From: Heiko Stuebner <heiko@sntech.de>
To: davem@davemloft.net, kuba@kernel.org
Cc: robh+dt@kernel.org, andrew@lunn.ch, f.fainelli@gmail.com,
hkallweit1@gmail.com, linux@armlinux.org.uk,
netdev@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, heiko@sntech.de,
christoph.muellner@theobroma-systems.com,
Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Subject: [PATCH v2 2/2] net: phy: mscc: handle the clkout control on some phy variants
Date: Tue, 9 Jun 2020 15:31:40 +0200 [thread overview]
Message-ID: <20200609133140.1421109-2-heiko@sntech.de> (raw)
In-Reply-To: <20200609133140.1421109-1-heiko@sntech.de>
From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
At least VSC8530/8531/8540/8541 contain a clock output that can emit
a predefined rate of 25, 50 or 125MHz.
This may then feed back into the network interface as source clock.
So follow the example the at803x already set and introduce a
vsc8531,clk-out-frequency property to set that output.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
---
Hi Andrew,
I didn't change the property yet, do you have a suggestion on
how to name it though? Going by the other examples in the
ethernet-phy.yamls, something like enet-phy-clock-out-frequency ?
.../bindings/net/mscc-phy-vsc8531.txt | 3 +
drivers/net/phy/mscc/mscc.h | 9 ++
drivers/net/phy/mscc/mscc_main.c | 87 +++++++++++++++++--
3 files changed, 92 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
index 5ff37c68c941..4a1f50ae48e1 100644
--- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
+++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt
@@ -1,6 +1,8 @@
* Microsemi - vsc8531 Giga bit ethernet phy
Optional properties:
+- vsc8531,clk-out-frequency: Clock output frequency in Hertz.
+ Should be one of 25000000, 50000000, 125000000
- vsc8531,vddmac : The vddmac in mV. Allowed values is listed
in the first row of Table 1 (below).
This property is only used in combination
@@ -63,6 +65,7 @@ Example:
vsc8531_0: ethernet-phy@0 {
compatible = "ethernet-phy-id0007.0570";
+ vsc8531,clk-out-frequency = <125000000>;
vsc8531,vddmac = <3300>;
vsc8531,edge-slowdown = <7>;
vsc8531,led-0-mode = <LINK_1000_ACTIVITY>;
diff --git a/drivers/net/phy/mscc/mscc.h b/drivers/net/phy/mscc/mscc.h
index 414e3b31bb1f..c8c395a041c2 100644
--- a/drivers/net/phy/mscc/mscc.h
+++ b/drivers/net/phy/mscc/mscc.h
@@ -218,6 +218,13 @@ enum rgmii_clock_delay {
#define INT_MEM_DATA_M 0x00ff
#define INT_MEM_DATA(x) (INT_MEM_DATA_M & (x))
+#define MSCC_CLKOUT_CNTL 13
+#define CLKOUT_ENABLE BIT(15)
+#define CLKOUT_FREQ_MASK GENMASK(14, 13)
+#define CLKOUT_FREQ_25M (0x0 << 13)
+#define CLKOUT_FREQ_50M (0x1 << 13)
+#define CLKOUT_FREQ_125M (0x2 << 13)
+
#define MSCC_PHY_PROC_CMD 18
#define PROC_CMD_NCOMPLETED 0x8000
#define PROC_CMD_FAILED 0x4000
@@ -361,6 +368,8 @@ struct vsc8531_private {
*/
unsigned int base_addr;
+ u32 clkout_rate;
+
#if IS_ENABLED(CONFIG_MACSEC)
/* MACsec fields:
* - One SecY per device (enforced at the s/w implementation level)
diff --git a/drivers/net/phy/mscc/mscc_main.c b/drivers/net/phy/mscc/mscc_main.c
index 54cac9c295ad..012d5019d7c8 100644
--- a/drivers/net/phy/mscc/mscc_main.c
+++ b/drivers/net/phy/mscc/mscc_main.c
@@ -432,6 +432,18 @@ static int vsc85xx_dt_led_mode_get(struct phy_device *phydev,
return led_mode;
}
+static void vsc8531_dt_clkout_rate_get(struct phy_device *phydev)
+{
+ struct vsc8531_private *priv = phydev->priv;
+ struct device *dev = &phydev->mdio.dev;
+ struct device_node *of_node = dev->of_node;
+
+ if (!of_node)
+ return;
+
+ of_property_read_u32(of_node, "vsc8531,clk-out-frequency",
+ &priv->clkout_rate);
+}
#else
static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
{
@@ -444,6 +456,10 @@ static int vsc85xx_dt_led_mode_get(struct phy_device *phydev,
{
return default_mode;
}
+
+static void vsc8531_dt_clkout_rate_get(struct phy_device *phydev)
+{
+}
#endif /* CONFIG_OF_MDIO */
static int vsc85xx_dt_led_modes_get(struct phy_device *phydev,
@@ -1540,6 +1556,37 @@ static int vsc85xx_config_init(struct phy_device *phydev)
return 0;
}
+static int vsc8531_config_init(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531 = phydev->priv;
+ u16 val;
+ int rc;
+
+ rc = vsc85xx_config_init(phydev);
+ if (rc)
+ return rc;
+
+ switch (vsc8531->clkout_rate) {
+ case 0:
+ val = 0;
+ break;
+ case 25000000:
+ val = CLKOUT_FREQ_25M | CLKOUT_ENABLE;
+ break;
+ case 50000000:
+ val = CLKOUT_FREQ_50M | CLKOUT_ENABLE;
+ break;
+ case 125000000:
+ val = CLKOUT_FREQ_125M | CLKOUT_ENABLE;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return phy_write_paged(phydev, MSCC_PHY_PAGE_EXTENDED_GPIO,
+ MSCC_CLKOUT_CNTL, val);
+}
+
static int vsc8584_did_interrupt(struct phy_device *phydev)
{
int rc = 0;
@@ -2020,6 +2067,32 @@ static int vsc8514_probe(struct phy_device *phydev)
ARRAY_SIZE(vsc85xx_hw_stats));
}
+static int vsc8531_probe(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531;
+ int rate_magic, rc;
+ u32 default_mode[2] = {VSC8531_LINK_1000_ACTIVITY,
+ VSC8531_LINK_100_ACTIVITY};
+
+ rate_magic = vsc85xx_edge_rate_magic_get(phydev);
+ if (rate_magic < 0)
+ return rate_magic;
+
+ rc = vsc85xx_probe_helper(phydev, default_mode,
+ ARRAY_SIZE(default_mode),
+ VSC85XX_SUPP_LED_MODES,
+ vsc85xx_hw_stats,
+ ARRAY_SIZE(vsc85xx_hw_stats));
+ if (rc < 0)
+ return rc;
+
+ vsc8531 = phydev->priv;
+ vsc8531->rate_magic = rate_magic;
+ vsc8531_dt_clkout_rate_get(phydev);
+
+ return 0;
+}
+
static int vsc8574_probe(struct phy_device *phydev)
{
u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
@@ -2157,14 +2230,14 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_BASIC_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
- .probe = &vsc85xx_probe,
+ .probe = &vsc8531_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
@@ -2181,14 +2254,14 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
- .probe = &vsc85xx_probe,
+ .probe = &vsc8531_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
@@ -2205,14 +2278,14 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_BASIC_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
- .probe = &vsc85xx_probe,
+ .probe = &vsc8531_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
@@ -2229,7 +2302,7 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
--
2.26.2
next prev parent reply other threads:[~2020-06-09 13:32 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-09 13:31 [PATCH v2 1/2] net: phy: mscc: move shared probe code into a helper Heiko Stuebner
2020-06-09 13:31 ` Heiko Stuebner [this message]
2020-06-11 0:03 ` [PATCH v2 2/2] net: phy: mscc: handle the clkout control on some phy variants David Miller
2020-06-11 13:29 ` Andrew Lunn
2020-06-17 21:45 ` Rob Herring
2020-06-12 1:37 ` [PATCH v2 1/2] net: phy: mscc: move shared probe code into a helper David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200609133140.1421109-2-heiko@sntech.de \
--to=heiko@sntech.de \
--cc=andrew@lunn.ch \
--cc=christoph.muellner@theobroma-systems.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=heiko.stuebner@theobroma-systems.com \
--cc=hkallweit1@gmail.com \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=netdev@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).