[PATCH AUTOSEL 5.4 001/108] net: wan: wanxl: use allow to pass CROSS_COMPILE_M68k for rebuilding firmware

[PATCH AUTOSEL 5.4 001/108] net: wan: wanxl: use allow to pass CROSS_COMPILE_M68k for rebuilding firmware

[Sasha Levin]

From: Masahiro Yamada <masahiroy@kernel.org>

[ Upstream commit 63b903dfebdea92aa92ad337d8451a6fbfeabf9d ]

As far as I understood from the Kconfig help text, this build rule is
used to rebuild the driver firmware, which runs on an old m68k-based
chip. So, you need m68k tools for the firmware rebuild.

wanxl.c is a PCI driver, but CONFIG_M68K does not select CONFIG_HAVE_PCI.
So, you cannot enable CONFIG_WANXL_BUILD_FIRMWARE for ARCH=m68k. In other
words, ifeq ($(ARCH),m68k) is false here.

I am keeping the dead code for now, but rebuilding the firmware requires
'as68k' and 'ld68k', which I do not have in hand.

Instead, the kernel.org m68k GCC [1] successfully built it.

Allowing a user to pass in CROSS_COMPILE_M68K= is handier.

[1] https://mirrors.edge.kernel.org/pub/tools/crosstool/files/bin/x86_64/9.2.0/x86_64-gcc-9.2.0-nolibc-m68k-linux.tar.xz

Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wan/Kconfig  |  2 +-
 drivers/net/wan/Makefile | 12 ++++++------
 2 files changed, 7 insertions(+), 7 deletions(-)

diff --git a/drivers/net/wan/Kconfig b/drivers/net/wan/Kconfig
index dd1a147f29716..058d77d2e693d 100644
--- a/drivers/net/wan/Kconfig
+++ b/drivers/net/wan/Kconfig
@@ -200,7 +200,7 @@ config WANXL_BUILD_FIRMWARE
 	depends on WANXL && !PREVENT_FIRMWARE_BUILD
 	help
 	  Allows you to rebuild firmware run by the QUICC processor.
-	  It requires as68k, ld68k and hexdump programs.
+	  It requires m68k toolchains and hexdump programs.
 
 	  You should never need this option, say N.
 
diff --git a/drivers/net/wan/Makefile b/drivers/net/wan/Makefile
index 701f5d2fe3b61..995277c657a1e 100644
--- a/drivers/net/wan/Makefile
+++ b/drivers/net/wan/Makefile
@@ -40,17 +40,17 @@ $(obj)/wanxl.o:	$(obj)/wanxlfw.inc
 
 ifeq ($(CONFIG_WANXL_BUILD_FIRMWARE),y)
 ifeq ($(ARCH),m68k)
-  AS68K = $(AS)
-  LD68K = $(LD)
+  M68KAS = $(AS)
+  M68KLD = $(LD)
 else
-  AS68K = as68k
-  LD68K = ld68k
+  M68KAS = $(CROSS_COMPILE_M68K)as
+  M68KLD = $(CROSS_COMPILE_M68K)ld
 endif
 
 quiet_cmd_build_wanxlfw = BLD FW  $@
       cmd_build_wanxlfw = \
-	$(CPP) -D__ASSEMBLY__ -Wp,-MD,$(depfile) -I$(srctree)/include/uapi $< | $(AS68K) -m68360 -o $(obj)/wanxlfw.o; \
-	$(LD68K) --oformat binary -Ttext 0x1000 $(obj)/wanxlfw.o -o $(obj)/wanxlfw.bin; \
+	$(CPP) -D__ASSEMBLY__ -Wp,-MD,$(depfile) -I$(srctree)/include/uapi $< | $(M68KAS) -m68360 -o $(obj)/wanxlfw.o; \
+	$(M68KLD) --oformat binary -Ttext 0x1000 $(obj)/wanxlfw.o -o $(obj)/wanxlfw.bin; \
 	hexdump -ve '"\n" 16/1 "0x%02X,"' $(obj)/wanxlfw.bin | sed 's/0x  ,//g;1s/^/static const u8 firmware[]={/;$$s/,$$/\n};\n/' >$(obj)/wanxlfw.inc; \
 	rm -f $(obj)/wanxlfw.bin $(obj)/wanxlfw.o
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 002/108] netfilter: ctnetlink: be more strict when NF_CONNTRACK_MARK is not set

[Sasha Levin]

From: Romain Bellan <romain.bellan@wifirst.fr>

[ Upstream commit 7c6b4121627aeaa79536fbb900feafec740410d3 ]

When CONFIG_NF_CONNTRACK_MARK is not set, any CTA_MARK or CTA_MARK_MASK
in netlink message are not supported. We should return an error when one
of them is set, not both

Fixes: 9306425b70bf ("netfilter: ctnetlink: must check mark attributes vs NULL")
Signed-off-by: Romain Bellan <romain.bellan@wifirst.fr>
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/nf_conntrack_netlink.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/netfilter/nf_conntrack_netlink.c b/net/netfilter/nf_conntrack_netlink.c
index aa8adf930b3ce..bb9c7569b9729 100644
--- a/net/netfilter/nf_conntrack_netlink.c
+++ b/net/netfilter/nf_conntrack_netlink.c
@@ -838,7 +838,7 @@ ctnetlink_alloc_filter(const struct nlattr * const cda[], u8 family)
 	struct ctnetlink_filter *filter;
 
 #ifndef CONFIG_NF_CONNTRACK_MARK
-	if (cda[CTA_MARK] && cda[CTA_MARK_MASK])
+	if (cda[CTA_MARK] || cda[CTA_MARK_MASK])
 		return ERR_PTR(-EOPNOTSUPP);
 #endif
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 003/108] net: axienet: Convert DMA error handler to a work queue

[Sasha Levin]

From: Andre Przywara <andre.przywara@arm.com>

[ Upstream commit 24201a64770afe2e17050b2ab9e8c0e24e9c23b2 ]

The DMA error handler routine is currently a tasklet, scheduled to run
after the DMA error IRQ was handled.
However it needs to take the MDIO mutex, which is not allowed to do in a
tasklet. A kernel (with debug options) complains consequently:
[  614.050361] net eth0: DMA Tx error 0x174019
[  614.064002] net eth0: Current BD is at: 0x8f84aa0ce
[  614.080195] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
[  614.109484] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 40, name: kworker/u4:4
[  614.135428] 3 locks held by kworker/u4:4/40:
[  614.149075]  #0: ffff000879863328 ((wq_completion)rpciod){....}, at: process_one_work+0x1f0/0x6a8
[  614.177528]  #1: ffff80001251bdf8 ((work_completion)(&task->u.tk_work)){....}, at: process_one_work+0x1f0/0x6a8
[  614.209033]  #2: ffff0008784e0110 (sk_lock-AF_INET-RPC){....}, at: tcp_sendmsg+0x24/0x58
[  614.235429] CPU: 0 PID: 40 Comm: kworker/u4:4 Not tainted 5.6.0-rc3-00926-g4a165a9d5921 #26
[  614.260854] Hardware name: ARM Test FPGA (DT)
[  614.274734] Workqueue: rpciod rpc_async_schedule
[  614.289022] Call trace:
[  614.296871]  dump_backtrace+0x0/0x1a0
[  614.308311]  show_stack+0x14/0x20
[  614.318751]  dump_stack+0xbc/0x100
[  614.329403]  ___might_sleep+0xf0/0x140
[  614.341018]  __might_sleep+0x4c/0x80
[  614.352201]  __mutex_lock+0x5c/0x8a8
[  614.363348]  mutex_lock_nested+0x1c/0x28
[  614.375654]  axienet_dma_err_handler+0x38/0x388
[  614.389999]  tasklet_action_common.isra.15+0x160/0x1a8
[  614.405894]  tasklet_action+0x24/0x30
[  614.417297]  efi_header_end+0xe0/0x494
[  614.429020]  irq_exit+0xd0/0xd8
[  614.439047]  __handle_domain_irq+0x60/0xb0
[  614.451877]  gic_handle_irq+0xdc/0x2d0
[  614.463486]  el1_irq+0xcc/0x180
[  614.473451]  __tcp_transmit_skb+0x41c/0xb58
[  614.486513]  tcp_write_xmit+0x224/0x10a0
[  614.498792]  __tcp_push_pending_frames+0x38/0xc8
[  614.513126]  tcp_rcv_established+0x41c/0x820
[  614.526301]  tcp_v4_do_rcv+0x8c/0x218
[  614.537784]  __release_sock+0x5c/0x108
[  614.549466]  release_sock+0x34/0xa0
[  614.560318]  tcp_sendmsg+0x40/0x58
[  614.571053]  inet_sendmsg+0x40/0x68
[  614.582061]  sock_sendmsg+0x18/0x30
[  614.593074]  xs_sendpages+0x218/0x328
[  614.604506]  xs_tcp_send_request+0xa0/0x1b8
[  614.617461]  xprt_transmit+0xc8/0x4f0
[  614.628943]  call_transmit+0x8c/0xa0
[  614.640028]  __rpc_execute+0xbc/0x6f8
[  614.651380]  rpc_async_schedule+0x28/0x48
[  614.663846]  process_one_work+0x298/0x6a8
[  614.676299]  worker_thread+0x40/0x490
[  614.687687]  kthread+0x134/0x138
[  614.697804]  ret_from_fork+0x10/0x18
[  614.717319] xilinx_axienet 7fe00000.ethernet eth0: Link is Down
[  615.748343] xilinx_axienet 7fe00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

Since tasklets are not really popular anymore anyway, lets convert this
over to a work queue, which can sleep and thus can take the MDIO mutex.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/xilinx/xilinx_axienet.h  |  2 +-
 .../net/ethernet/xilinx/xilinx_axienet_main.c | 24 +++++++++----------
 2 files changed, 13 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet.h b/drivers/net/ethernet/xilinx/xilinx_axienet.h
index 2dacfc85b3baa..04e51af32178c 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet.h
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet.h
@@ -435,7 +435,7 @@ struct axienet_local {
 	void __iomem *regs;
 	void __iomem *dma_regs;
 
-	struct tasklet_struct dma_err_tasklet;
+	struct work_struct dma_err_task;
 
 	int tx_irq;
 	int rx_irq;
diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
index 479325eeaf8a0..345a795666e92 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -806,7 +806,7 @@ static irqreturn_t axienet_tx_irq(int irq, void *_ndev)
 		/* Write to the Rx channel control register */
 		axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
 
-		tasklet_schedule(&lp->dma_err_tasklet);
+		schedule_work(&lp->dma_err_task);
 		axienet_dma_out32(lp, XAXIDMA_TX_SR_OFFSET, status);
 	}
 out:
@@ -855,7 +855,7 @@ static irqreturn_t axienet_rx_irq(int irq, void *_ndev)
 		/* write to the Rx channel control register */
 		axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
 
-		tasklet_schedule(&lp->dma_err_tasklet);
+		schedule_work(&lp->dma_err_task);
 		axienet_dma_out32(lp, XAXIDMA_RX_SR_OFFSET, status);
 	}
 out:
@@ -891,7 +891,7 @@ static irqreturn_t axienet_eth_irq(int irq, void *_ndev)
 	return IRQ_HANDLED;
 }
 
-static void axienet_dma_err_handler(unsigned long data);
+static void axienet_dma_err_handler(struct work_struct *work);
 
 /**
  * axienet_open - Driver open routine.
@@ -935,9 +935,8 @@ static int axienet_open(struct net_device *ndev)
 
 	phylink_start(lp->phylink);
 
-	/* Enable tasklets for Axi DMA error handling */
-	tasklet_init(&lp->dma_err_tasklet, axienet_dma_err_handler,
-		     (unsigned long) lp);
+	/* Enable worker thread for Axi DMA error handling */
+	INIT_WORK(&lp->dma_err_task, axienet_dma_err_handler);
 
 	/* Enable interrupts for Axi DMA Tx */
 	ret = request_irq(lp->tx_irq, axienet_tx_irq, IRQF_SHARED,
@@ -966,7 +965,7 @@ static int axienet_open(struct net_device *ndev)
 err_tx_irq:
 	phylink_stop(lp->phylink);
 	phylink_disconnect_phy(lp->phylink);
-	tasklet_kill(&lp->dma_err_tasklet);
+	cancel_work_sync(&lp->dma_err_task);
 	dev_err(lp->dev, "request_irq() failed\n");
 	return ret;
 }
@@ -1025,7 +1024,7 @@ static int axienet_stop(struct net_device *ndev)
 	axienet_mdio_enable(lp);
 	mutex_unlock(&lp->mii_bus->mdio_lock);
 
-	tasklet_kill(&lp->dma_err_tasklet);
+	cancel_work_sync(&lp->dma_err_task);
 
 	if (lp->eth_irq > 0)
 		free_irq(lp->eth_irq, ndev);
@@ -1505,17 +1504,18 @@ static const struct phylink_mac_ops axienet_phylink_ops = {
 };
 
 /**
- * axienet_dma_err_handler - Tasklet handler for Axi DMA Error
- * @data:	Data passed
+ * axienet_dma_err_handler - Work queue task for Axi DMA Error
+ * @work:	pointer to work_struct
  *
  * Resets the Axi DMA and Axi Ethernet devices, and reconfigures the
  * Tx/Rx BDs.
  */
-static void axienet_dma_err_handler(unsigned long data)
+static void axienet_dma_err_handler(struct work_struct *work)
 {
 	u32 axienet_status;
 	u32 cr, i;
-	struct axienet_local *lp = (struct axienet_local *) data;
+	struct axienet_local *lp = container_of(work, struct axienet_local,
+						dma_err_task);
 	struct net_device *ndev = lp->ndev;
 	struct axidma_bd *cur_p;
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 004/108] net: phy: probe PHY drivers synchronously

[Sasha Levin]

From: Heiner Kallweit <hkallweit1@gmail.com>

[ Upstream commit 16983507742cbcaa5592af530872a82e82fb9c51 ]

If we have scenarios like

mdiobus_register()
	-> loads PHY driver module(s)
	-> registers PHY driver(s)
	-> may schedule async probe
phydev = mdiobus_get_phy()
<phydev action involving PHY driver>

or

phydev = phy_device_create()
	-> loads PHY driver module
	-> registers PHY driver
	-> may schedule async probe
<phydev action involving PHY driver>

then we expect the PHY driver to be bound to the phydev when triggering
the action. This may not be the case in case of asynchronous probing.
Therefore ensure that PHY drivers are probed synchronously.

Default still is sync probing, except async probing is explicitly
requested. I saw some comments that the intention is to promote
async probing for more parallelism in boot process and want to be
prepared for the case that the default is changed to async probing.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/phy/phy_device.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 0907c3d8d94a2..67d0f68f92316 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -2322,6 +2322,7 @@ int phy_driver_register(struct phy_driver *new_driver, struct module *owner)
 	new_driver->mdiodrv.driver.probe = phy_probe;
 	new_driver->mdiodrv.driver.remove = phy_remove;
 	new_driver->mdiodrv.driver.owner = owner;
+	new_driver->mdiodrv.driver.probe_type = PROBE_FORCE_SYNCHRONOUS;
 
 	retval = driver_register(&new_driver->mdiodrv.driver);
 	if (retval) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 009/108] ionic: check for NULL structs on teardown

[Sasha Levin]

From: Shannon Nelson <snelson@pensando.io>

[ Upstream commit a4674f34711b96b65bdc4d54eca88d2fd123bbc6 ]

Make sure the queue structs exist before trying to tear
them down to make for safer error recovery.

Fixes: 0f3154e6bcb3 ("ionic: Add Tx and Rx handling")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/ethernet/pensando/ionic/ionic_lif.c   | 26 ++++++++++---------
 .../net/ethernet/pensando/ionic/ionic_main.c  |  7 ++++-
 2 files changed, 20 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/pensando/ionic/ionic_lif.c b/drivers/net/ethernet/pensando/ionic/ionic_lif.c
index 134640412d7b7..21e126708cc20 100644
--- a/drivers/net/ethernet/pensando/ionic/ionic_lif.c
+++ b/drivers/net/ethernet/pensando/ionic/ionic_lif.c
@@ -303,19 +303,21 @@ static void ionic_qcqs_free(struct ionic_lif *lif)
 		lif->adminqcq = NULL;
 	}
 
-	for (i = 0; i < lif->nxqs; i++)
-		if (lif->rxqcqs[i].stats)
-			devm_kfree(dev, lif->rxqcqs[i].stats);
-
-	devm_kfree(dev, lif->rxqcqs);
-	lif->rxqcqs = NULL;
-
-	for (i = 0; i < lif->nxqs; i++)
-		if (lif->txqcqs[i].stats)
-			devm_kfree(dev, lif->txqcqs[i].stats);
+	if (lif->rxqcqs) {
+		for (i = 0; i < lif->nxqs; i++)
+			if (lif->rxqcqs[i].stats)
+				devm_kfree(dev, lif->rxqcqs[i].stats);
+		devm_kfree(dev, lif->rxqcqs);
+		lif->rxqcqs = NULL;
+	}
 
-	devm_kfree(dev, lif->txqcqs);
-	lif->txqcqs = NULL;
+	if (lif->txqcqs) {
+		for (i = 0; i < lif->nxqs; i++)
+			if (lif->txqcqs[i].stats)
+				devm_kfree(dev, lif->txqcqs[i].stats);
+		devm_kfree(dev, lif->txqcqs);
+		lif->txqcqs = NULL;
+	}
 }
 
 static void ionic_link_qcq_interrupts(struct ionic_qcq *src_qcq,
diff --git a/drivers/net/ethernet/pensando/ionic/ionic_main.c b/drivers/net/ethernet/pensando/ionic/ionic_main.c
index aab3114134128..20a384964fc52 100644
--- a/drivers/net/ethernet/pensando/ionic/ionic_main.c
+++ b/drivers/net/ethernet/pensando/ionic/ionic_main.c
@@ -236,11 +236,16 @@ static void ionic_adminq_cb(struct ionic_queue *q,
 
 static int ionic_adminq_post(struct ionic_lif *lif, struct ionic_admin_ctx *ctx)
 {
-	struct ionic_queue *adminq = &lif->adminqcq->q;
+	struct ionic_queue *adminq;
 	int err = 0;
 
 	WARN_ON(in_interrupt());
 
+	if (!lif->adminqcq)
+		return -EIO;
+
+	adminq = &lif->adminqcq->q;
+
 	spin_lock(&lif->adminq_lock);
 	if (!ionic_q_has_space(adminq, 1)) {
 		err = -ENOSPC;
-- 
2.20.1

[PATCH AUTOSEL 5.4 010/108] net: phy: mscc: accept all RGMII species in vsc85xx_mac_if_set

[Sasha Levin]

From: Vladimir Oltean <vladimir.oltean@nxp.com>

[ Upstream commit da206d65f2b293274f8082a26da4e43a1610da54 ]

The helper for configuring the pinout of the MII side of the PHY should
do so irrespective of whether RGMII delays are used or not. So accept
the ID, TXID and RXID variants as well, not just the no-delay RGMII
variant.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/phy/mscc.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/phy/mscc.c b/drivers/net/phy/mscc.c
index 2339b9381d216..05d7c5cd9a308 100644
--- a/drivers/net/phy/mscc.c
+++ b/drivers/net/phy/mscc.c
@@ -816,6 +816,9 @@ static int vsc85xx_mac_if_set(struct phy_device *phydev,
 	reg_val = phy_read(phydev, MSCC_PHY_EXT_PHY_CNTL_1);
 	reg_val &= ~(MAC_IF_SELECTION_MASK);
 	switch (interface) {
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_ID:
 	case PHY_INTERFACE_MODE_RGMII:
 		reg_val |= (MAC_IF_SELECTION_RGMII << MAC_IF_SELECTION_POS);
 		break;
-- 
2.20.1

[PATCH AUTOSEL 5.4 015/108] selftests/bpf: Fix test_progs's parsing of test numbers

[Sasha Levin]

From: Andrii Nakryiko <andriin@fb.com>

[ Upstream commit fc32490bff855a539d253c8a52c5a1ba51d1325a ]

When specifying disjoint set of tests, test_progs doesn't set skipped test's
array elements to false. This leads to spurious execution of tests that should
have been skipped. Fix it by explicitly initializing them to false.

Fixes: 3a516a0a3a7b ("selftests/bpf: add sub-tests support for test_progs")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200314013932.4035712-2-andriin@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/testing/selftests/bpf/test_progs.c | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)

diff --git a/tools/testing/selftests/bpf/test_progs.c b/tools/testing/selftests/bpf/test_progs.c
index 3bf18364c67c9..751be17980a91 100644
--- a/tools/testing/selftests/bpf/test_progs.c
+++ b/tools/testing/selftests/bpf/test_progs.c
@@ -361,7 +361,7 @@ static int libbpf_print_fn(enum libbpf_print_level level,
 
 int parse_num_list(const char *s, struct test_selector *sel)
 {
-	int i, set_len = 0, num, start = 0, end = -1;
+	int i, set_len = 0, new_len, num, start = 0, end = -1;
 	bool *set = NULL, *tmp, parsing_end = false;
 	char *next;
 
@@ -396,18 +396,19 @@ int parse_num_list(const char *s, struct test_selector *sel)
 			return -EINVAL;
 
 		if (end + 1 > set_len) {
-			set_len = end + 1;
-			tmp = realloc(set, set_len);
+			new_len = end + 1;
+			tmp = realloc(set, new_len);
 			if (!tmp) {
 				free(set);
 				return -ENOMEM;
 			}
+			for (i = set_len; i < start; i++)
+				tmp[i] = false;
 			set = tmp;
+			set_len = new_len;
 		}
-		for (i = start; i <= end; i++) {
+		for (i = start; i <= end; i++)
 			set[i] = true;
-		}
-
 	}
 
 	if (!set)
-- 
2.20.1

[PATCH AUTOSEL 5.4 016/108] libbpf: Ignore incompatible types with matching name during CO-RE relocation

[Sasha Levin]

From: Andrii Nakryiko <andriin@fb.com>

[ Upstream commit d121e1d34b72c4975ff0340901d926c0aaf98174 ]

When finding target type candidates, ignore forward declarations, functions,
and other named types of incompatible kind. Not doing this can cause false
errors.  See [0] for one such case (due to struct pt_regs forward
declaration).

  [0] https://github.com/iovisor/bcc/pull/2806#issuecomment-598543645

Fixes: ddc7c3042614 ("libbpf: implement BPF CO-RE offset relocation algorithm")
Reported-by: Wenbo Zhang <ethercflow@gmail.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200313172336.1879637-3-andriin@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/lib/bpf/libbpf.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/tools/lib/bpf/libbpf.c b/tools/lib/bpf/libbpf.c
index b6403712c2f4c..5f3a8b3a54ad7 100644
--- a/tools/lib/bpf/libbpf.c
+++ b/tools/lib/bpf/libbpf.c
@@ -2534,6 +2534,10 @@ static struct ids_vec *bpf_core_find_cands(const struct btf *local_btf,
 		if (str_is_empty(targ_name))
 			continue;
 
+		t = skip_mods_and_typedefs(targ_btf, i, NULL);
+		if (!btf_is_composite(t) && !btf_is_array(t))
+			continue;
+
 		targ_essent_len = bpf_core_essential_name_len(targ_name);
 		if (targ_essent_len != local_essent_len)
 			continue;
-- 
2.20.1

[PATCH AUTOSEL 5.4 019/108] ath10k: use kzalloc to read for ath10k_sdio_hif_diag_read

[Sasha Levin]

From: Wen Gong <wgong@codeaurora.org>

[ Upstream commit 402f2992b4d62760cce7c689ff216ea3bf4d6e8a ]

When use command to read values, it crashed.

command:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value count=1 bs=4 skip=$((0x100233))

It will call to ath10k_sdio_hif_diag_read with address = 0x4008cc and buf_len = 4.

Then system crash:
[ 1786.013258] Unable to handle kernel paging request at virtual address ffffffc00bd45000
[ 1786.013273] Mem abort info:
[ 1786.013281]   ESR = 0x96000045
[ 1786.013291]   Exception class = DABT (current EL), IL = 32 bits
[ 1786.013299]   SET = 0, FnV = 0
[ 1786.013307]   EA = 0, S1PTW = 0
[ 1786.013314] Data abort info:
[ 1786.013322]   ISV = 0, ISS = 0x00000045
[ 1786.013330]   CM = 0, WnR = 1
[ 1786.013342] swapper pgtable: 4k pages, 39-bit VAs, pgdp = 000000008542a60e
[ 1786.013350] [ffffffc00bd45000] pgd=0000000000000000, pud=0000000000000000
[ 1786.013368] Internal error: Oops: 96000045 [#1] PREEMPT SMP
[ 1786.013609] Process swapper/0 (pid: 0, stack limit = 0x0000000084b153c6)
[ 1786.013623] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.86 #137
[ 1786.013631] Hardware name: MediaTek krane sku176 board (DT)
[ 1786.013643] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[ 1786.013662] pc : __memcpy+0x94/0x180
[ 1786.013678] lr : swiotlb_tbl_unmap_single+0x84/0x150
[ 1786.013686] sp : ffffff8008003c60
[ 1786.013694] x29: ffffff8008003c90 x28: ffffffae96411f80
[ 1786.013708] x27: ffffffae960d2018 x26: ffffff8019a4b9a8
[ 1786.013721] x25: 0000000000000000 x24: 0000000000000001
[ 1786.013734] x23: ffffffae96567000 x22: 00000000000051d4
[ 1786.013747] x21: 0000000000000000 x20: 00000000fe6e9000
[ 1786.013760] x19: 0000000000000004 x18: 0000000000000020
[ 1786.013773] x17: 0000000000000001 x16: 0000000000000000
[ 1786.013787] x15: 00000000ffffffff x14: 00000000000044c0
[ 1786.013800] x13: 0000000000365ba4 x12: 0000000000000000
[ 1786.013813] x11: 0000000000000001 x10: 00000037be6e9000
[ 1786.013826] x9 : ffffffc940000000 x8 : 000000000bd45000
[ 1786.013839] x7 : 0000000000000000 x6 : ffffffc00bd45000
[ 1786.013852] x5 : 0000000000000000 x4 : 0000000000000000
[ 1786.013865] x3 : 0000000000000c00 x2 : 0000000000000004
[ 1786.013878] x1 : fffffff7be6e9004 x0 : ffffffc00bd45000
[ 1786.013891] Call trace:
[ 1786.013903]  __memcpy+0x94/0x180
[ 1786.013914]  unmap_single+0x6c/0x84
[ 1786.013925]  swiotlb_unmap_sg_attrs+0x54/0x80
[ 1786.013938]  __swiotlb_unmap_sg_attrs+0x8c/0xa4
[ 1786.013952]  msdc_unprepare_data+0x6c/0x84
[ 1786.013963]  msdc_request_done+0x58/0x84
[ 1786.013974]  msdc_data_xfer_done+0x1a0/0x1c8
[ 1786.013985]  msdc_irq+0x12c/0x17c
[ 1786.013996]  __handle_irq_event_percpu+0xe4/0x250
[ 1786.014006]  handle_irq_event_percpu+0x28/0x68
[ 1786.014015]  handle_irq_event+0x48/0x78
[ 1786.014026]  handle_fasteoi_irq+0xd0/0x1a0
[ 1786.014039]  __handle_domain_irq+0x84/0xc4
[ 1786.014050]  gic_handle_irq+0x124/0x1a4
[ 1786.014059]  el1_irq+0xb0/0x128
[ 1786.014072]  cpuidle_enter_state+0x298/0x328
[ 1786.014082]  cpuidle_enter+0x30/0x40
[ 1786.014094]  do_idle+0x190/0x268
[ 1786.014104]  cpu_startup_entry+0x24/0x28
[ 1786.014116]  rest_init+0xd4/0xe0
[ 1786.014126]  start_kernel+0x30c/0x38c
[ 1786.014139] Code: f8408423 f80084c3 36100062 b8404423 (b80044c3)
[ 1786.014150] ---[ end trace 3b02ddb698ea69ee ]---
[ 1786.015415] Kernel panic - not syncing: Fatal exception in interrupt
[ 1786.015433] SMP: stopping secondary CPUs
[ 1786.015447] Kernel Offset: 0x2e8d200000 from 0xffffff8008000000
[ 1786.015458] CPU features: 0x0,2188200c
[ 1786.015466] Memory Limit: none

For sdio chip, it need the memory which is kmalloc, if it is
vmalloc from ath10k_mem_value_read, then it have a memory error.
kzalloc of ath10k_sdio_hif_diag_read32 is the correct type, so
add kzalloc in ath10k_sdio_hif_diag_read to replace the buffer
which is vmalloc from ath10k_mem_value_read.

This patch only effect sdio chip.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/sdio.c | 18 ++++++++++++++----
 1 file changed, 14 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c
index 9870d2d095c87..8fe626deadeb0 100644
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -1582,23 +1582,33 @@ static int ath10k_sdio_hif_diag_read(struct ath10k *ar, u32 address, void *buf,
 				     size_t buf_len)
 {
 	int ret;
+	void *mem;
+
+	mem = kzalloc(buf_len, GFP_KERNEL);
+	if (!mem)
+		return -ENOMEM;
 
 	/* set window register to start read cycle */
 	ret = ath10k_sdio_write32(ar, MBOX_WINDOW_READ_ADDR_ADDRESS, address);
 	if (ret) {
 		ath10k_warn(ar, "failed to set mbox window read address: %d", ret);
-		return ret;
+		goto out;
 	}
 
 	/* read the data */
-	ret = ath10k_sdio_read(ar, MBOX_WINDOW_DATA_ADDRESS, buf, buf_len);
+	ret = ath10k_sdio_read(ar, MBOX_WINDOW_DATA_ADDRESS, mem, buf_len);
 	if (ret) {
 		ath10k_warn(ar, "failed to read from mbox window data address: %d\n",
 			    ret);
-		return ret;
+		goto out;
 	}
 
-	return 0;
+	memcpy(buf, mem, buf_len);
+
+out:
+	kfree(mem);
+
+	return ret;
 }
 
 static int ath10k_sdio_hif_diag_read32(struct ath10k *ar, u32 address,
-- 
2.20.1

[PATCH AUTOSEL 5.4 020/108] mwifiex: set needed_headroom, not hard_header_len

[Sasha Levin]

From: Brian Norris <briannorris@chromium.org>

[ Upstream commit 9454f7a895b822dd8fb4588fc55fda7c96728869 ]

hard_header_len provides limitations for things like AF_PACKET, such
that we don't allow transmitting packets smaller than this.

needed_headroom provides a suggested minimum headroom for SKBs, so that
we can trivally add our headers to the front.

The latter is the correct field to use in this case, while the former
mostly just prevents sending small AF_PACKET frames.

In any case, mwifiex already does its own bounce buffering [1] if we
don't have enough headroom, so hints (not hard limits) are all that are
needed.

This is the essentially the same bug (and fix) that brcmfmac had, fixed
in commit cb39288fd6bb ("brcmfmac: use ndev->needed_headroom to reserve
additional header space").

[1] mwifiex_hard_start_xmit():
	if (skb_headroom(skb) < MWIFIEX_MIN_DATA_HEADER_LEN) {
	[...]
		/* Insufficient skb headroom - allocate a new skb */

Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.gbhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/marvell/mwifiex/cfg80211.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/marvell/mwifiex/cfg80211.c b/drivers/net/wireless/marvell/mwifiex/cfg80211.c
index d896841685008..e63bc15c6e305 100644
--- a/drivers/net/wireless/marvell/mwifiex/cfg80211.c
+++ b/drivers/net/wireless/marvell/mwifiex/cfg80211.c
@@ -3052,7 +3052,7 @@ struct wireless_dev *mwifiex_add_virtual_intf(struct wiphy *wiphy,
 
 	dev->flags |= IFF_BROADCAST | IFF_MULTICAST;
 	dev->watchdog_timeo = MWIFIEX_DEFAULT_WATCHDOG_TIMEOUT;
-	dev->hard_header_len += MWIFIEX_MIN_DATA_HEADER_LEN;
+	dev->needed_headroom = MWIFIEX_MIN_DATA_HEADER_LEN;
 	dev->ethtool_ops = &mwifiex_ethtool_ops;
 
 	mdev_priv = netdev_priv(dev);
-- 
2.20.1

[PATCH AUTOSEL 5.4 021/108] Bluetooth: L2CAP: handle l2cap config request during open state

[Sasha Levin]

From: Howard Chung <howardchung@google.com>

[ Upstream commit 96298f640104e4cd9a913a6e50b0b981829b94ff ]

According to Core Spec Version 5.2 | Vol 3, Part A 6.1.5,
the incoming L2CAP_ConfigReq should be handled during
OPEN state.

The section below shows the btmon trace when running
L2CAP/COS/CFD/BV-12-C before and after this change.

=== Before ===
...
> ACL Data RX: Handle 256 flags 0x02 dlen 12                #22
      L2CAP: Connection Request (0x02) ident 2 len 4
        PSM: 1 (0x0001)
        Source CID: 65
< ACL Data TX: Handle 256 flags 0x00 dlen 16                #23
      L2CAP: Connection Response (0x03) ident 2 len 8
        Destination CID: 64
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 256 flags 0x00 dlen 12                #24
      L2CAP: Configure Request (0x04) ident 2 len 4
        Destination CID: 65
        Flags: 0x0000
> HCI Event: Number of Completed Packets (0x13) plen 5      #25
        Num handles: 1
        Handle: 256
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5      #26
        Num handles: 1
        Handle: 256
        Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 16                #27
      L2CAP: Configure Request (0x04) ident 3 len 8
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00                                            ..
< ACL Data TX: Handle 256 flags 0x00 dlen 18                #28
      L2CAP: Configure Response (0x05) ident 3 len 10
        Source CID: 65
        Flags: 0x0000
        Result: Success (0x0000)
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 672
> HCI Event: Number of Completed Packets (0x13) plen 5      #29
        Num handles: 1
        Handle: 256
        Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 14                #30
      L2CAP: Configure Response (0x05) ident 2 len 6
        Source CID: 64
        Flags: 0x0000
        Result: Success (0x0000)
> ACL Data RX: Handle 256 flags 0x02 dlen 20                #31
      L2CAP: Configure Request (0x04) ident 3 len 12
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00 91 02 11 11                                ......
< ACL Data TX: Handle 256 flags 0x00 dlen 14                #32
      L2CAP: Command Reject (0x01) ident 3 len 6
        Reason: Invalid CID in request (0x0002)
        Destination CID: 64
        Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5      #33
        Num handles: 1
        Handle: 256
        Count: 1
...
=== After ===
...
> ACL Data RX: Handle 256 flags 0x02 dlen 12               #22
      L2CAP: Connection Request (0x02) ident 2 len 4
        PSM: 1 (0x0001)
        Source CID: 65
< ACL Data TX: Handle 256 flags 0x00 dlen 16               #23
      L2CAP: Connection Response (0x03) ident 2 len 8
        Destination CID: 64
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 256 flags 0x00 dlen 12               #24
      L2CAP: Configure Request (0x04) ident 2 len 4
        Destination CID: 65
        Flags: 0x0000
> HCI Event: Number of Completed Packets (0x13) plen 5     #25
        Num handles: 1
        Handle: 256
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5     #26
        Num handles: 1
        Handle: 256
        Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 16               #27
      L2CAP: Configure Request (0x04) ident 3 len 8
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00                                            ..
< ACL Data TX: Handle 256 flags 0x00 dlen 18               #28
      L2CAP: Configure Response (0x05) ident 3 len 10
        Source CID: 65
        Flags: 0x0000
        Result: Success (0x0000)
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 672
> HCI Event: Number of Completed Packets (0x13) plen 5     #29
        Num handles: 1
        Handle: 256
        Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 14               #30
      L2CAP: Configure Response (0x05) ident 2 len 6
        Source CID: 64
        Flags: 0x0000
        Result: Success (0x0000)
> ACL Data RX: Handle 256 flags 0x02 dlen 20               #31
      L2CAP: Configure Request (0x04) ident 3 len 12
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00 91 02 11 11                                .....
< ACL Data TX: Handle 256 flags 0x00 dlen 18               #32
      L2CAP: Configure Response (0x05) ident 3 len 10
        Source CID: 65
        Flags: 0x0000
        Result: Success (0x0000)
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 672
< ACL Data TX: Handle 256 flags 0x00 dlen 12               #33
      L2CAP: Configure Request (0x04) ident 3 len 4
        Destination CID: 65
        Flags: 0x0000
> HCI Event: Number of Completed Packets (0x13) plen 5     #34
        Num handles: 1
        Handle: 256
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5     #35
        Num handles: 1
        Handle: 256
        Count: 1
...

Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/bluetooth/l2cap_core.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/net/bluetooth/l2cap_core.c b/net/bluetooth/l2cap_core.c
index a845786258a0b..2f3e437faedbc 100644
--- a/net/bluetooth/l2cap_core.c
+++ b/net/bluetooth/l2cap_core.c
@@ -4131,7 +4131,8 @@ static inline int l2cap_config_req(struct l2cap_conn *conn,
 		return 0;
 	}
 
-	if (chan->state != BT_CONFIG && chan->state != BT_CONNECT2) {
+	if (chan->state != BT_CONFIG && chan->state != BT_CONNECT2 &&
+	    chan->state != BT_CONNECTED) {
 		cmd_reject_invalid_cid(conn, cmd->ident, chan->scid,
 				       chan->dcid);
 		goto unlock;
-- 
2.20.1

[PATCH AUTOSEL 5.4 023/108] ath10k: fix not registering airtime of 11a station with WMM disable

[Sasha Levin]

From: Yibo Zhao <yiboz@codeaurora.org>

[ Upstream commit f9680c75d187f2d5b9288c02f7a432041d4447b4 ]

The tid of 11a station with WMM disable reported by FW is 0x10 in
tx completion. The tid 16 is mapped to a NULL txq since buffer
MMPDU capbility is not supported. Then 11a station's airtime will
not be registered due to NULL txq check. As a results, airtime of
11a station keeps unchanged in debugfs system.

Mask the tid along with IEEE80211_QOS_CTL_TID_MASK to make it in
the valid range.

Hardwares tested : QCA9984
Firmwares tested : 10.4-3.10-00047

Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/htt_rx.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index 9f0e7b4943ec6..e30160418802f 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -2732,7 +2732,8 @@ static void ath10k_htt_rx_tx_compl_ind(struct ath10k *ar,
 			continue;
 		}
 
-		tid = FIELD_GET(HTT_TX_PPDU_DUR_INFO0_TID_MASK, info0);
+		tid = FIELD_GET(HTT_TX_PPDU_DUR_INFO0_TID_MASK, info0) &
+						IEEE80211_QOS_CTL_TID_MASK;
 		tx_duration = __le32_to_cpu(ppdu_dur->tx_duration);
 
 		ieee80211_sta_register_airtime(peer->sta, tid, tx_duration, 0);
-- 
2.20.1

[PATCH AUTOSEL 5.4 025/108] net/mlx5e: Init ethtool steering for representors

[Sasha Levin]

From: Vlad Buslov <vladbu@mellanox.com>

[ Upstream commit 6783e8b29f636383af293a55336f036bc7ad5619 ]

During transition to uplink representors the code responsible for
initializing ethtool steering functionality wasn't added to representor
init rx routine. This causes NULL pointer dereference during configuration
of network flow classification rule with ethtool (only possible to
reproduce with next commit in this series which registers necessary ethtool
callbacks).

Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/mellanox/mlx5/core/en_rep.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c b/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
index cd9bb7c7b3413..397b70fb23e23 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_rep.c
@@ -1590,6 +1590,8 @@ static int mlx5e_init_rep_rx(struct mlx5e_priv *priv)
 	if (err)
 		goto err_destroy_ttc_table;
 
+	mlx5e_ethtool_init_steering(priv);
+
 	return 0;
 
 err_destroy_ttc_table:
-- 
2.20.1

[PATCH AUTOSEL 5.4 027/108] Bluetooth: Fix calculation of SCO handle for packet processing

[Sasha Levin]

From: Marcel Holtmann <marcel@holtmann.org>

[ Upstream commit debdedf2eb5a2d9777cabff40900772be13cd9f9 ]

When processing SCO packets, the handle is wrongly assumed as 16-bit
value. The actual size is 12-bits and the other 4-bits are used for
packet flags.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/bluetooth/hci_core.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/net/bluetooth/hci_core.c b/net/bluetooth/hci_core.c
index 9e19d5a3aac87..d136519d56542 100644
--- a/net/bluetooth/hci_core.c
+++ b/net/bluetooth/hci_core.c
@@ -4322,13 +4322,16 @@ static void hci_scodata_packet(struct hci_dev *hdev, struct sk_buff *skb)
 {
 	struct hci_sco_hdr *hdr = (void *) skb->data;
 	struct hci_conn *conn;
-	__u16 handle;
+	__u16 handle, flags;
 
 	skb_pull(skb, HCI_SCO_HDR_SIZE);
 
 	handle = __le16_to_cpu(hdr->handle);
+	flags  = hci_flags(handle);
+	handle = hci_handle(handle);
 
-	BT_DBG("%s len %d handle 0x%4.4x", hdev->name, skb->len, handle);
+	BT_DBG("%s len %d handle 0x%4.4x flags 0x%4.4x", hdev->name, skb->len,
+	       handle, flags);
 
 	hdev->stat.sco_rx++;
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 028/108] net: rmnet: add missing module alias

[Sasha Levin]

From: Taehee Yoo <ap420073@gmail.com>

[ Upstream commit eed22a0685d651fc531bc63f215bb2a71d4b98e5 ]

In the current rmnet code, there is no module alias.
So, RTNL couldn't load rmnet module automatically.

Test commands:
    ip link add dummy0 type dummy
    modprobe -rv rmnet
    ip link add rmnet0 link dummy0 type rmnet  mux_id 1

Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c b/drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c
index fbf4cbcf1a654..d846a0ccea8f0 100644
--- a/drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c
+++ b/drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c
@@ -475,4 +475,5 @@ static void __exit rmnet_exit(void)
 
 module_init(rmnet_init)
 module_exit(rmnet_exit)
+MODULE_ALIAS_RTNL_LINK("rmnet");
 MODULE_LICENSE("GPL v2");
-- 
2.20.1

[PATCH AUTOSEL 5.4 031/108] Bluetooth: guard against controllers sending zero'd events

[Sasha Levin]

From: Alain Michaud <alainm@chromium.org>

[ Upstream commit 08bb4da90150e2a225f35e0f642cdc463958d696 ]

Some controllers have been observed to send zero'd events under some
conditions.  This change guards against this condition as well as adding
a trace to facilitate diagnosability of this condition.

Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/bluetooth/hci_event.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
index c1d3a303d97fb..34d312ae3c61d 100644
--- a/net/bluetooth/hci_event.c
+++ b/net/bluetooth/hci_event.c
@@ -5833,6 +5833,11 @@ void hci_event_packet(struct hci_dev *hdev, struct sk_buff *skb)
 	u8 status = 0, event = hdr->evt, req_evt = 0;
 	u16 opcode = HCI_OP_NOP;
 
+	if (!event) {
+		bt_dev_warn(hdev, "Received unexpected HCI Event 00000000");
+		goto done;
+	}
+
 	if (hdev->sent_cmd && bt_cb(hdev->sent_cmd)->hci.req_event == event) {
 		struct hci_command_hdr *cmd_hdr = (void *) hdev->sent_cmd->data;
 		opcode = __le16_to_cpu(cmd_hdr->opcode);
@@ -6044,6 +6049,7 @@ void hci_event_packet(struct hci_dev *hdev, struct sk_buff *skb)
 		req_complete_skb(hdev, status, opcode, orig_skb);
 	}
 
+done:
 	kfree_skb(orig_skb);
 	kfree_skb(skb);
 	hdev->stat.evt_rx++;
-- 
2.20.1

[PATCH AUTOSEL 5.4 034/108] net: hns3: modify an unsuitable print when setting unknown duplex to fibre

[Sasha Levin]

From: Guangbin Huang <huangguangbin2@huawei.com>

[ Upstream commit 2d3db26d78805c9e06e26def0081c76e9bb0b7d6 ]

Currently, if device is in link down status and user uses
'ethtool -s' command to set speed but not specify duplex
mode, the duplex mode passed from ethtool to driver is
unknown value(255), and the fibre port will identify this
value as half duplex mode and print "only copper port
supports half duplex!". This message is confusing.

So for fibre port, only the setting duplex is half, prints
error and returns.

Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c b/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c
index 52c9d204fe3d9..a1f62e079f15a 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c
@@ -737,7 +737,7 @@ static int hns3_check_ksettings_param(const struct net_device *netdev,
 	if (ops->get_media_type)
 		ops->get_media_type(handle, &media_type, &module_type);
 
-	if (cmd->base.duplex != DUPLEX_FULL &&
+	if (cmd->base.duplex == DUPLEX_HALF &&
 	    media_type != HNAE3_MEDIA_TYPE_COPPER) {
 		netdev_err(netdev,
 			   "only copper port supports half duplex!");
-- 
2.20.1

[PATCH AUTOSEL 5.4 036/108] net: intel: e1000e: fix possible sleep-in-atomic-context bugs in e1000e_get_hw_semaphore()

[Sasha Levin]

From: Jia-Ju Bai <baijiaju1990@gmail.com>

[ Upstream commit 2e05f756c7099c8991142382648a37b0d4c85943 ]

The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:

drivers/net/ethernet/intel/e1000e/mac.c, 1366:
	usleep_range in e1000e_get_hw_semaphore
drivers/net/ethernet/intel/e1000e/80003es2lan.c, 322:
	e1000e_get_hw_semaphore in e1000_release_swfw_sync_80003es2lan
drivers/net/ethernet/intel/e1000e/80003es2lan.c, 197:
	e1000_release_swfw_sync_80003es2lan in e1000_release_phy_80003es2lan
drivers/net/ethernet/intel/e1000e/netdev.c, 4883:
	(FUNC_PTR) e1000_release_phy_80003es2lan in e1000e_update_phy_stats
drivers/net/ethernet/intel/e1000e/netdev.c, 4917:
	e1000e_update_phy_stats in e1000e_update_stats
drivers/net/ethernet/intel/e1000e/netdev.c, 5945:
	e1000e_update_stats in e1000e_get_stats64
drivers/net/ethernet/intel/e1000e/netdev.c, 5944:
	spin_lock in e1000e_get_stats64

drivers/net/ethernet/intel/e1000e/mac.c, 1384:
	usleep_range in e1000e_get_hw_semaphore
drivers/net/ethernet/intel/e1000e/80003es2lan.c, 322:
	e1000e_get_hw_semaphore in e1000_release_swfw_sync_80003es2lan
drivers/net/ethernet/intel/e1000e/80003es2lan.c, 197:
	e1000_release_swfw_sync_80003es2lan in e1000_release_phy_80003es2lan
drivers/net/ethernet/intel/e1000e/netdev.c, 4883:
	(FUNC_PTR) e1000_release_phy_80003es2lan in e1000e_update_phy_stats
drivers/net/ethernet/intel/e1000e/netdev.c, 4917:
	e1000e_update_phy_stats in e1000e_update_stats
drivers/net/ethernet/intel/e1000e/netdev.c, 5945:
	e1000e_update_stats in e1000e_get_stats64
drivers/net/ethernet/intel/e1000e/netdev.c, 5944:
	spin_lock in e1000e_get_stats64

(FUNC_PTR) means a function pointer is called.

To fix these bugs, usleep_range() is replaced with udelay().

These bugs are found by a static analysis tool STCheck written by myself.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/e1000e/mac.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index e531976f8a677..51512a73fdd07 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -1363,7 +1363,7 @@ s32 e1000e_get_hw_semaphore(struct e1000_hw *hw)
 		if (!(swsm & E1000_SWSM_SMBI))
 			break;
 
-		usleep_range(50, 100);
+		udelay(100);
 		i++;
 	}
 
@@ -1381,7 +1381,7 @@ s32 e1000e_get_hw_semaphore(struct e1000_hw *hw)
 		if (er32(SWSM) & E1000_SWSM_SWESMBI)
 			break;
 
-		usleep_range(50, 100);
+		udelay(100);
 	}
 
 	if (i == timeout) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 037/108] net: dsa: bcm_sf2: Also configure Port 5 for 2Gb/sec on 7278

[Sasha Levin]

From: Florian Fainelli <f.fainelli@gmail.com>

[ Upstream commit 7458bd540fa0a90220b9e8c349d910d9dde9caf8 ]

Either port 5 or port 8 can be used on a 7278 device, make sure that
port 5 also gets configured properly for 2Gb/sec in that case.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/dsa/bcm_sf2.c      | 3 +++
 drivers/net/dsa/bcm_sf2_regs.h | 1 +
 2 files changed, 4 insertions(+)

diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index 46dc913da852d..d4e804184c545 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -602,6 +602,9 @@ static void bcm_sf2_sw_mac_config(struct dsa_switch *ds, int port,
 	if (state->duplex == DUPLEX_FULL)
 		reg |= DUPLX_MODE;
 
+	if (priv->type == BCM7278_DEVICE_ID && dsa_is_cpu_port(ds, port))
+		reg |= GMIIP_SPEED_UP_2G;
+
 	core_writel(priv, reg, offset);
 }
 
diff --git a/drivers/net/dsa/bcm_sf2_regs.h b/drivers/net/dsa/bcm_sf2_regs.h
index d8a5e6269c0ef..7844781763359 100644
--- a/drivers/net/dsa/bcm_sf2_regs.h
+++ b/drivers/net/dsa/bcm_sf2_regs.h
@@ -178,6 +178,7 @@ enum bcm_sf2_reg_offs {
 #define  RXFLOW_CNTL			(1 << 4)
 #define  TXFLOW_CNTL			(1 << 5)
 #define  SW_OVERRIDE			(1 << 6)
+#define  GMIIP_SPEED_UP_2G		(1 << 7)
 
 #define CORE_WATCHDOG_CTRL		0x001e4
 #define  SOFTWARE_RESET			(1 << 7)
-- 
2.20.1

[PATCH AUTOSEL 5.4 038/108] sh_eth: check sh_eth_cpu_data::no_tx_cntrs when dumping registers

[Sasha Levin]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

[ Upstream commit 6eaeedc1aa27a423bd89043705eca39215015bb3 ]

When adding the sh_eth_cpu_data::no_tx_cntrs flag I forgot to add the
flag check to  __sh_eth_get_regs(), causing the non-existing TX counter
registers to be considered for dumping on the R7S72100 SoC (the register
offset sanity check has the final say here)...

Fixes: ce9134dff6d9 ("sh_eth: add sh_eth_cpu_data::no_tx_cntrs flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/renesas/sh_eth.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c
index 8aa1b1bda96d1..6488d19c0b4d2 100644
--- a/drivers/net/ethernet/renesas/sh_eth.c
+++ b/drivers/net/ethernet/renesas/sh_eth.c
@@ -2184,10 +2184,12 @@ static size_t __sh_eth_get_regs(struct net_device *ndev, u32 *buf)
 		add_reg(BCULR);
 	add_reg(MAHR);
 	add_reg(MALR);
-	add_reg(TROCR);
-	add_reg(CDCR);
-	add_reg(LCCR);
-	add_reg(CNDCR);
+	if (!cd->no_tx_cntrs) {
+		add_reg(TROCR);
+		add_reg(CDCR);
+		add_reg(LCCR);
+		add_reg(CNDCR);
+	}
 	add_reg(CEFCR);
 	add_reg(FRECR);
 	add_reg(TSFRCR);
-- 
2.20.1

[PATCH AUTOSEL 5.4 039/108] sh_eth: check sh_eth_cpu_data::cexcr when dumping registers

[Sasha Levin]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

[ Upstream commit f75ca32403dbf91e20c275719aab705401b9e718 ]

When adding the sh_eth_cpu_data::cexcr flag I forgot to add the flag
check to  __sh_eth_get_regs(), causing the non-existing RX packet counter
registers to be considered for dumping on  the R7S72100 SoC (the register
offset sanity check has the final say here)...

Fixes: 4c1d45850d5 ("sh_eth: add sh_eth_cpu_data::cexcr flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/renesas/sh_eth.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c
index 6488d19c0b4d2..59f5db1ef29e9 100644
--- a/drivers/net/ethernet/renesas/sh_eth.c
+++ b/drivers/net/ethernet/renesas/sh_eth.c
@@ -2194,8 +2194,10 @@ static size_t __sh_eth_get_regs(struct net_device *ndev, u32 *buf)
 	add_reg(FRECR);
 	add_reg(TSFRCR);
 	add_reg(TLFRCR);
-	add_reg(CERCR);
-	add_reg(CEECR);
+	if (cd->cexcr) {
+		add_reg(CERCR);
+		add_reg(CEECR);
+	}
 	add_reg(MAFCR);
 	if (cd->rtrate)
 		add_reg(RTRATE);
-- 
2.20.1

[PATCH AUTOSEL 5.4 040/108] sh_eth: check sh_eth_cpu_data::no_xdfar when dumping registers

[Sasha Levin]

From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

[ Upstream commit 7bf47f609f7eaac4f7e9c407a85ad78997288a38 ]

When adding the sh_eth_cpu_data::no_xdfar flag I forgot to add the flag
check to  __sh_eth_get_regs(), causing the non-existing RDFAR/TDFAR to be
considered for dumping on the R-Car gen1/2 SoCs (the register offset check
has the final say here)...

Fixes: 4c1d45850d5 ("sh_eth: add sh_eth_cpu_data::cexcr flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/renesas/sh_eth.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c
index 59f5db1ef29e9..7440da726d68f 100644
--- a/drivers/net/ethernet/renesas/sh_eth.c
+++ b/drivers/net/ethernet/renesas/sh_eth.c
@@ -2140,11 +2140,13 @@ static size_t __sh_eth_get_regs(struct net_device *ndev, u32 *buf)
 	add_reg(EESR);
 	add_reg(EESIPR);
 	add_reg(TDLAR);
-	add_reg(TDFAR);
+	if (!cd->no_xdfar)
+		add_reg(TDFAR);
 	add_reg(TDFXR);
 	add_reg(TDFFR);
 	add_reg(RDLAR);
-	add_reg(RDFAR);
+	if (!cd->no_xdfar)
+		add_reg(RDFAR);
 	add_reg(RDFXR);
 	add_reg(RDFFR);
 	add_reg(TRSCER);
-- 
2.20.1

[PATCH AUTOSEL 5.4 041/108] ice: Fix implicit queue mapping mode in ice_vsi_get_qs

[Sasha Levin]

From: Brett Creeley <brett.creeley@intel.com>

[ Upstream commit 39066dc549cf8a688f6e105a4e9f2a8abefbcebe ]

Currently in ice_vsi_get_qs() we set the mapping_mode for Tx and Rx to
vsi->[tx|rx]_mapping_mode, but the problem is vsi->[tx|rx]_mapping_mode
have not been set yet. This was working because ICE_VSI_MAP_CONTIG is
defined to 0. Fix this by being explicit with our mapping mode by
initializing the Tx and Rx structure's mapping_mode to
ICE_VSI_MAP_CONTIG and then setting the vsi->[tx|rx]_mapping_mode to the
[tx|rx]_qs_cfg.mapping_mode values.

Also, only assign the vsi->[tx|rx]_mapping_mode when the queues are
successfully mapped to the VSI. With this change there was no longer a
need to initialize the ret variable to 0 so remove that.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/ice/ice_lib.c | 21 ++++++++++++---------
 1 file changed, 12 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ethernet/intel/ice/ice_lib.c b/drivers/net/ethernet/intel/ice/ice_lib.c
index cc755382df256..4d995355e0f96 100644
--- a/drivers/net/ethernet/intel/ice/ice_lib.c
+++ b/drivers/net/ethernet/intel/ice/ice_lib.c
@@ -704,7 +704,7 @@ static int ice_vsi_get_qs(struct ice_vsi *vsi)
 		.scatter_count = ICE_MAX_SCATTER_TXQS,
 		.vsi_map = vsi->txq_map,
 		.vsi_map_offset = 0,
-		.mapping_mode = vsi->tx_mapping_mode
+		.mapping_mode = ICE_VSI_MAP_CONTIG
 	};
 	struct ice_qs_cfg rx_qs_cfg = {
 		.qs_mutex = &pf->avail_q_mutex,
@@ -714,18 +714,21 @@ static int ice_vsi_get_qs(struct ice_vsi *vsi)
 		.scatter_count = ICE_MAX_SCATTER_RXQS,
 		.vsi_map = vsi->rxq_map,
 		.vsi_map_offset = 0,
-		.mapping_mode = vsi->rx_mapping_mode
+		.mapping_mode = ICE_VSI_MAP_CONTIG
 	};
-	int ret = 0;
-
-	vsi->tx_mapping_mode = ICE_VSI_MAP_CONTIG;
-	vsi->rx_mapping_mode = ICE_VSI_MAP_CONTIG;
+	int ret;
 
 	ret = __ice_vsi_get_qs(&tx_qs_cfg);
-	if (!ret)
-		ret = __ice_vsi_get_qs(&rx_qs_cfg);
+	if (ret)
+		return ret;
+	vsi->tx_mapping_mode = tx_qs_cfg.mapping_mode;
 
-	return ret;
+	ret = __ice_vsi_get_qs(&rx_qs_cfg);
+	if (ret)
+		return ret;
+	vsi->rx_mapping_mode = rx_qs_cfg.mapping_mode;
+
+	return 0;
 }
 
 /**
-- 
2.20.1

[PATCH AUTOSEL 5.4 043/108] mt76: fix handling full tx queues in mt76_dma_tx_queue_skb_raw

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 93eaec7625f13cffb593b471405b017c7e64d4ee ]

Fixes a theoretical issue where it could potentially overwrite an existing
descriptor entry (and leaking its skb)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/dma.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/mediatek/mt76/dma.c b/drivers/net/wireless/mediatek/mt76/dma.c
index 6249a46c19762..026d996612fbe 100644
--- a/drivers/net/wireless/mediatek/mt76/dma.c
+++ b/drivers/net/wireless/mediatek/mt76/dma.c
@@ -261,10 +261,13 @@ mt76_dma_tx_queue_skb_raw(struct mt76_dev *dev, enum mt76_txq_id qid,
 	struct mt76_queue_buf buf;
 	dma_addr_t addr;
 
+	if (q->queued + 1 >= q->ndesc - 1)
+		goto error;
+
 	addr = dma_map_single(dev->dev, skb->data, skb->len,
 			      DMA_TO_DEVICE);
 	if (unlikely(dma_mapping_error(dev->dev, addr)))
-		return -ENOMEM;
+		goto error;
 
 	buf.addr = addr;
 	buf.len = skb->len;
@@ -275,6 +278,10 @@ mt76_dma_tx_queue_skb_raw(struct mt76_dev *dev, enum mt76_txq_id qid,
 	spin_unlock_bh(&q->lock);
 
 	return 0;
+
+error:
+	dev_kfree_skb(skb);
+	return -ENOMEM;
 }
 
 static int
-- 
2.20.1

[PATCH AUTOSEL 5.4 047/108] rtw88: 8822c: update power sequence to v16

[Sasha Levin]

From: Tzu-En Huang <tehuang@realtek.com>

[ Upstream commit 8299adec99b29f341f0ee4269f1ce70ca8508e78 ]

Fix switching xtal mode leads to BT USB error issue.

Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/realtek/rtw88/rtw8822c.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/net/wireless/realtek/rtw88/rtw8822c.c b/drivers/net/wireless/realtek/rtw88/rtw8822c.c
index de0505a6a365d..509cc76e6ba54 100644
--- a/drivers/net/wireless/realtek/rtw88/rtw8822c.c
+++ b/drivers/net/wireless/realtek/rtw88/rtw8822c.c
@@ -3336,6 +3336,11 @@ static struct rtw_pwr_seq_cmd trans_cardemu_to_act_8822c[] = {
 	 RTW_PWR_INTF_ALL_MSK,
 	 RTW_PWR_ADDR_MAC,
 	 RTW_PWR_CMD_WRITE, BIT(2), BIT(2)},
+	{0x1064,
+	 RTW_PWR_CUT_ALL_MSK,
+	 RTW_PWR_INTF_ALL_MSK,
+	 RTW_PWR_ADDR_MAC,
+	 RTW_PWR_CMD_WRITE, BIT(1), BIT(1)},
 	{0xFFFF,
 	 RTW_PWR_CUT_ALL_MSK,
 	 RTW_PWR_INTF_ALL_MSK,
-- 
2.20.1

[PATCH AUTOSEL 5.4 057/108] rsi: fix null pointer dereference during rsi_shutdown()

[Sasha Levin]

From: Martin Kepplinger <martin.kepplinger@puri.sm>

[ Upstream commit 16bbc3eb83728c03138191a5d23d84d38175fa26 ]

Appearently the hw pointer can be NULL while the module is loaded and
in that case rsi_shutdown() crashes due to the unconditional dereference.

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/rsi/rsi_91x_sdio.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/rsi/rsi_91x_sdio.c b/drivers/net/wireless/rsi/rsi_91x_sdio.c
index 1bebba4e85273..5d6143a551877 100644
--- a/drivers/net/wireless/rsi/rsi_91x_sdio.c
+++ b/drivers/net/wireless/rsi/rsi_91x_sdio.c
@@ -1468,12 +1468,15 @@ static void rsi_shutdown(struct device *dev)
 	struct rsi_91x_sdiodev *sdev =
 		(struct rsi_91x_sdiodev *)adapter->rsi_dev;
 	struct ieee80211_hw *hw = adapter->hw;
-	struct cfg80211_wowlan *wowlan = hw->wiphy->wowlan_config;
 
 	rsi_dbg(ERR_ZONE, "SDIO Bus shutdown =====>\n");
 
-	if (rsi_config_wowlan(adapter, wowlan))
-		rsi_dbg(ERR_ZONE, "Failed to configure WoWLAN\n");
+	if (hw) {
+		struct cfg80211_wowlan *wowlan = hw->wiphy->wowlan_config;
+
+		if (rsi_config_wowlan(adapter, wowlan))
+			rsi_dbg(ERR_ZONE, "Failed to configure WoWLAN\n");
+	}
 
 	if (IS_ENABLED(CONFIG_RSI_COEX) && adapter->priv->coex_mode > 1 &&
 	    adapter->priv->bt_adapter) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 060/108] mt76: mt7603: fix input validation issues for powersave-filtered frames

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit d55aa5e17461b8b423adae376978032c4a10a1d8 ]

Before extracting the tid out of the packet, check if it was qos-data.
Only accept tid values 0-7
Also, avoid accepting the hardware queue as skb queue mapping, it could
lead to an overrun. Instead, derive the hardware queue from the tid number,
in order to avoid issues with packets being filtered multiple times.
This also fixes a mismatch between hardware and software queue indexes.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/wireless/mediatek/mt76/mt7603/dma.c   | 19 +++++++++++++++----
 1 file changed, 15 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7603/dma.c b/drivers/net/wireless/mediatek/mt76/mt7603/dma.c
index 24d82a20d046d..86820cf31bb34 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7603/dma.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7603/dma.c
@@ -30,6 +30,16 @@ mt7603_init_tx_queue(struct mt7603_dev *dev, struct mt76_sw_queue *q,
 static void
 mt7603_rx_loopback_skb(struct mt7603_dev *dev, struct sk_buff *skb)
 {
+	static const u8 tid_to_ac[8] = {
+		IEEE80211_AC_BE,
+		IEEE80211_AC_BK,
+		IEEE80211_AC_BK,
+		IEEE80211_AC_BE,
+		IEEE80211_AC_VI,
+		IEEE80211_AC_VI,
+		IEEE80211_AC_VO,
+		IEEE80211_AC_VO
+	};
 	__le32 *txd = (__le32 *)skb->data;
 	struct ieee80211_hdr *hdr;
 	struct ieee80211_sta *sta;
@@ -38,7 +48,7 @@ mt7603_rx_loopback_skb(struct mt7603_dev *dev, struct sk_buff *skb)
 	void *priv;
 	int idx;
 	u32 val;
-	u8 tid;
+	u8 tid = 0;
 
 	if (skb->len < MT_TXD_SIZE + sizeof(struct ieee80211_hdr))
 		goto free;
@@ -56,15 +66,16 @@ mt7603_rx_loopback_skb(struct mt7603_dev *dev, struct sk_buff *skb)
 
 	priv = msta = container_of(wcid, struct mt7603_sta, wcid);
 	val = le32_to_cpu(txd[0]);
-	skb_set_queue_mapping(skb, FIELD_GET(MT_TXD0_Q_IDX, val));
-
 	val &= ~(MT_TXD0_P_IDX | MT_TXD0_Q_IDX);
 	val |= FIELD_PREP(MT_TXD0_Q_IDX, MT_TX_HW_QUEUE_MGMT);
 	txd[0] = cpu_to_le32(val);
 
 	sta = container_of(priv, struct ieee80211_sta, drv_priv);
 	hdr = (struct ieee80211_hdr *)&skb->data[MT_TXD_SIZE];
-	tid = *ieee80211_get_qos_ctl(hdr) & IEEE80211_QOS_CTL_TID_MASK;
+	if (ieee80211_is_data_qos(hdr->frame_control))
+		tid = *ieee80211_get_qos_ctl(hdr) &
+		      IEEE80211_QOS_CTL_TAG1D_MASK;
+	skb_set_queue_mapping(skb, tid_to_ac[tid]);
 	ieee80211_sta_set_buffered(sta, tid, true);
 
 	spin_lock_bh(&dev->ps_lock);
-- 
2.20.1

[PATCH AUTOSEL 5.4 066/108] Bluetooth: RFCOMM: fix ODEBUG bug in rfcomm_dev_ioctl

[Sasha Levin]

From: Qiujun Huang <hqjagain@gmail.com>

[ Upstream commit 71811cac8532b2387b3414f7cd8fe9e497482864 ]

Needn't call 'rfcomm_dlc_put' here, because 'rfcomm_dlc_exists' didn't
increase dlc->refcnt.

Reported-by: syzbot+4496e82090657320efc6@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Suggested-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/bluetooth/rfcomm/tty.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/net/bluetooth/rfcomm/tty.c b/net/bluetooth/rfcomm/tty.c
index 0c7d31c6c18cc..a58584949a955 100644
--- a/net/bluetooth/rfcomm/tty.c
+++ b/net/bluetooth/rfcomm/tty.c
@@ -413,10 +413,8 @@ static int __rfcomm_create_dev(struct sock *sk, void __user *arg)
 		dlc = rfcomm_dlc_exists(&req.src, &req.dst, req.channel);
 		if (IS_ERR(dlc))
 			return PTR_ERR(dlc);
-		else if (dlc) {
-			rfcomm_dlc_put(dlc);
+		if (dlc)
 			return -EBUSY;
-		}
 		dlc = rfcomm_dlc_alloc(GFP_KERNEL);
 		if (!dlc)
 			return -ENOMEM;
-- 
2.20.1

[PATCH AUTOSEL 5.4 068/108] ath10k: start recovery process when read int status fail for sdio

[Sasha Levin]

From: Wen Gong <wgong@codeaurora.org>

[ Upstream commit 37b7ecb75627699e96750db1e0c5ac56224245df ]

When running simulate crash stress test, it happened
"failed to read from address 0x800: -110".

Test steps:
1. Run command continuous
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash

2. error happened and it did not begin recovery for long time.
[74377.334846] ath10k_sdio mmc1:0001:1: simulating soft firmware crash
[74378.378217] ath10k_sdio mmc1:0001:1: failed to read from address 0x800: -110
[74378.378371] ath10k_sdio mmc1:0001:1: failed to process pending SDIO interrupts: -110

It has sdio errors since it can not read MBOX_HOST_INT_STATUS_ADDRESS,
then it has to do recovery process to recovery ath10k.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/sdio.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c
index 8fe626deadeb0..98ecddcfb32b9 100644
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -913,8 +913,11 @@ static int ath10k_sdio_mbox_read_int_status(struct ath10k *ar,
 	 */
 	ret = ath10k_sdio_read(ar, MBOX_HOST_INT_STATUS_ADDRESS,
 			       irq_proc_reg, sizeof(*irq_proc_reg));
-	if (ret)
+	if (ret) {
+		queue_work(ar->workqueue, &ar->restart_work);
+		ath10k_warn(ar, "read int status fail, start recovery\n");
 		goto out;
+	}
 
 	/* Update only those registers that are enabled */
 	*host_int_status = irq_proc_reg->host_int_status &
-- 
2.20.1

[PATCH AUTOSEL 5.4 076/108] net: axienet: Propagate failure of DMA descriptor setup

[Sasha Levin]

From: Andre Przywara <andre.przywara@arm.com>

[ Upstream commit ee44d0b78839b21591501424fd3cb3648cc803b5 ]

When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.

This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.

Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/ethernet/xilinx/xilinx_axienet_main.c | 26 ++++++++++++++-----
 1 file changed, 19 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
index 345a795666e92..bb6e52f3bdf9b 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -437,9 +437,10 @@ static void axienet_setoptions(struct net_device *ndev, u32 options)
 	lp->options |= options;
 }
 
-static void __axienet_device_reset(struct axienet_local *lp)
+static int __axienet_device_reset(struct axienet_local *lp)
 {
 	u32 timeout;
+
 	/* Reset Axi DMA. This would reset Axi Ethernet core as well. The reset
 	 * process of Axi DMA takes a while to complete as all pending
 	 * commands/transfers will be flushed or completed during this
@@ -455,9 +456,11 @@ static void __axienet_device_reset(struct axienet_local *lp)
 		if (--timeout == 0) {
 			netdev_err(lp->ndev, "%s: DMA reset timeout!\n",
 				   __func__);
-			break;
+			return -ETIMEDOUT;
 		}
 	}
+
+	return 0;
 }
 
 /**
@@ -470,13 +473,17 @@ static void __axienet_device_reset(struct axienet_local *lp)
  * areconnected to Axi Ethernet reset lines, this in turn resets the Axi
  * Ethernet core. No separate hardware reset is done for the Axi Ethernet
  * core.
+ * Returns 0 on success or a negative error number otherwise.
  */
-static void axienet_device_reset(struct net_device *ndev)
+static int axienet_device_reset(struct net_device *ndev)
 {
 	u32 axienet_status;
 	struct axienet_local *lp = netdev_priv(ndev);
+	int ret;
 
-	__axienet_device_reset(lp);
+	ret = __axienet_device_reset(lp);
+	if (ret)
+		return ret;
 
 	lp->max_frm_size = XAE_MAX_VLAN_FRAME_SIZE;
 	lp->options |= XAE_OPTION_VLAN;
@@ -491,9 +498,11 @@ static void axienet_device_reset(struct net_device *ndev)
 			lp->options |= XAE_OPTION_JUMBO;
 	}
 
-	if (axienet_dma_bd_init(ndev)) {
+	ret = axienet_dma_bd_init(ndev);
+	if (ret) {
 		netdev_err(ndev, "%s: descriptor allocation failed\n",
 			   __func__);
+		return ret;
 	}
 
 	axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
@@ -518,6 +527,8 @@ static void axienet_device_reset(struct net_device *ndev)
 	axienet_setoptions(ndev, lp->options);
 
 	netif_trans_update(ndev);
+
+	return 0;
 }
 
 /**
@@ -921,8 +932,9 @@ static int axienet_open(struct net_device *ndev)
 	 */
 	mutex_lock(&lp->mii_bus->mdio_lock);
 	axienet_mdio_disable(lp);
-	axienet_device_reset(ndev);
-	ret = axienet_mdio_enable(lp);
+	ret = axienet_device_reset(ndev);
+	if (ret == 0)
+		ret = axienet_mdio_enable(lp);
 	mutex_unlock(&lp->mii_bus->mdio_lock);
 	if (ret < 0)
 		return ret;
-- 
2.20.1

[PATCH AUTOSEL 5.4 077/108] brcmfmac: Fix driver crash on USB control transfer timeout

[Sasha Levin]

From: Raveendran Somu <raveendran.somu@cypress.com>

[ Upstream commit 93a5bfbc7cad8bf3dea81c9bc07761c1226a0860 ]

When the control transfer gets timed out, the error status
was returned without killing that urb, this leads to using
the same urb. This issue causes the kernel crash as the same
urb is sumbitted multiple times. The fix is to kill the
urb for timeout transfer before returning error

Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-2-git-send-email-chi-hsien.lin@cypress.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c
index 575ed19e91951..10387a7f5d565 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c
@@ -328,11 +328,12 @@ static int brcmf_usb_tx_ctlpkt(struct device *dev, u8 *buf, u32 len)
 		return err;
 	}
 	timeout = brcmf_usb_ioctl_resp_wait(devinfo);
-	clear_bit(0, &devinfo->ctl_op);
 	if (!timeout) {
 		brcmf_err("Txctl wait timed out\n");
+		usb_kill_urb(devinfo->ctl_urb);
 		err = -EIO;
 	}
+	clear_bit(0, &devinfo->ctl_op);
 	return err;
 }
 
@@ -358,11 +359,12 @@ static int brcmf_usb_rx_ctlpkt(struct device *dev, u8 *buf, u32 len)
 	}
 	timeout = brcmf_usb_ioctl_resp_wait(devinfo);
 	err = devinfo->ctl_urb_status;
-	clear_bit(0, &devinfo->ctl_op);
 	if (!timeout) {
 		brcmf_err("rxctl wait timed out\n");
+		usb_kill_urb(devinfo->ctl_urb);
 		err = -EIO;
 	}
+	clear_bit(0, &devinfo->ctl_op);
 	if (!err)
 		return devinfo->ctl_urb_actual_length;
 	else
-- 
2.20.1

[PATCH AUTOSEL 5.4 078/108] brcmfmac: Fix double freeing in the fmac usb data path

[Sasha Levin]

From: Raveendran Somu <raveendran.somu@cypress.com>

[ Upstream commit 78179869dc3f5c0059bbf5d931a2717f1ad97ecd ]

When the brcmf_fws_process_skb() fails to get hanger slot for
queuing the skb, it tries to free the skb.
But the caller brcmf_netdev_start_xmit() of that funciton frees
the packet on error return value.
This causes the double freeing and which caused the kernel crash.

Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-3-git-send-email-chi-hsien.lin@cypress.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c
index 2bd892df83cc5..80cc45c9aa4a1 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c
@@ -2145,8 +2145,7 @@ int brcmf_fws_process_skb(struct brcmf_if *ifp, struct sk_buff *skb)
 		brcmf_fws_enq(fws, BRCMF_FWS_SKBSTATE_DELAYED, fifo, skb);
 		brcmf_fws_schedule_deq(fws);
 	} else {
-		bphy_err(drvr, "drop skb: no hanger slot\n");
-		brcmf_txfinalize(ifp, skb, false);
+		bphy_err(drvr, "no hanger slot available\n");
 		rc = -ENOMEM;
 	}
 	brcmf_fws_unlock(fws);
-- 
2.20.1

[PATCH AUTOSEL 5.4 079/108] brcmfmac: fix the incorrect return value in brcmf_inform_single_bss().

[Sasha Levin]

From: Raveendran Somu <raveendran.somu@cypress.com>

[ Upstream commit bd9944918ceb28ede97f715d209e220db5e92c09 ]

The function brcmf_inform_single_bss returns the value as success,
even when the length exceeds the maximum value.
The fix is to send appropriate code on this error.
This issue is observed when Cypress test group reported random fmac
crashes when running their tests and the path was identified from the
crash logs. With this fix the random failure issue in Cypress test group
was resolved.

Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-4-git-send-email-chi-hsien.lin@cypress.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
index e3ebb7abbdaed..28e08de04986f 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
@@ -2812,7 +2812,7 @@ static s32 brcmf_inform_single_bss(struct brcmf_cfg80211_info *cfg,
 
 	if (le32_to_cpu(bi->length) > WL_BSS_INFO_MAX) {
 		bphy_err(drvr, "Bss info is larger than buffer. Discarding\n");
-		return 0;
+		return -EINVAL;
 	}
 
 	if (!bi->ctl_ch) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 080/108] xfrm: add prep for esp beet mode offload

[Sasha Levin]

From: Xin Long <lucien.xin@gmail.com>

[ Upstream commit 308491755f36c461ee67290af159fdba6be0169d ]

Like __xfrm_transport/mode_tunnel_prep(), this patch is to add
__xfrm_mode_beet_prep() to fix the transport_header for gso
segments, and reset skb mac_len, and pull skb data to the
proto inside esp.

This patch also fixes a panic, reported by ltp:

  # modprobe esp4_offload
  # runltp -f net_stress.ipsec_tcp

  [ 2452.780511] kernel BUG at net/core/skbuff.c:109!
  [ 2452.799851] Call Trace:
  [ 2452.800298]  <IRQ>
  [ 2452.800705]  skb_push.cold.98+0x14/0x20
  [ 2452.801396]  esp_xmit+0x17b/0x270 [esp4_offload]
  [ 2452.802799]  validate_xmit_xfrm+0x22f/0x2e0
  [ 2452.804285]  __dev_queue_xmit+0x589/0x910
  [ 2452.806264]  __neigh_update+0x3d7/0xa50
  [ 2452.806958]  arp_process+0x259/0x810
  [ 2452.807589]  arp_rcv+0x18a/0x1c

It was caused by the skb going to esp_xmit with a wrong transport
header.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/xfrm/xfrm_device.c | 28 +++++++++++++++++++++++++++-
 1 file changed, 27 insertions(+), 1 deletion(-)

diff --git a/net/xfrm/xfrm_device.c b/net/xfrm/xfrm_device.c
index 64486ad813411..0159de5ace90f 100644
--- a/net/xfrm/xfrm_device.c
+++ b/net/xfrm/xfrm_device.c
@@ -46,6 +46,25 @@ static void __xfrm_mode_tunnel_prep(struct xfrm_state *x, struct sk_buff *skb,
 	pskb_pull(skb, skb->mac_len + x->props.header_len);
 }
 
+static void __xfrm_mode_beet_prep(struct xfrm_state *x, struct sk_buff *skb,
+				  unsigned int hsize)
+{
+	struct xfrm_offload *xo = xfrm_offload(skb);
+	int phlen = 0;
+
+	if (xo->flags & XFRM_GSO_SEGMENT)
+		skb->transport_header = skb->network_header + hsize;
+
+	skb_reset_mac_len(skb);
+	if (x->sel.family != AF_INET6) {
+		phlen = IPV4_BEET_PHMAXLEN;
+		if (x->outer_mode.family == AF_INET6)
+			phlen += sizeof(struct ipv6hdr) - sizeof(struct iphdr);
+	}
+
+	pskb_pull(skb, skb->mac_len + hsize + (x->props.header_len - phlen));
+}
+
 /* Adjust pointers into the packet when IPsec is done at layer2 */
 static void xfrm_outer_mode_prep(struct xfrm_state *x, struct sk_buff *skb)
 {
@@ -66,9 +85,16 @@ static void xfrm_outer_mode_prep(struct xfrm_state *x, struct sk_buff *skb)
 			return __xfrm_transport_prep(x, skb,
 						     sizeof(struct ipv6hdr));
 		break;
+	case XFRM_MODE_BEET:
+		if (x->outer_mode.family == AF_INET)
+			return __xfrm_mode_beet_prep(x, skb,
+						     sizeof(struct iphdr));
+		if (x->outer_mode.family == AF_INET6)
+			return __xfrm_mode_beet_prep(x, skb,
+						     sizeof(struct ipv6hdr));
+		break;
 	case XFRM_MODE_ROUTEOPTIMIZATION:
 	case XFRM_MODE_IN_TRIGGER:
-	case XFRM_MODE_BEET:
 		break;
 	}
 }
-- 
2.20.1

[PATCH AUTOSEL 5.4 083/108] netfilter: nf_tables: silence a RCU-list warning in nft_table_lookup()

[Sasha Levin]

From: Qian Cai <cai@lca.pw>

[ Upstream commit 0a6a9515fe390976cd762c52d8d4f446d7a14285 ]

It is safe to traverse &net->nft.tables with &net->nft.commit_mutex
held using list_for_each_entry_rcu(). Silence the PROVE_RCU_LIST false
positive,

WARNING: suspicious RCU usage
net/netfilter/nf_tables_api.c:523 RCU-list traversed in non-reader section!!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
1 lock held by iptables/1384:
 #0: ffffffff9745c4a8 (&net->nft.commit_mutex){+.+.}, at: nf_tables_valid_genid+0x25/0x60 [nf_tables]

Call Trace:
 dump_stack+0xa1/0xea
 lockdep_rcu_suspicious+0x103/0x10d
 nft_table_lookup.part.0+0x116/0x120 [nf_tables]
 nf_tables_newtable+0x12c/0x7d0 [nf_tables]
 nfnetlink_rcv_batch+0x559/0x1190 [nfnetlink]
 nfnetlink_rcv+0x1da/0x210 [nfnetlink]
 netlink_unicast+0x306/0x460
 netlink_sendmsg+0x44b/0x770
 ____sys_sendmsg+0x46b/0x4a0
 ___sys_sendmsg+0x138/0x1a0
 __sys_sendmsg+0xb6/0x130
 __x64_sys_sendmsg+0x48/0x50
 do_syscall_64+0x69/0xf4
 entry_SYSCALL_64_after_hwframe+0x49/0xb3

Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/nf_tables_api.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/net/netfilter/nf_tables_api.c b/net/netfilter/nf_tables_api.c
index 068daff41f6e6..e94326cc853c2 100644
--- a/net/netfilter/nf_tables_api.c
+++ b/net/netfilter/nf_tables_api.c
@@ -456,7 +456,8 @@ static struct nft_table *nft_table_lookup(const struct net *net,
 	if (nla == NULL)
 		return ERR_PTR(-EINVAL);
 
-	list_for_each_entry_rcu(table, &net->nft.tables, list) {
+	list_for_each_entry_rcu(table, &net->nft.tables, list,
+				lockdep_is_held(&net->nft.commit_mutex)) {
 		if (!nla_strcmp(nla, table->name) &&
 		    table->family == family &&
 		    nft_active_genmask(table, genmask))
-- 
2.20.1

[PATCH AUTOSEL 5.4 106/108] svcrdma: Fix leak of transport addresses

[Sasha Levin]

From: Chuck Lever <chuck.lever@oracle.com>

[ Upstream commit 1a33d8a284b1e85e03b8c7b1ea8fb985fccd1d71 ]

Kernel memory leak detected:

unreferenced object 0xffff888849cdf480 (size 8):
  comm "kworker/u8:3", pid 2086, jiffies 4297898756 (age 4269.856s)
  hex dump (first 8 bytes):
    30 00 cd 49 88 88 ff ff                          0..I....
  backtrace:
    [<00000000acfc370b>] __kmalloc_track_caller+0x137/0x183
    [<00000000a2724354>] kstrdup+0x2b/0x43
    [<0000000082964f84>] xprt_rdma_format_addresses+0x114/0x17d [rpcrdma]
    [<00000000dfa6ed00>] xprt_setup_rdma_bc+0xc0/0x10c [rpcrdma]
    [<0000000073051a83>] xprt_create_transport+0x3f/0x1a0 [sunrpc]
    [<0000000053531a8e>] rpc_create+0x118/0x1cd [sunrpc]
    [<000000003a51b5f8>] setup_callback_client+0x1a5/0x27d [nfsd]
    [<000000001bd410af>] nfsd4_process_cb_update.isra.7+0x16c/0x1ac [nfsd]
    [<000000007f4bbd56>] nfsd4_run_cb_work+0x4c/0xbd [nfsd]
    [<0000000055c5586b>] process_one_work+0x1b2/0x2fe
    [<00000000b1e3e8ef>] worker_thread+0x1a6/0x25a
    [<000000005205fb78>] kthread+0xf6/0xfb
    [<000000006d2dc057>] ret_from_fork+0x3a/0x50

Introduce a call to xprt_rdma_free_addresses() similar to the way
that the TCP backchannel releases a transport's peer address
strings.

Fixes: 5d252f90a800 ("svcrdma: Add class for RDMA backwards direction transport")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/sunrpc/xprtrdma/svc_rdma_backchannel.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
index 908e78bb87c64..c4fb930779a92 100644
--- a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
+++ b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
@@ -250,6 +250,7 @@ xprt_rdma_bc_put(struct rpc_xprt *xprt)
 {
 	dprintk("svcrdma: %s: xprt %p\n", __func__, xprt);
 
+	xprt_rdma_free_addresses(xprt);
 	xprt_free(xprt);
 }
 
-- 
2.20.1

Re: [PATCH AUTOSEL 5.4 037/108] net: dsa: bcm_sf2: Also configure Port 5 for 2Gb/sec on 7278

[Florian Fainelli]

On 4/11/2020 4:08 PM, Sasha Levin wrote:
> From: Florian Fainelli <f.fainelli@gmail.com>
> 
> [ Upstream commit 7458bd540fa0a90220b9e8c349d910d9dde9caf8 ]
> 
> Either port 5 or port 8 can be used on a 7278 device, make sure that
> port 5 also gets configured properly for 2Gb/sec in that case.

This was later reverted with:

3f02735e5da5367e4cd563ce6e5c21ce27922248 ("Revert "net: dsa: bcm_sf2:
Also configure Port 5 for 2Gb/sec on 7278") please drop it from this
selection.
-- 
Florian