[net-next 00/15][pull request] Intel Wired LAN Driver Updates 2019-06-28

[net-next 00/15][pull request] Intel Wired LAN Driver Updates 2019-06-28

[Jeff Kirsher]

This series contains a smorgasbord of updates to many of the Intel
drivers.

Gustavo A. R. Silva updates the ice and iavf drivers to use the
strcut_size() helper where possible.

Miguel increases the pause and refresh time for flow control in the
e1000e driver during reset for certain devices.

Dann Frazier fixes a potential NULL pointer dereference in ixgbe driver
when using non-IPSec enabled devices.

Colin Ian King fixes a potential overflow during a shift in the ixgbe
driver.  Also fixes a potential NULL pointer dereference in the iavf
driver by adding a check.

Venkatesh Srinivas converts the e1000 driver to use dma_wmb() instead of
wmb() for doorbell writes to avoid SFENCEs in the transmit and receive
paths.

Arjan updates the e1000e driver to improve boot time by over 100 msec by
reducing the usleep ranges suring system startup.

Artem updates the igb driver register dump in ethtool, first prepares
the register dump for future additions of registers in the dump, then
secondly, adds the RR2DCDELAY register to the dump.  When dealing with
time-sensitive networks, this register is helpful in determining your
latency from the device to the ring.

Alex fixes the ixgbevf driver to use the current cached link state,
rather than trying to re-check the value from the PF.

Harshitha adds support for MACVLAN offloads in i40e by using channels as
MACVLAN interfaces.

Detlev Casanova updates the e1000e driver to use delayed work instead of
timers to run the watchdog.

Vitaly fixes an issue in e1000e, where when disconnecting and
reconnecting the physical cable connection, the NIC enters a DMoff
state.  This state causes a mismatch in link and duplexing, so check the
PCIm function state and perform a PHY reset when in this state to
resolve the issue.

The following are changes since commit 5cdda5f1d6adde02da591ca2196f20289977dc56:
  ipv4: enable route flushing in network namespaces
and are available in the git repository at:
  git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue 10GbE

Alexander Duyck (1):
  ixgbevf: Use cached link state instead of re-reading the value for
    ethtool

Arjan van de Ven (1):
  e1000e: Reduce boot time by tightening sleep ranges

Artem Bityutskiy (2):
  igb: minor ethool regdump amendment
  igb: add RR2DCDELAY to ethtool registers dump

Colin Ian King (2):
  ixgbe: fix potential u32 overflow on shift
  iavf: fix dereference of null rx_buffer pointer

Dann Frazier (1):
  ixgbe: Avoid NULL pointer dereference with VF on non-IPsec hw

Detlev Casanova (1):
  e1000e: Make watchdog use delayed work

Gustavo A. R. Silva (2):
  ice: Use struct_size() helper
  iavf: use struct_size() helper

Harshitha Ramamurthy (1):
  i40e: Add macvlan support on i40e

Jeff Kirsher (1):
  iavf: Fix up debug print macro

Miguel Bernal Marin (1):
  e1000e: Increase pause and refresh time

Venkatesh Srinivas (1):
  e1000: Use dma_wmb() instead of wmb() before doorbell writes

Vitaly Lifshits (1):
  e1000e: PCIm function state support

 drivers/net/ethernet/intel/e1000/e1000_main.c |   6 +-
 .../net/ethernet/intel/e1000e/80003es2lan.c   |   2 +-
 drivers/net/ethernet/intel/e1000e/82571.c     |   2 +-
 drivers/net/ethernet/intel/e1000e/defines.h   |   3 +
 drivers/net/ethernet/intel/e1000e/e1000.h     |   5 +-
 drivers/net/ethernet/intel/e1000e/ethtool.c   |  14 +-
 drivers/net/ethernet/intel/e1000e/ich8lan.c   |  20 +-
 drivers/net/ethernet/intel/e1000e/mac.c       |   2 +-
 drivers/net/ethernet/intel/e1000e/netdev.c    |  90 ++--
 drivers/net/ethernet/intel/e1000e/nvm.c       |   2 +-
 drivers/net/ethernet/intel/i40e/i40e.h        |  27 +
 drivers/net/ethernet/intel/i40e/i40e_main.c   | 497 +++++++++++++++++-
 drivers/net/ethernet/intel/iavf/iavf_osdep.h  |  10 +-
 drivers/net/ethernet/intel/iavf/iavf_txrx.c   |   6 +-
 .../net/ethernet/intel/iavf/iavf_virtchnl.c   |  37 +-
 drivers/net/ethernet/intel/ice/ice_sched.c    |   4 +-
 drivers/net/ethernet/intel/igb/e1000_regs.h   |   2 +
 drivers/net/ethernet/intel/igb/igb_ethtool.c  |  75 +--
 .../net/ethernet/intel/ixgbe/ixgbe_ipsec.c    |   3 +
 drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c  |  14 +-
 drivers/net/ethernet/intel/ixgbevf/ethtool.c  |  10 +-
 21 files changed, 686 insertions(+), 145 deletions(-)

-- 
2.21.0

[net-next 01/15] ice: Use struct_size() helper

[Jeff Kirsher]

From: "Gustavo A. R. Silva" <gustavo@embeddedor.com>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

size = struct_size(instance, entry, count);

This code was detected with the help of Coccinelle.

Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ice/ice_sched.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/ice/ice_sched.c b/drivers/net/ethernet/intel/ice/ice_sched.c
index 8d49f83be7a5..2a232504379d 100644
--- a/drivers/net/ethernet/intel/ice/ice_sched.c
+++ b/drivers/net/ethernet/intel/ice/ice_sched.c
@@ -683,10 +683,10 @@ ice_sched_add_elems(struct ice_port_info *pi, struct ice_sched_node *tc_node,
 	u16 i, num_groups_added = 0;
 	enum ice_status status = 0;
 	struct ice_hw *hw = pi->hw;
-	u16 buf_size;
+	size_t buf_size;
 	u32 teid;
 
-	buf_size = sizeof(*buf) + sizeof(*buf->generic) * (num_nodes - 1);
+	buf_size = struct_size(buf, generic, num_nodes - 1);
 	buf = devm_kzalloc(ice_hw_to_dev(hw), buf_size, GFP_KERNEL);
 	if (!buf)
 		return ICE_ERR_NO_MEMORY;
-- 
2.21.0

[net-next 02/15] e1000e: Increase pause and refresh time

[Jeff Kirsher]

From: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>

Suggested-by: Tim Pepper <timothy.c.pepper@linux.intel.com>
Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index b081a1ef6859..2454a3757bf3 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -4046,12 +4046,12 @@ void e1000e_reset(struct e1000_adapter *adapter)
 	case e1000_pch_lpt:
 	case e1000_pch_spt:
 	case e1000_pch_cnp:
-		fc->refresh_time = 0x0400;
+		fc->refresh_time = 0xFFFF;
+		fc->pause_time = 0xFFFF;
 
 		if (adapter->netdev->mtu <= ETH_DATA_LEN) {
 			fc->high_water = 0x05C20;
 			fc->low_water = 0x05048;
-			fc->pause_time = 0x0650;
 			break;
 		}
 
-- 
2.21.0

[net-next 03/15] ixgbe: Avoid NULL pointer dereference with VF on non-IPsec hw

[Jeff Kirsher]

From: Dann Frazier <dann.frazier@canonical.com>

An ipsec structure will not be allocated if the hardware does not support
offload. Fixes the following Oops:

[  191.045452] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[  191.054232] Mem abort info:
[  191.057014]   ESR = 0x96000004
[  191.060057]   Exception class = DABT (current EL), IL = 32 bits
[  191.065963]   SET = 0, FnV = 0
[  191.069004]   EA = 0, S1PTW = 0
[  191.072132] Data abort info:
[  191.074999]   ISV = 0, ISS = 0x00000004
[  191.078822]   CM = 0, WnR = 0
[  191.081780] user pgtable: 4k pages, 48-bit VAs, pgdp = 0000000043d9e467
[  191.088382] [0000000000000000] pgd=0000000000000000
[  191.093252] Internal error: Oops: 96000004 [#1] SMP
[  191.098119] Modules linked in: vhost_net vhost tap vfio_pci vfio_virqfd vfio_iommu_type1 vfio xt_CHECKSUM iptable_mangle ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ipt_REJECT nf_reject_ipv4 xt_tcpudp bridge stp llc ebtable_filter devlink ebtables ip6table_filter ip6_tables iptable_filter bpfilter ipmi_ssif nls_iso8859_1 input_leds joydev ipmi_si hns_roce_hw_v2 ipmi_devintf hns_roce ipmi_msghandler cppc_cpufreq sch_fq_codel ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 ses enclosure btrfs zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor hid_generic usbhid hid raid6_pq libcrc32c raid1 raid0 multipath linear ixgbevf hibmc_drm ttm
[  191.168607]  drm_kms_helper aes_ce_blk aes_ce_cipher syscopyarea crct10dif_ce sysfillrect ghash_ce qla2xxx sysimgblt sha2_ce sha256_arm64 hisi_sas_v3_hw fb_sys_fops sha1_ce uas nvme_fc mpt3sas ixgbe drm hisi_sas_main nvme_fabrics usb_storage hclge scsi_transport_fc ahci libsas hnae3 raid_class libahci xfrm_algo scsi_transport_sas mdio aes_neon_bs aes_neon_blk crypto_simd cryptd aes_arm64
[  191.202952] CPU: 94 PID: 0 Comm: swapper/94 Not tainted 4.19.0-rc1+ #11
[  191.209553] Hardware name: Huawei D06 /D06, BIOS Hisilicon D06 UEFI RC0 - V1.20.01 04/26/2019
[  191.218064] pstate: 20400089 (nzCv daIf +PAN -UAO)
[  191.222873] pc : ixgbe_ipsec_vf_clear+0x60/0xd0 [ixgbe]
[  191.228093] lr : ixgbe_msg_task+0x2d0/0x1088 [ixgbe]
[  191.233044] sp : ffff000009b3bcd0
[  191.236346] x29: ffff000009b3bcd0 x28: 0000000000000000
[  191.241647] x27: ffff000009628000 x26: 0000000000000000
[  191.246946] x25: ffff803f652d7600 x24: 0000000000000004
[  191.252246] x23: ffff803f6a718900 x22: 0000000000000000
[  191.257546] x21: 0000000000000000 x20: 0000000000000000
[  191.262845] x19: 0000000000000000 x18: 0000000000000000
[  191.268144] x17: 0000000000000000 x16: 0000000000000000
[  191.273443] x15: 0000000000000000 x14: 0000000100000026
[  191.278742] x13: 0000000100000025 x12: ffff8a5f7fbe0df0
[  191.284042] x11: 000000010000000b x10: 0000000000000040
[  191.289341] x9 : 0000000000001100 x8 : ffff803f6a824fd8
[  191.294640] x7 : ffff803f6a825098 x6 : 0000000000000001
[  191.299939] x5 : ffff000000f0ffc0 x4 : 0000000000000000
[  191.305238] x3 : ffff000028c00000 x2 : ffff803f652d7600
[  191.310538] x1 : 0000000000000000 x0 : ffff000000f205f0
[  191.315838] Process swapper/94 (pid: 0, stack limit = 0x00000000addfed5a)
[  191.322613] Call trace:
[  191.325055]  ixgbe_ipsec_vf_clear+0x60/0xd0 [ixgbe]
[  191.329927]  ixgbe_msg_task+0x2d0/0x1088 [ixgbe]
[  191.334536]  ixgbe_msix_other+0x274/0x330 [ixgbe]
[  191.339233]  __handle_irq_event_percpu+0x78/0x270
[  191.343924]  handle_irq_event_percpu+0x40/0x98
[  191.348355]  handle_irq_event+0x50/0xa8
[  191.352180]  handle_fasteoi_irq+0xbc/0x148
[  191.356263]  generic_handle_irq+0x34/0x50
[  191.360259]  __handle_domain_irq+0x68/0xc0
[  191.364343]  gic_handle_irq+0x84/0x180
[  191.368079]  el1_irq+0xe8/0x180
[  191.371208]  arch_cpu_idle+0x30/0x1a8
[  191.374860]  do_idle+0x1dc/0x2a0
[  191.378077]  cpu_startup_entry+0x2c/0x30
[  191.381988]  secondary_start_kernel+0x150/0x1e0
[  191.386506] Code: 6b15003f 54000320 f1404a9f 54000060 (79400260)

Fixes: eda0333ac2930 ("ixgbe: add VF IPsec management")
Signed-off-by: Dann Frazier <dann.frazier@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c
index ff85ce5791a3..31629fc7e820 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c
@@ -842,6 +842,9 @@ void ixgbe_ipsec_vf_clear(struct ixgbe_adapter *adapter, u32 vf)
 	struct ixgbe_ipsec *ipsec = adapter->ipsec;
 	int i;
 
+	if (!ipsec)
+		return;
+
 	/* search rx sa table */
 	for (i = 0; i < IXGBE_IPSEC_MAX_SA_COUNT && ipsec->num_rx_sa; i++) {
 		if (!ipsec->rx_tbl[i].used)
-- 
2.21.0

[net-next 04/15] ixgbe: fix potential u32 overflow on shift

[Jeff Kirsher]

From: Colin Ian King <colin.king@canonical.com>

The u32 variable rem is being shifted using u32 arithmetic however
it is being passed to div_u64 that expects the expression to be a u64.
The 32 bit shift may potentially overflow, so cast rem to a u64 before
shifting to avoid this.  Also remove comment about overflow.

Addresses-Coverity: ("Unintentional integer overflow")
Fixes: cd4583206990 ("ixgbe: implement support for SDP/PPS output on X550 hardware")
Fixes: 68d9676fc04e ("ixgbe: fix PTP SDP pin setup on X540 hardware")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c | 14 ++++----------
 1 file changed, 4 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c
index 2c4d327fcc2e..0be13a90ff79 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ptp.c
@@ -205,11 +205,8 @@ static void ixgbe_ptp_setup_sdp_X540(struct ixgbe_adapter *adapter)
 	 */
 	rem = (NS_PER_SEC - rem);
 
-	/* Adjust the clock edge to align with the next full second. This
-	 * assumes that the cycle counter shift is small enough to avoid
-	 * overflowing when shifting the remainder.
-	 */
-	clock_edge += div_u64((rem << cc->shift), cc->mult);
+	/* Adjust the clock edge to align with the next full second. */
+	clock_edge += div_u64(((u64)rem << cc->shift), cc->mult);
 	trgttiml = (u32)clock_edge;
 	trgttimh = (u32)(clock_edge >> 32);
 
@@ -291,11 +288,8 @@ static void ixgbe_ptp_setup_sdp_X550(struct ixgbe_adapter *adapter)
 	 */
 	rem = (NS_PER_SEC - rem);
 
-	/* Adjust the clock edge to align with the next full second. This
-	 * assumes that the cycle counter shift is small enough to avoid
-	 * overflowing when shifting the remainder.
-	 */
-	clock_edge += div_u64((rem << cc->shift), cc->mult);
+	/* Adjust the clock edge to align with the next full second. */
+	clock_edge += div_u64(((u64)rem << cc->shift), cc->mult);
 
 	/* X550 hardware stores the time in 32bits of 'billions of cycles' and
 	 * 32bits of 'cycles'. There's no guarantee that cycles represents
-- 
2.21.0

[net-next 05/15] e1000: Use dma_wmb() instead of wmb() before doorbell writes

[Jeff Kirsher]

From: Venkatesh Srinivas <venkateshs@google.com>

e1000 writes to doorbells to post transmit descriptors and fill the
receive ring. After writing descriptors to memory but before
writing to doorbells, use dma_wmb() rather than wmb(). wmb() is more
heavyweight than necessary for a device to see descriptor writes.

On x86, this avoids SFENCEs before doorbell writes in both the
Tx and Rx paths. On ARM, this converts DSB ST -> DMB OSHST.

Tested: 82576EB / x86; QEMU (qemu emulates an 8257x)

Signed-off-by: Venkatesh Srinivas <venkateshs@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000/e1000_main.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000/e1000_main.c b/drivers/net/ethernet/intel/e1000/e1000_main.c
index 551de8c2fef2..f703fa58458e 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_main.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_main.c
@@ -3019,7 +3019,7 @@ static void e1000_tx_queue(struct e1000_adapter *adapter,
 	 * applicable for weak-ordered memory model archs,
 	 * such as IA-64).
 	 */
-	wmb();
+	dma_wmb();
 
 	tx_ring->next_to_use = i;
 }
@@ -4540,7 +4540,7 @@ e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
 		 * applicable for weak-ordered memory model archs,
 		 * such as IA-64).
 		 */
-		wmb();
+		dma_wmb();
 		writel(i, adapter->hw.hw_addr + rx_ring->rdt);
 	}
 }
@@ -4655,7 +4655,7 @@ static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
 		 * applicable for weak-ordered memory model archs,
 		 * such as IA-64).
 		 */
-		wmb();
+		dma_wmb();
 		writel(i, hw->hw_addr + rx_ring->rdt);
 	}
 }
-- 
2.21.0

[net-next 06/15] iavf: use struct_size() helper

[Jeff Kirsher]

From: "Gustavo A. R. Silva" <gustavo@embeddedor.com>

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, replace code of the following form:

sizeof(struct virtchnl_ether_addr_list) + (count * sizeof(struct virtchnl_ether_addr))

with:

struct_size(veal, list, count)

and so on...

This code was detected with the help of Coccinelle.

Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 .../net/ethernet/intel/iavf/iavf_virtchnl.c   | 37 ++++++++-----------
 1 file changed, 16 insertions(+), 21 deletions(-)

diff --git a/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c b/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
index cb7c56c5afe6..d49d58a6de80 100644
--- a/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
+++ b/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
@@ -242,7 +242,8 @@ void iavf_configure_queues(struct iavf_adapter *adapter)
 	struct virtchnl_vsi_queue_config_info *vqci;
 	struct virtchnl_queue_pair_info *vqpi;
 	int pairs = adapter->num_active_queues;
-	int i, len, max_frame = IAVF_MAX_RXBUFFER;
+	int i, max_frame = IAVF_MAX_RXBUFFER;
+	size_t len;
 
 	if (adapter->current_op != VIRTCHNL_OP_UNKNOWN) {
 		/* bail because we already have a command pending */
@@ -251,8 +252,7 @@ void iavf_configure_queues(struct iavf_adapter *adapter)
 		return;
 	}
 	adapter->current_op = VIRTCHNL_OP_CONFIG_VSI_QUEUES;
-	len = sizeof(struct virtchnl_vsi_queue_config_info) +
-		       (sizeof(struct virtchnl_queue_pair_info) * pairs);
+	len = struct_size(vqci, qpair, pairs);
 	vqci = kzalloc(len, GFP_KERNEL);
 	if (!vqci)
 		return;
@@ -351,8 +351,9 @@ void iavf_map_queues(struct iavf_adapter *adapter)
 {
 	struct virtchnl_irq_map_info *vimi;
 	struct virtchnl_vector_map *vecmap;
-	int v_idx, q_vectors, len;
 	struct iavf_q_vector *q_vector;
+	int v_idx, q_vectors;
+	size_t len;
 
 	if (adapter->current_op != VIRTCHNL_OP_UNKNOWN) {
 		/* bail because we already have a command pending */
@@ -364,9 +365,7 @@ void iavf_map_queues(struct iavf_adapter *adapter)
 
 	q_vectors = adapter->num_msix_vectors - NONQ_VECS;
 
-	len = sizeof(struct virtchnl_irq_map_info) +
-	      (adapter->num_msix_vectors *
-		sizeof(struct virtchnl_vector_map));
+	len = struct_size(vimi, vecmap, adapter->num_msix_vectors);
 	vimi = kzalloc(len, GFP_KERNEL);
 	if (!vimi)
 		return;
@@ -433,9 +432,10 @@ int iavf_request_queues(struct iavf_adapter *adapter, int num)
 void iavf_add_ether_addrs(struct iavf_adapter *adapter)
 {
 	struct virtchnl_ether_addr_list *veal;
-	int len, i = 0, count = 0;
 	struct iavf_mac_filter *f;
+	int i = 0, count = 0;
 	bool more = false;
+	size_t len;
 
 	if (adapter->current_op != VIRTCHNL_OP_UNKNOWN) {
 		/* bail because we already have a command pending */
@@ -457,15 +457,13 @@ void iavf_add_ether_addrs(struct iavf_adapter *adapter)
 	}
 	adapter->current_op = VIRTCHNL_OP_ADD_ETH_ADDR;
 
-	len = sizeof(struct virtchnl_ether_addr_list) +
-	      (count * sizeof(struct virtchnl_ether_addr));
+	len = struct_size(veal, list, count);
 	if (len > IAVF_MAX_AQ_BUF_SIZE) {
 		dev_warn(&adapter->pdev->dev, "Too many add MAC changes in one request\n");
 		count = (IAVF_MAX_AQ_BUF_SIZE -
 			 sizeof(struct virtchnl_ether_addr_list)) /
 			sizeof(struct virtchnl_ether_addr);
-		len = sizeof(struct virtchnl_ether_addr_list) +
-		      (count * sizeof(struct virtchnl_ether_addr));
+		len = struct_size(veal, list, count);
 		more = true;
 	}
 
@@ -505,8 +503,9 @@ void iavf_del_ether_addrs(struct iavf_adapter *adapter)
 {
 	struct virtchnl_ether_addr_list *veal;
 	struct iavf_mac_filter *f, *ftmp;
-	int len, i = 0, count = 0;
+	int i = 0, count = 0;
 	bool more = false;
+	size_t len;
 
 	if (adapter->current_op != VIRTCHNL_OP_UNKNOWN) {
 		/* bail because we already have a command pending */
@@ -528,15 +527,13 @@ void iavf_del_ether_addrs(struct iavf_adapter *adapter)
 	}
 	adapter->current_op = VIRTCHNL_OP_DEL_ETH_ADDR;
 
-	len = sizeof(struct virtchnl_ether_addr_list) +
-	      (count * sizeof(struct virtchnl_ether_addr));
+	len = struct_size(veal, list, count);
 	if (len > IAVF_MAX_AQ_BUF_SIZE) {
 		dev_warn(&adapter->pdev->dev, "Too many delete MAC changes in one request\n");
 		count = (IAVF_MAX_AQ_BUF_SIZE -
 			 sizeof(struct virtchnl_ether_addr_list)) /
 			sizeof(struct virtchnl_ether_addr);
-		len = sizeof(struct virtchnl_ether_addr_list) +
-		      (count * sizeof(struct virtchnl_ether_addr));
+		len = struct_size(veal, list, count);
 		more = true;
 	}
 	veal = kzalloc(len, GFP_ATOMIC);
@@ -973,7 +970,7 @@ static void iavf_print_link_message(struct iavf_adapter *adapter)
 void iavf_enable_channels(struct iavf_adapter *adapter)
 {
 	struct virtchnl_tc_info *vti = NULL;
-	u16 len;
+	size_t len;
 	int i;
 
 	if (adapter->current_op != VIRTCHNL_OP_UNKNOWN) {
@@ -983,9 +980,7 @@ void iavf_enable_channels(struct iavf_adapter *adapter)
 		return;
 	}
 
-	len = ((adapter->num_tc - 1) * sizeof(struct virtchnl_channel_info)) +
-	       sizeof(struct virtchnl_tc_info);
-
+	len = struct_size(vti, list, adapter->num_tc - 1);
 	vti = kzalloc(len, GFP_KERNEL);
 	if (!vti)
 		return;
-- 
2.21.0

[net-next 07/15] e1000e: Reduce boot time by tightening sleep ranges

[Jeff Kirsher]

From: Arjan van de Ven <arjan@linux.intel.com>

The e1000e driver is a great user of the usleep_range() API,
and has nice ranges that in principle help power management.

However the ranges that are used only during system startup are
very long (and can add easily 100 msec to the boot time) while
the power savings of such long ranges is irrelevant due to the
one-off, boot only, nature of these functions.

This patch shrinks some of the longest ranges to be shorter
(while still using a power friendly 1 msec range); this saves
100msec+ of boot time on my BDW NUCs

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 .../net/ethernet/intel/e1000e/80003es2lan.c   |  2 +-
 drivers/net/ethernet/intel/e1000e/82571.c     |  2 +-
 drivers/net/ethernet/intel/e1000e/ethtool.c   | 14 ++++++-------
 drivers/net/ethernet/intel/e1000e/ich8lan.c   | 20 +++++++++----------
 drivers/net/ethernet/intel/e1000e/mac.c       |  2 +-
 drivers/net/ethernet/intel/e1000e/netdev.c    | 14 ++++++-------
 drivers/net/ethernet/intel/e1000e/nvm.c       |  2 +-
 7 files changed, 28 insertions(+), 28 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index f86d55657959..4b103cca8a39 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -680,7 +680,7 @@ static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
 	ew32(TCTL, E1000_TCTL_PSP);
 	e1e_flush();
 
-	usleep_range(10000, 20000);
+	usleep_range(10000, 11000);
 
 	ctrl = er32(CTRL);
 
diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index b9309302c29e..2c1bab377b2a 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -959,7 +959,7 @@ static s32 e1000_reset_hw_82571(struct e1000_hw *hw)
 	ew32(TCTL, tctl);
 	e1e_flush();
 
-	usleep_range(10000, 20000);
+	usleep_range(10000, 11000);
 
 	/* Must acquire the MDIO ownership before MAC reset.
 	 * Ownership defaults to firmware after a reset.
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 02ebf208f48b..08342698386d 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -1014,7 +1014,7 @@ static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
 	/* Disable all the interrupts */
 	ew32(IMC, 0xFFFFFFFF);
 	e1e_flush();
-	usleep_range(10000, 20000);
+	usleep_range(10000, 11000);
 
 	/* Test each interrupt */
 	for (i = 0; i < 10; i++) {
@@ -1046,7 +1046,7 @@ static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
 			ew32(IMC, mask);
 			ew32(ICS, mask);
 			e1e_flush();
-			usleep_range(10000, 20000);
+			usleep_range(10000, 11000);
 
 			if (adapter->test_icr & mask) {
 				*data = 3;
@@ -1064,7 +1064,7 @@ static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
 		ew32(IMS, mask);
 		ew32(ICS, mask);
 		e1e_flush();
-		usleep_range(10000, 20000);
+		usleep_range(10000, 11000);
 
 		if (!(adapter->test_icr & mask)) {
 			*data = 4;
@@ -1082,7 +1082,7 @@ static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
 			ew32(IMC, ~mask & 0x00007FFF);
 			ew32(ICS, ~mask & 0x00007FFF);
 			e1e_flush();
-			usleep_range(10000, 20000);
+			usleep_range(10000, 11000);
 
 			if (adapter->test_icr) {
 				*data = 5;
@@ -1094,7 +1094,7 @@ static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
 	/* Disable all the interrupts */
 	ew32(IMC, 0xFFFFFFFF);
 	e1e_flush();
-	usleep_range(10000, 20000);
+	usleep_range(10000, 11000);
 
 	/* Unhook test interrupt handler */
 	free_irq(irq, netdev);
@@ -1470,7 +1470,7 @@ static int e1000_set_82571_fiber_loopback(struct e1000_adapter *adapter)
 	 */
 	ew32(SCTL, E1000_SCTL_ENABLE_SERDES_LOOPBACK);
 	e1e_flush();
-	usleep_range(10000, 20000);
+	usleep_range(10000, 11000);
 
 	return 0;
 }
@@ -1584,7 +1584,7 @@ static void e1000_loopback_cleanup(struct e1000_adapter *adapter)
 		    hw->phy.media_type == e1000_media_type_internal_serdes) {
 			ew32(SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
 			e1e_flush();
-			usleep_range(10000, 20000);
+			usleep_range(10000, 11000);
 			break;
 		}
 		/* Fall Through */
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index cdae0efde8e6..395b05701480 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -271,7 +271,7 @@ static void e1000_toggle_lanphypc_pch_lpt(struct e1000_hw *hw)
 		u16 count = 20;
 
 		do {
-			usleep_range(5000, 10000);
+			usleep_range(5000, 6000);
 		} while (!(er32(CTRL_EXT) & E1000_CTRL_EXT_LPCD) && count--);
 
 		msleep(30);
@@ -405,7 +405,7 @@ static s32 e1000_init_phy_workarounds_pchlan(struct e1000_hw *hw)
 	/* Ungate automatic PHY configuration on non-managed 82579 */
 	if ((hw->mac.type == e1000_pch2lan) &&
 	    !(fwsm & E1000_ICH_FWSM_FW_VALID)) {
-		usleep_range(10000, 20000);
+		usleep_range(10000, 11000);
 		e1000_gate_hw_phy_config_ich8lan(hw, false);
 	}
 
@@ -531,7 +531,7 @@ static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw)
 	phy->id = 0;
 	while ((e1000_phy_unknown == e1000e_get_phy_type_from_id(phy->id)) &&
 	       (i++ < 100)) {
-		usleep_range(1000, 2000);
+		usleep_range(1000, 1100);
 		ret_val = e1000e_get_phy_id(hw);
 		if (ret_val)
 			return ret_val;
@@ -1244,7 +1244,7 @@ static s32 e1000_disable_ulp_lpt_lp(struct e1000_hw *hw, bool force)
 				goto out;
 			}
 
-			usleep_range(10000, 20000);
+			usleep_range(10000, 11000);
 		}
 		e_dbg("ULP_CONFIG_DONE cleared after %dmsec\n", i * 10);
 
@@ -1999,7 +1999,7 @@ static s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw)
 
 	while ((blocked = !(er32(FWSM) & E1000_ICH_FWSM_RSPCIPHY)) &&
 	       (i++ < 30))
-		usleep_range(10000, 20000);
+		usleep_range(10000, 11000);
 	return blocked ? E1000_BLK_PHY_RESET : 0;
 }
 
@@ -2818,7 +2818,7 @@ static s32 e1000_post_phy_reset_ich8lan(struct e1000_hw *hw)
 		return 0;
 
 	/* Allow time for h/w to get to quiescent state after reset */
-	usleep_range(10000, 20000);
+	usleep_range(10000, 11000);
 
 	/* Perform any necessary post-reset workarounds */
 	switch (hw->mac.type) {
@@ -2854,7 +2854,7 @@ static s32 e1000_post_phy_reset_ich8lan(struct e1000_hw *hw)
 	if (hw->mac.type == e1000_pch2lan) {
 		/* Ungate automatic PHY configuration on non-managed 82579 */
 		if (!(er32(FWSM) & E1000_ICH_FWSM_FW_VALID)) {
-			usleep_range(10000, 20000);
+			usleep_range(10000, 11000);
 			e1000_gate_hw_phy_config_ich8lan(hw, false);
 		}
 
@@ -3875,7 +3875,7 @@ static s32 e1000_update_nvm_checksum_spt(struct e1000_hw *hw)
 	 */
 	if (!ret_val) {
 		nvm->ops.reload(hw);
-		usleep_range(10000, 20000);
+		usleep_range(10000, 11000);
 	}
 
 out:
@@ -4026,7 +4026,7 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
 	 */
 	if (!ret_val) {
 		nvm->ops.reload(hw);
-		usleep_range(10000, 20000);
+		usleep_range(10000, 11000);
 	}
 
 out:
@@ -4650,7 +4650,7 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
 	ew32(TCTL, E1000_TCTL_PSP);
 	e1e_flush();
 
-	usleep_range(10000, 20000);
+	usleep_range(10000, 11000);
 
 	/* Workaround for ICH8 bit corruption issue in FIFO memory */
 	if (hw->mac.type == e1000_ich8lan) {
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 4abd55d646c5..e531976f8a67 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -797,7 +797,7 @@ static s32 e1000_poll_fiber_serdes_link_generic(struct e1000_hw *hw)
 	 * milliseconds even if the other end is doing it in SW).
 	 */
 	for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) {
-		usleep_range(10000, 20000);
+		usleep_range(10000, 11000);
 		status = er32(STATUS);
 		if (status & E1000_STATUS_LU)
 			break;
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 2454a3757bf3..f6f73d5347db 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -3208,7 +3208,7 @@ static void e1000_configure_rx(struct e1000_adapter *adapter)
 	if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX))
 		ew32(RCTL, rctl & ~E1000_RCTL_EN);
 	e1e_flush();
-	usleep_range(10000, 20000);
+	usleep_range(10000, 11000);
 
 	if (adapter->flags2 & FLAG2_DMA_BURST) {
 		/* set the writeback threshold (only takes effect if the RDTR
@@ -4272,7 +4272,7 @@ void e1000e_down(struct e1000_adapter *adapter, bool reset)
 
 	/* flush both disables and wait for them to finish */
 	e1e_flush();
-	usleep_range(10000, 20000);
+	usleep_range(10000, 11000);
 
 	e1000_irq_disable(adapter);
 
@@ -4310,7 +4310,7 @@ void e1000e_reinit_locked(struct e1000_adapter *adapter)
 {
 	might_sleep();
 	while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
-		usleep_range(1000, 2000);
+		usleep_range(1000, 1100);
 	e1000e_down(adapter, true);
 	e1000e_up(adapter);
 	clear_bit(__E1000_RESETTING, &adapter->state);
@@ -4707,7 +4707,7 @@ int e1000e_close(struct net_device *netdev)
 	int count = E1000_CHECK_RESET_COUNT;
 
 	while (test_bit(__E1000_RESETTING, &adapter->state) && count--)
-		usleep_range(10000, 20000);
+		usleep_range(10000, 11000);
 
 	WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
 
@@ -6021,7 +6021,7 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
 	}
 
 	while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
-		usleep_range(1000, 2000);
+		usleep_range(1000, 1100);
 	/* e1000e_down -> e1000e_reset dependent on max_frame_size & mtu */
 	adapter->max_frame_size = max_frame;
 	e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
@@ -6301,7 +6301,7 @@ static int e1000e_pm_freeze(struct device *dev)
 		int count = E1000_CHECK_RESET_COUNT;
 
 		while (test_bit(__E1000_RESETTING, &adapter->state) && count--)
-			usleep_range(10000, 20000);
+			usleep_range(10000, 11000);
 
 		WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
 
@@ -6716,7 +6716,7 @@ static int e1000e_pm_runtime_suspend(struct device *dev)
 		int count = E1000_CHECK_RESET_COUNT;
 
 		while (test_bit(__E1000_RESETTING, &adapter->state) && count--)
-			usleep_range(10000, 20000);
+			usleep_range(10000, 11000);
 
 		WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
 
diff --git a/drivers/net/ethernet/intel/e1000e/nvm.c b/drivers/net/ethernet/intel/e1000e/nvm.c
index 937f9af22d26..e609f4df86f4 100644
--- a/drivers/net/ethernet/intel/e1000e/nvm.c
+++ b/drivers/net/ethernet/intel/e1000e/nvm.c
@@ -392,7 +392,7 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 				break;
 			}
 		}
-		usleep_range(10000, 20000);
+		usleep_range(10000, 11000);
 		nvm->ops.release(hw);
 	}
 
-- 
2.21.0

[net-next 08/15] iavf: Fix up debug print macro

[Jeff Kirsher]

This aligns the iavf_debug() macro with the other Intel drivers.

Add the bus number, bus_id field to i40e_bus_info so output shows
each physical port(i.e func) in following format:
  [[[[<domain>]:]<bus>]:][<slot>][.[<func>]]
domains are numbered from 0 to ffff), bus (0-ff), slot (0-1f) and
function (0-7).

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
---
 drivers/net/ethernet/intel/iavf/iavf_osdep.h | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/intel/iavf/iavf_osdep.h b/drivers/net/ethernet/intel/iavf/iavf_osdep.h
index d39684558597..a452ce90679a 100644
--- a/drivers/net/ethernet/intel/iavf/iavf_osdep.h
+++ b/drivers/net/ethernet/intel/iavf/iavf_osdep.h
@@ -44,8 +44,12 @@ struct iavf_virt_mem {
 #define iavf_allocate_virt_mem(h, m, s) iavf_allocate_virt_mem_d(h, m, s)
 #define iavf_free_virt_mem(h, m) iavf_free_virt_mem_d(h, m)
 
-#define iavf_debug(h, m, s, ...)  iavf_debug_d(h, m, s, ##__VA_ARGS__)
-extern void iavf_debug_d(void *hw, u32 mask, char *fmt_str, ...)
-	__printf(3, 4);
+#define iavf_debug(h, m, s, ...)				\
+do {								\
+	if (((m) & (h)->debug_mask))				\
+		pr_info("iavf %02x:%02x.%x " s,			\
+			(h)->bus.bus_id, (h)->bus.device,	\
+			(h)->bus.func, ##__VA_ARGS__);		\
+} while (0)
 
 #endif /* _IAVF_OSDEP_H_ */
-- 
2.21.0

[net-next 09/15] igb: minor ethool regdump amendment

[Jeff Kirsher]

From: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

This patch has no functional impact and it is just a preparation
for the following patch. It removes an early return from the
'igb_get_regs()' function by moving the 82576-only registers
dump into an "if" block. With this preparation, we can dump more
non-82576 registers at the end of this function.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/igb/igb_ethtool.c | 70 ++++++++++----------
 1 file changed, 35 insertions(+), 35 deletions(-)

diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index c645d9e648e0..401bc2bd6b21 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -675,41 +675,41 @@ static void igb_get_regs(struct net_device *netdev,
 		regs_buff[554] = adapter->stats.b2ogprc;
 	}
 
-	if (hw->mac.type != e1000_82576)
-		return;
-	for (i = 0; i < 12; i++)
-		regs_buff[555 + i] = rd32(E1000_SRRCTL(i + 4));
-	for (i = 0; i < 4; i++)
-		regs_buff[567 + i] = rd32(E1000_PSRTYPE(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[571 + i] = rd32(E1000_RDBAL(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[583 + i] = rd32(E1000_RDBAH(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[595 + i] = rd32(E1000_RDLEN(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[607 + i] = rd32(E1000_RDH(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[619 + i] = rd32(E1000_RDT(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[631 + i] = rd32(E1000_RXDCTL(i + 4));
-
-	for (i = 0; i < 12; i++)
-		regs_buff[643 + i] = rd32(E1000_TDBAL(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[655 + i] = rd32(E1000_TDBAH(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[667 + i] = rd32(E1000_TDLEN(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[679 + i] = rd32(E1000_TDH(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[691 + i] = rd32(E1000_TDT(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[703 + i] = rd32(E1000_TXDCTL(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[715 + i] = rd32(E1000_TDWBAL(i + 4));
-	for (i = 0; i < 12; i++)
-		regs_buff[727 + i] = rd32(E1000_TDWBAH(i + 4));
+	if (hw->mac.type == e1000_82576) {
+		for (i = 0; i < 12; i++)
+			regs_buff[555 + i] = rd32(E1000_SRRCTL(i + 4));
+		for (i = 0; i < 4; i++)
+			regs_buff[567 + i] = rd32(E1000_PSRTYPE(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[571 + i] = rd32(E1000_RDBAL(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[583 + i] = rd32(E1000_RDBAH(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[595 + i] = rd32(E1000_RDLEN(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[607 + i] = rd32(E1000_RDH(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[619 + i] = rd32(E1000_RDT(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[631 + i] = rd32(E1000_RXDCTL(i + 4));
+
+		for (i = 0; i < 12; i++)
+			regs_buff[643 + i] = rd32(E1000_TDBAL(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[655 + i] = rd32(E1000_TDBAH(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[667 + i] = rd32(E1000_TDLEN(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[679 + i] = rd32(E1000_TDH(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[691 + i] = rd32(E1000_TDT(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[703 + i] = rd32(E1000_TXDCTL(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[715 + i] = rd32(E1000_TDWBAL(i + 4));
+		for (i = 0; i < 12; i++)
+			regs_buff[727 + i] = rd32(E1000_TDWBAH(i + 4));
+	}
 }
 
 static int igb_get_eeprom_len(struct net_device *netdev)
-- 
2.21.0

[net-next 10/15] igb: add RR2DCDELAY to ethtool registers dump

[Jeff Kirsher]

From: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

This patch adds the RR2DCDELAY register to the ethtool registers dump.
RR2DCDELAY exists on I210 and I211 Intel Gigabit Ethernet chips and it stands
for "Read Request To Data Completion Delay". Here is how this register is
described in the I210 datasheet:

"This field captures the maximum PCIe split time in 16 ns units, which is the
maximum delay between the read request to the first data completion. This is
giving an estimation of the PCIe round trip time."

In other words, whenever I210 reads from the host memory (e.g., fetches a
descriptor from the ring), the chip measures every PCI DMA read transaction and
captures the maximum value. So it ends up containing the longest DMA
transaction time.

This register is very useful for troubleshooting and research purposes. If you
are dealing with time-sensitive networks, this register can help you get
an idea of your "I210-to-ring" latency. This helps answering questions like
"should I have PCIe ASPM enabled?" or "should I enable deep C-states?" on
my system.

It is safe to read this register at any point, reading it has no effect on
the I210 chip functionality.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/igb/e1000_regs.h  | 2 ++
 drivers/net/ethernet/intel/igb/igb_ethtool.c | 5 ++++-
 2 files changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/igb/e1000_regs.h b/drivers/net/ethernet/intel/igb/e1000_regs.h
index 0ad737d2f289..9cb49980ec2d 100644
--- a/drivers/net/ethernet/intel/igb/e1000_regs.h
+++ b/drivers/net/ethernet/intel/igb/e1000_regs.h
@@ -409,6 +409,8 @@ do { \
 #define E1000_I210_TQAVCC(_n)	(0x3004 + ((_n) * 0x40))
 #define E1000_I210_TQAVHC(_n)	(0x300C + ((_n) * 0x40))
 
+#define E1000_I210_RR2DCDELAY	0x5BF4
+
 #define E1000_INVM_DATA_REG(_n)	(0x12120 + 4*(_n))
 #define E1000_INVM_SIZE		64 /* Number of INVM Data Registers */
 
diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index 401bc2bd6b21..3182b059bf55 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -448,7 +448,7 @@ static void igb_set_msglevel(struct net_device *netdev, u32 data)
 
 static int igb_get_regs_len(struct net_device *netdev)
 {
-#define IGB_REGS_LEN 739
+#define IGB_REGS_LEN 740
 	return IGB_REGS_LEN * sizeof(u32);
 }
 
@@ -710,6 +710,9 @@ static void igb_get_regs(struct net_device *netdev,
 		for (i = 0; i < 12; i++)
 			regs_buff[727 + i] = rd32(E1000_TDWBAH(i + 4));
 	}
+
+	if (hw->mac.type == e1000_i210 || hw->mac.type == e1000_i211)
+		regs_buff[739] = rd32(E1000_I210_RR2DCDELAY);
 }
 
 static int igb_get_eeprom_len(struct net_device *netdev)
-- 
2.21.0

[net-next 11/15] iavf: fix dereference of null rx_buffer pointer

[Jeff Kirsher]

From: Colin Ian King <colin.king@canonical.com>

A recent commit efa14c3985828d ("iavf: allow null RX descriptors") added
a null pointer sanity check on rx_buffer, however, rx_buffer is being
dereferenced before that check, which implies a null pointer dereference
bug can potentially occur.  Fix this by only dereferencing rx_buffer
until after the null pointer check.

Addresses-Coverity: ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/iavf/iavf_txrx.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/iavf/iavf_txrx.c b/drivers/net/ethernet/intel/iavf/iavf_txrx.c
index 1cde1601bc32..0cca1b589b56 100644
--- a/drivers/net/ethernet/intel/iavf/iavf_txrx.c
+++ b/drivers/net/ethernet/intel/iavf/iavf_txrx.c
@@ -1296,7 +1296,7 @@ static struct sk_buff *iavf_construct_skb(struct iavf_ring *rx_ring,
 					  struct iavf_rx_buffer *rx_buffer,
 					  unsigned int size)
 {
-	void *va = page_address(rx_buffer->page) + rx_buffer->page_offset;
+	void *va;
 #if (PAGE_SIZE < 8192)
 	unsigned int truesize = iavf_rx_pg_size(rx_ring) / 2;
 #else
@@ -1308,6 +1308,7 @@ static struct sk_buff *iavf_construct_skb(struct iavf_ring *rx_ring,
 	if (!rx_buffer)
 		return NULL;
 	/* prefetch first cache line of first page */
+	va = page_address(rx_buffer->page) + rx_buffer->page_offset;
 	prefetch(va);
 #if L1_CACHE_BYTES < 128
 	prefetch(va + L1_CACHE_BYTES);
@@ -1362,7 +1363,7 @@ static struct sk_buff *iavf_build_skb(struct iavf_ring *rx_ring,
 				      struct iavf_rx_buffer *rx_buffer,
 				      unsigned int size)
 {
-	void *va = page_address(rx_buffer->page) + rx_buffer->page_offset;
+	void *va;
 #if (PAGE_SIZE < 8192)
 	unsigned int truesize = iavf_rx_pg_size(rx_ring) / 2;
 #else
@@ -1374,6 +1375,7 @@ static struct sk_buff *iavf_build_skb(struct iavf_ring *rx_ring,
 	if (!rx_buffer)
 		return NULL;
 	/* prefetch first cache line of first page */
+	va = page_address(rx_buffer->page) + rx_buffer->page_offset;
 	prefetch(va);
 #if L1_CACHE_BYTES < 128
 	prefetch(va + L1_CACHE_BYTES);
-- 
2.21.0

[net-next 12/15] ixgbevf: Use cached link state instead of re-reading the value for ethtool

[Jeff Kirsher]

From: Alexander Duyck <alexander.h.duyck@linux.intel.com>

Change the ethtool link settings call to just read the cached state out of
the adapter structure instead of trying to recheck the value from the PF.
Doing this should prevent excessive reading of the mailbox.

Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Reviewed-by: "Guilherme G. Piccoli" <gpiccoli@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/ixgbevf/ethtool.c | 10 ++--------
 1 file changed, 2 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/intel/ixgbevf/ethtool.c b/drivers/net/ethernet/intel/ixgbevf/ethtool.c
index 5399787e07af..54459b69c948 100644
--- a/drivers/net/ethernet/intel/ixgbevf/ethtool.c
+++ b/drivers/net/ethernet/intel/ixgbevf/ethtool.c
@@ -85,22 +85,16 @@ static int ixgbevf_get_link_ksettings(struct net_device *netdev,
 				      struct ethtool_link_ksettings *cmd)
 {
 	struct ixgbevf_adapter *adapter = netdev_priv(netdev);
-	struct ixgbe_hw *hw = &adapter->hw;
-	u32 link_speed = 0;
-	bool link_up;
 
 	ethtool_link_ksettings_zero_link_mode(cmd, supported);
 	ethtool_link_ksettings_add_link_mode(cmd, supported, 10000baseT_Full);
 	cmd->base.autoneg = AUTONEG_DISABLE;
 	cmd->base.port = -1;
 
-	hw->mac.get_link_status = 1;
-	hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
-
-	if (link_up) {
+	if (adapter->link_up) {
 		__u32 speed = SPEED_10000;
 
-		switch (link_speed) {
+		switch (adapter->link_speed) {
 		case IXGBE_LINK_SPEED_10GB_FULL:
 			speed = SPEED_10000;
 			break;
-- 
2.21.0

[net-next 13/15] i40e: Add macvlan support on i40e

[Jeff Kirsher]

From: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>

This patch enables macvlan offloads for i40e. The idea is to use
channels as macvlan interfaces. The channels are VSIs of
type VMDQ. When the first macvlan is created, the maximum number of
channels possible are created. From then on, as a macvlan interface
is created, a macvlan filter is added to these already created
channels (VSIs).

This patch utilizes subordinate device traffic classes to make queue
groups(channels) available for an upper device like a macvlan.

Steps to configure macvlan offloads:
1. ethtool -K ethx l2-fwd-offload on
2. ip link add link ethx name macvlan1 type macvlan
3. ip addr add <address> dev macvlan1
4. ip link set macvlan1 up

Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/i40e/i40e.h      |  27 ++
 drivers/net/ethernet/intel/i40e/i40e_main.c | 497 +++++++++++++++++++-
 2 files changed, 522 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e.h b/drivers/net/ethernet/intel/i40e/i40e.h
index 24e6ce6517a7..84bd06901014 100644
--- a/drivers/net/ethernet/intel/i40e/i40e.h
+++ b/drivers/net/ethernet/intel/i40e/i40e.h
@@ -27,6 +27,7 @@
 #include <net/ip6_checksum.h>
 #include <linux/ethtool.h>
 #include <linux/if_vlan.h>
+#include <linux/if_macvlan.h>
 #include <linux/if_bridge.h>
 #include <linux/clocksource.h>
 #include <linux/net_tstamp.h>
@@ -412,6 +413,11 @@ struct i40e_flex_pit {
 	u8 pit_index;
 };
 
+struct i40e_fwd_adapter {
+	struct net_device *netdev;
+	int bit_no;
+};
+
 struct i40e_channel {
 	struct list_head list;
 	bool initialized;
@@ -426,11 +432,25 @@ struct i40e_channel {
 	struct i40e_aqc_vsi_properties_data info;
 
 	u64 max_tx_rate;
+	struct i40e_fwd_adapter *fwd;
 
 	/* track this channel belongs to which VSI */
 	struct i40e_vsi *parent_vsi;
 };
 
+static inline bool i40e_is_channel_macvlan(struct i40e_channel *ch)
+{
+	return !!ch->fwd;
+}
+
+static inline u8 *i40e_channel_mac(struct i40e_channel *ch)
+{
+	if (i40e_is_channel_macvlan(ch))
+		return ch->fwd->netdev->dev_addr;
+	else
+		return NULL;
+}
+
 /* struct that defines the Ethernet device */
 struct i40e_pf {
 	struct pci_dev *pdev;
@@ -813,6 +833,13 @@ struct i40e_vsi {
 	struct list_head ch_list;
 	u16 tc_seid_map[I40E_MAX_TRAFFIC_CLASS];
 
+	/* macvlan fields */
+#define I40E_MAX_MACVLANS		128 /* Max HW vectors - 1 on FVL */
+#define I40E_MIN_MACVLAN_VECTORS	2   /* Min vectors to enable macvlans */
+	DECLARE_BITMAP(fwd_bitmask, I40E_MAX_MACVLANS);
+	struct list_head macvlan_list;
+	int macvlan_cnt;
+
 	void *priv;	/* client driver data reference. */
 
 	/* VSI specific handlers */
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index 8b0c29b7809b..5361c08328f7 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -5861,8 +5861,10 @@ static int i40e_add_channel(struct i40e_pf *pf, u16 uplink_seid,
 		return -ENOENT;
 	}
 
-	/* Success, update channel */
-	ch->enabled_tc = enabled_tc;
+	/* Success, update channel, set enabled_tc only if the channel
+	 * is not a macvlan
+	 */
+	ch->enabled_tc = !i40e_is_channel_macvlan(ch) && enabled_tc;
 	ch->seid = ctxt.seid;
 	ch->vsi_number = ctxt.vsi_number;
 	ch->stat_counter_idx = cpu_to_le16(ctxt.info.stat_counter_idx);
@@ -6911,6 +6913,489 @@ static void i40e_vsi_set_default_tc_config(struct i40e_vsi *vsi)
 	}
 }
 
+/**
+ * i40e_del_macvlan_filter
+ * @hw: pointer to the HW structure
+ * @seid: seid of the channel VSI
+ * @macaddr: the mac address to apply as a filter
+ * @aq_err: store the admin Q error
+ *
+ * This function deletes a mac filter on the channel VSI which serves as the
+ * macvlan. Returns 0 on success.
+ **/
+static i40e_status i40e_del_macvlan_filter(struct i40e_hw *hw, u16 seid,
+					   const u8 *macaddr, int *aq_err)
+{
+	struct i40e_aqc_remove_macvlan_element_data element;
+	i40e_status status;
+
+	memset(&element, 0, sizeof(element));
+	ether_addr_copy(element.mac_addr, macaddr);
+	element.vlan_tag = 0;
+	element.flags = I40E_AQC_MACVLAN_DEL_PERFECT_MATCH;
+	status = i40e_aq_remove_macvlan(hw, seid, &element, 1, NULL);
+	*aq_err = hw->aq.asq_last_status;
+
+	return status;
+}
+
+/**
+ * i40e_add_macvlan_filter
+ * @hw: pointer to the HW structure
+ * @seid: seid of the channel VSI
+ * @macaddr: the mac address to apply as a filter
+ * @aq_err: store the admin Q error
+ *
+ * This function adds a mac filter on the channel VSI which serves as the
+ * macvlan. Returns 0 on success.
+ **/
+static i40e_status i40e_add_macvlan_filter(struct i40e_hw *hw, u16 seid,
+					   const u8 *macaddr, int *aq_err)
+{
+	struct i40e_aqc_add_macvlan_element_data element;
+	i40e_status status;
+	u16 cmd_flags = 0;
+
+	ether_addr_copy(element.mac_addr, macaddr);
+	element.vlan_tag = 0;
+	element.queue_number = 0;
+	element.match_method = I40E_AQC_MM_ERR_NO_RES;
+	cmd_flags |= I40E_AQC_MACVLAN_ADD_PERFECT_MATCH;
+	element.flags = cpu_to_le16(cmd_flags);
+	status = i40e_aq_add_macvlan(hw, seid, &element, 1, NULL);
+	*aq_err = hw->aq.asq_last_status;
+
+	return status;
+}
+
+/**
+ * i40e_reset_ch_rings - Reset the queue contexts in a channel
+ * @vsi: the VSI we want to access
+ * @ch: the channel we want to access
+ */
+static void i40e_reset_ch_rings(struct i40e_vsi *vsi, struct i40e_channel *ch)
+{
+	struct i40e_ring *tx_ring, *rx_ring;
+	u16 pf_q;
+	int i;
+
+	for (i = 0; i < ch->num_queue_pairs; i++) {
+		pf_q = ch->base_queue + i;
+		tx_ring = vsi->tx_rings[pf_q];
+		tx_ring->ch = NULL;
+		rx_ring = vsi->rx_rings[pf_q];
+		rx_ring->ch = NULL;
+	}
+}
+
+/**
+ * i40e_free_macvlan_channels
+ * @vsi: the VSI we want to access
+ *
+ * This function frees the Qs of the channel VSI from
+ * the stack and also deletes the channel VSIs which
+ * serve as macvlans.
+ */
+static void i40e_free_macvlan_channels(struct i40e_vsi *vsi)
+{
+	struct i40e_channel *ch, *ch_tmp;
+	int ret;
+
+	if (list_empty(&vsi->macvlan_list))
+		return;
+
+	list_for_each_entry_safe(ch, ch_tmp, &vsi->macvlan_list, list) {
+		struct i40e_vsi *parent_vsi;
+
+		if (i40e_is_channel_macvlan(ch)) {
+			i40e_reset_ch_rings(vsi, ch);
+			clear_bit(ch->fwd->bit_no, vsi->fwd_bitmask);
+			netdev_unbind_sb_channel(vsi->netdev, ch->fwd->netdev);
+			netdev_set_sb_channel(ch->fwd->netdev, 0);
+			kfree(ch->fwd);
+			ch->fwd = NULL;
+		}
+
+		list_del(&ch->list);
+		parent_vsi = ch->parent_vsi;
+		if (!parent_vsi || !ch->initialized) {
+			kfree(ch);
+			continue;
+		}
+
+		/* remove the VSI */
+		ret = i40e_aq_delete_element(&vsi->back->hw, ch->seid,
+					     NULL);
+		if (ret)
+			dev_err(&vsi->back->pdev->dev,
+				"unable to remove channel (%d) for parent VSI(%d)\n",
+				ch->seid, parent_vsi->seid);
+		kfree(ch);
+	}
+	vsi->macvlan_cnt = 0;
+}
+
+/**
+ * i40e_fwd_ring_up - bring the macvlan device up
+ * @vsi: the VSI we want to access
+ * @vdev: macvlan netdevice
+ * @fwd: the private fwd structure
+ */
+static int i40e_fwd_ring_up(struct i40e_vsi *vsi, struct net_device *vdev,
+			    struct i40e_fwd_adapter *fwd)
+{
+	int ret = 0, num_tc = 1,  i, aq_err;
+	struct i40e_channel *ch, *ch_tmp;
+	struct i40e_pf *pf = vsi->back;
+	struct i40e_hw *hw = &pf->hw;
+
+	if (list_empty(&vsi->macvlan_list))
+		return -EINVAL;
+
+	/* Go through the list and find an available channel */
+	list_for_each_entry_safe(ch, ch_tmp, &vsi->macvlan_list, list) {
+		if (!i40e_is_channel_macvlan(ch)) {
+			ch->fwd = fwd;
+			/* record configuration for macvlan interface in vdev */
+			for (i = 0; i < num_tc; i++)
+				netdev_bind_sb_channel_queue(vsi->netdev, vdev,
+							     i,
+							     ch->num_queue_pairs,
+							     ch->base_queue);
+			for (i = 0; i < ch->num_queue_pairs; i++) {
+				struct i40e_ring *tx_ring, *rx_ring;
+				u16 pf_q;
+
+				pf_q = ch->base_queue + i;
+
+				/* Get to TX ring ptr */
+				tx_ring = vsi->tx_rings[pf_q];
+				tx_ring->ch = ch;
+
+				/* Get the RX ring ptr */
+				rx_ring = vsi->rx_rings[pf_q];
+				rx_ring->ch = ch;
+			}
+			break;
+		}
+	}
+
+	/* Guarantee all rings are updated before we update the
+	 * MAC address filter.
+	 */
+	wmb();
+
+	/* Add a mac filter */
+	ret = i40e_add_macvlan_filter(hw, ch->seid, vdev->dev_addr, &aq_err);
+	if (ret) {
+		/* if we cannot add the MAC rule then disable the offload */
+		macvlan_release_l2fw_offload(vdev);
+		for (i = 0; i < ch->num_queue_pairs; i++) {
+			struct i40e_ring *rx_ring;
+			u16 pf_q;
+
+			pf_q = ch->base_queue + i;
+			rx_ring = vsi->rx_rings[pf_q];
+			rx_ring->netdev = NULL;
+		}
+		dev_info(&pf->pdev->dev,
+			 "Error adding mac filter on macvlan err %s, aq_err %s\n",
+			  i40e_stat_str(hw, ret),
+			  i40e_aq_str(hw, aq_err));
+		netdev_err(vdev, "L2fwd offload disabled to L2 filter error\n");
+	}
+
+	return ret;
+}
+
+/**
+ * i40e_setup_macvlans - create the channels which will be macvlans
+ * @vsi: the VSI we want to access
+ * @macvlan_cnt: no. of macvlans to be setup
+ * @qcnt: no. of Qs per macvlan
+ * @vdev: macvlan netdevice
+ */
+static int i40e_setup_macvlans(struct i40e_vsi *vsi, u16 macvlan_cnt, u16 qcnt,
+			       struct net_device *vdev)
+{
+	struct i40e_pf *pf = vsi->back;
+	struct i40e_hw *hw = &pf->hw;
+	struct i40e_vsi_context ctxt;
+	u16 sections, qmap, num_qps;
+	struct i40e_channel *ch;
+	int i, pow, ret = 0;
+	u8 offset = 0;
+
+	if (vsi->type != I40E_VSI_MAIN || !macvlan_cnt)
+		return -EINVAL;
+
+	num_qps = vsi->num_queue_pairs - (macvlan_cnt * qcnt);
+
+	/* find the next higher power-of-2 of num queue pairs */
+	pow = fls(roundup_pow_of_two(num_qps) - 1);
+
+	qmap = (offset << I40E_AQ_VSI_TC_QUE_OFFSET_SHIFT) |
+		(pow << I40E_AQ_VSI_TC_QUE_NUMBER_SHIFT);
+
+	/* Setup context bits for the main VSI */
+	sections = I40E_AQ_VSI_PROP_QUEUE_MAP_VALID;
+	sections |= I40E_AQ_VSI_PROP_SCHED_VALID;
+	memset(&ctxt, 0, sizeof(ctxt));
+	ctxt.seid = vsi->seid;
+	ctxt.pf_num = vsi->back->hw.pf_id;
+	ctxt.vf_num = 0;
+	ctxt.uplink_seid = vsi->uplink_seid;
+	ctxt.info = vsi->info;
+	ctxt.info.tc_mapping[0] = cpu_to_le16(qmap);
+	ctxt.info.mapping_flags |= cpu_to_le16(I40E_AQ_VSI_QUE_MAP_CONTIG);
+	ctxt.info.queue_mapping[0] = cpu_to_le16(vsi->base_queue);
+	ctxt.info.valid_sections |= cpu_to_le16(sections);
+
+	/* Reconfigure RSS for main VSI with new max queue count */
+	vsi->rss_size = max_t(u16, num_qps, qcnt);
+	ret = i40e_vsi_config_rss(vsi);
+	if (ret) {
+		dev_info(&pf->pdev->dev,
+			 "Failed to reconfig RSS for num_queues (%u)\n",
+			 vsi->rss_size);
+		return ret;
+	}
+	vsi->reconfig_rss = true;
+	dev_dbg(&vsi->back->pdev->dev,
+		"Reconfigured RSS with num_queues (%u)\n", vsi->rss_size);
+	vsi->next_base_queue = num_qps;
+	vsi->cnt_q_avail = vsi->num_queue_pairs - num_qps;
+
+	/* Update the VSI after updating the VSI queue-mapping
+	 * information
+	 */
+	ret = i40e_aq_update_vsi_params(hw, &ctxt, NULL);
+	if (ret) {
+		dev_info(&pf->pdev->dev,
+			 "Update vsi tc config failed, err %s aq_err %s\n",
+			 i40e_stat_str(hw, ret),
+			 i40e_aq_str(hw, hw->aq.asq_last_status));
+		return ret;
+	}
+	/* update the local VSI info with updated queue map */
+	i40e_vsi_update_queue_map(vsi, &ctxt);
+	vsi->info.valid_sections = 0;
+
+	/* Create channels for macvlans */
+	INIT_LIST_HEAD(&vsi->macvlan_list);
+	for (i = 0; i < macvlan_cnt; i++) {
+		ch = kzalloc(sizeof(*ch), GFP_KERNEL);
+		if (!ch) {
+			ret = -ENOMEM;
+			goto err_free;
+		}
+		INIT_LIST_HEAD(&ch->list);
+		ch->num_queue_pairs = qcnt;
+		if (!i40e_setup_channel(pf, vsi, ch)) {
+			ret = -EINVAL;
+			goto err_free;
+		}
+		ch->parent_vsi = vsi;
+		vsi->cnt_q_avail -= ch->num_queue_pairs;
+		vsi->macvlan_cnt++;
+		list_add_tail(&ch->list, &vsi->macvlan_list);
+	}
+
+	return ret;
+
+err_free:
+	dev_info(&pf->pdev->dev, "Failed to setup macvlans\n");
+	i40e_free_macvlan_channels(vsi);
+
+	return ret;
+}
+
+/**
+ * i40e_fwd_add - configure macvlans
+ * @netdev: net device to configure
+ * @vdev: macvlan netdevice
+ **/
+static void *i40e_fwd_add(struct net_device *netdev, struct net_device *vdev)
+{
+	struct i40e_netdev_priv *np = netdev_priv(netdev);
+	u16 q_per_macvlan = 0, macvlan_cnt = 0, vectors;
+	struct i40e_vsi *vsi = np->vsi;
+	struct i40e_pf *pf = vsi->back;
+	struct i40e_fwd_adapter *fwd;
+	int avail_macvlan, ret;
+
+	if ((pf->flags & I40E_FLAG_DCB_ENABLED)) {
+		netdev_info(netdev, "Macvlans are not supported when DCB is enabled\n");
+		return ERR_PTR(-EINVAL);
+	}
+	if ((pf->flags & I40E_FLAG_TC_MQPRIO)) {
+		netdev_info(netdev, "Macvlans are not supported when HW TC offload is on\n");
+		return ERR_PTR(-EINVAL);
+	}
+	if (pf->num_lan_msix < I40E_MIN_MACVLAN_VECTORS) {
+		netdev_info(netdev, "Not enough vectors available to support macvlans\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	/* The macvlan device has to be a single Q device so that the
+	 * tc_to_txq field can be reused to pick the tx queue.
+	 */
+	if (netif_is_multiqueue(vdev))
+		return ERR_PTR(-ERANGE);
+
+	if (!vsi->macvlan_cnt) {
+		/* reserve bit 0 for the pf device */
+		set_bit(0, vsi->fwd_bitmask);
+
+		/* Try to reserve as many queues as possible for macvlans. First
+		 * reserve 3/4th of max vectors, then half, then quarter and
+		 * calculate Qs per macvlan as you go
+		 */
+		vectors = pf->num_lan_msix;
+		if (vectors <= I40E_MAX_MACVLANS && vectors > 64) {
+			/* allocate 4 Qs per macvlan and 32 Qs to the PF*/
+			q_per_macvlan = 4;
+			macvlan_cnt = (vectors - 32) / 4;
+		} else if (vectors <= 64 && vectors > 32) {
+			/* allocate 2 Qs per macvlan and 16 Qs to the PF*/
+			q_per_macvlan = 2;
+			macvlan_cnt = (vectors - 16) / 2;
+		} else if (vectors <= 32 && vectors > 16) {
+			/* allocate 1 Q per macvlan and 16 Qs to the PF*/
+			q_per_macvlan = 1;
+			macvlan_cnt = vectors - 16;
+		} else if (vectors <= 16 && vectors > 8) {
+			/* allocate 1 Q per macvlan and 8 Qs to the PF */
+			q_per_macvlan = 1;
+			macvlan_cnt = vectors - 8;
+		} else {
+			/* allocate 1 Q per macvlan and 1 Q to the PF */
+			q_per_macvlan = 1;
+			macvlan_cnt = vectors - 1;
+		}
+
+		if (macvlan_cnt == 0)
+			return ERR_PTR(-EBUSY);
+
+		/* Quiesce VSI queues */
+		i40e_quiesce_vsi(vsi);
+
+		/* sets up the macvlans but does not "enable" them */
+		ret = i40e_setup_macvlans(vsi, macvlan_cnt, q_per_macvlan,
+					  vdev);
+		if (ret)
+			return ERR_PTR(ret);
+
+		/* Unquiesce VSI */
+		i40e_unquiesce_vsi(vsi);
+	}
+	avail_macvlan = find_first_zero_bit(vsi->fwd_bitmask,
+					    vsi->macvlan_cnt);
+	if (avail_macvlan >= I40E_MAX_MACVLANS)
+		return ERR_PTR(-EBUSY);
+
+	/* create the fwd struct */
+	fwd = kzalloc(sizeof(*fwd), GFP_KERNEL);
+	if (!fwd)
+		return ERR_PTR(-ENOMEM);
+
+	set_bit(avail_macvlan, vsi->fwd_bitmask);
+	fwd->bit_no = avail_macvlan;
+	netdev_set_sb_channel(vdev, avail_macvlan);
+	fwd->netdev = vdev;
+
+	if (!netif_running(netdev))
+		return fwd;
+
+	/* Set fwd ring up */
+	ret = i40e_fwd_ring_up(vsi, vdev, fwd);
+	if (ret) {
+		/* unbind the queues and drop the subordinate channel config */
+		netdev_unbind_sb_channel(netdev, vdev);
+		netdev_set_sb_channel(vdev, 0);
+
+		kfree(fwd);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return fwd;
+}
+
+/**
+ * i40e_del_all_macvlans - Delete all the mac filters on the channels
+ * @vsi: the VSI we want to access
+ */
+static void i40e_del_all_macvlans(struct i40e_vsi *vsi)
+{
+	struct i40e_channel *ch, *ch_tmp;
+	struct i40e_pf *pf = vsi->back;
+	struct i40e_hw *hw = &pf->hw;
+	int aq_err, ret = 0;
+
+	if (list_empty(&vsi->macvlan_list))
+		return;
+
+	list_for_each_entry_safe(ch, ch_tmp, &vsi->macvlan_list, list) {
+		if (i40e_is_channel_macvlan(ch)) {
+			ret = i40e_del_macvlan_filter(hw, ch->seid,
+						      i40e_channel_mac(ch),
+						      &aq_err);
+			if (!ret) {
+				/* Reset queue contexts */
+				i40e_reset_ch_rings(vsi, ch);
+				clear_bit(ch->fwd->bit_no, vsi->fwd_bitmask);
+				netdev_unbind_sb_channel(vsi->netdev,
+							 ch->fwd->netdev);
+				netdev_set_sb_channel(ch->fwd->netdev, 0);
+				kfree(ch->fwd);
+				ch->fwd = NULL;
+			}
+		}
+	}
+}
+
+/**
+ * i40e_fwd_del - delete macvlan interfaces
+ * @netdev: net device to configure
+ * @vdev: macvlan netdevice
+ */
+static void i40e_fwd_del(struct net_device *netdev, void *vdev)
+{
+	struct i40e_netdev_priv *np = netdev_priv(netdev);
+	struct i40e_fwd_adapter *fwd = vdev;
+	struct i40e_channel *ch, *ch_tmp;
+	struct i40e_vsi *vsi = np->vsi;
+	struct i40e_pf *pf = vsi->back;
+	struct i40e_hw *hw = &pf->hw;
+	int aq_err, ret = 0;
+
+	/* Find the channel associated with the macvlan and del mac filter */
+	list_for_each_entry_safe(ch, ch_tmp, &vsi->macvlan_list, list) {
+		if (i40e_is_channel_macvlan(ch) &&
+		    ether_addr_equal(i40e_channel_mac(ch),
+				     fwd->netdev->dev_addr)) {
+			ret = i40e_del_macvlan_filter(hw, ch->seid,
+						      i40e_channel_mac(ch),
+						      &aq_err);
+			if (!ret) {
+				/* Reset queue contexts */
+				i40e_reset_ch_rings(vsi, ch);
+				clear_bit(ch->fwd->bit_no, vsi->fwd_bitmask);
+				netdev_unbind_sb_channel(netdev, fwd->netdev);
+				netdev_set_sb_channel(fwd->netdev, 0);
+				kfree(ch->fwd);
+				ch->fwd = NULL;
+			} else {
+				dev_info(&pf->pdev->dev,
+					 "Error deleting mac filter on macvlan err %s, aq_err %s\n",
+					  i40e_stat_str(hw, ret),
+					  i40e_aq_str(hw, aq_err));
+			}
+			break;
+		}
+	}
+}
+
 /**
  * i40e_setup_tc - configure multiple traffic classes
  * @netdev: net device to configure
@@ -11665,6 +12150,9 @@ static int i40e_set_features(struct net_device *netdev,
 		return -EINVAL;
 	}
 
+	if (!(features & NETIF_F_HW_L2FW_DOFFLOAD) && vsi->macvlan_cnt)
+		i40e_del_all_macvlans(vsi);
+
 	need_reset = i40e_set_ntuple(pf, features);
 
 	if (need_reset)
@@ -12409,6 +12897,8 @@ static const struct net_device_ops i40e_netdev_ops = {
 	.ndo_bpf		= i40e_xdp,
 	.ndo_xdp_xmit		= i40e_xdp_xmit,
 	.ndo_xsk_async_xmit	= i40e_xsk_async_xmit,
+	.ndo_dfwd_add_station	= i40e_fwd_add,
+	.ndo_dfwd_del_station	= i40e_fwd_del,
 };
 
 /**
@@ -12468,6 +12958,9 @@ static int i40e_config_netdev(struct i40e_vsi *vsi)
 	/* record features VLANs can make use of */
 	netdev->vlan_features |= hw_enc_features | NETIF_F_TSO_MANGLEID;
 
+	/* enable macvlan offloads */
+	netdev->hw_features |= NETIF_F_HW_L2FW_DOFFLOAD;
+
 	hw_features = hw_enc_features		|
 		      NETIF_F_HW_VLAN_CTAG_TX	|
 		      NETIF_F_HW_VLAN_CTAG_RX;
-- 
2.21.0

[net-next 14/15] e1000e: Make watchdog use delayed work

[Jeff Kirsher]

From: Detlev Casanova <detlev.casanova@gmail.com>

Use delayed work instead of timers to run the watchdog of the e1000e
driver.

Simplify the code with one less middle function.

Signed-off-by: Detlev Casanova <detlev.casanova@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/e1000.h  |  5 +-
 drivers/net/ethernet/intel/e1000e/netdev.c | 54 ++++++++++++----------
 2 files changed, 32 insertions(+), 27 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index be13227f1697..34cd67951aec 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -186,12 +186,13 @@ struct e1000_phy_regs {
 
 /* board specific private data structure */
 struct e1000_adapter {
-	struct timer_list watchdog_timer;
 	struct timer_list phy_info_timer;
 	struct timer_list blink_timer;
 
 	struct work_struct reset_task;
-	struct work_struct watchdog_task;
+	struct delayed_work watchdog_task;
+
+	struct workqueue_struct *e1000_workqueue;
 
 	const struct e1000_info *ei;
 
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index f6f73d5347db..b5fed6177ad6 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1780,7 +1780,8 @@ static irqreturn_t e1000_intr_msi(int __always_unused irq, void *data)
 		}
 		/* guard against interrupt when we're going down */
 		if (!test_bit(__E1000_DOWN, &adapter->state))
-			mod_timer(&adapter->watchdog_timer, jiffies + 1);
+			queue_delayed_work(adapter->e1000_workqueue,
+					   &adapter->watchdog_task, 1);
 	}
 
 	/* Reset on uncorrectable ECC error */
@@ -1860,7 +1861,8 @@ static irqreturn_t e1000_intr(int __always_unused irq, void *data)
 		}
 		/* guard against interrupt when we're going down */
 		if (!test_bit(__E1000_DOWN, &adapter->state))
-			mod_timer(&adapter->watchdog_timer, jiffies + 1);
+			queue_delayed_work(adapter->e1000_workqueue,
+					   &adapter->watchdog_task, 1);
 	}
 
 	/* Reset on uncorrectable ECC error */
@@ -1905,7 +1907,8 @@ static irqreturn_t e1000_msix_other(int __always_unused irq, void *data)
 		hw->mac.get_link_status = true;
 		/* guard against interrupt when we're going down */
 		if (!test_bit(__E1000_DOWN, &adapter->state))
-			mod_timer(&adapter->watchdog_timer, jiffies + 1);
+			queue_delayed_work(adapter->e1000_workqueue,
+					   &adapter->watchdog_task, 1);
 	}
 
 	if (!test_bit(__E1000_DOWN, &adapter->state))
@@ -4278,7 +4281,6 @@ void e1000e_down(struct e1000_adapter *adapter, bool reset)
 
 	napi_synchronize(&adapter->napi);
 
-	del_timer_sync(&adapter->watchdog_timer);
 	del_timer_sync(&adapter->phy_info_timer);
 
 	spin_lock(&adapter->stats64_lock);
@@ -5150,25 +5152,11 @@ static void e1000e_check_82574_phy_workaround(struct e1000_adapter *adapter)
 	}
 }
 
-/**
- * e1000_watchdog - Timer Call-back
- * @data: pointer to adapter cast into an unsigned long
- **/
-static void e1000_watchdog(struct timer_list *t)
-{
-	struct e1000_adapter *adapter = from_timer(adapter, t, watchdog_timer);
-
-	/* Do the rest outside of interrupt context */
-	schedule_work(&adapter->watchdog_task);
-
-	/* TODO: make this use queue_delayed_work() */
-}
-
 static void e1000_watchdog_task(struct work_struct *work)
 {
 	struct e1000_adapter *adapter = container_of(work,
 						     struct e1000_adapter,
-						     watchdog_task);
+						     watchdog_task.work);
 	struct net_device *netdev = adapter->netdev;
 	struct e1000_mac_info *mac = &adapter->hw.mac;
 	struct e1000_phy_info *phy = &adapter->hw.phy;
@@ -5400,8 +5388,9 @@ static void e1000_watchdog_task(struct work_struct *work)
 
 	/* Reset the timer */
 	if (!test_bit(__E1000_DOWN, &adapter->state))
-		mod_timer(&adapter->watchdog_timer,
-			  round_jiffies(jiffies + 2 * HZ));
+		queue_delayed_work(adapter->e1000_workqueue,
+				   &adapter->watchdog_task,
+				   round_jiffies(2 * HZ));
 }
 
 #define E1000_TX_FLAGS_CSUM		0x00000001
@@ -7256,11 +7245,21 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 		goto err_eeprom;
 	}
 
-	timer_setup(&adapter->watchdog_timer, e1000_watchdog, 0);
+	adapter->e1000_workqueue = alloc_workqueue("%s", WQ_MEM_RECLAIM, 0,
+						   e1000e_driver_name);
+
+	if (!adapter->e1000_workqueue) {
+		err = -ENOMEM;
+		goto err_workqueue;
+	}
+
+	INIT_DELAYED_WORK(&adapter->watchdog_task, e1000_watchdog_task);
+	queue_delayed_work(adapter->e1000_workqueue, &adapter->watchdog_task,
+			   0);
+
 	timer_setup(&adapter->phy_info_timer, e1000_update_phy_info, 0);
 
 	INIT_WORK(&adapter->reset_task, e1000_reset_task);
-	INIT_WORK(&adapter->watchdog_task, e1000_watchdog_task);
 	INIT_WORK(&adapter->downshift_task, e1000e_downshift_workaround);
 	INIT_WORK(&adapter->update_phy_task, e1000e_update_phy_task);
 	INIT_WORK(&adapter->print_hang_task, e1000_print_hw_hang);
@@ -7354,6 +7353,9 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	return 0;
 
 err_register:
+	flush_workqueue(adapter->e1000_workqueue);
+	destroy_workqueue(adapter->e1000_workqueue);
+err_workqueue:
 	if (!(adapter->flags & FLAG_HAS_AMT))
 		e1000e_release_hw_control(adapter);
 err_eeprom:
@@ -7400,15 +7402,17 @@ static void e1000_remove(struct pci_dev *pdev)
 	 */
 	if (!down)
 		set_bit(__E1000_DOWN, &adapter->state);
-	del_timer_sync(&adapter->watchdog_timer);
 	del_timer_sync(&adapter->phy_info_timer);
 
 	cancel_work_sync(&adapter->reset_task);
-	cancel_work_sync(&adapter->watchdog_task);
 	cancel_work_sync(&adapter->downshift_task);
 	cancel_work_sync(&adapter->update_phy_task);
 	cancel_work_sync(&adapter->print_hang_task);
 
+	cancel_delayed_work(&adapter->watchdog_task);
+	flush_workqueue(adapter->e1000_workqueue);
+	destroy_workqueue(adapter->e1000_workqueue);
+
 	if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) {
 		cancel_work_sync(&adapter->tx_hwtstamp_work);
 		if (adapter->tx_hwtstamp_skb) {
-- 
2.21.0

[net-next 15/15] e1000e: PCIm function state support

[Jeff Kirsher]

From: Vitaly Lifshits <vitaly.lifshits@intel.com>

Due to commit: 5d8682588605 ("[misc] mei: me: allow runtime
pm for platform with D0i3")
When disconnecting the cable and reconnecting it the NIC
enters DMoff state. This caused wrong link indication
and duplex mismatch. This bug is described in:
https://bugzilla.redhat.com/show_bug.cgi?id=1689436

Checking PCIm function state and performing PHY reset after a
timeout in watchdog task solves this issue.

Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  3 +++
 drivers/net/ethernet/intel/e1000e/netdev.c  | 18 +++++++++++++++++-
 2 files changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index fd550dee4982..63c3c79380a1 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -222,6 +222,9 @@
 #define E1000_STATUS_PHYRA      0x00000400      /* PHY Reset Asserted */
 #define E1000_STATUS_GIO_MASTER_ENABLE	0x00080000	/* Master Req status */
 
+/* PCIm function state */
+#define E1000_STATUS_PCIM_STATE	0x40000000
+
 #define HALF_DUPLEX 1
 #define FULL_DUPLEX 2
 
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index b5fed6177ad6..e4baa13b3cda 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -5161,8 +5161,9 @@ static void e1000_watchdog_task(struct work_struct *work)
 	struct e1000_mac_info *mac = &adapter->hw.mac;
 	struct e1000_phy_info *phy = &adapter->hw.phy;
 	struct e1000_ring *tx_ring = adapter->tx_ring;
+	u32 dmoff_exit_timeout = 100, tries = 0;
 	struct e1000_hw *hw = &adapter->hw;
-	u32 link, tctl;
+	u32 link, tctl, pcim_state;
 
 	if (test_bit(__E1000_DOWN, &adapter->state))
 		return;
@@ -5187,6 +5188,21 @@ static void e1000_watchdog_task(struct work_struct *work)
 			/* Cancel scheduled suspend requests. */
 			pm_runtime_resume(netdev->dev.parent);
 
+			/* Checking if MAC is in DMoff state*/
+			pcim_state = er32(STATUS);
+			while (pcim_state & E1000_STATUS_PCIM_STATE) {
+				if (tries++ == dmoff_exit_timeout) {
+					e_dbg("Error in exiting dmoff\n");
+					break;
+				}
+				usleep_range(10000, 20000);
+				pcim_state = er32(STATUS);
+
+				/* Checking if MAC exited DMoff state */
+				if (!(pcim_state & E1000_STATUS_PCIM_STATE))
+					e1000_phy_hw_reset(&adapter->hw);
+			}
+
 			/* update snapshot of PHY registers on LSC */
 			e1000_phy_read_status(adapter);
 			mac->ops.get_link_up_info(&adapter->hw,
-- 
2.21.0

Re: [net-next 03/15] ixgbe: Avoid NULL pointer dereference with VF on non-IPsec hw

[Shannon Nelson]

On 6/28/19 3:49 PM, Jeff Kirsher wrote:
> From: Dann Frazier <dann.frazier@canonical.com>
>
> An ipsec structure will not be allocated if the hardware does not support
> offload. Fixes the following Oops:
>
> [  191.045452] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
> [  191.054232] Mem abort info:
> [  191.057014]   ESR = 0x96000004
> [  191.060057]   Exception class = DABT (current EL), IL = 32 bits
> [  191.065963]   SET = 0, FnV = 0
> [  191.069004]   EA = 0, S1PTW = 0
> [  191.072132] Data abort info:
> [  191.074999]   ISV = 0, ISS = 0x00000004
> [  191.078822]   CM = 0, WnR = 0
> [  191.081780] user pgtable: 4k pages, 48-bit VAs, pgdp = 0000000043d9e467
> [  191.088382] [0000000000000000] pgd=0000000000000000
> [  191.093252] Internal error: Oops: 96000004 [#1] SMP
> [  191.098119] Modules linked in: vhost_net vhost tap vfio_pci vfio_virqfd vfio_iommu_type1 vfio xt_CHECKSUM iptable_mangle ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ipt_REJECT nf_reject_ipv4 xt_tcpudp bridge stp llc ebtable_filter devlink ebtables ip6table_filter ip6_tables iptable_filter bpfilter ipmi_ssif nls_iso8859_1 input_leds joydev ipmi_si hns_roce_hw_v2 ipmi_devintf hns_roce ipmi_msghandler cppc_cpufreq sch_fq_codel ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 ses enclosure btrfs zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor hid_generic usbhid hid raid6_pq libcrc32c raid1 raid0 multipath linear ixgbevf hibmc_drm ttm
> [  191.168607]  drm_kms_helper aes_ce_blk aes_ce_cipher syscopyarea crct10dif_ce sysfillrect ghash_ce qla2xxx sysimgblt sha2_ce sha256_arm64 hisi_sas_v3_hw fb_sys_fops sha1_ce uas nvme_fc mpt3sas ixgbe drm hisi_sas_main nvme_fabrics usb_storage hclge scsi_transport_fc ahci libsas hnae3 raid_class libahci xfrm_algo scsi_transport_sas mdio aes_neon_bs aes_neon_blk crypto_simd cryptd aes_arm64
> [  191.202952] CPU: 94 PID: 0 Comm: swapper/94 Not tainted 4.19.0-rc1+ #11
> [  191.209553] Hardware name: Huawei D06 /D06, BIOS Hisilicon D06 UEFI RC0 - V1.20.01 04/26/2019
> [  191.218064] pstate: 20400089 (nzCv daIf +PAN -UAO)
> [  191.222873] pc : ixgbe_ipsec_vf_clear+0x60/0xd0 [ixgbe]
> [  191.228093] lr : ixgbe_msg_task+0x2d0/0x1088 [ixgbe]
> [  191.233044] sp : ffff000009b3bcd0
> [  191.236346] x29: ffff000009b3bcd0 x28: 0000000000000000
> [  191.241647] x27: ffff000009628000 x26: 0000000000000000
> [  191.246946] x25: ffff803f652d7600 x24: 0000000000000004
> [  191.252246] x23: ffff803f6a718900 x22: 0000000000000000
> [  191.257546] x21: 0000000000000000 x20: 0000000000000000
> [  191.262845] x19: 0000000000000000 x18: 0000000000000000
> [  191.268144] x17: 0000000000000000 x16: 0000000000000000
> [  191.273443] x15: 0000000000000000 x14: 0000000100000026
> [  191.278742] x13: 0000000100000025 x12: ffff8a5f7fbe0df0
> [  191.284042] x11: 000000010000000b x10: 0000000000000040
> [  191.289341] x9 : 0000000000001100 x8 : ffff803f6a824fd8
> [  191.294640] x7 : ffff803f6a825098 x6 : 0000000000000001
> [  191.299939] x5 : ffff000000f0ffc0 x4 : 0000000000000000
> [  191.305238] x3 : ffff000028c00000 x2 : ffff803f652d7600
> [  191.310538] x1 : 0000000000000000 x0 : ffff000000f205f0
> [  191.315838] Process swapper/94 (pid: 0, stack limit = 0x00000000addfed5a)
> [  191.322613] Call trace:
> [  191.325055]  ixgbe_ipsec_vf_clear+0x60/0xd0 [ixgbe]
> [  191.329927]  ixgbe_msg_task+0x2d0/0x1088 [ixgbe]
> [  191.334536]  ixgbe_msix_other+0x274/0x330 [ixgbe]
> [  191.339233]  __handle_irq_event_percpu+0x78/0x270
> [  191.343924]  handle_irq_event_percpu+0x40/0x98
> [  191.348355]  handle_irq_event+0x50/0xa8
> [  191.352180]  handle_fasteoi_irq+0xbc/0x148
> [  191.356263]  generic_handle_irq+0x34/0x50
> [  191.360259]  __handle_domain_irq+0x68/0xc0
> [  191.364343]  gic_handle_irq+0x84/0x180
> [  191.368079]  el1_irq+0xe8/0x180
> [  191.371208]  arch_cpu_idle+0x30/0x1a8
> [  191.374860]  do_idle+0x1dc/0x2a0
> [  191.378077]  cpu_startup_entry+0x2c/0x30
> [  191.381988]  secondary_start_kernel+0x150/0x1e0
> [  191.386506] Code: 6b15003f 54000320 f1404a9f 54000060 (79400260)
>
> Fixes: eda0333ac2930 ("ixgbe: add VF IPsec management")
> Signed-off-by: Dann Frazier <dann.frazier@canonical.com>
> Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> ---
>   drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c | 3 +++
>   1 file changed, 3 insertions(+)
>
> diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c
> index ff85ce5791a3..31629fc7e820 100644
> --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c
> +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c
> @@ -842,6 +842,9 @@ void ixgbe_ipsec_vf_clear(struct ixgbe_adapter *adapter, u32 vf)
>   	struct ixgbe_ipsec *ipsec = adapter->ipsec;
>   	int i;
>   
> +	if (!ipsec)
> +		return;
> +
>   	/* search rx sa table */
>   	for (i = 0; i < IXGBE_IPSEC_MAX_SA_COUNT && ipsec->num_rx_sa; i++) {
>   		if (!ipsec->rx_tbl[i].used)

Thanks Dann,

Acked-by: Shannon Nelson <snelson@pensando.io>

Re: [net-next 08/15] iavf: Fix up debug print macro

[Joe Perches]

On Fri, 2019-06-28 at 15:49 -0700, Jeff Kirsher wrote:
> This aligns the iavf_debug() macro with the other Intel drivers.
> 
> Add the bus number, bus_id field to i40e_bus_info so output shows
> each physical port(i.e func) in following format:
>   [[[[<domain>]:]<bus>]:][<slot>][.[<func>]]
> domains are numbered from 0 to ffff), bus (0-ff), slot (0-1f) and
> function (0-7).
> 
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
> ---
>  drivers/net/ethernet/intel/iavf/iavf_osdep.h | 10 +++++++---
>  1 file changed, 7 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/net/ethernet/intel/iavf/iavf_osdep.h b/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> index d39684558597..a452ce90679a 100644
> --- a/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> +++ b/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> @@ -44,8 +44,12 @@ struct iavf_virt_mem {
>  #define iavf_allocate_virt_mem(h, m, s) iavf_allocate_virt_mem_d(h, m, s)
>  #define iavf_free_virt_mem(h, m) iavf_free_virt_mem_d(h, m)
>  
> -#define iavf_debug(h, m, s, ...)  iavf_debug_d(h, m, s, ##__VA_ARGS__)
> -extern void iavf_debug_d(void *hw, u32 mask, char *fmt_str, ...)
> -	__printf(3, 4);
> +#define iavf_debug(h, m, s, ...)				\
> +do {								\
> +	if (((m) & (h)->debug_mask))				\
> +		pr_info("iavf %02x:%02x.%x " s,			\
> +			(h)->bus.bus_id, (h)->bus.device,	\
> +			(h)->bus.func, ##__VA_ARGS__);		\
> +} while (0)

Why not change the function to do this?

And if this is really wanted this particular way
the now unused function should be removed too.

But I suggest emitting at KERN_DEBUG and using
the more typical %pV vsprintf extension.

---

 drivers/net/ethernet/intel/iavf/iavf_main.c  | 25 ++++++++++++++-----------
 drivers/net/ethernet/intel/iavf/iavf_osdep.h |  9 ++++++---
 2 files changed, 20 insertions(+), 14 deletions(-)

diff --git a/drivers/net/ethernet/intel/iavf/iavf_main.c b/drivers/net/ethernet/intel/iavf/iavf_main.c
index 881561b36083..8504fd71d398 100644
--- a/drivers/net/ethernet/intel/iavf/iavf_main.c
+++ b/drivers/net/ethernet/intel/iavf/iavf_main.c
@@ -143,25 +143,28 @@ enum iavf_status iavf_free_virt_mem_d(struct iavf_hw *hw,
 }
 
 /**
- * iavf_debug_d - OS dependent version of debug printing
+ * _iavf_debug - OS dependent version of debug printing
  * @hw:  pointer to the HW structure
  * @mask: debug level mask
- * @fmt_str: printf-type format description
+ * @fmt: printf-type format description
  **/
-void iavf_debug_d(void *hw, u32 mask, char *fmt_str, ...)
+void _iavf_debug(const struct iavf_hw *hw, u32 mask, const char *fmt, ...)
 {
-	char buf[512];
-	va_list argptr;
+	struct va_format vaf;
+	va_list args;
 
-	if (!(mask & ((struct iavf_hw *)hw)->debug_mask))
+	if (!(hw->debug_mask & mask))
 		return;
 
-	va_start(argptr, fmt_str);
-	vsnprintf(buf, sizeof(buf), fmt_str, argptr);
-	va_end(argptr);
+	va_start(args, fmt);
 
-	/* the debug string is already formatted with a newline */
-	pr_info("%s", buf);
+	vaf.fmt = fmt;
+	vaf.va = &args;
+
+	pr_debug("iavf %02x:%02x.%x %pV",
+		 hw->bus.bus_id, hw->bus.device, hw->bus.func, &vaf);
+
+	va_end(args);
 }
 
 /**
diff --git a/drivers/net/ethernet/intel/iavf/iavf_osdep.h b/drivers/net/ethernet/intel/iavf/iavf_osdep.h
index d39684558597..0e6ac7d262c8 100644
--- a/drivers/net/ethernet/intel/iavf/iavf_osdep.h
+++ b/drivers/net/ethernet/intel/iavf/iavf_osdep.h
@@ -44,8 +44,11 @@ struct iavf_virt_mem {
 #define iavf_allocate_virt_mem(h, m, s) iavf_allocate_virt_mem_d(h, m, s)
 #define iavf_free_virt_mem(h, m) iavf_free_virt_mem_d(h, m)
 
-#define iavf_debug(h, m, s, ...)  iavf_debug_d(h, m, s, ##__VA_ARGS__)
-extern void iavf_debug_d(void *hw, u32 mask, char *fmt_str, ...)
-	__printf(3, 4);
+struct iavf_hw;
+
+__printf(3, 4)
+void _iavf_debug(const struct iavf_hw *hw, u32 mask, const char *fmt, ...);
+#define iavf_debug(hw, mask, fmt, ...)					\
+	_iavf_debug(hw, mask, fmt, ##__VA_ARGS__)
 
 #endif /* _IAVF_OSDEP_H_ */

Re: [net-next 00/15][pull request] Intel Wired LAN Driver Updates 2019-06-28

[David Miller]

From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Date: Fri, 28 Jun 2019 15:49:17 -0700

> This series contains a smorgasbord of updates to many of the Intel
> drivers.
 ...

Pulled, thanks Jeff.

Please respond to Joe Perches's feedback on the debug macros.

Thanks.

Re: [net-next 08/15] iavf: Fix up debug print macro

[Jeff Kirsher]

[-- Attachment #1: Type: text/plain, Size: 4682 bytes --]

On Sat, 2019-06-29 at 13:42 -0700, Joe Perches wrote:
> On Fri, 2019-06-28 at 15:49 -0700, Jeff Kirsher wrote:
> > This aligns the iavf_debug() macro with the other Intel drivers.
> > 
> > Add the bus number, bus_id field to i40e_bus_info so output shows
> > each physical port(i.e func) in following format:
> >   [[[[<domain>]:]<bus>]:][<slot>][.[<func>]]
> > domains are numbered from 0 to ffff), bus (0-ff), slot (0-1f) and
> > function (0-7).
> > 
> > Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> > Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
> > ---
> >  drivers/net/ethernet/intel/iavf/iavf_osdep.h | 10 +++++++---
> >  1 file changed, 7 insertions(+), 3 deletions(-)
> > 
> > diff --git a/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> > b/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> > index d39684558597..a452ce90679a 100644
> > --- a/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> > +++ b/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> > @@ -44,8 +44,12 @@ struct iavf_virt_mem {
> >  #define iavf_allocate_virt_mem(h, m, s)
> > iavf_allocate_virt_mem_d(h, m, s)
> >  #define iavf_free_virt_mem(h, m) iavf_free_virt_mem_d(h, m)
> >  
> > -#define iavf_debug(h, m, s, ...)  iavf_debug_d(h, m, s,
> > ##__VA_ARGS__)
> > -extern void iavf_debug_d(void *hw, u32 mask, char *fmt_str, ...)
> > -	__printf(3, 4);
> > +#define iavf_debug(h, m, s, ...)				\
> > +do {								
> > \
> > +	if (((m) & (h)->debug_mask))				\
> > +		pr_info("iavf %02x:%02x.%x " s,			\
> > +			(h)->bus.bus_id, (h)->bus.device,	\
> > +			(h)->bus.func, ##__VA_ARGS__);		\
> > +} while (0)
> 
> Why not change the function to do this?
> 
> And if this is really wanted this particular way
> the now unused function should be removed too.
> 
> But I suggest emitting at KERN_DEBUG and using
> the more typical %pV vsprintf extension.

I see what you are saying, I was only looking at the macro in the osdep
to align with our other drivers and sync up with our internal driver
code.  Let me review the iavf driver debug function to see if there are
additional fix-ups/sync-ups needed.

> 
> ---
> 
>  drivers/net/ethernet/intel/iavf/iavf_main.c  | 25 ++++++++++++++--
> ---------
>  drivers/net/ethernet/intel/iavf/iavf_osdep.h |  9 ++++++---
>  2 files changed, 20 insertions(+), 14 deletions(-)
> 
> diff --git a/drivers/net/ethernet/intel/iavf/iavf_main.c
> b/drivers/net/ethernet/intel/iavf/iavf_main.c
> index 881561b36083..8504fd71d398 100644
> --- a/drivers/net/ethernet/intel/iavf/iavf_main.c
> +++ b/drivers/net/ethernet/intel/iavf/iavf_main.c
> @@ -143,25 +143,28 @@ enum iavf_status iavf_free_virt_mem_d(struct
> iavf_hw *hw,
>  }
>  
>  /**
> - * iavf_debug_d - OS dependent version of debug printing
> + * _iavf_debug - OS dependent version of debug printing
>   * @hw:  pointer to the HW structure
>   * @mask: debug level mask
> - * @fmt_str: printf-type format description
> + * @fmt: printf-type format description
>   **/
> -void iavf_debug_d(void *hw, u32 mask, char *fmt_str, ...)
> +void _iavf_debug(const struct iavf_hw *hw, u32 mask, const char
> *fmt, ...)
>  {
> -	char buf[512];
> -	va_list argptr;
> +	struct va_format vaf;
> +	va_list args;
>  
> -	if (!(mask & ((struct iavf_hw *)hw)->debug_mask))
> +	if (!(hw->debug_mask & mask))
>  		return;
>  
> -	va_start(argptr, fmt_str);
> -	vsnprintf(buf, sizeof(buf), fmt_str, argptr);
> -	va_end(argptr);
> +	va_start(args, fmt);
>  
> -	/* the debug string is already formatted with a newline */
> -	pr_info("%s", buf);
> +	vaf.fmt = fmt;
> +	vaf.va = &args;
> +
> +	pr_debug("iavf %02x:%02x.%x %pV",
> +		 hw->bus.bus_id, hw->bus.device, hw->bus.func, &vaf);
> +
> +	va_end(args);
>  }
>  
>  /**
> diff --git a/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> b/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> index d39684558597..0e6ac7d262c8 100644
> --- a/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> +++ b/drivers/net/ethernet/intel/iavf/iavf_osdep.h
> @@ -44,8 +44,11 @@ struct iavf_virt_mem {
>  #define iavf_allocate_virt_mem(h, m, s) iavf_allocate_virt_mem_d(h,
> m, s)
>  #define iavf_free_virt_mem(h, m) iavf_free_virt_mem_d(h, m)
>  
> -#define iavf_debug(h, m, s, ...)  iavf_debug_d(h, m, s,
> ##__VA_ARGS__)
> -extern void iavf_debug_d(void *hw, u32 mask, char *fmt_str, ...)
> -	__printf(3, 4);
> +struct iavf_hw;
> +
> +__printf(3, 4)
> +void _iavf_debug(const struct iavf_hw *hw, u32 mask, const char
> *fmt, ...);
> +#define iavf_debug(hw, mask, fmt, ...)				
> 	\
> +	_iavf_debug(hw, mask, fmt, ##__VA_ARGS__)
>  
>  #endif /* _IAVF_OSDEP_H_ */
> 
> 


[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 833 bytes --]