[PATCH v3 0/2] Add Ethernet support for Intel Keem Bay SoC

[PATCH v3 0/2] Add Ethernet support for Intel Keem Bay SoC

[vineetha.g.jaya.kumaran]

From: "Vineetha G. Jaya Kumaran" <vineetha.g.jaya.kumaran@intel.com>

Hello,

This patch set enables support for Ethernet on the Intel Keem Bay SoC.
The first patch contains the required Device Tree bindings documentation, 
while the second patch adds the Intel platform glue layer for the stmmac
device driver.

This driver was tested on the Keem Bay evaluation module board.

Thank you.

Best regards,
Vineetha

Changes since v2:
-Add a select in DT documentation to avoid matching with all nodes containing 'snps,dwmac'
-Rebased to 5.9-rc1

Changes since v1:
-Removed clocks maxItems property from DT bindings documentation
-Removed phy compatible strings from DT bindings documentation

Rusaimi Amira Ruslan (1):
  net: stmmac: Add dwmac-intel-plat for GBE driver

Vineetha G. Jaya Kumaran (1):
  dt-bindings: net: Add bindings for Intel Keem Bay

 .../devicetree/bindings/net/intel,dwmac-plat.yaml  | 130 ++++++++++++++
 drivers/net/ethernet/stmicro/stmmac/Kconfig        |  10 ++
 drivers/net/ethernet/stmicro/stmmac/Makefile       |   1 +
 .../net/ethernet/stmicro/stmmac/dwmac-intel-plat.c | 191 +++++++++++++++++++++
 4 files changed, 332 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/intel,dwmac-plat.yaml
 create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c

-- 
1.9.1

[PATCH v3 1/2] dt-bindings: net: Add bindings for Intel Keem Bay

[vineetha.g.jaya.kumaran]

From: "Vineetha G. Jaya Kumaran" <vineetha.g.jaya.kumaran@intel.com>

Add Device Tree bindings documentation for the ethernet controller
on Intel Keem Bay.

Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
---
 .../devicetree/bindings/net/intel,dwmac-plat.yaml  | 130 +++++++++++++++++++++
 1 file changed, 130 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/intel,dwmac-plat.yaml

diff --git a/Documentation/devicetree/bindings/net/intel,dwmac-plat.yaml b/Documentation/devicetree/bindings/net/intel,dwmac-plat.yaml
new file mode 100644
index 00000000..fa3ebba
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/intel,dwmac-plat.yaml
@@ -0,0 +1,130 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/intel,dwmac-plat.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Intel DWMAC glue layer Device Tree Bindings
+
+maintainers:
+  - Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
+
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - intel,keembay-dwmac
+  required:
+    - compatible
+
+allOf:
+  - $ref: "snps,dwmac.yaml#"
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - intel,keembay-dwmac
+          - const: snps,dwmac-4.10a
+
+  clocks:
+    items:
+      - description: GMAC main clock
+      - description: PTP reference clock
+      - description: Tx clock
+
+  clock-names:
+    items:
+      - const: stmmaceth
+      - const: ptp_ref
+      - const: tx_clk
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+
+examples:
+# FIXME: Remove defines and include the correct header file
+# once it is available in mainline.
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #define MOVISOC_KMB_PSS_GBE
+    #define MOVISOC_KMB_PSS_AUX_GBE_PTP
+    #define MOVISOC_KMB_PSS_AUX_GBE_TX
+
+    stmmac_axi_setup: stmmac-axi-config {
+        snps,lpi_en;
+        snps,wr_osr_lmt = <0x0>;
+        snps,rd_osr_lmt = <0x2>;
+        snps,blen = <0 0 0 0 16 8 4>;
+    };
+
+    mtl_rx_setup: rx-queues-config {
+        snps,rx-queues-to-use = <2>;
+        snps,rx-sched-sp;
+        queue0 {
+            snps,dcb-algorithm;
+            snps,map-to-dma-channel = <0x0>;
+            snps,priority = <0x0>;
+        };
+
+        queue1 {
+            snps,dcb-algorithm;
+            snps,map-to-dma-channel = <0x1>;
+            snps,priority = <0x1>;
+        };
+    };
+
+    mtl_tx_setup: tx-queues-config {
+        snps,tx-queues-to-use = <2>;
+        snps,tx-sched-wrr;
+        queue0 {
+           snps,weight = <0x10>;
+           snps,dcb-algorithm;
+           snps,priority = <0x0>;
+        };
+
+        queue1 {
+            snps,weight = <0x10>;
+            snps,dcb-algorithm;
+            snps,priority = <0x1>;
+        };
+    };
+
+    gmac0: ethernet@3a000000 {
+        compatible = "intel,keembay-dwmac", "snps,dwmac-4.10a";
+        interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-names = "macirq";
+        reg = <0x3a000000 0x8000>;
+        snps,perfect-filter-entries = <128>;
+        phy-handle = <&eth_phy0>;
+        phy-mode = "rgmii";
+        rx-fifo-depth = <4096>;
+        tx-fifo-depth = <4096>;
+        clock-names = "stmmaceth", "ptp_ref", "tx_clk";
+        clocks = <&scmi_clk MOVISOC_KMB_PSS_GBE>,
+                 <&scmi_clk MOVISOC_KMB_PSS_AUX_GBE_PTP>,
+                 <&scmi_clk MOVISOC_KMB_PSS_AUX_GBE_TX>;
+        snps,pbl = <0x4>;
+        snps,axi-config = <&stmmac_axi_setup>;
+        snps,mtl-rx-config = <&mtl_rx_setup>;
+        snps,mtl-tx-config = <&mtl_tx_setup>;
+        snps,tso;
+        status = "okay";
+
+        mdio0 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            compatible = "snps,dwmac-mdio";
+
+            ethernet-phy@0 {
+                reg = <0>;
+            };
+        };
+    };
+
+...
-- 
1.9.1

[PATCH v3 2/2] net: stmmac: Add dwmac-intel-plat for GBE driver

[vineetha.g.jaya.kumaran]

From: Rusaimi Amira Ruslan <rusaimi.amira.rusaimi@intel.com>

Add dwmac-intel-plat to enable the stmmac driver in Intel Keem Bay.
Also add fix_mac_speed and tx_clk in order to change link speeds.
This is required as mac_speed_o is not connected in the
Intel Keem Bay SoC.

Signed-off-by: Rusaimi Amira Ruslan <rusaimi.amira.rusaimi@intel.com>
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
---
 drivers/net/ethernet/stmicro/stmmac/Kconfig        |  10 ++
 drivers/net/ethernet/stmicro/stmmac/Makefile       |   1 +
 .../net/ethernet/stmicro/stmmac/dwmac-intel-plat.c | 191 +++++++++++++++++++++
 3 files changed, 202 insertions(+)
 create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c

diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index 9a47c5a..7572cea 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -209,6 +209,16 @@ config DWMAC_IMX8
 	  device driver. This driver is used for i.MX8 series like
 	  iMX8MP/iMX8DXL GMAC ethernet controller.
 
+config DWMAC_INTEL_PLAT
+	tristate "Intel dwmac support"
+	depends on OF && COMMON_CLK
+	depends on STMMAC_ETH
+	help
+	  Support for ethernet controllers on Intel SoCs
+
+	  This selects the Intel platform specific glue layer support for
+	  the stmmac device driver. This driver is used for the Intel Keem Bay
+	  SoC.
 endif
 
 config DWMAC_INTEL
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index 295615a..24e6145 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_DWMAC_STM32)	+= dwmac-stm32.o
 obj-$(CONFIG_DWMAC_SUNXI)	+= dwmac-sunxi.o
 obj-$(CONFIG_DWMAC_SUN8I)	+= dwmac-sun8i.o
 obj-$(CONFIG_DWMAC_DWC_QOS_ETH)	+= dwmac-dwc-qos-eth.o
+obj-$(CONFIG_DWMAC_INTEL_PLAT)	+= dwmac-intel-plat.o
 obj-$(CONFIG_DWMAC_GENERIC)	+= dwmac-generic.o
 obj-$(CONFIG_DWMAC_IMX8)	+= dwmac-imx.o
 stmmac-platform-objs:= stmmac_platform.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c
new file mode 100644
index 00000000..ccac7bf
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c
@@ -0,0 +1,191 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Intel DWMAC platform driver
+ *
+ * Copyright(C) 2020 Intel Corporation
+ */
+
+#include <linux/ethtool.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/stmmac.h>
+
+#include "stmmac.h"
+#include "stmmac_platform.h"
+
+struct intel_dwmac {
+	struct device *dev;
+	struct clk *tx_clk;
+	const struct intel_dwmac_data *data;
+};
+
+struct intel_dwmac_data {
+	void (*fix_mac_speed)(void *priv, unsigned int speed);
+	unsigned long ptp_ref_clk_rate;
+	unsigned long tx_clk_rate;
+	bool tx_clk_en;
+};
+
+static void kmb_eth_fix_mac_speed(void *priv, unsigned int speed)
+{
+	struct intel_dwmac *dwmac = priv;
+	unsigned long rate;
+	int ret;
+
+	rate = clk_get_rate(dwmac->tx_clk);
+
+	switch (speed) {
+	case SPEED_1000:
+		rate = 125000000;
+		break;
+
+	case SPEED_100:
+		rate = 25000000;
+		break;
+
+	case SPEED_10:
+		rate = 2500000;
+		break;
+
+	default:
+		dev_err(dwmac->dev, "Invalid speed\n");
+		break;
+	}
+
+	ret = clk_set_rate(dwmac->tx_clk, rate);
+	if (ret)
+		dev_err(dwmac->dev, "Failed to configure tx clock rate\n");
+}
+
+static const struct intel_dwmac_data kmb_data = {
+	.fix_mac_speed = kmb_eth_fix_mac_speed,
+	.ptp_ref_clk_rate = 200000000,
+	.tx_clk_rate = 125000000,
+	.tx_clk_en = true,
+};
+
+static const struct of_device_id intel_eth_plat_match[] = {
+	{ .compatible = "intel,keembay-dwmac", .data = &kmb_data },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, intel_eth_plat_match);
+
+static int intel_eth_plat_probe(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct stmmac_priv *priv = netdev_priv(ndev);
+	struct plat_stmmacenet_data *plat_dat;
+	struct stmmac_resources stmmac_res;
+	const struct of_device_id *match;
+	struct intel_dwmac *dwmac;
+	unsigned long rate;
+	int ret;
+
+	plat_dat = priv->plat;
+	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+	if (ret)
+		return ret;
+
+	plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
+	if (IS_ERR(plat_dat)) {
+		dev_err(&pdev->dev, "dt configuration failed\n");
+		return PTR_ERR(plat_dat);
+	}
+
+	dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
+	if (!dwmac) {
+		ret = -ENOMEM;
+		goto err_remove_config_dt;
+	}
+
+	dwmac->dev = &pdev->dev;
+	dwmac->tx_clk = NULL;
+
+	match = of_match_device(intel_eth_plat_match, &pdev->dev);
+	if (match && match->data) {
+		dwmac->data = (const struct intel_dwmac_data *)match->data;
+
+		if (dwmac->data->fix_mac_speed)
+			plat_dat->fix_mac_speed = dwmac->data->fix_mac_speed;
+
+		/* Enable TX clock */
+		if (dwmac->data->tx_clk_en) {
+			dwmac->tx_clk = devm_clk_get(&pdev->dev, "tx_clk");
+			if (IS_ERR(dwmac->tx_clk))
+				goto err_remove_config_dt;
+
+			clk_prepare_enable(dwmac->tx_clk);
+
+			/* Check and configure TX clock rate */
+			rate = clk_get_rate(dwmac->tx_clk);
+			if (dwmac->data->tx_clk_rate &&
+			    rate != dwmac->data->tx_clk_rate) {
+				rate = dwmac->data->tx_clk_rate;
+				ret = clk_set_rate(dwmac->tx_clk, rate);
+				if (ret) {
+					dev_err(&pdev->dev,
+						"Failed to set tx_clk\n");
+					return ret;
+				}
+			}
+		}
+
+		/* Check and configure PTP ref clock rate */
+		rate = clk_get_rate(plat_dat->clk_ptp_ref);
+		if (dwmac->data->ptp_ref_clk_rate &&
+		    rate != dwmac->data->ptp_ref_clk_rate) {
+			rate = dwmac->data->ptp_ref_clk_rate;
+			ret = clk_set_rate(plat_dat->clk_ptp_ref, rate);
+			if (ret) {
+				dev_err(&pdev->dev,
+					"Failed to set clk_ptp_ref\n");
+				return ret;
+			}
+		}
+	}
+
+	plat_dat->bsp_priv = dwmac;
+
+	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
+	if (ret) {
+		if (dwmac->tx_clk)
+			clk_disable_unprepare(dwmac->tx_clk);
+
+		goto err_remove_config_dt;
+	}
+
+	return 0;
+
+err_remove_config_dt:
+	stmmac_remove_config_dt(pdev, plat_dat);
+
+	return ret;
+}
+
+static int intel_eth_plat_remove(struct platform_device *pdev)
+{
+	struct intel_dwmac *dwmac = get_stmmac_bsp_priv(&pdev->dev);
+	int ret;
+
+	ret = stmmac_pltfr_remove(pdev);
+
+	if (dwmac->tx_clk)
+		clk_disable_unprepare(dwmac->tx_clk);
+
+	return ret;
+}
+
+static struct platform_driver intel_eth_plat_driver = {
+	.probe  = intel_eth_plat_probe,
+	.remove = intel_eth_plat_remove,
+	.driver = {
+		.name		= "intel-eth-plat",
+		.pm		= &stmmac_pltfr_pm_ops,
+		.of_match_table = intel_eth_plat_match,
+	},
+};
+module_platform_driver(intel_eth_plat_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Intel DWMAC platform driver");
-- 
1.9.1

Re: [PATCH v3 0/2] Add Ethernet support for Intel Keem Bay SoC

[David Miller]

From: vineetha.g.jaya.kumaran@intel.com
Date: Wed, 26 Aug 2020 12:33:40 +0800

> This patch set enables support for Ethernet on the Intel Keem Bay SoC.
> The first patch contains the required Device Tree bindings documentation, 
> while the second patch adds the Intel platform glue layer for the stmmac
> device driver.
> 
> This driver was tested on the Keem Bay evaluation module board.
 ...

Series applied to net-next, thank you.