, 0x08, false);
+
+/* reg_sfd_uc_tunnel_fid
+ * Filtering ID.
+ * Access: Index
+ */
+MLXSW_ITEM32_INDEXED(reg, sfd, uc_tunnel_fid, MLXSW_REG_SFD_BASE_LEN, 0, 16,
+		     MLXSW_REG_SFD_REC_LEN, 0x08, false);
+
+enum mlxsw_reg_sfd_uc_tunnel_protocol {
+	MLXSW_REG_SFD_UC_TUNNEL_PROTOCOL_IPV4,
+	MLXSW_REG_SFD_UC_TUNNEL_PROTOCOL_IPV6,
+};
+
+/* reg_sfd_uc_tunnel_protocol
+ * IP protocol.
+ * Access: RW
+ */
+MLXSW_ITEM32_INDEXED(reg, sfd, uc_tunnel_protocol, MLXSW_REG_SFD_BASE_LEN, 27,
+		     1, MLXSW_REG_SFD_REC_LEN, 0x0C, false);
+
+/* reg_sfd_uc_tunnel_uip_lsb
+ * When protocol is IPv4, the least significant bytes of the underlay
+ * IPv4 destination IP.
+ * When protocol is IPv6, pointer to the underlay IPv6 destination IP
+ * which is configured by RIPS.
+ * Access: RW
+ */
+MLXSW_ITEM32_INDEXED(reg, sfd, uc_tunnel_uip_lsb, MLXSW_REG_SFD_BASE_LEN, 0,
+		     24, MLXSW_REG_SFD_REC_LEN, 0x0C, false);
+
+static inline void
+mlxsw_reg_sfd_uc_tunnel_pack(char *payload, int rec_index,
+			     enum mlxsw_reg_sfd_rec_policy policy,
+			     const char *mac, u16 fid,
+			     enum mlxsw_reg_sfd_rec_action action, u32 uip,
+			     enum mlxsw_reg_sfd_uc_tunnel_protocol proto)
+{
+	mlxsw_reg_sfd_rec_pack(payload, rec_index,
+			       MLXSW_REG_SFD_REC_TYPE_UNICAST_TUNNEL, mac,
+			       action);
+	mlxsw_reg_sfd_rec_policy_set(payload, rec_index, policy);
+	mlxsw_reg_sfd_uc_tunnel_uip_msb_set(payload, rec_index, uip >> 24);
+	mlxsw_reg_sfd_uc_tunnel_uip_lsb_set(payload, rec_index, uip);
+	mlxsw_reg_sfd_uc_tunnel_fid_set(payload, rec_index, fid);
+	mlxsw_reg_sfd_uc_tunnel_protocol_set(payload, rec_index, proto);
+}
+
 /* SFN - Switch FDB Notification Register
  * -------------------------------------------
  * The switch provides notifications on newly learned FDB entries and
-- 
2.17.1

[PATCH net-next 17/19] mlxsw: reg: Add Monitoring Parsing State Register

[Ido Schimmel]

This register is used for setting up the parsing for hash, policy-engine
and routing.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/reg.h | 44 +++++++++++++++++++++++
 1 file changed, 44 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index 068af0ea7574..32cb6718bb17 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -8348,6 +8348,49 @@ static inline void mlxsw_reg_mgpc_pack(char *payload, u32 counter_index,
 	mlxsw_reg_mgpc_opcode_set(payload, opcode);
 }
 
+/* MPRS - Monitoring Parsing State Register
+ * ----------------------------------------
+ * The MPRS register is used for setting up the parsing for hash,
+ * policy-engine and routing.
+ */
+#define MLXSW_REG_MPRS_ID 0x9083
+#define MLXSW_REG_MPRS_LEN 0x14
+
+MLXSW_REG_DEFINE(mprs, MLXSW_REG_MPRS_ID, MLXSW_REG_MPRS_LEN);
+
+/* reg_mprs_parsing_depth
+ * Minimum parsing depth.
+ * Need to enlarge parsing depth according to L3, MPLS, tunnels, ACL
+ * rules, traps, hash, etc. Default is 96 bytes. Reserved when SwitchX-2.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, mprs, parsing_depth, 0x00, 0, 16);
+
+/* reg_mprs_parsing_en
+ * Parsing enable.
+ * Bit 0 - Enable parsing of NVE of types VxLAN, VxLAN-GPE, GENEVE and
+ * NVGRE. Default is enabled. Reserved when SwitchX-2.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, mprs, parsing_en, 0x04, 0, 16);
+
+/* reg_mprs_vxlan_udp_dport
+ * VxLAN UDP destination port.
+ * Used for identifying VxLAN packets and for dport field in
+ * encapsulation. Default is 4789.
+ * Access: RW
+ */
+MLXSW_ITEM32(reg, mprs, vxlan_udp_dport, 0x10, 0, 16);
+
+static inline void mlxsw_reg_mprs_pack(char *payload, u16 parsing_depth,
+				       u16 vxlan_udp_dport)
+{
+	MLXSW_REG_ZERO(mprs, payload);
+	mlxsw_reg_mprs_parsing_depth_set(payload, parsing_depth);
+	mlxsw_reg_mprs_parsing_en_set(payload, true);
+	mlxsw_reg_mprs_vxlan_udp_dport_set(payload, vxlan_udp_dport);
+}
+
 /* TNGCR - Tunneling NVE General Configuration Register
  * ----------------------------------------------------
  * The TNGCR register is used for setting up the NVE Tunneling configuration.
@@ -9356,6 +9399,7 @@ static const struct mlxsw_reg_info *mlxsw_reg_infos[] = {
 	MLXSW_REG(mcc),
 	MLXSW_REG(mcda),
 	MLXSW_REG(mgpc),
+	MLXSW_REG(mprs),
 	MLXSW_REG(tngcr),
 	MLXSW_REG(tnumt),
 	MLXSW_REG(tnqcr),
-- 
2.17.1

[PATCH net-next 18/19] mlxsw: resources: Add NVE resources

[Ido Schimmel]

Add the following resources to be used by the NVE code:
* Number of IPv4 underlay destination IPs in a single TNUMT record
* Number of IPv6 underlay destination IPs in a single TNUMT record

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/resources.h | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/resources.h b/drivers/net/ethernet/mellanox/mlxsw/resources.h
index 79a31de7c825..99b341539870 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/resources.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/resources.h
@@ -46,6 +46,8 @@ enum mlxsw_res_id {
 	MLXSW_RES_ID_MAX_RIFS,
 	MLXSW_RES_ID_MC_ERIF_LIST_ENTRIES,
 	MLXSW_RES_ID_MAX_LPM_TREES,
+	MLXSW_RES_ID_MAX_NVE_MC_ENTRIES_IPV4,
+	MLXSW_RES_ID_MAX_NVE_MC_ENTRIES_IPV6,
 
 	/* Internal resources.
 	 * Determined by the SW, not queried from the HW.
@@ -96,6 +98,8 @@ static u16 mlxsw_res_ids[] = {
 	[MLXSW_RES_ID_MAX_RIFS] = 0x2C02,
 	[MLXSW_RES_ID_MC_ERIF_LIST_ENTRIES] = 0x2C10,
 	[MLXSW_RES_ID_MAX_LPM_TREES] = 0x2C30,
+	[MLXSW_RES_ID_MAX_NVE_MC_ENTRIES_IPV4] = 0x2E02,
+	[MLXSW_RES_ID_MAX_NVE_MC_ENTRIES_IPV6] = 0x2E03,
 };
 
 struct mlxsw_res {
-- 
2.17.1

[PATCH net-next 19/19] mlxsw: spectrum: Add NVE packet traps

[Ido Schimmel]

The DECAP_ECN0 trap will be used to trap packets where the overlay
packet is marked with Non-ECT, but the underlay packet is marked with
either ECT(0), ECT(1) or CE. When trapped, such packets will be counted
as errors by the VxLAN driver and thus provide better visibility.

The NVE_ENCAP_ARP trap will be used to trap ARP packets undergoing NVE
encapsulation. This is needed in order to support E-VPN ARP suppression,
where the Linux bridge does not flood ARP packets through tunnel ports
in case it can answer the ARP request itself.

Note that all the packets trapped via these traps are marked with
'offload_fwd_mark', so as to not be re-flooded by the Linux bridge
through the ASIC ports.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
---
 drivers/net/ethernet/mellanox/mlxsw/spectrum.c | 3 +++
 drivers/net/ethernet/mellanox/mlxsw/trap.h     | 2 ++
 2 files changed, 5 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
index d42980df57b7..ed7e4c4e7403 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
+++ b/drivers/net/ethernet/mellanox/mlxsw/spectrum.c
@@ -3470,6 +3470,7 @@ static const struct mlxsw_listener mlxsw_sp_listener[] = {
 	MLXSW_SP_RXL_MARK(ROUTER_ALERT_IPV4, TRAP_TO_CPU, ROUTER_EXP, false),
 	MLXSW_SP_RXL_MARK(ROUTER_ALERT_IPV6, TRAP_TO_CPU, ROUTER_EXP, false),
 	MLXSW_SP_RXL_MARK(IPIP_DECAP_ERROR, TRAP_TO_CPU, ROUTER_EXP, false),
+	MLXSW_SP_RXL_MARK(DECAP_ECN0, TRAP_TO_CPU, ROUTER_EXP, false),
 	MLXSW_SP_RXL_MARK(IPV4_VRRP, TRAP_TO_CPU, ROUTER_EXP, false),
 	MLXSW_SP_RXL_MARK(IPV6_VRRP, TRAP_TO_CPU, ROUTER_EXP, false),
 	/* PKT Sample trap */
@@ -3483,6 +3484,8 @@ static const struct mlxsw_listener mlxsw_sp_listener[] = {
 	MLXSW_SP_RXL_MARK(RPF, TRAP_TO_CPU, RPF, false),
 	MLXSW_SP_RXL_MARK(ACL1, TRAP_TO_CPU, MULTICAST, false),
 	MLXSW_SP_RXL_MR_MARK(ACL2, TRAP_TO_CPU, MULTICAST, false),
+	/* NVE traps */
+	MLXSW_SP_RXL_MARK(NVE_ENCAP_ARP, TRAP_TO_CPU, ARP, false),
 };
 
 static int mlxsw_sp_cpu_policers_set(struct mlxsw_core *mlxsw_core)
diff --git a/drivers/net/ethernet/mellanox/mlxsw/trap.h b/drivers/net/ethernet/mellanox/mlxsw/trap.h
index 53020724c2f6..6f18f4d3322a 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/trap.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/trap.h
@@ -24,6 +24,7 @@ enum {
 	MLXSW_TRAP_ID_IGMP_V3_REPORT = 0x34,
 	MLXSW_TRAP_ID_PKT_SAMPLE = 0x38,
 	MLXSW_TRAP_ID_FID_MISS = 0x3D,
+	MLXSW_TRAP_ID_DECAP_ECN0 = 0x40,
 	MLXSW_TRAP_ID_ARPBC = 0x50,
 	MLXSW_TRAP_ID_ARPUC = 0x51,
 	MLXSW_TRAP_ID_MTUERROR = 0x52,
@@ -59,6 +60,7 @@ enum {
 	MLXSW_TRAP_ID_IPV6_MC_LINK_LOCAL_DEST = 0x91,
 	MLXSW_TRAP_ID_HOST_MISS_IPV6 = 0x92,
 	MLXSW_TRAP_ID_IPIP_DECAP_ERROR = 0xB1,
+	MLXSW_TRAP_ID_NVE_ENCAP_ARP = 0xBD,
 	MLXSW_TRAP_ID_ROUTER_ALERT_IPV4 = 0xD6,
 	MLXSW_TRAP_ID_ROUTER_ALERT_IPV6 = 0xD7,
 	MLXSW_TRAP_ID_ACL0 = 0x1C0,
-- 
2.17.1

Re: [PATCH net-next 00/19] mlxsw: Preparations for VxLAN support

[David Miller]

From: Ido Schimmel <idosch@mellanox.com>
Date: Thu, 11 Oct 2018 07:47:48 +0000

> This patchset prepares mlxsw for VxLAN support. It contains small and
> mostly non-functional changes.

Series applied, thanks.